Pioneer Flat Panel Television PDP-42MVE1 Manuel utilisateur

Operating Instructions

Mode d’emploi

Bedienungsanleitung

Istruzioni per l’utilizzo

Manual de instrucciones

Инструкция по эксплуатации

Gebruiksaanwijzing

PLASMA DISPLAY

ÉCRAN À PLASMA

PLASMA-DISPLAY

DISPLAY A PLASMA

PANTALLA DE PLASMA

ПЛАЗМЕННЫЙ ДИСПЛЕЙ

PLASMASCHERM

PDP-42MVE1

English

En

Operating Instructions

Thank you very much for purchasing this PIONEER product.

Before using your Plasma Display, please carefully read the

“Important Information” and these “Operating Instructions” so

you will know how to operate the Plasma Display properly.

Keep this manual in a safe place. You will find it useful in the

future.

Note for Dealers:

After installation, be sure to deliver this manual to the customer

and explain to the customer how to handle the product.

Notes on Installation Work:

This product is marketed assuming that it is installed by qualified

personnel with enough skill and competence. Always have an

installation specialist or your dealer install and set up the product.

PIONEER cannot assume liabilities for damage caused by mistake

in installation or mouting, misuse, modification or a natural disaster.

English

Important Information

2

En

i

En

Precautions

Please read this manual carefully before using your plasma

monitor and keep the manual handy for future reference.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER. NO

USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

This symbol warns the user that uninsulated

voltage within the unit may have sufficient

magnitude to cause electric shock.

Therefore, it is dangerous to make any kind

of contact with any part inside of this unit.

This symbol alerts the user that important

literature concerning the operation and

maintenance of this unit has been included.

Therefore, it should be read carefully in

order to avoid any problems.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE

THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE

THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD

RECEPTACLE OR OTHER OUTLETS, UNLESS THE

PRONGS CAN BE FULLY INSERTED. REFRAIN FROM

OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE

COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

Important Information

Warnings and Safety Precaution

This plasma monitor is designed and

manufactured to provide long, trouble-free service.

No maintenance other than cleaning is required.

Please see the section “Plasma monitor cleaning

procedure” on the next page.

The plasma display panel consists of fine picture

elements (cells) with more than 99.99 percent active

cells. There may be some cells that do not produce

light or remain lit.

For operating safety and to avoid damage to the unit,

read carefully and observe the following instructions.

To avoid shock and fire hazards:

1. Provide adequate space for ventilation to avoid internal

heat build-up. Do not cover rear vents or install the unit

in a closed cabinet or shelves.

If you install the unit in an enclosure, make sure there

is adequate space at the top of the unit to allow hot air

to rise and escape. If the monitor becomes too hot, the

overheat protector will be activated and the monitor will

be turned off. If this happens, turn off the power to the

monitor and unplug the power cord. If the room where

the monitor is installed is particularly hot, move the

monitor to a cooler location, and wait for 60 minutes to

cool the monitor. If the problem persists, contact your

dealer for service.

2. Do not use this unit’s polarized plug with extension cords

or outlets unless the prongs can be completely inserted.

3. Do not expose the unit to water or moisture.

4. Avoid damage to the power cord, and do not attempt to

modify the power cord.

5. Unplug the power cord during electrical storms or if

the unit will not be used over a long period.

6. Do not open the cabinet which has potentially dangerous

high voltage components inside. If the unit is damaged in

this way the warranty will be void. Moreover, there is a

serious risk of electric shock.

7. Do not attempt to service or repair the unit. The

manufacturer is not liable for any bodily harm or damage

caused if unqualified persons attempt service or open

the back cover. Refer all service to authorized Service

Centers.

English

Important Information

3

En

ii

En

To avoid damage and prolong operating life:

1. Use only with 100-240 V 50/60Hz AC power supply.

Continued operation at line voltages greater than 100-

240 Volts AC will shorten the life of the unit, and might

even cause a fire hazard.

2. Handle the unit carefully when installing it and do not

drop.

3. Set the unit away from heat, excessive dust, and direct

sunlight.

4. Protect the inside of the unit from liquids and small

metal objects. In case of accident, unplug the power

cord and have it serviced by an authorized Service

Center.

5. Do not hit or scratch the panel surface as this causes

flaws on the surface of the screen.

6. For correct installation and mounting it is strongly

recommended to use a trained, authorized dealer.

7. As is the case with any phosphor-based display (like a

CRT monitor, for example) light output will gradually

decrease over the life of a Plasma Display Panel.

8. To avoid sulfurization it is strongly recommended not to

place the unit in a dressing room in a public bath or hot

spring bath.

9. Do not use in a moving vehicle, as the unit could drop or

topple over and cause injuries.

10. Do not place the unit on its side, upside-down or with the

screen facing up or down, to avoid combustion or electric

shock.

Plasma monitor cleaning procedure:

1. Use a wiping cloth (attached) or a soft dry cloth to clean

the front panel and bezel area. Never use solvents such as

alcohol or thinner to clean these surfaces.

2. Clean plasma ventilation areas with a vacuum cleaner

with a soft brush nozzle attachment.

3. To ensure proper ventilation, cleaning of the ventilation

areas must be carried out monthly. More frequent cleaning

may be necessary depending on the environment in which

the plasma monitor is installed.

Recommendations to avoid or minimize phosphor burn-in:

Like all phosphor-based display devices and all other gas

plasma displays, plasma monitors can be susceptible to

phosphor burn under certain circumstances. Certain

operating conditions, such as the continuous display of a

static image over a prolonged period of time, can result in

phosphor burn if proper precautions are not taken. To protect

your investment in this plasma monitor, please adhere to the

following guidelines and recommendations for minimizing

the occurrence of image burn:

* Always enable and use your computer’s screen saver

function during use with a computer input source.

* Display a moving image whenever possible.

* Change the position of the menu display from time to time.

* Always power down the monitor when you are finished

using it.

If the plasma monitor is in long term use or continuous

operation take the following measures to reduce the

likelihood of phosphor burn:

* Lower the Brightness and Contrast levels as much as

possible without impairing image readability.

* Display an image with many colors and color gradations

(i.e. photographic or photo-realistic images).

* Create image content with minimal contrast between light

and dark areas, for example white characters on black

backgrounds. Use complementary or pastel color whenever

possible.

* Avoid displaying images with few colors and distinct,

sharply defined borders between colors.

*

Note:

Burn-in is not covered by the warranty.

Contact your dealer for other recommended procedures that

will best suit your particular application needs.

CAUTION:

WHEN POSITIONING THIS EQUIPMENT ENSURE THAT

THE MAINS PLUG AND SOCKET IS EASILY ACCES-

SIBLE.

NOTE:

When you connect a computer to this monitor, use an RGB

cable including the ferrite core on both ends of the cable.

And regarding DVI and power cable, attach the supplied

ferrite cores. If you do not do this, this monitor will not

conform to mandatory CE or C-Tick standards.

Attaching the ferrite cores:

Set the ferrite cores on both ends of the DVI cable (not

supplied), and both ends of the power cable (supplied).

Close the lid tightly until the clamps click.

Use the band to fasten the ferrite core (supplied) to the

DVI cable.

DVI cable (not supplied)

core (small)

Connector

band

Power cable (supplied)

core (large)

English

Important Information

4

En

iii

En

This product complies with the Low Voltage Directive

(73/23/EEC, amended by 93/68/EEC), EMC Directives

(89/336/EEC, amended by 92/31/EEC and 93/68/EEC).

Caution

This model is for use with the following optional accessories.

Use with other optional accessories is capable of resulting in

instability causing possible injury.

Speakers: PDP-S32-LR

Table top stand: PDK-TS09

Wall mount unit: PDK-WM04

Tilt mount unit: PDK-WT01

Ceiling mount unit: PDK-CK01

English

Contents

1

En

Contents

Contents of the Package

 Plasma monitor

 Power cord

 Remote control with two AAA Batteries

 Manual

 Warranty

 Safety metal fittings (2pcs)

*

 Ferrite cores (large 2pcs, small 2pcs)

 Bands (2pcs)

 Wiping cloth

* These are fittings for fastening the unit to a wall to prevent

tipping due to external shock when using the stand

(optional). Fasten the safety fittings to the holes in the

back of the monitor using the safety fitting mount screws

(see page 2).

Options

• Stand

• Speakers

• Wall mount unit

• Tilt mount unit

• Ceiling mount unit

Installation ...................................................... 2

Ventilation Requirements for enclosure mounting .......... 2

How to use the safety metal fittings and the screws for

safety metal fittings ................................................ 2

Creating a video wall ............................................... 3

Cable Management.................................................. 3

Caution on when the plasma monitor is installed vertically ...

4

How to use the remote control.................................... 4

Battery Installation and Replacement ........................... 4

Using the wired remote control mode .......................... 4

Operating Range .......................................................... 4

Handling the remote control ......................................... 4

Part Names and Function .................................. 5

Front View .............................................................. 5

Rear View/ Terminal Board ....................................... 6

Remote Control ........................................................ 7

Basic Operations ............................................... 8

POWER .................................................................. 8

To turn the unit ON and OFF: ...................................... 8

VOLUME ................................................................ 8

To adjust the sound volume: ......................................... 8

MUTING ................................................................. 8

To mute the sound: ....................................................... 8

DISPLAY .................................................................. 8

To check the settings: ................................................... 8

DIGITAL ZOOM ....................................................... 8

AUTO SET UP .......................................................... 8

To adjust the size or quality of the picture automatically: ......

8

OFF TIMER .............................................................. 8

To set the off timer: ...................................................... 8

To check the remaining time: ....................................... 8

To cancel the off timer: ................................................ 8

WIDE Operations ............................................... 9

SCREEN SIZE Operation (manual) ............................. 9

When viewing videos or digital video discs ................. 9

SCREEN SIZE Operation with Computer Signals ........ 10

OSD (On Screen Display) Controls ..................... 11

Menu Operations ................................................... 11

Setting the language for the menus ........................... 11

Menu Tree ............................................................. 12

Picture Settings Menu.............................................. 14

Adjusting the picture .................................................. 14

Setting the picture modes according to the brightness of

the room .................................................................. 14

Reducing noise in the picture ..................................... 14

Setting the color temperature ..................................... 14

Adjusting the color to the desired level ...................... 15

Changing the Gamma Curve ...................................... 15

Making the Low Tone adjustments............................. 15

Adjusting the colors ................................................... 15

SOUND Settings Menu ........................................... 16

Adjusting the treble, bass and left/right balance and audio

input select .............................................................. 16

Setting the allocation of the audio connectors ............ 16

SCREEN Settings Menu ........................................... 16

Adjusting the Position, Size, PHASE, CLOCK .......... 16

Option1 Settings Menu ........................................... 17

Setting the on-screen display ...................................... 17

Setting the PC2/COMPONENT2 connectors ............. 17

Setting the PC1 connector .......................................... 17

Setting a computer image to the correct RGB select screen ......

18

Setting high definition images to the suitable screen size ....

18

Setting the Input Skip ................................................. 18

Resetting to the default values .................................... 18

Option2 Settings Menu ........................................... 19

Setting the power management for computer images . 19

STANDBY/ON indicator ........................................... 19

Setting the picture to suit the movie ........................... 19

Reducing burn-in of the screen .................................. 19

Setting the gray level for the SIDE MASK ................. 21

Setting the screen size for S1/S2 video input .............. 22

Setting the signal and black level for DVI signal ........ 22

Option3 Settings Menu ........................................... 22

Using the timer .......................................................... 22

Setting the power on mode ......................................... 23

Enabling/disabling the front panel controls ................ 23

Enabling/disabling remote control wireless transmission ....

24

Loop Out setting ........................................................ 24

ID number setting ...................................................... 24

Video Wall setting ...................................................... 24

Advanced OSD Settings Menu ................................. 27

Setting the menu mode .............................................. 27

Color System Settings Menu .................................... 27

Setting the video signal format ................................... 27

Source Information Menu ........................................ 27

Checking the frequencies, polarities of input signals, and

resolution ................................................................ 27

Pin Assignments ............................................. 28

mini D-Sub 15-pin connector (Analog) ..................... 28

DVI-D 24-pin connector (Digital) .............................. 28

Table of Signals Supported .............................. 29

Troubleshooting .............................................. 31

Specifications ................................................. 32

English

Installation

2

En

50

mm

(2")

50

mm

(2") 50

mm

(2")

Wall

50

mm

(2")

50

mm

(2")

You can attach your optional mounts or stand to the plasma monitor in one of the following two ways:

* While it is upright. (See Drawing A)

* As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the

monitor when it was packaged, beneath the screen surface so as not to scratch the screen face.

* Do not touch or hold the screen face when carrying the unit.

• This device cannot be installed on its own. Be sure to use a stand or original mounting unit. (Wall

mount unit, Stand, etc.)

* See page 1.

• For correct installation and mounting it is strongly recommended to use a trained, authorized

dealer.

Failure to follow correct mounting procedures could result in damage to the equipment or injury

to the installer.

Product warranty does not cover damage caused by improper installation.

* Use only the mounting kit or stand provided by manufacturer and listed under Options.

Drawing B

Drawing A

How to use the safety metal fittings

and the screws for safety metal

fittings

These are fittings for fastening the unit to a wall to prevent

tipping due to external shock when using the stand

(optional). Fasten the safety fittings to the holes in the

back of the monitor using the safety fitting mount screws.

Screw hole

Wall

Ta bl e Top

Safty metal fittings

Screw for Safty metal

fittings

Metal chain

(Not supplied)

Screw or Hook etc.

(Not supplied)

Ventilation Requirements for

enclosure mounting

To allow heat to disperse, leave space between surrounding

objects as shown on the diagram below when installing.

Installation

English

Installation

3

En

Note:

1. The VIDEO1 and PC1 terminals can be used for either INPUT or OUTPUT.

When LOOP OUT is ON, do not connect an OUTPUT signal from another unit, that will place an extraordinary load on

the other unit and may damage it.

2. LOOP OUT can not be turned ON while signals are input to the PC1 terminal.

3. LOOP OUT can be turned ON while signals are input to the PC1 terminal if the POWER is switched ON.

Information

• To loop signals out to another plasma display, set the LOOP OUT to ON.

• To create a video wall, set the VIDEO WALL menu items properly.

• To connect monitors, please use a 1~2m (3.3~6.6 feet) BNC cable (any commercially available cable).

• If the image quality is poor, do not use the monitor’s out terminal. Use a distribution amplifier (any commercially

available distribution amplifier) to connect the split signals to the respective monitor INPUT terminals.

• Being used as a video wall function, maximaly 4-screen is rough-standard with lower than 1024768, 60Hz

signal.

• A distribution amplifier is particularly recommended when using 9-screen and over video wall.

• From the second monitor onward, connections require a BNC-RCA conversion cable or connector, a mini D-Sub

15 pin cable-BNC (5) cable or a conversion connector.

Creating a video wall

With built-in matrix display capability, you can create a 4-25 video wall.

• Connect signal cables and remote cables as shown below.

Video signal PC/COMPONENT signal

BNC connector

RCA phono plug

OUT

VIDEO signal

IN

OUT

Remote

control

VIDEO signal

Remote

IN

control

BNC connector

PC signal/

IN

OUT

Remote

control

COMPONENT

signal

PC signal/

COMPONENT

signal

IN

Remote

control

Cable Management

Using the cable clamps provided with the plasma display,

bundle at the back of the unit the signal and audio cables

connected to the display.

Back of the unit

mounting hooks

To attach To detach

clamp

mounting hook

cables

1. 2.

English

Installation

4

En

OPTION1

RETURN

SEL. OK

:

RGB

:

RGB

:

AUTO

:

1080B

:

OFF

:

OFF

1024 768

EXIT

OSD

BNC INPUT

D-SUB INPUT

RGB SELECT

HD SELECT

INPUT SKIP

ALL RESET

MENU

Bottom side

Top side

Caution on when the plasma monitor is installed vertically

• Use the optional unit. Contact your store of purchase when installing.

• Rotate 90° clockwise as seen from the front when installing.

• After installing, check with the PIONEER logo mark

as seen from the front.

• Be sure to set “OSD ANGLE” to “V” when using.

* Failure to heed the above cautions may lead to malfunction.

How to use the remote control

Battery Installation and Replacement

Insert the 2 “AAA” batteries, making sure to set them in

with the proper polarity.

1.Press and open the cover.

2.Align the batteries according to the (+) and (–) indication

inside the case.

3.Replace the cover.

* The 1/8 Stereo Mini cable must be purchased separately.

Operating Range

* Use the remote control within a distance of about 7 m/

23ft. from the front of the monitor’s remote control sensor

and at horizontal and vertical angles of up to approximately

30°.

* The remote control operation may not function if the

monitor’s remote control sensor is exposed to direct

sunlight or strong artificial light, or if there is an obstacle

between the sensor and the remote control.

Handling the remote control

• Do not drop or mishandle the remote control.

• Do not get the remote control wet. If the remote control

gets wet, wipe it dry immediately.

• Avoid heat and humidity.

• When not using the remote control for a long period,

remove the batteries.

• Do not use new and old batteries together, or use different

types together.

• Do not take apart the batteries, heat them, or throw them

into a fire.

• When using the remote control in the wireless condition,

be sure to unplug the remote cable from the REMOTE

IN terminal on the monitor.

• When disposing of used batteries, please comply with

governmental regulations or environmental public

instruction’s rules that apply in your country/area.

Using the wired remote control mode

Connect the remote cable* to the remote control’s remote

jack and the “REMOTE IN” terminal on the monitor.

When the cable is connected, the mode automatically

switches to wired remote control. When the wired remote

control mode is used, the remote control can be operated

even if no batteries are loaded.

English

Part Names and Function

5

En

q Power ( )

Turns the monitor’s power on and off.

w Remote sensor window

Receives the signals from the remote control.

e STANDBY/ON indicator

When the power is on ............................. Lights green.

When the power is in the standby mode ... Lights red.

r INPUT/EXIT

Switches the input.

The available inputs depend on the setting of “BNC

INPUT”, “RGB SELECT”, “D-SUB SELECT” and

“DVI SET-UP”.

Functions as the EXIT buttons in the On-Screen

Display (OSD) mode.

Front View

456

7

1 3 2

t LEFT/– and RIGHT/+

Functions as the CURSOR (



/



) buttons in the On-

Screen Display (OSD) mode.

y VOLUME

and

Adjusts the volume. Functions as the CURSOR (▲/

▼) buttons in the On-Screen Display (OSD) mode.

u MENU/SET

Sets the On-Screen Display (OSD) mode and displays

the main menu.

WARNING

The Power on/off switch does not disconnect the plasma

display completely from the supply mains.

Part Names and Function

Note:

This plasma monitor has the capasity to display images when connected to European DVD players with a SCART

output signal, which is RGB with composite sync.

Your dealer can supply a special SCART cable, which will enable you to use the RGB with composite sync signal.

To obtain the special cable as well as for further information, please contact your dealer.

Please refer to page 19 for selection of the correct mode in the on-screen display.

English

Part Names and Function

6

En

A AC IN

Connect the included power cord here.

B EXT SPEAKER L and R

Connect speakers (optional) here. Maintain the correct

polarity. Connect the

(positive) speaker wire to the

EXT SPEAKER terminal and the (negative)

speaker wire to the

EXT SPEAKER terminal on

both LEFT and RIGHT channels.

Please refer to your speaker’s owner’s manual.

C VIDEO1, 2, 3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or Video Cameras, etc. here.

VIDEO1 can be used for Input or Output (see page

24).

D AUDIO1, AUDIO2, AUDIO3

These are audio input terminals.

The input is selectable. Set which video image to allot

them from the SOUND menu screen.

E COMPONENT1

Connect DVD’s, High Definition or Laser Discs, etc.

here.

F PC2/COMPONENT2

PC2: You can connect an analog RGB signal

and the syncronization signal.

COMPONENT2

: You can connect DVDs, High

Definition sources, Laser Discs, etc.

here.

This input can be set for use with an

RGB or component source (see page

17).

G PC1 (mini D-Sub 15pin)

Connect an analog RGB signal from a computer, etc.

here. This input can be used for Input or Output (see

page 24).

H PC3

(DVI 24pin)

Connect a digital signal (TMDS) from a source with a

DVI output.

I RS-232C

Never connect any component to this connector

without first consulting your Pioneer installation

technician.

This connector is used for plasma display setup

adjustments.

J REMOTE IN

Connect the remote cable* to the remote control’s

remote jack to obtain wired remote control.

K REMOTE OUT

Connect the remote cable* to the REMOTE IN jack of

the other display monitor to obtain wired remote

control.

Information

• For Y/CB/Cr, connect to the COMPONENT1 or PC2/

COMPONENT2 terminals.

• For SCART, this unit provides three ways to connect:

· SCART1: Connect R/G/B and composite sync. to

the PC2/COMPONENT2 terminals. (R, G, B and

HD connector)

· SCART2: Connect R/G/B to the COMPONENT2

terminals and composite sync. to the VIDEO1

terminal.

· SCART3: Connect R/G/B and composite sync. to

the PC1 terminal.

* The 1/8 Stereo Mini cable must be purchased separately.

Rear View/ Terminal Board

English

Part Names and Function

7

En

q POWER ON/STANDBY

Switches the power on/standby.

(This does not operate when STANDBY/ON indicator

of the main unit is off.)

w RGB/PC

Press this button to select RGB/PC as the source.

RGB/PC can also be selected using the INPUT/EXIT

button on the monitor.

e COMPONENT

Press this button to select COMPONENT as the source.

COMPONENT can also be selected using the INPUT/

EXIT button on the monitor.

r VIDEO

Press this button to select VIDEO as the source.

VIDEO can also be selected using the INPUT/EXIT

button on the monitor.

t MENU/SET

Press this button to access the OSD controls.

Press this button during the display of the main menu

to go to the sub menu.

y CURSOR (▲ / ▼ /



/



)

Use these buttons to select items or settings and to

adjust settings.

u EXIT

Press this button to exit the OSD controls in the main

menu. Press this button during the display of the sub

menu to return to the previous menu.

i POINT ZOOM

Press this button to display the pointer.

o ZOOM (+ /–)

Enlarges or reduces the image.

!0 VOLUME (+ /–)

Adjusts the sound volume.

!1 MUTING

Mutes the sound.

!2 SCREEN SIZE

Automatically detects the signal and sets the aspect ratio.

SCREEN SIZE button is not active for all signals.

!3 DISPLAY

Displays the source settings on the screen.

!4 OFF TIMER

Activates the off timer for the unit.

!5 AUTO SET UP

Press this button to adjust PHASE, CLOCK, Position,

and Contrast automatically, or to switch the screen size

to ZOOM mode automatically with the superimposed

caption displayed fully only when the picture contains

dark areas above and below the picture.

!6 ID NO. SET

Set the ID number in the remote control. The remote

control can then be used only for a display with the

same ID number. When several displays are used

together they can be controlled individually.

!7 CLEAR

Clears the number set by the ID NO. SET button.

!8 Remote control signal transmitter

Transmits the remote control signals.

!9 Remote Jack

Insert the plug of the remote cable (The 1/8 Stereo

Mini cable) here when using the supplied remote

control in the wired condition.

Remote Control

→ VIDEO1 → VIDEO2 → VIDEO3

English

Basic Operations

8

En

Basic Operations

POWER

To turn the unit ON and OFF:

1. Plug the power cord into an active AC power outlet.

2. Press the Power button (on the unit).

The monitor’s STANDBY/ON indicator turns red and the

standby mode is set.

3. Press the POWER ON button (on the remote control) to

turn on the unit.

The monitor’s STANDBY/ON indicator will light up

(green) when the unit is on.

4.

Press the POWER STANDBY button (on the remote control)

or the Power button (on the unit) to turn off the unit.

The monitor’s STANDBY/ON indicator turns red and the

standby mode is set (only when turning off the unit with

the remote control).

VOLUME

To adjust the sound volume:

1. Press and hold the VOLUME button (on the remote

control or the unit) to increase to the desired level.

2. Press and hold the VOLUME

button (on the remote

control or the unit) to decrease to the desired level.

MUTING

To mute the sound:

Press the MUTING button on the remote control to mute

the sound; press again to restore.

DISPLAY

To check the settings:

1. The screen changes each time the DISPLAY button is

pressed.

2. If the button is not pressed for approximately three seconds,

the menu turns off.

DIGITAL ZOOM

Digital zoom specifies the picture position and enlarges

the picture.

1. Press the POINT ZOOM button to display the pointer.

( )

To change the size of the picture:

Press the ZOOM+ button and enlarge the picture.

The pointer will change to resemble a magnifying glass.

(

)

A press of the ZOOM- button will reduce the picture

and return it to its original size.

To change the picture position:

Select the position with the ▲▼





buttons.

2. Press the POINT ZOOM button to delete the pointer.

AUTO SET UP

To adjust the size or quality of the picture

automatically:

Press the AUTO SET UP button.

Information

 AUTO SET UP ON setting

When RGB (still picture) input is selected:

PHASE, CLOCK, Position, and Contrast will be

adjusted automatically.

When RGB (motion picture), VIDEO, or Y/Pb/Pr

(component) input is selected:

The screen size switches to ZOOM mode automatically

with the superimposed caption displayed fully only

when the picture contains dark areas above and below

the picture.

OFF TIMER

To set the off timer:

The off timer can be set to turn the power off after 30, 60,

90 or 120 minutes.

1. Press the OFF TIMER button to start the timer at 30

minutes.

2. Press the OFF TIMER button to the desired time.

3. The timer starts when the menu turns off.

→ 30 → 60 → 90 → 120 → 0

OFF TIMER 30

To check the remaining time:

1. Once the off timer has been set, press the OFF TIMER

button once.

2. The remaining time is displayed, then turns off after a few

seconds.

3. When five minutes remain the remaining time appears

until it reaches zero.

OFF TIMER 28

To cancel the off timer:

1. Press the OFF TIMER button twice in a row.

2. The off timer is canceled.

OFF TIMER 0

Note:

After the power is turned off with the off timer ...

A slight current is still supplied to the monitor. When you

are leaving the room or do not plan to use the system for a

long period of time, turn off the power of the monitor.

English

WIDE Operations

9

En

SCREEN SIZE Operation

(manual)

With this function, you can select one of six screen sizes.

When viewing videos or digital video discs

1. Press the SCREEN SIZE button on the remote control.

2. Within 3 seconds ...

Press the SCREEN SIZE button again.

The screen size switches as follows:

→ 4:3 → FULL → WIDE → ZOOM → 2.35:1 → 14:9

When a 720P or 1080I signal is input:

FULL ↔ 2.35:1

4:3 size screen

The normal size screen is displayed.

* The picture has the same size as video pictures with a 4 : 3

aspect ratio.

FULL size screen

The image is expanded in the horizontal direction.

* Images compressed in the horizontal direction (“squeezed

images”) are expanded in the horizontal direction and

displayed on the entire screen with correct linearity.

(Normal images are expanded in the horizontal direction.)

WIDE size screen

The picture is expanded in the horizontal and vertical

directions at different ratios.

* Use this for watching normal video programs (4:3) with a

wide screen.

ZOOM size screen

The picture is expanded in the horizontal and vertical

direction, maintaining the original proportions.

* Use this for theater size (wide) movies, etc.

2.35:1 size screen

The squeezed film image is expanded to fulfill the entire

screen at a ratio of 2.35:1. Black bands do not appear at

the top and bottom but information is lost on the left and

right margins.

• This feature is available when the input signal is video,

component (480I, 480P, 576I, 576P, 720P, 1080I) or RGB

(525P or 625P signal from a scan converter).

* If black bands appear on the top and bottom in the full size

screen, select the 2.35:1 size screen to avoid phosphor burn-

in.

14:9 size screen

The image is displayed at a 14:9 aspect ratio.

* This feature is available when the input signal is video,

component (480I, 480P, 576I, 576P) or RGB (525P or 625P

signal from a scan converter).

Note:

Do not allow the displayed in 4:3 mode or 14:9 mode for

an extended period. This can cause a phosphor burn-in.

Information is lost on both sides.

Original image



WIDE Operations

English

WIDE Operations

10

En

Information

 Supported resolution

See page 29 for details on the display output of the

various VESA signal standards supported by the

monitor.

 When 852 (848) dot  480 line wide VGA*

signals with a vertical frequency of 60 Hz and

horizontal frequency of 31.7 (31.0) kHz are in-

put

Select an appropriate setting for RGB SELECT mode

referring to the“Table of Signals Supported” on page

29.

* “VGA”, “SVGA” and “SXGA” are registered

trademarks of IBM, Inc. of the United States.

Note:

Do not allow the displayed in 4:3 mode or 14:9 mode for

an extended period. This can cause a phosphor burn-in.

SCREEN SIZE Operation with

Computer Signals

Switch to the wide screen mode to expand the 4 : 3 image

to fill the entire screen.

1. Press the SCREEN SIZE button on the remote control.

2. Within 3 seconds ...

Press the SCREEN SIZE button again.

The screen size switches as follows:

→ 4:3 → FULL → ZOOM

4:3 size screen (4:3 or SXGA 5:4)

The picture has the same size as the normal computer image.

FULL size screen

The image is expanded in the horizontal direction.

ZOOM size screen

When wide signals are input.

FULL size screen

English

OSD (On Screen Display) Controls

11

En

Menu Operations

The OSD window is displayed with respect to the

screen as shown on the diagram.

* Depending on the screen’s mode, the OSD may be

displayed differently.

In the explanation, the OSD section is shown close up.

MAIN MENU

1 / 2

EXIT

PICTURE

SOUND

SCREEN

OPTION1

ADVANCED OSD

SEL. EXITOK

MENU

The following describes how to use the menus and the

selected items.

1. Press the MENU/SET button on the remote control to

display the MAIN MENU.

MAIN MENU

1 / 2

EXIT

PICTURE

SOUND

SCREEN

OPTION1

ADVANCED OSD

SEL. EXIT

OK

MENU

MAIN MENU

2 / 2

COLOR SYSTEM

SOURCE INFORMATION

SEL.

EXIT EXIT

OK

MENU

2. Press the cursor buttons ▲ ▼ on the remote control to

highlight the menu you wish to enter.

3. Press the MENU/SET button on the remote control to

select a sub menu or item.

PICTURE

1 / 2

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

TINT

AV SELECTION

DNR

: OFF

SEL.

ADJ.

EXIT RETURN

4. Adjust the level or change the setting of the selected item

by using the cursor buttons





on the remote control.

5. The adjustments or the settings that are stored in memory.

The change is stored until you change it again.

6. Repeat steps 2 – 5 to adjust an additional item, or press

the EXIT button on the remote control to return to the

main menu.

* When adjusting using the bar at the bottom of the screen,

press the



or



button within 5 seconds. If not, the

current setting is set and the previous screen appears.

Note:

The main menu disappears by pressing the EXIT

button.

Information

 Advanced menu mode

When “ADVANCED OSD” is set to “ON” in the main

menu (1/2), full menu items will be shown.

MAIN MENU

1 / 2

PICTURE

SOUND

SCREEN

OPTION1

OPTION2

OPTION3

ADVANCED OSD

SEL.

EXIT EXIT

OK

MENU

OSD (On Screen Display) Controls

Setting the language for the menus

The menu display can be set to one of seven languages.

Example: Setting the menu display to “DEUTSCH”

On “MAIN MENU”, select “LANGUAGE”, then press the

MENU/SET button.

The “LANGUAGE” screen appears.

On “LANGUAGE”, select “ DEUTSCH”, then press the

MENU/SET button.

LANGUAGE

:

DEUTSCH

EXIT RETURNOK

MENU

ADJ.

The “LANGUAGE” is set to “DEUTSCH” and return to the

main menu.

Information

 Language settings

ENGLISH ........ English

DEUTSCH.......German

FRANÇAIS ...... French

ESPAÑOL ....... Spanish

ITALIANO ........ Italian

SVENSKA ....... Swedish

У ............ Russian

English

OSD (On Screen Display) Controls

12

En

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET

REFERENCE

PICTURE CONTRAST ←→ 0←52→72 YES 14

BRIGHTNESS ←→ 0←32→64 YES 14

SHARPNESS ←→ 0←16→32 YES 14

COLOR ←→ 0←32→64 YES 14

TINT R←→G 0←32→64 YES 14

AV SELECTION DYNAMIC/STD/MOVIE1/MOVIE2/DEFAULT YES 14

DNR OFF/LOW/MID/HIGH YES 14

COLOR TEMP. LOW/MID LOW/MID/HIGH YES 14

WHITE BALANCE R.HIGH ←→ 0←40→70 YES 15

G.HIGH ←→ 0←40→70 YES 15

B.HIGH ←→ 0←40→70 YES 15

R.LOW ←→ 0←40→70 YES 15

G.LOW ←→ 0←40→70 YES 15

B.LOW ←→ 0←40→70 YES 15

RESET OFF←→ON YES 15

GAMMA 1←→2←

…

→4 YES 15

LOW TONE AUTO←→1←

…

→3 YES 15

C. DETAIL ADJ RED Y←→M0←32→64 YES 15

GREEN C←→Y0←32→64 YES 15

BLUE M←→C0←32→64 YES 15

YELLOW G←→R0←32→64 YES 15

MAGENTA R←→B0←32→64 YES 15

CYAN B←→G0←32→64 YES 15

RESET OFF←→ON YES 15

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET

REFERENCE

SOUND BASS ←→ 0←13→26 YES 16

TREBLE ←→ 0←13→26 YES 16

BALANCE L←→R -22←0→+22 YES 16

AUDIO INPUT1 VIDEO 1-3 / COMPNT 1-2 / PC1DSUB / PC2-BNC / PC3-DVI YES 16

AUDIO INPUT2 VIDEO 1-3 / COMPNT 1-2 / PC1DSUB / PC2-BNC / PC3-DVI YES 16

AUDIO INPUT3 VIDEO 1-3 / COMPNT 1-2 / PC1DSUB / PC2-BNC / PC3-DVI YES 16

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET

REFERENCE

SCREEN SCREEN SIZE 4:3/FULL/WIDE/ZOOM/2.35:1/14:9 — 16

V.POSITION ←→ -64←0→+64 YES 16

H.POSITION ←→ -128←0→+127 YES 16

V.SIZE ←→ 0←→64 YES 16

H.SIZE ←→ 0←→64 YES 16

AUTO PICTURE OFF←→ON*

2

NO 16

PHASE*

1

←→*

2

0←→64 YES 16

CLOCK*

1

←→*

2

0←64→128 YES 16

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET

REFERENCE

OPTION1 OSD DISPLAY OSD OFF←→ON YES 17

OSD ADJUST 1←

…

→6 YES 17

OSD ANGLE H←→V YES 17

OSD ORBITER OFF←→ON YES 17

OSD CONTRAST LOW←→NORMAL YES 17

BNC INPUT RGB←→COMP.←→SCART1←→SCART2 YES 17

D-SUB INPUT RGB←→SCART3 — 17

RGB SELECT AUTO/STILL/MOTION/WIDE1/WIDE2/WIDE3/WIDE4/DTV YES 18

HD SELECT 1080B/1035I/1080A NO 18

INPUT SKIP OFF←→ON YES 18

ALL RESET OFF←→ON —18

:Shaded areas indicate the default value.

←→

: Press the



or



button to adjust.

:Menu items in a ruled box are available when the ADVANCED OSD is set to ON.

Menu Tree

English

OSD (On Screen Display) Controls

13

En

*1 Only when AUTO PICTURE is OFF

*2 RGB/PC only

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET

REFERENCE

OPTION2 PWR. MGT. OFF←→ON YES 19

PURECINEMA OFF←→ON YES 19

LONG LIFE ABL AUTO/LOCK 1/LOCK 2/LOCK 3 YES 19

ORBITER AUTO 1 YES 20

AUTO 2 YES 20

MANUAL H-DOT/V-LINE/TIME YES 20

OFF YES 20

INVERSE OFF YES 20

ON WORKING TIME/WAITING TIME YES 20

WHITE YES 20

SCREEN WIPER OFF YES 21

ON WORKING TIME/WAITING TIME/SPEED YES 21

SOFT FOCUS OFF/1/2/3/4 YES 21

SIDE MASK 0←

…

→3←

…

→15 YES 21

S1/S2 AUTO←→OFF YES 22

DVI SET-UP PLUG/PLAY PC←→STB/DVD NO 22

BLACK LEVEL LOW←→HIGH NO 22

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET

REFERENCE

OPTION3 TIMER PRESENT TIME

DAYLIGHT SAIVING TIME

OFF←→ON NO 22

DAY/HOUR/MINUTES NO 22

PROGRAM OFF YES 23

ON DATE/ON/OFF(HOUR, MINUTE)/INPUT/FUNCTION YES 23

PWR. ON MODE LAST / VIDEO 1-3 / COMPNT 1-2 / PC1DSUB / PC2-BNC / PC3-DVI YES 23

KEY LOCK OFF←→ON YES 23

IR REMOTE OFF←→ON YES 24

LOOP OUT OFF←→ON YES 24

ID NUMBER ALL←→1←

…

→256 YES 24

VIDEO WALL DIVIDER OFF/1/4/9/16/25 YES 24

POSITION

No.1←

…

→No.4/No.7←

…

→No.15/No.16←

…

→No.31/No.32←

…

→No.56

— 25

DISP. MODE NORMAL←→ADJUST YES 25

AUTO ID OFF←→ON YES 25

SCREEN SCREEN SIZE 4:3/FULL/WIDE/ZOOM/2.35:1/14:9 — 26

V.POSITION ←→ -64←0→+64 YES 26

H.POSITION ←→ -128←0→+127 YES 26

V.SIZE ←→ 0←→64 YES 26

H.SIZE ←→ 0←→64 YES 26

AUTO PICTURE OFF←→ON*

2

NO 26

PHASE*

1

←→*

2

0←→64 YES 26

CLOCK*

1

←→*

2

0←64→128 YES 26

P. ON DELAY OFF/ON/MODE1/MODE2 YES 26

ABL LINK OFF←→ON YES 26

REPEAT TIMER OFF YES 27

ON DIVIDER/SOURCE/WORK TIME YES 27

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET

REFERENCE

ADVANCED OSD OFF←→ON YES 27

LANGUAGE ENGLISH/DEUTSCH/FRANÇAIS/ESPAÑOL/ITALIANO/SVENSKA/У NO 11

COLOR SYSTEM AUTO/3.58NTSC/4.43 NTSC/PAL/PAL 60/PAL-N/PAL-M/SECAM NO 27

SOURCE INFORMATION

— — 27

Information

 Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note that this also restores other settings to the factory defaults.

English

OSD (On Screen Display) Controls

14

En

Picture Settings Menu

Adjusting the picture

The contrast, brightness, sharpness, color and tint can be

adjusted as desired.

Example: Adjusting the contrast

On “CONTRAST” of “PICTURE” menu, adjust the contrast.

PICTURE

1 / 2

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

TINT

AV SELECTION

DNR

: OFF

SEL.

ADJ.

EXIT RETURN

CONTRAST

52

Note:

If “CAN NOT ADJUST” appears ...

When trying to enter the PICTURE submenu, make sure

AV SELECTION is not set to DEFAULT.

Information

 Picture adjustment screen

CONTRAST: Changes the picture’s white level.

BRIGHTNESS:

Changes the picture’s black level.

SHARPNESS: Changes the picture’s sharpness.

Adjusts picture detail of VIDEO display.

COLOR: Changes the color density.

TINT: Changes the picture’s tint. Adjust for natural

colored skin, background, etc.

 Adjusting the computer image

Only the contrast and brightness can be adjusted when

a computer signal is connected.

 Restoring the factory default settings

Select “DEFAULT” under the “AV SELECTION”

settings.

Setting the picture modes according to the

brightness of the room

There are four picture modes that can be used effectively

according to the environment in which you are viewing

the display.

Example: Setting the “MOVIE 1” mode

On “AV SELECTION” of “PICTURE” menu, select

“MOVIE 1”.

PICTURE

1 / 2

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

TINT

AV SELECTION

DNR

: OFF

SEL.

ADJ.

EXIT RETURN

AV SELECTION

: MOVIE 1

Information

 Types of AV SELECTIONS

MOVIE 1, 2: Set this mode when watching video in a

dark room.

This mode provides darker, finer pictures, like the

screen in movie theaters.

For a darker image, select MOVIE 2.

STD: Set this mode when watching video in a bright room.

This mode provides pictures with distinct differences

between light and dark sections.

DYNAMIC: This mode provides brighter pictures than

STD.

DEFAULT: Use this to reset the picture to the factory

default settings.

Reducing noise in the picture

Use these settings if the picture has noise due to poor

reception or when playing video tapes on which the picture

quality is poor.

Example: Setting “HIGH”

On “DNR” of “PICTURE” menu, select “HIGH”.

PICTURE

1 / 2

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

TINT

AV SELECTION

DNR

:

OFF

SEL.

ADJ.

EXIT RETURN

DNR

: HIGH

Information

 DNR

* “DNR” stands for Digital Noise Reduction.

* This function reduces noise in the picture.

 Types of noise reduction

There are three types of noise reduction. Each has a

different level of noise reduction.

The effect increases stronger in the order of LOW, MID

and High.

OFF: Turns the noise reduction function off.

Setting the color temperature

Use this procedure to set color tone produced by the plasma

display.

Example: Setting “HIGH”

On “COLOR TEMP.” of “PICTURE” menu, select “HIGH”.

PICTURE

2 / 2

GAMMA

LOW TONE

C.DETAIL ADJ.

: HIGH

: 2

: AUTO

SEL.

ADJ.

EXIT RETURN

Information

 Setting the color temperature

LOW: Redder

MID LOW: Slightly red

MID: Standard (slightly bluer)

HIGH: Bluer

English

OSD (On Screen Display) Controls

15

En

Adjusting the color to the desired level

Use this procedure to adjust the white balance for each

color temperature to achieve the desired color quality.

Example: Adjusting the “R.HIGH” of “HIGH” color

temperature

Set “ADVANCED OSD” to “ON” in the main menu (1/

2), then perform the following operations.

On “COLOR TEMP.” of “PICTURE” menu, select “HIGH”,

then press the MENU/SET button.

The “WHITE BALANCE” screen appears.

On “R.HIGH”, adjust the white balance.

WHITE BALANCE

COLOR TEMP. HIGH

R.HIGH

G.HIGH

B.HIGH

R.LOW

G.LOW

B.LOW

RESET : OFF

SEL.

ADJ.

EXIT RETURN

R.HIGH

70

Information

 Adjusting the white balance

R/G/B.HIGH: White balance adjustment for white level

R/G/B.LOW: White balance adjustment for black level

RESET: Resets settings to the factory default values.

Use



and



buttons to select “ON”, then press the

MENU/SET button.

 Restoring the factory default settings

Select “RESET” under the WHITE BALANCE menu.

Changing the Gamma Curve

This feature adjusts the brightness of the midtone areas

while keeping shadows and highlights unchanged.

Example: Setting “3”

Set “ADVANCED OSD” to “ON” in the MAIN MENU

(1/2), then perform the following operations.

On “GAMMA” of “PICTURE” menu, select “3”.

PICTURE

2 / 2

GAMMA

LOW TONE

C.DETAIL ADJ.

: MID

: 3

: AUTO

SEL.

ADJ.

EXIT RETURN

Information

 GAMMA settings

The picture becomes darker as the number increases

(in the sequence of 1, 2, 3, 4).

Making the Low Tone adjustments

This feature allows more detailed tone to be reproduced

especially in the dark area.

Example: Setting “2”

Set “ADVANCED OSD” to “ON” in the MAIN MENU

(1/2), then perform the following operations.

On “LOW TONE” of “PICTURE” menu, select “2”.

PICTURE

2 / 2

GAMMA

LOW TONE

C.DETAIL ADJ.

: MID

: 2

SEL.

ADJ.

EXIT RETURN

Information

 LOW TONE settings

AUTO: Will automatically appraise the picture and

make adjustments.

1: Will apply the dither method suitable for still pictures.

2: Will apply the dither method suitable for motion

pictures.

3: Will apply the error diffusion method.

Adjusting the colors

Use this procedure to adjust hue and color density for red,

green, blue, yellow, magenta and cyan.

You can accentuate the green color of trees, the blue of

the sky, etc.

Example: Adjusting the color detail adj for blue

Set “ADVANCED OSD” to “ON” in the MAIN MENU

(1/2), then perform the following operations.

On “PICTURE” menu, select “C. DETAIL ADJ”, then press

the MENU/SET button.

The “C. DETAIL ADJ” screen appears.

On “BLUE” of “C. DETAIL ADJ”, adjust the color detail.

C.DETAIL ADJ.

RED

GREEN

BLUE

YELLOW

MAGENTA

CYAN

RESET : OFF

SEL.

ADJ.

EXIT RETURN

M

G

R

B

C

Y

C

R

B

G

Y

M

Information

 C. DETAIL ADJ settings

RED: Makes red’s adjustment

GREEN: Makes green’s adjustment

BLUE: Makes blue’s adjustment

YELLOW: Makes yellow’s adjustment

MAGENTA: Makes magenta’s adjustment

CYAN: Makes cyan’s adjustment

RESET: Resets settings to the factory default value.

Use



and



buttons to select “ON”, then press the

MENU/SET button.

La page est en cours de chargement...

Pioneer Flat Panel Television PDP-42MVE1 Manuel utilisateur

Ce manuel convient également à

Pioneer Flat Panel Television PDP-42MVE1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents