NEC PlasmaSync® 42VM1 Le manuel du propriétaire

Marque: NEC

Modèle: PlasmaSync® 42VM1

Catégorie: Téléviseurs

Taper: Le manuel du propriétaire

NEC Technologies

PlasmaSync Plasma Monitor

User’s Manual

Important Information

Warnings and Safety Precaution

The NEC plasma monitor is designed and manufac-

tured to provide long, trouble-free service. No main-

tenance other than cleaning is required. Use a soft

dry cloth to clean the panel. Never use solvents such

as alcohol or thinner to clean the panel surface.

The plasma display panel consists of fine picture ele-

ments (cells). Although NEC produces the plasma dis-

play panels with more than 99.99 percent active cells,

there may be some cells that do not produce light or

remain lit.

For operating safety and to avoid damage to the unit,

read carefully and observe the following instructions.

To avoid shock and fire hazards:

1. Provide adequate space for ventilation to avoid inter-

nal heat build-up. Do not cover rear vents or install in a

closed cabinet or shelves.

The unit is equipped with cooling fans. If you install

the unit in an enclosure, be sure there is adequate space

at the top of the unit to allow hot air to rise and escape.

If the monitor becomes too hot, the overheat protector

will be activated and the monitor will be turned off. If

this happens, turn off the power to the monitor and un-

plug the power cord. If the room where the monitor is

installed is particularly hot, move the monitor to a cooler

location, and wait for the monitor to cool for 60 min-

utes. If the problem persists, contact your NEC dealer

for service.

2. Do not use the power cord polarized plug with exten-

sion cords or outlets unless the prongs can be completely

inserted.

3. Do not expose unit to water or moisture.

4. Avoid damage to the power cord, and do not attempt to

modify the power cord.

5. Unplug unit during electrical storms or if unit will not

be used over a long period.

6. Do not open the cabinet which has potentially danger-

ous high voltage components inside. If the unit is dam-

aged in this way the warranty will be void. Moreover,

there is a serious risk of electric shock.

7. Do not attempt to service or repair the unit. NEC is not

liable for any bodily harm or damage caused if unquali-

fied persons attempt service or open the back cover.

Refer all service to authorized NEC Service Centers.

Precautions

Please read this manual carefully before using your NEC

plasma monitor and keep the manual handy for future

reference.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER. NO

USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

This symbol warns the user that uninsulated

voltage within the unit may have sufficient

magnitude to cause electric shock. There-

fore, it is dangerous to make any kind of

contact with any part inside of this unit.

This symbol alerts the user that important

literature concerning the operation and

maintenance of this unit has been included.

Therefore, it should be read carefully in

order to avoid any problems.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE

THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE

THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD

RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS

CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE

CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PER-

SONNEL.

WARNING

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when

the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct

the interference at his own expense.

CAUTION

To avoid damage and prolong operating life:

1. Use only with 120V 50/60Hz AC power supply. Con-

tinued operation at line voltages greater than 120 Volts

AC will shorten the life of the unit, and might even

cause a fire hazard.

2. Handle the unit carefully when installing it and do not

drop.

3. Locate set away from heat, excessive dust, and direct

sunlight.

4. Protect the inside of the unit from liquids and small

metal objects. In case of accident, unplug the unit and

have it serviced by an authorized NEC Service Center.

5. Do not hit or scratch the panel surface as this causes

flaws on the surface of the screen.

6. For correct installation and mounting it is strongly rec-

ommended to use a trained,authorized NEC dealer.

7. As is the case with any phosphor-based display (like a

CRT monitor, for example) light output will gradually

decrease over the life of a Plasma Display Panel.

Recommendations to avoid or minimize phosphor burn-in

Like all phosphor-based display devices and all other gas

plasma displays, plasma monitors can be susceptible to

phosphor burn under certain circumstances. Certain

operating conditions, such as the continuous display of a

static image over a prolonged period of time, can result in

phosphor burn if proper precautions are not taken. To pro-

tect your investment in this NEC plasma monitor, please

adhere to the following guidelines and recommendations

for minimizing the occurrence of image burn:

* Always enable and use your computer's screen saver

function during use with a computer input source.

* Display a moving image whenever possible.

* Always power down the monitor when you are finished

using it.

If the plasma monitor is in long term use or continuous

operation take the following measures to reduce the

likelihood of phosphor burn:

* Lower the Brightness and Contrast levels as much as

possible without impairing image readability.

* Display an image with many colors and color gradations

(ie. photographic or photo-realistic images).

* Create image content with minimal contrast between light

and dark areas, for example white characters on black

backgrounds. Use complementary or pastel color when-

ever possible.

* Avoid displaying images with few colors and distinct,

sharply defined borders between colors.

Contact NEC Technologies at 1-800-836-0655 for other

recommended procedures that will best suit your particu-

lar application needs.

NOTE:

When you connect a computer to this monitor, attach

the supplied ferrite cores. If you do not do this, this

monitor will not comform to mandatory CE or C-Tick

standards.

Attaching the ferrite cores.

Set the ferrite cores on the both ends of the DVI cable

(not supplied), and the one end of the power cable

(supplied).

Close the lid tightly until the clamps click.

