Titan Tool 0290004 Le manuel du propriétaire

PowrLiner

550

0818 • Form No. 0293779C

AIRLESS, HIGH-PRESSURE

SPRAYING UNIT

AIRLESS HOCHDRUCK-

SPRITZGERÄT

GROUPE DE PROJECTION À

HAUTE PRESSION

- GB - OPERATING MANUAL 2

- D - BETRIEBSANLEITUNG 22

- F - MODE D’EMPLOI 44

OPERATING MANUAL

Models:

0290004

For use with latex or water-based

materials only.

Nur mit Latex oder wasser-

verdünnbaren Materialien verwenden.

Réservé à l’utilisation avec les produits

à base de latex ou d’eau.

2 PowrLiner 550

GB

Warning!

Attention: Danger of injury by injection!

Airless units develop extremely high spraying pressures.

Be safety conscious!

1

2

3

Never put your ngers, hands or any other parts of the body into

the spray jet!

Never point the spray gun at yourself, other persons or animals.

Never use the spray gun without safety guard.

Do not treat a spraying injury as a harmless cut. In case of injury

to the skin through coating materials or solvents, consult a doctor

immediately for quick and expert treatment. Inform the doctor

about the coating material or solvent used.

The operating instructions state that the following points must

always be observed before starting up:

1. Faulty units must not be used.

2. Secure Titan spray gun using the safety catch on the trigger.

3. Ensure that the unit is properly earthed.

4. Check allowable operating pressure of high-pressure hose and

spray gun.

5. Check all connections for leaks.

The instructions regarding regular cleaning and maintenance of

the unit must be strictly observed.

Before any work is done on the unit or for every break in work the

following rules must be observed:

1. Release the pressure from spray gun and hose.

2. Secure the Titan spray gun using the safety catch on the trigger.

3. Switch o unit.

Original Operating Manual

PowrLiner 550 1

GB

Contents

Page

1. Safety regulations for Airless spraying ..........................2

1.1 Explanation of symbols used ...................................................2

1.2 Gasoline engine safety ...............................................................5

1.3 Fueling (gas engine) ...................................................................6

2. General view of application .................................................7

2.1 Application ..................................................................................... 7

2.2 Coating materials .........................................................................7

3. Description of unit ....................................................................7

3.1 Airless process...............................................................................7

3.2 Functioning of the unit .............................................................. 7

3.3 System diagram............................................................................8

3.4 Technical data ...............................................................................9

3.5 Operator controls ........................................................................9

4. Operation ................................................................................... 10

4.1 Setup ............................................................................................. 10

4.2 Preparing to paint .................................................................... 11

4.3 Painting ........................................................................................ 12

4.4 Attaching the tip guard and tip ........................................... 13

4.5 Pressure relief procedure ....................................................... 13

4.6 Cleaning a clogged tip ............................................................ 14

4.7 Changing a spray tip ................................................................ 14

4.8 Stenciling ..................................................................................... 15

4.9 Operating the front caster ..................................................... 15

Page

5. Cleanup ....................................................................................... 15

5.1 Special cleanup instructions for use with

ammable solvents .................................................................. 15

5.2 Cleaning the sprayer................................................................ 15

5.3 Special cleanup.......................................................................... 16

5.4 Cleaning / replacing the gun lter ..................................... 16

5.5 Cleaning the Sureo™ valve .................................................. 17

6. Maintenance ............................................................................. 17

6.1 Adjusting the trigger tension ............................................... 17

6.2 Maintaining the engine .......................................................... 18

6.3 Safety shut-o switch .............................................................. 18

6.4 High pressure hose .................................................................. 18

6.5 Replacing the relief valve ....................................................... 19

6.6 Servicing the uid section ..................................................... 20

7. Remedy in case of faults ..................................................... 21

Accessories and spare parts .......................................................... 66

Spare parts list for the main assembly .....................................66/67

Spare parts list for the drive assembly .....................................68/69

Spare parts list for the cart assembly ......................................70/71

Spare parts list for gun holder assembly ................................72/73

Spare parts list for the spray gun ..................................................... 74

Connection diagram .......................................................................... 75

Accessories for PowrLiner 550 units.......................................... 76

Tip Chart ................................................................................................... 76

Warranty ................................................................................................ 80

2 PowrLiner 550

GB

Safety precautions

1. Safety regulations for Airless

spraying

1.1 Explanation of symbols used

This manual contains information that must

be read and understood before using the

equipment. When you come to an area that has

one of the following symbols, pay particular

attention and make certain to heed the

safeguard.

This symbol indicates a potential

hazard that may cause serious

injury or loss of life. Important

safety information will follow.

At

tention

This symbol indicates a potential

hazard to you or to the equipment.

Important information that tells

how to prevent damage to the

equipment or how to avoid causes

of minor injuries will follow.

Danger of skin injection

Danger of re from solvent and

paint fumes

Danger of explosion from solvent,

paint fumes and incompatible

materials

Danger of injury from inhalation

of harmful vapors

i

Notes give important information

which should be given special

attention.

HAZARD: INJECTION INJURY

A high pressure stream produced

by this equipment can pierce the

skin and underlying tissues, leading

to serious injury and possible

amputation.

Do not treat a spraying injury as

a harmless cut. In case of injury to

the skin through coating materials

or solvents, consult a doctor

immediately for quick and expert

treatment. Inform the doctor about

the coating material or solvent used.

PREVENTION:

• NEVER aim the gun at any part of the body.

• NEVER allow any part of the body to touch

the uid stream. DO NOT allow body to

touch a leak in the uid hose.

• NEVER put your hand in front of the gun.

Gloves will not provide protection against

an injection injury.

• ALWAYS lock the gun trigger, shut the uid

pump o and release all pressure before

servicing, cleaning the tip guard, changing

tips, or leaving unattended. Pressure will

not be released by turning o the engine.

The PRIME/SPRAY valve or pressure bleed

valve must be turned to their appropriate

positions to relieve system pressure.

• ALWAYS keep tip guard in place while

spraying. The tip guard provides some

protection but is mainly a warning device.

• ALWAYS remove the spray tip before

ushing or cleaning the system.

• NEVER use a spray gun without a working

trigger lock and trigger guard in place.

• All accessories must be rated at or above

the maximum operating pressure range of

the sprayer. This includes spray tips, guns,

extensions, and hose.

PowrLiner 550 3

GB

Safety precautions

HAZARD

: HIGH PRESSURE HOSE

The paint hose can develop leaks

from wear, kinking and abuse. A

leak can inject material into the skin.

Inspect the hose before each use.

PREVENTION:

• Avoid sharp bending or kinking of the

high-pressure hose. The smallest bending

radius amounts to about 20 cm.

• Do not drive over the high-pressure hose.

Protect against sharp objects and edges.

• Replace any damaged high-pressure hose

immediately.

• Never repair defective high-pressure hoses

yourself!

• Electrostatic charging of spray guns and

the high-pressure hose is discharged

through the high-pressure hose. For this

reason the electric resistance between the

connections of the high-pressure hose

must be equal to or lower than 1MΩ.

• For reasons of function, safety and

durability use only original Titan high-

pressure hoses.

• Before each use, check all hoses for cuts,

leaks, abrasion or bulging of cover. Check

for damage or movement of couplings.

Immediately replace the hose if any of

these conditions exist. Never repair a paint

hose. Replace it with another earthed high-

pressure hose.

• Make sure power cord, air hose and spray

hoses are routed in such a manner to

minimize slip, trip and fall hazard.

HAZARD: EXPLOSION OR FIRE

Flammable vapors, such as solvent

and paint vapors, in work area can

ignite or explode.

PREVENTION:

• Use equipment only in well ventilated area.

Keep a good supply of fresh air moving

through the area to keep the air within

the spray area free from accumulation of

ammable vapors. Keep pump assembly

in well ventilated area. Do not spray pump

assembly.

• Gas models only - Do not ll fuel tank while

engine is running or hot; shut o engine

and allow to cool. Fuel is ammable and

can ignite or explode if spilled on a hot

surface.

• Eliminate all ignition sources, such as pilot

lights, cigarettes, portable electric lamps

and plastic drop cloths (potential static

arc).

• Keep work area free of debris, including

solvent, rags and gasoline.

• Do not plug or unplug power cords, or turn

power or light switches on or o when

ammable vapors are present.

• Ground equipment and conductive objects

in work area. Make sure grounding chain is

in place and reaches the ground.

• Use only grounded hoses.

• Hold spray gun rmly to the side of a

grounded pail when triggering into pail.

• If there is static sparking or if you feel a

shock, stop operation immediately.

• Know the contents of the paint and

solvents being sprayed. Read all Material

Safety Data Sheets (MSDS) and container

labels provided with the paints and

solvents. Follow the paint and solvent

manufacturer’s safety instructions.

• Do not use a paint or solvent containing

halogenated hydrocarbons. Such as

chlorine, bleach, mildewcide, methylene

chloride and trichloroethane. They are not

compatible with aluminum. Contact the

coating supplier about compatibility of

material with aluminum.

• Keep a re extinguisher in work area.

4 PowrLiner 550

GB

Safety precautions

HAZARD: HAZARDOUS VAPORS

Paints, solvents, and other materials

can be harmful if inhaled or come

in contact with body. Vapors can

cause severe nausea, fainting, or

poisoning.

PREVENTION:

• Wear respiratory protection when

spraying. Read all instructions supplied

with the mask to be sure it will provide the

necessary protection.

• All local regulations regarding protection

against hazardous vapors must be

observed.

• Wear protective eyewear.

• Protective clothing, gloves and possibly

skin protection cream are necessary

for the protection of the skin. Observe

the regulations of the manufacturer

concerning coating materials, solvents and

cleaning agents in preparation, processing

and cleaning units.

HAZARD: GENERAL

This product can cause severe injury

or property damage.

PREVENTION:

• Follow all appropriate local, state, and

national codes governing ventilation, re

prevention, and operation.

• Pulling the trigger causes a recoil force

to the hand that is holding the spray

gun. The recoil force of the spray gun

is particularly powerful when the tip

has been removed and a high pressure

has been set on the airless pump. When

cleaning without a spray tip, set the

pressure control knob to the lowest

pressure.

• Use only manufacturer authorized parts.

User assumes all risks and liabilities when

using parts that do not meet the minimum

specications and safety devices of the

pump manufacturer.

• ALWAYS follow the material

manufacturer’s instructions for safe

handling of paint and solvents.

• Clean up all material and solvent spills

immediately to prevent slip hazard.

• Wear ear protection. This unit can produce

noise levels above 85 dB(A).

• Never leave this equipment unattended.

Keep away from children or anyone not

familiar with the operation of airless

equipment.

• Do not spray on windy days.

• The device and all related liquids (i.e.

hydraulic oil) must be disposed of in an

environmentally friendly way.

PowrLiner 550 5

GB

Safety precautions

1.2 Gasoline Engine Safety

1. Gas engines are designed to give safe and

dependable service if operated according

to instructions. Read and understand the

engine manufacturer’s Owner’s Manual

before operating the engine. Failure to

do so could result in personal injury or

equipment damage.

2. To prevent re hazards and to provide

adequate ventilation, keep the engine at

least 1 meter (3 feet) away from buildings

and other equipment during operation.

Do not place ammable objects close to

the engine.

3. People who are not operating the device

must stay away from the area of operation

due to a possibility of burns from hot

engine components or injury from any

equipment the engine may be used to

operate.

4. Know how to stop the engine quickly, and

understand the operation of all controls.

Never permit anyone to operate the

engine without proper instructions.

5. Gasoline is extremely ammable and is

explosive under certain conditions.

6. Refuel in a well-ventilated area with the

engine stopped. Do not smoke or allow

ames or sparks in the refueling area or

where gasoline is stored.

7. Do not overll the fuel tank. After

refueling, make sure the tank cap is closed

properly and securely.

8. Be careful not to spill fuel when refueling.

Fuel vapor or spilled fuel may ignite. If any

fuel is spilled, make sure the area is dry

before starting the engine.

9. Never run the engine in an enclosed or

conned area. Exhaust contains poisonous

carbon monoxide gas; exposure may cause

loss of consciousness and may lead to

death.

10. The muer becomes very hot during

operation and remains hot for a while after

stopping the engine. Be careful not to

touch the muer while it is hot. To avoid

severe burns or re hazards, let the engine

cool before transporting it or storing it

indoors.

11. Never ship/transport sprayer with gasoline

in the tank.

DO NOT use this equipment to spray

water or acid.

Attention

Do not lift by cart handle when

loading or unloading.

Device is very heavy. Three-person

lift is required.

6 PowrLiner 550

GB

Safety precautions

1.3 Fueling (gas engine)

Gasoline is extremely ammable

and is explosive under certain

conditions.

Fuel Specications

• Use automotive gasoline that has a pump

octane number of 86 or higher, or that has

a research octane number of 91 or higher.

Use of a lower octane gasoline can cause

persistent “pinging” or heavy “spark knock”

(a metallic rapping noise) which, if severe,

can lead to engine damage.

i

If “spark knock” or “pinging” occurs

at a steady engine speed under

normal load, change brands of

gasoline. If spark knock or pinging

persists, consult an authorized

dealer of the engine manufacturer.

Failure to do so is considered

misuse, and damage caused by

misuse is not covered by the engine

manufacturer’s limited warranty.

Occasionally you may experience

light spark knock while operating

under heavy loads. This is no cause

for concern, it simply means your

engine is operating eciently.

• Unleaded fuel produces fewer engine and

spark plug deposits and extends the life of

the exhaust system components.

• Never use stale or contaminated gasoline

or an oil/gasoline mixture. Avoid getting

dirt, dust, or water in the fuel tank.

Gasolines Containing Alcohol

If you decide to use a gasoline containing

alcohol (gasohol), be sure its octane rating is

at least as high as that recommended by the

engine manufacturer. There are two types of

“gasohol”: one containing ethanol, and the

other containing methanol. Do not use gasohol

that contains more than 10% ethanol. Do not

use gasoline containing methanol (methyl or

wood alcohol) that does not also contain co-

solvents and corrosion inhibitors for methanol.

Never use gasoline containing more than

5% methanol, even if it has co-solvents and

corrosion inhibitors.

i

Fuel system damage or engine

performance problems resulting

from the use of fuels that contain

alcohol is not covered under the

warranty. The engine manufacturer

cannot endorse the use of fuels

containing methanol since evidence

of their suitability is incomplete at

this time.

Before buying gasoline from an

unfamiliar station, try to nd out

if the gasoline contains alcohol.

If it does, conrm the type and

percentage of alcohol used. If you

notice any undesirable operating

characteristics while using a

gasoline that contains alcohol, or

one that you think contains alcohol,

switch to a gasoline that you know

does not contain alcohol.

PowrLiner 550 7

GB

General view of application Description of unit

2. General view of application

2.1 Application

This airless line striper is a precision power tool used to

spray many types of material for many types of applications

including parking lots, curbs, and athletic elds. Read and

follow this instruction manual carefully for proper operating

instructions, maintenance, and safety information.

2.2 Coating materials

Processible coating materials

i

Pay attention to the Airless quality of the

coating materials to be processed.

Latex paint, dispersion paints, re protection and thick lm

materials, zinc dust and micaceous iron ore paints, Airless

spray primer, sprayable glue, anti-corrosive agents, thick

coating materials and bitumen-like coating materials.

No other materials should be used for spraying without Titan’s

approval.

Filtering

In spite of the high-pressure lter, ltering of the coating

material is recommended in general.

Mix coating material before commencement of work.

i

Make sure when stirring with motor-driven

agitators that no air bubbles are stirred in. Air

bubbles disturb when spraying and can, in fact,

lead to interruption of operation.

Viscosity

It is possible to work with high-viscosity coating materials with

the devices.

If highly viscous coating materials cannot be sucked up,

they must be diluted in accordance with the manufacturer’s

instruction.

Two-component coating material

The appropriate processing time must be adhered to exactly.

A minimum of 45 minute set time is recommended. Within

this time rinse through and clean the unit meticulously with

the appropriate cleaning agents.

Coating materials with sharp-edged additional materials

These have a strong wear and tear eect on valves, high-

pressure hose, spray gun and tip. The durability of these parts

can be reduced appreciably through this.

3. Description of unit

3.1 Airless process

The main area of application are thick layers of highly viscous

coating material for large areas and a high consumption of

material.

A piston pump takes in the coating material by suction and

conveys it to the tip. Pressed through the tip at a pressure of

up to a maximum of 172 bar (17.2 MPa), the coating material

is atomized. This high pressure has the eect of micro ne

atomisation of the coating material.

As no air is used in this process, it is described as an AIRLESS

process.

This method of spraying has the advantages of nest

atomisation, cloudless operation and a smooth, bubble-free

surface. As well as these, the advantages of the speed of work

and convenience must be mentioned.

3.2 Functioning of the unit

The following section contains a brief description of the

technical construction for better understanding of the

function.

Titan PowrLiner 550 (PL) are high-pressure spraying units

driven by a gasoline engine.

The gasoline engine (g. 1, item 1) drives the pump assembly

(2) which moves the piston up and down inside the uid

section (3).

The inlet valve is opened automatically by the upwards

movement of the piston. The outlet valve is opened when the

piston moves downward.

The coating material ows under high pressure through

the high-pressure hose to the spray gun. When the coating

material exits from the tip it atomizes.

3

2

1

8 PowrLiner 550

GB

Description of unit

3.3 System diagram

1 Spray lever

2 Handle adjustment knob

3 High-pressure hose outlet

4 Sureo™ valve

5 Gun riser

6 Gun support bar

7 High-pressure spray gun

8 Throttle / gun cable

9 Airless spray hose

10 Bleed hose

11 Suction tube

12 Gasoline engine

13 Engine shuto switch

14 Relief valve handle:

Turn left for circulation k

Turn right for spray p

1

3

2

14

13

12

10

8

9

11

7

4

5

6

SPRAY

PRIME

SPRAY

PRIME

k

p

=

PowrLiner 550 9

GB

Description of unit

PL550

Gasoline engine, power

37.7cc, 4-stroke gas engine

Fuel Capacity

0,65 L

Max. operating pressure

17,2 MPa (172 bar)

Max. sound pressure level

92 dB*

Max. size of tip with a spray gun

Trac marking 0,019” – 0,48 mm

Field marking 0,023” – 0,58 mm

Max. volume ow

1,25 l/min

Weight

29,5 kg

Max. viscosity

20.000 mPa·s

Dimensions L x W x H

104 cm x 53,3 cm x 81,3 cm

Altitude

This equipment will operate

correctly up to 2000 m above

mean sea level

Max. temperature of the coating material

43° C

Max. tire pressure

0,2 MPa (2 bar)

Special high-pressure hose

DN 6 mm, 15 m (50’ x 1/4”),

connection thread NPSM 1/4

* Place of measurement: 1 m distance from unit and 1.60

m above reverberant oor, 120 bar (12 MPa) operating

pressure.

Attention

Do not remove the spray gun from the gun

holder and attempt to use it independently.

Doing this will will engage the safety shut-off

switch.

3.4 Technical data

3.5 Operator controls

The following section describes the operator controls on the

spray gun and line striper.

Spray Gun Trigger Lock

Engage the trigger lock whenever the gun is not in use.

The gun is locked when the trigger lock is at a 90º angle

(perpendicular to the trigger in either direction).

i

If necessary, loosen the gun holder clamp knob

and then engage the spray gun trigger lock.

Move the spray gun to its original position and

tighten the clamp knob.

Spray Lever

The spray lever is a dual-function lever. It is located on the cart

handle (g. 4, item 1).

1

The spray lever controls the throttle on the engine as well as

the trigger on the spray gun.

Pulling the spray lever will simultaneously trigger the spray

gun as well as rev up the engine. This engages the engine

clutch with the pump and causes the sprayer to build

pressure.

i

The sprayer is equipped with an automatic

safety shut-o switch to prevent the sprayer

from over-pressurizing. When the relief valve is

in the SPRAY (p ) position , pulling and holding

the spray lever half way without triggering

the spray gun will engage the safety shut-o

switch. Refer to the Maintenance section if the

safety shut-o switch engages.

10 PowrLiner 550

GB

Description of unit Operation

4. Operation

This equipment produces a fluid stream at

extremely high pressure. Read and understand

the warnings in the Safety Precautions section

at the front of this manual before operating

this equipment.

4.1 Setup

1. Attach the handle to the cart (g. 7).

a. Line up the hole in the bottom of the handle with the

support weldment on the cart.

b. Thread the bolt through the hole in the handle and

the weldment. Tighten by turning the knob of the bolt

clockwise (1).

c. Position the handle at the desired height. Loosen the

knob on the rear of the support weldment (2) in order to to

loosen the handle.

d. Pull the handle up or down to the desired height. Tighten

the handle knob in order to secure the handle.

2

1

i

The spray gun and cables are mounted to the

gun support bar at the factory.

Do not attach the tip to the spray gun yet.

Remove the tip if it is already attached.

2. Make sure that the siphon tube and the bleed hose are

attached and secure.

3. Using a wrench, thread the airless spray hose to the

outlet tting on the sprayer. Tighten securely.

4. Attach an airless spray gun to the spray hose. Using

two wrenches (one on the gun and one on the hose),

tighten securely.

5. Position the spray gun (g 8).

a. Loosen the support bar knob (1) and slide the gun support

bar to the desired horizontal position. Make sure the gun is

far enough away from the cart so that the rear wheel does

not track over the fresh spray pattern.

b. Loosen the gun riser clamp (2) and slide the spray gun to

the desired vertical position. A distance of 6” from the tip to

the spray surface is a good starting point.

Relief Valve

The relief valve (g. 5, item 1) directs material to the material

bleed hose when set to PRIME (k) or to high pressure spray

hose when set to SPRAY (p).

The arrows on the relief valve knob shows the rotation

directions for PRIME (k) and SPRAY (p).

Shuto Switch

The engine shuto switch (g. 5, item 2) will shut the engine

o when it is running.

Press and hold the shutu switch in order to shut the engine

o.

2

1

Sureo™ Valve

The Sureo™ Valve (g. 6, item 1) is designed to keep the inlet

valve open and from sticking to dried materials.

The Sureo Valve is activated manual by the user.

1

PowrLiner 550 11

GB

Operation

1

2

i

The height of the spray gun aects the width

of the spray pattern (i.e., the lower the gun, the

smaller the line width). Tip size also aects line

width.

6. Make sure the throttle cable and gun cable are

operating properly.

When pulling the spray lever on the cart handle, the

throttle cable should be fully moving the throttle lever

on the engine, and the gun cable should be pulling the

gun trigger at the same time.

These cables are factory-set to operate properly. If

adjustment to the gun trigger tension is required, refer

to the “Adjusting the Trigger Tension” procedure in the

Maintenance section of this manual.

7. Turn the relief valve knob to the PRIME (k) position.

Attention

Never operate unit for more than ten seconds

without fluid. Operating this unit without fluid

will cause unnecessary wear to the packings.

8. Squirt a teaspoon of Piston Lube™ (P/N 314-480, sold

separately) into the indicated area. Light household oil

can be substituted if necessary.

9. Check the engine oil level. The gasoline engine oil level

is determined by the manufacturer. Refer to the engine

manufacturer’s service manual (supplied).

10. Fill the gas tank on the engine with unleaded gasoline

only. Do not mix the gasoline with 2-cycle oil.

4.2 Preparing to paint

Before painting, it is important to make sure that the uid in

the system is compatible with the paint that is going to be

used.

i

If this unit is new, it is shipped with test uid in

the uid section to prevent corrosion during

shipment and storage. This uid must be

thoroughly cleaned out of the system with

mineral spirits before you begin spraying.

i

Incompatible uids and paint may cause the

valves to become stuck closed, which would

require disassembly and cleaning of the

sprayer’s uid section.

Attention

Always keep the trigger lock on the spray gun

in the locked position while preparing the

system. If necessary, loosen the gun holder

clamp knob and then engage the spray gun

trigger lock.

1. Place the siphon tube into a container of the

appropriate solvent for the material being sprayed

(refer to recommendations of the material

manufacturer). An example of the appropriate solvent

is water for latex paint.

2. Place the bleed hose into a metal waste container.

3. Turn the relief valve knob to the PRIME (

k) position.

4. Fully depress the pusher stem to make sure the inlet

ball is free.

5. Start the engine (g. 10):

a. Move the choke lever (1) up to the full choke position.

b. Push the rubber prime button (2) 7-10 times.

c. Pull the starter rope (3) rapidly and rmly. Continue to hold

the rope as you let it return. Pull and return the rope until

the engine starts.

d. Once the engine is running, slowly move the choke lever (1)

down to the closed position

2

3

1

6. Fluid will begin owing through the return hose and

into the waste container. Allow the sprayer to run for

15–30 seconds to ush the test uid out through the

return hose and into the waste container.

7. Turn o the sprayer by pressing and holding the engine

shuto switch until the motor shuts o.

i

Make sure that the spray gun does not have a

tip or tip guard installed.

8. Place a metal waste container underneath the spray

gun to catch the solvent.

9. Start the engine.

12 PowrLiner 550

GB

Operation

4.3 Painting

1. Place a ve gallon bucket of material between the

bucket holders on the cart. Make sure the bucket

holders hold the ve gallon bucket securely. Adjust

the bucket holders using the thumb screw located

underneath each holder, if necessary.

i

When using this line striper for rst time, it

may be helpful to use water in place of paint to

gain familiarity with the operation of the line

striper. After changing from water to paint,

test spray several lines on cardboard, roong

felt, or rosin paper before striping to ensure

correct line width.

2. Place the siphon hose into a container of paint.

3. Place the bleed hose into a metal waste container.

4. Turn the relief valve knob to the PRIME (

k) position.

5. Fully depress the pusher stem to make sure the inlet

ball is free.

6. Start the engine:

a. Move the choke lever (1) up to the full choke position.

b. Push the rubber prime button (2) 7-10 times.

c. Pull the starter rope (3) rapidly and rmly. Continue to hold

the rope as you let it return. Pull and return the rope until

the engine starts.

d. Once the engine is running, slowly move the choke lever (1)

down to the closed position

7. Fluid will begin owing through the return hose and

into the waste container. Allow the sprayer to run for

15–30 seconds to ush the test uid out through the

return hose and into the waste container.

8. Turn o the sprayer by pressing and holding the engine

shuto switch until the motor shuts o.

9. Remove the bleed hose from the waste container and

place it into the container of paint.

10. Start the engine.

11. Turn the relief valve knob to the SPRAY (p) position.

12. Unlock the gun by turning the gun trigger lock to the

unlocked position.

13. Fully pull the spray lever on the cart handle to rev the

engine, pressurize the sprayer, and trigger the spray

gun. Fluid will begin owing through the spray hose

and out of the gun.

14. Continue to pull the spray lever on the cart handle until

material is coming out of the gun.

15. Release the spray lever.

16. Lock the gun by turning the gun trigger lock to the

locked position. If necessary, loosen the gun holder

clamp knob and then engage the spray gun trigger lock.

Move the spray gun to its original position and tighten

the clamp knob.

17. Turn the relief valve knob to the PRIME (k) position.

18. Turn o the sprayer by pressing and holding the engine

shuto switch until the motor shuts o.

19. Attach tip guard and tip to the spray gun. Refer to the

instructions in section 4.4.

10. Turn the relief valve knob to the SPRAY (

p) position.

11. Unlock the gun by turning the gun trigger lock to the

unlocked position.

12. Fully pull the spray lever on the cart handle to rev the

engine, pressurize the sprayer, and trigger the spray

gun. Fluid will begin owing through the spray hose

and out of the gun.

13. Continue to pull the spray lever on the cart handle until

the old solvent/test uid is gone and fresh solvent is

coming out of the gun.

14. Release the spray lever.

15. Lock the gun by turning the gun trigger lock to the

locked position. If necessary, loosen the gun holder

clamp knob and then engage the spray gun trigger lock.

Move the spray gun to its original position and tighten

the clamp knob.

16. Check the entire system for leaks. If leaks occur,

turn the sprayer o and follow the “Pressure Relief

Procedure” in this manual before tightening any ttings

or hoses.

17. Follow the “Pressure Relief Procedure” (section 4.5) in

this manual before changing from solvent to paint.

Be sure to follow the Pressure Relief Procedure

when shutting the unit down for any purpose,

including servicing or adjusting any part of the

spray system, changing or cleaning spray tips,

or preparing for cleanup.

PowrLiner 550 13

GB

Operation

4.4 Attaching the tip guard and tip

Use the following procedure to install the tip guard and tip to

the spray gun.

1. Perform the “Pressure Relief Procedure” described in

this manual (section 4.5).

2. Using a pen or similar object, insert the tip seal (3) and

seal (4) into the back of the tip guard (2). Press in for

nal adjustment.

3. Insert the tip (1) into the slot on the tip guard.

1

2

3

4

4. Thread the tip guard onto the gun. Position the tip

guard in the desired spraying position, then tighten

securely.

i

The arrow on the tip handle should be pointing

in the forward direction for spraying.

4.5 Pressure Relief Procedure

Be sure to follow the Pressure Relief Procedure

when shutting the unit down for any purpose,

including servicing or adjusting any part of

the spray system, changing or cleaning spray

nozzles, or preparing for cleanup.

1. Lock the gun by turning the gun trigger lock to the

locked position. If necessary, loosen the gun holder

clamp knob and then engage the spray gun trigger lock.

Move the spray gun to its original position and tighten

the clamp knob.

2. Turn the relief valve knob to the PRIME (

k) position.

3. Turn o the sprayer by pressing and holding the engine

shuto switch until the motor shuts o.

4. Unlock the gun by turning the gun trigger lock to the

unlocked position.

5. Fully pull the spray lever on the cart handle to trigger

the spray gun and release any remaining pressure in the

hose.

6. Lock the gun by turning the gun trigger lock to the

locked position. If necessary, loosen the gun holder

clamp knob and then engage the spray gun trigger lock.

Move the spray gun to its original position and tighten

the clamp knob.

POSSIBLE INJECTION HAZARD. Do not spray

without the tip guard in place. Never trigger

the gun unless the tip is in either the spray or

the unclog position. Always engage the gun

trigger lock before removing, replacing or

cleaning tip.

20. Start the engine.

21. Turn the relief valve knob to the SPRAY (

p) position.

22. Fully pull the spray lever on the cart handle to rev the

engine, pressurize the sprayer, and trigger the spray

gun. Test the spray pattern and line position on a long

piece of roong felt or cardboard. Check for proper line

width and position. If adjustment to the position of the

spray gun is required, refer to the “Setup” procedure

earlier in this section.

23. Make sure that the spray gun shuts o completely when

the gun trigger is released. If adjustment to the trigger

tension is required, refer to the “Adjusting the Trigger

Tension” procedure in the Maintenance section of this

manual.

24. Begin striping.

a. Position the line striper slightly in front of the striping path.

b. Start walking with the line striper and trigger the gun at the

beginning of the striping path.

c. At the end of striping path, release the trigger and continue

walking a short distance, if possible.

i

Triggering the gun after the line striper is

moving and releasing the trigger before the

line striper stops produces an evenly painted

line from start to nish. If the striping path

ends at an obstacle, release the trigger at

the same moment that the line striper stops

moving.

4.6 Clearing a clogged tip

If the spray pattern becomes distorted or stops completely

while the trigger is pulled, follow these steps.

Attention

DO NOT continue to pull the spray lever if the

spray tip is clogged. Continued pull on the

lever with a clogged tip will over-pressurize the

unit, causing it to shut down.

Attention

Do not attempt to remove the spray gun from

the gun holder to clean the tip.

1. Place a sheet of cardboard or small bucket under the

spray gun to catch the paint.

2. Rotate the tip 180º so that the arrow on the tip handle is

pointing opposite the spray direction.

i

If the tip is dicult to rotate, relieve pressure

by 1) slowly turning the relief valve knob to

PRIME (k), 2) unlock the spray gun, and 3)

squeeze the spray lever. Release the lever, lock

the spray gun, and try rotating the spray tip

again.

3. Make sure the relief valve knob is turned to the SPRAY

(

p) position. Unlock the spray gun.

4. Trigger the gun once so that the pressure can blow the

clog out.

Attention

Never pull the trigger more than once at a time

with the tip in the reverse position.

5. Continue this procedure until the tip is clear of the clog.

Do not attempt to clean the tip with your

finger.

Attention

Do not use a needle or other sharp pointed

instrument to clean the tip. The hard tungsten

carbide is brittle and can be chipped.

4.7 Changing a spray tip

Tips can be removed and replaced easily without

disassembling the gun.

Never attempt to change or clean the tip or tip

guard without first performing the “Pressure

Relief Procedure.”

1. Perform the “Pressure Relief Procedure” described in the

sprayer’s Owner’s Manual.

2. Remove the tip (g. 14, item 1) from the slot on the tip

guard (2).

3. Insert the new tip into the slot on the tip guard. The

arrow on the tip handle should be pointing in the

forward direction for spraying.

Removing the seal and tip seal

1. Remove the tip from the tip guard.

2. Insert the tip handle through the front of the tip guard.

3. Push the seal (3) and tip seal (4) out through the back of

the tip guard.

1

2

4

3

Identifying Tip Sizes

To identify tip sizes, use the following formula. A “417” tip size

will be used in this example.

The rst digit represents the size of the spray pattern when

spraying 6” away from the work surface:

4 = 4” spray pattern

The second two digits represent the diameter of the orice on

the tip:

17 = .017” orice

i

Worn spray tips will adversely aect the spray

pattern and result in reduced production, poor

nish, and wasted material. Replace worn tips

immediately.

14 PowrLiner 550

GB

Operation

4.8 Stenciling

Attention

Do not remove the spray gun from the gun

holder and attempt to use it independently.

Doing this will will engage the safety shut-off

switch.

The spray gun cannot be removed from the gun holder to

perform stencil work. To stencil with this line striper, make

multiple spraying passes from right to left over the stencil.

4.9 Operating the Front Caster

The front caster on the cart is designed to track the sprayer

in either a straight line or allow a desired radius to be set. To

adjust the front caster:

1. Loosen the two caster bolts on the top side of the

caster.

2. Move the front wheel to the proper position for the

desired radius.

3. Re-tighten the bolts to secure the caster in position.

1

5. Cleanup

Attention

The sprayer, hose, and gun should be cleaned

thoroughly after daily use. Failure to do so

permits material to build up, seriously aecting

the performance of the unit.

Always spray at minimum pressure with the

gun nozzle tip removed when using mineral

spirits or any other solvent to clean the sprayer,

hose, or gun. Static electricity buildup may

result in a re or explosion in the presence of

ammable vapors.

5.1 Special cleanup instructions for use with

ammable solvents

• Always ush spray gun preferably outside and at least

one hose length from spray pump.

• If collecting ushed solvents in a one gallon metal

container, place it into an empty ve gallon container,

then ush solvents.

• Area must be free of ammable vapors.

• Follow all cleanup instructions.

PowrLiner 550 15

GB

Operation Cleanup

5.2 Cleaning the sprayer

1. Follow the “Pressure Relief Procedure” found in the

Operation section of this manual, section 4.5.

2. Remove the gun tip and tip guard and clean with a

brush using the appropriate solvent.

3. Place the siphon tube into a container of the

appropriate solvent (refer to recommendations of the

material manufacturer). An example of the appropriate

solvent is water for latex paint.

4. Place the return hose into a metal waste container.

5. Turn the relief valve knob to the PRIME (k) position.

6. Start the engine.

7. Fluid will begin owing through the return hose and

into the waste container. Allow the uid to circulate

through the sprayer and ush the paint out of the

return hose into the metal waste container.

8. Turn o the sprayer by pressing and holding the engine

shuto switch until the motor shuts o.

9. Place a metal waste container underneath the spray

gun to catch the paint and solvent.

10. Start the engine.

11. Turn the relief valve knob to the SPRAY (p) position.

12. Fully pull the spray lever on the cart handle to rev the

engine, pressurize the sprayer, and trigger the spray

gun. Fluid will begin owing through the spray hose

and out of the gun.

13. Continue to pull the spray lever on the cart handle until

the material is ushed out of the hose and the solvent

coming out of the gun is clean.

14. Release the spray lever.

i

For long-term or cold weather storage, pump

Pump Saver™ through the entire system.

15. Follow the “Pressure Relief Procedure” found in the

Operation section of this manual.

16. Store the sprayer in a clean, dry area.

Attention

Do not store the unit under pressure.

Attention

Do not put the high-pressure hose into

solvents. Use only a wet cloth to wipe down the

outside of the hose.

16 PowrLiner 550

GB

Cleanup

5.3 Special cleanup

Attention

Perform the following procedure after spraying

with water-based materials only.

Perform the following procedure when the valves of the

sprayer are stuck or when preparing the sprayer for long term

storage. The use of a pump cleaning adapter that attaches to

the bottom of the siphon tube is required (the pump cleaning

adapter is included with the sprayer).

1. Lock the gun and remove the spray tip assembly. If

necessary, loosen the gun holder clamp knob and then

engage the spray gun trigger lock. Move the spray gun

to its original position and tighten the clamp knob.

Place the suction tube and return hose into an empty

waste container.

2

4

3

1

2. Using a garden hose,

rinse o the siphon

tube (1), return

hose and inlet lter.

Empty the waste

container.

3. Remove the inlet

lter from the

suction tube and

place into a waste

container.

4. Verify that the seals

(2) are present inside

the adapter (3) and

siphon tube. Thread

the pump cleaning

adapter onto a

garden hose (4). Connect the hose and adapter to the

tting on the end of the siphon tube.

5. Unclip the return hose from the siphon tube and place

it into the waste container.

6. Turn the relief valve knob to the PRIME (k) position.

7. Turn on the water supply.

8. Start the engine. Water will go into the siphon tube and

out through the return hose. Let the sprayer run for a

few minutes to allow the return hose to be ushed.

9. Turn o the sprayer by pressing and holding the engine

shuto switch until the motor shuts o.

10. Place a metal waste container underneath the spray

gun to catch the cleaning solution.

11. Start the engine.

12. Turn the relief valve knob to the SPRAY (p) position.

13. Fully pull the spray lever on the cart handle to rev the

engine, pressurize the sprayer, and trigger the spray

gun. Fluid will begin owing through the spray hose

and out of the gun.

14. Continue to pull the spray lever on the cart handle until

the material is ushed out of the hose and the water

coming out of the gun is clean.

15. Release the spray lever.

16. Follow the “Pressure Relief Procedure” found in the

Operation section of this manual.

5.4 Cleaning / replacing the gun lter

The gun lter must be cleaned after every use of the sprayer.

When using thicker spray materials, the lter might need to be

cleaned more often.

1. Perform Pressure Relief Procedure in the Operation

section of this manual.

2. Unscrew the tting (1) from the bottom of the spray

gun using an adjustable wrench, making sure not to

lose the spring (2).

3. Remove the lter (3) from the spray gun housing and

clean with the appropriate cleaning solution (warm,

soapy water for latex paints, mineral spirits for oil-based

materials).

4. Inspect the lter for holes (4). Replace if holes are

found.

3

2

1

5

4

Attention

Never poke the lter with a sharp instrument!

5. Replace the cleaned lter, tapered end rst (5), into

the gun housing. The tapered end of the lter must be

loaded properly into the gun. Improper assembly will

result in a plugged tip or no ow from the gun.

6. Reassemble the spray gun.

PowrLiner 550 17

GB

Cleanup Maintenance

5.5 Cleaning the Sureo™ Valve Assembly

Cleaning or servicing the Sureo Valve may be required if the

unit has priming problems.

1. Remove the siphon tube.

2. Unscrew the inlet valve assembly from the sprayer.

Visually inspect the inside and outside of the Sureo

Valve assembly (1). Clean any paint residue with the

appropriate cleaning solution.

3. Lubricate the o-ring (2) on the Sureo Valve with

petroleum jelly. Replace Sureo valve assembly by

threading it into the sprayer. Torque to 32–38 ft./lbs.

4. Replace the siphon tube and tighten securely.

2

1

i

If priming problems continue, you may need

to replace the Sureo valve. Contact Technical

Service to order a new Sureo Valve assembly.

6. Maintenance

Before proceeding, follow the Pressure Relief

Procedure outlined previously in this manual.

Additionally, follow all other warnings to

reduce the risk of an injection injury, injury

from moving parts or electric shock.

6.1 Adjusting the trigger tension

Use the following procedure to adjust the spring tension of

the trigger lever on the gun holder assembly. The trigger lever

pulls and releases the spray gun trigger when operated from

the spray lever on the cart. The proper tension ensures that

the gun will shut o when the gun trigger is released.

Attention

Always keep the trigger lock on the spray

gun in the locked position while making

adjustments to the system. If necessary, loosen

the gun holder clamp knob and then engage

the spray gun trigger lock. Move the spray gun

to its original position and tighten the clamp

knob.

Before proceeding, follow the Pressure Relief

Procedure outlined previously in this manual.

1. Using a 9/16” (14 mm) hex wrench, loosen the hex

screw on the cable block (1).

2. Move the cable block in the appropriate direction so

there is a maximum of 1/32” (0.8 mm) of movement by

the spray gun trigger (2) and trigger lever (3) before the

spray gun opens.

a. If the trigger lever is pushing on the trigger and opening

the spray gun, slide the cable block toward the gun until

the trigger settles into its normal position. Make sure the

trigger lever is still ush (4) against the trigger.

b. If there is a gap between the trigger lever and the spray gun

lever, slide the cable block away from the gun.

2

3

4

1

18 PowrLiner 550

GB

Maintenance

6.2 Maintaining the Engine

i

For detailed engine specications and

maintenance, refer to the separate engine

manual supplied with this sprayer.

Routine Engine Maintenance

Daily

• Check and ll the gas tank.

• After the rst 20 hours of operation, drain the oil and

rell with clean oil. Check the engine oil level and ll as

necessary.

Weekly

• Remove the cover of the air lter and clean the element.

Replace the element if necessary. If operating in an

unusually dusty environment, check the lter daily and

replace if necessary. (Replacement elements can be

purchased from your local Titan dealer.)

• After each 50 hours of operation: Change the engine oil.

6.3 Safety Shut-O Switch

The safety shut-o switch is pre-set by the factory to shut

down the sprayer to prevent over-pressurization. Do not

attempt to adjust or tamper with the safety shut-o switch.

Contact an authorized service center if this setting requires

adjustment.

i

The safety shut-o switch should be set to shut

down the sprayer between 3200 – 3300 PSI.

6.4 High-pressure hose

Inspect the high-pressure hose visually for any notches or

bulges, in particular at the transition in the ttings. It must be

possible to turn the union nuts freely.

i

The risk of damage rises with the age of

the high-pressure hose. Titan recommends

replacing high-pressure hoses after 6 years.

6.5 Replacing the relief valve

Perform the following procedure using relief valve

replacement kit P/N 759-380.

Before proceeding, follow the Pressure Relief

Procedure outlined previously in this manual.

Additionally, follow all other warnings to

reduce the risk of an injection injury, injury

from moving parts, or electric shock.

1. Pry o the retaining clip (1) from inside the recessed

portion of the valve knob (2). Remove the valve knob.

2. Slide the cam (3) o of the stem/ball assembly (4).

3. Using a wrench, remove the hex nut (5) from the pump

head (6).

4. Remove the star washer (7), spring (8), and stem/ball

assembly (4) from the pump head.

5. Using a 7/32” (6 mm) hex wrench, remove the stem/ball

assembly seat (9) from the pump head.

6

7

4

9

3

8

5

1

2

6. Tighten the new stem/ball assembly seat (9) into the

pump head (6). Use a 7/32” (6 mm) hex wrench. Torque

to 6-8 ft.-lbs.

7. Apply a light coating of hydraulic oil around the o-ring

on the new stem/ball assembly.

8. Push the stem/ball assembly into the stem/ball

assembly seat in the pump head.

9. Place the new spring and star washer around the stem/

ball assembly.

10. Slide the new hex nut onto the stem of the stem/ball

assembly, thread it onto the pump head, and tighten

with a wrench. Torque the nut to 12-14 ft.-lbs.

11. Apply a light coating of grease to the top of the cam.

12. Slide the new cam onto the stem of the stem/ball

assembly and over the hex nut. The design of the cam

will allow the hex nut to t inside the cam, causing the

cam to lock in position.

i

Position the cam on the hex nut so that the tab

(g. 21, item 1) on the side of the cam is as close

to the 12:00 position as possible.

La page est en cours de chargement...

Titan Tool 0290004 Le manuel du propriétaire

Ce manuel convient également à

Titan Tool 0290004 Le manuel du propriétaire

dans d''autres langues

Autres documents