Philips SM7480 Manuel utilisateur

WWW.SAECO.COM/CARE

SM7583, SM7581

SM7580, SM7480

EN USER MANUAL

DA BRUGERVEJLEDNING

DE BENUTZERHANDBUCH

ES MANUAL DEL USUARIO

FR MODE D’EMPLOI

IT MANUALE UTENTE

NL GEBRUIKSAANWIJZING

NO BRUKERHÅNDBOK

PT MANUAL DO UTILIZADOR

FI KAYTTÖOPAS

SV ANVÄNDARHANDBOK

EL ΕΓΧΕΙΡΙΔΙΟ ΧΡΉΣΉΣ

4219.450.1412.1 XELSIS SM758x GOOD LOW END_WE_FRONTBACKCOVER_A5_FC.indd 1 08/08/2019 13:00

A

12

11

10

9

8

7

6

5

4

3

2

1

A28 A29 A30

A26A25A24 A27

A2 A3 A4

A1

A5

A6

A7

A8A9

A10

A11

A12

A13A14

A15

A16

A18

A19

A17

A20A21A22

A23

Proﬁles

Clean Settings

4 More drinks

Espresso Coﬀee Cappuccino Latte Macchiato Caﬀè Latte Hot WaterAmericano

C

Proﬁles

Clean Settings

6 More drinks

Espresso Coﬀee Cappuccino Latte Macchiato Caﬀè Latte Hot WaterAmericano

BB1

B5B6B7B8B9

C1 C2 C3 C4

C5C6C7C8C9

B3 B4B2

English 6

Dansk 21

Deutsch 37

Español 54

Français 71

Italiano 88

Nederlands 105

Norsk 121

Português 136

Suomi 153

Svenska 168

Ελληνικά 184

English

Contents

Machine overview (Fig. A) ____________________________________________________________________________ 6

Control panel _________________________________________________________________________________________ 7

Introduction __________________________________________________________________________________________ 7

First installation_______________________________________________________________________________________ 7

AquaClean filter ______________________________________________________________________________________ 8

Measuring water hardness___________________________________________________________________________ 8

Brewing drinks________________________________________________________________________________________ 9

Personalizing drinks and creating profiles___________________________________________________________ 10

Adjusting grinder settings ____________________________________________________________________________ 10

Handling the brew group_____________________________________________________________________________ 11

Cleaning and maintenance __________________________________________________________________________ 11

Descaling procedure _________________________________________________________________________________ 14

Error codes ___________________________________________________________________________________________ 15

Ordering accessories _________________________________________________________________________________ 15

Troubleshooting ______________________________________________________________________________________ 16

Technical specifications______________________________________________________________________________ 19

Machine overview (Fig. A)

A1 Control panel A13 Mains cord with plug

A2 Cup holder A14 Grind setting knob

A3 Lid of bean hopper A15 Bean hopper

A4 Lid of pre-ground coffee compartment A16 Brew group

A5 Internal cappuccinatore A17 Inside of service door

A6 Adjustable coffee and milk dispensing spout A18 Coffee funnel

A7 Milk tube holder A19 Coffee residues drawer

A8 Main switch A20 Coffee grounds container

A9 Socket for cord A21 Drip tray

A10 Service door A22 Drip tray cover

A11 'Drip tray full' indicator A23 Water tank

A12 Drip tray release grip

Accessories

A24 Milk container(SM7580, SM7581, SM7583 only) A28 AquaClean filter

A25 Milk tube A29 Measuring scoop

A26 Grease tube A30 Water hardness test strip

A27 Cleaning brush

6English

Control panel

There are multiple versions of this espresso machine, with different control panels. Each version has

its own type number. You can find the type number on the data label on the inside of the service door

(Fig. 16).

Refer to figure B and C for an overview of all buttons and icons. Below you find the description.

Use the up and down arrows to scroll through the display and tap the OK icon to select or confirm

your choices.

SM7580, SM7581, SM7583 only (Fig. B)

B1. On/off button B4. Start/stop button B7. Machine settings

B2. One-touch drink icons B5. Navigation icons (up,

down, back, ok)

B8. Cleaning menu

B3. Menu with 6 more drinks B6. Display B9. Personal profiles

SM7480 only (Fig. C)

C1. On/off button C4. Start/stop button C7. Machine settings

C2. One-touch drink icons C5. Navigation icons (up,

down, back, ok)

C8. Cleaning menu

C3. Menu with 4 more drinks C6. Display C9. Personal profiles

Introduction

Congratulations on your purchase of a Saeco full-automatic coffee machine! To fully benefit from the

support that Saeco offers, please register your product at www.saeco.com/care.

Read the separate safety booklet carefully before you use the machine for the first time and save it for

future reference.

To help you get the best out of your coffee machine, Saeco offers full support in 3 different ways:

1The separate quick start guide for first installation and first use.

2This user manual for more detailed information.

3Online support and movies: scan the QR code on the front page or visit www.saeco.com/care

Note: This machine has been tested with coffee. Although it has been carefully cleaned, there may be

some coffee residues left. We guarantee, however, that the machine is absolutely new.

First installation

To prepare your coffee machine for use, you need to perform a few simple steps such as filling the

water circuit and activating the AquaClean filter. These steps are shown in the separate quick start

guide.

For the best-tasting coffee, you need to brew 5 coffees initially to allow the machine to complete its

self-adjustment.

The machine has been set up to get the best taste out of your coffee beans. Therefore we advise you

not to adjust the grinder settings until you have brewed 100-150 cups (approx. 1 month of usage).

7

English

AquaClean filter

The AquaClean filter is designed to reduce limescale deposits in your coffee machine and provide

filtered water to preserve the aroma and flavor of each cup of coffee. If you use a series of 8

AquaClean filters as indicated by the machine and in this user manual, you don't have to descale your

machine for up to 5000 cups. With each filter you can enjoy up to 625 cups, depending on the

selected coffee varieties and the rinsing and cleaning frequencies.

Preparing the AquaClean filter for activation

Before you place the AquaClean filter in the water tank, you need to prepare it for use:

1 Shake the filter for about 5 seconds (Fig. 1).

2 Fully immerse the filter upside down in a jug with cold water for at least 30 seconds. Wait until no

more air bubbles come out (Fig. 2).

3 Push the filter onto the filter connection to the lowest possible point. (Fig. 3)

Activating the AquaClean filter

You need to activate every new AquaClean filter that you use. By activating the AquaClean filter, the

machine monitors the capacity of the AquaClean filter and the number of filters used. There are 3

ways to activate the AquaClean filter.

1. Activating the AquaClean filter during first installation

After switching on for the first time, the machine guides you through the first installation steps such as

filling the water tank, filling the water circuit and activating the AquaClean filter. Simply follow the

instructions on the screen.

2. Activating the AquaClean filter when prompted

Replace the AquaClean filter when the screen shows the message 'Replace AquaClean filter?'. Then

follow the instructions on the screen to activate the filter properly.

Replace the AquaClean filter at least every 3 months, even if the machine has not yet indicated that

replacement is required.

3. Activating the AquaClean filter at any other time

You can start (re)using the AquaClean filter at any time by following the instructions below.

1Tap the Settings icon and use the up and down icons to select 'AquaClean' (Fig. 4).

2Tap the OK icon. When the activation screen appears, tap the OK icon again.

3Follow the instructions on the screen.

Note: In some situations the machine will tell you that you need to descale the machine before you

can install and activate a new AquaClean filter. This is because your machine has to be completely

limescale-free before you start to use the AquaClean filter. Follow the instructions on the screen.

Measuring water hardness

During first installation, you have to set the water hardness. Follow the steps on the screen and use

the water hardness test strip supplied. To set the water hardness later, tap the Settings icon and

select 'water hardness'.

1Immerse the water hardness test strip in tap water for 1 second. Then wait for 1 minute.

2Check how many squares have turned red.

3Select the appropriate water hardness setting and tap the OK icon to confirm.

8English

Number of red squares:

Value to be set 1 2 3 4

Brewing drinks

You can select a drink by tapping one of the one-touch drink icons (Fig. 5) or by selecting another

drink in the menu by tapping the '6 more drinks' icon (SM7580, SM7581, SM7583 only) or the '4 more

drinks' icon (SM7480 only). After selecting a drink, you can personalize it by adjusting the settings (see

'Personalizing your drinks').

-To brew two cups, first tap a drink and then press the start/stop button twice. You can also brew

two cups by tapping a one-touch drink icon twice. The machine automatically carries out two

grinding cycles in sequence. This is possible for most drinks.

-Tap the profiles icon to brew one of your saved drinks.

-Slide the dispensing spout up or down to adjust the height to the size of the cup or glass you are

using.

Brewing coffee

1Fill the water tank with tap water and fill the bean hopper with beans.

Tip: Slide the dispensing spout to the uppermost position for easy access to the water tank.

2Tap one of the one-touch drink icons (Fig. 5) or tap the '6 more drinks' icon (SM7580, SM7581,

SM7583 only) or the '4 more drinks' icon (SM7480 only) to select another drink.

3Use the up and down arrows (Fig. 6) to adjust the coffee strength. Tap the OK button if you want to

adjust more settings.

4Press the start/stop button at any time to start brewing the selected drink, or after adjusting all

settings tap the OK icon if you want to save your settings to a profile (see 'Creating a profile').

Brewing milk-based drinks

1Fill the water tank with tap water and fill the bean hopper with beans.

Tip: Slide the dispensing spout to the uppermost position for easy access to the water tank.

2 SM7580, SM7581, SM7583: Unscrew the lid of the milk container and fill the milk container with

milk (Fig. 7). Then place the metal milk tube in the container.

SM7480: Place the metal milk tube directly into a milk container.

Always use milk coming directly from the fridge for optimal results.

3Open the door of the internal cappuccinatore (Fig. 8) and connect the flexible milk tube to the

cappuccinatore (Fig. 9). Then close the door of the internal cappuccinatore again.

4Tap one of the one-touch drink icons (Fig. 5) or tap the '6 more drinks' icon (SM7580, SM7581,

SM7583 only) or the '4 more drinks' icon (SM7480 only) to select another drink.

5Tap the OK icon if you want to adjust the settings. You can adjust the settings to your preference

with the up and down arrows (Fig. 6). Tap the OK icon to confirm. Then you can adjust the next

setting.

6After adjusting all settings, tap the OK icon to save your settings to a profile (see 'Creating a

profile').

7Press the start/stop button at any time to start brewing the selected drink.

8Directly after dispensing the milk,the 'Auto Steam Shoot' is performed. The machine forces steam

through the internal milk system to rinse it quickly.

9

English

Brewing coffee with pre-ground coffee

1Open the lid and pour one measuring scoop of pre-ground coffee into the pre-ground coffee

compartment (Fig. 10). Then close the lid.

2After selecting a drink, tap the OK icon and use the up and down arrows to select pre-ground

coffee (Fig. 11). Then press the start/stop button.

Note: If you select ground-coffee, you cannot adjust the coffee strength and brew more than one

drink at the same time.

Dispensing hot water

1Press the one-touch 'Hot water' icon (Fig. 12).

2Press the start/stop button to start dispensing hot water.

Personalizing drinks and creating profiles

This machine allows you to adjust the settings of a drink to your own preference and to save the

adjusted drink in a personal profile. The different profiles have different colours. There are two ways to

create a profile:

1When brewing a drink: Press the OK icon to adjust the settings of the selected drink and after

adjusting all settings tap the OK icon to save the personalized drink to a profile.

2Via the 'Profiles' menu: Select a profile and then personalize the drinks one by one.

Personalizing your drinks

You can adjust the settings to your own preference:

1Tap one of the one-touch drink icons or tap the '6 more drinks' icon (SM7580, SM7581, SM7583

only) or the '4 more drinks' icon (SM7480 only) to select your preferred drink (Fig. 5).

2Tap the OK icon to adjust the settings. The screen shows the settings you can adjust to your

preference. Depending on the type of drink, you can adjust coffee strength, volume of coffee and

milk, coffee temperature and taste.

3Use the up and down arrows to set your preferred level (Fig. 6) and tap the OK icon to confirm.

Depending on the type of drink, the next adjustable setting appears on the screen.

4After customizing all settings, tap the OK icon to save these settings to your profile (Fig. 13) and

follow the instructions on the screen.

Creating a profile

1Tap the Profiles icon repeatedly to select one of the profiles. All profiles have different colors.

You can also use the up and down icons to select your profile.

2Tap the OK icon to customize the profile.

3Use the up and down arrows to select the drink you want to customize and tap the OK icon to

confirm.

4Use the up and down arrows to adjust the settings to your preference and tap the OK icon to

confirm. Customized drinks are marked with an asterisk (*) (Fig. 14).

Adjusting grinder settings

You can adjust the grinder settings by using the grind setting knob inside the bean container. There

are 12 different grind settings you can choose from. The lower the setting, the stronger the coffee.

10 English

Note: You can only adjust the grind settings when the machine is grinding coffee beans. You need to

brew 2 to 3 drinks before you can taste the full difference.

Caution: Do not turn the grind setting knob more than one notch at a time to prevent damage to the

grinder.

1Place a cup under the coffee dispensing spout.

2Open the lid of the bean hopper.

3Tap the ESPRESSO icon. Then press the start/stop button.

4When the grinder starts grinding, press down the grind setting knob and turn it to the left or right

(Fig. 15).

Handling the brew group

Go to www.saeco.com/care for detailed video instructions on how to remove, insert and clean the

brew group.

Removing the brew group from the machine

1Switch off the machine by pressing the main switch on the back of the machine.

2Remove the coffee grounds container.

3Open the service door (Fig. 16).

4Remove the coffee residue drawer (Fig. 17).

5Press the PUSH button (Fig. 18) and pull at the grip of the brew group to remove it from the

machine (Fig. 19).

Reinserting the brew group

Before you slide the brew group back into the machine, make sure it is in the correct position.

1Check if the arrow on the yellow cylinder on the side of the brew group is aligned with the black

arrow and N (Fig. 20).

-If they are not aligned, push down the lever until it is in contact with the base of the brew group

(Fig. 21).

2Make sure that the yellow locking hook on the other side of the brew group is in the correct

position.

-To position the hook correctly, push it upwards until it is in uppermost position (Fig. 22).

3Slide the brew group back into the machine along the guiding rails on the sides until it locks into

position with a click. Do not press the PUSH button.

4Place back the coffee residues drawer and close the service door. Then place back the coffee

grounds container.

Cleaning and maintenance

Regular cleaning and maintenance keeps your machine in top condition and ensures good-tasting

coffee for a long time, a steady coffee flow and a perfect milk froth.

Consult the table on when and how to clean all detachable parts of the machine. You can find more

detailed information and video instructions on www.saeco.com/care.

11

English

Cleaning table

Part description When to clean How to clean

Brew group Weekly Remove the brew group and rinse it under the

tap and let it air-dry.

Monthly Perform the 'Brew group clean' procedure with

the Philips coffee oil remover tablet. Select 'Brew

group clean' in the cleaning menu and follow the

instructions on the screen. Go to

www.saeco.com/care for detailed video

instructions.

Lubrication of the

brew group

Depending on the type of

usage. Consult the

lubrication table (see

'Lubricating the brew group').

Lubricate the brew group with the Philips grease.

Go to www.saeco.com/care for detailed video

instructions.

Milk

system/internal

cappuccinatore

After every day of use Perform the HYGIESTEAM program in the

cleaning menu. Select HYGIESTEAM in the

cleaning menu and follow the instructions on the

screen. Wipe the outside of the metal milk tube

with a damp cloth before placing it into the milk

tube holder.

Weekly Remove and disassemble the internal

cappuccinatore (see 'Cleaning the internal

cappuccinatore under the tap'). Rinse all parts

under the tap with some washing-up liquid.

Monthly Perform the 'DEEP MILK CLEAN' procedure with

the Philips milk circuit cleaner. Select 'DEEP MILK

CLEAN' in the cleaning menu and follow the

instructions on the screen. Go to

www.saeco.com/care for detailed video

instructions.

Milk container

(SM7580, SM7581,

SM7583 only)

Weekly Disassemble the milk container (Fig. 23) and push

the ball out with the measuring scoop (Fig. 24).

Rinse all parts under the tap or in the dishwasher

Drip tray Empty the drip tray every

day or as soon as the red

'drip tray full' indicator pops

up through the drip tray (Fig.

25).

Remove the drip tray and rinse it under the tap

with some washing-up liquid.

Coffee grounds

container

Empty the coffee grounds

container when prompted by

the machine. Clean it weekly.

Remove the coffee grounds container while the

machine is switched on and rinse it under the tap

with some washing-up liquid.

Water tank Weekly Rinse the water tank under the tap

12 English

Part description When to clean How to clean

Coffee funnel Check the coffee funnel

weekly to see if it is clogged.

Unplug the machine and remove the brew group.

Open the lid of the pre-ground coffee

compartment and insert the spoon handle into

the coffee funnel. Move the handle up and down

until the clogged ground coffee falls down (Fig.

26). Go to www.saeco.com.care for detailed

video instructions.

Tip: There is a cleaning calender on the last page of this user manual. Write down the dates on which

you have performed a cleaning action.

Cleaning the brew group

Regular cleaning of the brew group prevents coffee residues from clogging up the internal circuits.

Visit www.saeco.com/care for support videos on how to remove, insert and clean the brew group.

Cleaning the brew group under the tap

1Open the service door and remove the brew group.

2Rinse the brew group thoroughly with water. Carefully clean the upper filter (Fig. 27).

3Let the brew group air-dry before you place it back. Do not dry the brew group with a cloth to

prevent fibers from collecting inside the brew group.

Cleaning the brew group with the coffee oil remover tablets

Only use Philips coffee oil remover tablets. Tap the Clean icon and select 'Brew group clean'. Then

follow the instructions on the screen. Visit www.saeco.com/care for detailed video instructions.

Lubricating the brew group

Lubricate the brew group regularly to ensure that the moving parts continue to move smoothly. See

the table below for the lubrication frequency. Visit www.saeco.com/care for detailed video

instructions.

Usage frequency Nr of drinks brewed daily Lubrication frequency

Low 1-5 Every 4 months

Normal 6-10 Every 2 months

Heavy >10 Every month

Cleaning programs for the internal cappuccinatore

The machines has three programs to clean the internal cappuccinatore. The Auto Steam Shoot

cleaning program is automatically performed by the machine after brewing a milk-based drink. You

can select the HYGIESTEAM or DEEP MILK CLEAN program by tapping the Clean icon and scrolling

through the cleaning menu. Then follow the instructions on the screen.

-Auto Steam Shoot: the machine shoots steam through the internal cappuccinatore to quickly rinse

it.

-HYGIESTEAM: the machine thoroughly cleans the internal milk system with steam. Place the milk

tube in the milk tube holder (Fig. 28) and follow the instructions on the screen.

-DEEP MILK CLEAN: Perform the 'DEEP MILK CLEAN' procedure with the Philips milk circuit cleaner

for a thorough cleaning of the internal milk system.

13

English

Cleaning the internal cappuccinatore under the tap

1Open the door of the internal cappuccinatore (Fig. 8).

2Remove the internal cappuccinatore by pulling it down (Fig. 29).

3Disassemble the internal cappuccinatore by pulling the bottom part off the top part (Fig. 30).

4Disassemble all parts (Fig. 31) and clean them under the tap.

5Reassemble the internal cappuccinatore.

6To place back the internal cappuccinatore, put it in upright position and make sure the holes are

aligned with the two tubes on the machine. Then move the internal cappuccinatore upwards until it

locks into place (Fig. 32).

7Close the door.

Visit www.saeco.com/care for detailed video instructions.

Descaling procedure

Please use Philips descaler only. Under no circumstances should you use a descaler based on sulfuric

acid, hydrochloric acid, sulfamic or acetic acid (vinegar) as this may damage the water circuit in your

machine and not dissolve the limescale properly. Not using the Philips descaler will void your

warranty. Failure to descale the appliance will also void your warranty. You can buy Philips descaling

solution in the online shop at www.saeco.com/care.

1When the machine asks you to descale it, press the start/stop button to start. To start descaling

without being prompted by the machine, tap the Clean icon and select 'Descale'.

2Remove the drip tray and the coffee grounds container, empty them and put them back into place.

3Remove the water tank and empty it. Then remove the AquaClean filter.

4Pour the whole bottle of Philips descaler in the water tank and then fill it with water up to the CALC

CLEAN level. Then place it back into the machine.

5Place a large container (1.5 l) under the coffee dispensing spout.

6Place the milk tube on the milk tube holder.

7Follow the instructions on the screen to start the descaling procedure. The descaling procedure

lasts approx. 30 minutes and consists of a descaling cycle and a rinsing cycle.

8Once the descaling cycle is finished, you need to rinse the water tank and water circuit. Follow the

instructions on the screen.

9Place a new AquaClean filter in the water tank.

Tip: Using the AquaClean filter reduces the need for descaling!

What to do if the descaling procedure is interrupted

You can exit the descaling procedure by pressing the on/off button on the control panel. If the

descaling procedure is interrupted before it is completely finished, do the following:

1Empty and rinse the water tank thoroughly.

2Fill the water tank with fresh water up to the CALC CLEAN level indication and switch the machine

back on. The machine will heat up and perform an automatic rinsing cycle.

3Before brewing any drinks, perform a manual rinsing cycle. To perform a manual rinsing cycle, first

dispense half a water tank of hot water and then brew 2 cups of pre-ground coffee without adding

ground coffee.

Note: If the descaling procedure was not completed, the machine will require another descaling

procedure as soon as possible.

14 English

Error codes

Below you find a list of the error codes showing problems that you can solve yourself. Video

instructions are available on www.saeco.com/care. If another error code appears, please contact the

Philips Consumer Care Center in your country. For contact details, see the warranty leaflet.

Error

code Problem Possible solution

01 The coffee funnel is

clogged.

Switch off the machine and unplug it. Remove the brew group.

Then open the lid of the pre-ground coffee compartment and

insert the spoon handle. Move the handle up and down until

the clogged ground coffee falls down (Fig. 26). Visit

www.saeco.com/care for detailed video instructions.

03 The brew group is dirty

or not well-greased.

Switch off the machine with the main switch. Rinse the brew

group with fresh water, let it air-dry and then lubricate it.

Consult chapter 'Cleaning the brew group' or visit

www.saeco.com/care for detailed video instructions. Then

switch the machine on again.

04 The brew group is not

positioned correctly.

Switch off the machine with the main switch. Remove the brew

group and reinsert it. Make sure that the brew group is in the

correct position before you insert it. Consult chapter 'Handling

the brew group or visit www.saeco.com/care for detailed

video instructions. Then switch the machine on again.

05 There is air in the water

circuit.

Restart the machine by switching it off and on again with the

main switch. If this works, dispense 2-3 cups of hot water.

Descale the machine if you have not done so for a longer

period of time.

The AquaClean filter

was not prepared

properly before

installation or it is

clogged.

Remove the AquaClean filter and try again to brew a coffee. If

this works, make sure that the AquaClean filter is prepared

properly before you place it back (see 'Preparing the

AquaClean filter for activation'). Put the AquaClean filter back

into the water tank. If this still does not work, the filter might be

clogged and needs to be replaced.

14 The machine is

overheated.

Switch the machine off and switch it back on again after 30

minutes.

Ordering accessories

To clean and descale the machine, only use the Philips maintenance products. These products can be

purchased from your local retailer, from the authorized service centers or online at

www.saeco.com/care. To find a full list of spare parts online, enter the model number of your

machine. You can find the model number on the inside of the service door.

Maintenance products and type numbers:

-Descaling solution CA6700

-AquaClean filter CA6903

-Brew group grease HD5061

-Coffee oil remover tablets CA6704

-Milk circuit cleaner CA6705

-Maintenance kit CA6707

15

English

Troubleshooting

This chapter summarizes the most common problems you could encounter with the machine. Support

videos and a complete list of frequently asked questions are available on www.saeco.com/care. If you

are unable to solve the problem, contact the Consumer Care Center in your country. For contact

details, see the warranty leaflet.

Problem Cause Solution

The drip tray fills up

quickly.

This is normal. The machine

uses water to rinse the internal

circuit and brew group. Some

water flows through the internal

system directly into the drip

tray.

Empty the drip tray every day or as

soon as the red 'drip tray full' indicator

pops up through the drip tray (Fig. 25).

Place a cup under the dispensing spout

to collect rinsing water.

The machine is in DEMO

mode.

You pressed the standby

button for more than 8

seconds.

Switch the machine off and then on

again with the main switch on the back

of the machine.

The 'coffee grounds

container full' icon

remains displayed.

You emptied the coffee

grounds container while the

machine was switched off.

Always empty the coffee grounds

container while the machine is switched

on. If you empty the coffee grounds

container when the machine is switched

off, the coffee cycle counter is not reset.

You placed back the coffee

grounds container too fast.

Do not place back the coffee grounds

container until the screen prompts you

to put it back.

The 'coffee grounds

container full' icon is

displayed even though

the container is not full.

The machine did not reset the

counter the last time you

emptied the coffee grounds

container.

Always wait approx. 5 seconds when

you place back the coffee grounds

container.In this way the coffee

grounds counter will be reset to zero.

Always empty the coffee grounds

container while the machine is switched

on. If you empty the coffee grounds

container when the machine is switched

off, the coffee grounds counter will not

be reset.

I cannot remove the

brew group.

The brew group is not in the

correct position.

Reset the machine in the following way:

place back the drip tray and the coffee

grounds container. Then close the

service door and switch the machine off

and back on again. Try again to remove

the brew group.

You have not removed the

coffee grounds container.

Remove the coffee grounds container

before you remove the brew group.

16 English

Problem Cause Solution

I cannot insert the brew

group.

The brew group is not in the

correct position.

Reset the machine in the following way:

place back the drip tray and the coffee

grounds container. Leave the brew

group out. Close the service door and

switch the machine on and off. Then put

the brew group in the correct position

and reinsert it into in the machine.

The coffee is watery. The brew group is dirty or

needs to be lubricated.

Clean and lubricate the brew group.

The grinder is set to a too

coarse setting.

Set the grinder to a finer (lower) setting.

The coffee settings have been

adjusted.

Select your coffee drink and adjust the

settings to a stronger coffee.

The machine is performing its

self-adjustment procedure

after a change in grinder

settings or bean types.

Brew a few cups of coffee.

The coffee is not hot

enough.

The cups you use are cold. Preheat the cups by rinsing them with

hot water.

The temperature is set too low.

Check the menu settings.

Set the temperature to 'high' in the

menu.

You added milk. Whether the milk you add is warm or

cold, it always decreases the

temperature of the coffee to some

extent.

Coffee does not come

out or coffee comes out

slowly.

The AquaClean filter was not

prepared properly for

installation or it is clogged.

Remove the AquaClean filter and try to

brew a coffee again. If this works, make

sure the AquaClean filter is prepared

properly before you place it back. Place

back the prepared filter. If this still does

not work, the filter might be clogged

and needs to be replaced.

The grinder is set to a too fine

setting.

Set the grinder to a coarser (higher)

setting.

The brew group is dirty. Clean the brew group.

The coffee dispensing spout is

dirty.

Clean the coffee dispensing spout and

its holes with a needle.

The machine circuit is blocked

by limescale.

Descale the machine.

The milk does not froth. The internal cappuccinatore is

dirty or not inserted correctly.

Clean the internal cappuccinatore and

make sure that you position and insert it

correctly (see 'Cleaning the internal

cappuccinatore under the tap').

17

English

Problem Cause Solution

The type of milk used is not

suitable for frothing.

Different types of milk result in different

amounts of froth and different froth

qualities. We have tested the following

milk types which proved to deliver a

good milk froth result: semi-skimmed or

full-fat cow's milk, soy milk and lactose-

free milk.

The milk is splashing. The milk you use is not cold

enough.

Make sure you use cold milk coming

directly from the fridge.

The flexible milk tube is not

connected properly.

Open the door of the coffee dispensing

spout (Fig. 8) and check if the flexible

milk tube is fully connected to the

cappuccinatore (Fig. 9). Note that the

cappuccinatore and milk tubes may be

hot. Let the cappuccinatore and the

tubes cool down before you touch

them.

The cappuccinatore and milk

tubes are not clean.

Remove and disassemble the internal

cappuccinatore (see 'Cleaning the

internal cappuccinatore under the tap').

Rinse all parts under the tap. For a

thorough cleaning, use the Philips milk

circuit cleaner and perform the DEEP

MILK CLEAN procedure via the cleaning

( ) menu. Note that if the parts have

been cleaned in the dishwasher, they

may have become clogged by food

particles or detergent residues. A visual

check that they are not obstructed is

also recommended.

We advise you to perform the

HygieSteam program every day: 1) Press

'Clean' on the control panel. 2) Select

'HygieSteam'. 3) Press the start button

to start the process, then confirm all

steps on the display.

The milk tubes are clogged. Always store the milk container without

the milk tubes in the refrigerator.

Leftover milk could accumulate within

the milk tubes and block the flow of

milk going through the tubes. Rinse the

milk tubes before storage.

The machine seems to

be leaking.

The machine uses water to

rinse the internal circuit and

brew group. Some water flows

through the internal system

directly into the drip tray.

Empty the drip tray every day or as

soon as the 'drip tray full' indicator pops

up through the drip tray cover (Fig. 25).

Place a cup under the dispensing spout

to collect rinsing water.

18 English

Problem Cause Solution

The drip tray is too full and has

overflowed which makes it look

like the machine is leaking.

Empty the drip tray every day or as

soon as the 'drip tray full' indicator pops

up through the drip tray cover (Fig. 25).

Place a cup under the dispensing spout

to collect rinsing water.

The machine is not placed on a

horizontal surface.

Place the machine on a horizontal

surface so that the 'drip tray full'

indicator works properly.

I cannot activate the

AquaClean filter and the

machine asks for

descaling.

The filter has not been replaced

in time after the AquaClean

filter icon flashed and the

capacity dropped to 0%.

Descale your machine first and then

install the AquaClean filter.

You did not install the

AquaClean filter during first

installation, but after having

brewed approx. 25 coffees

(based on 100ml/3oz cups). The

machine has to be completely

limescale-free before you

install the AquaClean filter.

First descale the machine and then

install a new AquaClean filter. After

descaling, the filter counter is reset to

0/8. Always confirm filter activation in

the machine menu. Also do this after

filter replacement.

The new water filter does

not fit.

You are trying to install another

filter than the AquaClean filter.

Only the AquaClean filter fits into the

machine.

The machine is making a

noise.

It is normal that your machine

makes noise during use.

If the machine starts to make a different

kind of noise, clean the brew group and

lubricate it (see 'Lubricating the brew

group').

The AquaClean filter was not

prepared properly and air is

now drawn into the machine.

Remove the AquaClean filter from the

water tank. Shake the filter for about 5

seconds. Immerse the filter upside

down in a jug with cold water for at

least 30 seconds. Wait until no more air

bubbles come out. Place the prepared

AquaClean filter back into the water

tank. Then dispense 2-3 cups of hot

water.

19

English

Water tank 1.7 litres, removable

Coffee bean hopper capacity 450 g

Coffee grounds container capacity 15 pucks

Milk container capacity (SM7580, SM7581.

SM7583 only)

600 ml

Adjustable spout height 75-148 mm

Nominal voltage - Power rating - Power supply See data plate on inside of service door

20 English

Technical specifications

The manufacturer reserves the right to improve the technical specifications of the product. All the

preset quantities are approximate.

Description Value

Size (w x h x d) 283 x 393 x 489 mm

Weight 10.8 - 12.2 kg

Power cord length 1200 mm

La page charge ...

Philips SM7480 Manuel utilisateur

Philips SM7480 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents