ONFORU ON-GY03-RGBW-US-3 Mode d'emploi

Smart LED Bulb User Guide

English

Deutsch

Français

Español

Lingua Italiana

Section I

General Matters for Attention.

Abschnitt I

Allgemeine Hinweise zur Beachtung.

Section I

Questions générales à l'attention.

Sección I

Cuestiones Generales de Atención.

Primo I

Considerazioni generali.

Section II

Pairing LED bulb To "Smart Life” App.

Abschnitt II

Koppeln der LED-Lampe mit der App "Smart Life"..

Section II

Appairer l’ampoule LED à l'application "Smart Life".

Sección II

Emparejar Bombilla LED a la Aplicación "Smart Life"

Secondo II

Associare le lampadine a LED all'app "Smart Life".

Section III

Controlling Light With Amazon Alexa.

Abschnitt III

Steuern des Lichts mit Amazon Alexa.

Section III

Contrôler la lumière avec Amazon Alexa.

Sección III

Controlando la Luz con Amazon Alexa.

Terzo III

Usa Amazon Alexa per controllare la luce.

Section IV

Controlling Light With Google Assistant.

Abschnitt IV

Licht steuern mit Google Assistant.

Section IV

Contrôler la lumière avec Google Assistant.

Sección IV

Controlando la luz con el Asistente de Google.

Quarto IV

Utilizza l'Assistente Google per controllare le luci.

Pages 1 -2

Seiten 19 - 20

pages 37 - 38

páginas 55 - 56

pagine 73 - 74

Pages 1 - 18

Seiten 19 - 36

pages 37 - 54

páginas 55 - 72

pagine 73 - 90

Pages 3 - 12

Seiten 21 - 30

pages 39 - 48

páginas 57 - 66

pagine 75 - 84

Pages 13 - 15

Seiten 31 - 33

pages 49 - 51

páginas 67 - 69

pagine 85 - 87

Pages 16 - 18

Seiten 34 - 36

pages 52 - 54

páginas 70 - 72

pagine 88 - 90

Catalogue

1

English

ONFORU Smart LED Bulb User Guide

The ONFORU Smart LED Bulb is compatible with both Amazon Alexa and Google Assistant

upon initial installation and pairing of the "Smart Life" App. The "Smart Life" App. can then be

connected to Amazon Alexa or Google Assistant allowing "Voice Control Functionality".

Power on the LED Bulb.

Turn ON/OFF the Smart Bulb three times until the Bulb starts to flash quickly, which indicates

the success of the factory reset.

Follow steps in Section II of the user manual to pair the LED Bulb with the "Smart Life" App.

Congratulations of your purchase of the ONFORU Smart LED Bulb. We encourage you to read

all safety information and instructions before your primary installation of this product.

Factory Reset Procedure

SECTION I – GENERAL MATTERS FOR ATTENTION

This smart LED bulb can only support 2.4 GHz network and cannot work with 5.0 GHz

network.

Please check if your home network is 2.4 GHz and make sure that your phone has been

connected to your Wi-Fi network. Please ensure your network is not hidden.

If you fail to connect the bulb with your Wi-Fi, please check whether your network is stable

and fast. Slow networking speed may result in failure of connection.

If you fail to connect the bulb with your Wi-Fi, please ensure your Wi-Fi password is correct.

If not, please re-enter the correct password.

Wi-Fi Connection Issues

If a router/Wi-Fi password changes or additional smart devices register with the "Smart Life"

App., a factory reset of the ONFORU Smart LED Bulb is required.

If any matters regarding Smart LED Bulb connection happens, you can reset the factory

setting of ONFORU Smart LED Bulb, then re-connect the Smart Bulb.

1.

2.

3.

4.

5.

1.

2.

3.

2

English

PARAMETERS

DIMENSION

Country US UK EU

SKU ON-GY03-RGBW-US-3 ON-GY03-RGBW-UK-3

ON-GY03-RGBW-UK-3

ON-GY03-RGBW-EU-3

Light Base E26 B22 E27

Bulb Type A19 A60 A60

Model MZT-GY001

Quantity 3-Pack

Wattage 7W

Dimmable Yes

Input Voltage 100-240V AC, 50/60Hz

Color Temperature RGB+5000K+3000K

Max. Luminous

Flux

700LM(White Light)

Beaming Angle 270 Degree

Connection Type Wi-Fi

Color RGB, Daylight White, Warm White

94mm / 3.7in

60mm / 2.36in

94mm / 3.7in

60mm / 2.36in

ON-GY03-RGBW-EU-3

ON-GY03-RGBW-US-3

3

English

SECTION II- PAIRING LIGHT BULB WITH"SMART LIFE" App.

"Smart Life" App. installation.

Enter the "Smart Life" App. and register an account and log in.

Step 1

Step 2

There are 2 options for obtaining and installing the "Smart Life" App. on your smart device.

Option 1

Scan the QR code below

After entering the App., the App. will select the your current Country/Region automatically,

and you can choose the Country/Region Manually as well.

A.

Registration

Option 2

Search for "Smart Life" in the App. Store or Google Play.

4

English

Enter your phone number or email

address for registering, and click "Get

Verication Code".

B.

Note:

You will need your "Smart Life" App. username and password to pair with Amazon Alexa and/or

Google Assistant.

Enter the Verication Code you received

and set your own passwords. Click

"DONE".

C,

Logging IN

If you already have an account for Smart Life App., Please select "Log in with existing account".

After entering the App., the App. will select the your current Country/Region automatically,

and you can choose the Country/Region manually.

Enter your phone number or email address with corresponding passwords to log in your

account.

A.

B.

5

English

Add the bulb to Smart Life App.

Step 3

Note: This smart LED bulb can only support 2.4 GHz network and cannot work with 5.0 GHz

network.

Please check if your home network is 2.4 GHz and make sure that your phone has been

connected to your Wi-Fi network. Please ensure your network is not hidden.

(1) Tap "+" button on top right corner to add device, then tap"lighting device" to enter next page.

6

English

(2) Wi-Fi Network Conguration

Smart Life App. supports two kinds of Wi-Fi networks, Normal Mode and Access Points (AP)

Mode. Normal mode is the defaulted option.

If your Wi-Fi signal is weak or slow, or if you can not pair the Smart Bulb with Smart Life

App., you can choose to pair the Bulb via AP mode. In the AP mode, your equipment can

only connect with one bulb each time.

1. Power on the bulb with your own switch.

2. Repeatedly turn ON/OFF the Bulb three times until the bulb flashes quickly.

How to pair the Bulb in 2 Modes.

Normal Mode Setting

7

English

Tap the confirmation button to

pair the Bulb.

3. 4. Enter Wi-Fi password to join your network.

This smart LED bulb can only support 2.4 GHz network and cannot work with 5.0 GHz

network.

Please check if your home network is 2.4 GHz and make sure that your phone has been

connected to your Wi-Fi network. Please ensure your network is not hidden.

Please Note:

a.

b.

5. Wait till it is successfully connected

Note: If the bulb is still flashing until the progress map reaches 100%, the pairing fails, and you

will need to repeat the previous 4 steps to pair the Bulb.

8

English

Power on the bulb with your own

switch.

2.

Repeatedly turn ON/OFF the Bulb

three times until the bulb flashes

quickly.

3.

AP Mode Setting

Tap top right corner to enter AP

mode setting page.

1.

rapid blinking (about 0.5 second per blink)

9

English

5. Enter Wi-Fi password to join your network and tap "Connect Now".

slow blinking (about 3 seconds per blink)

When the Bulb is flashing quickly, repeatedly turn ON/OFF the Bulb three times until the Bulb

flashes slowly (Approximately 3 seconds per time), then tap the conrmation button.

4.

10

English

6. Go to your phone Wi-Fi setting and connect the Wi-Fi named "SmartLife-xxxx".

7. Go back to the App. page and wait till it is successfully connected.

11

English

Step 4

Name the bulb and tap "Done". You will nd the device you’ve named is shown on the App.

homepage. Tap the device to enter the setting page.

Note: The name you give to the device will be the name for voice control on Amazon Alexa or

Google Home later. For example, the device is named "Onforu smart bulb" in this user guide.

12

English

After completing SECTION II, you can now control the light with Smart Life App. on this setting

page.

Note:

If you want to control the light with Amazon Alexa, please continue to read Section III.

If you want to control the light with Google Home, please skip Section II and read Section IV

directly.

Try different functions on the App.

to control the light and have fun.

13

English

Please make sure that your Alexa App. is connected to Amaozn Echo, and both work together

successfully under your Wi-Fi network.

Step A : Log in your Alexa App., tap at the top left corner, and tap "Skills".

SECTION III CONTROLLING LIGHT WITH AMAZON ALEXA

Step B : Type "Smart Life" to search for "Smart Life", and enable "Smart Life" on Alexa.

14

English

Step C : Enter your account and password of Smart Life App., tap "Link Now", then tap

"Authorize" on the next page authorize Smart Life Info to Alexa.

Step D : Once your Smart Life account is successfully connected to Alexa, the following page

will pop up. Tap "Done" on top left corner, then tap "DISCOVER DEVICES" on the next page.

Same account and password

as Smart Life App.

15

English

Step E : Wait a few seconds for Alexa to detect the bulb from Smart Life App., and you will nd

the device named "Onforu Smart Bulb" has been paired to Alexa App. from Smart Life App.

Step F : Now you are able to control the light via Amazon Alexa.

Try these commands and see what happens by asking Alexa :

Alexa, turn on "device name"

Alexa, turn off "device name"

Alexa, set "device name" to "color"

Alexa, set "devcie name" to "number"

For example:

"Alexa, turn on Onforu Smart Bulb", "Alexa, dim Onforu Smart Bulb to 50%" etc.

Note: The device name is the one you give to the bulb on Smart Life App. In this user guide, the

device is named "Onforu smart bulb".

Note: If you also want to control the light with Google Home, You can continue to read Section

IV and learn how to set up.

After step E is done, you can now control the light with Alexa App. on this setting page.

slide to change

brightness

enter to change

colors

tap to turn on/off

the light

16

English

SECTION IV- CONTROLLING LIGHT WITH GOOGLE ASSISTANT

Step A : Open your Google Home App., tap "Home Control" on the Left Side Bar page.

Step B : Tap "+" button on the bottom right corner to enter next page.

Step C : Find "Smart Life" from the side bar list.

17

English

Step D : Enter your account and password of Smart Life App., tap "Link Now", then tap

"Authorize" on the next page to authorize your Smart Life Account Info to Google Home .

Step E : You will nd that Google Home has found the device named "Onforu Smart Bulb" on

this page.

Same account and password

as Smart Life App.

18

English

Step F : Now you are able to control the light via Google Home.

Try these commands and see what happens by asking Google :

ok, Google, turn on "device name"

ok, Google, turn off "device name"

ok, Google, set the "device name" to "color"

ok, Google, set "device name" to "number"

For example:

"ok Google, turn on Onforu smart bulb", "ok Google, dim Onforu smart bulb To 50%" etc.

Note: The device name is the one you give to the bulb on Smart Life App. In this user guide, the

device is named "Onforu smart bulb".

La page charge ...

ONFORU ON-GY03-RGBW-US-3 Mode d'emploi

ONFORU ON-GY03-RGBW-US-3 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents