Ironman Fitness 6839 Le manuel du propriétaire

The specifications of this product may vary from this photo and are subject to change without notice.

IRONMAN, IRONMAN TRIATHLON and M-DOT are registered trademarks of World Triathlon Corporation.

This product is licensed by the World Triathlon Corporation.

OWNER’S MANUAL

Leg Develop Attachment

6839.2‐050516



SERVICE-------------------------------------------------------------------- 2

LABEL PLACEMENT----------------------------------------------------- 3

PRODUCT SAFETY------------------------------------------------------ 4

ASSEMBLY PREPARATION-------------------------------------------- 5

OVERVIEW------------------------------------------------------------------ 6

HARDWARE PACK-------------------------------------------------------- 7

PART LIST------------------------------------------------------------------- 8

STEP 1----------------------------------------------------------------------- 10

STEP 2----------------------------------------------------------------------- 12

STEP 3----------------------------------------------------------------------- 14

STEP 4----------------------------------------------------------------------- 16

ADJUSTMENTS------------------------------------------------------------ 19

WARRANTY----------------------------------------------------------------- 20

PARTS REQUEST FORM----------------------------------------------- 21

TABLEOFCONTENT

1

IMPORTANT: FOR NORTH AMERICA ONLY

For damage or defective product, questions, replacement parts or any other service

support, please contact our customer service department (8:00 AM - 5:00 PM Pacific

Standard Time, Open Daily) by below methods:

For Best Service Email:

Service@paradigmhw.com

Website:

www.paradigmhw.com

Toll-Free:

1-844-641-7922

Please have the following information ready when requesting for service:

 Your name

 Phone number

 Model number

 Serial number

 Part number

 Proof of Purchase

For damaged or defective product please contact our customer service

before returning to the store.

* Emailing us with the information above will be the best method to

receive a response during peak business hours.

**Response time may vary.

Paradigm Health & Wellness, Inc.

1189 Jellick Ave.

City of Industry, CA 91748, USA

SERVICE

2

UNDER PENALTY OF LAW THIS TAG

NOT TO BE REMOVED EXCEPT BY THE

CONSUMER

NOTICE

This article does not meet

requirements of California

Bureau of Home Furnish-

ings technical bulletin 117.

Care should be exercised

burning cigaretts.

ALL NEW MATERIALCONSISTING

OF POLYURETHANE

FOAM PAD_100%

REGISTRY NO. VA25302 (CN)

manufacturer that the materials

in this article are described in

accordance with law.

Paradigm Health and Wellness, Inc.

1189 Jellick Ave. City of Industry

CA 91748, USA

Paradigm Health and Wellness, Inc.

1189 Jellick Ave. City of Industry, CA

91748 USA

SE SANCIONARÁ LEGALMENTE A

QUIENES QUITEN ESTA ETIQUETA.

SOLO EL CONSUMIDOR PODRÁ

QUITARLA.

MATERIAL COMPLETAMENTE NUEVO

COMPUESTO DE 100% RELLENO DE

ESPUMA DE POLIURETANO.

NOTIFICACIÓN

Este artículo no se ajusta a

Mobiliario boletín técnico

117. Cuidado de California

deben ejercerse cerca de

una llama abierta o con

cigaretts ardientes.

NO. DE REG VA25302 (CN)

materiales de este artículo se

describen según las leyes.

Paradigm Health and Wellness, Inc.

1189 Jellick Ave. City of Industry

CA 91748, USA

SOUS PEINE DE SANCTION LÉGALE,

CETTE ÉTIQUETTE NE PEUT ÊTRE

ENLEVÉE PAR UNE PERSONNE AUTRE

QUE LE CONSOMMATEUR

AVIS

Ce produit ne satisfait pas

-

du devis technique du

California Bureau of Home

Furnishings. Ne pas utiliser

près d’une source de

nue (cigarettes, etc.)

ENTIÈREMENT FABRIQUÉ DE

MATÉRIAUX NEUFS REMBOURRAGE

DE MOUSSE DE

POLYURÉTHANE 100 %

NO D’ENREGISTREMENT

VA25302 (CN)

Cette étiquette est apposée

conformément aux lois Cana-

diennes.

LABELPLACEMENT

3

WARNING: Before using this equipment you should consult with your personal physician to

see if Ironman Leg Development Attachment is appropriate for you. Do not use this

equipment without your physician’s approval. Do not use this equipment if you have any

of the following conditions or ailments:

 Extreme obesity

 Glaucoma, retinal detachment or conjunctivitis

 Pregnancy

 Spinal injury, Cerebral Sclerosis, or acutely swollen joints

 Middle ear infection

 High blood pressure, Hypertension, Recent stroke or Transient ischemic attack

 Heart or circulatory disorders for which you are being treated

 Hiatus hernia or Ventral hernia

 Bone weaknesses including Osteoporosis, Unhealed fractures, Modularly pins, or Surgically

implanted orthopedic supports

 Use of anti-coagulants including Aspirin in high doses

The Maximum Weight Capacity for this product is 180lbs/82kgs.

Read all instructions carefully before assembling or operating this product. Retain this

owner’s manual, do not remove any safety labels from the machine and keep the original

purchase receipt for future reference.

This Leg Development Attachment was designed and built for optimum safety. However, certain

precautions apply whenever you use the exercise equipment. Be sure to read the entire manual

before assembling and operating this equipment. Also, please note the following safety

instructions:

1. Consult your physician or other health care professionals before using the piece of equipment.

2. Always wear proper exercise apparel when using the equipment. Use care when getting on or

off the unit.

3. If any time you feel faint, light-headed or dizziness while operating the equipment, stop

exercising immediately and contact your physician. You should also discontinue use if you

are experiencing pain or any discomfort.

4. Keep children and pets away from the equipment at all times.

5. Only one person should use the equipment at a time.

6. Make sure your equipment is correctly assembled before you use it. Be sure all screws, nuts,

and bolts are tightened prior to use. Check screws, nuts, and bolts are tight on a weekly basis.

7. Do not operate this or any exercise equipment if it is damaged.

8. Wait 2 hours after eating before using the exercise equipment. If you get nauseous, stop

exercising as soon as you feel queasy.

9. This product should be placed on a flat surface when using. A mat or other covering material

on the ground is recommended. For indoor use only, do not use outdoors.

10. Keep hands and feet away from any moving parts. Do not insert any object into any

openings on the equipment.

11. Keep loose clothes, jewelry, limbs and long hair away from moving parts.

12. Children under the age of 12 should not use this fitness equipment.

4

PRODUCTSAFETY



Warning: It is highly recommend that you have assistance during the assembly of this

IRONMAN strength equipment.

1. Tools for assembly:

General tools you may need for the assembling this IRONMAN strength equipment:

 Metric Allen Key Set

 Metric Wrench Set and Adjustable Wrench

 Flat Screwdrivers

 Phillips Screwdrivers

 Rubber Mallet

 Silicone Spray Oil

2. Insert the bolts into the frame as illustrated in the drawing of each of the steps.

3. Hand-tighten the bolts, nuts, and screw during assembly. Hand-tightening will allow for easily

aligning the parts during assembly. Tighten all the hardware once the entire unit has been

completely assembled.

4. It is highly recommended that a professional installer assembles the IRONMAN strength

equipment. But, with the proper assistance, the right tools, and strictly following the assembly

steps, and given enough time; the assembly of the unit can be achieved without professional

help.

5. Thoroughly read each step before proceeding to assemble the items of that step.

6. To aid in assembly of the equipment, the hardware (bolts, nuts, washer…etc.) has been

presorted according to their corresponding steps. Each bag of hardware is labeled with its

corresponding step number.

7. When the equipment is fully assembled check all the functions for correct operation. Consult the

manual if you experience any issues, or for further help please contact our service department.

See page 2.



5

ASSEMBLYPREPARATION

OVERVIEWDRAWING

6

HARDWAREPACK

7

Part# Description Q’ty.

A Main Frame Post 1

101 Push Pin D8x55L 1

B

Leg Development

Tube

1

120

Round Cap

D25.4xD65x31.5

5

C Handlebar 1

125

Round Cap

D50.8x15

2

D Preacher Curl Post 1

126 Round Cap D1"x17 4

E Preacher Curl Pad 1

153

Square Cap

50x50x20L

1

F

Foam Roller Tube

D25.4x2.0Tx450L

2

155

Square Cap

30x70x17L

2

G

Rotating Axle

D12x58.5L

1

185

Buffer

D35xD25.5x24

1

2

Hex Bolt

M8x1.25x20L

2

186 Buffer R23x35x35 1

3 Hex Bolt M8x1.25x25L 4

200

Hand Grip

D24x3Tx300L

2

11

Allen Screw

M6x1x10L

1

222

Foam Roller

D23xD100x200L

6

50

Flat Washer

D18xD8.5x1.2T

4

223 Foam Roller Sleeve 6

53

Flat Washer

D25xD8.5x2T

3

250 Bearing 2

54

Spring Washer

D15.4xD8.2x2T

6

272 Bushing D20x26.4L 1

100 Push Pin D9.4x70 1

295 Standard Clip 1

PARTLIST



8

PARTLIST



9

Appearance upon completion of Step 1.

1A. Attach Leg Development Tube (B) onto the Main Frame Post (A) by using:

2 - (2) Hex Bolt M8x1.25x20L

2 - (54) Spring Washer D15.4xD8.2x2T

2 - (53) Flat Washer D25xD8.5x2T

1 - (G) Rotating Axle D12x58.5L

Thoroughly tighten the hardware once complete

STEP1

10

8

NO.2 Hex Bolt

M8x1.25x20L

2PCS

NO.53 Flat Washer

D25xD8.5x2T

2PCS

NO.54 Spring Washer

D15.4xD8.2x2T

2PCS

NO.G Rotating Axle

D12x58.5L

1PC

STEP1

11

13

,

15 mm Wrench 2PCS

Appearance upon completion of Step 2.

2A. Attach 2 Foam Rollers and Foam Roller Sleeve (222, 223) onto the circular

tubes on Main Frame Post (A) and secure them into place with 2 Round Cap (120)

using:

2 - (222) Foam Roller D23xD100x200L

2 - (223) Foam Roller Sleeve

2 - (120) Round Cap D25.4xD65x31.5

2B. Insert a Foam Roller Tube (F) into the hole at the bottom of Leg Development

Tube (B). Attach a Foam Roller and Foam Roller Sleeve (222, 223) to each side of

the Foam Roller Tube (F). Secure each Foam Roller and Foam Roller Sleeve (222,

223) into place with a Round Cap (120) at each end of Foam Roller Tube (F). Using:

2 - (222) Foam Roller D23xD100x200L

2 - (223) Foam Roller Sleeve

2 - (120) Round Cap D25.4xD65x31.5

2C. Insert a Foam Roller Tube (F) mid-way along its length into one of the holes at

the upper portion of Leg Development Tube (B). Attach a Foam Roller and Foam

Roller Sleeve (222, 223) to each side of the Foam Roller Tube (F). At one end of

Foam Roller Tube (F) use a Round Cap (120), and at the other end use a Round

Cap (126). Using:

2 - (222) Foam Roller D23xD100x200L

1 - (120) Round Cap D25.4xD65x31.5

1 – (126) Round Cap Round Cap D1"x17

Note: The Foam Roller Tube (F) of step 2C is meant to have two different types of

end caps. This will allow for the easy removal of this set of foam rollers when

performing preacher curls.

Warning: The foam rollers in step 2C must be removed in order to perform

preacher curl exercises or leg extensions.

STEP2

12

STEP2

13

NO.126 Round Cap

D1’’X17 1 PC

NO.120 Round Cap

D25.4xD65x31.5

5 PCS

Appearance upon completion of Step 3.

3A. Slide Preacher Curl Post (D) into the Square tube of the Main Frame Post (A).

Secure Preacher Curl Post (D) to Main Frame Post (A) with Push Pin (101). Using:

1 - (101) Push Pin D8x55L

3B. Attach Handlebar (C) to Leg Development Tube (B) with Push Pin (100). Using:

1 - (100) Push Pin D9.4x70

STEP3

14

15

STEP3

D.101 Push Pin

D8x55 1PC

NO.100 Push Pin

D9.4x70 1PC

Appearance upon completion of Step 4.

4A. Attach the Preacher Curl Pad (E) to the Preacher Curl Post (D) as shown in

diagrams AA-1 and AA-2 using:

4 - (3) Hex Bolt M8x1.25x25L

4 - (50) Flat Washer D18xD8.5x1.2T

4 - (54) Spring Washer D15.4xD8.2x2T

Note: Loosely insert all the hardware by hand first. This will allow for all the holes to

be aligned prior to fastening.

4B. When all the Hex Bolt (2) have been inserted, proceed to tightening the bolts to

completely secure the Preacher Curl Pad (E) to the Preacher Curl Post (D).

STEP4

16

STEP4

NO.50 Flat Washer

D18xD8.5x1.2T

4PCS

NO.54 Spring Washer

D15.4xD8.2x2T

4PCS

NO.3 Hex Bolt

M8x1.25x25L

4PCS

17

13,15 mm Wrench 1PC

Install the Standard Clip (295), please follow the steps below:

A. To secure your weight plates, pinch the rubber grips of Standard Clip (295).

B. Slide the Standard Clip (295) on to the post of the Leg Development Tube (B).

C. Standard Clip (295) should be pushed all the way down until it makes contact with

the weight plates, securing the weight plates to the backside of the weight post of

the Leg Development Tube (B).

Warning: DO NOT use weight plates on the post of Leg Development Tube (B)

without first securing them in place with the Standard Clip (295).

ClipInstallation

18

La page charge ...

Ironman Fitness 6839 Le manuel du propriétaire

Ironman Fitness 6839 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents