Lenco LS-440 Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

Model: LS-430/LS-440
User manual - Turntable with 4 speakers built-in
and Bluetooth reception
Gebruikshandleiding - Platenspeler met 4 ingebouwde
luidsprekers en Bluetooth-ontvangst
Bedienungsanleitung - Plattenspieler mit 4 integrierten
Lautsprechern und Bluetooth-Empfang
Manuel de l’utilisateur – Tourne-disque équipé de
4 haut-parleurs intégrés et d’un récepteur Bluetooth
Manual del usuario - Tocadiscos con 4 altavoces integrados
y recepción por Bluetooth
Manuale dell'utente Giradischi con 4 altoparlanti
integrati e ricezione Bluetooth
1
Index
English .................................................................................................... 2
Nederlands ........................................................................................... 31
Deutsch ................................................................................................. 64
Français................................................................................................. 98
Español ............................................................................................... 134
Italiano ................................................................................................ 167
Version : 1.0
2
English
CAUTION:
Usage of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation exposure.
PRECAUTIONS BEFORE USE
KEEP THESE INSTRUCTIONS IN MIND:
1. Do not cover or block any ventilation openings. When placing the
device on a shelf, leave 5 cm (2”) free space around the whole
device.
2. Install in accordance with the supplied user manual.
3. Keep the device away from heat sources such as radiators,
heaters, stoves, candles and other heat-generating products or
naked flame. The device can only be used in moderate climates.
Extremely cold or warm environments should be avoided.
Working temperature between 0° and 35°C.
4. Avoid using the device near strong magnetic fields.
5. Electrostatic discharge can disturb normal usage of this device.
If so, simply reset and restart the device following the instruction
manual. During file transmission, please handle with care and
operate in a static-free environment.
6. Warning! Never insert an object into the product through the
vents or openings. High voltage flows through the product and
inserting an object can cause electric shock and/or short circuit
internal parts. For the same reason, do not spill water or liquid on
the product.
7. Do not use in wet or moist areas such as bathrooms, steamy
kitchens or near swimming pools.
8. The device shall not be exposed to dripping or splashing and make
sure that no objects filled with liquids, such as vases, are placed
on or near the apparatus.
3
9. Do not use this device when condensation may occur. When the
unit is used in a warm wet room with damp, water droplets or
condensation may occur inside the unit and the unit may not
function properly; let the unit stand in power OFF for 1 or 2 hours
before turning on the power: the unit should be dry before
getting any power.
10. Although this device is manufactured with the utmost care and
checked several times before leaving the factory, it is still possible
that problems may occur, as with all electrical appliances. If you
notice smoke, an excessive build-up of heat or any other
unexpected phenomena, you should disconnect the plug from the
main power socket immediately.
11. This device must operate on a power source as specified on the
specification label. If you are not sure of the type of power supply
used in your home, consult your dealer or local power company.
12. Keep away from animals. Some animals enjoy biting on power
cords.
13. To clean the device, use a soft dry cloth. Do not use solvents or
petrol based fluids.
To remove severe stains, you may use a damp cloth with dilute
detergent.
14. The supplier is not responsible for damage or lost data caused by
malfunction, misuse, modification of the device or battery
replacement.
15. Do not interrupt the connection when the device is formatting or
transferring files. Otherwise, data may be corrupted or lost.
16. If the unit has USB playback function, the USB memory stick
should be plugged into the unit directly. Don’t use an USB
extension cable because it can cause interference resulting in
failing of data.
17. The rating label has been marked on the bottom or back panel of
the device.
4
18. This device is not intended for use by people (including children)
with physical, sensory or mental disabilities, or a lack of
experience and knowledge, unless they’re under supervision or
have received instructions about the correct use of the device by
the person who is responsible for their safety.
19. This product is intended for non professional use only and not for
commercial or industrial use.
20. Make sure the unit is adjusted to a stable position. Damage
caused by using this product in an unstable position vibrations or
shocks or by failure to follow any other warning or precaution
contained within this user manual will not be covered by
warranty.
21. Never remove the casing of this device.
22. Never place this device on other electrical equipment.
23. Do not allow children access to plastic bags.
24. Only use attachments/accessories specified by the manufacturer.
25. Refer all servicing to qualified service personnel. Servicing is
required when the device has been damaged in any way, such as
the power supply cord or the plug, when liquid has been spilled or
objects have fallen into the device, when the device has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
26. Long exposure to loud sounds from personal music players may
lead to temporary or permanent hearing loss.
27. If the product is delivered with power cable or AC power adaptor:
If any trouble occur, disconnect the AC power cord and refer
servicing to qualified personnel.
Don’t step on or pinch the power adaptor. Be very careful,
particularly near the plugs and the cable’s exit point. Do not
place heavy items on the power adaptor, which may damage
it. Keep the entire device out of children’s reach! When
playing with the power cable, they can seriously injure
themselves.
5
Unplug this device during lightning storms or when unused
for a long period.
The socket outlet must be installed near the equipment and
must be easily accessible.
Do not overload ac outlets or extension cords. Overloading
can cause fire or electric shock.
Devices with class 1 construction should be connected to a
main socket outlet with a protective earthed connection.
Devices with class 2 construction do not require a earthed
connection.
Always hold the plug when pulling it out of the main supply
socket. Do not pull the power cord. This can cause a short
circuit.
Do not use a damaged power cord or plug or a loose outlet.
Doing so may result in fire or electric shock.
28. If the product contains or is delivered with a remote control
containing coin/cell batteries:
Warning:
“Do not ingest battery, Chemical Burn Hazard” or equivalent
working.
[The remote control supplied with] This product contains a
coin/button cell battery. If the battery is swallowed, it can
cause severe internal burns in just 2 hours and can lead to
death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop
using the product and keep it away from children.
If you think batteries might have been swallowed or placed
inside any part of the body, seek immediate medical
attention.
29. Caution about the use of Batteries:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
6
Battery cannot be subjected to high or low extreme
temperatures, low air pressure at high altitude during use,
storage or transportation.
Replacement of a battery with an incorrect type that can
result in an explosion or the leakage of flammable liquid or
gas.
Disposal of a battery into fire or a hot oven, or mechanically
crushing or cutting of a battery, that can result in an
explosion.
Leaving a battery in an extremely high temperature
surrounding environment that can result in an explosion or
that leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure that may
result in an explosion or the leakage of flammable liquid or
gas.
Attention should be drawn to the environmental aspects of
battery disposal.
INSTALLATION
Unpack all parts and remove protective material.
Do not connect the unit to the mains before checking the mains
voltage and before all other connections have been made.
* Those instruction are related only to products using power cable or
AC power adaptor.
7
Product Description
1. DC INPUT Jack
2. Phono & Line Out Switch
3. AUX IN Jack
4. Phono & Aux Out Jacks
5. Lid Hinge
6. Counterweight
7. Tracking Force Dial
8. Tonearm Clip
9. Tonearm Lift Lever
10. Tonearm
11. Tone Control
12. Pitch Control
13. Volume Control
14. ON/OFF/Function Button
15. 33 1/3 RPM Speed Button
16. START/Stop Button
17. 45RPM Speed Button
18. Headphone Jack
19. Indicator
20. Stylus Cartridge
21. Turntable Platter
22. Turntable Spindle
8
Included Items
Before installing the turntable, check the package contents to ensure
all parts below are included and free of visible damage. Please retain
the original packaging materials for exchange or return purposes.
1. Turntable Unit
2. Power Adapter
3. Turntable Lid
4. Slip Mat
5. Platter with Belt
6. Counterweight
7. Cartridge Alignment
Protractor
8. 45 RPM Adapter
9. Instruction Manual
Installing the turntable
. Mount the turntable on a level surface.
. To avoid the effects of vibrations and acoustic pressure, do not mount
the turntable next to items such as speakers.
. The turntable may pick up radio static if placed next to a radio.
Therefore, try to keep the turntable away from radios.
. If the turntable is near equipment (cell phone, etc.) that emits
strong radio waves, noise may occur.
9
Installing the Lid
Insert the hinge pockets of the lid onto the hinges of the turntable.
10
Turntable Platter and Belt Setup
1. Turn the platter over and check the belt position.
Make sure that the drive
belt is looped in the middle
of the circle. The drive belt
located too high or too low
in this circle may cause the
drive belt to fall off or speed
to be unstable.
2. Set the platter on the spindle.
Make sure the platter is fully seated on the spindle.
3. Place the belt on the motor pulley.
Align one of the platter openings with the motor pulley, and while
pulling both ends of the red ribbon that comes attached to the belt,
place the belt on the motor pulley, as per the diagram. When doing
this, be careful not to twist the belt.
11
4. Remove the red ribbon from the belt.
Rotating the Platter
Cartridge Tracking Force Adjustment
The supplied Counterweight is
suitable for cartridges weighing
between 3.0-6.0g.
12
1. Gently push and turn the counterweight
onto the rear of the tonearm (with the
dial facing toward the front of the
turntable).
2. Pull the protector straight forward to
remove it.
NOTE: Applying a downward force may
cause the stylus to come off the body.
Only low volume is output if the stylus has
come off, or is about to come off, so refer
to "Replacing the stylus" to reattach the
stylus correctly.
3. Remove the tie-wrap and unlock the tonearm.
4. Lower the tonearm lift lever and position the cartridge in the space
between the tonearm rest and platter.
5. Carefully rotate the counterweight until the tonearm achieves a
neutral balance. The tonearm should return to this balanced
position if it is moved up or down. This adjustment must be done
carefully.
6. Once the tonearm is correctly balanced, return the tonearm to its
13
rest. Without moving the position of the counterweight, gently
rotate the tracking force dial until the zero is in line with black
center line on the rear of the tonearm. Check to make sure the
tonearm is still neutrally balanced.
7. Finally, rotate the counterweight and tracking force dial together
counterclockwise (as seen from the front) to adjust the tracking
force according to the cartridge manufacturer's recommendations.
Note: Each mark on the scale represents 0.1g.The recommended
tracking force for the factory-installed cartridge is 3.5g±0.5g. Carefully
rotate the tracking force dial. When "3.5" is centered over the black
line on the top of the tonearm please stop.
Connection to External Speaker with RCA Audio Cable
This turntable includes 4 built-in speakers and a built-in phono amplifier.
If you wish to use your own amplifier or speakers, please follow the
instructions below:
14
NOTE: In order to achieve the best sound, it is advised to set the
turntable volume to a minimal level. Then the turntable's audio will be
played back through your own amplifier, speakers, etc.
1. Setting pre-amplifier selector switch
This product has a built-in phono amplifier function. You can use
the product even if you do not have a phono amplifier or
connectable equipment with a built-in phono amplifier.
Use the pre-amplifier selector switch to set the output, as shown
below.
Connectable equipment being
used
Position of pre-amplifier
selector switch
Where to connect RCA audio
cable
Device with phono input
PHONO
Phono input jack and ground
(earth) terminal of
connectable equipment
Device without phono input
LINE
AUX or line input jack of
connectable equipment
NOTE: The RCA Jacks are not designed to be connected directly to the
passive/unpowered speakers on LINE mode. If connected to the passive
speakers, there will be no sound.
15
2. Connecting the device
Align the settings for the pre-amplifier selector switch and
connect the RCA audio cable to an input jack that is
compatible with the connectable equipment you are using
(amplifier, active speakers, etc.).
The RCA audio cable's red jack is for the right (R) channel, and
the white jack is for the left (L) channel.
16
Main Power Connection
1. Insert the DC plug of the AC adapter cord into the DC INPUT Jack at
the back of the turntable.
2. Plug the AC adapter into a normal power outlet.
NOTE: Do not plug the AC power adapter into a power outlet before all
turntable assembly is completed. Before turning on turntable power,
recheck all connections to make sure they are correct and secure.
Always turn off the turntable before connecting or disconnecting from
power.
Power Management Function
The turntable will automatically power off after 20 minutes of
inactivity.
The indicator light will turn off.
To resume operation, press the ON/OFF button again.
Playing a Record
1. Before playing a record
1.1. Pull the protector straight forward to remove it.
NOTE: Applying a downward force may
cause the stylus to come off the body.
Only low volume is output if the stylus
has come off, or is about to come off, so
refer to "Replacing the stylus" to reattach
the stylus correctly.
1.2. Place the record on the felt mat so that the center hole aligns with
the spindle.
17
2. Turntable Operation
Sufficiently lower the volume of the amplifier and speakers first.
2.1. Connect the included power adapter to the turntable, press the
mode button. The turntable will turn on. The indicator will light in
red.
2.2. Remove the stylus protector from the stylus.
2.3. Place the record on the slip mat.
2.4. Press the Speed Selector button to switch between 33 and 45 RPM
speeds according to the type of record.
2.5. Press the START/Stop button once and the platter will play or
pause.
2.6. Unlock the tonearm clip and set the tonearm lift lever to the up
position.
2.7. Position the tonearm over the desired location (groove) on the
record.
2.8. Carefully lower the tonearm on the record by setting the tonearm
lift lever to the down position.
2.9. Turn up the volume of the turntable as needed.
2.10. When you are finished playing the record, raise the tonearm,
return it to rest on the arm clip and long press the mode button to
turn off the turntable.
3. Pitch Control
3.1. The turntable speed can be increased or decreased by
approximately 10% by rotating the Pitch Control knob.
3.2. To increase the speed, turn the Pitch Control knob clockwise.
3.3. To decrease the speed, turn the Pitch Control knob counter-
18
clockwise.
4. Tone Control
4.1. The tone of this turntable could be adjusted by rotating the Tone
Control knob.
4.2. To be a brighter sound, turn the Tone Control knob clockwise.
4.3. To be a deeper sound, turn the Tone Control knob counter-
clockwise.
NOTE:
1. If the silent pause time between each track is longer than
3 minute, the platter will stop spinning automatically to avoid
damaging the record. The indicator light will be red. To resume
operation, press the START button.
2. If the felt mat gets dirty, it can easily scratch the record, so remove
the felt mat periodically and wipe off any dust.
3. To prevent the record from scratches and warping, remove it after
use.
4. Do not use a disk stabilizer.
AUX-IN Operation
This turntable includes an auxiliary audio signal input jack for
connecting external audio devices like MP3 players, CD players, and
older, non-dockable iPods so you can listen to your external source
through the turntable's speakers.
1. Use an audio cable (not included) with one 3.5 mm stereo
connection on each end of the cable.
2. Plug one end into the AUX-IN jack on the turntable and the other
end to the Line Out jack of the audio device.
3. Power on the turntable and audio device. The indicator light of
turntable is red.
4. Press the MODE button again, the indicator light of turntable
19
turns green. It's AUX-IN mode.
5. The volume level can be controlled through the turntable.
Operate all the functions on the auxiliary device as usual.
NOTE:
1. Make sure the tone arm is securely locked to avoid any damage.
2. When you are done, don't forget to turn off the power on the
turntable and your external device.
Bluetooth Operation
1. Connect the included power adapter to the turntable and press
the mode button, the indicator will light in red.
2. Press the mode button twice to Bluetooth mode. The indicator
light turns blue and flash quickly. You will hear an activation sound
from the turntable.
3. Turn on the Bluetooth feature of your media device and search for
and select "Lenco LS-430/Lenco LS-440 "to pair the media device
and turntable.
4. Once your media device is successfully paired with the turntable,
the turntable will play a short confirmation sound.
5. Play and stream music from your media device to the turntable.
The indicator light will become solid.
Note: Bluetooth version: 5.0
“This product has a bluetooth reception function, you can not
transmit any bluetooth sound with it: this means that you can
receive wirelessly a bluetooth sound signal from an external
source like a smartphone.”
Care
Turntable Body
When the turntable body is dirty or dusty, first disconnect the AC
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200

Lenco LS-440 Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à