Meyer Sound Portable Speaker CQ-2 Manuel utilisateur

Marque: Meyer Sound

Modèle: Portable Speaker CQ-2

Catégorie: Amplificateur d'instruments de musique

Taper: Manuel utilisateur

Ce manuel convient également à

Patents Pending

The CQ™ Series self-powered loudspeakers contain

independent amplifier and control electronics for one

15” bass-reflex cone driver and one 4” diaphragm horn

driver in a compact enclosure. This integrated design

eliminates amplifier racks, simplifies setup and

installation, and improves durability and reliability.

The CQ Series, consisting of the CQ-1 (low Q) and

CQ-2 (high Q), are efficient full-range speakers and

ideal companions for the PSW-2, PSW-4, and 650-P

self-powered subwoofers. The CQ Series have the

following acoustical specifications:

Frequency Response ±4 dB 40 Hz – 18 kHz

Phase Response ±90° 50 Hz – 16 kHz

Max Peak SPL at 1 m CQ-1: 136 dB; CQ-2: 139 dB

Dynamic Range > 110 dB

The CQ is phase-corrected through the crossover, which

yields exceptional system impulse response and

accurate signal reproduction.

The beam width of a horn is the angle at which the

sound pressure at a given frequency decreases to half

(–6 dB) its on-axis value. Most horns have a beam width

that varies with respect to frequency, nonuniform

frequency response within their coverage area, and

significant side lobes outside their beam width. These

undesirable characteristics are easily identified by

viewing polar patterns plotted at various frequencies.

Meyer Sound developed the CQ Series horns in an

anechoic chamber by measuring coverage patterns

using angular and frequency resolutions of 1° and

⁄24 octave, respectively. The CQ Series horns exhibit

Constant Q: the beam width remains consistent across

the horn’s operating frequency range in both the vertical

and horizontal planes. The CQ-1 has a wider horizontal

beam width than the CQ-2. The CQ Series have the

same vertical beam width and share the following

remarkable attributes:

• uniform frequency response within the beam width

• rapid and uniform amplitude attenuation for all

frequencies outside the beam width

• minimal side lobes

The CQ horns are an unprecedented development in

acoustical measurement, design, and manufacturing.

The CQ Series loudspeakers are ideally suited for venues

requiring precise coverage with minimal interaction

between subsystems but are appropriate for any

acoustical environment.

The CQ can be equipped to operate with the Remote

Monitoring System™ (RMS) interface network and

software application. RMS displays signal and power

levels, driver and cooling fan status, limiter activity, and

amplifier temperature for all speakers in the network on

a Windows-based PC.

• Wide and narrow overage patterns

for CQ-1 (low Q) and CQ-2 (high Q)

• Self-contained control electronics,

amplifiers, and drivers

• Dual-channel 1240 Watt amplifier

(620 Watts per channel)

• Active balanced input circuit

• Active crossover with optimized

pole-zero filter combinations

• Intelligent AC™ System

• TruPower™ Limiting (TPL)

• Compatible with the Remote

Monitoring System™ (RMS)

Features

Operating Instructions

Series

Self-Powered Loudspeaker

™

Pour indiquer les risques

résultant de tensions

dangereuses

Zu die gefahren von

gefährliche spanning zeigen

Important operating

instructions

Pour indequer important

instructions

Zu wichtige betriebs-

anweisung und unter-

haltsanweisung zeigen

Frame or chassis

Masse, châssis

Rahmen oder chassis

Protective earth ground

Terre de protection

Die schutzerde

Para indicar azares provengo

de peligroso voltajes

Para indicar importante

funcionar y mantenimiento

instrucciones

Armadura o chassis Tierra proteccionista

These symbols indicate important safety or operating features in this booklet and on the chassis.

Meyer Sound Laboratories, Inc.

2832 San Pablo Avenue

Berkeley, California 94702

Telephone:510 - 486 - 1166

FAX: 510 - 486 - 8356

E-mail: [email protected]

http://www.meyersound.com

Made by Meyer Sound, Berkeley, CA, USA

European Office:

Meyer Sound Germany

GmbH

Carl Zeiss Strasse 13

56751 Polch, Germany

®®

LISTED

3K59

COMMERCIAL

AUDIO SYSTEM

Meyer Sound Germany

Gmbh

Carl Zeiss Strasse 13

56751 Polch, Germany

Telephone: 49.2654.9600.58

FAX: 49.2654.9600.59

Dangerous voltages:

risk of electric shock

Symbols Used

According to ISO/IEC Guide and EN 45014

Declaration of Conformity

Contact Information

The product herewith complies with the require-

ments of the Low Voltage Directive 73/23/EEC and

the EMC Directive 89/336/EEC.

declares that the product:The Manufacturer:

Product Name: CQ-1, CQ-2

Product Options: All

Name: Meyer Sound Laboratories

Address: 2832 San Pablo Avenue

Berkeley, California 94702-2204, USA

conforms to the following Product Specifications:

Safety: EN 60065: 1994

EMC: EN 55022: 1987 - Class A

IEC 801-2: 1984 - 8 kV

IEC 801-3: 1984 - 3 V/m

IEC 801-4: 1984 - 0.5 kV Signal Lines,

Office of Quality Manager

Berkeley, California USA

October 1, 1996

1.0 kV Power Lines

Shock: 30 g 11 msec half-sine

on each of 6 sides

Vibration: 10 – 55 Hz (0.010 m

peak-to-peak excursion)

Operating temperature:0° C to +45° C

Nonoperating temp: < –40° C or > +75° C

Humidity: to 95% at 35°C

Operating altitude: to 4600 m (15,000 ft)

Nonoperating altitude: to 6300 m (25,000 ft)

Environmental Specifications for

Meyer Sound Electronics Products

Controls and Connectors .................................. 3

Dimensions ........................................................ 3

AC Power ........................................................... 4

Audio Input ........................................................ 5

Limiting and Protection Circuitry ..................... 6

Rigging ............................................................... 7

Complete Systems .............................................. 8

Verifying Polarity ............................................... 10

Coverage Angles and Polar Plots..................... 11

Array Design ...................................................... 14

Safety Summary................................................ 15

Specifications .................................................... 16

Contents

ATENCIÓN

ACCESO INTE

AUTORIZADO A PERSONAL

ACHTUNG

GEHÄUSE NIC

UND REPARATUR NUR DURC

ATTENTION

ENTRETIEN

INTERNES NE SONT AUTORI

PERSONNEL TECHNIQUE QU

UK WARNING

THIS APPA

NO OPERATOR SERVICEABLE

REFER SERVICING TO QUALIFI

WARNINGS:

THIS PRODUCT M

This surface may reach high t

To ensure proper operation, allo

clearance from this surface and

To reduce the risk of electric sh

No operator serviceable parts in

Refer servicing to qualified pers

To reduce the risk of fire or elec

do not expose this appliance to

Meyer Sound, B

Loop

Input

PUSH

Network

Service

Wink

Reset

Activity

Remote Monitor System

10A RMS

20A Peak

88-127V

50-60Hz

700W RMS MAX

Operational voltag

Turn on 80V

Turn on 160V

Auto-Voltage Sele

Controls and Connectors

European Rear User Panel

with IEC 309 connector

Dimensions

15.25"

13.55"

21.0"

20.5"

2.0"

9.55"

30.0"

21.0"

Front Side Top

All units in inches

20.50"

9.55"

14.26"

2.0"

Rear User Panel shown with the optional

Remote Monitoring System (RMS) panel

ATENCIÓN

ACCESO INTERNO SOLO

AUTORIZADO A PERSONAL TÉCNICO CALIFICADO

ACHTUNG

GEHÄUSE NICHT ÖFFNEN WARTUNG

UND REPARATUR NUR DURCH ELEKTROFACHKRÄFTE

ATTENTION

ENTRETIEN ET REPARATIONS

INTERNES NE SONT AUTORISEES QU'AU

PERSONNEL TECHNIQUE QUALIFIÉ

UK WARNING

THIS APPARATUS MUST BE EARTHED.

NO OPERATOR SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED PERSONNEL

WARNINGS:

THIS PRODUCT MUST BE GROUNDED

This surface may reach high temperatures while in use.

To ensure proper operation, allow at least 6 inches

clearance from this surface and adequate ventilation.

To reduce the risk of electric shock do not remove cover.

No operator serviceable parts inside.

Refer servicing to qualified personnel.

To reduce the risk of fire or electric shock

do not expose this appliance to rain or moisture.

Meyer Sound, Berkeley, CA. USA

Loop

Input

PUSH

Active / Speaker Fault

2 +

3 +

10K

Ω

Balanced

Input Polarity

LO Limit

HI Limit

Network

Service

Wink

Reset

Activity

Remote Monitoring System

Earth / Chassis

Case

220K

Ω

ESD

Mains circuit

breakers

Signal input and

loop connectors

Power LED (green/red)

Input polarity switch

Low Limit (red)

High Limit (red)

Tie-wrap anchor

Mains AC inlet

Remote Monitoring

System panel

(if RMS is installed)

95-125V

50-60Hz

1400W RMS MAX

208-235V

50-60Hz

1400W RMS MAX

Auto-Voltage Select

AC Power

The AC voltage operating ranges for the CQ Series are

85–134 V and 165–264 V, at 50 or 60 Hz. The CQ Series

performs surge suppression for high voltage transients

and can safely withstand voltages up to 275 VAC.

Continuous voltages above 275 VAC may

damage the unit!

The Intelligent AC power supply protects the drivers

and amplifier components when an AC source is applied

to the CQ by

• auto-selecting the voltage;

• performing surge suppression and minimizing

inrush current;

• filtering EMI.

After three seconds, the main power supply is slowly

ramped on. The CQ Series uses a NEMA L6-20P or

IEC 309 male power inlet and satisfies UL, CSA, and

EC safety standards.

Use the following AC cable wiring diagram to create

international or special-purpose power connectors:

brown = hot

blue =

neutral

yellow/green =

earth ground

(chassis)

AC cable color code

If the colors referred to in the diagram don't correspond

to the terminals in your plug, use the following

guidelines:

• Connect the blue wire to the terminal marked

with an N or colored black.

• Connect the brown wire to the terminal marked

with an L or colored red.

• Connect the green and yellow wire to the

terminal marked with an E (or ) or colored

green (or green and yellow).

Power Requirements

The CQ presents a dynamic load to the AC mains which

causes the amount of current to fluctuate between quiet

and loud operating levels. Since different types of

cables and circuit breakers heat up at varying rates, it

is essential to understand the types of current ratings

and how they correspond to circuit breaker and cable

specifications.

The maximum continuous RMS current is the maximum

RMS current in a period of at least 10 seconds. It is

used to calculate the temperature increase in cables,

which is used to select cables that conform to electrical

code standards. It is also used to select the rating for

slow-reacting thermal breakers.

The maximum burst RMS current is the maximum

RMS current in a period of approximately 1 second. It

is used to select the rating for most magnetic breakers.

The maximum peak current during burst is used to

select the rating for fast-reacting magnetic breakers

and to calculate the peak voltage drop in long AC

cables according to the formula

Vpk

drop

= Ipk x Total Cable Resistance

Use the table below as a guide to select cables and

circuit breakers with appropriate ratings for your

operating voltage.

sgnitaRtnerruCseireSQC

V511 V032 V001

SMRsuounitnoC.xaM

SMR

A01

SMR

SMRtsruB.xaM

A51

SMR

A81

SMR

tsruBgniruDkaeP.xaM

A22

KAEP

A11

KAEP

A52

KAEP

The minimum electrical service amperage required by

a system of CQs is the sum of the maximum continuous

RMS current for each speaker. We recommend allowing

an additional 30% above the minimum amperage to

prevent peak voltage drops at the service entry.

Safety Issues

Pay close attention to these important electrical and

safety issues.

Use a power cord adapter to drive the CQ from a

standard 3-prong outlet (NEMA 5-15R; 125 V max).

earth

ground

chassis

ground

The CQ requires a grounded outlet. Always use

a grounding adapter when connecting to

ungrounded outlets.

Do not use a ground-lifting adapter or cut the AC

cable ground pin.

Keep all liquids away from the CQ to avoid hazards

from electrical shock.

Do not operate the unit if the power cables are frayed

or broken.

Tie-wrap anchors on the amplifier chassis provide

strain relief for the power and signal cables. Insert the

plastic tie-wraps through the anchors and wrap them

around the cables.

Audio Input

The CQ presents a 10 kΩ input impedance to a three-pin

XLR connector wired with the following convention:

Pin 1 — 220 kΩ to chassis and earth ground (ESD clamped)

Pin 2 — Signal

Pin 3 — Signal

Case — Earth (AC) ground and chassis

Pins 2 and 3 carry the input as a differential signal;

their polarity can be reversed with the input polarity

switch on the user panel. If the switch is in the up

position, pin 2 is hot relative to pin 3, resulting in a

positive pressure wave when a positive signal is applied

to pin 2. Use standard audio cables with XLR connectors

for balanced signal sources.

Shorting an input connector pin to the case

can form a ground loop and cause hum.

A single source can drive multiple CQs with a paralleled

input loop, creating an unbuffered hardwired loop

connection. Make certain that the source equipment

can drive the total load impedance presented by the

paralleled input circuit. For example, since the input

impedance of a single CQ is 10 kΩ, cascading 20 CQs

produces a balanced input impedance of 500 Ω. If a

150 Ω source is used, the 500 Ω load results in a 2.28 dB

loss.

Troubleshooting

If the Active lamp does not light after connection to an

AC source for three seconds, the problem is probably in

the power supply. In the unlikely case that the circuit

breakers trip (the white center buttons pop out), the

amplifier or power supply may be malfunctioning.

Do not reset the breakers! Contact Meyer Sound for repair

information.

If abnormal noise (hum, hiss, popping) is produced

from the loudspeaker, disconnect the audio source

from the speaker. If the noise stops, then the problem

is not within the loudspeaker; check your audio and

AC power sources.

If problems persist, contact Meyer Sound. If repairs

are necessary, the CQ’s modular components are easy

to remove and ship.

Differential Inputs

Limiting and Protection

Circuitry

TruPower Limiting

™

System

Conventional limiters assume that the resistance of a

speaker remains constant and set the limiting threshold

by measuring voltage only. This method is inaccurate

because the speaker’s resistance changes in response

to the frequency content of the source material and

thermal variations in the speaker’s voice coil and magnet.

Conventional limiters begin limiting prematurely,

which under-utilizes system headroom and deprives

the speaker of its full dynamic range.

The TruPower Limiting (TPL) system accounts for

varying speaker impedance by measuring current, in

addition to voltage, to compute the power dissipation

and voice coil temperature. TPL

• allows the speaker to deliver its highest SPL

across its entire frequency range during limiting;

• eliminates long-term power compression when

operated at high levels for extended periods;

• protects the drivers and extends the lifetime of

amplifier and driver components.

Hi Limit and Lo Limit LEDs on the user panel indicate

TPL activity for the high and low frequency drivers,

respectively. The limiters for each driver function

independently and do not affect the signal when the

LEDs are inactive. Limiting begins when the driver

temperature exceeds the maximum safe level and

ceases when the temperature returns to normal.

The CQ performs within its acoustical specifications

and operates at a normal temperature if the limit LEDs

are on for no longer than two seconds, and off for at

least one second. If the LEDs remain on for longer

than three seconds, the CQ is hard limiting with the

following negative consequences:

• Increasing the input level will not increase the

volume.

• The system distorts due to clipping and

nonlinear driver operation.

• Unequal limiting between the low and high

frequency drivers alters the frequency response.

• Driver and amplifier components are subjected

to maximum heat, which shortens their life span.

Troubleshooting with TPL

The TPL LEDs can indicate serious driver problems, if

interpreted correctly. If one CQ in a system exhibits

substantially more TPL activity than others receiving the

same audio signal, then the driver corresponding to

the excessively active LED may have a short circuit. This

is a potentially dangerous condition for the electronics;

shut the CQ down immediately.

The TPL circuit does not activate if there is no power

dissipation in the driver, regardless of the input signal

level. Therefore, if all CQs in a system receiving the same

audio signal exhibit TPL activity except one, then that

unit may have an open voice coil; disconnect it and

contact Meyer Sound for repair information.

TPL can indicate an imbalance in a configuration of

speakers by functioning like a spectrum analyzer. If the

speakers in a subwoofer, mid-bass, or mid-hi subsystem

begin to limit before reaching the required operating

level for the entire system, then that subsystem needs to

be supplemented with additional speakers.

NOTE: Although the TPL limiters exhibit smooth sonic

characteristics, we do not recommend using them for

intentional compression effects. Use an outboard

compressor/limiter to compress a mixed signal.

Fans and Cooling System

The CQ uses a forced-air cooling system with two fans

to prevent the amplifiers from overheating. A variable-

speed primary fan runs continuously with an inaudible

operating noise of 22 dBA at 1 m at its slowest speed.

The speed of the primary fan begins increasing when

the temperature of the heatsinks reaches 42°C. The

fan reaches full speed at 62°C and is barely audible near

the cabinet, even without an audio signal.

In the unusual event that the temperature reaches

74°C, the secondary fan turns on and is clearly audible.

The secondary fan turns on in response to

• primary fan failure (check its status immediately);

• high source levels for a prolonged period in hot

temperatures or direct sunlight;

• driver failure.

The secondary fan turns off when the temperature

decreases to 68°C.

In the highly unlikely event that the secondary fan

does not keep the temperature below 85°C, the CQ

automatically shuts down until AC power is removed

and reapplied. If the CQ shuts down again after cooling

and reapplying AC power, contact Meyer Sound for

repair information.

The fans draw air in through ducts on the front of the

cabinet, over the heatsinks, and out the rear of the

cabinet. Since dust does not accumulate in the amplifier

circuitry, its life span is increased significantly. Make

sure that the air ducts are clear and that there is at

least 6 inches clearance for exhaust behind the cabinet.

air

cooling

fans

heatsinks

power

supply

A foam insert filter, in combination with the entire

front grill surface, acts as an air filter for the cooling

system. Despite the filtering, extensive use or a dusty

operating environment can allow dust to accumulate

along the path of the airflow, preventing normal cooling.

We recommend periodically removing the grill, filter,

and amplifier module and using compressed air to

clear dust from the grill, filter, fans, and heatsinks.

Rigging

The maximum recommended load for a CQ with air-

craft pan fittings is 500 lb (228kg). This working load

is one-fifth the cabinet’s breaking strength. The CQ

has two rigging brackets on both the top and bottom

of the cabinet; each bracket is capable of supporting

the full working load of the cabinet.

rigging brackets

(two on top, two on bottom)

Handles are for carrying only.

Do not use them for rigging!

There are four types of interchangeable rigging brackets,

each fastened by six Phillips screws:

• aircraft pan fittings (ring and stud)

•

/8”-16 nut plates

• M-10 x 1.5 metric nut plates

• blank plates (if no rigging brackets are requested)

NOTE: Units with nut plates are rated for the weight of

one cabinet only.

Rigging load ratings assume a straight tensile pull and

that the cabinet is in new condition with aircraft pan

fittings. If these conditions are not met, the load ratings

can be reduced significantly. Load ratings can also be

reduced by age, wear, and damage. It is important to

inspect the rigging hardware regularly and replace

worn or damaged components immediately.

The standard model should not be installed outdoors

without weather protection. The cabinet, exposed

electronic circuitry, and drivers can all receive weather

protection treatment that allows the unit to be used

safely in wet conditions. Contact Meyer Sound for

information about weather-protected units.

NOTE: All Meyer Sound products must be used in

accordance with local, state, federal, and industry

regulations. It is the owner’s and/or user’s responsibility

to evaluate the reliability of any rigging method for

their application. Rigging should be done only by

experienced professionals.

Complete Systems

Speaker Placement and Polarity

The cabinets in the following example configurations

are in a close-proximity coplanar orientation, unless

otherwise stated. Placing the mid-hi speaker more

than 5 feet from the subwoofer may require setting the

speakers to opposite polarities to compensate for the

propagation delay between them.

In a coplanar orientation, externally amplified Meyer

subwoofers require the opposite polarity setting to

all Meyer self-powered speakers.

We recommend using the Meyer SIM® System II

Sound Analyzer and CP-10 Parametric Equalizer to

• assist the process of configuring and placing

speakers in a system;

• measure propagation delays to set the correct

polarity between speakers;

• measure and equalize variations in frequency

response caused by the acoustical environment

and the placement and interaction of speakers.

Contact Meyer Sound for assistance with your

application.

The LD-1A Line Driver

We recommend using the Meyer LD-1A Line Driver

to integrate different types of Meyer self-powered

speakers into a full-range system. The LD-1A maintains

signal integrity for long cable paths, has two channels

equipped to control a main system, and six auxiliary

channels for down-fill, front-fill, and delay systems. The

LD-1A provides these useful functions:

• The Lo Cut switch activates a high-pass filter

(160 Hz, –12 dB/oct, Q = 0.8) that performs a

crossover function for the Mid-Hi output.

• The Array EQ switch activates a filter (6 dB cut

at 220 Hz, 0.6 octave bandwidth) to equalize

groups of 3 to 5 horizontally arrayed MSL-4s.

• The DS-2 & Sub Crossover switch activates a

crossover network that sends frequencies below

80 Hz to the Sub output, and above 80 Hz to the

DS-2 output. With the switch out, a full-range

signal is sent to the DS-2 and Sub outputs.

• The DS-2 φ and Sub φ switches toggle the polarity

for the DS-2 and Sub outputs.

• The Mid-Hi, DS-2, and Sub outputs each have

their own gain control and mute switch.

Meyer Speaker Types

The following Meyer speakers will be mentioned in

the example applications.

MSL-4: Self-powered mid-hi speaker

DS-2P: Self-powered mid-bass speaker

650-P, PSW-2,

PSW-4: Self-powered subwoofers

650-R2, MSW-2,

USW-1: Externally amplified subwoofers

The self-powered speakers listed above have a loop

connection to send the input signal to another speaker.

CQ and 650-P

The CQ is particularly well matched with the 650-P and

also performs efficiently with the PSW-2 and PSW-4.

Due to the overlap in frequency response between

the CQ and the subwoofer, the system frequency

response contains a rise in the range 40–120 Hz. It is

important to emphasize that the speakers are in phase

in this region. The rise can be corrected using the Meyer

CP-10 Parametric Equalizer, if desired.

650-P

CQ-1 or

CQ-2

loop

input

CP-10 EQ

(1 Channel)

Set the CQ and 650-P to the same polarity.

CQ and 650-R2

Although it is preferable to use the CQ in a completely

self-powered system, excellent results can still be

achieved using the 650-R2, USW-1, and MSW-2.

650-R2

subwoofer

loop

input

CQ-1 or

CQ-2

CP-10 EQ

(1 Channel)

B-2EX

CEU

Amplifier

Set the CQ and the 650-R2‘s amplifier to opposite

polarities.

LD-1A with CQ and 650-P

Activating the Lo Cut filter on the LD-1A for the Mid-Hi

output also eliminates the low frequency rise caused

by the overlap between the CQ and 650-P. Although a

typical CQ : 650-P ratio is 2:1, separate Sub and Mid-Hi

level controls on the LD-1A allow the ratio to vary

while maintaining control of the spectral balance of

the system.

650-P

CQ-1 or

CQ-2

LD-1A

Line Driver

Sub

Mid-hi

Set the CQ and 650-P to the same polarity.

LD-1A with Flown MSL-4, DS-2P, and CQ;

650-P on the Floor

This example shows the LD-1A integrating a complete

system of speakers appropriate for a large venue.

Although channels 1, 3, and 5 constitute half of a

complete system, channels 2, 4, and 6 can be used

with identical connections to create the other half of

the system. The MSL-4 mid-hi, DS-2P mid-bass, and

CQ down-fill speakers are flown; the 650-P subwoofers

are on the floor.

The Mid-Hi and CH 3 outputs drive the inner three

and outer two speakers, respectively, of the MSL-4

array. These two outputs apply appropriate levels for

speakers directed at audience locations at different

distances from the main system. The diagram shows the

additional mid-hi output created by connecting the

CH 1 Loop to the CH 3 input. Using a Y-connection at

the CH 1 input, as shown for the down-fills, accomplishes

the same signal routing.

The Lo Cut and Array EQ switches for the Mid-Hi and

CH 3 outputs should be in. The Lo Cut filter eliminates

the rise caused by the overlap between the MSL-4 and

DS-2P/650-P systems. The Array EQ filter minimizes

the low-mid rise caused by the MSL-4 array.

The DS-2 and Sub outputs drive the DS-2P and 650-P

systems with the DS-2 & Crossover switch in. Set the

MSL-4 and DS-2P to the same polarity. The polarity of

the 650-P depends on the displacement from the flown

system.

CH 5 controls the CQ down-fill system. Since the main

system is normally set to a higher volume than the

down-fill system to project farther into the venue, the

main system is audible in the down-fill’s coverage

area. To insure that the speakers combine properly in

the overlapping coverage area:

• Set the CQ to the opposite polarity to the MSL-4

and DS-2P to phase align the mid-hi frequencies and

minimize the MSL-4’s low frequency down-lobe.

• Use the CH 5 Lo Cut filter to eliminate the low

frequency rise caused by the overlap with the

650-P/DS-2P systems.

• Delay the down-fill to compensate for the

propagation delay between the down-fill and

main systems in the intersecting coverage area.

(This is highly recommended, but not required.)

We recommend using the Meyer SIM System II Sound

Analyzer and CP-10 Parametric Equalizer to optimize this

configuration.

650-P Subwoofers

CQ Down-fills

DS-2P Mid-Bass

MSL-4 Mid-Hi

Input Mid-Hi

Output

DS-2

Output

Loop

Sub

Output

Input Output

LD-1A

Delay

CP-10 EQ

CH 1

CH 3

Input Output

CH 5

Set the MSL-4 and DS-2P to the same polarity; reverse

the polarity for the CQ. The polarity for the 650-P depends

on the displacement from the flown system.

Verifying Polarity

Incorrect driver polarity impairs system performance

and may damage the drivers. All Meyer Sound

loudspeakers are shipped with the drivers in correct

alignment. However, if the driver or circuit wiring has

been removed or disassembled in any loudspeaker in

a system for any reason, check the polarity between

adjacent loudspeakers and between drivers in the

same cabinet.

Polarity Between Adjacent Loudspeakers

Use the following test procedure to verify the polarity

between adjacent loudspeakers of the same type:

1. Position two loudspeakers adjacent to each other.

2. Place a measurement microphone six ft from the

speakers on the axis between them.

3. Connect a signal source to one speaker and note

the frequency response and overall level.

4. Apply the same signal to the second speaker with

the first speaker still connected.

Correct polarity causes

acoustic addition

Opposite polarity causes

acoustic cancellation

Top view of adjacent speakers with

measurement microphone

The polarity is correct if the frequency response

remains constant with a significant increase in

amplitude. Broadband cancellation (decreased overall

level) indicates polarity reversal.

Driver Polarity in the Same Loudspeaker

Use the following test procedure to verify polarity

between drivers in the same loudspeaker:

1. Place a monitoring microphone three ft from the

front of the loudspeaker at the midway point

between the low and high frequency drivers.

2. Connect a signal source to the loudspeaker and

note the frequency response.

Since polarity reversal causes excessive driver

excursion at high source levels, use moderate levels

when conducting this test.

Drivers with correct

polarity cause acoustic

addition

Drivers with reversed

polarity cause acoustic

cancellation

The polarity is correct if the frequency response is smooth

through the crossover region (±4 dB 600 Hz – 1 kHz).

Severe cancellation in the crossover region indicates

polarity reversal.

Coverage Angles and

Polar Plots

Coverage Angles

The coverage angles for the CQ Series over a wide

frequency range are summarized in the following table:

selgnAegarevoCseireSQC

latnoziroh

lacitrev

)stniopBd6–(1-QC 08 ° 04 °

)stniopBd01–(1-QC 001 ° 05 °

)stniopBd6–(2-QC 05 ° 04 °

)stniopBd01–(2-QC 06 ° 05 °

1. CQ-1: 500 Hz–16 kHz; CQ-2: 800 Hz–12 kHz

2. CQ-1 and CQ-2: 1.5–12 kHz

The –6 dB points denote the angle at which the measured

SPL has decreased to half its on-axis value. The –10 dB

points represent the angle at which the perceived SPL

has decreased to half its on-axis value.

Polar Plots

The data for the CQ Series polar patterns was measured

in Meyer Sound’s anechoic chamber (photo at right)

with the SIM System II Sound Analyzer in dB SPL at a

distance of 14 ft, using angular and frequency resolutions

of 1° and

⁄24 octave, respectively. The polar plots on

the following pages have been smoothed to angular

and frequency resolutions of 2° and 1 octave, and

normalized to 0 dB on-axis. Each polar pattern shows

the response of a 1 octave band centered at the frequency

indicated on the plot; there are no gaps in the data

from 125 Hz to 16 kHz.

The polar patterns reveal that the CQ-1 has a wider

horizontal coverage pattern than the CQ-2 and that

their vertical coverage is virtually identical. The uniform

beam width that distinguishes the CQ Series is evident

in their polar patterns in the horn’s range (1–16 kHz);

note the lack of side or back lobes.

The table below lists the maximum on-axis peak dB SPL

per octave measured at 1 m for the CQ-1 and CQ-2.

LPSBdkaePmumixaM

ycneuqerF 1-QC 2-QC

zH521 721721

zH052 031031

zH005 031031

zHk1 231931

zHk2 631931

zHk4 631931

zHk8 231431

zHk61 221421

Meyer Sound’s anechoic chamber

CQ-1: 125 Hz

CQ-1: 250 Hz

CQ-1: 1 kHzCQ-1: 500 Hz

CQ-1: 4 kHzCQ-1: 2 kHz

CQ-1: 8 kHz CQ-1: 16 kHz

vertical

CQ-1 Polar Plots

Inner plot is vertical unless

otherwise indicated.

CQ-2: 4 kHzCQ-2: 2 kHz

CQ-2: 125 Hz

CQ-2: 1 kHzCQ-2: 500 Hz

CQ-2: 250 Hz

CQ-2: 8 kHz CQ-2: 16 kHz

vertical

CQ-2 Polar Plots

Inner plot is vertical unless

otherwise indicated.

Array Design

Creating an effective array with the CQ requires a

precise understanding of how to combine the coverage

area and SPL of the individual speaker with those of

adjacent speakers. Array design is a trade-off between

increasing on-axis power and creating smooth transitions

between the coverage areas of adjacent speakers.

As the splay angle (the angle between adjacent cabinet

faces) decreases below the coverage angle of the

individual speaker, the on-axis power increases, but

the coverage overlap between adjacent speakers causes

comb filtering and other frequency response variations.

As the splay angle increases toward the coverage

angle, the on-axis power decreases, but the variations

in frequency response diminish. As the splay angle

increases beyond the coverage angle, noticeable gaps

begin to form in the array’s coverage area.

NOTE: The trapezoidal shape of the CQ does not

represent the horizontal coverage area of the speaker

or the intended splay angle for horizontal arrays. The

angle of the CQ enclosure is narrower than the

minimum recommended splay angle.

A series of outdoor tests was conducted at Meyer Sound

to determine the coverage angle and on-axis SPL for

arrays with one and two horizontal rows of up to four

elements each, at numerous splay angles. The measurements

were conducted at a distance of 8 m with half-space

loading; on-axis SPL values were interpolated from

8 m to 1 m. The coverage angle for the array is the result

of averaging the –6 dB points from 125 Hz to 8 kHz.

The horizontal splay angles in the tables below represent

the optimal configurations for narrow and wide coverage

areas; note the different angles for the CQ-1 and CQ-2.

The vertical angles represent the optimal narrow (15°),

middle (30°), and wide (40°) orientations for both the

CQ-1 and CQ-2. The 2@0° LT denotes the long throw

configuration: the two horns are coupled directly

together (top speaker upside down/bottom speaker

upright) to form a single narrow horn.

The following tables show the SPL and coverage areas

that result from grouping the CQ-1 and CQ-2 in arrays

of up to four units horizontally and two rows vertically.

All splay angles refer to the angle between cabinet

centers. If this information does not address your

application requirements, contact Meyer Sound to

obtain additional information on array design.

CQ-1 Array Coverage and Maximum SPL Chart

CQ-2 Array Coverage and Maximum SPL Chart

Number of Horizontal

CQ units @ Angle

1 2 @ 30° 2 @ 40° 3 @ 30° 3 @ 40° 4 @ 30° 4 @ 40°

Coverage Max Peak Coverage Max Peak Coverage Max Peak Coverage Max Peak Coverage Max Peak Coverage Max Peak Coverage Max Peak

H V dB SPL H V dB SPL H V dB SPL H V dB SPL H V dB SPL H V dB SPL H V dB SPL

Number of Vertical

Rows of CQ @ Angle

1 50° 40° 139 70° 40° 143 90° 40° 142 100° 40° 144 130° 40° 144 130° 40° 145 170° 40° 144

2 @ 0° (LT) 50° 20° 145 70° 20° 149 90° 20° 148 100° 20° 150 130° 20° 150 130° 20° 151 170° 20° 150

2 @ 15° 50° 45° 143 70° 45° 147 90° 45° 146 100° 45° 148 130° 45° 148 130° 45° 149 170° 45° 148

2 @ 30° 50° 60° 142 70° 60° 146 90° 60° 145 100° 60° 147 130° 60° 147 130° 60° 148 170° 60° 147

2 @ 40° 50° 80° 141 70° 80° 145 90° 80° 144 100° 80° 146 130° 80° 146 130° 80° 147 170° 80° 146

Number of Horizontal

CQ units @ Angle

1 2 @ 50° 2 @ 70° 3 @ 50° 3 @ 70° 4 @ 50° 4 @ 70°

Coverage Max Peak Coverage Max Peak Coverage Max Peak Coverage Max Peak Coverage Max Peak Coverage Max Peak Coverage Max Peak

H V dB SPL H V dB SPL H V dB SPL H V dB SPL H V dB SPL H V dB SPL H V dB SPL

Number of Vertical

Rows of CQ @ Angle

1 80° 40° 136 100° 40° 140 150° 40° 139 170° 40° 140 220° 40° 138 220° 40° 141 300° 40° 139

2 @ 0° (LT) 80° 20° 142 100° 20° 146 150° 20° 145 170° 20° 146 220° 20° 144 220° 20° 147 300° 20° 145

2 @ 15° 80° 45° 140 100° 45° 144 150° 45° 143 170° 45° 144 220° 45° 142 220° 45° 145 300° 45° 143

2 @ 30° 80° 60° 139 100° 60° 143 150° 60° 142 170° 60° 143 220° 60° 141 220° 60° 144 300° 60° 142

2 @ 40° 80° 80° 138 100° 80° 142 150° 80° 141 170° 80° 142 220° 80° 140 220° 80° 143 300° 80° 141

• To reduce the risk of electric shock, disconnect the loud-

speaker from the AC mains before installing audio cable.

Reconnect the power cord only after making all signal

connections.

• Connect the loudspeaker to a two-pole, three wire ground-

ing mains receptacle. The receptacle must be connected to a

fuse or circuit breaker. Connection to any other type of

receptacle poses a shock hazard and may violate local

electrical codes.

• Do not install the loudspeaker in wet or humid locations

without using weather protection equipment from Meyer

Sound.

• Do not allow water or any foreign object to get inside the

loudspeaker. Do not put objects containing liquid on, or

near, the unit.

• To reduce the risk of overheating the loudspeaker, avoid

exposing it to direct sunlight. Do not install the unit near

heat emitting appliances, such as a room heater or stove.

• This loudspeaker contains potentially hazardous voltages. Do

not attempt to disassemble the unit. The unit contains no

user serviceable parts. Repairs should be performed only by

factory trained service personnel.

English Français

Deutsch Español

Safety Summary

• Um die Gefahr eines elektrischen Schlages auf ein

Minimum zu reduzieren, den Lautsprecher vom

Stromnetz trennen, bevor ggf. ein Audio-

Schnittstellensignalkabel angeschlossen wird. Das

Netzkabel erst nach Herstellung aller

Signalverbindungen wieder einstecken.

• Der Lautsprecher an eine geerdete zweipolige

Dreiphasen-Netzsteckdose anschließen. Die Steckdose

muß mit einem geeigneten Abzweigschutz (Sicherung

oder Leistungsschalter) verbunden sein. Der Anschluß

der unterbrechungsfreien Stromversorgung an einen

anderen Steckdosentyp kann zu Stromschlägen führen

und gegen die örtlichen Vorschriften verstoßen.

• Der Lautsprecher nicht an einem Ort aufstellen, an dem

sie mit Wasser oder übermäßig hoher Luftfeuchtigkeit in

Berührung kommen könnte.

• Darauf achten, daß weder Wasser noch Fremdkörper in

das Innere den Lautsprecher eindringen. Keine Objekte,

die Flüssigkeit enthalten, auf oder neben die

unterbrechungsfreie Stromversorgung stellen.

• Um ein Überhitzen dem Lautsprecher zu verhindern,

das Gerät vor direkter Sonneneinstrahlung fernhalten

und nicht in der Nähe von wärmeabstrahlenden

Haushaltsgeräten (z.B. Heizgerät oder Herd) aufstellen.

• Im Inneren diesem Lautsprecher herrschen potentiell

gefährliche Spannungen. Nicht versuchen, das Gerät zu

öffnen. Es enthält keine vom Benutzer reparierbaren

Teile. Reparaturen dürfen nur von ausgebildetem

Kundenienstpersonal durchgeführt werden.

• Para reducir el riesgo de descarga eléctrica, desconecte

de la red el altoparlante antes de instalar el cable de

señalización de interfaz de la segnale. Vuelva a conectar

el conductor flexible de alimentación solamente una vez

efectuadas todas las interconexiones de señalizatción.

• Conecte el altoparlante a un tomacorriente bipolar y

trifilar con neutro de puesta a tierra. El tomacorriente

debe estar conectado a la protección de derivación

apropiada (ya sea un fusible o un disyuntor). La

conexión a cualquier otro tipo de tomacorriente puede

constituir peligro de descarga eléctrica y violar los

códigos eléctricos locales.

• No instale el altoparlante en lugares donde haya agua o

humedad excesiva.

• No deje que en el altoparlante entre agua ni ningún

objeto extraño. No ponga objetos con líquidos encima de

la unidad ni cerca de ella.

• Para reducir el riesgo de sobrecalentamiento, no

exponga la unidad a los rayos directos del sol ni la

instale cerca de artefactos que emiten calor, como estufas

o cocinas.

• Este altoparlante contiene niveles de voltaje peligrosos

en potencia. No intente desarmar la unidad, pues no

contiene piezas que puedan ser repardas por el usuario.

Las reparaciones deben efectuarse únicamente por parte

del personal de mantenimiento capacitado en la fábrica.

• Pour réduire le risque d’électrocution, débranchez la

prise principale de l’haut-parleur, avant d’installer le

câble d’interface allant à l’audio. Ne rebranchez le bloc

d’alimentation qu’après avoir effectué toutes les

connections.

• Branchez l’haut-parleur dans une prise de courant à 3

dérivations (deux pôles et la terre). Cette prise doit être

munie d’une protection adéquate (fusible ou coupe-

circuit). Le branchement dans tout autre genre de prise

pourrait entraîner un risque d’électrocution et peut

constituer une infraction à la réglementation locale

concernant les installations électriques.

• Ne pas installer l’haut-parleur dans un endroit où il y a

de l’eau ou une humidité excessive.

• Ne pas laisser de l’eau ou tout objet pénétrer dans l’haut-

parleur. Ne pas placer de r´cipients contenant un liquide

sur cet appareil, ni à proximité de celui-ci.

• Pour éviter une surchauffe de l’haut-parleur, conservez-

la à l’abri du soleil. Ne pas installer à proximité

d’appareils dégageant de la chaleur tels que radiateurs

ou appareils de chauffage.

• Ce haut-parleur contient des circuits haute tension

présentant un danger. Ne jamais essayer de le démonter.

Il n’y a aucun composant qui puisse être réparé par

l’utilisateur. Toutes les réparations doivent être

effectuées par du personnel qualifié et agréé par le

constructeur.

Complementary power MOSFET output stages class AB/H

1240 Watts (620 Watts/channel)

< .02 %

Acoustical

Part # 05.041.010.01 Rev A

±4 dB 40 Hz – 18 kHz

±90° 50 Hz – 16 kHz

CQ-1: 136 dB ; CQ-2: 139 dB

> 110 dB

Specifications

Frequency Response

Phase Response

Maximum Peak SPL

Dynamic Range

Coverage

CQ-1

–6 dB points

–10 dB points

–6 dB points

–10 dB points

CQ-2

CQ-1

CQ-2

Acoustical Crossover Point

Transducers

Low Frequency

High Frequency

Audio Input

Type

Connector

Nominal Input Level

Amplifiers

Type

Burst Capability

THD, IM, TIM

AC Power

Connector

Automatic voltage selection

Max Continuous RMS Current (> 10 s)

Max Burst RMS Current (< 1 s)

Max Peak Current During Burst

Soft Current Turn-on

Physical

Dimensions

Weight

Enclosure/Finish

Protective Grill

Rigging

10 kΩ impedance, electronically balanced

XLR (A-3) male and female

+4 dBu (1.23 Vrms)

H: 50° (800 Hz – 12 kHz); V: 40° (1.5 kHz – 12 kHz)

H: 60° (800 Hz – 12 kHz); V: 50° (1.5 kHz – 12 kHz)

15” diameter MS-15 cone

4” diaphragm MS-2001CQ horn compression driver

250 V NEMA L6-20P / IEC 309 Twistlock male receptacle

85 – 134 V / 165 – 264 V; 50 Hz / 60 Hz

115 V: 8 A 230 V: 4 A 100 V: 10 A

115 V: 15 A 230 V: 8 A 100 V: 18 A

115 V: 22 Apk 230 V: 11 Apk 100 V: 25 Apk

Inrush current < 12A @115V

21” W x 30” H x 22

⁄2” D

130 lb (59 kg); shipping: 150 lb (68 kg)

All birch plywood/black textured

Perforated steel grill, charcoal-grey foam

Four aircraft pan fittings (two on top and bottom).

Working load for each fitting is 500 lb (

⁄5 the cabinet

breaking strength) with straight tensile pull.

H: 80° (500 Hz – 16 kHz); V: 40° (1.5 kHz – 12 kHz)

H:100° (500 Hz – 16 kHz); V: 50° (1.5 kHz – 12 kHz)

700 Hz

900 Hz

Notes

1. Subject to half-space loading; measured

with one-third octave frequency resolution

in fixed ISO bands.

2. Measured as the ratio between the peak

SPL and the A-weighted noise floor.

3. Nominal 8

Ω

resistive load, pink noise,

100 V peak.

4. The unit is rated at 88 – 125 VAC and

182 – 235 VAC, 50/60 Hz, to satisfy EC

standards for –10% to 6% AC line voltage.

Meyer Sound Portable Speaker CQ-2 Manuel utilisateur

Marque: Meyer Sound

Modèle: Portable Speaker CQ-2

Catégorie: Amplificateur d'instruments de musique

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Meyer Sound Portable Speaker CQ-2 User manual

Meyer Sound Portable Speaker CQ-2 Manuel utilisateur

Ce manuel convient également à

Meyer Sound Portable Speaker CQ-2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents