DeWalt DXAELJ16 Le manuel du propriétaire

Marque: DeWalt

Modèle: DXAELJ16

Taper: Le manuel du propriétaire

DXAELJ16CA

LITHIUM AUTOMOTIVE JUMP STARTER WITH USB POWER BANK

BLOC D’ALIMENTATION POUR DÉMARRAGE DE SECOURS

AUTOMOBILE AU LITHIUM AVEC CHARGEUR PORTATIF USB

INSTRUCTION MANUAL

MODE D’EMPLOI MANUAL DE

INSTRUCCIONES

If you have questions or comments, contact us.

Si vous avez des questions ou des commentaires, contactez-nous.

1-888-394-3392

RD080122

English

 ADVERTENCIA: Lea todas las instrucciones antes de utilizar

el producto. No seguir todas las instrucciones que aparecen a

continuación pueden provocar descargas eléctricas, incendios

y/o lesiones graves.

ADVERTENCIA: Este producto o su cable de alimentación contiene

plomo, una sustancia química reconocida por el Estado de California

como causante de cáncer, defectos de nacimiento u otros problemas

reproductivos. Lávese las manos después de utilizarlo. Para más

información, visite www.P65Warnings.ca.gov

 WARNING: Read all instructions before operating product.

Failure to follow all instructions listed below may result in electric

shock, fire and/or serious injury.

WARNING: This product or its power cord contains lead, a chemical

known to the State of California to cause cancer and birth defect or

other reproductive harm. Wash hands after handling. For more

information go to www.P65Warnings.ca.gov

English

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity for each signal

word. Please read the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which,

if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS

DEWALT TOOL, CALL US TOLL FREE AT: 1-888-394-3392.

Lithium Automotive Jump Starter with

USB Power Bank

The DXAELJ16 1600A Jump Starter and 3.1A USB Ports is a DeWALT

jump starter that features a USB-A & USB-C charging ports.

Important Safety

Instructions

1. Keep these instructions.

2. Heed all warnings.

3. Follow all instructions.

4. Avoid dangerous environments. Don’t use this unit in damp or wet

locations; or in the rain or snow.

5. Clean only with a dry cloth.

6. Keep children away from the work area. Keep this unit away from

children. This is not a toy!

7. Store indoors. When not in use, this unit should be stored indoors

in a dry and high or locked-up place – out of the reach of children.

8. Stay alert. Use common sense. Do not operate this equipment

when you are tired or impaired.

9. Only use attachments/accessories specified by the manufacturer.

The use of any accessory or attachment not recommended for

use with this appliance could be hazardous.

10. Use only on a flat, level surface. If a cart is used,

use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

11. To reduce risk of electric shock, disconnect the

unit from any power source before attempting

maintenance or cleaning. Turning off controls

without disconnecting will not reduce this risk.

12. Check for damaged parts. Any part that is damaged should be

properly repaired or replaced by manufacturer unless otherwise

indicated elsewhere in this instruction manual before further

use. Servicing is required when the unit has been damaged in

any way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the unit, the unit has

been exposed to rain or moisture, does not operate normally, or

has been dropped. Do not disassemble the unit; return it to the

manufacturer when service or repair is required.

Opening the unit may result in a risk of electric shock or fire, and

will void warranty. Contact the manufacturer at 1-888-394-3392

for more information.

13. Unit shall not be exposed to dripping or splashing and no objects

filled with liquids, shall be placed on the unit.

14. Do not operate this unit near flammable liquids or in gaseous or

explosive atmospheres.

English

15. This unit employs parts (switches, relays, etc.) that produce arcs

or sparks. Therefore, if used in a garage or enclosed area, the

unit MUST be placed not less than 18 inches above the floor.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

NOTICE: Per FCC Part 15, changes or modifications to this equipment

not expressly approved by DEWALT could void your authority to operate

this equipment.

READ ALL INSTRUCTIONS

GENERAL SAFETY WARNINGS AND INSTRUCTIONS

WARNING – To reduce the risk of fire, electric shock:

• The Smart Cables Controller and Smart Cables Port are

always “live”! NEVER insert fingers into the sockets or attempt

to disassemble the unit.

• Do not put the unit in water or other liquid. Do not place or

store this unit where it can fall or be pulled into water. Do not

expose it to rain, snow or use when wet.

• Charge indoors only.

• Use only the USB charging cable supplied by the manufacturer

to recharge.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM BATTERIES

WARNING – To reduce the risk of fire, electric shock,

burst hazard, or injury to persons or property: Lithium batteries

are small, compact and ideal for providing long-lasting power to this

unit. However, they must be used and charged properly. Improper

use can result in serious injury, fire, or death.

• Lithium batteries can explode in the presence of a source of

ignition. Do not use the product in the presence of an

open flame.

• Do not place this lithium battery powered unit in fire or apply

heat to it.

• Do not subject this lithium battery powered unit to strong

impacts or shocks. The battery in this unit contains safety and

protection devices which, if damaged, may cause the battery to

generate heat, rupture or ignite.

• Do not expose this lithium battery powered unit to water or salt

water, or allow the battery to get wet.

English

• Avoid storing this lithium battery powered unit in the basement,

bathroom or other areas of the house that are or may become

wet or humid or where moisture may concentrate.

• Do not leave this lithium battery powered unit in direct sunlight,

or use or store the unit inside cars in hot weather. Doing so

may cause the battery to generate heat, rupture, or ignite.

Using the battery in this manner may also result in a loss of

performance and a shortened life expectancy.

• Never charge this unit near heat or flammable objects.

• NEVER THROW WATER ON A BURNING LITHIUM

BATTERY! If a lithium battery does catch on fire, it will burn

even more violently if it comes in contact with water or even

moisture in the air. A fire extinguisher must be used.

Battery Charging and Capacity

This unit is delivered in a partially charged state – you must fully

charge it before using it for the first time.

When stored at room temperature with a full charge, lithium

batteries will begin to discharge from the time they are

manufactured, even when unused. Deep discharges also decrease

their capacity. Battery life can be extended by the following:

• Charge battery to full capacity before storage.

• Store this unit at temperatures between 5°C and 20°C (41°F

and 68°F).

• Never discharge the battery fully.

• Charge after each use.

• Always charge at least once every 3-6 months if not in frequent

use to prevent overdischarge.

Transportation of Lithium Batteries

• Always check all applicable local, national, and international

regulations before transporting a unit containing a lithium battery.

• Transporting an end-of-life, damaged, or recalled battery may, in

certain cases, be specifically limited or prohibited.

INSTRUCTIONS PERTAINING TO THE

12V DC/USB CHARGING ADAPTER

CAUTION – To avoid the risk of property damage:

• The 12 Volt DC charging adapter must only be connected to

batteries with a nominal output voltage of 12 volts. The unit will

not operate from a 6 volt battery and will sustain permanent

damage if connected to a 24 volt battery.

• Always connect the 12 volt DC/USB charging adapter to the 12

volt DC power source before plugging any devices into it.

• NEVER connect the 12V DC/USB charging adapter to a

positive grounded vehicle.

Speciﬁc Safety Instructions for

Jump Starters

WARNING – Burst hazard: Do not use the unit for charging dry-cell

batteries that are commonly used with home appliances. These

batteries may burst and cause injury to persons and damage property.

Use the unit for boosting a lead-acid battery only. It is not intended to

supply power to a low-voltage electrical system other than in a starter-

motor application.

WARNING: To reduce the risk of electric shock, never immerse this

unit in water or any other liquid, or use when wet.

WARNING – Risk of explosive gases:

• Working in the vicinity of a lead acid battery is dangerous. Batteries

generate explosive gases during normal battery operation. For this

reason, it is of the utmost importance that each time before using

the jump-starter you read this manual and follow instructions exactly.

• To reduce the risk of battery explosion, follow these instructions and

those published by the battery manufacturer and manufacturer of

English

any equipment you intend to use in the vicinity of the battery. Review

cautionary markings on these products and on the engine.

WARNING – To reduce the risk of fire:

• Do not operate near flammable materials, dust, fumes or gases.

• Do not expose to extreme heat or flames.

CAUTION – To reduce the risk of injury or property damage:

• NEVER ATTEMPT TO JUMP-START OR CHARGE A FROZEN

BATTERY.

• Make sure the cord is located so that it will not be stepped on, tripped

over or otherwise subjected to damage or stress.

• Do not leave the unit unattended while in use.

• Pull by the plug rather than the cord when disconnecting the USB

Charging Cable.

• Vehicles that have on-board computerized systems may be damaged

if vehicle battery is jump-started. Before jump-starting, read the

vehicle’s owner’s manual to confirm that external-starting assistance

is suitable.

• When working with lead acid batteries, always make sure immediate

assistance is available in case of accident or emergency.

• Always have protective eyewear when using this product: contact with

battery acid may cause blindness and/or severe burns. Be aware of

first aid procedures in case of accidental contact with battery acid.

• Have plenty of fresh water and soap nearby in case battery acid

contacts skin.

• Never smoke or allow a spark or flame in vicinity of vehicle battery,

engine or power station.

• Stay clear of fan blades, belts, pulleys, and other parts that can

cause injury to persons.

• Remove personal metal items such as rings, bracelets,

necklaces and watches when working with a lead acid battery. A

lead acid battery can produce a short circuit current high enough to

weld a ring, or similar metal object, to skin, causing a severe burn.

• Do not wear vinyl clothing when jump-starting a vehicle. Friction can

cause dangerous static-electrical sparks.

• Do not wear loose clothing or jewelry. They can be caught in

moving parts. Rubber gloves and substantial, non-skid footwear are

recommended when working outdoors. Wear protective hair covering

to contain long hair.

• Be extra careful to avoid dropping a metal tool onto the battery. It

might spark or short-circuit the battery or another electrical part and

could cause an explosion.

• Jump-start procedures should only be performed in a safe, dry,

well-ventilated area.

• Always store battery clamps when not in use. Never touch battery

clamps together.

• Make sure to connect the clamps with correct polarity.

• Do not expose battery to fire or intense heat since it may explode.

Before disposing of the battery, protect exposed terminals with

heavy-duty electrical tape to prevent shorting (shorting can result

in injury or fire).

• Place this unit as far away from the battery as cables permit.

• Never allow battery acid to come in contact with this unit.

• Do not operate this unit in a closed area or restrict ventilation in any

way.

• This system is designed to be used only on vehicles with a 12 volt DC

battery system. Do not connect to a 6 volt or 24 volt battery system.

• Excessive engine cranking can damage a vehicle’s starter motor. If

the engine fails to start after the recommended number of attempts,

discontinue jump-start procedures and look for other problems that

may need to be corrected.

• Do not use this jump starter on a watercraft. It is not qualified for

marine applications.

English

INSTRUCTIONS PERTAINING TO THE

USB PORTS

IMPORTANT:

Some household USB-powered electronics will

not operate with the USB ports provided with this unit and

its charging adapters.

Check the manual of the corresponding electronic devices

(including phones, tablets, etc.) to confirm that they can be used with one of these USB ports and

which USB port to use (Type A or Type C).

The USB ports do not support data communication. They only

provide power to an external USB powered device, as follows:

– 5V DC/3.1A maximum using the Type A and Type C USB ports on the unit;

– 5V DC/2A using the USB ports on the AC/USB or DC/USB Charging Adapters).

Make sure the rating of equipment plugged into the USB port does not exceed the amperage

stated.

• Always connect the appropriate charging adapter to either the

120V AC or 12V DC power source before plugging any devices

into it.

• Do not attach USB hubs allowing connection of multiple

personal electronic devices to any of the USB ports on the

charging adapters.

• Do not insert foreign objects into any of the USB Ports.

FIRST AID

When working with lead acid batteries, always make sure immediate assistance is available in

case of accident or emergency.

Always have protective eyewear when using this product: contact with battery acid may cause

blindness and/or severe burns. Be aware of first aid procedures in case of accidental contact

with battery acid.

• Have plenty of fresh water and soap nearby in case battery acid

contacts skin.

• Remove personal metal items such as rings, bracelets, necklaces

and watches when working with a lead acid battery. A lead acid

battery can produce a short circuit current high enough to weld

a ring, or similar metal object, to skin causing a severe burn.

• Stay clear of fan blades, belts, pulleys, and other parts that can

cause injury to persons.

• Be extra cautious to avoid dropping a metal tool onto the

battery. It might spark or short-circuit the battery or another

electrical part, and that may cause an explosion.

• Never smoke or allow a spark or flame in vicinity of vehicle

battery, engine or battery charger.

• SKIN: If battery acid contacts skin or clothing, wash

immediately with soap and water for at least 10 minutes. If

redness, pain, or irritation occurs, seek immediate medical

attention.

• EYES: If battery acid comes in contact with eyes, flush eyes

immediately, for a minimum of 15 minutes and seek immediate

medical attention.

SAVE THESE

INSTRUCTIONS

FOR FUTURE USE

English

WARNING – To reduce the risk of injury:

Follow these instructions and

those published by the battery manufacturer and manufacturer of any equipment you intend to use with

this unit. Review cautionary markings on these products and on engine.

INTRODUCTION

Congratulations on purchasing your new Lithium Jump-Starter / Power Bank. Read this

Instruction Manual and follow the instructions carefully before using this unit.

IMPORTANT NOTES:

• Several factors can affect a jump-starter’s ability to boost a

vehicle’s battery, including, but not limited to the size of the

battery, the temperature (hot or cold), whether the battery is

damaged or defective, and whether the jump-starter itself is fully

charged.

• The jump-starter requires a minimum voltage to detect the

correct connection before it will begin to boost. If the vehicle

battery voltage is below approximately 2 volts, it may not be able

to detect connection and may not be able to start the vehicle.

While this low battery voltage is rare it may occur under extreme

conditions.

English

1. USB-A and USB-C Power

Ports

2. 200 Lumen LED Light

3. Power Button

4. LED Status Indicators

5. Smart Cables Controller

6. Metal Battery Clamps

7. DC Charger

8. AC Charger

9. USB Charging Cable

FEATURES

English

Viewing Battery Status

The Battery Status LED Indicators indicate the battery charge level

as follows:

• If the battery charge level is at full capacity, all three Battery

Status LED Indicators light.

• If the battery is at partial charged, two Battery Status LED

Indicators light.

• If the battery is nearly empty, only one Battery Status LED

Indicator lights. The unit should be charged at this time.

• If the battery is completely empty, only one Battery Status LED

Indicator flashes. The unit MUST be charged at this time or the

unit’s built-in low voltage protection will activate and the unit

will automatically shut down.

CHARGING / RECHARGING

This unit is shipped in a partially charged state. Charge the unit after purchase, before first use, and

after each subseuent use until all three blue Battery Status LED Indicators light when the Power

Button is pressed (with the adapter unplugged from the unit).

IMPORTANT:

When the unit is not in use, we recommend that the battery is charged at

least every 3 to 6 months. Failure to keep the battery charged will cause permanent damage and

result in poor performance.

NOTES:

• When the Type A USB port is in use in the charging process,

the Type C port will have no output. Pressing the Power

Button during the charging process will only control the LED

Light.

• When the unit battery is fully charged, the charging process will

terminate and the unit will automatically shut down.

• A 2A USB is required in order to recharge the unit (2A AC and

DC charging adapters included).

• During the charging process, the unit will stop charging if

the battery of the unit is overheated due to extensive use or

recharging. The charging process will automatically resume

after a cool down period.

CHARGING/RECHARGING USING THE 120 VOLT AC/USB

CHARGING ADAPTER

IMPORTANT: Always connect the 120V AC/USB Charging Adapter

to the 120 Volt AC power source (using the USB Charging Cable)

BEFORE connecting it to the unit.

1. Make sure the Power Button is turned off (the Battery Status

LED Indicators are not lit).

2. Insert one end of the USB Charging Cable into the 120V AC/

USB Charging Adapter.

3. Insert the 120V AC/USB Charging Adapter into a standard 120

volt AC wall outlet or a functioning 120 volt AC power source.

4. Lift up the protective cover of the USB ports. Insert the other

end of the USB Charging Cable into the unit’s Type A USB

port.

5. The blue Battery Status LED Indicators will gradually light up (left

to right) to indicate the unit is charging.

6. Charge for approximately 6 hours or until the unit automatically

shuts down.

7. Unplug the 120V AC/USB Charging Adapter from the 120 volt

AC power source, then disconnect the USB Charging Cable

from the 120V AC/USB Charging Adapter, and then from the

unit’s Type A USB port.

8. Press the Power Button to turn the unit on. When all three

blue Battery Status LED Indicators light, the unit battery is fully

charged.

9. Store the 120V AC/USB Charging Adapter and USB Charging

Cable in a safe place.

English

CHARGING/RECHARGING USING THE 12V DC/USB

CHARGING ADAPTER

IMPORTANT: Always connect the 12V DC/USB Charging Adapter

to the 12 volt DC power source (using the USB Charging Cable)

BEFORE connecting it to the unit.

1. Make sure the Power Button is turned off (the Battery Status

LED Indicators are not lit).

2. Insert one end of the USB Charging Cable into the 12V DC/

USB Charging Adapter.

3. Insert the 12V DC/USB Charging Adapter into a vehicle’s 12

volt DC accessory outlet or other functioning 12V DC power

source. The LED indicator on the 12V DC/USB Charging

Adapter will light green when it is properly plugged into the 12

volt DC power source.

Note: Some vehicles require that the ignition be switched to

the accessory outlet position in order to power the accessory

outlet.

4. Lift up the protective cover of the USB ports. Insert the other

end of the USB Charging Cable into the unit’s Type A USB

port.

5. The blue Battery Status LED Indicators will gradually light up

(left to right) to indicate the unit is charging.

6. Charge until the unit automatically shuts down. Unplug the 12V

DC/USB Charging Adapter from the 12 volt DC power source,

then disconnect the USB Charging Cable from the 12V DC/

USB Charging Adapter, and then from the unit’s Type A USB

port.

7. Press the Power Button to turn the unit on. When all three

blue Battery Status LED Indicators light, the unit battery is fully

charged.

8. Store the 12V DC/USB Charging Adapter and USB Charging

Cable in a safe place.

CHARGING/RECHARGING USING THE USB CHARGING

CABLE AND A DEVICE WITH A USB POWER PORT (NOT

SUPPLIED)

IMPORTANT: Always connect the USB Charging Cable to the

external device’s USB power port BEFORE connecting it to the unit.

A 2A USB power source is required in order to recharge the unit.

1. Make sure the Power Button is turned off (the Battery Status

LED Indicators are not lit).

2. Insert one end of the USB Charging Cable into an external

device’s functional USB power port.

3. Lift up the protective cover of the USB ports. Insert the other

end of the USB Charging Cable into the unit’s Type A USB

port.

4. When the unit is properly connected, the blue Battery Status

LED Indicators will gradually light up (left to right) to indicate

the unit is charging.

5. Charge until the unit automatically shuts down.

6. Disconnect the USB charging cable from the device’s USB

power port and the unit.

7. Press the Power Button to turn the unit on. When all three

blue Battery Status LED Indicators light, the unit battery is fully

charged.

8. When charging is complete, store the USB Charging Cable in

safe place.

English

OPERATING INSTRUCTIONS

JUMP-STARTING USING THE SMART CABLES

Battery Clamp Connection Precautions

• Connect and disconnect the battery clamps only after unplugging

the power source.

• Make sure the engine is not running when connecting or

disconnecting the battery clamps.

• Never allow clamps to touch each other.

• Attach clamps to battery and chassis as indicated in the section

“Connecting the Jump-Starter Using the Included Battery

Clamps”.

CONNECTING THE JUMP-STARTER USING THE INCLUDED

BATTERY CLAMPS

1. Position the Smart Cables Controller to reduce risk of damage

by the car hood, doors, or moving engine parts.

2. Stay clear of fan blades, belts, pulleys, and other parts that

can cause injury to persons.

3. Check polarity of battery posts. The positive (POS, P, +) battery

post usually has larger diameter than the negative (NEG, N, –)

post.

4. Connect the Smart Cables Connector to the Smart Cables

Port. Be especially careful, since both the Connector and

Controller are “live.”

5. Connect the positive (RED) clamp from the jump-starter to the

positive (POS, P, +) ungrounded battery post. Connect the

negative (BLACK) clamp to the negative (NEG, N, –) battery

post, the vehicle chassis or engine block away from the

battery. Do not connect the clamp to the carburetor, fuel lines

or sheet-metal body parts. Connect to a heavy gauge metal

part of the frame or engine block.

Note: If the battery clamps are incorrectly connected with

regard to polarity, the Bi-Color Jump-Starter Status Indicator

on the Smart Cables Controller will light red until the clamps

are disconnected. Remove the clamps and then reconnect

them with the correct polarity.

6. When disconnecting the jump-starter, first remove the negative

BLACK (–) clamp from the negative battery post or the vehicle

chassis, and then remove the positive RED (+) clamp from the

positive battery post. Disconnect the double barrel connector

of the Smart Cables Controller from the Smart Cables Port of

unit. Store the Smart Cables Controller in a safe place.

Procedure

Take the following steps, observing all cautions and warnings in the

“Important Safety Instructions” section at the front of this manual.

1. Turn off vehicle ignition and all accessories (radio, A/C, lights,

connected cell phone chargers, etc.). Place vehicle in “park”

and set the emergency brake.

2. Make sure all the unit functions are turned off (the Battery

Status LED Indicators are not lit) and the USB Charging Cable

is NOT connected.

3. Lift up the protective cover of the unit’s Smart Cables Port.

Insert the double-barrel Smart Cables Connector into the

Smart Cables Port on the unit.

4. Set up the unit as described in the “Connecting the Jump-

starter Using Included Battery Clamps” section, observing all

warnings and cautions in the “Important Safety Instructions”

section.

5. When the unit is properly connected, the Bi-Color Status

Indicator on the Smart Cables Controller will light green.

6. Turn on the ignition and crank the engine in 5-6 second bursts

until the engine starts.

English

7. When the process is completed, disconnect the jump-starter.

First remove the negative BLACK (–) clamp from vehicle

chassis, and then remove the positive RED (+) clamp from

the positive battery post. Disconnect the double barrel Smart

Cables Connector from the Smart Cables Port.

8. Store the Smart Cables Controller in a safe place.

9. Recharge the unit fully.

IMPORTANT NOTES:

If the battery clamps are incorrectly connected with regard to polarity,

the Bi-Color LED Status Indictor will light red until the clamps are

disconnected. Remove the clamps and then reconnect them with

correct polarity.

If the voltage of the unit’s internal lithium battery is low and has

insufficient output power, the Bi-Color LED Status Indictor will light

red. Disconnect the unit and fully charge following the directions in

the “Charging / Recharging” section.

If the Smart Cables Controller is overheated, the Bi-Color LED

Status Indictor will light red. Disconnect the Battery Clamps and

allow the unit to cool down for a period before resuming any

operation.

If the cranking current and/or time period exceeds the unit’s

parameters, the Bi-Color LED Status Indictor will flash red for

50 seconds (a cooling down period) before lighting green again

(resuming normal operation).

CAUTION – To avoid the risk of property damage:

• If the vehicle doesn’t start after the first attempt, allow a resting/

cooling period of 4 to 5 minutes before making asecond attempt.

If a second attempt doesn’t start the vehicle, discontinue use

and look for other problems that need to be corrected. The

battery may be damaged.

• NEVER attempt to use the unit to start a vehicle while it is in

charging mode.

• Using the jump-starter without a car battery installed in the

vehicle will damage the vehicle’s electrical system.

IMPORTANT: Always turn the unit off when not in use. Recharge this

unit fully after each use.

CAUTION – TO REDUCE THE RISK OF PROPERTY DAMAGE:

• Vehicles that have on-board computerized systems may be damaged

if vehicle battery is jump-started. Before jump-starting this type of

vehicle, read the vehicle manual to confirm that external-starting

assistance is advised.

• Excessive engine cranking can damage the vehicle‘s starter motor. If

the engine fails to start after the recommended number of attempts,

discontinue jump-start procedure and look for other problems that

need to be corrected.

• If vehicle fails to start, turn off the ignition, disconnect the jump-start

system’s leads and contact a qualified technician to investigate why

the engine did not start.

OPERATING THE TYPE C USB PORT, TYPE

A USB PORT, AND LED LIGHT

The Type C Port, Type A USB Port and LED Light are located on

opposite sides of the unit. They are all controlled by the Power

Button (on the front of the unit). Refer to the “Features” section to

locate.

1. Press the Power Button on the unit once. The Type C Port and

USB port are both ready to use.

2. Lift up the protective cover of the Type C and Type A USB

ports. Plug the USB-powered device into the appropriate USB

power port and operate normally.

English

3. Press the Power Button a second time. The Area Light will turn

on (and the USB Ports remain active).

4. Press the Power Button a third time to turn off both functions.

Periodically check the unit’s battery status. When the battery level is

nearly empty (only one blue Battery Status LED Indicator lights), the

unit must be recharged or the unit’s built-in low voltage protection

will activate briefly before automatic shut down occurs.

Make sure all the unit functions are turn off when the unit is being

recharged or stored.

TYPE C PORT AND TYPE A USB PORT FAULT CONDITIONS

When the Type C and/or Type A USB Ports are in use, the unit will

monitor for the following fault conditions (on both Ports):

• If a Low Battery Voltage Fault occurs, only one Battery

Status LED Indicator flashes for 30 seconds before automatic

shut down occur.

• If an Overload Fault or a Short-circuit occurs, the unit will

automatically shut down immediately.

• If the battery of the unit overheats or is too cold, the

output of the USB ports automatically shut down immediately.

The Battery Status LED indicators light for one minute before

the unit automatically shuts down.

In any of these cases, disconnect the USB-powered device

immediately.

–Make sure the unit does not need to be recharged.

–Allow the unit to cool down for several minutes before attempting

to use the USB Ports again.

–If a fault occurs again, make sure that the total draw of all USB

devices plugged into the USB Ports does not exceed 3.1A (5V).

–If an individual USB device is within specifications and the fault

occurs, have the USB device checked for malfunction and do not

continue to use it with these USB Ports.

Notes: This unit’s USB Ports do not support data communication. They only

provide power to external USB-powered devices. The USB Ports provide a total of

3.1A (5V).

Some USB-powered household electronics may not operate with this USB port.

Check the manual of the corresponding electronic device (including a cell phone,

tablet, etc.) to confirm that it can be used with this type of USB port.

OPERATING THE 120V AC/USB CHARGING

ADAPTER’S USB PORT

Plug the 120V AC/USB Charging Adapter into a (powered) standard

North American 120 volt 60Hz outlet. Simply plug a USB device into

the USB outlet and operate normally.

WARNING – To reduce the risk of injury or property damage:

Always plug the 120V AC/USB charging adapter to the standard

North American 120 volt 60Hz outlet before plugging any devices

into it.

OPERATING THE 12V DC/USB CHARGING

ADAPTER’S USB PORT

Plug the 12V DC/USB Charging Adapter into a vehicle’s 12 volt DC

accessory outlet or other functioning 12 volt DC power source. The

LED indicator on the 12V DC/USB Charging Adapter LED Indicator

will light green to show that it is properly connected. Simply plug a

USB device into the USB outlet and operate normally.

Note: Some vehicles require that the ignition be switched to the

accessory outlet position in order to power the accessory outlet.

Care and Maintenance

WARNING: To reduce the risk of injury, turn the unit off and

disconnect it from any power source before installing and removing

accessories, before adjusting or when performing maintenance. An

accidental start-up can cause injury.

English

Never submerge this unit in water. Dirt and grease may be removed

from the exterior of the unit using a cloth or soft non-metallic brush.

Never let any liquid get inside the unit; never immerse any part of the

unit into a liquid.

WARNING: Shock hazard. Disconnect the 120V AC/USB charging

adapter before cleaning.

Except for the fuse in the 12V DC/USB Charging Adapter, there

are no user-replaceable parts. Periodically inspect the condition of

adapters, connectors and wires. Contact manufacturer to replace any

components that have become worn or broken.

THE INTERNAL BATTERY

All batteries lose energy from self-discharge over time and more rapidly

at higher temperatures. When the unit is not in use, we recommend

that the battery is charged at least every 3-6 months.

BATTERY REPLACEMENT

The battery should last the service life of the unit. Service life is

dependent on a number of factors including but not limited to the

number of recharge cycles, and proper care and maintenance of the

battery by the end user. Contact manufacturer for any information you

may need.

SAFE BATTERY DISPOSAL

Contains a lithium battery, which must be disposed of

properly. Recycling is required. Failure to comply with

local, state and federal regulations can result in fines, or

imprisonment.

Please recycle.

WARNING – To reduce the risk of serious injury or property

damage:

• Do not dispose of the battery in fire as this may result in an explosion.

• Before disposing of the battery, protect exposed terminals with

heavy-duty electrical tape to prevent shorting (shorting can result

in injury or fire).

• Do not expose battery to fire or intense heat as it may explode.

12 VOLT DC/USB ADAPTER PLUG FUSE REPLACEMENT

(OPTIONAL ACCESSORY)

The fuse in the plug end of the 12 Volt DC/USB Adapter protects the

adapter’s charging circuit. If the built-in 120 Volt AC Charger operates,

but the DC charging adapter does not, then this fuse may be opened

(blown).

To replace the fuse:

1. Unscrew the end cap of the DC plug (counterclockwise).

2. Remove spring center contact and fuse.

END CAP

CENTER

CONTACT

2A FUSE

3. Check fuse with a continuity checker.

4. If blown, locate a replacement 2 amp.

5. Replace the fuse, spring, contact and end cap.

6. Screw end cap clockwise until it is finger tight –

DO NOT OVER-TIGHTEN.

7. Test for proper operation of the 12 volt DC

charging adapter.

English

Troubleshooting

Problem Possible Solution

Unit will not charge Check that all the unit functions are

all turned off.

Check that the USB Charging Cable

is properly connected to either the

12V DC/USB charging adapter or the

120V AC/USB charging adapter, and

to the unit.

Check the connection to the AC or

DC power source. Make sure there is

good contact.

Confirm that there is functioning AC

or DC current.

Confirm that the unit is plugged into

a 2A USB power source.

Check the plug fuse in the 12V DC/

USB Charging Adapter. Replace the

fuse following the instructions in this

manual, if necessary.

The unit may have shut down to

protect the battery from overheating

after a long period of operation

or charging. Unplug the charging

adapter from the power source and

disconnect the USB charging cable

from the unit. Allow the unit to cool

down for a period before resuming

charging.

Problem Possible Solution

Unit fails to jump-start Check that all the unit functions are

all turned off.

Make sure a proper polarity cable

connection has been established and

the Bi-Color Booster Status Indicator

on the Smart Cables Controller lights

green.

The unit may be in over-current /

over-time protection. Remove the

clamps and restart after a cooling

down period of approximately 30

minutes.

The unit may be overheated due to

the excessive engine cranking. Make

sure all the unit functions are turned

off and allow the unit to cool down

before resuming operation.

The vehicle battery may in fault

condition and cannot accept starting

assistance. The manufacturer

recommends taking it to a certified

automotive service center for

evaluation.

Check that the unit has a full charge.

Recharge the unit if necessary.

English

Problem Possible Solution

The Type C Port and/

or Type A USB port will

not operate

Make sure the Power Button has

been pressed to turn the USB ports

on.

If a fault condition exists in either

of the USB Ports, the unit will

automatically shut down. Refer to the

“Type C Port and Type A USB Port

Fault Conditions” section and remedy

any faults.

Make sure that the total draw of all

USB devices plugged into the USB

Ports do not exceed 3.1A (5V).

Some USB-powered household

electronics will not operate with these

USB charging/power ports. Check

the manual of the corresponding

electronic device to confirm that it

can be used with this type of USB

charging/power port.

Check that the unit has a full charge.

Recharge the unit if necessary.

The 120V AC/USB

Charging Adapter’s

USB port will not

operate

Make sure you have live AC power to

the outlet the 120V AC/USB Charging

Adapter is plugged into.

Make sure the rating of equipment

plugged into the charging adapter’s

USB port does not exceed 2A

continuous.

Problem Possible Solution

The 120V AC/USB

Charging Adapter’s

USB port will not

operate (Cont)

Some household USB-powered

electronics will not operate with this

USB port. Check the manual of the

corresponding electronic device to

confirm that it can be used with this

type of USB port.

The 12V DC/USB

Charging Adapter’s

USB port will not

operate /

12V DC/USB Charging

Adapter LED Indicator

does not come on

Check the connection to the 12 volt

DC power source. Make sure there is

good contact.

Confirm there is functioning DC

current.

Check the plug fuse in the 12V DC/

USB charging adapter. Replace the

fuse following the instructions in this

manual, if necessary.

Make sure the rating of equipment

plugged into the charging adapter’s

USB port does not exceed 2A

continuous.

Some household USB-powered

electronics will not operate with this

USB port. Check the manual of the

corresponding electronic device to

confirm that it can be used with this

type of USB port.

English

Problem Possible Solution

LED Area Light does

not come on Make sure the Power Button has

been pressed twice to turn the LED

Light on.

Check that the unit has a full charge.

Recharge the unit if necessary.

Accessories

WARNING: Since accessories other than those offered by

DeWALT have not been tested with this product, the use of such

accessories with this unit could be hazardous. To reduce the risk of

injury, only DeWALT recommended accessories should be used with

this product.

If you need assistance regarding accessories, please contact the

manufacturer at 1-888-394-3392 or CustomerService@dewalt12volt.

com.

Service Information

Whether you need technical advice, repair, or genuine factory

replacement parts, contact the manufacturer at 1-888-394-3392 or

[email protected].

One Year Limited Warranty

The manufacturer warrants this product against defects in material and

workmanship for a period of one (1) year from the date of retail purchase

by the original end-user purchaser (“Warranty Period”).

If there is a defect and a valid claim is received within the Warranty

Period, the defective product can be repaired, replaced or refunded,

without charge, in the following ways: (1) Return the product to the

manufacturer for repair, replacement or refund at manufacturer’s option.

Proof of purchase may be required by manufacturer. (2) Return the

product to the retailer where product was purchased for an exchange

(provided that the store is a participating retailer). Returns to retailer

should be made within the time period of the retailer’s return policy for

exchanges only (usually 30 to 90 days after the sale). Proof of purchase

may be required. Please check with the retailer for their specific return

policy regarding returns that are beyond the time set for exchanges.

This warranty does not apply to: accessories, bulbs, fuses and batteries;

defects resulting from normal wear and tear, accidents; damages

sustained during shipping; alterations; unauthorized use or repair;

neglect, misuse, abuse; and failure to follow instructions for care and

maintenance for the product.

This warranty gives you, the original retail purchaser, specific legal rights

and you may have other rights which vary in certain states or provinces.

This product is not intended for commercial use.

90 DAY REFUND POLICY

If you are not completely satisfied with the performance of this product

for any reason, you can return it within ninety (90) days from the date

of purchase with a receipt for a full refund.

Please visit our website www.baccusglobal.com/register to register

your new Baccus Global LLC product and to be kept up to date on

new products and special offers.

Specifications

Jump-Starter / USB Power Bank (Certified to ANSI/CAN/

UL STD. 2743)

Output: *1600 Amp Max.

English

Input: 5V DC, 2A

USB Ports: 5V DC, 3.1A max.

Battery Capacity: Lithium polymer, 11.1V DC

LED Light: 3 white LEDs

Charging Temperature: 32°F to 104°F (0°C to 40°C)

Operating Temperature: –4°F to 104°F (–20°C to 40°C)

12V DC/USB Charging Adapter (Conforms to UL STD.

2089)

Input: 12V DC, 1.1A

Output: 5V DC, 2A

Fuse: 2A

120V AC/USB Charging Adapter (Conforms to UL STD.

62368-1)

Input: 120V AC, 60Hz, 13.3W

Output: 5V DC, 2A

Imported by Baccus Global, LLC,

621 NW 53rd St., Suite 450, Boca Raton, FL 33487

www.dewalt12volt.com 1-888-394-3392

Made in China

DeWALT® and the DeWALT Logo are trademarks of the DeWALT

Industrial Tool Co., or an affiliate thereof and are used under license.

The yellow/black color scheme is a trademark for DeWALT power

tools & accessories.

*1600 Peak Amps: Tested and verified by Intertek. Conforms to UL 2743.

www.dewalt12volt.com

RD080122

La page charge ...

DeWalt DXAELJ16 Le manuel du propriétaire

Marque: DeWalt

Modèle: DXAELJ16

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DXAELJ16 Owner's manual

Documents connexes

DeWalt DXAEJ14CA Le manuel du propriétaire

DeWalt DXAELJ16 Le manuel du propriétaire

DeWalt DXAELJ16 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents