Honeywell MN4CFS9 Manuel utilisateur

Portable Air Conditioner

User Manual

Read and save these instructions before use

EN

Climatiseur portatif

Mode d’emploi

Lire ces consignes avant l’utilisation de l’appareil et les conserver

FR

Aire Acondicionado Portátil

Manual del Propietario

Lea y guarde estas instrucciones antes de usar la unidad

ES

Model / Modèle / Modelo:

MN4CFS9/ MN4HFS9/

MN4CFSBB9/ MN4HFSBB9/

MN4CFSWW9/

MN4HFSWW9

Customer Support:

Assistance Au Client:

Servicio de atencion a clientes:

Web: www.HoneywellAirComfort.com

USA: 1-800-474-2147 | [email protected]

CANADA^: [email protected]

^ Canada Customer Support service available for models sold in Canada only.

^ Le Service Client Canadien est disponible uniquement pour les modèles vendus sur le territoire Canadien.

^ Servicio de Atención A Clientes en Canadá disponible solo para modelos vendidos en Canadá.

Check the website for FAQs, usage guides, and more !

Consultez le site Web pour les FAQ, les guides

d'utilisation et plus encore !

Consulte el sitio web para ver las preguntas frecuentes,

las guías de uso y mucho más.

www.HoneywellAirComfort.com

Contact UsProduct Registration

EN

SAFETY

•

DO NOT operate the unit with a damaged plug or loose wall

outlet. If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent, or similarly qualiﬁed persons in

order to avoid a hazard.

DO NOT cover the air intake and exhaust when in use.

DO NOT place objects on or sit on the unit.

Always turn off and unplug the unit when cleaning or servicing.

DO NOT use the appliance if it is damaged.

If service is needed, contact an authorized service agent.

Unplug the unit when stored or not in use.

DO NOT pull or carry the appliance by the power cord.

DO NOT pinch the power cord in the door and DO NOT pull it

along edges or sharp corners.

DO NOT run the power cord under carpeting or rugs.

Use caution to prevent tripping on cord.

DO NOT use the device in the following cases:

- Near a ﬁre source

- In areas where gasoline, paint, or other ﬂammable

goods are stored

- In an area where water is likely to be sprayed or projected.

DO NOT touch the plug or the device with wet hands.

Basic safety precautions should always be followed when using

electrical appliances.

This appliance has been manufactured for use in domestic

environments and should not be used for other purposes.

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS. READ CAREFULLY AND

KEEP FOR FUTURE REFERENCE. IN CASE THERE IS ANY

INCONSISTENCY OR CONFLICT BETWEEN THE ENGLISH

VERSION AND ANY OTHER LANGUAGE VERSION OF THE

CONTENT OF THIS MATERIAL, THE ENGLISH VERSION SHALL

PREVAIL.

WARNING:

EN

SAFETY (CONTINUED)

Only use the installation kit provided to install this unit.

DO NOT attempt to extend the hose or install this unit using

other methods other than those shown in this manual.

Improper installation will void any existing warranties.

DO NOT use an extension cord with this unit.

This appliance can be used by children aged 8 years and

above and persons with reduced physical, sensory, or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance. Cleaning and user

maintenance shall not be made by children without supervision.

Never insert your ﬁngers or rods into the air outlet. Take special

care to warn children of these dangers.

The manufacturer is not liable for injury caused to persons or

property damage due to non-compliance with maintenance

instructions and improper use of the appliance.

The appliance shall be installed in accordance with national

wiring regulations.

The appliance is not to be used by persons (including children)

with reduced physical, sensory, or mental capabilities, or lack

of experience and knowledge, unless they have been given

supervision or instruction.

Children should be supervised to ensure that they do not play

with the appliance.

Electrical equipment and installations regulated by national

legislation must be followed.

The appliance should be transported upright.

DO NOT turn on the appliance for at least one hour before ﬁrst

use.

It is essential that the appliance is connected to an efﬁcient

ground connection checked by a qualiﬁed electrician.

•

EN

SAFETY (CONTINUED)

•

Possible leaks of refrigerant gas in unventilated rooms could

lead to ﬁre or an explosion hazard should the refrigerant come in

contact with electric heaters, stoves, or other sources of ignition.

Use care when storing the appliance to prevent damage that

could cause mechanical faults.

Only persons authorized by an accredited agency certifying their

competence to handle refrigerants in compliance with sector

legislation should work on refrigerant circuits.

DO NOT use means to accelerate the defrosting process or to clean

the unit other than those recommended by the manufacturer.

Flammable substances or pressurized containers (e.g. aerosol

cans) should be kept a minimum of 50cm away from heat or ﬁre.

Use only implements recommended by the manufacturer for

defrosting or cleaning.

DO NOT operate your air conditioner in a wet room such as a

bathroom or laundry room.

The machine works optimally when the humidity is within the

range 3080% RH.

This appliance should be used in a room that allows for good

ventilation between the unit and any walls/furniture or other

objects. The room size should correspond to the room area as

speciﬁed for operation by the manufacturer and the appliance

should be well kept to prevent mechanical damage.

Keep ventilation openings clear of obstructions.

Do not pierce or burn the refrigerants.

Be aware that refrigerants may not contain an odor.

Do not modify this appliance in any way so as to avoid danger.

All working procedures that affect safety shall only be carried out

by competent persons.

EN

R32 SAFETY

SYMBOL NOTE EXPLANATION

WARNING

This symbol shows that this

appliance uses a ﬂammable

refrigerant. If the refrigerant

is leaked and exposed to

an external ignition source,

there is a risk of ﬁre.

CAUTION

This symbol shows that the

operation manual should be

read carefully.

CAUTION

This symbol shows that a

service personnel should be

handling this equipment with

reference to the installation

manual.

CAUTION

This symbol shows that

information is available, such

as the operating manual or

installation manual.

R32

A2L

EN

R32 SAFETY

Read the instructions carefully before using the appliance.

R32 refrigerant gas complies with UL60335240 / UL603351.

This appliance contains a certain number of grams (see

rating label at the back of the unit) of R32 refrigerant gas. The

maximum refrigerant charge amount is not greater than R32

1.84 kg based on UL60335240.

When defrosting or cleaning, do not use any method other than

those recommended by the manufacturer.

Do not place the appliance in a room with continuous sources

of ignition (e.g. open ﬂame, operating gas appliance, or working

electrical heater).

Do not pierce and do not burn.

Do not perforate any part of the refrigerant circuit.

Refrigerant gas may be odorless.

The appliance must be installed, used, and stored in an area that

is greater than R32 gas: 4 m².

Accumulation of possible refrigerant leaks in an unventilated

room could lead to ﬁre or explosion should the refrigerant come in

contact with electric heaters, stoves, or other sources of ignition.

The appliance must be stored in a way to prevent mechanical

damage and in a well-vented area.

Only individuals authorized by an accredited organization

certifying their competence to handle refrigerants in compliance

with industry legislation should work on the refrigerant circuit.

Servicing shall be performed only as recommended by the

manufacturer.

All working procedures that affect safety means shall only be

carried by competent persons.

Additional warnings for appliances with R32 refrigerant gas.

•

EN

R32 SAFETY

Repair must be performed based on the recommendations from the manufacturer.

Maintenance and repair that requires the assistance of other qualiﬁed personnel must be

performed under the supervision of specialists in the use of ﬂammable refrigerants.

CAUTION

Risk of Fire or Explosion due to Flammable Refrigerant Used.

Follow Handling Instructions Carefully in Compliance with National Regulations.

This marking indicates that this product should not be disposed with other household

waste throughout the US. To prevent possible harm to the environment or human

health from uncontrolled waste disposal, recycle it responsibly to promote the

sustainable reuse of material resources. To return your used device, please use return

and collection systems or contact the retailer where the product was purchased. They

can take this product for environmentally safe recycling.

Transport of equipment containing ﬂammable refrigerants must

comply with local transport regulations.

Marketing of equipment using signs must comply with local

regulations.

Disposal of equipment using ﬂammable refrigerants must

comply with national regulations.

The storage of equipment should be in accordance with the

manufacturer’s instructions.

Storage package protection should be constructed such that

mechanical damage to the equipment inside the package will

not cause a leak of the refrigerant charge.

The maximum number of pieces of equipment permitted to be

stored together will be determined by local regulations.

Transportation, marking, and storage for units.

1.

2.

3.

4.

5.

1

THANK YOU

USER TIPS

Congratulations on your purchase of this Honeywell Portable Air Conditioner.

Regarding the information pertaining to the installation, handling, servicing, cleaning, and disposal

of the appliance, please refer to the below section of the manual.

Portable Air Conditioners are ideal for spot cooling. The compressor, condenser, and evaporator are

housed in a compact unit. The air is dehumidiﬁed and cooled while a ﬂexible Exhaust Hose sends

heat outside. The air conditioner includes a window venting kit. No permanent installation is needed.

The unit is easy to move from room to room and offers a truly ﬂexible air conditioning solution.

Auto Evaporation System - The unit automatically evaporates the condensate through the Exhaust

Hose. There is no need to empty the drainage tank except in humid conditions. Read and follow the

instructions carefully.

To ensure optimal efﬁciency of the product, keep doors and windows closed when it is used as an air

conditioner or dehumidiﬁer. If the product is being used with the Fan Function only, an open window

could improve air circulation.

EN

Important:

Before installing the unit, place it UPRIGHT for 1 hour before use to allow the refrigerant to stabilize.

Manually adjust the air vent located at the top of the unit to adjust the direction of air ﬂow.

Follow installation instructions to set up the unit.

Plug the unit into a properly grounded circuit. DO NOT plug into an extension cord.

•

Cooling, Heating* and Dehumidifying

Operation Fan Operation

*Applicable for models with Heating feature only.

2

PARTS DESCRIPTION

EN

1) Air Outlet 7) Power Supply Cord

2) Control Panel

(Incl. Signal Receptor)

8) Upper Grill and Dust Filter

3) Casters 9) Upper Drain Plug

(Dehumidiﬁer Mode)

4) Handle 10) Lower Grill and Dust Filter

5) Air Exhaust Outlet 11) Lower Drain Plug with Plastic Cap

(Air Conditioning Mode)

6) Remote Control

10

9

11

7

8

6

1

4

5

2

3

3EN

INSTALLATION

It is important that the installation instructions below are followed for successful installation of this

Portable Air Conditioner. Please call Customer Support if you have any difﬁculties or queries

regarding these installation procedures.

Installation Kit:

1. Window Bracket Kit (1 Set) 5. Exhaust Hose (1 Piece)

2. Window Bracket Panel Adapter (1 Piece) 6. Insulation Tape (gray,

adhesive)

(1 Piece)

3. Exhaust Hose Connector (1 Piece) 7. Insulation Tape (black,

adhesive)

(1 Piece)

4. Hole Cover (1 Piece) 8. Foam Insulation Pads

(non-adhesive)

(2 Pieces)

1 3

x1 x1x1

2

4

x1

5

x1

6

x1 x1

7 8

x2

4

Installation Steps:

Remove the pre-assembled Exhaust Hose Connector, Exhaust Hose, and Window Bracket Panel

Adapter from the package.

1.

INSTALLATION (CONTINUED)

2. The Window Brackets are approximately 19.7" (50 cm) each, allowing you in install to windows

and balcony doors of different heights or widths.

Adjustable Knobs

EN

19.7" (50 cm)

1 part

19.7" (50 cm) to

38.2" (97 cm)

2 parts

47.2" (1.2 m)

3 parts

Hose:

Length: 12" to 47" (30 cm to 120 cm)

Note: After setting the window bracket to the size of your window, please remove it from the window

and follow the instructions below.

To install the window bracket to the window frame, you need to adjust the height or width of the

window bracket by extending the length according to the height or width of the window. When the

length is set, tighten the Adjustable Knobs (preinstalled on the window bracket) to ensure the window

bracket is secured in the desired position. Use one or all three pieces of window bracket as needed.

5

3. Connect the Exhaust Hose to the rear exhaust outlet on the back of the unit. Slide in the Hose

Connector from up to down. Make sure all sides are secured within the outlet slots.

EN

INSTALLATION (CONTINUED)

4. Connect the window bracket to the window bracket panel adapter by sliding the panel adapter

into the hole of the window bracket, then rotate clockwise until it is locked in place.

6EN

INSTALLATION (CONTINUED)

Measure and cut the Insulation Tape (adhesive) to the full length of your window sash and frame.

Peel off the adhesive backing and slowly attach them to the window sash and frame. The gray

tape should attach to the movable window sash.

5.

Horizontal Sliding Window Vertical Sliding Window

Gray Window Sash

Window Sash

Window Frame Gray

Black Black

6. Connect the window bracket to the window.

7EN

INSTALLATION (CONTINUED)

8. The air conditioner is now ready to use.

7. Position the non-adhesive Foam Insulation Pads on both edges that are not covered by the

adhesive Insulation Tape to seal gaps and prevent air and insects from entering the room.

Horizontal Sliding Window Vertical Sliding Window

Foam

Insulation Tape

(adhesive)

Foam

Insulation Pad

(non-adhesive)

Foam

Insulation Pad

(non-adhesive)

Foam Insulation

Tape (adhesive)

8

INSTALLATION (CONTINUED)

IMPORTANT: Do not change or lengthen the Exhaust Hose as this could cause the unit to

malfunction.

The supplied Exhaust Hose has a diameter of 5.91” (15cm) and can be extended from

12" to 47" (30 cm to 120 cm).

Do not bend (to the extent shown above) the Exhaust Hose. A bent hose will block exhaust air and

cause the unit to malfunction or shut off.

Make sure the back of the unit is at least 31.5" (80 cm) away from the wall and the minimum air

space from top/front/left/right is 20" (50cm). Do not place the unit in front of curtains or drapes

as this could obstruct the airﬂow.

•

WARNING: Any warranties included with this product will be voided if an extra extension hose is

added to the originally provided installation kit or if the installation is performed differently than the

manufacturer's instructions, without proper consultation. Please contact Customer Support for help

with installation procedures if needed.

NOT RECOMMENDED

THE MINIMUM AIR SPACE

RECOMMENDED

31.5" (80 cm)

20" (50 cm)

20"

(50 cm)

20"

(50 cm)

MAX. 14" (36 cm)

EN

MAX. 40" (102 cm)

MIN 35.6 cm

9

USE & OPERATION

EN

CONTROL PANEL

FUNCTION BUTTONS

The Power Control turns the unit on and off. When the unit is plugged in, this button lights up indicating it

is in Standby Mode ready to be switched on anytime.

POWER CONTROL

1) Power Control / Standby Mode 4) Timer/Temperature Set Controls

2) Warning Light (when ﬂashing) 5) Fan Speed Control

3) Mode Control 6) Timer Control

Settings: Air Conditioning, Heating*, Dehumidifying, Fan.

The corresponding indicator light will illuminate to indicate the current mode setting.

MODE CONTROL

Air Conditioning Mode

Adjust fan speed and air temperature to suit your desired comfort level.

Temperature setting range is 16°C - 32°C (61°F - 89°F).

Usage humidity range is 30%80% RH.

•

(6) (5) (4) (4) (3) (1),(2)

Condensation may accumulate in the unit.

If the internal tank becomes full, the Power Control light will ﬂash and the unit will not operate until

the unit has been drained (refer to Water Condensate Drainage).

After switching the air conditioner off, you must wait 3 minutes before switching it back on again.

WARNING LIGHT

*Applicable for models with Heating feature only.

10

USE & OPERATION (CONTINUED)

EN

Heating Mode*

This unit uses HeatPump technology which reverses the air conditioning cooling cycle by

transferring heat from the outside into the room – this is more energy efficient than traditional

electric heaters that generate heat instead of transferring heat into the room. These properties

make this heater ideal for use in autumn or spring when outdoor temperatures are not severely

cold, or as supplemental heating in colder rooms of your home.

•

Fan Mode

For air circulation without air conditioner cooling.

•

Dehumidifying Mode

Air is dehumidiﬁed as it passes through the unit without being in full cooling mode.

If room temperature is higher than 25°C (77°F), fan speed can be adjusted. Otherwise, fan speed

is preset to LOW.

Note: If the unit will be used mainly as a dehumidifier, do not connect the Exhaust Hoses.

Continuous drainage is then necessary (refer to Continuous Draining for Dehumidiﬁer Mode).

•

When heating mode is selected, the indicator light will shine. Heating is activated only when

the ambient temperature is below 25°C (77°F). In this mode, the desired temperature can be

set between 16°C 25°C (61°F - 77°F).

Note: The Exhaust Hoses must vent outside the room when using heating mode.

IMPORTANT: The Heat pump draws moisture from the air which then condenses into the

internal water tank. The unit will pause operation when the tank is full and will restart when

the tank has been emptied. It is recommended to use the heating mode in a room with 50%

humidity or lower. Avoid operating moisture-producing products or appliances such as a

humidifier or a kettle when using the unit in heating mode.

See the "Draining Water Condensate in Heat Mode" section for more information on draining

the water tank.

FUNCTION BUTTONS (CONTINUED)

IMPORTANT: The Dehumidiﬁer mode is used to support moisture reduction but should not be

expected to dehumidify to the same degree as a standard dehumidiﬁer-only appliance. The

built-in dehumidiﬁer automatically adjusts dehumidiﬁcation based on ambient room temperatures.

It is not possible to adjust to a desired humidity percentage. The front display only shows the

current AND desired temperatures. It does not show humidity levels.

*Applicable for models with Heating feature only.

11

EN

FUNCTION BUTTONS (CONTINUED)

While the unit is turned on, press the timer button, then press the ▼ or ▲ to select the number of

hours you would like the unit to continue to run. The unit will turn off automatically.

AUTO TURN OFF:

While unit is running, press the ▼ or ▲ button to select the number of hours you want the unit to run

in air conditioning mode.

AUTO TURN ON:

When unit is in standby mode (plugged in with power light on), press the ▼ or ▲ button to select the

number of hours until you want the unit to automatically start running.

TIMER CONTROL

TEMPERATURE / TIMER SET CONTROLS

Used for adjusting the timer and thermostat.

The default display is the set temperature.

In cooling mode, when ▼ or ▲ button is pressed, the set temperature is displayed and may be

adjusted. After 10 seconds, the display will revert back to room temperature. Temperature is only

adjustable in cooling mode. The time is adjustable between 1 - 24 hours.

Note: By pressing both ▼ or ▲ buttons at the same time, the display will toggle between

Celsius(°C) and Fahrenheit(°F).

•

3 settings: High, Medium, and Low.

FAN SPEED CONTROL

USE AND OPERATION (CONTINUED)

12EN

USE & OPERATION (CONTINUED)

REMOTE CONTROL

The functions work the same as the Portable Air Conditioner's Control Panel.

All key functions can be accessed from the remote control.

Note:

Battery Installation: Remove the cover on the back of the remote control and insert two AAA

batteries with + and - pointing in the proper direction according to the polarity markings.

•

Use only two AAA or IEC R03 1.5V batteries.

Remove the batteries if the remote control is not in use for a month or longer.

All batteries should be replaced at the same time. Do not mix with old batteries.

Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.

Properly dispose of used batteries.

•

Caution:

Power Control

ON/OFF

Temperature/Timer Set

Used for adjusting the timer and

temperature.

When the ▼ or ▲ key is pressed, the

set temperature is displayed and

may be adjusted

Timer setting is available from 1 - 24 hours

by pressing the key ▼ or ▲.

•

Fan Speed Control

Timer Control

In running mode: Auto switch off

In standby mode: Auto switch on

Press ▼ or ▲ button to adjust the

time setting by 1 hour intervals.

HIGH/MID/ LOW

Mode Control

Air Conditioning Dehumidifying

Heating* Fan

Press this button to change the operation

mode in the order of:

*Applicable for models with Heating feature only.

This device complies with part 15 of the FCC Rules. Operation is subject to following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment dose cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

Caution: Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority

to operate the equipment.

13

CLEANING & MAINTENANCE

EN

Appliance Maintenance:

Turn off the appliance before disconnecting the power supply.

Only clean the appliance with a soft, dry cloth.

1.

2.

WARNING: DO NOT power or operate the Air Conditioner when cleaning or when any or both of the

Rear Grills are removed from the unit, or if there is a loose-ﬁtting Rear Grill(s). DO NOT attempt to

handle or touch any of the parts or wiring inside the air conditioner after the Rear Grill(s) are removed

from the unit. Doing so can cause serious injury or electrical shock.

Switch off and unplug the air conditioner from

the electrical outlet.

Remove the Upper Dust Filter and the Lower Dust Filter.

Gently wash using water and/or diluted liquid dishwashing

detergent.

Rinse thoroughly and gently shake excess water from

the ﬁlters. Make sure the ﬁlters are dry before reinstalling.

Note: You may use a vacuum cleaner to remove dust.

Replace the Upper Dust Filter and the Lower Dust Filter

onto the unit.

1.

2.

3.

4.

Dust Filter Maintenance:

The dust ﬁlter is to be cleaned every two weeks to maintain

air cooling efﬁciency. Please follow the below instructions to

clean the dust ﬁlter:

Rear Grill

Lower

Dust Filter

Upper

Dust Filter

La page charge ...

Honeywell MN4CFS9 Manuel utilisateur

Honeywell MN4CFS9 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents