Motorola Astro APX 3000 Manuel utilisateur

Taper
Manuel utilisateur
English
RF ENERGY EXPOSURE AND PRODUCT SAFETY
GUIDE FOR PORTABLE TWO-WAY RADIOS
APX3000
Before using this radio, read this guide which
contains important operating instructions for
safe usage and RF energy awareness and
control for compliance with applicable standards
and regulations.
ATTENTION!
Motorola Solutions, Inc.
1303 E. Algonquin Rd., Schaumburg,
IL 60196, U.S.A.
*68012007006*
68012007006-AB
*PMLN6300A*
PMLN6300AB
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized
M logo are trademarks or registered trademarks of Motorola
Trademark Holdings, LLC and are used under license. All other
trademarks are the property of their
respective owners.
© 2012 2013 Mo
torola Solutions, Inc.
All rights re
served.
68012007006-A_Covert_SafetyManual.fm Page 1 Thursday, November 22, 2012 11:29 AM
2
English
RF Energy Exposure Awareness and Control Information
and Operational Instructions for Occupational Use
NOTICE: This radio is intended for use in occupational/controlled conditions
where users have full knowledge of their exposure and can
exercise control over their exposure to meet the occupational limits
in FCC and International standards. This radio device is NOT
authorized for general population consumer use.
This two-way radio uses electromagnetic energy in the radio frequency (RF)
spectrum to provide communications between two or more users over a distance.
It uses radio frequency (RF) energy or radio waves to send and receive calls. RF
energy is one form of electromagnetic energy. Other forms include, but are not
limited to, sunlight and x-rays. RF energy, however, should not be confused with
these other forms of electromagnetic energy, which when used improperly, can
cause biological damage. Very high levels of x-rays, for example, can damage
tissues and genetic material.
Experts in science, engineering, medicine, health, and industry work with
organizations to develop standards for safe exposure to RF energy. These
standards provide recommended levels of RF exposure for both workers and the
general public. These recommended RF exposure levels include substantial
margins of protection.
All Motorola two-way radios are designed, manufactured, and tested to ensure
they meet government-established RF exposure levels. In addition, manufacturers
also recommend specific operating instructions to users of two-way radios. These
instructions are important because they inform users about RF energy exposure
and provide simple procedures on how to control it.
68012007006-A_Covert_SafetyManual.fm Page 2 Thursday, November 22, 2012 11:29 AM
3
English
Please refer to the following websites for more information on what RF energy
exposure is and how to control your exposure to assure compliance with
established RF exposure limits:
http://www.fcc.gov/oet/rfsafety/rf-faqs.html
www.who.int/en/
www.motorolasolutions.com/rfhealth
Federal Communication Commission (FCC) Regulations
When two-way radios are used as a consequence of employment, the FCC
requires users to be fully aware of and able to control their exposure to meet
occupational requirements. Exposure awareness can be facilitated by the use of
a product label directing users to specific user awareness information. Your
Motorola two-way radio has a RF Exposure Product Label. Also, your Motorola
user manual, or separate safety booklet includes information and operating
instructions required to control your RF exposure and to satisfy compliance
requirements.
Compliance with RF Exposure Standards
Your Motorola two-way radio is designed and tested to comply with a number of
national and International standards and guidelines (listed below) for human
exposure to radio frequency electromagnetic energy. This radio complies with
the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF
exposure environments at operating duty factors of up to 50% talk-50%
listen and is approved for occupational use only. In terms of measuring RF
energy for compliance with these exposure guidelines, your radio generates
measurable RF energy only while it is transmitting (during talking), not
when it is receiving (listening) or in standby mode.
68012007006-A_Covert_SafetyManual.fm Page 3 Thursday, November 22, 2012 11:29 AM
4
English
NOTE: The approved batteries, supplied with this radio, are rated for a 5-5-90 duty
factor (5% talk-5% listen-90% standby) even though this radio complies
with FCC occupational exposure limits and may operate at duty factors of
up to 50% talk.
Your Motorola two-way radio complies with the following RF energy
exposure standards and guidelines:
United States Federal Communications Commission (FCC), Code of Federal
Regulations;
47 CFR et seq. & FCC, OET Bulletin 65
Institute of Electrical and Electronic Engineers (IEEE) C95.1
International Commission on Non-Ionizing Radiation Protection (ICNIRP)
Ministry of Health (Canada) Safety Code 6 & Industry Canada RSS-102
Australian Communications Authority Radiocommunications Standard et seq.
ANATEL ANNEX to Resolution No. 303 et seq.
RF Exposure Compliance and Control Guidelines and Operating
Instructions for Two-Way Radio Operations
To control your exposure and ensure compliance with the occupational/controlled
environment exposure limits, always adhere to the following procedures.
DO NOT remove the RF Exposure Label from the device.
User awareness instructions should accompany device when transferr
ed to
other user
s.
68012007006-A_Covert_SafetyManual.fm Page 4 Thursday, November 22, 2012 11:29 AM
5
English
Two-Way Radio Operation
Transmit no more than the rated duty factor of 50% of the time. To trans
mit
(talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT
button. The PTT button may reside on the radio itself or may be hosted on
approved wired or wireless (for example, a Bluetooth enabled remote Push-
to-Talkbutton) accessories. Transmitting 50% of the time, or less, is
important because this radio generates measurable RF energy exposure
only when transmitting (in terms of measuring for standards compliance).
NOTE: RF exposures decrease with increasing distance from the antenna.
Body Worn Operation. When worn on the body, always place the radio in a
Motorola-approved clip and carry holster for this product. Using approved
body-worn accessories is important because the use of
non-Motorola-approved accessories may result in exposure level, which
exceed the occupational/controlled environment RF exposure limits.
Use only Motorola-approv
ed supplied or replacement antennas, batteries, and
audio accessories. Use of non-Motorola-approved antennas, batteries, and
accessories may exceed the applicable RF exposure guidelines (iEEE,
ICNIRP or FCC).
For a list of Motorola-approved accessories for your radio model, visit the
following website: http://www.motorolasolutions.com/governmentandenterprise
68012007006-A_Covert_SafetyManual.fm Page 5 Thursday, November 22, 2012 11:29 AM
6
English
Electromagnetic Interference/Compatibility
NOTE: Nearly every electronic device is susceptible to electromagnetic
interference (EMI) if inadequately shielded, designed, or otherwise
configured for electromagnetic compatibility.
Facilities
To avoid electromagnetic interference and/or compatibility conflicts, turn off your
radio in any facility where posted notices instruct you to do so. Hospitals or health
care facilities may be using equipment that is sensitive to external RF energy.
Aircraft
When instructed to do so, turn off your radio when on board an aircraft. Any use of
a radio must be in accordance with applicable regulations per airline crew
instructions.
Medical Devices
Pacemakers
The Advanced Medical Technology Association (AdvaMed) recommends that a
minimum separation of 6 inches (15 centimeters) be maintained between a
handheld wireless radio and a pacemaker. These recommendations are
consistent with those of the U.S. Food and Drug Administration.
Persons with pacemakers should:
ALWAYS keep the radio more than 6 inches (15 centimeters) from their
pacemaker when the radio is turned ON.
Not carry the radio in the breast pocket.
Use the ear opposite the pacemaker to minimize the potential for interference.
Turn the radio OFF immediately if there is any reason to suspect that
interference is taking place.
68012007006-A_Covert_SafetyManual.fm Page 6 Thursday, November 22, 2012 11:29 AM
7
English
Hearing Aids
Some digital wireless radios may interfere with some hearing aids. In the event of
such interference, you may want to consult your hearing aid manufacturer to
discuss alternatives.
Other Medical Devices
If you use any other personal medical device, consult the manufacturer of your
device to determine if it is adequately shielded from RF energy. Your physician
may be able to assist you in obtaining this information.
Use of Communication Devices While Driving
Always check the laws and regulations on the use of radios in the areas where
you drive.
Give full attention to driving and to the road.
Use hands-free operation, if available.
Pull off the road and park before making or answering a call, if driving
conditions or regulations so require.
68012007006-A_Covert_SafetyManual.fm Page 7 Thursday, November 22, 2012 11:29 AM
8
English
Acoustic Safety
Exposure to loud noises from any source for extended periods of time may
temporarily or permanently affect your hearing. The louder the radio's volume, the
less time is required before your hearing could be affected. Hearing damage from
loud noise is sometimes undetectable at first and can have a cumulative effect.
To protect your hearing:
Use the lowest volume necessary to do your job.
Turn up the volume only if you are in noisy surroundings.
Turn down the volume before adding headset or earpiece.
Limit the amount of time you use headsets or earpieces at high volume.
Operational Warnings
For Vehicle With Air Bags:
Refer to vehicle manufacturer's manual prior to installation of
electronic equipment to avoid interference with air bag wiring.
DO NOT place a portable radio in the area over an air bag or in the
air bag deployment area. Air bags inflate with great force. If a
portable radio is placed in the air bag deployment area and the air
bag inflates, the radio may be propelled with great force and
cause serious injury to occupants of the vehicle.
WARNING
68012007006-A_Covert_SafetyManual.fm Page 8 Thursday, November 22, 2012 11:29 AM
9
English
Operational Warnings (Continued)
Potentially Explosive Atmospheres
(Explosive atmospheres refers to hazard classified locations that
may contain hazardous gas, vapors, or dusts.)
Turn off your radio prior to entering any area with a potentially
explosive atmosphere unless it is a portable radio type especially
qualified for use in such areas as Intrinsically Safe (for example,
Factory Mutual, CSA, UL, or CENELEC).
DO NOT remove, install, or charge batteries in such areas. Sparks
in a potentially explosive atmosphere can cause an explosion or
fire resulting in bodily injury or even death.
The areas with potentially explosive atmospheres referred to
above include fueling areas such as below decks on boats, fuel
or chemical transfer or storage facilities, and areas where the air
contains chemicals or particles such as grain, dust or metal
powders. Areas with potentially explosive atmospheres are often,
but not always, posted.
Blasting Caps and Blasting Areas
To avoid possible interference with blasting operations, turn off
your radio when you are near electrical blasting caps, in a
blasting area, or in areas posted: "Turn off two-way radio." Obey
all signs and instructions.
WARNING
68012007006-A_Covert_SafetyManual.fm Page 9 Thursday, November 22, 2012 11:29 AM
10
English
Operational Cautions
Intrinsically Safe Radio Information
The Intrinsically safe approval unit refers to a product that has been approved as
intrinsically safe by an approval agency (for example FM Approvals, CSA, UL, or
Cenelec) and certifies that a particular product meets the Agency's applicable
intrinsic safety standards for specific types of hazardous classified locations. A
portable radio that has been approved for intrinsic safety will have Approval label
attached to the radio to identify the unit as being Approved for specified
hazardous atmospheres. This label specifies the hazardous Class/Division/Group
along with the part number of the battery that must be used. The Intrinsically Safe
Approval Label will be located on the portable radio unit.
Antennas
DO NOT use any portable radio that has a damaged antenna. If a
damaged antenna comes into contact with your skin, a minor burn can
result.
Batteries
All batteries can cause property damage and/or bodily injury, such as
burns, if a conductive material such as jewelry, keys, or beaded chains
touches exposed terminals. The conductive material may complete an
electrical circuit (short circuit) and become quite hot. Exercise care in
handling any charged battery, particularly when placing it inside a
pocket, purse, or other container with metal objects.
Caution
68012007006-A_Covert_SafetyManual.fm Page 10 Thursday, November 22, 2012 11:29 AM
11
English
Operational Cautions for Intrinsic Safe Equipment
Warnings for Radios Approved as Intrinsically Safe
Radios must ship from the Motorola manufacturing facility with the hazardous
atmosphere capability and the intrinsic safety approval labelling (FM, UL, CSA,
CENELEC). Radios will not be upgraded to this capability and labeled once they
have been shipped to the field.
A modification changes the unit’s hardware from its original design configuration.
Modifications can only be made by the original product manufacturer.
DO NOT operate radio communications equipment in a hazar
dous
atmospher
e unless it is a type especially qualified (
for example, FM,
UL, C
SA, or CENELEC approved). An explosion or fire may result.
DO NOT operate a radio unit that has been approved as intr
insically
safe prod
uct in a hazardous atmosphere if it has b
een physically
damaged
(for example, cracked housing). An explosion or fir
e may
res
ult.
DO NOT replace or charge batteries in a hazardous atmosp
here.
Cont
act sparking may occur while installing or removing batteries and
cause an explosion or fire.
Caution
68012007006-A_Covert_SafetyManual.fm Page 11 Thursday, November 22, 2012 11:29 AM
12
English
Repair
DO NOT replace or change accessories in a hazardous atmosphere.
Contact sparking may occur while installing or removing
accessories and cause an explosion or fire.
Turn the radio off before removing or installing a battery or
accessory.
DO NOT disassemble an intrinsically safe product in any way that
exposes the internal circuits of the unit.
Failure to use an intrinsically safe approved battery or Approved
accessories specifically approved for the radio unit may result in
the dangerously unsafe condition of an unapproved radio
combination being used in a hazardous location.
Unauthorized or incorrect modification of the intrinsically safe
approved Product will negate the approval rating of the product.
Incorrect repair or relabeling of any intrinsically safe Agency-
approved radio could adversely affect the Approval rating of the
unit.
Use of a radio that is not intrinsically safe in a hazardous
atmosphere could result in serious injury or death.
REPAIRS FOR MOTOROLA PRODUCTS WITH INTRINSICALLY
SAFE APPROVAL ARE THE RESPONSIBILITY OF THE USER.
Repairs to a Motorola FM approved radio product should only be
done at a location that has been FM audited under the FM 3605
repairs and service standard.
Contact Motorola for assistance regarding repairs and service of
Motorola intrinsically safe equipment.
WARNING
W A R N I N G
68012007006-A_Covert_SafetyManual.fm Page 12 Thursday, November 22, 2012 11:29 AM
13
English
A repair constitutes something done internally to the unit that would bring it back
to its original condition.
Items not considered as repairs are those in which an action is performed on a
unit which does not require the outer casing of the unit to be opened in a manner
that exposes the internal electrical circuits of the unit.
Do Not Substitute Options or Accessories
The Motorola communications equipment certified as intrinsically safe by the
approving agency, (FM, UL, CSA, CENELEC) is tested as a complete system
which consists of the listed agency Approved portable, Approved battery, and
Approved accessories or options, or both. This Approved portable and battery
combination must be strictly observed. There must be no substitution of items,
even if the substitute has been previously Approved with a different Motorola
communications equipment unit. Approved configurations are listed by the
Approving Agency (FM, UL, CSA, CENELEC).
The Intrinsically Safe Approval Label affixed to radio refers to the intrinsically safe
classification of that radio product, and the approved batteries that can be used
with that system.
The manual PN referenced on the Intrinsically Safe Approval Label identifies the
approved Accessories and or options that can be used with that portable radio
unit.
Using a non-Motorola-intrinsically-safe battery and or accessory with the
Motorola approved radio unit will void the intrinsically safe approval of that radio
unit.
68012007006-A_Covert_SafetyManual.fm Page 13 Thursday, November 22, 2012 11:29 AM
14
English
Notes:
68012007006-A_Covert_SafetyManual.fm Page 14 Thursday, November 22, 2012 11:29 AM
Español
Latinoamericano
Folleto de normas de seguridad y exposición a la
energía de RF al usar radios bidireccionales portátiles
ANTES DE UTILIZAR ESTA RADIO, LEA ESTA GUÍA QUE
CONTIENE INSTRUCCIONES DE FUNCIONAMIENTO
IMPORTANTES SOBRE EL USO SEGURO Y CONSCIENTE DE
LA ENERGÍA DE RADIOFRECUENCIA (RF), Y SU CONTROL
PARA CUMPLIR CON LOS ESTÁNDARES Y NORMAS
APLICABLES.
ATENCI
Ó
N
Motorola Solutions, Inc.
1303 E. Algonquin Rd.,
Schaumburg, IL 60196, EE.UU.
MOTOROLA, MOTO, MOTOROLA SOLUTIONS y el logotipo estilizado M son marcas de
fabrica o marcas registradas de Motorola Trademark Holdings, LLC y son usadas bajo
licencia. Todas otras marcas registradas son la propiedad de sus dueños respectivos.
© 2012 Motorola Solutions, Inc.
Todos los derechos están reservados
.
7006_A_SafetyP_LAS.fm Page 1 Thursday, November 22, 2012 11:11 AM
2
Español
Latinoamericano
Información sobre exposición a la energía de RF y su control, e
instrucciones operacionales para uso como herramienta ocupacional
AVISO: Este radio está diseñado para uso en ambientes ocupacionales
controlados donde los usuarios están plenamente conscientes de la
exposición a la energía de radiofrecuencia a la que están sujetos, y
pueden ejercer control sobre dicha exposición para satisfacer los
límites para uso ocupacional establecidos en la normas de la FCC y
demás normas internacionales. Esta unidad de radio NO está
aprobada para la venta al público en general en el mercado de
consumo masivo.
Este radio bidireccional emplea energía electromagnética en el espectro de
radiofrecuencia (RF) para permitir las comunicaciones entre dos o más usuarios
distantes. El mismo emplea la energía de radiofrecuencia u ondas de radio para
enviar y recibir llamadas. La energía de RF es una forma de energía
electromagnética. Este tipo de energía se presenta en otras formas, entre las que
se encuentran la luz solar y los rayos X. La energía de RF, sin embargo, no debe
confundirse con estas otras formas de energía electromagnética que, cuando son
usadas indebidamente, pueden ocasionar daños biológicos. Niveles muy elevados
de rayos X, por ejemplo, pueden producir daños en tejidos y en material genético.
Expertos en las ciencias, la ingeniería, la medicina, la salud y la industria trabajan
conjuntamente con diferentes organizaciones con el fin de desarrollar normas que
definan límites prudentes de exposición a la energía de RF. Estas normas
proporcionan los niveles recomendados de exposición a la RF, tanto para los
trabajadores como para el público en general. Estos niveles recomendados de
exposición a la RF incluyen márgenes de seguridad suficientemente amplios.
Todos los radios bidireccionales Motorola son diseñados, fabricados y probados de
manera que aseguren el cumplimiento de los niveles de exposición a la RF
establecidos por organismos públicos reguladores. Asimismo, los fabricantes
recomiendan a los usuarios de radios bidireccionales seguir instrucciones de
operación específicas. Estas instrucciones son importantes, ya que informan a los
7006_A_SafetyP_LAS.fm Page 2 Thursday, November 22, 2012 11:11 AM
3
Español
Latinoamericano
usuarios acerca de la exposición a la energía de RF y proporcionan
procedimientos sencillos para su control.
Visite los siguientes sitios Web para obtener más información acerca de qué es la
exposición a la energía de RF y cómo controlar la exposición para garantizar la
observancia de los límites de exposición establecidos.
http://www.fcc.gov/oet/rfsafety/rf-faqs.html
http://www.osha.gov/SLTC/radiofrequencyradiation/index.html
Regulaciones de la Comisión Federal de Comunicaciones de
EE.UU. (FCC)
Las normas de la FCC estipulan que los fabricantes de radios portátiles
bidireccionales no podrán comercializar sus productos en los EE.UU., a menos
que los mismos cumplan con los límites de exposición a la energía de RF
establecidos por la FCC. Cuando la naturaleza del trabajo requiere el uso de radios
bidireccionales, la FCC exige que los usuarios estén totalmente conscientes de los
efectos de la exposición, y que sean capaces de controlar el nivel de exposición al
que se someten, a fin de satisfacer los requisitos laborales. La información sobre
exposición puede facilitarse mediante el uso de una etiqueta de producto que
remita a los usuarios a la fuente de información apropiada. Su radio bidireccional
Motorola tiene una etiqueta con información acerca de la exposición a la energía
de RF. Además, en el manual de usuario del producto Motorola, o en un folleto de
seguridad separado, se incluye la información e instrucciones de operación
necesarias para controlar la exposición a la energía de RF y para garantizar el
cumplimiento de las normas.
Conformidad con las normas sobre exposición a la radiofrecuencia
Este radio bidireccional Motorola ha sido diseñado y verificado con el fin de
garantizar su compatibilidad con las siguientes normas y recomendaciones
nacionales e internacionales relacionadas con la exposición de seres humanos a
la energía electromagnética de radiofrecuencia. Este radio cumple con los
límites de exposición establecidos por el IEEE (FCC) y la ICNIRP para
entornos ocupacionales o con control de exposición a la energía de
radiofrecuencia, a niveles de operación de hasta un 50% (50% transmisión/
50% recepción), y está aprobado por la FCC para uso como herramienta
7006_A_SafetyP_LAS.fm Page 3 Thursday, November 22, 2012 11:11 AM
4
Español
Latinoamericano
ocupacional solamente. En lo que respecta a la medición de energía de RF para
la determinación de conformidad con estas pautas de exposición, el radio genera
energía de RF medible sólo cuando está transmitiendo (cuando el usuario está
hablando), no cuando está recibiendo (cuando el usuario está oyendo) ni cuando
está en espera.
NOTA: Las baterías aprobadas que se suministran con este radio soportan un nivel
de operación de 5-5-90 (5% del tiempo transmitiendo, 5% recibiendo y 90%
en espera), aun cuando este radio satisface los límites de exposición
ocupacional de la FCC y puede trabajar a niveles de operación de hasta
50% (50% del tiempo transmitiendo).
Este radio bidireccional Motorola satisface las siguientes normas y
recomendaciones relacionadas con la exposición a la energía de
radiofrecuencia:
Comisión Federal de Comunicaciones de EE.UU. (FCC), Código de Reglamentos
Federales; 47 CFR y siguientes
Comisión Federal de Comunicaciones de EE.UU. (FCC), Boletín OET 65
Instituto de Ingenieros Eléctricos y Electrónicos (IEEE), C95.1
Comisión Internacional para la Protección contra la Radiación No Ionizante
(ICNIRP)
Ministerio de Sanidad (Canadá), Código de seguridad 6
Industria Canadá, RSS-102
Dirección Australiana de Comunicaciones, Normativa de Radiocomunicaciones y
siguientes
ANATEL, Anexo a la Resolución nº 303 y siguientes
Pautas de conformidad y control de la exposición de RF e
instrucciones de operación
Para controlar su exposición y asegurar la conformidad con los límites de
exposición en un entorno ocupacional o controlado, observe siempre los
procedimientos siguientes:
7006_A_SafetyP_LAS.fm Page 4 Thursday, November 22, 2012 11:11 AM
5
Español
Latinoamericano
Pautas:
No retire del dispositivo la etiqueta con información acerca de la exposición a la
energía de RF.
El aparato debe ser acompañado de la información sobre la energía de RF
cuando el mismo sea transferido a otros usuarios.
No use este dispositivo sin antes satisfacer los requisitos operacionales aquí
descritos.
Instrucciones de operación
No transmita más del 50% del tiempo, a fin de no sobrepasar el nivel de
operación máximo especificado del 50%. Para transmitir (hablar) presione el
botón de transmisión (PTT). Para recibir llamadas, suelte el botón PTT. Es
importante no transmitir más del 50% del tiempo, ya que este radio emite
energía de RF medible sólo cuando está transmitiendo (en términos de
conformidad con las normas de medición).
Operación de la unidad ajustada al cuerpo
Cuando use el radio ajustado al cuerpo, colóquelo siempre en un clip,
sujetador para cinturón, estuche o arnés para el cuerpo aprobado por Motorola
para uso con este producto. Es importante emplear accesorios aprobados
para uso con unidades ajustadas al cuerpo, ya que de otra manera el usuario
podría exponerse a niveles de energía de RF superiores a los límites
establecidos por la FCC para entornos ocupacionales o con control de
exposición.
No sujete la antena cuando el radio esté transmitiendo. El sujetar la antena
afecta la calidad de la llamada y podría hacer que el producto de radio funcione
a una potencia mayor que la necesaria.
No toque la superficie metálica de la antena (en posición extendida) cuando el
radio esté transmitiendo. Sentirá una sensación extraña producto de la RF.
Accesorios aprobados
Use únicamente antenas, baterías y accesorios suministrados por Motorola o
reemplazos aprobados por Motorola. Si se emplean antenas, baterías o
accesorios no aprobados por Motorola se podrían exceder los límites de
7006_A_SafetyP_LAS.fm Page 5 Thursday, November 22, 2012 11:11 AM
6
Español
Latinoamericano
exposición a la energía de radiofrecuencia establecidos por la FCC (IEEE) y por
la ICNIRP.
Para consultar la lista de accesorios aprobados por Motorola visite el siguiente
sitio Web donde encontrará una lista de accesorios adecuados para el modelo
del radio en cuestión:
http://www.motorola.com/Business/US-EN/Two-Way+Radios
Información adicional
Para obtener información adicional sobre los requisitos de exposición o sobre
capacitación, visite: http://responsibility.motorolasolutions.com/index.php/
ourapproach/wirelesscommhealth/.
Interferencia y compatibilidad electromagnética
NOTA: Casi todos los dispositivos electrónicos son susceptibles a la interferencia
electromagnética si no cuentan con el debido blindaje, o si no están
diseñados o configurados de manera que sean compatibles con este tipo de
señales electromagnéticas.
Installaciones
Para evitar problemas de interferencia y/o compatibilidad electromagnética, apague
el radio donde haya letreros que así lo establezcan. Por ejemplo, en hospitales e
instalaciones de asistencia médica podrían estar usando aparatos sensibles a la
energía de RF externa.
Aeronaves
Cuando esté a bordo de un avión, apague el radio cuando se le indique. El radio
deberá ser usado de conformidad con las regulaciones de la línea aérea y las
instrucciones de la tripulación.
7006_A_SafetyP_LAS.fm Page 6 Thursday, November 22, 2012 11:11 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58

Motorola Astro APX 3000 Manuel utilisateur

Taper
Manuel utilisateur