Phase Technology CI140 Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
Rev 12.10.2019
CI140 | OWNER’S MANUAL
A A
B B
2
2
1
1
DO NOT SCALE DRAWING
CI140 Mktg Line Exploded Flipped
SHEET 1 OF 1
12/10/2019
ABOWERS
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:8
WEIGHT:
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
COMMENTS:
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
FINISH
MATERIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
APPLICATION
USED ON
NEXT ASSY
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
CI140 | OWNER’S MANUAL
Thank you for purchasing the Phase Technology
®
CI Custom Installation high denition in-wall speaker system. The mounting
grame of extruded aluminum has a uniquely designed self-aligning clamping system to secure the ange assembly to the
drywall. This patented design simplies installation and reduces unwanted wall vibration resulting in improved performance
and denition.
All CI Series speajkers include self-resetting solid-state PTC protection circuits. This unique system is able to detect when the
speaker is being over-driven and lowers the speaker volume until the problem is corrected. The PTC device then resets itself
for normal operation.
Regardless of application, serious audiophile listening or home theater, we recommend that you take the time to read this manual
thoroughly before connecting speakers to your amplier or receiver. In the highly unlikely event that you should experience a
problem with setup or operation, please contact one of our authorized dealers for assistance, or contact us directly at 913-
663-5600 or sales@mseaudio.com.
Safety Instructions
Explanation of Graphic Symbols
1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.
2. Retain Instructions - The safety and operating instructions should be retains for future reference.
3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.
4. Follow Instructions - All operating and other instructions should be followed.
CAUT IO N
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of electric shock, do not re-
move cover (or back). No user-serviceable parts inside. Re-
fer servicing to qualied service personnel.
The lighting ash with arrowhead symbol, within an equailateral triangle, is intended to alert you to the
presence of un-insulated dangerous voltage: within the product’s enclosure that may be off sufcient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is inteded to alert you to the presence of important
operating and maintenance {servicing) instructions in the literature accompanying the appliance.
5. Water and Moisture - The appliance should not be used near water - for example, near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool, etc.
6. Carts and Stands - The appliance should be used only with a cart or stand that is recommended by the manufacturer.
PORTABLE CART WARNING
7. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.
8. Ventilation - The appliance should be situated so that its location or position does not interfere with its proper ventilation. For
example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or
placed in a built-in installation, such as a bookcase or cabinet that may impede the ow of air through the ventilation openings.
9. Heat - The appliance should be situated away from heat sources such as radiators, stoves, or other appliances that produce
heat.
10. Power Source - The appliance should be connected to a power supply only of the type described in the operating
instructions or as marked on the appliance.
11. Power Cord Protection- Power supply cords should be routed so that they are not likely to be walked on or pinched by
items placed up or against them, paying particular attention to cords at plugs, convenience receptables, and the poiunt where
they exit from the appliance.
12. Cleaning - The appliance should be cleaned only as recommended by the manufacturer.
13. Nonuse Periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long period
of time.
14. Object and Liquid Entry - Care should be taken so that neither objects fall nor liquids spill into the inside of the appliance.
15. Damage Requiring Service - The application should be serviced by qualied service personnel when:
• The power supply cord or the plug has been damaged.
• Objects have follen onto or liquid has been spilled into the appliance
• The appliance has been exposed to rain
• The appliance does not appear to operate normally or exhibits a marked changed in performance
• The appliance has been dropped or the cabinet damaged.
16. Servicing - The user should not attempt to service the appliance beyond those means described in the operating
instructions. All other servicing should be referred to qualied service personnel.
17. Grounding or Polarization - Precautions should be taken so that the grounding or polarization means of an appliance is
not defeated.
Applicable for USA, Canada, or
where approved for usage.
CAUTION: To prevent electric shock,
match wide blade plug to wide slot,
insert fully.
ATTENTION: Pour eviter les chocs electriques,
introduire la lame la plus large de la che dans la
borne correspondante de la prese et pousser jusqu
au fond
Installation Guidelines
When selecting the speaker mounting location, it is prudent to take a few extra minutes to carefully inspect and measure the
wall or ceiling area where you intend to mount the CI in-wall speaker. An inspection of the room or rooms that back-up to the
wall you have selected for mounting the CI in-wall speaker, can often alert you to potential obstacles. For example, if the wall
you want to mount into happens to be in the common wall for a bathroom or kitchen, there is a good chance you will encounter
water or sewer pipes in the wall that will not be detected by a stud-nder. An electronic stud-nder is a useful tool to assist you
in selecting the speaker placement, however be cautious as they often give false readings.
Choose the appropriate mounting location for each speaker. NOTE: When deciding upon a location, consider the following:
• Be certain your speaker wires can be run to or are accessible from these locations.
• Make certain the wall or ceiling material is sturdy enough to support the weight and vibration of the speakers.
• It is recommended that our pre-construction rough-in brackets be used whenever possible in new construction.
• Be certain the area behind the speaker is free of obstacles such as wall studs, electrical wiring, pipes, etc.
• Each speaker should be positioned properly, relative to the listening area for good coverage.
• Audio performance and room-to-room isolation will be improved if there is some berglass insulation placed loosely
above and below the speaker.
Speaker Installation
STEP 1: The cutout opening for the CI140 is 13.4” H x 13.25” W. Place the cutout template against the wall surface and align
it using your bubble level and tape measure. Hold, tape, or staple the template in place and trace around the perimeter of the
template with a pencil. Remove the template and begin cutting on the pencil line.
STEP 2: When the cutout is complete, carefully remove the drywall piece from the opening. You now have a large opening to
facilitate pulling your speaker wire. We recommend 16 gauge or heavier wire be used with the CI speaker. Contact your Phase
Technology
®
Dealer for a recommendation.
STEP 3: Carefully remove the speaker bafe from the aluminum frame assembly and set aside. Remove the ange assembly
from the packing carton. The ange assembly must make a good seal to ensure maximum performance. You will nd two
L-shaped foam gasket pieces in the bottom of the carton. Peel the removable tape from the gasket and stick the adhesive side
to the backside of the frame ange. Upon installation of the ange assembly the gasket will contact the front wall surface to
form an airtight seal.
STEP 4: When you remove the ange assembly from the packing carton, you will notice the screws used to retain the clamp
assembly are fully extended. To place the ange assembly into the wall, push the clamp assemblies toward the center of the
ange opening; the holes in the ange will allow the mounting screws to tilt toward the center opening enough to insert the
ange assembly into the wall. Insert the right side into the wall cutout and slide the complete assembly to the right. This will
enable you to then t the left side clamp assembly into the cutout. Center the entire assembly in the opening.
STEP 5: Pinch the self-aligning clamp assembly inside the wall until it contacts the backside of the drywall surface. This will
force the three retaining screws to produce from the front of the ange. Continue to hold the clamp with one hand and use the
electric screwdriver to tighten the center screw of the ange. Once snug, repeat the procedure on the other clamp assembly.
Using your level, verify the mounting frame is correctly aligned in the opening. Make any necessary adjustments, then tighten
the remaining screws until the frame is snug and securely clamping the wallboard. Avoid over-tightening the screws.
STEP 6: You are now ready to install the speaker bafe into the mounting ange.
CI140: The CI140 has a nylon terminal block on the top end of the enclosure. Connect your speaker lead wire to the terminal
block and secure teh stripped ends of your speaker wire by tightening down the screw terminals, the red wire to the positive,
and the black to the negative.
STEP 7: You are now ready to install the speaker bafe into the mounting ange. Carefully insert the speaker bafe into the
wall ange until it bottoms out against the ange. Six screws are supplied to secure the bafe to the ange. Hold the bafe in
position and start 1 screw each at the opposite corners of the bafe but leave loose. Start the other 4 screws through the bafe
into the frame. Now snug down all 6 screws being careful not to over tighten them.
STEP 8: Place the magnetic grille over the ange assembly. This speaker grille may be painted as desired to match the wall
color. Most standard paints can be used and it is recommended that the paint be sprayed on using several light coats so the
perforated holes in the grille are not obstructed.
Caring for Your Phase Technology® Speaker
All Phase Technology speakers are nished with a high degree of craftsmanship in either hand polished paint or vinyl laminates.
We recommend using a lint-free rag with a small amount of glass cleaner to maintain the long-lasting beauty of the nish. Avoid
products containing silicones, oils, oil derivatives, or solvents. Use a damp cloth on enclosures nished in vinyl laminates.
Maintenance and Service
Because of Phase Technology’s uncompromising quality control programs, it’s unlikely that your speakers will ever need
service if connected and sued as outlined in this owner’s manual. In the unlikely event that a problem does occur, please
contact your Phase Technology dealer. Your dealer has the necessary factory-authorized parts and trained technicians to
quickly restore your speaker to its original performance specications.
Warranty
Phase Technology warrants its loudspekaers to be free from defects in material and workmanship for a period of ten (10) years
for speaker product, limited lifetime for CI speakers, and three (3) years for the electronic components to the original purchaser.
Purchase must be made from an authorized Phase Technology dealer.
This warranty does not cover service or parts to repair damage caused by misuse, abuse, damage while in transit, alterations,
unauthorized repairs, failure to follow instructions, re, ood, or any other cause beyond the reasonable control of Phase
Technology. Defects in speaker cabinets or grilles must be brought to the attention of your dealer immediately after purchase.
This warranty will be void if the products’ serial number has been altered or removed.
Should your Phase Technology product require service, please call the MSE Audio customer service department for a return
authorization. All merchandise returned to Phase Technology without prior authorization will be refused. For your return
authorization number, please call 913.663.5600 or email sales@mseaudio.com.
Phase Technology
®
by MSE Audio
®
| 10661 Rene St. | Lenexa, KS 66215
913-663-5600 or 855-663-5600 | www.phasetech.com
-
1
-
2
-
3
-
4
-
5
