DeWalt DXAELJ16 Le manuel du propriétaire

Taper
Le manuel du propriétaire
40
DXAELJ16CA
LITHIUM AUTOMOTIVE JUMP STARTER WITH USB POWER BANK
BLOC D’ALIMENTATION POUR DÉMARRAGE DE SECOURS
AUTOMOBILE AU LITHIUM AVEC CHARGEUR PORTATIF USB
INSTRUCTION MANUAL
MODE D’EMPLOI MANUAL DE
INSTRUCCIONES
If you have questions or comments, contact us.
Si vous avez des questions ou des commentaires, contactez-nous.
1-888-394-3392
RD080122
English
2
ADVERTENCIA: Lea todas las instrucciones antes de utilizar
el producto. No seguir todas las instrucciones que aparecen a
continuación pueden provocar descargas eléctricas, incendios
y/o lesiones graves.
ADVERTENCIA: Este producto o su cable de alimentación contiene
plomo, una sustancia química reconocida por el Estado de California
como causante de cáncer, defectos de nacimiento u otros problemas
reproductivos. Lávese las manos después de utilizarlo. Para más
información, visite www.P65Warnings.ca.gov
WARNING: Read all instructions before operating product.
Failure to follow all instructions listed below may result in electric
shock, fire and/or serious injury.
WARNING: This product or its power cord contains lead, a chemical
known to the State of California to cause cancer and birth defect or
other reproductive harm. Wash hands after handling. For more
information go to www.P65Warnings.ca.gov
English
3
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal
word. Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which,
if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury
which, if not avoided, may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS
DEWALT TOOL, CALL US TOLL FREE AT: 1-888-394-3392.
Lithium Automotive Jump Starter with
USB Power Bank
The DXAELJ16 1600A Jump Starter and 3.1A USB Ports is a DeWALT
jump starter that features a USB-A & USB-C charging ports.
Important Safety
Instructions
1. Keep these instructions.
2. Heed all warnings.
3. Follow all instructions.
4. Avoid dangerous environments. Don’t use this unit in damp or wet
locations; or in the rain or snow.
5. Clean only with a dry cloth.
6. Keep children away from the work area. Keep this unit away from
children. This is not a toy!
7. Store indoors. When not in use, this unit should be stored indoors
in a dry and high or locked-up place – out of the reach of children.
8. Stay alert. Use common sense. Do not operate this equipment
when you are tired or impaired.
9. Only use attachments/accessories specified by the manufacturer.
The use of any accessory or attachment not recommended for
use with this appliance could be hazardous.
10. Use only on a flat, level surface. If a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
11. To reduce risk of electric shock, disconnect the
unit from any power source before attempting
maintenance or cleaning. Turning off controls
without disconnecting will not reduce this risk.
12. Check for damaged parts. Any part that is damaged should be
properly repaired or replaced by manufacturer unless otherwise
indicated elsewhere in this instruction manual before further
use. Servicing is required when the unit has been damaged in
any way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the unit, the unit has
been exposed to rain or moisture, does not operate normally, or
has been dropped. Do not disassemble the unit; return it to the
manufacturer when service or repair is required.
Opening the unit may result in a risk of electric shock or fire, and
will void warranty. Contact the manufacturer at 1-888-394-3392
for more information.
13. Unit shall not be exposed to dripping or splashing and no objects
filled with liquids, shall be placed on the unit.
14. Do not operate this unit near flammable liquids or in gaseous or
explosive atmospheres.
English
4
15. This unit employs parts (switches, relays, etc.) that produce arcs
or sparks. Therefore, if used in a garage or enclosed area, the
unit MUST be placed not less than 18 inches above the floor.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
NOTICE: Per FCC Part 15, changes or modifications to this equipment
not expressly approved by DEWALT could void your authority to operate
this equipment.
READ ALL INSTRUCTIONS
GENERAL SAFETY WARNINGS AND INSTRUCTIONS
WARNING – To reduce the risk of fire, electric shock:
The Smart Cables Controller and Smart Cables Port are
always “live”! NEVER insert fingers into the sockets or attempt
to disassemble the unit.
Do not put the unit in water or other liquid. Do not place or
store this unit where it can fall or be pulled into water. Do not
expose it to rain, snow or use when wet.
Charge indoors only.
Use only the USB charging cable supplied by the manufacturer
to recharge.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM BATTERIES
WARNING – To reduce the risk of fire, electric shock,
burst hazard, or injury to persons or property: Lithium batteries
are small, compact and ideal for providing long-lasting power to this
unit. However, they must be used and charged properly. Improper
use can result in serious injury, fire, or death.
Lithium batteries can explode in the presence of a source of
ignition. Do not use the product in the presence of an
open flame.
Do not place this lithium battery powered unit in fire or apply
heat to it.
Do not subject this lithium battery powered unit to strong
impacts or shocks. The battery in this unit contains safety and
protection devices which, if damaged, may cause the battery to
generate heat, rupture or ignite.
Do not expose this lithium battery powered unit to water or salt
water, or allow the battery to get wet.
English
5
Avoid storing this lithium battery powered unit in the basement,
bathroom or other areas of the house that are or may become
wet or humid or where moisture may concentrate.
Do not leave this lithium battery powered unit in direct sunlight,
or use or store the unit inside cars in hot weather. Doing so
may cause the battery to generate heat, rupture, or ignite.
Using the battery in this manner may also result in a loss of
performance and a shortened life expectancy.
Never charge this unit near heat or flammable objects.
NEVER THROW WATER ON A BURNING LITHIUM
BATTERY! If a lithium battery does catch on fire, it will burn
even more violently if it comes in contact with water or even
moisture in the air. A fire extinguisher must be used.
Battery Charging and Capacity
This unit is delivered in a partially charged state – you must fully
charge it before using it for the first time.
When stored at room temperature with a full charge, lithium
batteries will begin to discharge from the time they are
manufactured, even when unused. Deep discharges also decrease
their capacity. Battery life can be extended by the following:
Charge battery to full capacity before storage.
Store this unit at temperatures between 5°C and 20°C (41°F
and 68°F).
Never discharge the battery fully.
Charge after each use.
Always charge at least once every 3-6 months if not in frequent
use to prevent overdischarge.
Transportation of Lithium Batteries
Always check all applicable local, national, and international
regulations before transporting a unit containing a lithium battery.
Transporting an end-of-life, damaged, or recalled battery may, in
certain cases, be specifically limited or prohibited.
INSTRUCTIONS PERTAINING TO THE
12V DC/USB CHARGING ADAPTER
CAUTION – To avoid the risk of property damage:
The 12 Volt DC charging adapter must only be connected to
batteries with a nominal output voltage of 12 volts. The unit will
not operate from a 6 volt battery and will sustain permanent
damage if connected to a 24 volt battery.
Always connect the 12 volt DC/USB charging adapter to the 12
volt DC power source before plugging any devices into it.
NEVER connect the 12V DC/USB charging adapter to a
positive grounded vehicle.
Specific Safety Instructions for
Jump Starters
WARNING – Burst hazard: Do not use the unit for charging dry-cell
batteries that are commonly used with home appliances. These
batteries may burst and cause injury to persons and damage property.
Use the unit for boosting a lead-acid battery only. It is not intended to
supply power to a low-voltage electrical system other than in a starter-
motor application.
WARNING: To reduce the risk of electric shock, never immerse this
unit in water or any other liquid, or use when wet.
WARNING – Risk of explosive gases:
Working in the vicinity of a lead acid battery is dangerous. Batteries
generate explosive gases during normal battery operation. For this
reason, it is of the utmost importance that each time before using
the jump-starter you read this manual and follow instructions exactly.
To reduce the risk of battery explosion, follow these instructions and
those published by the battery manufacturer and manufacturer of
English
6
any equipment you intend to use in the vicinity of the battery. Review
cautionary markings on these products and on the engine.
WARNING – To reduce the risk of fire:
Do not operate near flammable materials, dust, fumes or gases.
Do not expose to extreme heat or flames.
CAUTION – To reduce the risk of injury or property damage:
NEVER ATTEMPT TO JUMP-START OR CHARGE A FROZEN
BATTERY.
Make sure the cord is located so that it will not be stepped on, tripped
over or otherwise subjected to damage or stress.
Do not leave the unit unattended while in use.
Pull by the plug rather than the cord when disconnecting the USB
Charging Cable.
Vehicles that have on-board computerized systems may be damaged
if vehicle battery is jump-started. Before jump-starting, read the
vehicle’s owner’s manual to confirm that external-starting assistance
is suitable.
When working with lead acid batteries, always make sure immediate
assistance is available in case of accident or emergency.
Always have protective eyewear when using this product: contact with
battery acid may cause blindness and/or severe burns. Be aware of
first aid procedures in case of accidental contact with battery acid.
Have plenty of fresh water and soap nearby in case battery acid
contacts skin.
Never smoke or allow a spark or flame in vicinity of vehicle battery,
engine or power station.
Stay clear of fan blades, belts, pulleys, and other parts that can
cause injury to persons.
Remove personal metal items such as rings, bracelets,
necklaces and watches when working with a lead acid battery. A
lead acid battery can produce a short circuit current high enough to
weld a ring, or similar metal object, to skin, causing a severe burn.
Do not wear vinyl clothing when jump-starting a vehicle. Friction can
cause dangerous static-electrical sparks.
Do not wear loose clothing or jewelry. They can be caught in
moving parts. Rubber gloves and substantial, non-skid footwear are
recommended when working outdoors. Wear protective hair covering
to contain long hair.
Be extra careful to avoid dropping a metal tool onto the battery. It
might spark or short-circuit the battery or another electrical part and
could cause an explosion.
Jump-start procedures should only be performed in a safe, dry,
well-ventilated area.
Always store battery clamps when not in use. Never touch battery
clamps together.
Make sure to connect the clamps with correct polarity.
Do not expose battery to fire or intense heat since it may explode.
Before disposing of the battery, protect exposed terminals with
heavy-duty electrical tape to prevent shorting (shorting can result
in injury or fire).
Place this unit as far away from the battery as cables permit.
Never allow battery acid to come in contact with this unit.
Do not operate this unit in a closed area or restrict ventilation in any
way.
This system is designed to be used only on vehicles with a 12 volt DC
battery system. Do not connect to a 6 volt or 24 volt battery system.
Excessive engine cranking can damage a vehicle’s starter motor. If
the engine fails to start after the recommended number of attempts,
discontinue jump-start procedures and look for other problems that
may need to be corrected.
Do not use this jump starter on a watercraft. It is not qualified for
marine applications.
English
7
INSTRUCTIONS PERTAINING TO THE
USB PORTS
IMPORTANT:
Some household USB-powered electronics will
not operate with the USB ports provided with this unit and
its charging adapters.
Check the manual of the corresponding electronic devices
(including phones, tablets, etc.) to confirm that they can be used with one of these USB ports and
which USB port to use (Type A or Type C).
The USB ports do not support data communication. They only
provide power to an external USB powered device, as follows:
– 5V DC/3.1A maximum using the Type A and Type C USB ports on the unit;
– 5V DC/2A using the USB ports on the AC/USB or DC/USB Charging Adapters).
Make sure the rating of equipment plugged into the USB port does not exceed the amperage
stated.
Always connect the appropriate charging adapter to either the
120V AC or 12V DC power source before plugging any devices
into it.
Do not attach USB hubs allowing connection of multiple
personal electronic devices to any of the USB ports on the
charging adapters.
Do not insert foreign objects into any of the USB Ports.
FIRST AID
When working with lead acid batteries, always make sure immediate assistance is available in
case of accident or emergency.
Always have protective eyewear when using this product: contact with battery acid may cause
blindness and/or severe burns. Be aware of first aid procedures in case of accidental contact
with battery acid.
Have plenty of fresh water and soap nearby in case battery acid
contacts skin.
Remove personal metal items such as rings, bracelets, necklaces
and watches when working with a lead acid battery. A lead acid
battery can produce a short circuit current high enough to weld
a ring, or similar metal object, to skin causing a severe burn.
Stay clear of fan blades, belts, pulleys, and other parts that can
cause injury to persons.
Be extra cautious to avoid dropping a metal tool onto the
battery. It might spark or short-circuit the battery or another
electrical part, and that may cause an explosion.
Never smoke or allow a spark or flame in vicinity of vehicle
battery, engine or battery charger.
SKIN: If battery acid contacts skin or clothing, wash
immediately with soap and water for at least 10 minutes. If
redness, pain, or irritation occurs, seek immediate medical
attention.
EYES: If battery acid comes in contact with eyes, flush eyes
immediately, for a minimum of 15 minutes and seek immediate
medical attention.
SAVE THESE
INSTRUCTIONS
FOR FUTURE USE
English
8
WARNING – To reduce the risk of injury:
Follow these instructions and
those published by the battery manufacturer and manufacturer of any equipment you intend to use with
this unit. Review cautionary markings on these products and on engine.
INTRODUCTION
Congratulations on purchasing your new Lithium Jump-Starter / Power Bank. Read this
Instruction Manual and follow the instructions carefully before using this unit.
IMPORTANT NOTES:
Several factors can affect a jump-starter’s ability to boost a
vehicle’s battery, including, but not limited to the size of the
battery, the temperature (hot or cold), whether the battery is
damaged or defective, and whether the jump-starter itself is fully
charged.
The jump-starter requires a minimum voltage to detect the
correct connection before it will begin to boost. If the vehicle
battery voltage is below approximately 2 volts, it may not be able
to detect connection and may not be able to start the vehicle.
While this low battery voltage is rare it may occur under extreme
conditions.
English
9
1. USB-A and USB-C Power
Ports
2. 200 Lumen LED Light
3. Power Button
4. LED Status Indicators
5. Smart Cables Controller
6. Metal Battery Clamps
7. DC Charger
8. AC Charger
9. USB Charging Cable
FEATURES
English
10
Viewing Battery Status
The Battery Status LED Indicators indicate the battery charge level
as follows:
If the battery charge level is at full capacity, all three Battery
Status LED Indicators light.
If the battery is at partial charged, two Battery Status LED
Indicators light.
If the battery is nearly empty, only one Battery Status LED
Indicator lights. The unit should be charged at this time.
If the battery is completely empty, only one Battery Status LED
Indicator flashes. The unit MUST be charged at this time or the
unit’s built-in low voltage protection will activate and the unit
will automatically shut down.
CHARGING / RECHARGING
This unit is shipped in a partially charged state. Charge the unit after purchase, before first use, and
after each subseuent use until all three blue Battery Status LED Indicators light when the Power
Button is pressed (with the adapter unplugged from the unit).
IMPORTANT:
When the unit is not in use, we recommend that the battery is charged at
least every 3 to 6 months. Failure to keep the battery charged will cause permanent damage and
result in poor performance.
NOTES:
When the Type A USB port is in use in the charging process,
the Type C port will have no output. Pressing the Power
Button during the charging process will only control the LED
Light.
When the unit battery is fully charged, the charging process will
terminate and the unit will automatically shut down.
A 2A USB is required in order to recharge the unit (2A AC and
DC charging adapters included).
During the charging process, the unit will stop charging if
the battery of the unit is overheated due to extensive use or
recharging. The charging process will automatically resume
after a cool down period.
CHARGING/RECHARGING USING THE 120 VOLT AC/USB
CHARGING ADAPTER
IMPORTANT: Always connect the 120V AC/USB Charging Adapter
to the 120 Volt AC power source (using the USB Charging Cable)
BEFORE connecting it to the unit.
1. Make sure the Power Button is turned off (the Battery Status
LED Indicators are not lit).
2. Insert one end of the USB Charging Cable into the 120V AC/
USB Charging Adapter.
3. Insert the 120V AC/USB Charging Adapter into a standard 120
volt AC wall outlet or a functioning 120 volt AC power source.
4. Lift up the protective cover of the USB ports. Insert the other
end of the USB Charging Cable into the unit’s Type A USB
port.
5. The blue Battery Status LED Indicators will gradually light up (left
to right) to indicate the unit is charging.
6. Charge for approximately 6 hours or until the unit automatically
shuts down.
7. Unplug the 120V AC/USB Charging Adapter from the 120 volt
AC power source, then disconnect the USB Charging Cable
from the 120V AC/USB Charging Adapter, and then from the
unit’s Type A USB port.
8. Press the Power Button to turn the unit on. When all three
blue Battery Status LED Indicators light, the unit battery is fully
charged.
9. Store the 120V AC/USB Charging Adapter and USB Charging
Cable in a safe place.
English
11
CHARGING/RECHARGING USING THE 12V DC/USB
CHARGING ADAPTER
IMPORTANT: Always connect the 12V DC/USB Charging Adapter
to the 12 volt DC power source (using the USB Charging Cable)
BEFORE connecting it to the unit.
1. Make sure the Power Button is turned off (the Battery Status
LED Indicators are not lit).
2. Insert one end of the USB Charging Cable into the 12V DC/
USB Charging Adapter.
3. Insert the 12V DC/USB Charging Adapter into a vehicle’s 12
volt DC accessory outlet or other functioning 12V DC power
source. The LED indicator on the 12V DC/USB Charging
Adapter will light green when it is properly plugged into the 12
volt DC power source.
Note: Some vehicles require that the ignition be switched to
the accessory outlet position in order to power the accessory
outlet.
4. Lift up the protective cover of the USB ports. Insert the other
end of the USB Charging Cable into the unit’s Type A USB
port.
5. The blue Battery Status LED Indicators will gradually light up
(left to right) to indicate the unit is charging.
6. Charge until the unit automatically shuts down. Unplug the 12V
DC/USB Charging Adapter from the 12 volt DC power source,
then disconnect the USB Charging Cable from the 12V DC/
USB Charging Adapter, and then from the unit’s Type A USB
port.
7. Press the Power Button to turn the unit on. When all three
blue Battery Status LED Indicators light, the unit battery is fully
charged.
8. Store the 12V DC/USB Charging Adapter and USB Charging
Cable in a safe place.
CHARGING/RECHARGING USING THE USB CHARGING
CABLE AND A DEVICE WITH A USB POWER PORT (NOT
SUPPLIED)
IMPORTANT: Always connect the USB Charging Cable to the
external device’s USB power port BEFORE connecting it to the unit.
A 2A USB power source is required in order to recharge the unit.
1. Make sure the Power Button is turned off (the Battery Status
LED Indicators are not lit).
2. Insert one end of the USB Charging Cable into an external
device’s functional USB power port.
3. Lift up the protective cover of the USB ports. Insert the other
end of the USB Charging Cable into the unit’s Type A USB
port.
4. When the unit is properly connected, the blue Battery Status
LED Indicators will gradually light up (left to right) to indicate
the unit is charging.
5. Charge until the unit automatically shuts down.
6. Disconnect the USB charging cable from the device’s USB
power port and the unit.
7. Press the Power Button to turn the unit on. When all three
blue Battery Status LED Indicators light, the unit battery is fully
charged.
8. When charging is complete, store the USB Charging Cable in
safe place.
English
12
OPERATING INSTRUCTIONS
JUMP-STARTING USING THE SMART CABLES
Battery Clamp Connection Precautions
Connect and disconnect the battery clamps only after unplugging
the power source.
Make sure the engine is not running when connecting or
disconnecting the battery clamps.
Never allow clamps to touch each other.
Attach clamps to battery and chassis as indicated in the section
“Connecting the Jump-Starter Using the Included Battery
Clamps”.
CONNECTING THE JUMP-STARTER USING THE INCLUDED
BATTERY CLAMPS
1. Position the Smart Cables Controller to reduce risk of damage
by the car hood, doors, or moving engine parts.
2. Stay clear of fan blades, belts, pulleys, and other parts that
can cause injury to persons.
3. Check polarity of battery posts. The positive (POS, P, +) battery
post usually has larger diameter than the negative (NEG, N, –)
post.
4. Connect the Smart Cables Connector to the Smart Cables
Port. Be especially careful, since both the Connector and
Controller are “live.”
5. Connect the positive (RED) clamp from the jump-starter to the
positive (POS, P, +) ungrounded battery post. Connect the
negative (BLACK) clamp to the negative (NEG, N, –) battery
post, the vehicle chassis or engine block away from the
battery. Do not connect the clamp to the carburetor, fuel lines
or sheet-metal body parts. Connect to a heavy gauge metal
part of the frame or engine block.
Note: If the battery clamps are incorrectly connected with
regard to polarity, the Bi-Color Jump-Starter Status Indicator
on the Smart Cables Controller will light red until the clamps
are disconnected. Remove the clamps and then reconnect
them with the correct polarity.
6. When disconnecting the jump-starter, first remove the negative
BLACK (–) clamp from the negative battery post or the vehicle
chassis, and then remove the positive RED (+) clamp from the
positive battery post. Disconnect the double barrel connector
of the Smart Cables Controller from the Smart Cables Port of
unit. Store the Smart Cables Controller in a safe place.
Procedure
Take the following steps, observing all cautions and warnings in the
“Important Safety Instructions” section at the front of this manual.
1. Turn off vehicle ignition and all accessories (radio, A/C, lights,
connected cell phone chargers, etc.). Place vehicle in “park”
and set the emergency brake.
2. Make sure all the unit functions are turned off (the Battery
Status LED Indicators are not lit) and the USB Charging Cable
is NOT connected.
3. Lift up the protective cover of the unit’s Smart Cables Port.
Insert the double-barrel Smart Cables Connector into the
Smart Cables Port on the unit.
4. Set up the unit as described in the “Connecting the Jump-
starter Using Included Battery Clamps” section, observing all
warnings and cautions in the “Important Safety Instructions”
section.
5. When the unit is properly connected, the Bi-Color Status
Indicator on the Smart Cables Controller will light green.
6. Turn on the ignition and crank the engine in 5-6 second bursts
until the engine starts.
English
13
7. When the process is completed, disconnect the jump-starter.
First remove the negative BLACK (–) clamp from vehicle
chassis, and then remove the positive RED (+) clamp from
the positive battery post. Disconnect the double barrel Smart
Cables Connector from the Smart Cables Port.
8. Store the Smart Cables Controller in a safe place.
9. Recharge the unit fully.
IMPORTANT NOTES:
If the battery clamps are incorrectly connected with regard to polarity,
the Bi-Color LED Status Indictor will light red until the clamps are
disconnected. Remove the clamps and then reconnect them with
correct polarity.
If the voltage of the unit’s internal lithium battery is low and has
insufficient output power, the Bi-Color LED Status Indictor will light
red. Disconnect the unit and fully charge following the directions in
the “Charging / Recharging” section.
If the Smart Cables Controller is overheated, the Bi-Color LED
Status Indictor will light red. Disconnect the Battery Clamps and
allow the unit to cool down for a period before resuming any
operation.
If the cranking current and/or time period exceeds the unit’s
parameters, the Bi-Color LED Status Indictor will flash red for
50 seconds (a cooling down period) before lighting green again
(resuming normal operation).
CAUTION – To avoid the risk of property damage:
If the vehicle doesn’t start after the first attempt, allow a resting/
cooling period of 4 to 5 minutes before making asecond attempt.
If a second attempt doesn’t start the vehicle, discontinue use
and look for other problems that need to be corrected. The
battery may be damaged.
NEVER attempt to use the unit to start a vehicle while it is in
charging mode.
Using the jump-starter without a car battery installed in the
vehicle will damage the vehicle’s electrical system.
IMPORTANT: Always turn the unit off when not in use. Recharge this
unit fully after each use.
CAUTION – TO REDUCE THE RISK OF PROPERTY DAMAGE:
Vehicles that have on-board computerized systems may be damaged
if vehicle battery is jump-started. Before jump-starting this type of
vehicle, read the vehicle manual to confirm that external-starting
assistance is advised.
Excessive engine cranking can damage the vehicle‘s starter motor. If
the engine fails to start after the recommended number of attempts,
discontinue jump-start procedure and look for other problems that
need to be corrected.
If vehicle fails to start, turn off the ignition, disconnect the jump-start
system’s leads and contact a qualified technician to investigate why
the engine did not start.
OPERATING THE TYPE C USB PORT, TYPE
A USB PORT, AND LED LIGHT
The Type C Port, Type A USB Port and LED Light are located on
opposite sides of the unit. They are all controlled by the Power
Button (on the front of the unit). Refer to the “Features” section to
locate.
1. Press the Power Button on the unit once. The Type C Port and
USB port are both ready to use.
2. Lift up the protective cover of the Type C and Type A USB
ports. Plug the USB-powered device into the appropriate USB
power port and operate normally.
English
14
3. Press the Power Button a second time. The Area Light will turn
on (and the USB Ports remain active).
4. Press the Power Button a third time to turn off both functions.
Periodically check the unit’s battery status. When the battery level is
nearly empty (only one blue Battery Status LED Indicator lights), the
unit must be recharged or the unit’s built-in low voltage protection
will activate briefly before automatic shut down occurs.
Make sure all the unit functions are turn off when the unit is being
recharged or stored.
TYPE C PORT AND TYPE A USB PORT FAULT CONDITIONS
When the Type C and/or Type A USB Ports are in use, the unit will
monitor for the following fault conditions (on both Ports):
If a Low Battery Voltage Fault occurs, only one Battery
Status LED Indicator flashes for 30 seconds before automatic
shut down occur.
If an Overload Fault or a Short-circuit occurs, the unit will
automatically shut down immediately.
If the battery of the unit overheats or is too cold, the
output of the USB ports automatically shut down immediately.
The Battery Status LED indicators light for one minute before
the unit automatically shuts down.
In any of these cases, disconnect the USB-powered device
immediately.
Make sure the unit does not need to be recharged.
Allow the unit to cool down for several minutes before attempting
to use the USB Ports again.
If a fault occurs again, make sure that the total draw of all USB
devices plugged into the USB Ports does not exceed 3.1A (5V).
If an individual USB device is within specifications and the fault
occurs, have the USB device checked for malfunction and do not
continue to use it with these USB Ports.
Notes: This unit’s USB Ports do not support data communication. They only
provide power to external USB-powered devices. The USB Ports provide a total of
3.1A (5V).
Some USB-powered household electronics may not operate with this USB port.
Check the manual of the corresponding electronic device (including a cell phone,
tablet, etc.) to confirm that it can be used with this type of USB port.
OPERATING THE 120V AC/USB CHARGING
ADAPTER’S USB PORT
Plug the 120V AC/USB Charging Adapter into a (powered) standard
North American 120 volt 60Hz outlet. Simply plug a USB device into
the USB outlet and operate normally.
WARNING – To reduce the risk of injury or property damage:
Always plug the 120V AC/USB charging adapter to the standard
North American 120 volt 60Hz outlet before plugging any devices
into it.
OPERATING THE 12V DC/USB CHARGING
ADAPTER’S USB PORT
Plug the 12V DC/USB Charging Adapter into a vehicle’s 12 volt DC
accessory outlet or other functioning 12 volt DC power source. The
LED indicator on the 12V DC/USB Charging Adapter LED Indicator
will light green to show that it is properly connected. Simply plug a
USB device into the USB outlet and operate normally.
Note: Some vehicles require that the ignition be switched to the
accessory outlet position in order to power the accessory outlet.
Care and Maintenance
WARNING: To reduce the risk of injury, turn the unit off and
disconnect it from any power source before installing and removing
accessories, before adjusting or when performing maintenance. An
accidental start-up can cause injury.
English
15
Never submerge this unit in water. Dirt and grease may be removed
from the exterior of the unit using a cloth or soft non-metallic brush.
Never let any liquid get inside the unit; never immerse any part of the
unit into a liquid.
WARNING: Shock hazard. Disconnect the 120V AC/USB charging
adapter before cleaning.
Except for the fuse in the 12V DC/USB Charging Adapter, there
are no user-replaceable parts. Periodically inspect the condition of
adapters, connectors and wires. Contact manufacturer to replace any
components that have become worn or broken.
THE INTERNAL BATTERY
All batteries lose energy from self-discharge over time and more rapidly
at higher temperatures. When the unit is not in use, we recommend
that the battery is charged at least every 3-6 months.
BATTERY REPLACEMENT
The battery should last the service life of the unit. Service life is
dependent on a number of factors including but not limited to the
number of recharge cycles, and proper care and maintenance of the
battery by the end user. Contact manufacturer for any information you
may need.
SAFE BATTERY DISPOSAL
Contains a lithium battery, which must be disposed of
properly. Recycling is required. Failure to comply with
local, state and federal regulations can result in fines, or
imprisonment.
Please recycle.
WARNING – To reduce the risk of serious injury or property
damage:
Do not dispose of the battery in fire as this may result in an explosion.
Before disposing of the battery, protect exposed terminals with
heavy-duty electrical tape to prevent shorting (shorting can result
in injury or fire).
Do not expose battery to fire or intense heat as it may explode.
12 VOLT DC/USB ADAPTER PLUG FUSE REPLACEMENT
(OPTIONAL ACCESSORY)
The fuse in the plug end of the 12 Volt DC/USB Adapter protects the
adapter’s charging circuit. If the built-in 120 Volt AC Charger operates,
but the DC charging adapter does not, then this fuse may be opened
(blown).
To replace the fuse:
1. Unscrew the end cap of the DC plug (counterclockwise).
2. Remove spring center contact and fuse.
END CAP
CENTER
CONTACT
2A FUSE
3. Check fuse with a continuity checker.
4. If blown, locate a replacement 2 amp.
5. Replace the fuse, spring, contact and end cap.
6. Screw end cap clockwise until it is finger tight –
DO NOT OVER-TIGHTEN.
7. Test for proper operation of the 12 volt DC
charging adapter.
English
16
Troubleshooting
Problem Possible Solution
Unit will not charge Check that all the unit functions are
all turned off.
Check that the USB Charging Cable
is properly connected to either the
12V DC/USB charging adapter or the
120V AC/USB charging adapter, and
to the unit.
Check the connection to the AC or
DC power source. Make sure there is
good contact.
Confirm that there is functioning AC
or DC current.
Confirm that the unit is plugged into
a 2A USB power source.
Check the plug fuse in the 12V DC/
USB Charging Adapter. Replace the
fuse following the instructions in this
manual, if necessary.
The unit may have shut down to
protect the battery from overheating
after a long period of operation
or charging. Unplug the charging
adapter from the power source and
disconnect the USB charging cable
from the unit. Allow the unit to cool
down for a period before resuming
charging.
Problem Possible Solution
Unit fails to jump-start Check that all the unit functions are
all turned off.
Make sure a proper polarity cable
connection has been established and
the Bi-Color Booster Status Indicator
on the Smart Cables Controller lights
green.
The unit may be in over-current /
over-time protection. Remove the
clamps and restart after a cooling
down period of approximately 30
minutes.
The unit may be overheated due to
the excessive engine cranking. Make
sure all the unit functions are turned
off and allow the unit to cool down
before resuming operation.
The vehicle battery may in fault
condition and cannot accept starting
assistance. The manufacturer
recommends taking it to a certified
automotive service center for
evaluation.
Check that the unit has a full charge.
Recharge the unit if necessary.
English
17
Problem Possible Solution
The Type C Port and/
or Type A USB port will
not operate
Make sure the Power Button has
been pressed to turn the USB ports
on.
If a fault condition exists in either
of the USB Ports, the unit will
automatically shut down. Refer to the
“Type C Port and Type A USB Port
Fault Conditions” section and remedy
any faults.
Make sure that the total draw of all
USB devices plugged into the USB
Ports do not exceed 3.1A (5V).
Some USB-powered household
electronics will not operate with these
USB charging/power ports. Check
the manual of the corresponding
electronic device to confirm that it
can be used with this type of USB
charging/power port.
Check that the unit has a full charge.
Recharge the unit if necessary.
The 120V AC/USB
Charging Adapter’s
USB port will not
operate
Make sure you have live AC power to
the outlet the 120V AC/USB Charging
Adapter is plugged into.
Make sure the rating of equipment
plugged into the charging adapter’s
USB port does not exceed 2A
continuous.
Problem Possible Solution
The 120V AC/USB
Charging Adapter’s
USB port will not
operate (Cont)
Some household USB-powered
electronics will not operate with this
USB port. Check the manual of the
corresponding electronic device to
confirm that it can be used with this
type of USB port.
The 12V DC/USB
Charging Adapter’s
USB port will not
operate /
12V DC/USB Charging
Adapter LED Indicator
does not come on
Check the connection to the 12 volt
DC power source. Make sure there is
good contact.
Confirm there is functioning DC
current.
Check the plug fuse in the 12V DC/
USB charging adapter. Replace the
fuse following the instructions in this
manual, if necessary.
Make sure the rating of equipment
plugged into the charging adapter’s
USB port does not exceed 2A
continuous.
Some household USB-powered
electronics will not operate with this
USB port. Check the manual of the
corresponding electronic device to
confirm that it can be used with this
type of USB port.
English
18
Problem Possible Solution
LED Area Light does
not come on Make sure the Power Button has
been pressed twice to turn the LED
Light on.
Check that the unit has a full charge.
Recharge the unit if necessary.
Accessories
WARNING: Since accessories other than those offered by
DeWALT have not been tested with this product, the use of such
accessories with this unit could be hazardous. To reduce the risk of
injury, only DeWALT recommended accessories should be used with
this product.
If you need assistance regarding accessories, please contact the
manufacturer at 1-888-394-3392 or CustomerService@dewalt12volt.
com.
Service Information
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the manufacturer at 1-888-394-3392 or
One Year Limited Warranty
The manufacturer warrants this product against defects in material and
workmanship for a period of one (1) year from the date of retail purchase
by the original end-user purchaser (“Warranty Period”).
If there is a defect and a valid claim is received within the Warranty
Period, the defective product can be repaired, replaced or refunded,
without charge, in the following ways: (1) Return the product to the
manufacturer for repair, replacement or refund at manufacturer’s option.
Proof of purchase may be required by manufacturer. (2) Return the
product to the retailer where product was purchased for an exchange
(provided that the store is a participating retailer). Returns to retailer
should be made within the time period of the retailer’s return policy for
exchanges only (usually 30 to 90 days after the sale). Proof of purchase
may be required. Please check with the retailer for their specific return
policy regarding returns that are beyond the time set for exchanges.
This warranty does not apply to: accessories, bulbs, fuses and batteries;
defects resulting from normal wear and tear, accidents; damages
sustained during shipping; alterations; unauthorized use or repair;
neglect, misuse, abuse; and failure to follow instructions for care and
maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights
and you may have other rights which vary in certain states or provinces.
This product is not intended for commercial use.
90 DAY REFUND POLICY
If you are not completely satisfied with the performance of this product
for any reason, you can return it within ninety (90) days from the date
of purchase with a receipt for a full refund.
Please visit our website www.baccusglobal.com/register to register
your new Baccus Global LLC product and to be kept up to date on
new products and special offers.
Specifications
Jump-Starter / USB Power Bank (Certified to ANSI/CAN/
UL STD. 2743)
Output: *1600 Amp Max.
English
19
Input: 5V DC, 2A
USB Ports: 5V DC, 3.1A max.
Battery Capacity: Lithium polymer, 11.1V DC
LED Light: 3 white LEDs
Charging Temperature: 32°F to 104°F (0°C to 40°C)
Operating Temperature: 4°F to 104°F (–20°C to 40°C)
12V DC/USB Charging Adapter (Conforms to UL STD.
2089)
Input: 12V DC, 1.1A
Output: 5V DC, 2A
Fuse: 2A
120V AC/USB Charging Adapter (Conforms to UL STD.
62368-1)
Input: 120V AC, 60Hz, 13.3W
Output: 5V DC, 2A
Imported by Baccus Global, LLC,
621 NW 53rd St., Suite 450, Boca Raton, FL 33487
www.dewalt12volt.com 1-888-394-3392
Made in China
Copyright © 2022 Baccus Global, LLC.
DeWALT® and the DeWALT Logo are trademarks of the DeWALT
Industrial Tool Co., or an affiliate thereof and are used under license.
The yellow/black color scheme is a trademark for DeWALT power
tools & accessories.
*1600 Peak Amps: Tested and verified by Intertek. Conforms to UL 2743.
www.dewalt12volt.com
RD080122
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

DeWalt DXAELJ16 Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues