Bercomac 700512-5-24H-EPA 700512-5-22.5K-EPA 700512-5-25K-EPA Manuel utilisateur

1

BERCO

VANTAGE 66’’ & 72’’ Snowblower

For

OFF ROAD UTILITY VEHICLE

CAUTION:

READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE

OPERATING YOUR EQUIPMENT

R-10082015

* ASSEMBLY * REPAIR PARTS

* OPERATION * MAINTENANCE

*108056*

OWNER’S MANUAL

Model Number

Original Version

700512-5 66’’ Snowblower

700513-5 72’’ Snowblower

108056-EN

700512-5 EPA

700513-5 EPA

2

LIMITED WARRANTY

Bercomac Limitée

92, Fortin North, Adstock, Quebec, Canada, G0N 1S0

Conditions and Products Covered:

BERCOMAC guarantees any part of the product or accessory

manufactured by BERCOMAC and found in the reasonable

judgment of BERCOMAC to be defective in material and or

workmanship will be repaired or replaced by an authorized

dealer without charge up to our maximum labor rates and pre-

established times. For replacement parts only standard ground

freight services are covered. This warranty extends to the

original retail purchaser only and is not transferable to any

subsequent purchasers. This warranty applies to the products

bought and used in North America.

Warranty Period

(from date of the original retail purchase):

 Residential or semi-commercial use: 1 year

 Commercial, professional or rental use: 90 days

Exceptions Noted Below; the following items are guaranteed

by the original manufacturer and have their own warranty,

conditions and limited time:

 Tire Chains: 90 days

 Engines: Will vary as per the manufacturer

Please refer to the engine manufacturer’s warranty

statement included with the unit. BERCOMAC is not

authorized to handle warranty adjustments on engines.

Items and Conditions NOT Covered:

This warranty does not cover the following:

 Pick-up or delivery charges or in-home services fees.

 Any damage or deterioration of the unit, parts and or finish

of these due to normal use, wear and tear, or exposure.

 Cost of regular use or maintenance service or parts, such as

gas, oil, lubricants, tune-up parts, and adjustments.

 Any part or accessory which has been altered, modified,

misused, neglected, accidentally damaged or not properly

installed, maintained, stored or repaired not in accordance

with the instructions in the owner’s manual.

 Repair due to normal wear and or any wear items include

but are not limited to items such as shear pins, bolts, belts,

winch cables, cutting edge, skid shoes etc.

 Expedited freight fee services for replacement parts.

 Shear bolts and shear pins are to be considered as a

preventive measure not as an assured protection, any

damages resulting from the lack of shear bolts breakage are

not covered.

 Damages due to product being installed on vehicle other

than stipulated in the owner’s manual.

NOTE: All warranty work must be performed by an authorized

dealer using original (manufacturer) replacement parts.

Owner’s Responsibilities:

Any defective equipment or part must be returned to an

authorized dealer within the warranty period for repairs. In the

event that defective merchandise must be returned to

manufacturer for repairs, the dealer must first obtain a written

authorization from either KIMPEX or BERCOMAC, freight fees

are prepaid prior to the shipment. This warranty extends only

to equipment operated under normal conditions. To validate a

warranty claim, it is the user’s responsibility to maintain and

service the unit as specified in the owner’s manual or to have

the unit serviced at their dealer at their expense.

General Conditions:

The sole liability of BERCOMAC with respect to this warranty

shall be strictly and exclusively repair and replacement as

mentioned herein. BERCOMAC shall not have any liability for

any other costs, loss or damage, including but not limited to,

any incidental or consequential loss or damage.

Taking advantage of the warranty does not in any way extend

the length or renewal of the warranty.

In particular, without being limited to, BERCOMAC shall have

no liability or responsibility for:

 Travel time, overtime, after hours time or other

extraordinary repair charges or relating to repairs and or

replacements outside of normal business hours.

 Rental of like or similar replacement equipment during the

period of any, repair or replacement work.

 Any communicating or travel charges.

 Loss or damage to person or property other than that

covered by the terms of this warranty.

 Any claims for lost revenue, lost profit or any similar costs

as a result of damage or repair.

 Attorney’s fees.

BERCOMAC’s responsibility in respect to claims is limited to

making the required repairs or replacement without charge up

to our maximum labor rates and pre-established times and no

claim of breach of warranty shall be cause for cancellation or

rescission of the contract of sale of any product or accessory.

In no event shall recovery of any kind be greater than the

amount of the purchase price of the product sold.

This warranty gives you specific legal rights. You may also

have other rights, which vary from state to state.

NOTE: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify

any product previously manufactured.

Instructions for Obtaining Warranty Services:

Contact dealer where equipment was purchased or any other authorized service dealer to arrange service at their dealership. Requests

for warranty claims must be carried out through the same distribution network used to purchase the product. Don't forget to bring your

proof of purchase (sales receipt) to the dealer.

1

TABLE OF CONTENTS

INTRODUCTION ...................................................................................................................................................... 2

SAFETY PRECAUTIONS ........................................................................................................................................ 3

SAFETY DECALS .................................................................................................................................................... 5

ASSEMBLY

Tools Required ........................................................................................................................................... 6

Snowblower Preparation ............................................................................................................................ 7

Vehicle Preparation ..................................................................................................................................... 8

Preparing the Subframe ............................................................................................................................. 9

Installing on the Vehicle ............................................................................................................................. 11

Control Box Installation .............................................................................................................................. 13

Installing the Spring .................................................................................................................................... 15

OPERATION

Snowblower Operation ................................................................................................................................ 16

Electrical Controls ........................................................................................................................................ 16

Lifting and Lowering the Snowblower ....................................................................................................... 16

Burnishing Procedure ................................................................................................................................... 16

Snowblowing Technique ............................................................................................................................ 17

Skid Shoe Adjustment ............................................................................................................................... 17

MAINTENANCE

Engine Maintenance .................................................................................................................................. 18

Snowblower Maintenance ......................................................................................................................... 18

Pressure of the tires on the subframe ......................................................................................................... 18

Clearing a Clogged Discharge Chute ....................................................................................................... 18

Cutting Edge Maintenance ........................................................................................................................ 18

Lubrication ................................................................................................................................................... 18

Auger and Fan Shear Bolt Replacement .................................................................................................. 19

Belt Replacement ....................................................................................................................................... 20

Replacing the Augers, Fan and / or Gear Box ......................................................................................... 21

MAINTENANCE & DISMOUNTING ....................................................................................................................... 22

TROUBLESHOOTING ............................................................................................................................................. 23

PARTS BREAKDOWN AND PARTS LIST

Vantage Snowblower 66’’ ............................................................................................................................ 25

Vantage Snowblower 72’’ .......................................................................................................................... 35

Subframe ..................................................................................................................................................... 45

Honda Engine 24hp ................................................................................................................................... 47

Kohler Engine 22.5hp ................................................................................................................................. 50

Kohler Engine 25hp .................................................................................................................................... 52

Exploded view parts ..................................................................................................................................... 54

TORQUE SPECIFICATION TABLE ....................................................................................................................... 56

OPTIONS & ACCESSORIES ……. ......................................................................................................................... 57

2

INTRODUCTION

TO THE PURCHASER

This new accessory was carefully designed to give years of dependable service. This manual has been provided to

assist in the safe operation and servicing of your attachment.

NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but

are intended for reference only and are based on the latest product information available at the time of publication.

Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to

use. Carefully read, understand and follow these recommendations and insist that they be followed by those who will

use this attachment.

THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS

MANUAL THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH.

DANGER, WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF

HAZARD. HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.

DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions

are not followed.

WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are

not followed.

CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are

not followed.

Record your attachment serial number and purchase date in the section reserved below (there is no serial number on

the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement

parts. Use only genuine parts when replacements are required.

If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer

for warranty service.

This manual should be kept for future reference.

Please check if you have received all the parts for your kit with the list of the

bag and the list of the box.

SERIAL NUMBER : ___________________________

(IF APPLICABLE)

MODEL NUMBER: ___________________________

PURCHASE DATE : ___________________________

3

SAFETY PRECAUTIONS

Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle

and accessory. This accessory is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury. All operators, no matter how experienced they may be,

should read this and other manuals related to the vehicle and accessory before operating. It is the owner's legal

obligation to instruct all operators in safe operation of the accessory.

GLOSSARY:

In this manual, right and left sides are determined by

sitting on the seat of the vehicle facing forward.

In this manual, "accessories" means attachments

(snowblower, rotary broom, blade etc.) that you install

on the vehicle (lawn tractors, A.T.V. s etc).

TRAINING:

This symbol, "Safety Alert Symbol", is used

throughout this manual and on the

accessory’s safety labels to warn of the

possibility of serious injury. Please take

special care in reading and understanding

the safety precautions before operating the

vehicle and accessory.

1. Read this owner's manual carefully. Be thoroughly

familiar with the controls and proper use of the

vehicle and accessory. Know how to stop the unit

and disengage the controls quickly.

2. Never allow children to operate the vehicle nor the

accessory. Never allow adults to operate the vehicle

nor the accessory without proper instructions.

3. No one should operate the vehicle nor the

accessory while intoxicated or while taking

medication that impairs the senses or reactions.

4. Keep the area of operation clear of all people,

particularly small children and pets.

5. Never start or operate the accessories except from

the operator’s station on the power unit except if

this is impossible.

PREPARATION:

1. Thoroughly inspect the area where the accessory

is to be used and remove door mats, all foreign

objects and the like.

2. For motorized accessories, disengage all clutches

and shift into neutral before starting engine.

3. Do not operate the accessory without wearing

adequate winter outer garments. Avoid loose fitting

clothing that can get caught in moving parts. Wear

footwear that will improve footing on slippery

surfaces.

4. Handle fuel with care, it is highly flammable.

a) Use approved fuel container.

b) Never add fuel to a running engine or hot engine.

c) Fill fuel tank outdoors with extreme care. Never fill

fuel tank indoors.

d) Never fill containers inside a vehicle, or on a

truck or a trailer bed with a plastic liner. Always

place containers on the ground, away from your

vehicle, before filling.

e) When practical, remove gas-powered

equipment from the truck or trailer and refuel it

on the ground. If this is not possible, then refuel

such equipment on a trailer with a portable

container, rather than from a gasoline

dispenser nozzle.

f) Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times, until

refueling is complete. Do not use a nozzle lock-

open device.

g) Replace fuel cap securely and wipe up spilled

fuel.

h) If fuel is spilled on clothing, change clothing

immediately.

5. Never attempt to make any adjustments while the

engine (motor) is running (except when specifically

recommended by manufacturer).

6. Let the vehicle and accessory adjust to outdoor

temperatures before using.

7. Never use an accessory without proper guards,

plates, or other safety protective devices in place

8. Always make sure to wear the appropriate safety

equipment required (glasses, muffs, mask…) for

each type of product. See operation section.

9. Always make sure of having safe traction on the

vehicle by using the recommended accessories

(chains, A.T.V. tracks, counterweights…). See

operation section.

10. Always make sure all components are correctly

installed. (driveline securely attached and locked at

both ends, belts properly installed…)

11. If applicable, always handle the winch cable with

thick leather gloves.

12. Never modify the accessory or any part without

the written consent from the manufacturer.

4

OPERATION:

1. Do not put hands or feet near, under or inside rotating

parts.

2. Exercise extreme caution when operating on or

crossing gravel drives, walks or roads. Stay alert for

hidden hazards or traffic. Do not carry passengers.

3. After striking a foreign object, stop the engine (motor),

disconnect the wire from the spark plug(s) and keep

wire away to prevent accidental starting. Thoroughly

inspect the accessory for any damage and repair

damage before restarting and using the accessory.

4. If the unit should start to vibrate abnormally, stop the

engine (motor) and check immediately for the

cause. Vibration is generally a warning of trouble.

5. Take all possible precautions when leaving the

vehicle unattended. Disengage the power take-off,

lower the attachment, place the transmission into

neutral, set the parking brake, stop the engine and

remove the ignition key.

6. Do not run the engine indoors, except when starting

the engine and for transporting in or out of the

building. Do not operate or let motor run in a storage

area without ventilation because gas contains

carbon monoxide which is odorless, colorless and

can cause death.

7. Never use the accessories across the face of

slopes, go from top to bottom. Exercise extreme

caution when using equipment on slopes. Do not

attempt to clear a steep slope.

8. Never tolerate bystanders in the working zone.

Never use an accessory in the direction of

bystanders, it might throw gravel or debris that can

hurt people or damage property.

9. Never operate the accessory at high transport

speeds on slippery surfaces. Use care when

backing up.

10. Do not carry passengers.

11. Disengage power to the accessory when it is

transported or not in use.

12. Never operate the accessory without good visibility

or light.

13. Keep the accessory away from heat sources or

flames.

14. If applicable, never handle the winch cable or hook

while in tension.

MAINTENANCE AND STORAGE

1. When cleaning, repairing or inspecting the vehicle

and accessory: stop the engine, set brake, remove

ignition key, and wait that all moving parts have

stopped. For gasoline engine, disconnect wire from

the spark plug(s) and keep wire away to prevent

accidental starting.

2. Check all the bolts and components at frequent

intervals to make sure that they are properly

tightened.

3. Never store a motorized accessory with fuel in the

fuel tank inside a building where ignition sources are

present such as hot water and space heaters,

clothes dryers, and the like. Allow the engine to cool

before storing in any enclosure.

4. Always refer to the owner’s manual when you store

the accessory and vehicle for a prolonged or an

unspecified length of time.

5. Maintain or replace safety and instruction labels, as

necessary.

6 For winter accessories, (if applicable), let the engine

run for a few minutes after clearing snow in order to

prevent the rotary parts from freezing.

7. Inspect the vehicle’s and accessory’s air filter (if

applicable) every day. Clean it or replace it as

necessary. Change the oil more often when working

in dusty conditions. See the vehicle’s and

accessory's owner’s manual.

TRANSPORT

1. Review Transport Safety instructions in vehicle

manual before moving.

2. Check with local authorities regarding transport on

public roads. Obey all applicable laws and

regulations.

3. Make sure all lights and reflectors that are required

by the local highway and transport authorities

(exemple : SMV (Slow Moving Vehicle)) are in

place, are clean, and can be seen clearly by all

overtaking and oncoming traffic.

4. Never have the equipment in operation during

transport.

5. Always travel at a safe speed.

SAFETY PRECAUTIONS

5

REPLACE IF DECALS ARE DAMAGED

SEE PARTS BREAKDOWN FOR DECAL LOCATION

SAFETY DECALS

Symbol Description

Decal #105126

To avoid serious injury:

Keep hands, feet & clothing away from rotating auger while engine is

running.

Decal #105127

To avoid serious injury:

Keep hands out of this discharge chute while engine is running.

Decal #105128

To avoid serious injury:

Keep hands, feet & clothing away.

Do not attempt to install or remove drive belt without reading owner’s

manual.

Decal #105130

Before installing or using:

Locate, read and make sure to understand all of the owner’s manual.

Decal #105131

Refer to owner’s manual about wearing safety glasses, ear muffs and

mask.

Refer to owner’s manual for use of counter weights, cat tracks and tire

chains.

1-Do not drive faster than 3 KM/H when the snowblower is in operation.

2-Do not drive faster than 10 KM/H when the snowblower is in the raised

position.

3-The head of the snowblower weighs 96 kg. (without engine).

4-The engine wattage. (See specification of the engine installed).

5-The sound pressure level (See specification of the engine installed).

6

ASSEMBLY

ASSEMBLY INSTRUCTIONS

IMPORTANT: UNLESS OTHERWISE SPECIFIED TORQUE ALL BOLTS ACCORDING TO TORQUE

SPECIFICATION TABLE (SEE TABLE OF CONTENTS) WHEN STATED: TIGHTEN FIRMLY. REFER TO

PARTS BREAKDOWN SECTION FOR PART IDENTIFICATION.

IMPORTANT: THE VEHICLE MUST BE EQUIPPED WITH A 2’’ TOW HITCH BALL IN ORDER TO INSTALL

THE VANTAGE SNOWBLOWER.

TOOLS REQUIRED

1 Ratchet

3 Wrenches 7/16’’, 1/2’’, 9/16’’

3 Sockets 7/16’’, 1/2’’, 9/16’’

1 Hexagonal wrench 5/32’’

1 Wrench (for the nuts on the vehicle's battery

post)

Figure 1 - Overall view of the Vantage snowblower

CONVERSION TABLE

1’’ (po, in) 25.4 mm

1’ (pi, ft) 0.3 m

1 psi (lb/in2) 6.89 kPa

1 lb 0.45 kg

1 lbf 4.4 N

1 m/h (mi/h) 1.61 km

1 hp (cv) 0.75 kW

GLOSSARY

Quad = V.T.T., A.T.V.

Véhicule tout terrain V.T.T.

All terrain vehicle A.T.V.

Utility Vehicle U.V

Véhicule Utilitaire V.U.

P.T.O. = P.D.F

Power take-off (P.T.O)

Prise de force (P.D.F)

7

ASSEMBLY

SNOWBLOWER PREPARATION:

Refer to parts breakdown section for parts

identification.

Install the nylon rotation ring

Install the chute

Install the rotation ring

Install the nylon rotation ring (item 1) over the

opening (item 2) as shown and align the notches.

Install the rotation ring (item 1) over the opening as

shown.

NOTE: Place grooves of the rotation ring onto the

grooves of the rotation motor and place notch (A and

B) as shown.

Install the chute (item 1) over the nylon rotation ring

(item 2). Turn the chute to make sure it turns freely.

Place the chute at a 45° angle as shown.

Insert the hex bolts 1/4’’ x 1’’ (item 3) under the

rotation ring (item 6) in each hole as shown. Insert the

spacers (item 4) on the hex bolts between the rotation

ring and the chute.

Secure in place with the 1/4’’ nylon insert lock nuts

(item 5).

8

Install the retaining plate

ASSEMBLY

Insert the 1/4’’ x 1/2’’ hex bolts (item 1) in the holes

as shown.

Install the retaining plate (item 2) under the chute as

shown.

Secure in place with the 1/4’’ nylon insert lock nuts as

shown.

Choose one of the three following options as a

means of fastening the subframe.

OPTION A:

Install the lift strap (item 1) by making a loop around

the front suspension arm of the vehicle.

Tighten the loop firmly.

OPTION B:

Remove the nut and bolt from the vehicle’s front

suspension arm. Secure the bracket (item 3) with a

bolt, flat washer and nut (item 2).

Do not tighten the nut too firmly.

OPTION C:

Remove the nut and bolt from the vehicle’s front

suspension arm. Secure the bracket (item 4) with a

bolt, flat washer and nut (item 2).

Do not tighten the nut too firmly.

NOTE: Repeat the operation on the other side of

vehicle.

VEHICLE PREPARATION:

Install the lift strap or the brackets.

9

ASSEMBLY

Install the wheel support to the subframe

PREPARING THE SUBFRAME

Assemble the wheel support (item 1) on the subframe

(item 2) with four hex bolts 3/8" x 1" (item 3) and four

flange nuts 3/8" (item 4).

NOTE: The set of holes used to assemble the wheel

support to the subframe depends on the height of the

vehicle. Once installed the subframe must be parallel

with the ground.

Install the assembled turnbuckles

Install the assembled turnbuckles (item 1) and chain

(item 2) on the bracket (item 6) that is welded on the

subframe (as shown).

Secure the chains with two hex bolts 5/16" x 1" (item

3), two flat washers 3/8" (item 4) and two nylon insert

lock nuts 5/16" (item 5).

Slightly tighten the nuts to allow the parts to move

freely.

Install the snowblower (item 1) to the wheel support

(item 2). Slide the pin (item 3) through the assembly

to hold everything together. Hold the pin in place with

the hair pin 4mm (item 4) as shown.

NOTE: Make sure the pin is in the locked position.

Install snowblower

10

ASSEMBLY

There are seven different positions on the adjustment

tube (item 1) (the adjustment tube can be inverted) to

adjust the length of the subframe.

To choose the right adjustment, insert the adjustment

tube into the subframe (item 2) and insert the rear

bracket (item 3) on the adjustment tube. Slide the

hitch support (item 4) on the rear bracket. Do not

secure.

Assembling the subframe

Drive the vehicle over the subframe, make sure the

caster wheels do not touch the front wheels of the

vehicle.

Identify the right length of the subframe (item 1) and

secure in place with two long pins (item 2), a short pin

(item 3) and three hair pins 3mm (item 4).

Securing the subframe

Among the three following configurations, choose

the height of the hitch support. There must be a

maximum of ground clearance.

(Configuration A) does not have the hitch support

plates (item 1).

If applicable, assemble the hitch support plates on

the hitch support (item 2) with four hex bolts 3/8" x

3/4" (item 3) and four nylon insert lock nuts 3/8".

Secure the hitch (item 4) on the two hitch support

plates or on the hitch support with a hex bolt 3/8" x

3" (item 5) and one nylon insert lock nut 3/8".

Tighten firmly

Adjusting the hitch support

11

ASSEMBLY

INSTALLING ON THE VEHICLE

Place the hitch (item 1) on the tow hitch ball and

secure in place with a pin (item 2) and a hair pin (item

3).

IMPORTANT: Make sure the vehicle never comes

into contact with the subframe even when the

vehicle’s suspensions are compressed to the

maximum.

NOTE: It is possible to turn the hitch support to

facilitate driving the vehicle over the subframe.

Installing the subframe on the tow hitch ball

Adjusting the hitch coupler

NOTE: Correct adjustment will allow the handle to be

released with moderate pressure applied to the

handle.

To open, pull up on hitch coupler handle and rotate

forward.

Place hitch coupler on ball.

When ball is completely nested in ball socket, rotate

hitch coupler handle backward until handle is in

locked position.

Always check tightness before using the tow hitch.

Be sure hitch coupler handle is in locked position.

Operation instructions for hitch coupler:

WARNING

TO PREVENT INJURIES:

Always check that ball is completely inserted into

hitch coupler socket and that under jaw is securely

closed around the bottom of ball.

Always check that hitch coupler handle is properly

locked before its use.

Always examine hitch coupler and ball for damage

before using, replace if damaged.

Lock the handle (item 1) into position over the ball in

the hitch coupler. Tighten the lock nut (item 2) against

the spring so that the hitch coupler is not loose on the

ball.

12

Install the turnbuckles

For vehicles with a winch that is higher than

20’’ (510mm) from the ground, follow these

instructions:

Install pulley (item 1) in the top hole of the lever with a

1/2’’ x 1 3/4’’ hex bolt (item 2) and secure in place

with the nylon insert lock nut. Tighten firmly.

Insert the winch hook (item 3) in the rod (item 4).

Secure the winch cable by inserting the lynch pin

(item 5) in the small hole (item 6).

For vehicles with a winch that is lower than

20’’ (510mm) from the ground, follow these

instructions:

Install pulley (item 1) in the bottom hole (item 7) of the

lever with a 1/2’’ x 1 3/4’’ hex bolt (item 2) and secure

in place with the nylon insert lock nut. Tighten firmly.

Insert the winch hook (item 3) in the rod (item 4).

Secure the winch cable by inserting the lynch pin

(item 5) in the small hole (item 6).

TIP: Thread the winch hook in front of the hitch as

shown and then thread the cable over the pulley. Install the winch hook

Hook the turnbuckles (item 1) in the brackets or the lift

straps. Tighten the turnbuckles firmly.

IMPORTANT: After adjusting the turnbuckles, tighten

firmly the nuts that secure the brackets on the

vehicle’s suspension arms. Make sure to lock the nuts

with the original locks. Furthermore, tighten firmly the

turnbuckle assembly nuts that secure them to the

subframe.

ASSEMBLY

Verification of turnbuckles installation

1 2

3

16’’ max.

40cm max.

NOTE: In the event where the vehicle is equipped

with a prominent front bumper or tracks, the

assembled turnbuckles (item 3) will become too

angled. Relocate the assembled turnbuckles from

plate 1 towards plate 2.

IMPORTANT: To avoid any damages to the

subframe or vehicle, plate #2 must be placed in front

of the wheels’ center if the assembled turnbuckles are

relocated.

13

ASSEMBLY

CONTROL BOX INSTALLATION:

Install the control box

Connect wire assembly (104017) to the positive post

on the vehicle’s battery. Connect the black wire on

the vehicle’s frame.

IMPORTANT: The control box is equipped with a red

emergency kill switch in case you need to stop the

engine quickly.

NOTE: The emergency kill switch must be pulled out

to start the engine’s accessory.

Connect the wire on the battery

Disconnect the wires that are connected to the

control box (item 3).

Install the box support (item 1) in an appropriate

place . Drill holes if necessary. Secure the box

support with the two 1/4’’ x 1/2’’ hex bolts and flange

nuts.

Tighten firmly.

Install the control box on the box support.

Thread the wires that unites the accessory under the

hood to the front of the vehicle.

NOTE: Excess of wire is available, if needed, under

the engine.

Wire assembly

Connect wiring of snowblower.

14

Connect the wire connector on the motor of the chute

deflector (item 1)

Make sure the connectors are well connected

together and tie the wire that is connected to the

motor of the deflector with a nylon tie wrap (item 2) as

shown. Cut off any excess of the tie wrap.

Secure the wires as shown

ASSEMBLY

WARNING:

Be sure to leave enough wire length to be able to turn

the chute freely and that no wiring comes into contact

with the motor’s muffler.

IMPORTANT: Take time to familiarize yourself with

the location of the switches and with their functions.

DANGER: Always make sure that all the guards are

installed before starting the snowblower engine.

DANGER: It is the responsibility of the person who

installs the accessory to make sure the engaging

system works well and that the snowblower

disengages effectively at all times. It is imperative to

make the necessary adjustments if applicable.

Identification of the switches:

1. Emergency kill switch. (Pull out to start).

2. Joystick to move the chute and the deflector.

3. Switch to activate the electric clutch.

4. Switch for optional light kit.

Identify the controls.

DANGER: For the next manipulations, make sure to

clear the area in front of the snowblower and the

outflow of the chute of all people or objects.

1. Manipulate the four position switch (item 2) and

make sure the chute deflector and rotation works

well.

2. Activate the electromagnetic clutch switch (item 3).

Make sure the clutch engages and disengages.

3. Engage the electromagnetic clutch. Try to start he

snowblower engine. Make sure the engine does

not start.

4. Disengage the electromagnetic clutch. Try to start

the snowblower engine. Make sure the engine

starts.

5. While the engine is running, activate the kill switch

(item 1). Make sure the engine stops. Deactivate

the kill switch by turning it clockwise.

6. If the snowblower is equipped with a light, activate

the light switch (item 4) make sure it activates the

light.

1

2

15

ASSEMBLY

INSTALLING THE SPRING AND

ADJUSTING THE LIFTING HEIGHT OF

THE SNOWBLOWER.

IMPORTANT:

It is very important that the snowblower engine does

not come into contact with the vehicle.

If necessary, use on each side one or two shims (item

2) supplied with the kit to limit the lifting height.

Secure in place with a hex bolt 3/8’’ x 1 1/2’’ (item 3),

a flat washer 7/16’’ (item 4) and a nylon insert lock nut

(item 5) as shown.

Lift the snowblower to its maximum height, insert the

spring (item 1) in the chain (item 6) and on the welded

rod (item 7) as shown.

Install the spring

VERIFYING THE ASSEMBLY

THE LENGTH OF THE SUBFRAME

When the vehicle is advancing in a straight line,

make sure the wheels of the subframe do not come

into contact with the wheels of the vehicle.

When the snowblower is raised to its maximum,

make sure the snowblower engine does not come

into contact with the vehicle.

PRESSURE OF THE TIRES ON THE

SUBFRAME

Verify and adjust the pressure of the tires of the

subframe at 50 psi.

The tire pressure must be even on both sides.

16

OPERATION

WARNING

Read the vehicle's owner’s manual carefully. Be

thoroughly familiar with the controls & proper use of

the attachment. Know how to stop the unit &

disengage the controls quickly.

WARNING

To prevent injuries and for more traction when using

the snowblower:

-Do not drive faster than 3 km/hr (2 m/hr) with

snowblower on the ground.

-Do not drive faster than 10 km/hr (6 m/hr) with the

snowblower in raised position.

-Always disengage the electromagnetic clutch when

the snowblower is in the raised position.

-Do not operate on a slope greater than 10%.

-Vehicle manufacturer approved tire chains are

required.

-Maximum drawbar pull provided for at the hitch

ball coupling: 3560N (800 lbs)

-Maximum vertical load provided for on the hitch

ball coupling: 360N (80 lbs).

-Ear muffs and safety glasses are recommended.

SNOWBLOWER OPERATION

1. Make sure the snowblower is clear of snow;

2. Make sure the auger and impeller operate freely.

3. Make sure the electromagnetic clutch is deactivated and

the kill switch is disengaged.

4. Start the snowblower engine

5. Before activating the electromagnetic clutch, the

snowblower engine must run at maximum R.P.M.

6. Operate the snowblower safely.

IMPORTANT: Use full engine r.p.m. when removing

wet, sticky snow. low r.p.m. power will tend to plug the

chute.

WARNING

Never touch with your hands or feet the snowblower’s

fan, auger or the chute because this is the most

frequent cause of accidents associated with

snowblowers.

DANGER

Never let the snowblower motor run without all

guards in place.

LIFTING AND LOWERING THE

SNOWBLOWER

Use the winch control switch to raise and lower the

snowblower.

IMPORTANT: To extend the lifespan of the subframe,

immediately release the switch when the accessory hits the

stopper in the raised position.

WARNING

To prevent accidents :

-Always use the snowblower in well lighted areas.

-It is essential to install and use a light on the front of

the snowblower for night use or in shadowy

conditions.

WARNING

TO PREVENT INJURIES:

Start the engine, engage and disengage the clutch to

be sure it functions normally. Make sure the

emergency switch is working perfectly. Make sure all

the controls are working well.

ELECTRICAL CONTROLS

See the ’’Installation of the control box’’ section for the

identification of the electrical controls of the snowblower.

BURNISHING PROCEDURE

The burnishing procedure must be performed before the

first utilisation of the snowblower and after a prolonged

period of inactivity. Burnishing the engaging system will

ensure proper performance and will help avoid damages.

1. Make sure the fan and the augers are free of any ob-

struction. Start the motor.

2. Engage electric clutch.

3. Disengage electric clutch and wait for all moving parts

to stop.

4. Repeat procedure (steps 2 & 3) 10 times.

ENGINE OPERATION

Operate the engine according to the instructions in the

engine’s owner’s manual.

17

OPERATION

SKID SHOE ADJUSTMENT

Level paved surface: Adjust skid shoes to allow 3/16”

to 1/4" or 5 mm to 7 mm clearance (A) between

cutting edge and surface.

Uneven or gravel surface: Adjust skid shoes to allow

1/2” to 5/8" or 13 mm to 16 mm clearance (A)

between cutting edge and surface.

Skid shoe adjustment

DANGER

DANGER ZONE

It is the snowblower operator’s obligation to make

sure there are no people or objects that can be

thrown in this zone when the snowblower is running.

SNOWBLOWING TECHNIQUE

When removing snow, do not use the snowblower as

a dozer blade to push snow. Allow snowblower to

ingest snow at its own speed. If the speed of your

A.T.V. is too fast, the snowblower may become

overloaded and plugged.

Danger zone

18

MAINTENANCE

ENGINE MAINTENANCE

Maintain the engine according to the instruction in the

engine’s owner’s manual.

SNOWBLOWER MAINTENANCE

Check mounting bolts at frequent intervals for proper

tightness in order to prevent costly repairs. Make sure

your snowblower is in safe working condition.

PRESSURE OF THE TIRES ON THE

SUBFRAME

Verify and adjust the pressure of the tires of the

subframe at 50 psi.

The tire pressure must be even on both sides.

WARNING

Before doing any snowblower maintenance,

assembling or dismounting:

Apply parking brakes of the vehicle.

Stop the snowblower engine and remove the

ignition key

Disconnect the wire from the spark plug(s) and

keep away from spark plug(s) to prevent

accidental starting.

CUTTING EDGE MAINTENANCE

Verify from time to time the wearing on the cutting

edge to make sure you do not wear out the base of

the snowblower’s chassis. This cutting edge is

reversible. Unscrew the bolts and turn the cutting

edge,

Reinstall with new carriage bolts 5/16’’ x 3/4’’ grade 5

and new lock nuts 5/16’’.

WARNING

If the snowblower is in the raised position,

always make sure to provide adequate blocking

before working under the snowblower.

SNOWBLOWER PULLEY REPLACEMENT

OR ALIGNMENT

Clean the parts before aligning or replacing the pulleys.

Apply some "Locktite" 2760 on the key and the set

screws. Tighten firmly.

WARNING

-Do not attempt to clear plugged chute, auger or

fan of snow while the snowblower's engine is

running.

-Disengage snowblower.

-Lower snowblower onto ground.

-Set the parking brake.

-Stop engine, remove the ignition key, disconnect

the wire from spark plug(s) and keep away from

spark plug(s) to prevent accidental starting.

-Make sure all moving parts have stopped.

-Do not use hand to unplug chute, use the chute

shovel supplied with the snowblower.

CLEANING A CLOGGED DISCHARGE

CHUTE

Whether it is the snowblower auger, the fan or the

chute that clogged, it is essential to follow these

instructions to the letter.

1. Disengage the electromagnetic clutch

2. Lower the snowblower to the ground and apply

the vehicle’s hand brake;

3. Stop the snowblower engine, remove the key and

wait for all the rotating parts to stop turning.

4. Disconnect the wire from the spark plug(s) and

keep away from spark plug(s) to prevent

accidental starting;

WARNING: Always use the chute shovel supplied with

the snowblower in order to unclog the snowblower,

never use your feet or hands.

La page est en cours de chargement...

Bercomac 700512-5-24H-EPA 700512-5-22.5K-EPA 700512-5-25K-EPA Manuel utilisateur

Ce manuel convient également à

Bercomac 700512-5-24H-EPA 700512-5-22.5K-EPA 700512-5-25K-EPA Manuel utilisateur

dans d''autres langues

Documents connexes