Philips SM7480 Manuel utilisateur

Catégorie
Cafetières
Taper
Manuel utilisateur
WWW.SAECO.COM/CARE
SM7583, SM7581
SM7580, SM7480
EN USER MANUAL
DA BRUGERVEJLEDNING
DE BENUTZERHANDBUCH
ES MANUAL DEL USUARIO
FR MODE D’EMPLOI
IT MANUALE UTENTE
NL GEBRUIKSAANWIJZING
NO BRUKERHÅNDBOK
PT MANUAL DO UTILIZADOR
FI KAYTTÖOPAS
SV ANVÄNDARHANDBOK
EL ΕΓΧΕΙΡΙΔΙΟ ΧΡΉΣΉΣ
4219.450.1412.1 XELSIS SM758x GOOD LOW END_WE_FRONTBACKCOVER_A5_FC.indd 1 08/08/2019 13:00
A
12
11
10
9
8
7
6
5
4
3
2
1
A28 A29 A30
A26A25A24 A27
A2 A3 A4
A1
A5
A6
A7
A7
A8A9
A10
A11
A12
A13A14
A15
A16
A18
A19
A17
A20A21A22
A23
Profiles
Clean Settings
4 More drinks
Espresso Coffee Cappuccino Latte Macchiato Caè Latte Hot WaterAmericano
C
Profiles
Clean Settings
6 More drinks
Espresso Coffee Cappuccino Latte Macchiato Caè Latte Hot WaterAmericano
BB1
B5B6B7B8B9
C1 C2 C3 C4
C5C6C7C8C9
B3 B4B2
English 6
Dansk 21
Deutsch 37
Español 54
Français 71
Italiano 88
Nederlands 105
Norsk 121
Português 136
Suomi 153
Svenska 168
Ελληνικά 184
English
Contents
Machine overview (Fig. A) ____________________________________________________________________________ 6
Control panel _________________________________________________________________________________________ 7
Introduction __________________________________________________________________________________________ 7
First installation_______________________________________________________________________________________ 7
AquaClean filter ______________________________________________________________________________________ 8
Measuring water hardness___________________________________________________________________________ 8
Brewing drinks________________________________________________________________________________________ 9
Personalizing drinks and creating profiles___________________________________________________________ 10
Adjusting grinder settings ____________________________________________________________________________ 10
Handling the brew group_____________________________________________________________________________ 11
Cleaning and maintenance __________________________________________________________________________ 11
Descaling procedure _________________________________________________________________________________ 14
Error codes ___________________________________________________________________________________________ 15
Ordering accessories _________________________________________________________________________________ 15
Troubleshooting ______________________________________________________________________________________ 16
Technical specifications______________________________________________________________________________ 19
Machine overview (Fig. A)
A1 Control panel A13 Mains cord with plug
A2 Cup holder A14 Grind setting knob
A3 Lid of bean hopper A15 Bean hopper
A4 Lid of pre-ground coffee compartment A16 Brew group
A5 Internal cappuccinatore A17 Inside of service door
A6 Adjustable coffee and milk dispensing spout A18 Coffee funnel
A7 Milk tube holder A19 Coffee residues drawer
A8 Main switch A20 Coffee grounds container
A9 Socket for cord A21 Drip tray
A10 Service door A22 Drip tray cover
A11 'Drip tray full' indicator A23 Water tank
A12 Drip tray release grip
Accessories
A24 Milk container(SM7580, SM7581, SM7583 only) A28 AquaClean filter
A25 Milk tube A29 Measuring scoop
A26 Grease tube A30 Water hardness test strip
A27 Cleaning brush
6English
Control panel
There are multiple versions of this espresso machine, with different control panels. Each version has
its own type number. You can find the type number on the data label on the inside of the service door
(Fig. 16).
Refer to figure B and C for an overview of all buttons and icons. Below you find the description.
Use the up and down arrows to scroll through the display and tap the OK icon to select or confirm
your choices.
SM7580, SM7581, SM7583 only (Fig. B)
B1. On/off button B4. Start/stop button B7. Machine settings
B2. One-touch drink icons B5. Navigation icons (up,
down, back, ok)
B8. Cleaning menu
B3. Menu with 6 more drinks B6. Display B9. Personal profiles
SM7480 only (Fig. C)
C1. On/off button C4. Start/stop button C7. Machine settings
C2. One-touch drink icons C5. Navigation icons (up,
down, back, ok)
C8. Cleaning menu
C3. Menu with 4 more drinks C6. Display C9. Personal profiles
Introduction
Congratulations on your purchase of a Saeco full-automatic coffee machine! To fully benefit from the
support that Saeco offers, please register your product at www.saeco.com/care.
Read the separate safety booklet carefully before you use the machine for the first time and save it for
future reference.
To help you get the best out of your coffee machine, Saeco offers full support in 3 different ways:
1The separate quick start guide for first installation and first use.
2This user manual for more detailed information.
3Online support and movies: scan the QR code on the front page or visit www.saeco.com/care
Note: This machine has been tested with coffee. Although it has been carefully cleaned, there may be
some coffee residues left. We guarantee, however, that the machine is absolutely new.
First installation
To prepare your coffee machine for use, you need to perform a few simple steps such as filling the
water circuit and activating the AquaClean filter. These steps are shown in the separate quick start
guide.
For the best-tasting coffee, you need to brew 5 coffees initially to allow the machine to complete its
self-adjustment.
The machine has been set up to get the best taste out of your coffee beans. Therefore we advise you
not to adjust the grinder settings until you have brewed 100-150 cups (approx. 1 month of usage).
7
English
AquaClean filter
The AquaClean filter is designed to reduce limescale deposits in your coffee machine and provide
filtered water to preserve the aroma and flavor of each cup of coffee. If you use a series of 8
AquaClean filters as indicated by the machine and in this user manual, you don't have to descale your
machine for up to 5000 cups. With each filter you can enjoy up to 625 cups, depending on the
selected coffee varieties and the rinsing and cleaning frequencies.
Preparing the AquaClean filter for activation
Before you place the AquaClean filter in the water tank, you need to prepare it for use:
1 Shake the filter for about 5 seconds (Fig. 1).
2 Fully immerse the filter upside down in a jug with cold water for at least 30 seconds. Wait until no
more air bubbles come out (Fig. 2).
3 Push the filter onto the filter connection to the lowest possible point. (Fig. 3)
Activating the AquaClean filter
You need to activate every new AquaClean filter that you use. By activating the AquaClean filter, the
machine monitors the capacity of the AquaClean filter and the number of filters used. There are 3
ways to activate the AquaClean filter.
1. Activating the AquaClean filter during first installation
After switching on for the first time, the machine guides you through the first installation steps such as
filling the water tank, filling the water circuit and activating the AquaClean filter. Simply follow the
instructions on the screen.
2. Activating the AquaClean filter when prompted
Replace the AquaClean filter when the screen shows the message 'Replace AquaClean filter?'. Then
follow the instructions on the screen to activate the filter properly.
Replace the AquaClean filter at least every 3 months, even if the machine has not yet indicated that
replacement is required.
3. Activating the AquaClean filter at any other time
You can start (re)using the AquaClean filter at any time by following the instructions below.
1Tap the Settings icon and use the up and down icons to select 'AquaClean' (Fig. 4).
2Tap the OK icon. When the activation screen appears, tap the OK icon again.
3Follow the instructions on the screen.
Note: In some situations the machine will tell you that you need to descale the machine before you
can install and activate a new AquaClean filter. This is because your machine has to be completely
limescale-free before you start to use the AquaClean filter. Follow the instructions on the screen.
Measuring water hardness
During first installation, you have to set the water hardness. Follow the steps on the screen and use
the water hardness test strip supplied. To set the water hardness later, tap the Settings icon and
select 'water hardness'.
1Immerse the water hardness test strip in tap water for 1 second. Then wait for 1 minute.
2Check how many squares have turned red.
3Select the appropriate water hardness setting and tap the OK icon to confirm.
8English
Number of red squares:
Value to be set 1 2 3 4
Brewing drinks
You can select a drink by tapping one of the one-touch drink icons (Fig. 5) or by selecting another
drink in the menu by tapping the '6 more drinks' icon (SM7580, SM7581, SM7583 only) or the '4 more
drinks' icon (SM7480 only). After selecting a drink, you can personalize it by adjusting the settings (see
'Personalizing your drinks').
-To brew two cups, first tap a drink and then press the start/stop button twice. You can also brew
two cups by tapping a one-touch drink icon twice. The machine automatically carries out two
grinding cycles in sequence. This is possible for most drinks.
-Tap the profiles icon to brew one of your saved drinks.
-Slide the dispensing spout up or down to adjust the height to the size of the cup or glass you are
using.
Brewing coffee
1Fill the water tank with tap water and fill the bean hopper with beans.
Tip: Slide the dispensing spout to the uppermost position for easy access to the water tank.
2Tap one of the one-touch drink icons (Fig. 5) or tap the '6 more drinks' icon (SM7580, SM7581,
SM7583 only) or the '4 more drinks' icon (SM7480 only) to select another drink.
3Use the up and down arrows (Fig. 6) to adjust the coffee strength. Tap the OK button if you want to
adjust more settings.
4Press the start/stop button at any time to start brewing the selected drink, or after adjusting all
settings tap the OK icon if you want to save your settings to a profile (see 'Creating a profile').
Brewing milk-based drinks
1Fill the water tank with tap water and fill the bean hopper with beans.
Tip: Slide the dispensing spout to the uppermost position for easy access to the water tank.
2 SM7580, SM7581, SM7583: Unscrew the lid of the milk container and fill the milk container with
milk (Fig. 7). Then place the metal milk tube in the container.
SM7480: Place the metal milk tube directly into a milk container.
Always use milk coming directly from the fridge for optimal results.
3Open the door of the internal cappuccinatore (Fig. 8) and connect the flexible milk tube to the
cappuccinatore (Fig. 9). Then close the door of the internal cappuccinatore again.
4Tap one of the one-touch drink icons (Fig. 5) or tap the '6 more drinks' icon (SM7580, SM7581,
SM7583 only) or the '4 more drinks' icon (SM7480 only) to select another drink.
5Tap the OK icon if you want to adjust the settings. You can adjust the settings to your preference
with the up and down arrows (Fig. 6). Tap the OK icon to confirm. Then you can adjust the next
setting.
6After adjusting all settings, tap the OK icon to save your settings to a profile (see 'Creating a
profile').
7Press the start/stop button at any time to start brewing the selected drink.
8Directly after dispensing the milk,the 'Auto Steam Shoot' is performed. The machine forces steam
through the internal milk system to rinse it quickly.
9
English
Brewing coffee with pre-ground coffee
1Open the lid and pour one measuring scoop of pre-ground coffee into the pre-ground coffee
compartment (Fig. 10). Then close the lid.
2After selecting a drink, tap the OK icon and use the up and down arrows to select pre-ground
coffee (Fig. 11). Then press the start/stop button.
Note: If you select ground-coffee, you cannot adjust the coffee strength and brew more than one
drink at the same time.
Dispensing hot water
1Press the one-touch 'Hot water' icon (Fig. 12).
2Press the start/stop button to start dispensing hot water.
Personalizing drinks and creating profiles
This machine allows you to adjust the settings of a drink to your own preference and to save the
adjusted drink in a personal profile. The different profiles have different colours. There are two ways to
create a profile:
1When brewing a drink: Press the OK icon to adjust the settings of the selected drink and after
adjusting all settings tap the OK icon to save the personalized drink to a profile.
2Via the 'Profiles' menu: Select a profile and then personalize the drinks one by one.
Personalizing your drinks
You can adjust the settings to your own preference:
1Tap one of the one-touch drink icons or tap the '6 more drinks' icon (SM7580, SM7581, SM7583
only) or the '4 more drinks' icon (SM7480 only) to select your preferred drink (Fig. 5).
2Tap the OK icon to adjust the settings. The screen shows the settings you can adjust to your
preference. Depending on the type of drink, you can adjust coffee strength, volume of coffee and
milk, coffee temperature and taste.
3Use the up and down arrows to set your preferred level (Fig. 6) and tap the OK icon to confirm.
Depending on the type of drink, the next adjustable setting appears on the screen.
4After customizing all settings, tap the OK icon to save these settings to your profile (Fig. 13) and
follow the instructions on the screen.
Creating a profile
1Tap the Profiles icon repeatedly to select one of the profiles. All profiles have different colors.
You can also use the up and down icons to select your profile.
2Tap the OK icon to customize the profile.
3Use the up and down arrows to select the drink you want to customize and tap the OK icon to
confirm.
4Use the up and down arrows to adjust the settings to your preference and tap the OK icon to
confirm. Customized drinks are marked with an asterisk (*) (Fig. 14).
Adjusting grinder settings
You can adjust the grinder settings by using the grind setting knob inside the bean container. There
are 12 different grind settings you can choose from. The lower the setting, the stronger the coffee.
10 English
Note: You can only adjust the grind settings when the machine is grinding coffee beans. You need to
brew 2 to 3 drinks before you can taste the full difference.
Caution: Do not turn the grind setting knob more than one notch at a time to prevent damage to the
grinder.
1Place a cup under the coffee dispensing spout.
2Open the lid of the bean hopper.
3Tap the ESPRESSO icon. Then press the start/stop button.
4When the grinder starts grinding, press down the grind setting knob and turn it to the left or right
(Fig. 15).
Handling the brew group
Go to www.saeco.com/care for detailed video instructions on how to remove, insert and clean the
brew group.
Removing the brew group from the machine
1Switch off the machine by pressing the main switch on the back of the machine.
2Remove the coffee grounds container.
3Open the service door (Fig. 16).
4Remove the coffee residue drawer (Fig. 17).
5Press the PUSH button (Fig. 18) and pull at the grip of the brew group to remove it from the
machine (Fig. 19).
Reinserting the brew group
Before you slide the brew group back into the machine, make sure it is in the correct position.
1Check if the arrow on the yellow cylinder on the side of the brew group is aligned with the black
arrow and N (Fig. 20).
-If they are not aligned, push down the lever until it is in contact with the base of the brew group
(Fig. 21).
2Make sure that the yellow locking hook on the other side of the brew group is in the correct
position.
-To position the hook correctly, push it upwards until it is in uppermost position (Fig. 22).
3Slide the brew group back into the machine along the guiding rails on the sides until it locks into
position with a click. Do not press the PUSH button.
4Place back the coffee residues drawer and close the service door. Then place back the coffee
grounds container.
Cleaning and maintenance
Regular cleaning and maintenance keeps your machine in top condition and ensures good-tasting
coffee for a long time, a steady coffee flow and a perfect milk froth.
Consult the table on when and how to clean all detachable parts of the machine. You can find more
detailed information and video instructions on www.saeco.com/care.
11
English
Cleaning table
Cleaning table
Part description When to clean How to clean
Brew group Weekly Remove the brew group and rinse it under the
tap and let it air-dry.
Monthly Perform the 'Brew group clean' procedure with
the Philips coffee oil remover tablet. Select 'Brew
group clean' in the cleaning menu and follow the
instructions on the screen. Go to
www.saeco.com/care for detailed video
instructions.
Lubrication of the
brew group
Depending on the type of
usage. Consult the
lubrication table (see
'Lubricating the brew group').
Lubricate the brew group with the Philips grease.
Go to www.saeco.com/care for detailed video
instructions.
Milk
system/internal
cappuccinatore
After every day of use Perform the HYGIESTEAM program in the
cleaning menu. Select HYGIESTEAM in the
cleaning menu and follow the instructions on the
screen. Wipe the outside of the metal milk tube
with a damp cloth before placing it into the milk
tube holder.
Weekly Remove and disassemble the internal
cappuccinatore (see 'Cleaning the internal
cappuccinatore under the tap'). Rinse all parts
under the tap with some washing-up liquid.
Monthly Perform the 'DEEP MILK CLEAN' procedure with
the Philips milk circuit cleaner. Select 'DEEP MILK
CLEAN' in the cleaning menu and follow the
instructions on the screen. Go to
www.saeco.com/care for detailed video
instructions.
Milk container
(SM7580, SM7581,
SM7583 only)
Weekly Disassemble the milk container (Fig. 23) and push
the ball out with the measuring scoop (Fig. 24).
Rinse all parts under the tap or in the dishwasher
Drip tray Empty the drip tray every
day or as soon as the red
'drip tray full' indicator pops
up through the drip tray (Fig.
25).
Remove the drip tray and rinse it under the tap
with some washing-up liquid.
Coffee grounds
container
Empty the coffee grounds
container when prompted by
the machine. Clean it weekly.
Remove the coffee grounds container while the
machine is switched on and rinse it under the tap
with some washing-up liquid.
Water tank Weekly Rinse the water tank under the tap
12 English
Part description When to clean How to clean
Coffee funnel Check the coffee funnel
weekly to see if it is clogged.
Unplug the machine and remove the brew group.
Open the lid of the pre-ground coffee
compartment and insert the spoon handle into
the coffee funnel. Move the handle up and down
until the clogged ground coffee falls down (Fig.
26). Go to www.saeco.com.care for detailed
video instructions.
Tip: There is a cleaning calender on the last page of this user manual. Write down the dates on which
you have performed a cleaning action.
Cleaning the brew group
Regular cleaning of the brew group prevents coffee residues from clogging up the internal circuits.
Visit www.saeco.com/care for support videos on how to remove, insert and clean the brew group.
Cleaning the brew group under the tap
1Open the service door and remove the brew group.
2Rinse the brew group thoroughly with water. Carefully clean the upper filter (Fig. 27).
3Let the brew group air-dry before you place it back. Do not dry the brew group with a cloth to
prevent fibers from collecting inside the brew group.
Cleaning the brew group with the coffee oil remover tablets
Only use Philips coffee oil remover tablets. Tap the Clean icon and select 'Brew group clean'. Then
follow the instructions on the screen. Visit www.saeco.com/care for detailed video instructions.
Lubricating the brew group
Lubricate the brew group regularly to ensure that the moving parts continue to move smoothly. See
the table below for the lubrication frequency. Visit www.saeco.com/care for detailed video
instructions.
Usage frequency Nr of drinks brewed daily Lubrication frequency
Low 1-5 Every 4 months
Normal 6-10 Every 2 months
Heavy >10 Every month
Cleaning programs for the internal cappuccinatore
The machines has three programs to clean the internal cappuccinatore. The Auto Steam Shoot
cleaning program is automatically performed by the machine after brewing a milk-based drink. You
can select the HYGIESTEAM or DEEP MILK CLEAN program by tapping the Clean icon and scrolling
through the cleaning menu. Then follow the instructions on the screen.
-Auto Steam Shoot: the machine shoots steam through the internal cappuccinatore to quickly rinse
it.
-HYGIESTEAM: the machine thoroughly cleans the internal milk system with steam. Place the milk
tube in the milk tube holder (Fig. 28) and follow the instructions on the screen.
-DEEP MILK CLEAN: Perform the 'DEEP MILK CLEAN' procedure with the Philips milk circuit cleaner
for a thorough cleaning of the internal milk system.
13
English
Cleaning the internal cappuccinatore under the tap
1Open the door of the internal cappuccinatore (Fig. 8).
2Remove the internal cappuccinatore by pulling it down (Fig. 29).
3Disassemble the internal cappuccinatore by pulling the bottom part off the top part (Fig. 30).
4Disassemble all parts (Fig. 31) and clean them under the tap.
5Reassemble the internal cappuccinatore.
6To place back the internal cappuccinatore, put it in upright position and make sure the holes are
aligned with the two tubes on the machine. Then move the internal cappuccinatore upwards until it
locks into place (Fig. 32).
7Close the door.
Visit www.saeco.com/care for detailed video instructions.
Descaling procedure
Please use Philips descaler only. Under no circumstances should you use a descaler based on sulfuric
acid, hydrochloric acid, sulfamic or acetic acid (vinegar) as this may damage the water circuit in your
machine and not dissolve the limescale properly. Not using the Philips descaler will void your
warranty. Failure to descale the appliance will also void your warranty. You can buy Philips descaling
solution in the online shop at www.saeco.com/care.
1When the machine asks you to descale it, press the start/stop button to start. To start descaling
without being prompted by the machine, tap the Clean icon and select 'Descale'.
2Remove the drip tray and the coffee grounds container, empty them and put them back into place.
3Remove the water tank and empty it. Then remove the AquaClean filter.
4Pour the whole bottle of Philips descaler in the water tank and then fill it with water up to the CALC
CLEAN level. Then place it back into the machine.
5Place a large container (1.5 l) under the coffee dispensing spout.
6Place the milk tube on the milk tube holder.
7Follow the instructions on the screen to start the descaling procedure. The descaling procedure
lasts approx. 30 minutes and consists of a descaling cycle and a rinsing cycle.
8Once the descaling cycle is finished, you need to rinse the water tank and water circuit. Follow the
instructions on the screen.
9Place a new AquaClean filter in the water tank.
Tip: Using the AquaClean filter reduces the need for descaling!
What to do if the descaling procedure is interrupted
You can exit the descaling procedure by pressing the on/off button on the control panel. If the
descaling procedure is interrupted before it is completely finished, do the following:
1Empty and rinse the water tank thoroughly.
2Fill the water tank with fresh water up to the CALC CLEAN level indication and switch the machine
back on. The machine will heat up and perform an automatic rinsing cycle.
3Before brewing any drinks, perform a manual rinsing cycle. To perform a manual rinsing cycle, first
dispense half a water tank of hot water and then brew 2 cups of pre-ground coffee without adding
ground coffee.
Note: If the descaling procedure was not completed, the machine will require another descaling
procedure as soon as possible.
14 English
Error codes
Below you find a list of the error codes showing problems that you can solve yourself. Video
instructions are available on www.saeco.com/care. If another error code appears, please contact the
Philips Consumer Care Center in your country. For contact details, see the warranty leaflet.
Error
code Problem Possible solution
01 The coffee funnel is
clogged.
Switch off the machine and unplug it. Remove the brew group.
Then open the lid of the pre-ground coffee compartment and
insert the spoon handle. Move the handle up and down until
the clogged ground coffee falls down (Fig. 26). Visit
www.saeco.com/care for detailed video instructions.
03 The brew group is dirty
or not well-greased.
Switch off the machine with the main switch. Rinse the brew
group with fresh water, let it air-dry and then lubricate it.
Consult chapter 'Cleaning the brew group' or visit
www.saeco.com/care for detailed video instructions. Then
switch the machine on again.
04 The brew group is not
positioned correctly.
Switch off the machine with the main switch. Remove the brew
group and reinsert it. Make sure that the brew group is in the
correct position before you insert it. Consult chapter 'Handling
the brew group or visit www.saeco.com/care for detailed
video instructions. Then switch the machine on again.
05 There is air in the water
circuit.
Restart the machine by switching it off and on again with the
main switch. If this works, dispense 2-3 cups of hot water.
Descale the machine if you have not done so for a longer
period of time.
The AquaClean filter
was not prepared
properly before
installation or it is
clogged.
Remove the AquaClean filter and try again to brew a coffee. If
this works, make sure that the AquaClean filter is prepared
properly before you place it back (see 'Preparing the
AquaClean filter for activation'). Put the AquaClean filter back
into the water tank. If this still does not work, the filter might be
clogged and needs to be replaced.
14 The machine is
overheated.
Switch the machine off and switch it back on again after 30
minutes.
Ordering accessories
To clean and descale the machine, only use the Philips maintenance products. These products can be
purchased from your local retailer, from the authorized service centers or online at
www.saeco.com/care. To find a full list of spare parts online, enter the model number of your
machine. You can find the model number on the inside of the service door.
Maintenance products and type numbers:
-Descaling solution CA6700
-AquaClean filter CA6903
-Brew group grease HD5061
-Coffee oil remover tablets CA6704
-Milk circuit cleaner CA6705
-Maintenance kit CA6707
15
English
Troubleshooting
This chapter summarizes the most common problems you could encounter with the machine. Support
videos and a complete list of frequently asked questions are available on www.saeco.com/care. If you
are unable to solve the problem, contact the Consumer Care Center in your country. For contact
details, see the warranty leaflet.
Problem Cause Solution
The drip tray fills up
quickly.
This is normal. The machine
uses water to rinse the internal
circuit and brew group. Some
water flows through the internal
system directly into the drip
tray.
Empty the drip tray every day or as
soon as the red 'drip tray full' indicator
pops up through the drip tray (Fig. 25).
Place a cup under the dispensing spout
to collect rinsing water.
The machine is in DEMO
mode.
You pressed the standby
button for more than 8
seconds.
Switch the machine off and then on
again with the main switch on the back
of the machine.
The 'coffee grounds
container full' icon
remains displayed.
You emptied the coffee
grounds container while the
machine was switched off.
Always empty the coffee grounds
container while the machine is switched
on. If you empty the coffee grounds
container when the machine is switched
off, the coffee cycle counter is not reset.
You placed back the coffee
grounds container too fast.
Do not place back the coffee grounds
container until the screen prompts you
to put it back.
The 'coffee grounds
container full' icon is
displayed even though
the container is not full.
The machine did not reset the
counter the last time you
emptied the coffee grounds
container.
Always wait approx. 5 seconds when
you place back the coffee grounds
container.In this way the coffee
grounds counter will be reset to zero.
Always empty the coffee grounds
container while the machine is switched
on. If you empty the coffee grounds
container when the machine is switched
off, the coffee grounds counter will not
be reset.
I cannot remove the
brew group.
The brew group is not in the
correct position.
Reset the machine in the following way:
place back the drip tray and the coffee
grounds container. Then close the
service door and switch the machine off
and back on again. Try again to remove
the brew group.
You have not removed the
coffee grounds container.
Remove the coffee grounds container
before you remove the brew group.
16 English
Problem Cause Solution
I cannot insert the brew
group.
The brew group is not in the
correct position.
Reset the machine in the following way:
place back the drip tray and the coffee
grounds container. Leave the brew
group out. Close the service door and
switch the machine on and off. Then put
the brew group in the correct position
and reinsert it into in the machine.
The coffee is watery. The brew group is dirty or
needs to be lubricated.
Clean and lubricate the brew group.
The grinder is set to a too
coarse setting.
Set the grinder to a finer (lower) setting.
The coffee settings have been
adjusted.
Select your coffee drink and adjust the
settings to a stronger coffee.
The machine is performing its
self-adjustment procedure
after a change in grinder
settings or bean types.
Brew a few cups of coffee.
The coffee is not hot
enough.
The cups you use are cold. Preheat the cups by rinsing them with
hot water.
The temperature is set too low.
Check the menu settings.
Set the temperature to 'high' in the
menu.
You added milk. Whether the milk you add is warm or
cold, it always decreases the
temperature of the coffee to some
extent.
Coffee does not come
out or coffee comes out
slowly.
The AquaClean filter was not
prepared properly for
installation or it is clogged.
Remove the AquaClean filter and try to
brew a coffee again. If this works, make
sure the AquaClean filter is prepared
properly before you place it back. Place
back the prepared filter. If this still does
not work, the filter might be clogged
and needs to be replaced.
The grinder is set to a too fine
setting.
Set the grinder to a coarser (higher)
setting.
The brew group is dirty. Clean the brew group.
The coffee dispensing spout is
dirty.
Clean the coffee dispensing spout and
its holes with a needle.
The machine circuit is blocked
by limescale.
Descale the machine.
The milk does not froth. The internal cappuccinatore is
dirty or not inserted correctly.
Clean the internal cappuccinatore and
make sure that you position and insert it
correctly (see 'Cleaning the internal
cappuccinatore under the tap').
17
English
Problem Cause Solution
The type of milk used is not
suitable for frothing.
Different types of milk result in different
amounts of froth and different froth
qualities. We have tested the following
milk types which proved to deliver a
good milk froth result: semi-skimmed or
full-fat cow's milk, soy milk and lactose-
free milk.
The milk is splashing. The milk you use is not cold
enough.
Make sure you use cold milk coming
directly from the fridge.
The flexible milk tube is not
connected properly.
Open the door of the coffee dispensing
spout (Fig. 8) and check if the flexible
milk tube is fully connected to the
cappuccinatore (Fig. 9). Note that the
cappuccinatore and milk tubes may be
hot. Let the cappuccinatore and the
tubes cool down before you touch
them.
The cappuccinatore and milk
tubes are not clean.
Remove and disassemble the internal
cappuccinatore (see 'Cleaning the
internal cappuccinatore under the tap').
Rinse all parts under the tap. For a
thorough cleaning, use the Philips milk
circuit cleaner and perform the DEEP
MILK CLEAN procedure via the cleaning
( ) menu. Note that if the parts have
been cleaned in the dishwasher, they
may have become clogged by food
particles or detergent residues. A visual
check that they are not obstructed is
also recommended.
We advise you to perform the
HygieSteam program every day: 1) Press
'Clean' on the control panel. 2) Select
'HygieSteam'. 3) Press the start button
to start the process, then confirm all
steps on the display.
The milk tubes are clogged. Always store the milk container without
the milk tubes in the refrigerator.
Leftover milk could accumulate within
the milk tubes and block the flow of
milk going through the tubes. Rinse the
milk tubes before storage.
The machine seems to
be leaking.
The machine uses water to
rinse the internal circuit and
brew group. Some water flows
through the internal system
directly into the drip tray.
Empty the drip tray every day or as
soon as the 'drip tray full' indicator pops
up through the drip tray cover (Fig. 25).
Place a cup under the dispensing spout
to collect rinsing water.
18 English
Problem Cause Solution
The drip tray is too full and has
overflowed which makes it look
like the machine is leaking.
Empty the drip tray every day or as
soon as the 'drip tray full' indicator pops
up through the drip tray cover (Fig. 25).
Place a cup under the dispensing spout
to collect rinsing water.
The machine is not placed on a
horizontal surface.
Place the machine on a horizontal
surface so that the 'drip tray full'
indicator works properly.
I cannot activate the
AquaClean filter and the
machine asks for
descaling.
The filter has not been replaced
in time after the AquaClean
filter icon flashed and the
capacity dropped to 0%.
Descale your machine first and then
install the AquaClean filter.
You did not install the
AquaClean filter during first
installation, but after having
brewed approx. 25 coffees
(based on 100ml/3oz cups). The
machine has to be completely
limescale-free before you
install the AquaClean filter.
First descale the machine and then
install a new AquaClean filter. After
descaling, the filter counter is reset to
0/8. Always confirm filter activation in
the machine menu. Also do this after
filter replacement.
The new water filter does
not fit.
You are trying to install another
filter than the AquaClean filter.
Only the AquaClean filter fits into the
machine.
The machine is making a
noise.
It is normal that your machine
makes noise during use.
If the machine starts to make a different
kind of noise, clean the brew group and
lubricate it (see 'Lubricating the brew
group').
The AquaClean filter was not
prepared properly and air is
now drawn into the machine.
Remove the AquaClean filter from the
water tank. Shake the filter for about 5
seconds. Immerse the filter upside
down in a jug with cold water for at
least 30 seconds. Wait until no more air
bubbles come out. Place the prepared
AquaClean filter back into the water
tank. Then dispense 2-3 cups of hot
water.
19
English
Water tank 1.7 litres, removable
Coffee bean hopper capacity 450 g
Coffee grounds container capacity 15 pucks
Milk container capacity (SM7580, SM7581.
SM7583 only)
600 ml
Adjustable spout height 75-148 mm
Nominal voltage - Power rating - Power supply See data plate on inside of service door
20 English
Technical specifications
The manufacturer reserves the right to improve the technical specifications of the product. All the
preset quantities are approximate.
Description Value
Size (w x h x d) 283 x 393 x 489 mm
Weight 10.8 - 12.2 kg
Power cord length 1200 mm
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87

Philips SM7480 Manuel utilisateur

Catégorie
Cafetières
Taper
Manuel utilisateur