Panasonic EY75A1 Operating Instructions Manual

Taper
Operating Instructions Manual

Ce manuel convient également à

Cordless Impact Driver/Cordles Impact Wrench
Akku-Schlagschrauber/Akku-Schlagschrauber
Perceuse à impact sans l/Perceuse à impact sans l
Avvitatore ad impulsi senza li/Avvitatore ad impulsi senza li
Snoerloze slagschroevendraaier/Snoerloze slagschroevendraaier
Destornillador de impacto inalámbrico/Destornillador de impacto inalámbrico
Akku-slagboremaskine/Akku-slagboremaskine
Sladdlös slagskruvdragare/Sladdlös slagskruvdragare
Trådløs slagbormaskin/Trådløs slagbormaskin
Langaton iskuruuviavain/Langaton iskuruuviavain
Model No: EY75A1/EY75A2
Operating Instructions
Bedienungsanleitung
Instructions d’utilisation
Istruzioni per l’uso
Gebruiksaanwijzing
Manual de instrucciones
Brugsvejledning
Driftsföreskrifter
Bruksanvisning
Käyttöohjeet
Before operating this unit, please read these instructions completely and save this manual for future use.
Vor Inbetriebnahme des Gerätes die Betriebsanleitung bitte gründlich durchlesen und diese Broschüre zum späteren Nachschlagen sorgfältig aufbewahren.
Lire entièrement les instructions suivantes avant de faire fonctionner l’appareil et conserver ce mode d’emploi à des fins de consultation ultérieure.
Prima di usare questa unità, leggere completamente queste istruzioni e conservare il manuale per usi futuri.
Lees deze gebruiksaanwijzing aandachtig door voor u het apparaat in gebruik neemt en bewaar de gebruiksaanwijzing voor eventuele naslag.
Antes de usar este aparato por primera vez, lea todas las instrucciones de este manual y guarde el manual para poderlo consultar en el futuro.
Gennemlæs denne betjeningsvejledning før brugen og gem den til fremtidig brug.
Läs igenom hela bruksanvisningen innan produkten tas i bruk. Spara bruksanvisningen för senare användning.
Før enheten tas i bruk, vennligst les disse alle anvisningene og oppbevar bruksanvisningen for senere bruk.
Lue ohjeet huolella ennen laitteen käyttöönottoa ja säilytä tämä käyttöohje tallessa tulevaa tarvetta varten.
-
2
-
FUNCTIONAL DESCRIPTION
FUNKTIONSBESCHREIBUNG
DESCRIPTION DES FONCTIONS
DESCRIZIONE DELLE FUNZIONI
FUNCTIEBESCHRIJVING
DESCRIPCIÓN FUNCIONAL
FUNKTIONSBESKRIVELSE
FUNKTIONSBESKRIVNING
FUNKSJONSBESKRIVELSE
TOIMINTOJEN KUVAUS
9ņV
Index/Index/Index/Indice/Index/Indice/Indeks/Index/Indeks/Hakemisto/
Индекс/Індекс
English: Page 5
Deutsch: Seite 19
Français: Page 32
Italiano: Pagina 45
Nederlands: Bladzijde 58
Español: Página 71
Dansk: Side 84
Svenska: Sid 97
Norsk: Side 110
Suomi: Sivu 123
(Q)
(F)
(O)
(N)(M)
(A)
(B)
(C)
(D)
(E)
(G)
(K)
(P)
(I)
(J)
(L)
(R)
(A)
(H)
-
3
-
(A)
6.35 mm hex quick connect chuck
6,35 mm Sechskant-Schnellaufspannfutter
Mandrin de connexion rapide hexagonal de 6,35 mm
Mandrino esagonale di collegamento rapido da 6,35 mm
6,35 mm zeskantboorkop met snelkoppeling
Mandril hexagonal de conexión rápida de 6,35 mm
6,35 mm hexagonal borepatron til hurtig tilslutning
Snabbchuck med 6,35 mm sexkantshylsa
6,35 mm hex hurtigtilkoplingschuck
6,35 mm kuusiopikaistukka
(A)’
Square drive (ball detent)
Vierkant-Werkzeugaufnahme (Kugelraste)
Mandrin
Mandrino
Boorkop
Portabroca
Borepatron
Fyrkantig drivbult (med kulspärr)
Chuck
Kiinnityslaite
(B)
Nose protector
Frontabdeckung
Protection du bec
Protezione frontale
Neusbeschermer
Protector del morro
Næsebeskytter
Nosskydd
Nesebeskytter
Kärjen suojus
(C)
Forward/Reverse lever
Vorwärts-/Rückwärtshebel
Levier d’inversion marche avant/marche arrière
Leva di avanzamento/inversione
Links/rechtsschakelaar
Palanca de avance/marcha atrás
Greb til forlæns/baglæns retning
Riktningsomkopplare
Forover-/bakoverbryter
Eteenpäin/taaksepäin vipu
(D)
Belt hook lock lever
Riemenhaken-Verriegelungshebel
Levier de verrouillage du crochet de ceinture
Leva di blocco gancio da cintura
Borghendel voor riemclip
Palanca de bloqueo del gancho de cinturón
Låsehåndtag til bæltekrog
Låsknapp för bälteskrok
Låsespak for beltekrok
Vyölenkin lukitusvipu
(E)
Belt hook
Riemenhaken
Crochet de ceinture
Gancio da cintura
Riemclip
Gancho del cinturón
Bæltekrog
Bälteskrok
Beltekrok
Vyölenkki
(F)
Alignment marks
Ausrichtmarkierungen
Marques d’alignement
Marcature allineamento
Uitlijntekens
Marcas de alineación
Flugtemærker
Anpassningsmärken
Opprettingsmerke
Sovitusmerkit
(G)
Battery pack release button
Akku-Entriegelungsknopf
Bouton de libération de batterie autonome
Tasto di rilascio pacco batteria
Accu-ontgrendeltoets
Botón de liberación de batería
Udløserknap til batteripakning
Frigöringsknapp för batteri
Utløserknapp for batteripakke
Akkupaketin irrotuspainike
(H)
Battery pack
Akku
Batterie autonome
Pacco batteria
Accu
Batería
Batteripakning
Batteri
Batteripakke
Akku
(I)
LED light
LED-Leuchte
Lumière DEL
Luce LED
LED-lampje
Luz indicadora
LED-lys
LED-ljus
LED-lys
LED-valo
(J)
Control panel
Bedienfeld
Panneau de commande
Pannello di controllo
Bedieningspaneel
Panel de control
Kontrolpanel
Kontrollpanel
Kontrollpanel
Säätöpaneeli
(K)
LED light ON/OFF button
LED-Leuchten-EIN/AUS-Taste
Bouton Marche/Arrêt de la lumière DEL
Tasto di accensione e spegnimento della luce LED
Aan/uit-toets (ON/OFF) voor LED-lampje
Botón ON/OFF de luz LED
TÆND/SLUK-knap til LED-lys
Strömbrytare för LED-ljus
PÅ/AV-knapp for LED-lys
LED-valon kytkin/katkaisupainike
-
4
-
(L)
Impact power mode button
Schlagkraftmodus-Wahltaste
Bouton du mode de puissance de percussion
Tasto modalità potenza impatto
Slagkrachtfunctietoets
Botón de modo de potencia de impacto
Slagkraftfunktionsknap
Slagkraftsväljare
Knapp for slagstyrketype
Iskutehomuodon painike
(M)
Impact power mode display
Schlagkraftmodusanzeige
Af chage du mode de puissance de percussion
Display modalità potenza impatto
Slagkrachtfunctiedisplay
Indicación de modo de potencia de impacto
Slagkraftfunktionsdisplay
Slagkraftsindikering
Fremviser av slagstyrketype
Iskutehomuodon merkkivalo
(N)
Battery low warning lamp
Akkuladungs-Warnlampe
Témoin d’avertissement de batterie basse
Spia avvertenza batteria scarica
Waarschuwingslampje voor lage accuspanning
Luz de aviso de baja carga de batería
Advarselslampes batterieffekt lav
Varningslampa för svagt batteri
Varsellampe for at batteriet er for lavt
Alhaisen akkujännitteen varoituslamppu
(O)
Overheat warning lamp (motor/battery)
Überhitzungs-Warnlampe (Motor/Akku)
Témoin d’avertissement de surchauffe (moteur/batterie)
Spia avvertenza surriscaldamento (motore/batteria)
Oververhitting-waarschuwingslampje (motor/accu)
Luz de advertencia de sobrecalentamiento (motor/batería)
Advarselslamp til overophedning (motor/batteri)
Varningslampa för överhettning (motor/batteri)
Varsellampe for overoppheting (motor/batteri)
Ylikuumenemisen varoituslamppu (moottori/akku)
(P)
Variable speed control trigger
Variabler Geschwindigkeitskontrollschalter
Gâchette de commande de vitesse
Grilletto di controllo velocità variabile
Startschakelaar met variabele toerentalregeling
Disparador del control de velocidad variable
Kontroludløser for variabel hastighed
Avtryckare med variabel varvtalsreglering
Trinnløs hovedbryter
Nopeudensäätökytkin
(Q)
Battery charger
Ladegerät
Chargeur de batterie
Caricabatterie
Acculader
Cargador de batería
Batterioplader
Batteriladdare
Batterilader
Akkulaturi
(R)
Pack cover
Akkuabdeckung
Couvercle de la batterie autonome
Coperchio pacco
Accudeksel
Cubierta de batería
Pakningsdæksel
Batteriskydd
Pakkedeksel
Akkukotelon kansi
-
5
-
I.
ADDITIONAL
SAFETY RULES
1
) Wear ear protectors when using the
tool for extended periods.
2) Be aware that this tool is always in an
operating condition, since it does not have
to be plugged into an electrical outlet.
3) When screwing or driving into walls, floors,
etc., “live” electrical wires may be encoun-
tered. DO NOT TOUCH THE HEX QUICK
CHUCK OR ANY FRONT METAL PARTS
OF THE TOOL! Hold the tool only by the
plastic handle to prevent electric shock in
case you screw or drive into a “live” wire.
4) Do NOT operate the Forward/Reverse
lever when the main switch is on. The bat-
tery will discharge rapidly and damage to
the unit may occur.
5) During charging, the charger may become
slightly warm. This is normal.
Do NOT charge the battery for a long peri-
od.
6) When storing or carrying the tool, set the
Forward/Reverse lever to the center posi-
tion (switch lock).
7) Do not strain the tool by holding the speed
control trigger halfway (speed control
mode) so that the motor stops.
Symbol Meaning
V
Volts
Direct current
n
0
No load speed
… min
-1
Revolutions or reciprocations
per minutes
Ah
Electrical capacity of battery
pack
Read the operating
instructions before use.
For indoor use only.
WARNING:
Do not use other than the Panasonic
battery packs that are designed for use
with this rechargeable tool.
Panasonic is not responsible for any
damage or accident caused by the use of
recycled or counterfeit battery pack.
Do not dispose of the battery pack in a
fire, or expose it to excessive heat.
Do not drive the likes of nails into the battery
pack, subject it to shocks, dismantle it, or
attempt to modify it.
Do not allow metal objects to touch the
battery pack terminals.
Do not carry or store the battery pack
in the same container as nails or similar
metal objects.
Do not charge the battery pack in a
high-temperature location, such as next
to a fire or in direct sunlight. Otherwise,
the battery may overheat, catch fire, or
explode.
Never use other than the dedicated
charger to charge the battery pack.
Otherwise, the battery may leak, overheat,
or explode.
Original instructions: English
Translation of the original instructions:
Other languages
Read “the Safety Instructions” booklet
and the following before using.
-
6
-
After removing the battery pack from
the tool or the charger, always reattach
the pack cover. Otherwise, the battery
contacts could be shorted, leading to a
risk of fire.
• When the Battery Pack Has Deteriorated,
Replace It with a New One. Continued
use of a damaged battery pack may result
in heat generation, ignition or battery
rupture.
II. ASSEMBLY
Attaching or Removing Bit
NOTE:
When attaching or removing a bit, discon-
nect battery pack from tool or place the
switch in the center position (switch lock).
1. Hold the collar of quick connect chuck and
pull it out from the driver.
2. Insert the bit into the chuck. Release the
collar.
3. The collar will return to its original position
when it is released.
4.
Pull the bit to make sure it does not come out.
5. To remove the bit, pull out the collar in the
same way.
CAUTION:
If the collar does not return to its origi-
nal position or the bit comes out when
pulled on, the bit has not been properly
attached. Make sure the bit is properly
attached before use.
Use 6.35 mm hexagonal bits.
To ensure proper securement of the bit, use
only hexagonal bits with 9.5 mm detent.
6.35 mm
9.5 mm
Attaching or Removing
Sock et
1. Attaching Socket
Attach the socket by sliding the female
detent on the bottom of the socket to the
square drive on the body.
Make sure the
socket is firmly
connected to
the body.
2. Removing Socket
Pull out the socket.
NOTE:
Attaching or Removing Original Options
and Sockets
Keep the body above freezing point
(0°C 32°F) when attach or detach
original options and sockets to the
square drive on the body. The cushion
rubber in the square drive to push up
the ball may get hard under freezing
point. This requires extra force in
detaching and attaching sockets.
Attaching or Removing Bat-
tery Pack
1. To connect the battery pack:
Align the highlighted marker points and
attach battery pack.
Slide the battery pack until it locks into
position.
Alignment
marks
2. To remove the battery pack:
Push the button and slide the battery pack
forward.
Button
-
7
-
III. OPERATION
WARNING!
Do not inhale any smoke emitted from the
tool or battery pack as it may be harmful.
[Main Body]
Switch and Forward/Reverse
Lever Operation
Forward Reverse
Switch lock
CAUTION:
To prevent damage, do not operate
Forward/Reverse lever until the bit
comes to a complete stop.
Forward Rotation Switch
Operation
1. Push the lever for forward rotation.
2. Depress the trigger switch slightly to start
the tool slowly.
3. The speed increases with the amount of
depression of the trigger for efficient tight-
ening of screws. The brake operates and
the bit stops immediately when the trigger
is released.
4. After use, set the lever to its center posi-
tion (switch lock).
Reverse Rotation Switch
Operation
1.
Push the lever for reverse rotation. Check
the
direction of rotation before use.
2.
Depress the trigger switch slightly to start the
tool slowly.
3. After use, set the lever to its center posi-
tion (switch lock).
CAUTION:
To eliminate excessive temperature
increase of the tool surface, do not oper-
ate the tool continuously using two or
more battery packs. Tool needs cool off
time before switching to another pack.
How to Use the Belt Hook
WARNING!
Be sure to attach the belt hook securely
to the main unit with the screw firmly fas-
tened. When the belt hook is not firmly
attached to the main unit, the hook may
disconnect and the main unit may fall.
This may result in an accident or injury.
Periodically check screw for tightness. If
found to be loose, tighten firmly.
Be sure to attach the belt hook firmly and
securely onto a waist belt or other belt. Pay
attention that the unit does not slip off the
belt.
This may result in an accident or injury.
When the main unit is held by the belt
hook, avoid jumping or running with it.
Doing so may cause the hook to slip and
the main unit may fall.
This may result in an accident or injury.
When the belt hook is not used, be sure
to return it to the storing position. The belt
hook may catch on something.
This may result in an accident or injury.
When the unit is hooked onto the waist belt
by the belt hook, do not attach driver bits
to the unit. A sharp edge object, such as a
drill bit, may cause injury or an accident.
To Change the Belt Hook
Location Side
The belt hook can be attached to either
side of the unit.
1. Removing the hook
(1) Remove the nut.
(2) Draw out the hook.
2. Attaching the hook to the other side
(1) Insert the hook in the other side.
(2) Tighten the nut fully so that it
securely fastened.
-
8
-
Variable Speed Control Trigger
To set the center of a hole, pull the trigger
slightly to start the bit rotation slowly.
The more the speed control trigger is
pulled, the higher the speed becomes.
CAUTION:
When operating the tool by pulling the
trigger, there may be a momentary lag
before rotation starts. This does not signal
a malfunction.
This lag occurs as the tool’s circuitry
starts up when the trigger is pulled for
the first time after installing a new bat-
tery pack or after the tool has not been
used for at least 1 minute (or at least 5
minutes when the LED is on). Rotation
will start without any lag during second
and subsequent operations.
Control Panel
(1)
(4) (3)
(2)
(1) Impact Power Mode Select
Selecting the impact power among 3
modes (Soft, Medium, Hard).
Press the impact power mode button to set
it. The mode changes to hard, medium, or
soft each time the button is pressed.
The driver is preset to “hard” impact mode
setting when shipped from the manufac-
turer.
Recommended work guideline table
Impact
Power mode
Display
Recommended Application
H
Jobs requiring a high level
of torque where there is
no possibility of the bolts
or screw breaking, its top
shearing off, or the bit coming
loose. (This setting provides
maximum torque.) Suitable
applications include:
Tightening M8 and larger
bolts
Tightening long screws
during interior finishing work
0 – 2300 r.p.m./
0 – 2500 r.p.m.
and
0 – 3000 i.p.m./
0 – 3500 i.p.m.
M
Jobs requiring limited torque
where there is a possibility of
the screw breaking or its top
shearing off. (This setting limits
torque.) Suitable applications
include:
Tightening bolts with
smaller diameters (M6)
Tightening metalwork
screws when installing
fixtures
0 – 1400 r.p.m.
and
0 – 2800 i.p.m.
S
Jobs requiring limited torque
where there is a possibility
of the screw breaking, its
top shearing off, or the bit
coming loose and damaging
a nished exterior surface.
(This setting limits torque.)
Suitable applications include:
Tightening bolts smaller
than M6 that may shear
easily
Tightening screws into
molded plastic
Installing gypsum wallboard
0 – 1000 r.p.m.
and
0 – 2000 i.p.m.
* i.p.m. = Impact per minute.
Avoid repeatedly depressing the switch
when the bolts and screws are securely
fastened.
Not doing so may cause a delay in
rotation starting, or the Impact Power
mode display to flash and prevent rotation
from starting for circuit protection.
(2) LED light
Pressing the but ton
tog gles the LED light on
and off.
The light illuminates
with very low cur-
rent, and it does not
adversely affect the per-
formance of the driver
during use or its battery
capacity.
CAUTION:
• The built-in LED light is designed to illu-
minate the small work area temporarily.
Do not use it as a substitute for a regu-
lar
flashlight, since it does not have
enough brightness
.
• L
ED light turns off when the tool has not
been used for 5 minutes.
Caution : DO NOT STARE INTO BEAM.
Use of controls or adjustments or performance
of procedures other than those speci ed herein
may result in hazardous radiation exposure.
-
9
-
(3) Overheat warning lamp
Off
(normal
operation)
Illuminated:
Overheat
(motor)
Flashing:
Overheat
(battery)
Indicates operation has
been halted due to motor
or battery overheating.
To protect the motor or battery, be sure to
note the following when carrying out this
operation.
If the motor or battery becomes hot, the
protection function will be activated and
the motor or battery will stop operating.
The overheat warning lamp on the
control panel illuminates or ashes
when this feature is active.
If the overheating protection feature
activates, allow the tool to cool
thoroughly (at least 30 minutes). The
tool is ready for use when the overheat
warning lamp goes out.
Avoid using the tool in a way that
causes the overheating protection
feature to activate repeatedly.
If the tool is operated continuously
under high-load conditions or if it is
used in hot-temperature conditions
(such as during summer), the
overheating protection feature may
activate frequently.
If the tool is used in cold-temperature
conditions (such as during winter) or if
it is frequently stopped during use, the
overheating protection feature may not
activate.
The performance of the EY9L42
deteriorates significantly at and below
10°C due to work conditions and other
factors.
The ambient temperature range is
between 0°C (32°F) and 40°C (104°F).
If the battery pack is used when the
battery temperature is below 0°C
(32°F), the tool may fail to function
properly.
Use the charger at temperatures
between 0°C and 40°C, and charge the
battery at a temperature similar to that
of the battery itself. (There should be no
more than a 15°C difference between
the temperatures of the battery and the
charging location.)
(4) Battery low warning lamp
Off (normal
operation)
Flashing (No charge)
Battery protection
feature active
Excessive (complete) discharging of
lithium ion batteries shortens their service
life dramatically. The driver includes a
battery protection feature designed to
prevent excessive discharging of the
battery pack.
The battery protection feature activates
immediately before the battery loses its
charge, causing the battery low warning
lamp to flash.
If you notice the battery low warning
lamp flashing, charge the battery pack
immediately.
If it is started with too little battery power
remaining, the tool may stop operating
without the battery low warning lamp
flashing first. This indicates that there is
too little battery power remaining to use
the tool, and the battery pack should be
charged before further use.
If the tool is subject to a sudden load
during use that causes the motor to lock
up, the over current prevention sensor
may be triggered, and the impact power
select display may flash. The lamp will
stop flashing once you address the
cause of the motor’s locking up and
cycle the trigger.
Recommended Grip
Use the grip to hold and operate the
driver with one hand. If the job requires
additional force, you can push against
the rear end of the driver with your other
hand.
-
10
-
[Battery Pack]
For Appropriate Use of
Bat tery Pack
Li-ion Battery Pack
For optimum battery life, store the Li-ion bat-
tery pack following use without charging it.
When charging the battery pack, confirm
that the terminals on the battery charger
are free of foreign substances such as
dust and water etc. Clean the terminals
before charging the battery pack if any
foreign substances are found on the
terminals.
The life of the battery pack terminals may
be affected by foreign substances such as
dust and water etc. during operation.
When battery pack is not in use, keep
it away from other metal objects like:
paper clips, coins, keys, nails, screws, or
other small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together
may cause sparks, burns or a fire.
When operating the battery pack, make
sure the work place is well ventilated.
When the battery pack is removed from
the main body of the tool, replace the
battery pack cover immediately in order
to prevent dust or dirt from contaminating
the battery terminals and causing a short
circuit.
Battery Pack Life
The rechargeable batteries have a lim-
ited life. If the operation time becomes
extremely short after recharging, replace
the battery pack with a new one.
Battery Recycling
ATTENTION:
For environmental protection and recy-
cling of materials, be sure that it is dis-
posed of at an officially assigned loca-
tion, if there is one in your country.
Recommendations for use
Terminals
Pack cover
Label
Be sure to use the Pack cover
When the battery pack is not being used,
store the battery in a way that foreign
substances such as dust and water etc.
do not contaminate the terminals. Be sure
to attach the battery pack cover to protect
the battery terminals.
When charging the battery pack, confrm
that the terminals on the battery charger
are free of foreign substances such as
dust and water etc. Clean the terminals
before charging the battery pack if any
foreign substances are found on the
terminals.
The life of the battery pack terminals may
be affected by foreign substances such as
dust and water etc. during operation.
CAUTION:
To protect the motor or battery, be sure to
note the following when carrying out opera-
tion.
• If the motor and battery becomes hot, the
protection function will be activated and
the motor and battery will stop operating.
For safe use
The battery pack is designed to be
installed by proceeding two steps for
safety. Make sure the battery pack is
installed properly to the main unit before
use.
If the battery pack is not connected firmly
when the switch is switched on, the
overheat warning lamp and the battery
low warning lamp will flash to indicate that
safe operation is not possible, and the
main unit will not rotate normally. Connect
the battery pack into the unit of the tool
until the red or yellow label disappears.
-
11
-
How to charge
1. Plug the charger into the AC outlet.
NOTE:
Sparks may be produced when the plug
is inserted into the AC power supply,
but this is not a problem in terms of
safety.
2.
Connect the battery pack firmly into the charger.
1 Line up the alignment marks and place the
battery onto the dock on the charger.
2 Slide forward in the direction of the arrow.
Alignment marks
3.
During charging, the charging lamp will be lit.
When charging is completed, an internal
electronic switch will automatically be trig-
gered to prevent overcharging.
Charging will not start if the battery
pack is warm (for example, immediately
after heavy-duty operation).
The orange standby lamp will be flash-
ing until the battery cools down.
Charging will then begin automatically.
4. The charge lamp (green) will flash slowly
once the battery is approximately 80%
charged.
5.
When charging is completed, the charging
lamp in green color will turn off.
6. If the temperature of the batter pack is
0°C or less, charging takes longer to fully
charge the battery pack than the standard
charging time.
Even when the battery is fully charged, it
will have approximately 50% of the power
of a fully charged battery at normal oper-
ating temperature.
7.
Consult an authorized dealer if the charging
lamp (green) does not turn off.
8. If a fully charged battery pack is inserted
into the charger again, the charging lamp
lights up. After several minutes, the charg-
ing lamp in green color will turn off.
9. Remove the battery pack while the battery
pack release button is held up.
Battery pack
release button
[Battery Charger]
Charging
CAUTION:
The charger is designed to operate on
standard domestic electrical power only
as stated in the rating plate. Charge only
on the voltage indicated on the rating
plate of unit. e.g.230v / 50Hz.
Do not attempt to use it on any other
voltage or frequency rating!
If the temperature of the battery pack
falls approximately below 10°C (14°F),
charging will automatically stop to prevent
degradation of the battery.
The ambient temperature range is
between 0°C (32°F) and 40°C (104°F).
If the battery pack is used when the battery
temperature is below 0°C (32°F), the tool
may fail to function properly.
Use the charger at temperatures between
0°C and 40°C, and charge the battery at
a temperature similar to that of the battery
itself. (There should be no more than a
15°C difference between the temperatures
of the battery and the charging location.)
• When charging a cool battery pack (below
0°C (32°F)) in a warm place, leave the
battery pack at the place and wait for more
than one hour to warm up the battery to
the level of the ambient temperature.
Cool down the charger when charging
more than two battery packs consecutively.
Do not insert your fingers into contact
hole, when holding charger or any other
occasions.
CAUTION:
To prevent the risk of fire or damage to the
battery charger.
Do not cover vent holes on the charger
and the battery pack.
Unplug the charger when not in use.
NOTE:
Your battery pack is not fully charged at
the time of purchase. Be sure to charge
the battery before use.
-
12
-
LAMP INDICATIONS
Charging is completed. (Full charge.)
Battery is approximately 80% charged.
Now charging.
Charger is plugged into the AC outlet. Ready to charge.
(Green) (Orange)
Charging Status Lamp.
Left: green Right: orange will be displayed.
Battery pack is cool.
The battery pack is being charged slowly to reduce the load on the battery.
Battery pack is warm.
Charging will begin when temperature of battery pack drops. If the temperature of the
battery pack is -10° or less, the charging status lamp (orange) will also start flashing .
Charging will begin when the temperature of the battery pack goes up"
Charging is not possible. Clogged with dust or malfunction of the bat-
tery pack.
Turn off Illuminated Flashing
Information for Users on Collection and Disposal of Old Equip-
ment and used Batteries
These symbols on the products, packaging, and/or accompanying docu ments mean
that used electrical and electronic products and batteries should not be mixed with
general household waste.
For proper treatment, recovery and recycling of old products and used bat teries, please
take them to applicable collection points, in accordance with your national legislation
and the Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inap propriate waste handling.
For more information about collection and recycling of old products and bat teries,
please contact your local municipality, your waste disposal service or the point of sale
where you purchased the items.
Penalties may be applicable for incorrect disposal of this waste, in ac cordance with
national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or
supplier for further information.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items,
please contact your local authorities or dealer and ask for the correct method of disposal.
-
13
-
IV. MAINTENANCE
Use only a dry, soft cloth for wiping the unit.
Do not use a damp cloth, thinner, benzine,
or other volatile solvents for cleaning.
In the event that the inside of the tool or
battery pack is exposed to water, drain
and allow to dry as soon as possible.
Carefully remove any dust or iron filings
that collect inside the tool. If you experi-
ence any problems operating the tool,
consult with a repair shop.
V. TIGHTENING
TORQUE
The power required for tightening a bolt will
vary, according to bolt material and size, as
well as the material being bolted. Choose
the length of tightening time accordingly.
Reference values are provided below.
(They may vary according to tightening conditions.)
Factors Affecting Tighten-
ing Torque
The tightening torque is affected by a wide
variety of factors including the followings.
After tightening, always check the torque
with a torque wrench.
1) Voltage
When the battery pack becomes near-
ly discharged, the voltage decreases and
the tightening torque drops.
Bolt Tightening Conditions
EY75A1 14.4 V
M10 x 35 mm M12, M14, M16 x 45 mm
Standard bolt
N × m
(kgf-cm)
Tightening torque
Tightening time (Sec.)
EY75A1 14.4 V
M8, M10 x 35 mm. M12 x 45 mm
High tensile bolt
N × m
(kgf-cm)
Tightening torque
Tightening time (Sec.)
EY75A2 14.4 V
M10 x 35 mm M12, M14, M16 x 45 mm
Standard bolt
N s m
(kgf-cm)
Tightening torque
Tightening time (Sec.)
-
14
-
EY75A2 18 V
M10 x 35 mm M12, M14, M16 x 45 mm
Standard bolt
N s m
(kgf-cm)
Tightening torque
Tightening time (Sec.)
EY75A2 18 V
M8, M10 x 35 mm. M12 x 45 mm
High tensile bolt
N s m
(kgf-cm)
Tightening torque
Tightening time (Sec.)
Bolt
Nut
Washer
Steel plate
thickness 10 mm
Washer
Spring washer
Tightening conditions
The following bolts are used.
Standard bolts: Strength type 4.8
High tensile type 12.9
4.8
Explanation of the strength type
Bolt yield point
(
80% of tensile strength)
32 kgf/mm
2
(45000 psi)
Bolt tensile strength
40 kgf/mm
2
(56000 psi)
EY75A2 14.4 V
M8, M10 x 35 mm. M12 x 45 mm
High tensile bolt
N s m
(kgf-cm)
Tightening torque
Tightening time (Sec.)
EY75A1 18 V
M10 x 35 mm M12, M14, M16 x 45 mm
Standard bolt
N × m
(kgf-cm)
Tightening torque
Tightening time (Sec.)
EY75A1 18 V
M8, M10 x 35 mm. M12 x 45 mm
High tensile bolt
N × m
(kgf-cm)
Tightening torque
Tightening time (Sec.)
-
15
-
VI. ACCESSORIES
Use only suitable size of bit.
Panasonic original Optional Quick change chuck (EY9HX110E or EY9HX111E).
Chuck Size: 6.35 mm hex
EY9HX111EEY9HX110E
2) Tightening time
Longer tightening time results in increased
tightening torque. Excessive tightening,
how ever, adds no value and reduces the
life of the tool.
3) Different bolt diameters
The size of the bolt diameter affects the
tight ening torque.
Generally, as the bolt diameter increases,
tightening torque rises.
4) Tightening conditions
Tightening torque will vary, even with the
same bolt, according to grade, length, and
torque coefficient (the fixed coefficient indi-
cated by the manufacturer upon produc-
tion).
Tightening torque will vary, even with
the same bolting material (e.g. steel),
accord ing to the surface finish.
Torque is greatly reduced when the bolt
and nut start turning together.
5) Socket play
Torque is lowered as the six-sided
configu ration of the socket of the wrong
size is used to tighten a bolt.
6) Switch (Variable speed control trigger)
Torque is lowered if the unit is used with
the switch not fully depressed.
7) Effect of Connecting Adaptor
The tightening torque will be lowered
through the use of a universal joint or a
connecting adaptor.
-
16
-
VII. APPENDIX
MAXIMUM RECOMMENDED CAPACITIES
Model
EY75A1 EY75A2
Screw driving
Wood screw
3.5 mm - 9.5 mm
Self-drilling screw
3.5 mm - 6 mm
Bolt fastening
Standard bolt : M6 - M16
High tensile bolt
: M6 - M12
WARRANTY SUPPLEMENT
The breakdown and damage caused by usage consistent for a long time (e.g.: factory work on
the assembly line, etc.) is out of warranty.
VIII. SPECIFICATIONS
NOTE:
Weight indication
Greater than or equal to 1kg : indicated by 0.05kg.
Less than 1kg : indicated by 0.01kg.
MAIN UNIT
Model
EY75A1 EY75A2
Motor voltage 14.4 V DC 18 V DC 14.4 V DC 18 V DC
No load speed
soft mode 0 - 1000 min
-1
medium mode 0 - 1400 min
-1
hard mode 0 - 2500 min
-1
0 - 2300 min
-1
Maximum torque 150 N·m 155 N·m 200 N·m 205 N·m
Impact per minute
soft mode 0 - 2000 min
-1
medium mode 0 - 2800 min
-1
hard mode 0 - 3000 min
-1
0 - 3500 min
-1
Overall length 143 mm 155 mm
Weight
(with battery pack: EY9L44)
1.55 kg
-
1.55 kg
-
Weight
(with battery pack: EY9L45)
1.55 kg
-
1.55 kg
-
Weight
(with battery pack: EY9L50)
-
1.65 kg
-
1.65 kg
Weight
(with battery pack: EY9L51)
-
1.65 kg
-
1.65 kg
Noise,Vibration See the included sheet
-
17
-
BATTERY PACK
Model EY9L41 EY9L42 EY9L44 EY9L45 EY9L50 EY9L51
Storage battery Li-ion Battery
Battery voltage
14.4 V DC
(3.6 V x 4 cells)
14.4 V DC
(3.6 V x 8 cells)
18 V DC
(3.6 V x 10 cells)
BATTERY CHARGER
Model EY0L81
Electrical rating See the rating plate on the bottom of the charger
Weight
0.93 kg
Charging time
EY9L41 EY9L42 EY9L44 EY9L45 EY9L50 EY9L51
Usable:
45 min
Usable:
30 min
Usable:
50 min
Usable:
65 min
Usable:
50 min
Usable:
65 min
Full:
60 min
Full:
35 min
Full:
65 min
Full:
80 min
Full:
65 min
Full:
80 min
Model EY0L82
Electrical rating See the rating plate on the bottom of the charger
Weight
0.93 kg
Charging time
EY9L41 EY9L42 EY9L44 EY9L45 EY9L50 EY9L51
Usable:
35 min
Usable:
30 min
Usable:
40 min
Usable:
50 min
Usable:
40 min
Usable:
55 min
Full:
50 min
Full:
35 min
Full:
55 min
Full:
60 min
Full:
55 min
Full:
70 min
NOTE: This chart may include models that are not available in your area.
Please refer to the latest general catalogue.
NOTE: For the dealer name and address, please see the included warranty card.
-
18
-
IMPORTANT:
The wires in this mains lead are
coloured in accordance with the follow-
ing code:
Blue: Neutral
Brown: Live
As the colours of the wire in the mains lead
of this appliance may not correspond with
the coloured markings identifying the termi-
nals in your plug, proceed as follows.
The wire which is coloured BLUE must be
connected to the terminal in the plug which
is marked with the letter N or coloured
BLACK.
The wire which is coloured BROWN must be
connected to the terminal in the plug which is
marked with the letter L or coloured RED.
Under no circumstances should either of
these wires be connected to the earth ter-
minal of the three pin plug, marked with the
letter E or the Earth Symbol
.
How to replace the fuse: Open the fuse
compartment with a screwdriver and replace
the fuse and fuse cover if it is removable.
Fuse Cover
This apparatus was produced to BS800.
ONLY FOR U. K.
IX. ELECTRICAL
PLUG
INFORMATION
FOR YOUR SAFETY PLEASE READ
THE FOLLOWING TEXT CAREFULLY
This appliance is supplied with a moulded
three pin mains plug for your safety and
convenience.
A 5 amp fuse is tted in this plug.
Should the fuse need to be replaced please
ensure that the replacement fuse has a rat-
ing of 5 amp and that it is approved by ASTA
or BSI to BS1362.
Check for the ASTA mark
or the BSI mark
on the body of the fuse.
If the plug contains a removable fuse cover
you must ensure that it is re tted when the
fuse is replaced.
If you lose the fuse cover the plug must
not be used until a replacement cover is
obtained.
A replacement fuse cover can be purchased
from your local Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UN-
SUITABLE FOR THE SOCKET OUTLET IN
YOUR HOME THEN THE FUSE SHOULD
BE REMOVED AND THE PLUG CUT OFF
AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE
ELECTRICAL SHOCK IF THE CUT OFF
PLUG IS INSERTED INTO ANY 13 AMP
SOCKET.
If a new plug is to be tted please observe
the wiring code as shown below.
If in any doubt please consult a quali ed
electrician.
-
19
-
I. WEITERE WICHTIGE
SICHERHEITSREGELN
1)
Geeigneten Gehörschutz tragen, wenn
das Werkzeug längere Zeit im Betrieb ist!
2)
Denken Sie daran, dass das Werk zeug
ständig betriebsbereit ist, da es nicht an die
Steckdose angeschlossen werden muss.
3) Beim Schrauben in Wände, Fußböden
usw. können stromführende Kabel
be rührt werden. DAHER NIE DAS VIER-
KANTSCHNELLSPANNFUTTER ODER
ANDERE VORDERE METALLTEILE
BERÜHREN! Das Werkzeug beim
Schrauben nur am Kunststoffgriff halten,
um in solchen Fällen vor elektrischen
Schlägen geschützt zu sein.
4)
Betätigen Sie den Rechts-/Linkslauf-
Umschalthebel NICHT, wenn der Haupts chalter
eingeschaltet ist. Der Akku entlädt sich sonst
schnell, und das Gerät kann beschädigt werden.
5) Beim Aufladen kann sich das Lade gerät
etwas erhitzen. Dies ist normal.
Den Akku daher NICHT über lange Zeit aufladen.
6)
Stellen Sie den Rechts-/Linkslauf- Umschalthe-
bel zum Lagern oder Tragen des Werkzeugs
auf die Mittenstellung (Schaltersperre).
7) Belasten Sie das Werkzeug nicht, indem
Sie den Elektronikschalter halb gedrückt
halten (Drehzahlregelmodus), sodass der
Motor stehen bleibt.
Symbol Bedeutung
V Volt
Gleichstrom
n
0
Leerlaufdrehzahl
… min
-1
Drehzahl oder Hubzahl pro
Minute
Ah
Akkukapazitat in Ampere
Stunden
Lesen Sie die
Bedienungsanleitung vor
Gebrauch.
Nur für Inneneinsatz.
WARNUNG:
Verwenden Sie nur die Panasonic-Akkus, die für den
Einsatz mit dieser Akku-Maschine ausgelegt sind.
Panasonic übernimmt keine Verantwortung
für etwaige Schäden oder Unfälle, die
durch den Gebrauch von recycelten oder
gefälschten Akkus verursacht werden.
Werfen Sie den Akku nicht ins Feuer, und setzen
Sie ihn auch keiner übermäßigen Wärme aus.
Unterlassen Sie das Einschlagen von Nägeln
in den Akku sowie Erschüttern, Zerlegen
oder Abändern des Akkus.
Achten Sie darauf, dass keine
Metallgegenstände mit den Kontakten des
Akkus in Berührung kommen.
Unterlassen Sie das Tragen oder
Aufbewahren des Akkus zusammen mit
Nägeln oder ähnlichen Metallgegenständen
im selben Behälter.
Original-Anleitung: Englisch
Übersetzung der Original-Anleitung:
Andere Sprachen
Lesen Sie bitte vor der ersten Inbetriebnah-
me dieses Gerätes das separate Handbuch
„Sicherheitsmaßregeln“ sorgfältig durch.
-
20
-
Laden Sie den Akku nicht an einem heißen Ort,
wie z. B. in der Nähe eines Feuers oder in direk-
tem Sonnenlicht. Anderenfalls kann der Akku
überhitzen, Feuer fangen oder explodieren.
Verwenden Sie nur das zugehörige Lade gerät
zum Laden des Akkus. Anderenfalls kann der
Akku auslaufen, überhitzen oder explodieren.
Nachdem Sie den Akku von der Maschine
oder dem Ladegerät abgenommen haben,
bringen Sie stets die Akkuabdeckung
wieder an. Anderenfalls könnten die
Akkukontakte kurzgeschlossen werden,
was zu einem Brand führen kann.
Wenn der Akku schwach geworden ist,
ersetzen Sie ihn durch einen neuen.
Fortgesetzter Gebrauch eines beschä-
digten Akkus kann zu Wärmeerzeugung,
Entzündung oder Bruch führen.
II. BAUGRUPPE
Anbringen oder Abnehmen
des Bits
HINWEIS:
Trennen Sie vor dem Anbringen oder Abneh-
men eines Bits den Akku vom Werkzeug ab,
oder stellen Sie den Elektroniks chalter auf
die Mittel stellung (Schaltersperre).
1. Die Hülse des Schnellspannfutters halten
und vom Schrauber herausziehen.
2. Den Bit in das Bohrfutter einsetzen. Die
Hülse loslassen.
3. Der Ring springt in seine Ausgangs po sition
zurück, wenn er losgelassen wird.
4.
An dem Bit ziehen, um sicherzustellen, das er
nicht abgezogen werden kann.
5. Zum Entfernen des Bits die Hülse auf die
gleiche Weise herausziehen.
VORSICHT:
Wenn der Ring nicht in seine Ausgangs-
position zurückkehrt oder wenn sich der
Bit löst, wenn an ihm gezogen wird, wurde
der Bit nicht ordnungsgemäß eingesetzt.
Vor der Inbetriebnahme sicher stellen,
dass der Bit ordnungsgemäß befestigt ist.
Verwenden Sie 6,35-mm Sechskant bits.
Um einwandfreie Sicherung des Bits zu
gewährleisten, verwenden Sie nur Sechs-
kantbits mit 9,5 mm Arretierung.
6.35 mm
9.5 mm
Anbringen oder Abnehmen
einer Stecknuss
1. Anbringen einer Stecknuss
Bringen Sie die Stecknuss an, indem Sie die
Fassung an der Unterseite der Stecknuss
auf den Vierkant am Werkzeug schieben.
Vergewissern
Sie sich, dass
die Stecknuss
fest mit dem
Werkzeug ver-
bunden ist.
2. Abnehmen einer Stecknuss
Ziehen Sie die Stecknuss ab.
HINWEIS:
Anbringen oder Abnehmen von
Originalzubehör und Stecknüssen
Halten Sie das Werkzeug über dem
Gefrierpunkt (0°C), wenn Sie Originalzubehör
und Stecknüsse am Vierkant des Werkzeugs
anbringen oder davon abnehmen. Das Gummi-
kissen im Vierkant, das die Kugel hochdrückt,
kann unterhalb des Gefrierpunkts hart werden.
Dies erfordert zusätzliche Kraft beim Abnehmen
und Anbringen von Stecknüssen.
Anbringen oder Abnehmen
des Akkus
1. Zum Anschließen des Akkus:
Die Ausrichtmarkierungen aufeinander
ausrichten, und den Akku anbringen.
Den Akku einschieben, bis er einrastet.
Ausrichtmarkierungen
2. Zum Entfernen des Akkus:
Den Knopf drücken und den Akku
einschieben.
Knopf
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136

Panasonic EY75A1 Operating Instructions Manual

Taper
Operating Instructions Manual
Ce manuel convient également à

dans d''autres langues