DVI cable (not supplied)

Connector

core (small)

Power cable (supplied)

core (large)

Set side

(Plasma Monitor side)

Mises en garde et précautions de

sécurité

Le moniteur PlasmaSync NEC a été conçu et fabriqué

pour une utilisation fiable et durable. Il ne nécessite

aucun entretien en dehors du nettoyage. Utiliser un

chiffon doux et sec pour nettoyer la surface de l'écran.

Ne jamais utiliser de solvant comme l'alcool ou le

diluant. Le panneau à affichage plasma est constitué

de fines particules d'images ou pixels (cellules). Bien

que NEC produise des panneaux à affichage plasma

avec plus de 99,99 % de cellules actives, il peut y

avoir des cellules qui ne produisent pas de lumière

ou qui restent allumées.

Pour des raisons de sécurité et pour éviter

d'endommager l'appareil, lire attentivement les in-

structions suivantes.

Pour éviter les risques d'éléctrocution et d'incendie:

1. Laisser suffisament d'espace autour de l'appareil pour

la ventilation et éviter toute augmentation excessive de

la température interne. Ne pas couvrir les évents ou

l'installer dans un endroit trop exigu.

L'appareil est équipé de ventilateurs de refroidissement.

Si vous installez l'appareil dans un espace clos, assurez-

vous qu'il y ait suffisamment d'espace au dessus pour

permettre à l'air chaud de s'élever et de s'évacuer.

Si la température du moniteur devient excessive, la pro-

tection contre les surchauffes entrera en action et

coupera l'alimentation. Dans ce cas, éteindre l'appareil

et débrancher le câble d'alimentation. Si la température

de la pièce dans laquelle le moniteur est installé est

particulièrement excessive, déplacer l'appareil dans un

endroit plus frais et le laisser refroidir 60 minutes. Si le

problème persiste, prendre contact avec le revendeur

NEC pour le service après-vente.

2. Ne pas utiliser la fiche polarisée du cordon

d’alimentation avec des prolongateurs ou des prises de

courant, sauf si les lames peuvent être insérées à fond.

3. Ne pas exposer à L'eau ou à l’humidité.

4. Eviter d’endommager le cordon d’alimentation, et ne

pas modifier le cordon d’alimentation.

5. Débrancher l’appareil pendant les tempêtes ou si

l’appareil n’est pas utilisé pendant une longue période.

6. Ne pas ouvrir le coffret. Des composants de haute ten-

sion se trouvent à l’intérieur. Si l’appareil est

endommagé de cette manière, la garantie devient

caduque. De plus, il y a risque d’électrocution.

7. Ne pas essayer de réparer ou entretenir l’appareil soi-

même. NEC ne saura être tenu pour responsable pour

toute blessure ou dommage causé par des personnes

non qualifiées qui essayent de réparer ou d’ouvrir le

couvercle arrière. Confier toute réparation à un centre

de service agréé NEC.

Précautions

Veuillez lire ce manuel avec attention avant d'utiliser votre

moniteur PlasmaSync NEC et conserver ce manuel à portée

de la main pour une consultation ultérieure.

RISQUE D’ELECTROCUTION

NE PAS OUVRIR

MISE EN GARDE: AFIN DE REDUIRE LES RISQUES D’ELECTRO-

CUTION, NE PAS DEPOSER LE COUVERCLE, IL N’Y

A AUCUNE PIECE UTILISABLE A L’INTERIEUR DE

CET APPAREIL. NE CONFIER LES TRAVAUX

D’ENTRETIEN QU’A UN PERSONNEL QUALIFIE.

Ce symbole a pour but de prévenir l’utilisateur de la

présence d’une tension dangereuse, non isolée se trouvant

à l’intérieur de l’appareil. Elle est d’une intensité suffisante

pour constituer un risque d’électrocution. Eviter le con-

tact avec les pièces à l’intérieur de cet appareil.

Ce symbole a pour but de prévenir l’utilisateur de la

présence d’importantes instructions concernant l’entretien

et le fonctionnement de cet appareil. Par conséquent, elles

doivent être lues attentivement afin d’éviter des problèmes.

AVERTISSEMENT

AFIN DE REDUIRE LES RISQUES D’INCENDIE OU

D’ELECTROCUTION, NE PAS EXPOSER CET APPAREIL A LA

PLUIE OU A L’HUMIDITE. AUSSI, NE PAS UTILISER LA FICHE

POLARISEE AVEC UN PROLONGATEUR OU UNE AUTRE PRISE

DE COURANT SAUF SI CES LAMES PEUVENT ETRE INSEREES

A FOND. NE PAS OUVRIR LE COFFRET, DES COMPOSANTS

HAUTE TENSION SE TROUVENT A L’INTERIEUR. LAISSER A

UN PERSONNEL QUALIFIE LE SOIN DE REPARER CET

APPAREIL.

DOC avis de conformation

Cet appareil numérigue de la classe A respecte toutes les exi-

gences du Réglement sur le Matériel Brouilleur du Canada.

ATTENTION

Pour éviter des dommages et prolonger la durée de

service de l’appareil:

1. N’utiliser qu’une source d’alimentation de 120 V 50/

60 Hz CA. Le fait d’utiliser l’appareil en continu à des

tensions de ligne supérieures à 120 Volts CA réduit sa

durée de vie et risque de provoquer un incendie.

2. Manipuler l’appareil avec soin pendant son

déplacement et ne pas le faire tomber.

3. Eloigner l’appareil des endroits chauds, très poussiéreux

et exposés en plein soleil.

4. Eviter que des liquides et des petits objets métalliques

pénètrent à l’intérieur de l’appareil. En cas d’accident,

débrancher l’appareil et le confier à un centre de serv-

ice agréé NEC.

5. Ne pas frapper ou rayer la surface de la écran plasma,

car des défauts risquent de se produire sur la surface de

la écran plasma.

6. Pour effectuer une installation et un montage corrects,

il est recommandé de faire appel au concessionnaire

NEC autorisé et spécialisé.

7. Comme c'est le cas pour tout affichage à base de

phosphore (comme un moniteur CRT, par exemple), la

puissance de lumière baisse graduellement au cours de

la vie du Panneau d'Affichage à Plasma.

Pour éviter le risque de combustion au phosphore, les

mesures suivantes sont recommandées :

Comme tous les appareils d'affichage à base de phosphore

et tous les autres affichages à gaz plasma, les moniteurs

Plasmasync peuvent être sujets à la combustion au

phosphore dans certaines circonsatnces. Certaines condi-

tions d'utilisation, telles que l'affichage continu d'une im-

age statique pour une durée prolongée, peuvent causer des

brûlures au phophore si aucune précaution n'est prise. Pour

protéger votre investissement dans ce moniteur PlasmaSync

NEC, veuillez suivre les directives et les recommandations

suivantes pour minimiser l'occurence de brûlure d'image :

• Assurez-vous de mettre en marche et d'utliser

l'économisateur d'écran chaque fois que c'est possible

lorsque vous l'utilisez avec une source d'entrée

d'ordinateur.

• Affichez une image en mouvement aussi souvent que

possible.

• Coupez toujours l'alimentation lorsque vous avez terminé

d'utiliser la moniteur.

Si le moniteur est en usage continu ou longue durée, prenez

les mesures suivantes afin d'éviter l'occurence de

combustion au phosphore :

• Abaissez le niveau de l'image (contraste, luminosité)

autant que possible, sans faire perdre la lisibilité de

l'image.

• Affichez une image avec de nombreuses couleurs et

graduations de couleur (par ex. des images

photographiques ou photo-réalistes).

• Créez un contenu d'image avec un contraste minimal

entre les zones sombres et les zones claires, par exemple,

des caractères blancs sur un fond noir. Utilisez des

couleurs complémentaires ou pastels le plus souvent

possible.

• Évitez d'afficher des images avec peu de couleurs et des

limites nettes et clairement définies entre les couleurs.

Contactez NEC Technologies au 1-800-836-0655 pour

d'autres procédures recommandées qui conviendront le

mieux au besoin de votre appareil.

REMARQUE:

Lorsque vous branchez un micro-ordinateur sur ce

moniteur, fixez les noyaux en ferrites fournis. Si vous

ne le faîtes, le moniteur ne sera pas en conformité avec

les exigences des standards FCC.

Fixation des noyaux en ferrite.

Installez les noyaux en ferrite sur chaque bout du câble

DVI (non fourni), ainsi que sur un côté du câble

d'alimentation électrique (founi).

Fermez doucement le couvercle jusqu'à ce que les crans

se clipsent.

Câble DVI (non fourni)

Connecteur

noyau (petit)

noyau (large)

Câble d'alimentation

électrique (fourni)

Côté de l'appareil

(côté du moniteur à plasma)

NEC Technologies, Inc. (hereinafter NECTECH) warrants

this product to be free from defects in material and work-

manship under the following terms and, subject to the con-

ditions set forth below, agrees to repair or replace (at

NECTECH's sole option) any part of the enclosed unit

which proves defective. Replacement parts or products may

be new or refurbished and will meet specifications of the

original parts or product.

HOW LONG IS THE WARRANTY?

Parts and labor are warranted for (1) One Year from the

date of the first customer purchase.

WHO IS PROTECTED?

This warranty may be enforced only by the first purchaser.

WHAT IS COVERED AND WHAT IS NOT COVERED

Except as specified below, this warranty covers all defects

in material or workmanship in this product. The following

are not covered by the warranty:

1. Any product which is not distributed in the U.S.A. or

Canada and Mexico by NECTECH or which is not

purchased in the U.S.A. or Canada or Mexico from an

authorized NECTECH dealer.

2. Any product on which the serial number has been de-

faced, modified or removed.

3. Damage, deterioration or malfunction resulting from:

a.Accident, misuse, abuse, neglect, fire, water, light-

ning or other acts of nature, unauthorized product

modification, or failure to follow instructions sup-

plied with the product.

b.Repair or attempted repair by anyone not authorized

by NECTECH.

c.Any shipment of the product (claims must be pre-

sented to the carrier).

d.Removal or installation of the product.

e.Any other cause which does not relate to a product

defect.

f. Burns or residual images upon the phosphor of the

panel.

4. Cartons, carrying cases, batteries, external cabinets,

magnetic tapes, or any accessories used in connection

with the product.

5. Service outside of the U.S.A. and Canada.

WHAT WE WILL PAY FOR AND WHAT WE WILL

NOT PAY FOR

We will pay labor and material expenses for covered items,

but we will not pay for the following:

1. Removal or installation charges.

2. Costs of initial technical adjustments (set-up), includ-

ing adjustment of user controls. These costs are the re-

sponsibility of the NECTECH dealer from whom the

product was purchased.

3. Payment of shipping charges.

HOW YOU CAN GET WARRANTY SERVICE

1. To obtain service on your product, consult the dealer

from whom you purchased the product.

2. Whenever warranty service is required, the original

dated invoice (or a copy) must be presented as proof of

warranty coverage. Please also include in any mailing

your name, address and a description of the problem(s).

3. For the name of the nearest NECTECH authorized serv-

ice center, call NECTECH at 800-836-0655.

LIMITATIONS OF LIABILITY

Except for the obligations specifically set forth in this war-

ranty statement, we will not be liable for any direct, indi-

rect, special, incidental, consequential, or other types of

damages, whether based on contract, tort, or any other le-

gal theory, whether or not we have been advised of the

possibility of such damages.

This warranty is in lieu of all other warranties express or

implied, including, but not limited to, the implied warran-

ties of merchantability or fitness for a particular purpose.

EXCLUSION OF DAMAGES

NECTECH' s liability for any defective product is limited

to the repair or replacement of the product at our option.

NECTECH shall not be liable for:

1. Damage to other property caused by any defects in this

product, damages based upon inconvenience, loss of

use of the product, loss of time, commercial loss; or

2. Any other damages whether incidental, consequential

or otherwise. Some states do not allow limitation on

how long an implied warranty lasts and/or do not al-

low the exclusion or limitation of incidental or conse-

quential damages, so the above limitations and exclu-

sions may not apply to you.

HOW STATE LAW RELATES TO THE WARRANTY

This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

FOR MORE INFORMATION, TELEPHONE 800-836-

0655

NEC TECHNOLOGIES, INC.

1250 N. Arlington Heights Road, Suite 500

Itasca, Illinois 60143-1248

Note:

All products returned to NECTECH for service

MUST have prior approval. To get approval, call NEC

Technologies at 800-836-0655.

Limited Warranty Plasma Monitors

Contents

How to Attach Options to the Plasma Monitor

......... 1

Introduction ..................................................... 2

Introduction to the PlasmaSync 42MP1

Plasma Monitor ....................................................... 2

The features you'll enjoy include: .............................. 2

Contents of the Package ........................................... 2

Part Names and Function ................................. 3

Front View .............................................................. 3

Rear View / Terminal Board ..................................... 4

Remote Controller .................................................... 5

Battery Installation and Replacement ......................... 6

Using the wired remote control mode ........................ 7

Operating Range .................................................... 7

Handling the remote controller ................................. 7

Installation...................................................... 8

Connecting Your PC Or Macintosh Computer ............ 9

Connections with Equipment that has a Digital Interface

..... 9

Connecting Your Document Camera .......................... 9

Connecting Your VCR Or Laser Disc Player ................ 9

Connecting Your DVD Player .................................... 9

External Speaker Connections ................................ 10

Pin Assignments and Signal Levels

for 15 pin RGB (Analog) ..................................... 11

Pin Configuration and Signal

of the RGB 3 IN Connector (DVI Connector) ......... 11

Basic Operations ............................................ 12

POWER ................................................................ 12

To turn the unit ON and OFF: ................................... 12

VOLUME .............................................................. 12

To adjust the volume: ................................................ 12

MUTE ................................................................... 12

To cancel the sound:.................................................. 12

DISPLAY ................................................................ 12

To check the settings: ................................................ 12

DIGITAL ZOOM .................................................... 12

OFF TIMER............................................................ 13

To set the off timer:................................................... 13

To check the remaining time:.................................... 13

Canceling the off timer ............................................. 13

WIDE Operations ............................................ 14

Watching with a wide screen (manual).................... 14

When watching videos or high definition

laser discs .................................................................. 14

Watching computer images with a wide screen ........ 15

OSM Controls ................................................. 16

Menu Operations .................................................. 16

Picture Settings Menu ............................................. 18

Adjusting the picture................................................. 18

Setting the picture mode according to the

brightness of the room .............................................. 19

Setting the color temperature ....................................20

Adjusting the color to the desired quality ................. 21

Reducting noise in the picture .................................. 22

Sound settings menu .............................................. 23

Adjusting the treble, bass and left/right balance ....... 23

Screen Settings Menu............................................. 24

Adjusting the Position, Size, Fine Picture,

Picture Adj ................................................................24

Function Settings Menu .......................................... 25

Setting the on-screen display ....................................25

Adjusting the position of the menu display .............. 26

Setting the power management for computer images

....... 27

POWER/STANDBY indicator.................................. 28

Setting the gray level for the sides of the screen.......29

Setting the brightness level to the minimum............. 29

Setting the picture to suit the movie .........................30

Resetting to the default values ..................................30

Option setting menu .............................................. 31

Setting the allocation of the audio connectors ..........31

Setting the BNC connectors......................................31

Setting a computer image to the correct RGB

select screen ..............................................................32

Setting high definition image to the suitable

screen size ............................................................... 33

Adjusting the display position

in the RGB3 input mode ......................................... 33

Information Menu .................................................. 34

Checking the frequencies and polarities

of input signals .......................................................... 34

Setting the language for the menus ........................... 34

Setting the video signal format ................................. 35

External Control ............................................ 36

Table for Signals Supported............................ 44

Supported resolutions ............................................ 44

Troubleshooting ............................................. 45

Specifications ................................................. 46

How to Attach Options to the Plasma Monitor

Drawing A

Drawing B

(1.22")

1110

(43.7")

748

(29.5")

(1.22")

(2") 50

(2")

Wall

Ventilation Requirements for

enclosure mounting

To allow heat to disperse, leave space between

surrounding objects as shown on the diagram be-

low when installing.

You can attach your optional mounts or stand to the plasma

monitor in one of the following two ways:

* While it is upright. (See Drawing A)

* As it is laid down with the screen face down (See Draw-

ing B). Lay the protective sheet, which was wrapped

around the monitor when it was packaged, beneath the

screen surface so as not to scratch the screen face.

• This device cannot be installed on its own.

Be sure to use a stand or original mounting

unit. (Wall mount unit, Stand, etc)

* See page 2.

• For correct installation and mounting it is

strongly recommended to use a trained,

authorized NEC dealer.

Failure to follow correct mounting proce-

dures could result in damage to the equip-

ment or injury to the installer.

Product warranty does not cover damage

caused by improper installation.

Introduction

Introduction to the PlasmaSync 42MP1

Plasma Monitor

NEC's PlasmaSync™ is a seamless blend of cutting-edge

visual technology and sophisticated design. At 42-inches,

with a 16:9 aspect ratio, the PlasmaSync 42MP1 certainly

makes a big impression. However, at a mere 3.5 inches/

89mm thin, the monitor's sleek techno-art lines blend in

well with your environment. PlasmaSync's crisp, vivid im-

age quality will transform data from any graphic medium

from PCs to DVD players- into art. And weighing only

70.6 lbs/ 32 kg, it actually can be hung almost anywhere.

NEC has made sure that a host of multimedia resources

can be easily connected and displayed as brilliantly as in-

tended on the PlasmaSync™ monitor.

The features you'll enjoy include:

• 42-inch screen

• 16:9 aspect ratio

• Capsulated Color Filter (CCF) and black matrix

• 3.5 inch / 89 mm thin

• 70.6 lbs/ 32 kg light

• High-resolution screen: 8532480 pixels

• 160-degrees of off-axis viewing, horizontally and verti-

cally.

• Flicker - and warp - free display provides excellent im-

age geometry even in screen corners

• Not affected by magnetic fields, no color drift or edge

distortion.

• VGA, SVGA, XGA, SXGA(60Hz), computer signal

compatibility

• NTSC, PAL, SECAM, composite and S-Video signal

compatibility

• 480P, 1080I, 720P and HDTV signal compatibility

• PCs, VCRs, Laser Disc and DVD player source compat-

ibility

• AccuBlend™ scan conversion automatically converts

VGA, SVGA and SXGA signals to the panel's native

resolution

• RGB input (3*), Video input (3), DVD/HD input (2*),

Audio input (3), External Control input (1)

• AccuColor control system provides user selectable on-

screen color temperature settings

• New Drive Technology

• Component video input terminal for DVD, 15.75kHz (Y,

CB, CR)

• NEC's OSM™ menu-driven on screen control system

that makes image adjustments a snap

• Seven languages (English, German, French, Italian, Span-

ish, Swedish, and Japanese)

* You can select RGB source or Component source for

the 5BNC terminal. When selecting an RGB input, the

source is switched to the RGB input (3); when selecting

a component input, the source is switched to the DVD/

HD input (2).

Contents of the Package

M PlasmaSync™ 42MP1 plasma monitor

M Power cord

M RGB cable (Mini D-Sub 15-pin to Mini D-Sub 15-

pin connector)

M Adapter for Macintosh

M Remote control unit with two AAA Batteries

M User's manual

M Wired Remote cable

M Safety metal fitting*

M Screw for safety metal fitting*

M Ferrite core (small22, large21)

* These are fittings for fastening the unit to a wall to

prevent tipping due to external shock when using the

stand (option). Fasten the safety fittings to the holes

in the back of the monitor using the safety fitting

mount screws.

Options

• Wall mount unit

• Ceiling mount unit

• Tilt mount unit

• Tabletop stand

• Speakers

• Others

Part Names and Function

Front View

INPUT SELECT VOLUME

POWER/STANDBY

PROCEED

POWER/STANDBY

DOWN LEFT/– RIGHT/+UP

VOLUME

/EXIT

INPUT SELECT

1 PROCEED

Sets the on-screen display (OSM) mode and displays

the main menu.

2 VOLUME Down and Up

Adjust the volume. Functions as the CURSOR (▲/▼)

buttons in the On-screen display (OSM) mode.

3 LEFT/– and RIGHT/+

Enlarges or reduces the image. Functions as the

CURSOR (§ / ©) buttons in the On-screen display

(OSM) mode.

4 INPUT SELECT / EXIT

Switches the input, in the following order:

VIDEO1

→→

VIDEO2

RGB3

←

RGB2

←

RGB1

→

VIDEO3 DVD/HD

→

←

Functions as the EXIT buttons in the On-screen display

(OSM) mode.

5 POWER/STANDBY indicator

When the power is on.............................Lights green.

When the power is in the standby mode ... Lights red.

6 Power

Turns the monitor's power on and off.

7 Remote sensor window

Receives the signals from the remote control unit.

Rear View/ Terminal Board

SPEAKERS MUST

HAVE MORE THAN

7WATT RATING

IMPEDANCE 6 OHM

LEFT

EXTERNAL

CONTROL

REMOTE

CONTROL

LOCK

ON/ OFF

AC IN

RIGHT

RGB 3

(Digital RGB)

RGB 1

R/CR/PR

G/Y

B/CB/PB

L(MONO)

CB/CR

PB/PR

L(MONO)

AUDIO 3 AUDIO 2 AUDIO 1 RGB2/ DVD2/ HD2

VIDEO 1

VIDEO 2

VIDEO 3

SPEAKERS MUST

HAVE MORE THAN

7WATT RATING

IMPEDANCE 6 OHM

LEFT

EXTERNAL

CONTROL

REMOTE

CONTROL

LOCK

ON/ OFF

AC IN

RIGHT

RGB 3

(Digital RGB)

RGB 1

R/C

G/Y

B/C

L(MONO)

AUDIO 3 AUDIO 2 AUDIO 1 RGB2/ DVD2/ HD2

VIDEO 1

VIDEO 2

VIDEO 3

A EXT SPEAKER L and R

Connect speakers here.

B EXTERNAL CONTROL

This terminal is used when power ON/OFF, input se-

lection and AUDIO MUTE and other controls are oper-

ated externally (by external control). See also page 36

for external control.

C REMOTE CONTROL

Connect the supplied remote cable here.

D CONTROL LOCK

When “CONTROL LOCK” is set “ON”, the buttons on

the set's control panel do not function.

E AC IN

Connect the included power cord here.

F RGB3 (DVI 29pin)

Inputs a digital RGB signal (TMDS).

G RGB1

Inputs the analog RGB signal of personal computer, etc.

H RGB2/ DVD2/ HD2

RGB2: Inputs the analog RGB signal.

DVD2/ HD2: Connect DVD's, high definition Laser

Discs, etc. here.

I VIDEO1, 2, 3

Connect VCR's, DVD's or LaserDiscs, etc. here.

J DVD1 / HD1

Connect DVD's high definition LaserDiscs, etc. here.

K AUDIO1, AUDIO2, AUDIO3

These are audio input terminals.

The input is selectable. Set which video image to allot

them to on the menu screen.

Remote Controller

1 POWER ON/OFF

Switches power on/off.

(This does not operate when POWER/STAND BY

indicator of the main unit is off.

OFF

POWER

RGB/PC DVD/HD

VIDEO

EXIT

POINTER

ZOOM

–

VOLUME

MUTE

WIDE

DISPLAY

OFF TIMER

REMOTE CONTROLLER

RD-337

PROCEED

POSITION

/CONTROL

–

2 RGB/PC

Press this button to select RGB/PC as the source.

→ RGB1 → RGB2 → RGB3 

RGB/PC can also be selected using the INPUT SELECT

button on the monitor. The input switches as follows

each time the button is pressed:

VIDEO1

→→

VIDEO2

RGB3

←

RGB2

←

RGB1

→

VIDEO3 DVD/HD

→

←

3 VIDEO

Press this button to select VIDEO as the source.

→ VIDEO1 → VIDEO2 → VIDEO3 

VIDEO can also be selected using the INPUT SELECT

button on the monitor. The input switches as follows

each time the button is pressed:

VIDEO1

→→

VIDEO2

RGB3

←

RGB2

←

RGB1

→

VIDEO3 DVD/HD

→

←

4 DVD / HD

Press this button to select DVD/HD as the source.

DVD/HD can also be selected using the INPUT SE-

LECT button on the monitor. The input switches as fol-

lows each time the button is pressed:

VIDEO1

→→

VIDEO2

RGB3

←

RGB2

←

RGB1

→

VIDEO3 DVD/HD

→

←

5 PROCEED

Press this button to access the OSM controls.

Press this button during the display of the main menu to

go to the sub menu.

6 EXIT

Press this button to exit the OSM controls in the main

menu. Press this button during the display of the sub

menu to return to the main menu.

7 CURSOR (▲ / ▼ /

)

Use these buttons to select items or settings and to ad-

just settings.

8 POINTER

Press this button to display the pointer.

9 VOLUME (+ /–)

Adjust the volume.

0 ZOOM (+ /–)

Enlarges or reduces the image

A MUTE

Mutes the sound.

B WIDE

The type of broadcast is detected automatically, and the

recommended wide screen mode is set.

C DISPLAY

Displays the source settings on the screen.

D OFF TIMER

Activates the off timer for the unit.

E Remote Jack

Insert the plug of the supplied remote cable when using

the supplied remote control unit in the wired condition.

F Remote control signal transmitter

Transmits the remote control signals.

Battery Installation and Replacement

Insert the 2 "AAA" batteries, making sure to set them in

with the proper polarity.

1.Press and open the cover.

2.Align the batteries according to the (+) and (–) indication

inside the case.

3.Replace the cover.

SPEAKERS MUST

HAVE MORE THAN

7WATT RATING

IMPEDANCE 6 OHM

LEFT

EXTERNAL

CONTROL

REMOTE

CONTROL

LOCK

ON/ OFF

AC IN

RIGHT

REMOTE

CONTROL

EXTERNAL

CONTROL

LOCK

ON/ OFF

Using the wired remote control mode

Connect the included remote control cable to the remote

control unit's "REMOTE CONTROL" terminal.

When the cable is connected, the mode automatically

switches to wired remote control.

When the wired remote control mode is used, the remote

control unit can be operated even if no batteries are loaded.

Remote Control Cable

To Remote Jack

POWER/STANDBY

VOLUME

DOWN UP

INPUT SELECT

/EXITLEFT/– RIGHT/+

30˚

Approx.

7m/ 23ft

Operating Range

* Use the remote controller within a distance of about 7 m

/ 23ft. from the front of the monitor's remote control sen-

sor and at a horizontal angle of within 30°.

* The remote control operation may not function if the

monitor's remote control sensor is exposed to direct sun-

light or strong artificial light, or if there is an obstacle

between the sensor and the remote control unit.

Handling the remote controller

• Do not drop or mishandle the remote control unit.

• Do not get the remote control unit wet. If the remote

gets wet, wipe it dry immediately.

• Avoid heat and humidity.

• When not using the remote control unit for a long pe-

riod, remove the batteries.

• Do not use new and old batteries together, or use differ-

ent types together.

• Do not take apart the batteries, heat them, or throw them

into a fire.

• When using the remote control unit in the wireless con-

dition, be sure to unplug the remote cable from the RE-

MOTE CONTROL terminal on the monitor.

RGB 3

(Digital RGB)

RGB 1

R/C

G/Y

B/C

L(MONO)

AUDIO 3 AUDIO 2 AUDIO 1 RGB2/ DVD2/ HD2

DVD1/HD1

VIDEO 1

VIDEO 2

VIDEO 3

Installation

Document Camera

VCR or Laser Disc Player

DVD Player

Signal cable (supplied)

To Mini D-Sub 15 pin connector on the plasma monitor

Monitor adapter for

Macintosh (supplied)

IBM VGA or Compatibles

Macintosh or Compatibles

(Desk top type)

To video, S-video inputs on

the plasma monitor

Personal computer with a

digital RGB output

Connecting Your PC Or Macintosh Computer

Connecting your PC or Macintosh computer to your plasma moni-

tor will enable you to display your computer's screen image for an

impressive presentation. The plasma monitor supports the signals

described on page 44.

To connect to a PC, Macintosh or compatible graphics adapter,

simply:

1. Turn off the power to your plasma monitor and computer.

2. If your PC does not support XGA/SVGA/VGA you will need

to install an XGA/SVGA/VGA graphics board. Consult your

computer's owner's manual for your XGA/SVGA/VGA con-

figuration. If you need to install a new board, see the manual

that comes with your new graphics board for installation in-

structions.

3. The plasma monitor provides signal compatibility up to VESA

128021024@60Hz (SXGA). However, it is not recom-

mended to use this resolution due to image readability on the

monitors 8532480 native pixel resolution panel.

4. Use the signal cable that's supplied to connect your PC or

Macintosh computer to the plasma monitor. For Macintosh,

use the supplied monitor adapter to connect to your computer's

video port.

5. Turn on the plasma monitor and the computer.

6. If the plasma monitor goes blank after a period of inactivity, it

may be caused by a screen saver installed on the computer

you've connected to the plasma monitor.

When using a Macintosh with the plasma monitor, the following

four display standards are supported using the included Macintosh

adapter :

13" fixed mode

16" fixed mode

19" fixed mode

21" fixed mode

The 13" fixed mode is recommended for the plasma monitor.

Connections with Equipment that has

a Digital Interface

Connections can be made with equipment that is equipped with

a digital interface compliant with the DVI (Digital Visual

Interface) standard.

* Use a DVI 29-pin signal cable (available separately) and the

ferrite cores (supplied) when making connections to the RGB3

IN (DVI) connector of the main unit.

Note that the RGB3 IN(DVI) terminal does not support analog

RGB input source.

Note:

1. Input TMDS signals conforming to DVI standards.

The TMDS input corresponds to 1 link.

2.To maintain display quality, use a cable with a quality

prescribed by DVI standards that is within 5 meters in length.

Connecting Your Document Camera

You can connect your plasma monitor to a document camera. To

do so, simply:

1. Turn off the power to your plasma monitor and document

camera.

2. Use a standard video cable to connect your document camera

to the Video input on your plasma monitor.

3. Turn on the plasma monitor and the document camera.

Note:

Refer to your document camera's owner's manual for

more information about your camera's video output

requirements.

Connecting Your VCR Or Laser Disc

Player

Use common RCA cables (not provided) to connect your VCR

or laser disc player to your plasma monitor. To make these

connections, simply:

1. Turn off the power to your plasma monitor and VCR or laser

disc player.

2. Connect one end of your RCA cable to the video output

connector on the back of your VCR or laser disc player,

connect the other end to the Video input on your plasma

monitor. Use standard RCA audio patch cords to connect the

audio from your VCR or laser disc player to your plasma

monitor (if your VCR or laser disc player has this capability).

Be careful to keep your right and left channel connections

correct for stereo sound.

3. Turn on the plasma monitor and the VCR or laser disc player.

Note:

Refer to your VCR or laser disc player owner's manual

for more information about your equipment's video output

requirements.

Connecting Your DVD Player

You can connect your plasma monitor to a DVD player. To do so,

simply:

1. Turn off the power to your plasma monitor and DVD player.

2. Use a standard video cable to connect your DVD player to

the Y, Cb, and Cr inputs on your plasma monitor.

Or use the DVD-player's S-Video output. Use a standard S-

Video cable to connect to the S-Video input on the plasma

monitor.

3. Turn on the plasma monitor and the DVD player.

External Speaker Connections

External speakers may be connected to the plasma monitor

to reproduce sound from VIDEO, DVD or RGB signal

sources.

External speakers may be connected directly to the SPEAK-

ERS terminals or indirectly by connecting a stereo system

amplifier to the audio outputs.

CAUTION:

Unplug the plasma monitor and all con-

nected components before connecting external speak-

ers. Use only speakers with 6-ohm impedance and a

power output rating of 7 watts or more.

To connect external speakers directly to the plasma monitor:

1. Strip the ends of the speaker wires.

2. Press down the tabs below the SPEAKERS terminals,

insert the speaker wire and release the tab to secure the

speaker wire connection:

[a] Connect the right speaker (located at right side

of the monitor when viewed from the front)

positive (+) wire to RIGHT +.

[b] Connect the right speaker negative (–) wire to

RIGHT -.

[c] Connect the left speaker negative (–) wire to

LEFT–.

[d] Connect the left speaker positive wire (+) to

LEFT+.

SPEAKERS MUST

HAVE MORE THAN

7WATT RATING

IMPEDANCE 6 OHM

LEFT

EXTERNAL

CONTROL

REMOTE

CONTROL

LOCK

ON/ OFF

AC IN

RIGHT

RGB 3

(Digital RGB)

RGB 1

R/CR/PR

G/Y

B/CB/PB

L(MONO)

CB/CR

PB/PR

L(MONO)

AUDIO 3 AUDIO 2 AUDIO 1 RGB2/ DVD2/ HD2

VIDEO 1

VIDEO 2

VIDEO 3

RIGHT

LEFT

Pin Assignments and Signal Levels for 15 pin RGB (Analog)

5 4 3 2 1

15 14 13 12 11

10 9 8 7 6

Pin No.

Signal (Analog)

Red

Green or sync-on-green

Blue

No connection

Ground

Red ground

Green ground

Blue ground

No connection

Sync signal ground

No connection

Bi-directional DATA (SDA)

Horizontal sync

Vertical sync

SCL

Pin Configuration and Signal of the RGB 3 IN Connector (DVI Connector)

Pin No.

Signal (Digital)

T.M.D.S Data 2 -

T.M.D.S Data 2 +

T.M.D.S Data 2 Shield

No connection

DDC Clock

DDC Data

No connection

T.M.D.S Data 1 -

T.M.D.S Data 1 +

T.M.D.S Data 1 Shield

No connection

+5V Power

Ground

Hot Plug Detect

T.M.D.S Data 0 -

T.M.D.S Data 0 +

T.M.D.S Data 0 Shield

No connection

T.M.D.S Clock Shield

T.M.D.S Clock +

T.M.D.S Clock -

No connection

RGB 3

The unit is equipped with a type of connector commonly

used for both analog and digital.

(Functionally, this cannot be used for analog input.)

(TMDS can be used for one link only)

8 25 26

27 28

Basic Operations

POWER

To turn the unit ON and OFF:

1. Plug the power cord into an active AC power outlet.

2. Press the POWER ON button (on the remote control-

ler) to turn on.

The monitor’s POWER/STANDBY indicator will light

up(green) when the unit is on.

3. Press the POWER OFF button (on the remote control-

ler or the unit) to turn off.

The monitor’s POWER/STANDBY indicator turns red

and the standby mode is set (only when turning off the

unit with the remote control).

VOLUME

To adjust the volume:

1. Press and hold the VOLUME ▲ button (on the remote

controller or the unit) to increase to the desired level.

2. Press and hold the VOLUME ▼ button (on the remote

controller or the unit) to decrease to the desired level.

MUTE

To cancel the sound:

Press the MUTE button on the remote controller to cancel

sound; press again to restore.

DISPLAY

To check the settings:

1. The screen changes each time the DISPLAY button is

pressed.

2. If the button is not pressed for approximately three sec-

onds, the menu turns off.

DIGITAL ZOOM

Digital zoom specifies the picture position and enlarges

the picture.

1. Press the pointer button to display the pointer. ( )

To change the size of the picture:

Press the ZOOM+ button and enlarge the picture.

The pointer will change to resemble a magnifying

glass. ( )

A press of the ZOOM- button will reduce the picture

and return it to its original size.

To change the picture position:

2. Press the pointer button to delete the pointer.

OFF TIMER

To set the off timer:

The off timer can be set to turn the power off after 30,

60, 90 or 120 minutes.

1. Press the OFF TIMER button to start the timer at 30

minutes.

2. Press the OFF TIMER button to the desired time.

3. The timer starts when the menu turns off.

→ 30 → 60 → 90 → 120 → 0 

To check the remaining time:

1. Once the off timer has been set, press the OFF TIMER

button once.

2. The remaining time is displayed, then turns off after a

few seconds.

3. When five minutes remain the remaining time appears

until it reaches zero.

OFF TIMER30

OFF TIMER28

OFF TIMER0

Canceling the off timer

1. Press the OFF TIMER button twice in a row.

2. The off timer is canceled.

Note:

After the power is turned off with the off timer ...

A slight current is still supplied to the monitor. When

you are leaving the room or do not plan to use the sys-

tem for a long period of time, turn off the power of the

monitor.

La page charge ...

NEC PlasmaSync® 42VM1 Le manuel du propriétaire

Marque: NEC

Modèle: PlasmaSync® 42VM1

Catégorie: Téléviseurs

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: NEC PlasmaSync® 42VM1 Owner's manual

NEC PlasmaSync® 42VM1 Le manuel du propriétaire

NEC PlasmaSync® 42VM1 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents