Wacker Neuson PT6LT Manuel utilisateur

Operator’s Manual

Pump

PT 6L

Notice d’Emploi

Pompe

5000185276 11 0613

5

000185276

EN-FR

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5000185252 11 0613

PT 6L Foreword

wc_tx003318gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Machine Item Number

PT 6LT

PT 6LS

0007175

0007174

wc_gr010619

Serial Number:

Foreword PT 6L

4 wc_tx003318gb.fm

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

 The illustrations, parts, and procedures in this manual refer to Wacker Neuson

factory-installed components. Your machine may vary depending on the

requirements of your specific region.

CALIFORNIA

Proposition

65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental

discharge of sparks or flames from the engine exhaust. Spark arresters are

qualified and rated by the United States Forest Service for this purpose. In order to

comply with local laws regarding spark arresters, consult the engine distributor or

the local Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Table of Contents

PT 6L

wc_bo5000185252_11TOC.fm

5

Foreword 3

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Safety Guidelines for Operating the Machine ..................................... 11

1.4 Service Safety .................................................................................... 13

1.5 Operator Safety while Using Internal Combustion Engines ............... 15

1.6 Safety Guidelines for Towing the Machine ......................................... 16

1.7 State Regulations Concerning Trailers ............................................... 17

1.8 Reporting Trailer Safety Defects ........................................................ 17

2 Labels 18

2.1 Label Locations .................................................................................. 18

2.2 Label Meanings .................................................................................. 19

3 Lifting and Transporting 23

3.1 Lifting the Machine ............................................................................. 23

3.2 Tires ................................................................................................... 24

3.3 Wheels and Lug Nuts ......................................................................... 24

3.4 Tongue Jack ....................................................................................... 24

3.5 Safety Chains ..................................................................................... 25

3.6 Lights .................................................................................................. 26

4 Operation 27

4.1 Preparing the Machine for First Use ................................................... 27

4.2 Control / Component Locations .......................................................... 28

4.3 Control / Component Descriptions ..................................................... 29

4.4 Recommended Fuel ........................................................................... 29

4.5 Before Starting the Engine ................................................................. 29

4.6 Before Starting the Pump ................................................................... 30

4.7 Starting ............................................................................................... 31

4.8 Stopping ............................................................................................. 32

4.9 Automatic Shutdown System ............................................................. 33

4.10 Hoses ................................................................................................. 33

4.11 Hose Couplings .................................................................................. 33

4.12 Hose Clamps ...................................................................................... 33

4.13 Strainer ............................................................................................... 34

Table of Contents

PT 6L

wc_bo5000185252_11TOC.fm

6

4.14 Discharge Port .....................................................................................34

4.15 Covers .................................................................................................35

4.16 Towing the Machine ............................................................................36

4.17 Emergency Shutdown Procedure ........................................................37

5 Maintenance 38

5.1 Periodic Maintenance Schedule ..........................................................38

5.2 Engine Fuel Delivery System Maintenance .........................................39

5.3 Servicing the Air Cleaner .....................................................................40

5.4 Maintaining the Fuel Filter ...................................................................41

5.5 Priming the Fuel System .....................................................................41

5.6 Checking Engine Oil Level ..................................................................42

5.7 Changing the Engine Oil .....................................................................43

5.8 Valve Clearances ................................................................................45

5.9 Fan Belt ...............................................................................................46

5.10 Pump Housing Mounting Bolts ............................................................47

5.11 Mechanical Seal Lubrication ...............................................................47

5.12 Bearing Housing Lubrication ...............................................................48

5.13 Impeller Inspection ..............................................................................49

5.14 Engine Cooling Fins ............................................................................50

5.15 Battery .................................................................................................51

5.16 Long-Term Storage .............................................................................52

6 Troubleshooting 53

7 Technical Data 54

7.1 Engine .................................................................................................54

7.2 Pump ...................................................................................................55

7.3 Lubrication ...........................................................................................55

7.4 Trailer and Skid ...................................................................................55

7.5 Dimensions ..........................................................................................56

8 AEM Safety Manual 57

Tire Safety Information 69

Table of Contents

PT 6L

wc_bo5000185252_11TOC.fm

7

9 Schematics 81

9.1 Trailer Wiring ...................................................................................... 81

9.2 Electrical Wiring

(0007174 < Rev 120; 0007175 < Rev 123) ........................................ 82

9.3 Electrical Wiring Components

(0007174 < Rev 120; 0007175 < Rev 123) ........................................ 83

9.4 Electrical Wiring

(0007174 > Rev 119; 0007175 > Rev 122) ........................................ 84

9.5 Electrical Wiring Components

(0007174 > Rev 119; 0007175 > Rev 122) ........................................ 85

Table of Contents

PT 6L

wc_bo5000185252_11TOC.fm

8

wc_si000767gb.fm

9

PT 6L Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000767gb.fm

10

Safety Information PT 6L

1.2 Machine Description and Intended Use

This machine is a centrifugal trash pump. The Wacker Neuson Trash Pump

consists of a trailer with integral fuel tank onto which are mounted a diesel engine,

and an impeller pump with ports for water suction and discharge. The engine

rotates the impeller during operation. Waste water is drawn into the pump through

the suction port and expelled through the discharge port. The operator connects

hoses to the pump and routes them so that water and solids are drained from the

work area and discharged into an appropriate location.

This machine is intended to be used for general de-watering applications. This machine

is intended for the pumping of clear water, or water containing solids up to the size

stated within the product specifications; and up to the flow, head, and suction lift limits

also stated within the product specifications.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

 Pumping flammable, explosive, or corrosive fluids

 Pumping hot or volatile fluids that result in pump cavitation

 Operating the pump outside of product specifications due to incorrect diameter

hoses, incorrect length hoses, other inlet or outlet restrictions, or excessive

suction lift or head

 Using the machine as a ladder, support, or work surface

 Using the machine to carry or transport passengers or equipment

 Operating the machine outside of factory specifications

 Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

 Heat, noise, exhaust, and carbon monoxide from the engine

 Fire hazards from improper refueling techniques

 Fuel and its fumes

 Personal injury from improperly lifting the trailer tongue

 Projectile hazard from discharge

 Crushing hazards from a tipping or falling pump (placing the vibrating pump on

an uneven surface or near the edge of a trench increases the risk of the pump

falling over)

 Typical hazards related to towing a trailer on roads and highways

wc_si000767gb.fm

11

PT 6L Safety Information

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

1.3 Safety Guidelines for Operating the Machine

Operator

training

Before operating the machine:

 Read and understand the operating instructions contained in all manuals

delivered with the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Contact Wacker Neuson for additional training if necessary.

When operating this machine:

 Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

 have received instruction on how to properly use the machine

 are familiar with required safety devices

The machine must not be accessed or operated by:

 children

 people impaired by alcohol or drugs

Application

area

Be aware of the application area.

 Keep unauthorized personnel, children, and pets away from the machine.

 Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

Be aware of the application area.

 Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Safety

devices,

controls, and

attachments

Only operate the machine when:

 All safety devices and guards are in place and in working order.

 All controls operate correctly.

 The machine is set up correctly according to the instructions in the Operator’s

Manual.

 The machine is clean.

 The machine’s labels are legible.

To ensure safe operation of the machine:

 Do not operate the machine if any safety devices or guards are missing or

inoperative.

 Do not modify or defeat the safety devices.

 Only use accessories or attachments that are approved by Wacker Neuson.

wc_si000767gb.fm

12

Safety Information PT 6L

Safe

operating

practices

When operating this machine:

 Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

When operating this machine:

 Do not operate a machine in need of repair.

 Do not consume the operating fluids used in this machine. Depending on your

machine model, these operating fluids may include water, wetting agents, fuel

(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic fluid,

heat transfer fluid (propylene glycol with additives), battery acid, or grease.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

Safe

operating

practices

 Do not open the priming plug when the pump is hot. Do not loosen or remove

inlet or discharge hose fittings when the pump is hot. Hot water inside could be

pressurized much like the radiator on an automobile. Allow the pump to cool to

the touch before loosening the plug and before loosening or removing the inlet

or discharge hose fittings.

 Do not position the pump on a loose, uneven, or unstable surface where it can

tip, roll, slide or fall! The pump must be secure before operating. Position the

pump on a firm, flat surface; adjust the trailer jacks to be sure the pump is level

and supported firmly.

 Do not open the pump housing cover while the pump is operating or start the

pump with the cover off. The rotating impeller inside the pump can cut or sever

objects caught in it.

 Do not block or restrict flow from the inlet line or the discharge line. Remove

kinks from the discharge line before starting the pump. Operation with a blocked

inlet line or discharge line can cause water inside the pump to overheat.

 Do not reach into or insert anything into the pump while the engine is on! The

impeller inside the pump housing is turning at all times while the engine is

running.

 Do not allow anyone to stand in front of the discharge port when starting the

engine or while priming the pump! The sudden out-rush of water could push or

knock a person down.

 Always make sure the hose connections on the pump are tight. A loose

connection could cause water to spray or result in a hose falling off the pump

while it is in operation.

 Always make sure the water stream from the pump discharge is not directed in

such a way so as to cause erosion to the surrounding ground or damage or

weakening of nearby structures!

wc_si000767gb.fm

13

PT 6L Safety Information

1.4 Service Safety

Service

training

Before servicing or maintaining the machine:

 Read and understand the instructions contained in all manuals delivered with

the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Only trained personnel shall troubleshoot or repair problems occurring with the

machine.

 Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

 Do not allow improperly trained people to service or maintain the machine.

Personnel servicing or maintaining the machine must be familiar with the

associated potential risks and hazards.

Precautions

Follow the precautions below when servicing or maintaining the machine.

 Read and understand the service procedures before performing any service to

the machine.

 All adjustments and repairs must be completed before operation. Do not

operate the machine with a known problem or deficiency.

 All repairs and adjustments shall be completed by a qualified technician.

 Turn off the machine before performing maintenance or making repairs.

Machine

modifications

When servicing or maintaining the machine:

 Use only accessories/attachments that are approved by Wacker Neuson.

When servicing or maintaining the machine:

 Do not defeat safety devices.

 Do not modify the machine without the express written approval of Wacker

Neuson.

Replacing

parts and

labels

 Replace worn or damaged components.

 Replace all missing and hard-to-read labels.

 When replacing electrical components, use components that are identical in

rating and performance to the original components.

 When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

Cleaning

When cleaning and servicing the machine:

 Keep the machine clean and free of debris such as leaves, paper, cartons, etc.

 Keep the labels legible.

When cleaning the machine:

 Do not clean the machine while it is running.

 Never use gasoline or other types of fuels or flammable solvents to clean the

machine. Fumes from fuels and solvents can become explosive.

wc_si000767gb.fm

14

Safety Information PT 6L

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

After Use

 Stop the engine when the machine is not being operated.

 Close the fuel valve, if equipped, when machine is not being operated.

 Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

 Store the machine in a clean, dry location out of the reach of children.

wc_si000767gb.fm

15

PT 6L Safety Information

1.5 Operator Safety while Using Internal Combustion Engines

Operating

safety

When running the engine:

 Keep the area around exhaust pipe free of flammable materials.

 Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine. Do not run the machine if fuel leaks are present or the fuel lines are

loose.

When running the engine:

 Do not smoke while operating the machine.

 Do not run the engine near sparks or open flames.

 Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

 Do not operate a machine when its fuel cap is loose or missing.

 Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

Refueling

safety

When refueling the engine:

 Clean up any spilled fuel immediately.

 Refill the fuel tank in a well-ventilated area.

 Replace the fuel tank cap after refueling.

 Use suitable tools for refueling (for example, a fuel hose or funnel).

When refueling the engine:

 Do not smoke.

 Do not refuel a hot or running engine.

 Do not refuel the engine near sparks or open flames.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

wc_si000767gb.fm

16

Safety Information PT 6L

1.6 Safety Guidelines for Towing the Machine

When towing the machine:

 Do not tow the machine if the towing vehicle’s hitch or the trailer’s coupler are

damaged.

 Do not tow the machine if any of the trailer’s lug nuts are missing.

 Do not tow the machine if the trailer’s tires have less than 1.5 mm (1/16 inch) of

tread.

 Do not tow the machine unless the trailer’s brakes are functioning properly.

 Do not exceed the trailer manufacturer’s speed limitations.

When towing the machine:

 Only tow the machine when the trailer’s lug nuts are properly torqued.

 Only tow the machine when the trailer’s tires are properly inflated.

 Only tow the machine when all trailer lights are functioning correctly.

 Only tow the machine when the trailer’s safety chains are connected to the

towing vehicle in a crisscross pattern.

 Maintain extra distance between the towing vehicle and other vehicles.

 Avoid soft shoulders, curbs, and sudden lane changes

 Abide by all licensing requirements for your area.

If you have not driven a towing vehicle with trailer before, practice turning,

stopping, and backing up the towing vehicle with trailer in an area away from traffic.

Only drive the towing vehicle with trailer when you are confident in your ability to do

so.

WARNING

Risk of severe injury or death. Improper trailer condition and towing technique can

lead to an accident.

f Obey the trailer manufacturer’s instructions and the instructions below to reduce

the risk of an accident.

wc_si000767gb.fm

17

PT 6L Safety Information

1.7 State Regulations Concerning Trailers

Trailer laws covering such things as brakes, lights, safety chains, etc., will vary

from state to state. Make certain that your trailer is in compliance with the

regulations of the state in which the trailer will be used. If you are not sure what

these regulations are, contact the state motor vehicle department for information.

In some states, trailers must be registered and licensed by the State Department of

Transportation. Before towing, be sure to check licensing requirements.

1.8 Reporting Trailer Safety Defects

If you believe your trailer has a defect which could cause a crash or could cause

injury or death, you should immediately inform the National Highway Traffic Safety

Administration (NHTSA) in addition to notifying Wacker Neuson.

If NHTSA receives similar complaints, it may open an investigation; and if it finds

that a safety defect exists in a group of vehicles, it may order a recall and remedy

campaign. However, NHTSA cannot become involved in individual problems

between you, your dealer, or Wacker Neuson.

To contact NHTSA, you may either contact the Auto Safety Hotline toll-free at 1-

800-424-9393 (or 366-0129 in Washington DC area), www.nhtsa.com, or write to

NHTSA, U.S. Department of Transportation, 400 7th Street SW, (NSA-11),

Washington, DC 20590. You can also obtain other information about motor vehicle

safety from the Auto Safety Hotline.

wc_si000768gb.fm

18

Labels PT 6L

2 Labels

2.1 Label Locations

wc_gr010680

A

B

C

D

E

F

G

J

A

E

K

DM

N

O

Q

R

S

T

U

P

V

H

wc_si000768gb.fm

19

PT 6L Labels

2.2 Label Meanings

A

NOTICE

No lift point

B

Low sulfur fuel or ultra low sulfur fuel only.

C

DANGER

Asphyxiation hazard.

 Engines emit carbon monoxide.

 Do not run the machine indoors or in an

enclosed area.

 NEVER use inside a home or garage, EVEN

IF doors and windows are open.

 Only use OUTSIDE and far away from

windows, doors, and vents.

 Read the Operator’s Manual.

 No sparks, flames, or burning objects near

the machine.

 Stop the engine before refueling.

CAUTION

Use only clean, filtered diesel fuel

D

CAUTION

Wheel nuts must be tightened to 85 ft.lbs.

E

WARNING

Pressurized contents. Do not open when hot!

wc_si000768gb.fm

20

Labels PT 6L

F

WARNING

Never pump volatile, flammable, or low-flash-

point fluids. These fluids could ignite or

explode.

G

CAUTION

Read and understand the supplied Operator’s

Manual before operating this machine. Failure to

do so increases the risk of injury to yourself and

others.

H

Notification of California emissions compliance

J

NOTICE

Lifting point

K

WARNING

Hot surface

La page charge ...

Wacker Neuson PT6LT Manuel utilisateur

Ce manuel convient également à

Wacker Neuson PT6LT Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents