Hikoki CB3612DA Manuel utilisateur

Model

Modèle

Modelo

CB 3612DA

Cordless Band Saw

Scie à ruban sans-ﬁ l

Sierra de cinta inalámbrica

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool. This manual should be

stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.

Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce

mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent

l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este

manual debe ser guardado en un lugar seguro.

Designed for operating in USA & Canada only.

When this product is used in areas other than the USA & Canada,

we cannot guarantee the product quality and performance.

2

English

IMPORTANT SAFETY INSTRUCTIONS

Read all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or

maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety

rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,

and by observing appropriate safety procedures.

Basic safety precautions are outlined in the "SAFETY" section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identiﬁ ed by WARNINGS on the power

tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been speciﬁ cally recommended by metabo HPT.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or

may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk

of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

3

English

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ -position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your ﬁ nger on the switch

or energising power tools that have the switch on

invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts.

Loose clothes, jewellery or long hair can be caught

in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of dust collection can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the risk

of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may aﬀ ect the

power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier

to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations diﬀ erent

from those intended could result in a hazardous

situation.

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by

the manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of ﬁ re when used with

another battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂ ush with water.

If liquid contacts eyes, additionally seek

medical help.

Liquid ejected from the battery may cause irritation

or burns.

6) Service

a) Have your power tool serviced by a

quali

ﬁ ed repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is

maintained.

–WARNING–

To reduce the risk of injury, user must read

instruction manual.

4

English

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring.

Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and could

give the operator an electric shock.

2. Securely fasten the workpiece to be cut.

If the workpiece is not securely fastened, it may shift

position and cause damage to the band saw blade

and/or injury.

3. ALWAYS wear ear protectors when using the tool

for extended periods.

Prolonged exposure to high intensity noise

can cause hearing loss.

4. NEVER touch the band saw blade with bare hands

after operation.

5. Because the cordless band saw operates by battery

power, be aware of the fact it can begin to operate at

any time.

6. When working at elevated locations, clear the area

of all other people and be aware of conditions below

you.

7. NEVER touch rotating parts.

NEVER place your hands, ﬁ ngers or other

body parts near the tool’s rotating parts.

8. NEVER operate without all guards in place.

NEVER operate this tool without all guards or safety

features in place and in proper working order. If

maintenance or servicing requires the removal of a

guard or safety feature, be sure to replace the guard

or safety feature before resuming operation of the

tool.

9. Use right tool.

Don’t force small tool or attachment to do the job of a

heavy-duty tool.

Don’t use tool for purpose not intended —for

example— don’t use band saw for cutting tree limbs

or logs.

10. NEVER use a power tool for applications other

than those speciﬁ ed.

NEVER use a power tool for applications other than

those speciﬁ ed in the Instruction Manual.

11. Handle tool correctly.

Operate the tool according to the instructions

provided herein. Do not drop or throw the tool.

NEVER allow the tool to be operated by children,

individuals unfamiliar with its operation or

unauthorized personnel.

12. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

13. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

14. Band saw blade and accessories must be

securely mounted to the tool.

Prevent potential injuries to yourself or others. Band

saw blade and accessories which have been mounted

to the tool should be secure and tight.

15. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that

air can freely ﬂ ow at all times. Check for dust build-up

frequently.

16. NEVER use a tool which is defective or operating

abnormally.

If the tool appears to be operating unusually, making

strange noises, or otherwise appears defective, stop

using it immediately and arrange for repairs by a

metabo HPT authorized service center.

17. NEVER leave tool running unattended. Turn

power oﬀ .

Don’t leave tool until it comes to a complete stop.

18. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

19. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened

with soapy water and dry thoroughly.

20. ALWAYS wear eye protection that meets the

requirement of the latest revision of ANSI

Standard Z87.1.

21. ALWAYS wear a mask or respirator to protect yourself

from dust or potentially harmful particles generated

during operation.

22. ALWAYS ﬁ rmly grip the handle while operating.

23. ALWAYS be careful with buried object such as an

underground wiring.

Touching these active wiring or electric cable with this

tool, you may receive an electric shock.

Conﬁ rm if there are any buried object such as electric

cable within the wall, ﬂ oor or ceiling where you are

going to operate here after.

5

English

24. Do not use the product if the tool or the battery

terminals (battery mount) are deformed.

Installing the battery could cause a short circuit that

could result in smoke emission or ignition.

25. Keep the tool’s terminals (battery mount) free of swarf

and dust.

○

Prior to use, make sure that swarf and dust have not

collected in the area of the terminals.

○

During use, try to avoid swarf or dust on the tool from

falling on the battery.

○

When suspending operation or after use, do not leave

the tool in an area where it may be exposed to falling

swarf or dust.

Doing so could cause a short circuit that could result

in smoke emission or ignition.

26. Deﬁ nitions for symbols used on this tool

V ..............volts

—

---

............direct current

SFPM.......surface feet

no ............no load speed

ADDITIONAL SAFETY WARNINGS

1. Always hold the tool ﬁ rmly with both hands on handle

and front handle (Fig. 1). Do not touch the metal part.

Front

handle

Handle

Fig. 1

2. Make sure that the area to be cut is absolutely free

of any hidden obstructions including electrical wiring,

water, or gas pipes. Cutting into the aforementioned

may result in electric shock or short circuit, gas leak

or other hazards that can cause serious accidents or

injuries.

3. Make sure to securely hold the tool during operation.

Failure to do so can result in accidents or injuries.

4. Setting up and checking the work environment.

Check if the work environment is suitable by following

the precaution.

5. Dust particles such as silica or asbestos are

hazardous to your health. When working with

materials containing these components, take

appropriate dust-prooﬁ ng measures.

6. Working with metal can cause sparks. Make sure

there are no ﬂ ammable and combustible materials in

the vicinity and that they are stored in a safe location.

7. During operation, do not put your hands, face, or other

body parts near the rotating band saw blade or other

rotating parts. Doing so may result in injury.

8. If the main unit is accidentally dropped or suﬀ ers any

impact, carefully inspect the band saw blade, the

unit, etc. to be sure there are no damages, cracks, or

deformations.

Injury may result if there are any damages, cracks, or

deformations.

9. During operation, if the unit is not running smoothly,

or there are abnormal sounds or vibrations, promptly

switch oﬀ the unit, discontinue use and contact a

metabo HPT Authorized Service Center for inspection

and/or repairs.

Continuing use under these conditions may result in

injury.

10. When using this unit continuously, the unit may

overheat, leading to damage in the motor and switch.

Please leave it without using it for approximately

15 minutes.

11. Follow the instruction manual and make sure that

the band saw blade and accessories are properly

installed.

Improper installation may result in injury from parts

coming loose.

12. Securely fasten the workpiece to be cut.

If the workpiece is not securely fastened, it may shift

position and cause damage to the band saw blade

and/or injury.

13. To avoid having the band saw blade clamped

between the cut surfaces during or immediately after

cutting, set up a support stand to bear the weight of

the workpiece, placing it near the section to be cut.

If the band saw blade becomes clamped, it may result

in injury.

14. If the section to be cut oﬀ is large, set up another

stable support stand to bear the weight of that section

as well.

Not using such a support may result in injury.

15. During operation, do not wear cloth work gloves or

other similar hand protection that may get caught in

the unit.

Getting caught in the rotating section of the tool may

result in injury.

16. Prior to operation, verify the safety of the surrounding

area and run the blade brieﬂ y to make sure that there

are no abnormalities in the vibrations of the unit or in

the band saw blade.

If there are such abnormalities, unexpected

movements may occur and cause injury.

6

English

17. When working in a high location, ensure that there are

no people below.

Dropping the workpiece or the cordless tool from a

high location may result in an accident.

18. Do not apply any sudden impact to the workpiece with

the band saw blade.

Doing so may damage the band saw blade and/or

result in injury.

19. Use the product’s own weight or press gently to cut a

workpiece.

Applying unnecessary force while cutting can result

in detachment of or damage to the band saw blade

which may cause injury.

20. Do not touch the band saw blade, the workpiece, or

shavings with bare hands immediately after cutting,

as they will be hot.

Doing so may result in burns.

21. Remove any shavings adhering to the band saw blade

or blade pulley rubbers as well as any shavings that

accumulates inside the pulley guard (A), (B).

The shavings may cause the band saw blade to

detach or slip, and result in injury.

22. If the switch lock won’t return to its original position,

promptly discontinue use and contact a metabo HPT

Authorized Service Center for repairs.

23. Use of a band saw blade other than one authorized

by the manufacture or a band saw blade with any

abnormalities may result in damage to the band saw

blade and/or injury.

24. When switching the power on, verify that the band

saw blade is not in contact with the workpiece to be

cut or any surrounding objects.

Failure to do so may result in the main unit being

dropped and/or injury.

25. In order to prevent accidents, when taking a break

from operation or after operation, be sure to switch oﬀ

the power and remove the battery from the cordless

tool.

26. If the band saw blade locks up while cutting, promptly

switch oﬀ the power and stop it from running.

Failure to do so may result in damage to the band saw

blade.

27. The motor may stop in the event the tool is overloaded.

In this should occur, release the tool’s switch and

eliminate the cause of the overload.

28. Do not leave the tool running unattended on the ﬂ oor,

table or other locations. Doing so may result in injury.

29. For cutting eﬃ ciency, switch the mode of the

application tool according to task conditions and

workpieces to be cut.

30. Do not use two or more batteries continuously.

Doing so will not only pose a problem to the unit body,

but may also cause the temperature of the unit body

to rise, or lead to burn injuries.

31. After use, be sure not to place the tool near chips or

sawdust before it comes to a full stop as the tool may

suck in those particles.

32. After use, if the unit will not be used for a long period,

remove the band saw blade from the unit body and

store the band saw blade.

If the band saw blade is left installed in the unit body

for a long period, the lifespan of the band saw blade

will become shorter.

IMPORTANT SAFETY INSTRUCTIONS FOR

CHARGER OR ADAPTER

The term “charger or adapter” in the safety instructions

refers to your battery charger or AC/DC adapter.

WARNING

Death or serious bodily injury could result from

improper or unsafe use of charger or adapter.

To avoid these risks, follow these basic safety

instructions:

READ ALL INSTRUCTIONS

1. This manual contains important safety and operating

instructions for battery charger Model UC18YSL3 or

AC/DC adapter Model ET36A.

2. Before using charger or adapter, read all instructions

and cautionary markings on (1) charger or adapter, (2)

battery, and (3) product using battery.

3. When charging the battery with a battery charger,

reduce the risk of injury by charging metabo HPT

rechargeable battery multi volt type series and BSL18

series. Other type of batteries may burst causing

personal injury and damage.

4. Do not expose charger or adapter to rain or snow.

5. Use of an attachment not recommended or sold by

the charger or adapter manufacturer may result in a

risk of ﬁ re, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord,

pull by plug when disconnecting charger or adapter.

7. Make sure cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

8. An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of ﬁ re and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same

number, size, and shape as those of plug on

charger or adapter:

b. That extension cord is properly wired and in good

electrical condition; and

c. That wire size is large enough for AC ampere

rating of charger or adapter as speciﬁ ed in Table 1.

7

English

WARNING

Improper use of the battery or battery charger

can lead to serious injury. To avoid these injuries:

1. NEVER disassemble the battery or AC/DC adapter.

2. NEVER incinerate the battery or AC/DC adapter, even

if it is damaged or is completely worn out. The battery

can explode in a ﬁ re.

3. NEVER short-circuit the battery or AC/DC adapter.

4. NEVER insert any objects into the charger or

adapter’s air vents. Electric shock or damage to the

charger or adapter may result.

5. NEVER use outdoors. Keep the battery or AC/DC

adapter away from direct sunlight and use only where

there is low humidity and good ventilation.

6. NEVER charge when the temperature is below 14°F

(-10°C) or above 104°F (40°C). (UC18YSL3)

NEVER use when the temperature is below 14°F

(-10°C) or above 104°F (40°C). (ET36A)

7. NEVER connect two charger or adapter together.

8. NEVER insert foreign objects into the hole for the

battery or the charger or adapter.

9. NEVER use a booster transformer.

10. NEVER use DC power.

11. NEVER store the battery or charger or adapter in

places where the temperature may reach or exceed

104°F (40°C) such as inside metal box or car.

12. NEVER expose the battery or charger or adapter to

rain or wet conditions.

13. ALWAYS operate charger or adapter on standard

household electrical power (120 volts). Using the

charger or adapter on any other voltage may overheat

and damage the charger.

14. ALWAYS wait at least 15 minutes between charges to

avoid overheating the charger. (UC18YSL3)

15. ALWAYS disconnect the power cord from its

receptacle when the charger or adapter is not in use.

[The information below applies only to ET36A]

16. Do not use the product if the tool or the AC/DC adapter

terminals (AC/DC adapter mount) are deformed.

Installing the AC/DC adapter could cause a short

circuit that could result in smoke emission or ignition.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR CHARGER OR ADAPTER

AC Input Rating Amperes* AWG Size of Cord

Equal to or

greater than

but less

than

Length of Cord, Feet (Meter)

25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

* If the input rating of a charger or adapter is given in

watts rather than in amperes, the corresponding

ampere rating is to be determined by dividing the

wattage rating by the voltage rating–for example:

1250 watts

= 10 amperes

125 volts

9. Do not operate charger or adapter with damaged cord

or plug-replace them immediately.

10. Do not operate charger or adapter if it has received a

sharp blow, been dropped, or otherwise damaged in

any way; take it to a qualiﬁ ed serviceman.

11. Do not disassemble charger or adapter; take it to

a qualiﬁ ed serviceman when service or repair is

required. Incorrect reassembly may result in a risk of

electric shock or ﬁ re.

12. To reduce risk of electric shock, unplug charger

or adapter from receptacle before attempting any

maintenance or cleaning. Removing the battery will

not reduce this risk.

13. This AC/DC adapter is for use only with speciﬁ c tools,

including CB3612DA. The adapter might be suitable

for use with other metabo HPT battery operated tools.

It is necessary to conﬁ rm suitability by referencing the

instruction manual of the speciﬁ c tool or by consulting

our web site https://www.metabo-hpt.com/. Failure

to conﬁ rm suitability before using the adapter with

speciﬁ c tools could result in ﬁ re hazard.

IMPORTANT SAFETY INSTRUCTIONS FOR

USE OF THE BATTERY AND CHARGER OR

ADAPTER

You must charge the battery before you can use the power

tool. Before using the model UC18YSL3 battery charger,

be sure to read all instructions and cautionary statements

on it, the battery and in this manual.

CAUTION

USE ONLY metabo HPT BATTERY TYPE

BSL36B18. OTHER TYPES OF BATTERIES MAY

BURST AND CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

8

English

6. During use, if the machine stops running after the

Box’s LED lamp blinks, conﬁ rm the power supply

environment.

7. Do not drag the cord when using or carrying the

machine.

Doing so may tear the cord insulation or break the

cord which could result in electric shock.

8. Do not stretch the cord out any more than required.

When using tools such as gardening clippers or

circular saws, always make sure of the power cord’s

position to avoid cutting the cord during operation.

9. To use the AC/DC adapter after it shuts down due to

high temperature, disconnect the box’s power plug,

wait for the LED lamp to go out and then reconnect

the box’s power plug.

If the machine cuts oﬀ even after suﬃ ciently cooling it

oﬀ with the built-in fan, discontinue use as there may

be a problem with the machine.

10. Do not use this product near a radio. Doing so could

cause noise from the radio, making it diﬃ cult to listen

to a broadcast.

11. This is a power source for multi volt products. Do not

use with 18 V products or chargers. Doing so could

result in damage.

12. Overload behavior may diﬀ er when compared with

BSL36B18 battery use.

With the battery where the LED should blink on the

main unit, the LED on the AC/DC adapter may blink

instead.

PRECAUTIONS FOR AC/DC ADAPTER

The adapter equips with the protection function to stop the

output. In the cases of 1 to 2 described below, when using

this product, even if you are pulling the switch, the motor

may stop. This is not the trouble but the result of protection

function.

1. If the tool is overloaded, output may stop. In this case,

release the switch of tool and eliminate causes of

overloading.

2. If the adapter is overheated under overload work,

output may stop. In situations like this, discontinue

use of the adapter and detach it from the tool. Allow

the adapter to cool in a location such as a shaded area

with good air circulation.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with

the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

17. Keep the tool’s terminals (AC/DC adapter mount) free

of swarf and dust.

○

Prior to use, make sure that swarf and dust have not

collected in the area of the terminals.

○

During use, try to avoid swarf or dust on the tool from

falling on the AC/DC adapter.

○

When suspending operation or after use, do not leave

the tool in an area where it may be exposed to falling

swarf or dust.

Doing so could cause a short circuit that could result

in smoke emission or ignition.

18. The product is intended for Use in Pollution Degree

2 or PD2 environments. Operate only in areas of

non-conductive pollution. A temporary conductivity

caused by condensation is normally expected.

19. This is a precision machine so do not drop or expose

to impact.

20. Do not use this product near a pacemaker or other

similar implanted device, which may be aﬀ ected by a

magnetic ﬁ eld produced by this product.

21. The adapter, power supply box and the inside of the

DC cord generates a boosted high voltage of 380 V so

please be careful of the following.

○

Do not disassemble the product.

○

Do not drop or expose to impact.

In the event the product is damaged from strong

impact, do not use the product.

○

Do not use the product in areas exposed to rain,

snow, iron powder or wet condition.

○

Do not touch the product with wet hands.

○

Do not spill or pour liquid onto the product.

○

Do not pull the cord with excessive force.

○

Use the product in a well-ordered work environment.

CAUTION

1. When the mesh of the vent is plugged by objects such

as wood shavings, try to keep the objects out when

you clear the mesh.

(If not properly maintained, the temperature protective

feature could shut the product oﬀ )

2. When the temperature protective feature frequently

cuts the power oﬀ , do not overload the machine with

continued work, but let the machine rest for a little

before continuing operation.

3. The machine does get hot. However, this does not

indicate an abnormality.

Keep the electricity running and operate the internal

fan to cool the machine before carrying it elsewhere.

When carrying the product, make sure to use the cord

armor. The case may be hot so please be careful.

4. During use, do not pull the cord to move the Box.

Doing so may result in damage.

5. Do not use more that a single cord reel of 30 meters.

Doing so may result in damage.

9

English

1. When the battery power remaining runs out, the motor

stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes

of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○

During work make sure that swarf and dust do not fall

on the battery.

○

Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○

Do not store an unused battery in a location exposed

to swarf and dust.

○

Before storing a battery, remove any swarf and dust

that may adhere to it and do not store it together with

metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject

the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or car

cigarette lighter sockets.

6. Do not use the battery for a purpose other than those

speciﬁ ed.

7. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately

stop further recharging.

8. Do not put or subject the battery to high temperatures

or high pressure such as into a microwave oven,

dryer, or high pressure container.

9. Keep away from ﬁ re immediately when leakage or foul

odor are detected.

10. Do not use in a location where strong static electricity

generates.

11. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears

abnormal during use, recharging or storage,

immediately remove it from the equipment or battery

charger, and stop use.

12. Do not immerse the battery or allow any ﬂ uids to ﬂ ow

inside. Conductive liquid ingress, such as water, can

cause damage resulting in ﬁ re or explosion. Store your

battery in a cool, dry place, away from combustible

and ﬂ ammable items. Corrosive gas atmospheres

must be avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁ nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the ﬁ rst time, do not use and return it to

your supplier or vendor.

WARNING

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of ﬁ re. Please observe the

following matters when storing the battery.

○

Do not place electrically conductive cuttings,

nails, steel wire, copper wire or other wire in the

storage case.

○

Either install the battery in the power tool or store

by securely pressing into the battery cover until

the ventilation holes are concealed to prevent

short-circuits (See Fig. 4).

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe

the following precautions.

WARNING

Notify the transporting company that a package

contains a lithium-ion battery, inform the company

of its power output and follow the instructions of the

transportation company when arranging transport.

●

Lithium-ion batteries that exceed a power output

of 100 Wh are considered to be in the freight

classiﬁ cation of Dangerous Goods and will

require special application procedures.

●

For transportation abroad, you must comply with

international law and the rules and regulations of

the destination country.

●

If the BSL36B18 is installed in the power tool,

the power output will exceed 100 Wh and the unit

will be classiﬁ ed as Dangerous Goods for freight

classiﬁ cation.

10

English

Wh

Power Output

2 to 3 digit number

Fig. 2

USB DEVICE CONNECTION

PRECAUTIONS

When an unexpected problem occurs, the data in a USB

device connected to this product may be corrupted or lost.

Always make sure to back up any data contained in the

USB device prior to use with this product.

Please be aware that our company accepts absolutely no

responsibility for any data stored in a USB device that is

corrupted or lost, nor for any damage that may occur to a

connected device.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

11

English

FUNCTIONAL DESCRIPTION

NOTE

The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance

of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have ﬁ rst read and understood all safety

instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that diﬀ er from those on your own

power tool.

NAME OF PARTS

1. Cordless Band Saw (CB3612DA)

Battery

Motor (built-in)

Housing

Switch lock

Switch

Handle

Duster plate

Guide plate

Band saw blade

Tension lever

Pulley

guard (B)

Dial for setting

band saw blade

circumferential

speed

Front

handle

Name plate

LED light

Blade

pulley (A)

Guide rollers

Blade

pulley (B)

Pulley

guard (C)

Hook

Pulley

guard (A)

Fig. 3

2. Battery 3. Battery Charger

Ventilation holes

Latch

Terminals

Battery cover

Battery

Nameplate

Cord

Guide rail

Charge indicator lamp

Ventilation holes

Body

Fig. 4 Fig. 5

12

English

4. AC/DC Adapter

(optional accessories…sold separately)

Plug

Latch

Ventilation holes

Terminals

AC cord

DC cord

Box

Cord armor

Adapter

Error lamp

Power lamp

<ET36A>

Fig. 6

SPECIFICATIONS

1. Cordless Band Saw

Model CB3612DA

Motor DC brushless motor

Band Saw Blade dimensions 44 – 7/8" × 1/2" × 0.020" (1 140 × 12.5 × 0.5 mm)

No-Load Band Saw blade

speed

Standard Mode (1 – 5) 200 – 640 SFPM (60 – 195 m/min)

Auto Mode (A) 395 SFPM (120 m/min)

Max. cutting capacity

Round pipe 4 – 23/32" (120 mm)

Square pipe 5" × 4 – 23/32" (127 mm × 120 mm)

Power supply

Type*

Li-ion battery Model BSL36B18 /

AC/DC adapter Model ET36A (sold separately)

Voltage 36 V

Overall length 20 – 15/32" (520 mm)

Weight 16.5 lbs. (7.5 kg) (BSL36B18 attached)

* Existing batteries (BSL3660/3626/3620, BSL18xx and BSL14xx series, etc.) cannot be used with this tool.

If using the AC/DC adapter, please read and understand its manual before operating the power tool.

2. Battery Charger

Model UC18YSL3

Input power source Single phase: AC 120 V 60 Hz

Charging time

(At a temperature of 68°F (20°C))

BSL36B18 : Approx. 52 min

Charging voltage DC 14.4 – 18 V

Charging current DC 8.0 A

Weight 1.3 lbs. (0.6 kg)

NOTE: The charging time may vary according to temperature and power source voltage.

13

English

NOTE

Due to metabo HPT’s continuing program of research

and development, the speciﬁ cations herein are

subject to change without prior notice.

Electronic control

○

Soft-start

○

Overload protection

This protection feature cuts oﬀ the power to the motor

in the event of overloading of motor or a conspicuous

reduction in rotational speed during operation.

When the overload protection feature has been

activated, the motor may stop.

In this case, release the tool switch and eliminate

causes of overloading.

After that you can use it again.

3. AC/DC Adapter

Model ET36A

Input power source Single phase: AC 120 V 60 Hz

Output voltage 36 V

Operating temperature range 14°F (-10°C) – 104°F (40°C)

Weight

Adapter : 1.8 lbs. (0.8 kg)

Box : 2.6 lbs. (1.2 kg)

○

Overheat protection

This protection feature cuts oﬀ the power to the motor

and stops the power tool in the event of overheating of

motor during operation.

When the overheat protection feature has been

activated, the motor may stop.

In this case, release the tool switch and cool it down in

a few minutes.

After that you can use it again.

ASSEMBLY AND OPERATION

APPLICATIONS

○

Cutting various types of soft steel materials including

conduit pipes, stainless steel pipes, lining steel pipes

and steel rods

○

Cutting nonferrous metal materials including power

and communication cables and aluminum window

frames

○

Cutting plastic (thermoplastic material cannot be cut

as the band saw blade may become wedged in the

material which is prone to melting when heated by

cutting friction

REMOVAL AND INSTRUCTION METHOD

OF BATTERY OR AC/DC ADAPTER

○

How to install the battery or AC/DC adapter.

Align the battery or AC/DC adapter with the groove in

tool housing and slip it into place.

Always insert it all the way until it locks in place with a

little click, If not, it may accidentally fall out of the tool,

causing injury to you or someone around you (Fig. 7).

○

How to remove the battery or AC/DC adapter.

Withdraw battery or AC/DC adapter from the tool

housing while pressing the latch (2 pcs) of the battery

or AC/DC adapter (Fig. 7).

Battery

Pull out

Push

Latch

Insert

Fig. 7

14

English

CHARGING METHOD

NOTE

Before plugging into the receptacle, make sure the

following points.

○

The power source voltage is stated on the

nameplate.

○

The cord is not damaged.

WARNING

Do not charge at voltage higher than indicated

on the nameplate.

If charged at voltage higher than indicated on the

nameplate, the charger will burn up.

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charge

indicator lamp will blink in red. (At 1-second intervals)

WARNING

Do not use the electrical cord

if damaged. Have it repaired

immediately.

2. Insert the battery into the charger.

Firmly insert the battery into the charger as shown in

Fig. 8.

Charge indicator lamp

Guide rail

Battery

Fig. 8

3. Charging

When inserting a battery in the charger, the charge

indicator lamp will blink in blue.

When the battery becomes fully recharged, the

charge indicator lamp will light up in green.(See

Table 2)

(1) Charge indicator lamp indication

The indications of the charge indicator lamp will be

as shown in Table 2, according to the condition of the

battery charger or the battery.

Table 2

Indications of the charge indicator lamp

Charge

indicator

lamp

(RED /

BLUE /

GREEN /

PURPLE)

Before

charging

Blinks

(RED)

Lights for 0.5 seconds. Does not light

for 0.5 seconds. (oﬀ for 0.5 seconds)

Plugged into power source

While

charging

Blinks

(BLUE)

Lights for 0.5 seconds. Does not light

for 1 second. (oﬀ for 1 second)

Battery capacity at less than

50%

Blinks

(BLUE)

Lights for 1 second. Does not light for

0.5 seconds. (oﬀ for 0.5 seconds)

Battery capacity at less than

80%

Lights

(BLUE)

Lights continuously

Battery capacity at more than

80%

Charging

complete

Lights

(GREEN)

Lights continuously

(Continuous buzzer sound: about

6 seconds)

Overheat

standby

Blinks

(RED)

Lights for 0.3 seconds. Does not light

for 0.3 seconds. (oﬀ for 0.3 seconds)

Battery overheated. Unable

to charge. (Charging will

commence when battery cools)

Charging

impossible

Flickers

(PURPLE)

Lights for 0.1 seconds. Does not light

for 0.1 seconds. (oﬀ for 0.1 seconds)

(Intermittent buzzer sound: about

2 seconds)

Malfunction in the battery or the

charger

15

English

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a while.

CAUTION

●

When the battery charger has been continuosly

used, the battery charger will be heated, thus

constituting the cause of the failures. Once the

charging has been completed, give 15 minutes

rest until the next charging.

●

If the battery is charged while it is heated

because it has been left for a long time in a

location subject to direct sunlight or because the

battery has just been used, the charge indicator

lamp of the charger lights for 0.3 seconds, does

not light for 0.3 seconds (oﬀ for 0.3 seconds). In

such a case, ﬁ rst let the battery cool, then start

charging.

●

When the charge indicator lamp ﬂ ickers (at

0.2–second intervals), check for and take out

any foreign objects in the charger’s battery

installation hole. If there are no foreign objects,

it is probable that the battery or charger is

malfunctioning. Take it to your authorized

Service Center.

HOW TO RECHARGE USB DEVICE

When an unexpected problem occurs, the data in a USB

device connected to this product may be corrupted or lost.

Always make sure to back up any data contained in the

USB device prior to use with this product.

Please be aware that our company accepts absolutely no

responsibility for any data stored in a USB device that is

corrupted or lost, nor for any damage that may occur to a

connected device.

WARNING

○

Prior to use, check the connecting USB cable for

any defect or damage.

Using a defective or damaged USB cable can

cause smoke emission or ignition.

○

When the product is not being used, cover the

USB port with the rubber cover.

Buildup of dust etc. in the USB port can cause

smoke emission or ignition.

(2) Regarding the temperature of the rechargeable

battery.

The temperatures for rechargeable batteries are

as shown in the Table 3, and batteries that have

become hot should be cooled for a while before being

recharged.

Table 3

Rechargeable

batteries

Temperatures at which the battery

can be recharged

BSL36B18

32°F – 122°F

(0°C – 50°C)

(3) Regarding recharging time (At 68°F (20°C))

Table 4 Charging time

Charger

Battery

UC18YSL3

BSL36B18 Approx. 52 min.

NOTE

The recharging time may vary according to the

ambient temperature.

4. Disconnect battery charger from the receptacle.

CAUTION

Do not pull the plug out of the receptacle by

pulling on the cord.

Make sure to grasp the plug when removing from

receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the

battery from the battery charger.

NOTE

Be sure to pull out the battery from the battery charger

after use, and then keep it.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the ﬁ rst and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2 – 3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

16

English

NOTE

○

The time required for charging will be longer when

a USB device and battery are being simultaneously

charged.

○

There may be an occasional pause during USB

recharging.

○

When a USB device is not being charged, turn the

USB power switch OFF and remove the USB device

from the charger.

Failure to do so may not only reduce the battery life

of a USB device, but may also result in unexpected

accidents.

(1) Select a charging method

Depending on the charge method selected, either the

battery is inserted into the charger or the power cord

is plugged into an outlet.

○

Charging a USB device by battery (Fig. 9-a)

○

Charging a USB device from a electrical outlet

(Fig. 9-b)

○

Charging a USB device and battery from a

electrical outlet (Fig. 9-c)

abc

Fig. 9

(2) Turn the USB power switch ON (Fig. 10)

When you turn the USB power switch ON, the USB

power indicator lamp will light up.

USB power

switch

USB power

indicator

lamp

Rubber cover

USB port

USB cable

Fig. 10

(3) Connect the USB cable. (Fig. 10)

Pull back the rubber cover and ﬁ rmly plug in a

commercially available USB cable (appropriate to the

device being charged) into the USB port.

○

When the power cord is not plugged into an outlet and

the battery runs out of power, power output will stop

and the USB power indicator lamp will shut oﬀ .

○

When the USB power indicator lamp goes out,

change the battery or plug the power cord into an

electrical outlet.

(4) When charging is completed

○

The USB power indicator lamp will not go out when a

USB device has been completely charged.

To verify charge status, check the USB device.

○

Turn the USB power switch OFF and unplug the

power cord from the electrical outlet. (Fig. 10)

○

Remove the battery from the charger and place the

rubber cover over the USB port.

PRIOR TO OPERATION

1. Preparing and checking the work environment

Make sure that the work site meets all the conditions

laid forth in the precautions.

2. How to use the Hook

The hook can be used to hang up the unit

temporarilyduring operations (Fig. 11).

Hook

Fig. 11

CAUTION

The hook should never be used to hang the

uniton your person.

When using the hook, check to make sure that

the main unit will not slip and fall, or become

unstable by the wind, etc.

Never hang the unit from your belt or trousers as

this could cause accidents.

3. Adjusting the positions of bearing holders (Fig. 12)

WARNING

Securely tighten the M8 bolt.

Insuﬃ cient tightening will not only negatively

aﬀ ect cutting precision, but may also damage

the band saw blade leading to personal injury.

Adjust the spacing between bearing holders

according to the size of the workpiece, and secure

them using M8 bolts.

17

English

M8 bolt

Bearing

holder

Tighten

Loosen

Fig. 12

NOTE

Cutting with excessively large spacing between

bearing holders may shorten the life of the band saw

blade or adversely aﬀ ect cutting precision.

4. Guide plate protrusion adjustment

CAUTION

●

Be sure to switch power OFF and disconnect the

battery from the body when adjusting protrusion

of guide plate.

In the ordinary operation, protrude the guide plate to

the A side fully.

Loosen two M6 ﬂ at-head screws, then slide the guide

plate and secure it by tightening two M6 ﬂ at-head

screws ﬁ rmly.

When the guide plate strikes against the obstacles

like a wall or the like at the ﬁ nishing of a cut, slide it at

the appropriate position. (See Fig. 13)

A

M6 ﬂ at-head

screw

Guide plate

Band saw blade

Hexagonal

bar wrench

(4 mm)

Fig. 13

5. Switch operation (Fig. 14)

Drawing the switch while pressing the switch lock to

either direction indicated by arrow will revolve the band

saw blade while lighting up the LED light.

After the switch is activated and remains drawn, the

band saw blade will continue revolving even if the

Switch Lock is released.

In addition, the LED light will remain lit.

When you release the switch, the revolution of

the band saw blade will stop and the LED light will

automatically be extinguished in approximately 15

seconds.

CAUTION

Do not look directly into the light from the LED

lamp. Continuous and direct exposure to the

light from the LED lamp can injure your eyes.

LED light

Switch lock

OFF

Switch

Fig. 14

NOTE

○

Using a soft cloth, wipe oﬀ any foreign matter that has

adhered to the lens of the LED light, being careful not

to scratch the lens.

Scratches on the LED light may reduce the brightness

of the light.

○

When cleaning the lens of the LED light, do not wipe

with gasoline, paint thinner, etc.

Doing so will damage the lens.

6. Adjusting operating speed (Fig. 15)

CAUTION

Use the band saw blade circumferential speed

setting dial to select the circumferential speed

best suited for the workpiece.

Using a band saw blade circumferential speed

unsuited to cut a workpiece will not only

negatively aﬀ ect cutting precision, but can also

cause damage to the band saw blade.

This unit is equipped with an electronic control circuit

that allows the circumferential speed of the band saw

blade to be freely adjusted.

Prior to operation, use the band saw blade

circumferential speed setting dial to set a mode that

suits the properties, thickness and task conditions of

the workpiece being cut.

18

English

○

In Standard Mode, the circumferential speed or

the band saw blade can be freely set from 1 to 5

on the dial.

On the dial, 1 is the lowest speed and 5 is the

highest speed.

In Standard Mode, the circumferential speed that

is set with the dial is maintained even when the

load changes.

○

In AUTO Mode (“A” on the dial), noise can be

reduced and the duration of operation can be

extended by lowing the circumferential speed

when there is no load.

In AUTO Mode, if a load is applied during operation,

the circumferential speed is automatically

increased. (Equivalent of 5 on the dial)

Additionally, if the load becomes lighter after

cutting is completed, the circumferential speed

is automatically decreased, reducing power

consumption when there is no load.

Dial for setting

band saw blade

circumferential

speed

Fig. 15

Table 5 Operating Speed

Mode Dial

Band saw blade

circumferential speed

(guideline)

Uses

Bi-Metal

Standard

Mode

1 Low Speed 200 SFPM (60 m/min)

Diﬃ cult-to-cut materials such as stainless steel

and alloys

Steel materials

(Thick materials including cylindrical rods,

shaped steel, and steel pipe)

(Thickness of 0.18" (4.6 mm) or more)

Steel materials

(Thin materials including steel pipe)

(Thickness of 0.18" (4.5 mm) or less)

2 305 SFPM (93 m/min)

3 417 SFPM (127 m/min)

4 528 SFPM (161 m/min)

5 High Speed 640 SFPM (195 m/min)

AUTO Mode* A

395 SFPM (120 m/min)

(Idle operation)

Steel materials

(Thin materials including steel pipe)

(Thickness of 0.18" (4.5 mm) or less)

640 SFPM (195 m/min)

(Cutting operation)

* Circumferential speeds may vary from those stated above depending on operating conditions.

7. Replacing the band saw blade

WARNING

●

When replacing the band saw blade, be sure to

switch oﬀ the power and remove the battery from

the cordless tool.

●

Use caution when changing or inspecting the

band saw blade as it may sometimes spring out.

CAUTION

●

Wear gloves when changing the band saw blade.

●

The band saw blade is hot immediately after

operation. Remove it only after it has cooled.

●

Verify that there are no nicks, cracks, or other

abnormalities on the band saw blade before

installing it.

●

Wipe oﬀ any oil or grime adhering to the band

saw blade before installing it on the blade

pulleys.

Additionally, wipe oﬀ any shavings or grime

adhering to the blade pulley rubbers.

If a band saw blade that has oil or grime adhering

to it is installed on the blade pulleys, the band

saw blade may slip or come loose.

●

When installing the band saw blade, do not twist

or bend its joint.

Doing so may damage the band saw blade.

19

English

How to install

(1) Loosen the tension lever in the direction indicated in

the ﬁ gure. (Fig. 16)

Tension lever

Loosen

Fig. 16

(2) Being careful of the direction of revolution and the

facing of the band saw blade (see ﬁ gure), place the

band saw blade in Guide roller, installing the band

saw blade until it comes into contact with the Band

saw blade back ball bearing support.

(3) Holding the band saw blade in place so it doesn’t

come loose, seat the band saw blade in Blade pulley.

(Fig. 17)

Rotation direction

Band saw blade

back holder

Guide rollers

Band saw blade

Fig. 17

(4) Holding the band saw blade in place, turn the Tension

lever in the direction for tightening and secure the

band saw blade. (Fig. 18)

At this point, make sure that the blade of the band saw

blade is not protruding from the edges of Blade pulley.

At this point, rotate Blade pulley (A) in the revolving

direction with your hands and make sure the band saw

blade does not come loose.

Blade pulley (A)

Band saw blade

Blade pulley (B)

Fig. 18

(5) See Steps (3) to (5) of “8. Inspection before operation”

on page 19 when conducting a trial operation.

NOTE

Minimize warm-up cutting with the band saw blade.

Warm-up cutting shortens the lifespan of the band

saw blade.

How to remove (Fig. 19)

(1) Loosen the tension lever in the direction indicated in

the ﬁ gure. (Fig. 16)

(2) Remove the band saw blade ﬁ rst from pulley guard (C)

(

in the ﬁ gure), then from blade pulley (A) and blade

pulley (B), and lastly from the guide rollers section (

in the ﬁ gure) to remove it completely.

Band saw blade

Pulley guard (C)

Blade pulley (A)

Guide rollers

Blade pulley (B)

Fig. 19

CAUTION: on lithium-ion battery

To extend the lifetime, the lithium-ion battery

equips with the protection function to stop the

output. Therefore, if the tool is overloaded, the

motor may stop. However, this is not the trouble

but the result of protection function. In this case,

release the switch of tool and eliminate the

causes of overloading.

8. Inspection before operation

WARNING

Check the following items before you use the

unit. Before taking steps (1) and (2), you must

turn oﬀ the switch and remove the battery from

the main tool unit to perform inspection.

(1) Make sure that the switch is turned oﬀ . (See “5. Switch

operation” on page 17.)

(2) Before use, be sure to conﬁ rm that the band saw

blade is a regular product, and free from any chipping,

cracks, or deformation.

Check that the band saw blade is installed correctly.

(3) Install the battery. (Fig. 7)

(4)

Check the switch lock action. (See “5. Switch operation”

on page 17.)

(5) Run the trial operation.

Ensure surrounding safety before starting operation,

then idle the unit to make sure that no anomalies are

found in unit body vibration and the band saw blade.

(6) Check battery insertion

20

English

CAUTION

●

When switching on the tool, make sure the band

saw blade is not in contact with the workpiece.

Failure to do so may result in injury.

●

For cutting eﬃ ciency, switch the band saw blade

speed according to operating conditions and

workpiece to be cut.

●

Do not apply any unnecessary pressure when

operating the tool. Doing so may damage the

band saw blade.

●

After use, be sure not to place the tool near chips

before it comes to a full stop as the tool may suck

in those particles.

OPERATION

WARNING

●

Be absolutely sure to keep the switch turned oﬀ

and the battery removed to prevent any accident.

●

During operation, do not place your face or

hands near the application tool of the unit.

CAUTION

●

If the band saw blade is locked during cutting,

immediately turn oﬀ the switch and stop

operation.

●

Hold the handle and front handle with both hands

when using the unit.

●

If the unit will not be used over a long period of

time, remove the band saw blade from the unit

body and store it in an appropriate place.

If the band saw blade is left installed in the unit

body for a long period, the lifespan of the band

saw blade will become shorter.

NOTE

○

Select a band saw blade (the band saw blade’s teeth/

inch) and a band saw blade operating speed that is

suitable for properties and thickness of the workpiece

to be cut.

○

When using a new band saw blade, be sure to set

the band saw blade operating speed setting dial to

“1” and perform 1–2 warm-up cuts with a light cutting

load (while pulling slightly upward on the product) on

an object with an outer diameter of 3/4" or less such

as cylindrical rod (carbon steel).

Failure to perform warm-up cuts may result in nicks on

the blade edge and decreased cutting precision.

○

Do not cut thermoplastic material. It can melt from

cutting friction heat which can result in the band saw

blade becoming wedged in the material, causing the

motor to lock up.

○

Do not cut hard materials such as hardened steel.

○

If there is a gap between the guide plate and the

workpiece, the piece may erratically shift position and

cause breakage to the band saw blade.

○

Do not apply excessive loads to the band saw blade.

○

When the workpiece is thin (0.08" thick or less), cut

with the tool slightly raised up.

○

About continuous operation

This tool is equipped with a temperature protection

circuit for safeguarding the motor as well as the

electronic motor drive control components.

If the tool is operated continuously, the temperature

of the unit may rise and activate the temperature

protection circuit, automatically stopping operation. If

this happens, allow the machine to suﬃ ciently cool.

Once the temperature has decreased, the tool is

ready to be used again.

In the event the storage battery is changed during

continuous operation, allow the cordless tool to rest

for about 15 minutes before resuming use.

If operation is resumed soon after the battery is

changed, the temperatures of the motor, switch, etc.

will become high and may result in malfunction or

damage.

○

About holding the unit and applying force

Hold the tool securely with both hands.

When holding the unit, make sure the band saw blade

is perpendicular to the workpiece.

Additionally, there is no need to push the unit with any

excessive force.

Be aware that applying any excessive prying or

pressing force to the tool may result in the unit’s

malfunction or damage.

For stable cut, always keep at least two teeth in the cut.

La page charge ...

Hikoki CB3612DA Manuel utilisateur

Ce manuel convient également à

Hikoki CB3612DA Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents