ProTemp PT-80V-LPC-A User's Manual & Operating Instructions

Model Numbers

PT-80V-LPC-A / PT-200V-LPC-A

668 Stony Hill Road #302 Yardley, PA 19067 USA • Toll Free (800)-641-6996

Fax: (215)-891-8461 • Web: www.protemp.us • Email: [email protected]

User’s Manual &

Operating Instructions

CONSUMER: READ AND SAVE THESE INSTRUCTIONS

247000261-14

GENERAL HAZARD WARNING:

FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTIONS PROVIDED WITH

THIS HEATER, CAN RESULT IN DEATH, SERIOUS BODILY INJURY AND PROPERTY LOSS

OR DAMAGE FROM HAZARDS OF FIRE, EXPLOSION, BURN. ASPHYXIATION, CARBON

MONOXIDE POISONING AND / OR ELECTRIC SHOCK.

ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE INSTRUCTIONS SHOULD USE

OR SERVICE THIS HEATER.

IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS

MANUAL, LABEL, ETC. CONTACT THE MANUFACTURER.

DANGER

FIRE, BURN, INHALATION, AND EXPLOSION HAZARD. KEEP SOLID

COMBUSTIBLES, SUCH AS BUILDING MATERIALS, PAPER OR

CARDBOARD, A SAFE DISTANCE AWAY FROM THE HEATER AS RECOMMENDED BY

THESE INSTRUCTIONS. NEVER USE THE HEATER IN SPACES WHICH DO OR MAY

CONTAIN VOLATILE OR AIRBORNE COMBUSTIBLES, OR PRODUCTS SUCH AS GASOLINE,

SOLVENTS, PAINT THINNERS, DUST PARTICLES OR UNKNOWN CHEMICALS.

WARNING

®

Factory ID: 522

NEVER LEAVE HEATER UNATTENDED WHILE BURNING,

CONNECTED TO A POWER SOURCE, OR WHILE

CONNECTED TO A FUEL SOURCE

®

Table Of Contents

Safety Information.............................................1-3

Specications and Features..

..............................

4

Assembly..............................................................5

Operation..........................................................6-8

Ventilation..........................................................

..9

Maintenance........................................................9

Troubleshooting Guide.......................................10

Exploded View

..............................................

...

.

.11

Parts List............................................................12

Warranty.............................................................13

Safety Information

NOT FOR HOME OR RECREATIONAL VEHICLE USE.

WARNING

This is an unvented portable heater. It uses air (oxygen) from the area in which

it is used. Adequate combustion and ventilation air must be provided. Refer to

VENTILATION on Page 9.

WARNING

Carbon Monoxide Hazard This heater produces carbon monoxide, which has no

odor. Burning the heater in an enclosed space can kill you. Never use the heater

in enclosed spaces such as a tent, a camper, any vehicle or recreational vehicle (RV), enclosed

shelter, or any other enclosed areas.

DANGER

Not for use in residential living areas or in non-adequately ventilated enclosed

spaces. Never bring or store a propane cylinder indoors.

DANGER

This heater is designed and approved for use as a construction heater in accordance with Standard

ANSI Z83.7-2011/CSA 2.14-2011. CHECK WITH YOUR LOCAL FIRE SAFETY AUTHORITY IF YOU

HAVE ANY QUESTIONS ABOUT APPLICATIONS. Other standards govern the use of fuel gasses

and heating products for specic uses. Your local authority can advise you about these.

If the information in this manual is not followed exactly, a fire or explosion may

result causing property damage, personal injury or loss of life.

DANGER

DO NOT OPERATE THIS HEATER UNTIL YOU HAVE READ AND THOROUGHLY

UNDERSTAND THESE SAFETY AND OPERATING INSTRUCTIONS.

Failure to comply with the precautions and instructions provided with this heater can result in

death, serious bodily injury, property loss or damage from the hazards of fire, explosions, burns,

asphyxiation or carbon monoxide poisoning. Only persons who can read and understand these

instructions should use or service this heater.

WARNING

CALIFORNIA RESIDENTS: This product contains chemicals, including lead,

known to the State of California to cause birth defects or other reproductive harm.

Wash hands after handling.

WARNING

EXTREMELY HOT DURING OPERATION! Do Not touch any metal components

while in operation. Keep gasoline and any other flammable liquids away from hater.

WARNING

1

NEVER LEAVE HEATER UNATTENDED WHILE BURNING,

CONNECTED TO A POWER SOURCE, OR WHILE

CONNECTED TO A FUEL SOURCE

®

Safety Information

The products described in this manual are

propane direct-red, forced air heaters. Propane

forced air heaters are primarily intended for

use for temporary heating of buildings under

construction, alteration or repair. Direct-red

means that all of the combustion products of the

heater enter the heated space. This appliance

is rated at 98% combustion efciency, but does

produce small amounts of carbon monoxide.

Carbon monoxide is toxic. Humans can tolerate

only small amounts of carbon monoxide and so

precautions should be taken to provide proper

ventilation. Failure to provide proper ventilation

in accordance with the instructions in this manual

can result in death.

People with breathing problems should consult a

physician before using this heater.

Early signs of carbon monoxide poisoning

resemble the u. Symptoms of improper

ventilation / carbon monoxide poisoning are:

Headache • Dizziness • Nausea

• Dry Mouth

Sore Throat

• Burning of Nose and Eyes

If you experience any of these symptoms:

GET FRESH AIR AT ONCE! Have your heater

serviced and check for proper ventilation. Some

people are more affected by carbon monoxide

than others. These include: pregnant women,

those with heart or lung problems, anemia or those

under the influence of alcohol or at high altitudes.

FOR OUTDOOR USE. INDOOR USE

PERMITTED ONLY FOR: The temporary

heating of adequately ventilated buildings or

structures under construction, alteration or

repair! Provide at least a three square foot

(2,800 sq cm) opening of outside air for

every 100,000 Btu / Hr heater rating. Refer to

“Ventilation” on page 8 for further instructions.

WHAT TO DO IF THE SMELL OF GAS IS PRESENT:

– DO NOT attempt to light the heater.

– Extinguish any open ame.

– Shut off gas to heater.

– If odor continues, contact your local gas

supplier or re department.

– DO NOT touch or use any electric switch or

any electric device that can cause a spark.

– Immediately call your gas supplier from a

neighbors phone. Follow the gas suppliers

instructions.

– If you can not reach your gas supplier, call

the re department.

– Service must be done by a qualied

service agency.

NEVER store or use gasoline or other ammable

vapors and liquids in the vicinity of this heater.

NEVER store

a propane (LP) cylinder not

connected to this heater in the vicinity of this heater.

NEVER

connect heater to an unregulated gas supply.

NEVER

obstruct the flow of combustion and

ventilation air.

NEVER use duct work in front or rear of heater.

NEVER modify this heater or operate a heater that

has been modified.

NEVER service, move or handle heater while still

hot or operating

Keep all combustible materials away from this heater.

Minimum Clearance From Combustibles

Sides Top

48 in. 96 in.

RISK OF INDOOR AIR

POLLUTION!

WARNING

CARBON MONOXIDE POISONING

MAY LEAD TO DEATH!

DANGER

RISK OF BURNS, FIRE AND

EXPLOSION!

WARNING

PROPANE IS AN

EXPLOSIVE GAS.

DANGER

CAUTION! HOT WHILE IN

OPERATION. DO NOT TOUCH.

KEEP CHILDREN, ANIMALS, CLOTHING AND

COMBUSTIBLES AWAY FROM HEATER.

WARNING

2

NEVER LEAVE HEATER UNATTENDED WHILE BURNING,

CONNECTED TO A POWER SOURCE, OR WHILE

CONNECTED TO A FUEL SOURCE

®

– ALWAYS install the heater so that it is not directly

exposed to water spray, rain, dripping water, or

wind.

– Use heater in accordance with all local codes.

In the absence of local codes, refer to The

National Fuel Code, ANSI Z223.1.

– This heater is shipped from the factory

for use with propane (LP) gas only. Do not

convert to any other gas. Installation must

conform to local codes, or in their absence,

with the standard for the Storage and

Handling of Liquefied Petroleum Gases ANSI/

NFPA 58 and the Natural Gas and Propane

Installation Code CSA B149.1.

– Gas supply connections should be checked

by using a 50/50 soap and water solution.

Never use a ame to check for gas leaks.

– Locate LP cylinder at least 6 feet (10 ft. in

Canada) from the heater, and do not direct

heater discharge towards the LP cylinder

unless it is at least 20 feet from the heater.

– Use only the regulator and hose assembly

provided with this heater. Inspect the

regulator/hose assembly prior to each use of

the heater. If there is excessive abrasion or

wear, or if the hose is cut, replace it with the

proper assembly shown in the parts list, prior

to using the heater.

Minimum and Maximum Inlet Pressure

80V-LPC-A 200V-LPC-A

Min. 5 PSI

Max. Bottle Pressure

Safety Information

The hose assembly shall be

pro tected from traffic, building

material and contact with hot surfaces both

during use and while in storage.

WARNING

1. Remove all packing items applied to heater for

shipment. Keep plastic cover caps attached to

inlet connector and hose / regulator assembly

for storage.

2. Remove all items from carton

3. Check all items for shipping damage. If the

heater is damaged, promptly inform dealer

where you purchased the heater.

The Propane (LP) gas

pressure regulator and hose

assembly supplied with the heater must be

used without alteration.

CAUTION

Unpacking

X

RISK OF FIRE! ALWAYS LOCATE HEATER ON A STABLE AND LEVEL SURFACE!

WARNING

Figure 1

For use with propane (LP)

gas only.

WARNING

3

NEVER LEAVE HEATER UNATTENDED WHILE BURNING,

CONNECTED TO A POWER SOURCE, OR WHILE

CONNECTED TO A FUEL SOURCE

®

Features

PT-80V-LPC-A

Base

Gas Valve Knob

Upper Shell

Figure 2

Specications

Model # PT-80V-LPC-A PT-200V-LPC-A

BTU 60,000 / 70,000 / 80,000 70,000 ‒ 200,000

Fuel Consumption (Lbs./hr) 2.8 / 3.2 / 3.7 3.2 ‒ 9.3

Heat Settings 3 Variable

Maximum Operating Hours 36 31

Required Cylinder Lbs. 100 100

Fuel Type Propane Propane

Heating Area (Ft.

2

) 1,800 5,000

Specications subject to change without notice.

Inlet Connector

Lower Shell

PT-200V-LPC-A

Figure 3

4

NEVER LEAVE HEATER UNATTENDED WHILE BURNING,

CONNECTED TO A POWER SOURCE, OR WHILE

CONNECTED TO A FUEL SOURCE

®

Assembly Instructions

What’s In The Box

Attaching The Upper Housing

1. Slide Upper Housing straight up and off of

lower housing and remove all packed items

from inside the heater. (See Figure 4)

2. Remove all packaging protecting the heater

during shipping. Retain caps for covering the

inlet connector and regulator hose fro storage.

3. Inspect heater closely for any damage that

may have occurred during shipping. If there is

any damage, return the heater to the place of

purchase.

4. Attach three (3) screws to the bottom row of

holes in the lower housing. (See Figure 5)

5. Slide upper housing over lower housing,

lining up the four remaining screw holes.

Insert three (3) screws and tighten securely.

(See Figure 5)

NOTE: Save carton and packaging material

for later storage.

11 mm Screws (6) Regulator (1) Upper Housing (1)

Missing Parts? Please Call 800-641-6996 For Assistance

Figure 4 Figure 5

5

NEVER LEAVE HEATER UNATTENDED WHILE BURNING,

CONNECTED TO A POWER SOURCE, OR WHILE

CONNECTED TO A FUEL SOURCE

®

Operation

Propane Supply / Information:

Propane (LP)

This heater is not supplied with a propane cylinder.

Use only an approved propane cylinder.

LP Characteristics

– Flammable, explosive under pressure, heavier

than air and pools in low areas.

– In its natural state, propane has no odor, but

for your safety an odor that smells like rotten

cabbage has been added.

– Contact of propane (LP) gas with the skin can

cause freeze burns.

– Heater is manufactured for use with propane

gas only. DO NOT attempt to convert to any

other gas. Such modications are dangerous

and will void the warranty.

– When heater is not in use, LP Cylinder must be

turned OFF.

– Be sure that the LP Cylinder is located on a

level and stable surface.

– DO NOT use this heater in a basement or

below ground level. Propane is heavier than

air and will always seek the lowest level. If you

suspect a leak, shut off the valve at the LP

Cylinder immediately.

The Propane (LP) cylinder must also be

equipped with the following

– A collar to protect the gas valve.

– A shut-off valve terminating a LP cylinder valve

outlet as specied in the American National

Standard for Compressed Gas Cylinder Valve

Outlets and Inlets Connections.

– A safety relief valve having direct

communications with the vapor space of the LP

cylinder.

– The heater must operate on vapor withdrawal

from the operating cylinder.

The amount of Propane (LP) used with this

heater varies. Both factors are

– The amount of gas in the cylinder of LP.

– The temperature of the LP tank and its

surroundings.

– Always keep LP cylinder fastened and upright.

– Avoid tipping the LP cylinder on its side when

connected to a regulator, since this may

cause damage to diaphragm in the regulator.

– Handle valves with care.

– Never connect an unregulated LP cylinder to

a construction heater.

– DO NOT subject LP cylinder to excessive heat.

– Tightly close the gas shutoff valve on the LP

cylinder after each use.

– All ttings must be protected when

disconnected from the LP cylinder.

– Never store an LP cylinder inside a building or

in the vicinity of an gas burning appliances.

Average Temp

(ºF)

80V-LPC-A

100 lb. cylinder

200V-LPC-A

100 lb. cylinder

32º 1 2

20º 1 2

10º 2 3

0º 2 3

-10º 2 3

-20º 2 3

The table above shows the minimum number of 100 lb. LP

cylinders required in cold weather. Your local LP dealer will

help you select the proper LP supply System

Propane is safe to use when

properly handled. Careless

handling of the LP cylinder could result in a

fire and or an explosion.

CAUTION

The disconnected tank must

never be stored in a building,

garage or any other enclosed area.

CAUTION

6

NEVER LEAVE HEATER UNATTENDED WHILE BURNING,

CONNECTED TO A POWER SOURCE, OR WHILE

CONNECTED TO A FUEL SOURCE

®

Operation

Pre-Lighting Instructions:

Connecting the LP Cylinder

ALL NEW LP CYLINDERS MUST BE PURGED

BEFORE THE FIRST FILLING.

– Turn heater gas valve knob and LP cylinder

valve to OFF position.

– LP cylinder valve equipped with old style

tting has LEFT HANDED THREADS. Turn

tting CLOCKWISE to loosen. Protect this

tting when disconnected from LP cylinder.

– Have your LP cylinder lled by your local

propane gas supplier.

– Some LP cylinders have a bleed-OFF valve.

This valve should be inspected for leaks after

each lling of the LP cylinder. Turn the valve

clockwise to close.

– Fasten full propane tank and connect

proper tting to LP cylinder valve by turning

COUNTER-CLOCKWISE.

– With heater gas valve knob still in OFF

position turn ON the LP cylinder valve and

check for leaks with soap solution.

Checking For Leaks

– To check for leaks, make up a 50/50 solution

of dish soap and water. Apply this solution

to all gas connections. If bubbles appear,

there is a leak. If a leak is found, turn off

the gas supply, and re-connect the leaking

connection. If the leak persists after several

tries, contact Pinnacle Customer Service at

(800)-641-6996.

– The installation of this heater must meet all

local codes and/or gas utility requirements. In

the absence of local codes, the National Fuel

Code ANSI Z223.1 should be followed.

– The minimum clearances to any combustible

construction materials must be maintained at

all times (See Page 2).

– Inspect the heater before each use, and at

least annually by a qualied service person.

Purging and filling of the

LP cylinders must be

performed by personnel who have been

thoroughly trained in accepted LP gas

industry procedures. Failure to follow these

instructions may result in explosion, fire,

severe personal injury or death.

WARNING

Supply Valve

Regulator

Hose

Propane Tank

Figure 6 Figure 7

Hose

Inlet

Connector

7

NEVER LEAVE HEATER UNATTENDED WHILE BURNING,

CONNECTED TO A POWER SOURCE, OR WHILE

CONNECTED TO A FUEL SOURCE

®

Lighting Instructions:

PT-80V-LPC-A

1. STOP! Read all of the safety information

provided with this heater.

2. Turn valve on propane cylinder

COUNTERCLOCKWISE until fully open.

3. Press in control knob and turn

COUNTERCLOCKWISE to LOW/IGN position.

4. If burner does not ignite, turn control knob to

OFF position and repeat the ignition procedure.

5. Keep control knob pressed in for approximately

30 seconds before releasing.

6. If the ame goes out, wait 5 minutes and

repeat the ignition and lighting steps.

7. After heater ignites, turn the control knob to

desired heat setting.

Relighting Instructions

1. Rotate valve on cylinder CLOCKWISE to close

it and wait 5 minutes.

2. Relight following the Lighting Instructions,

steps 1-7.

Shut Down Instructions

1. Turn control knob to the OFF position.

2. Rotate valve cylinder CLOCKWISE to close it.

PT-200V-LPC-A

1. STOP! Read all of the safety information

provided with this heater.

2. Turn valve on propane cylinder

COUNTERCLOCKWISE until fully open.

3. Set control valve to LIGHT/LOW position,

then wait 15 seconds before step 4.

4. Depress the red button on the safety valve,

admitting gas to the burner. While pressing

the safety valve, push and release the ignition

button until the burner lights.

5. When the burner lights, continue to keep the

red safety valve depressed for 30 seconds

then release.

6. If burner goes out, wait 5 minutes and repeat

lighting procedure.

7. When burner lights, you can now adjust the

heat setting to HIGH by sliding the control

valve up to the HIGH setting.

NOTE: When adjusting heat setting, the control

valve only needs to slightly slide up to achieve

HIGH setting.

Relighting Instructions

1. Rotate valve on cylinder CLOCKWISE to close

it and wait 5 minutes.

2. Relight following the Lighting Instructions,

steps 1-7.

Shut Down Instructions

1. Rotate valve cylinder CLOCKWISE to close it.

Operation

EXTREMELY HOT during operation. Do Not touch any metal components while in

operation. Keep gasoline and any other flammable liquids away from the heater.

WARNING

8

NEVER LEAVE HEATER UNATTENDED WHILE BURNING,

CONNECTED TO A POWER SOURCE, OR WHILE

CONNECTED TO A FUEL SOURCE

®

Ventilation

– Risk of indoor air pollution and Carbon

Monoxide Poisoning. Use heater only in

well ventilated areas.

– Refer to Safety Information on pages 1-2

for information about Carbon Monoxide

Poisoning.

– ALWAYS provide a fresh air opening in the

heated space of at least three square feet

(2,800 sq. cm) for each 100,000 BTU / Hr.

of heater output. Provide a larger opening if

more heaters are being used.

Minimum Ventilation Opening Needed

80V-LPC-A 200V-LPC-A

2.4 ft.

2

6.0 ft.

2

2220 cm

2

5570 cm

2

CARBON MONOXIDE POISONING MAY LEAD TO DEATH!

DANGER

Not for use in residential

living areas or in

non-adequately ventilated enclosed spaces.

DANGER

Storage / Maintenance

Always disconnect the heater from the LP

cylinder before putting the heater into storage. If

for any reason the heater is to be stored indoors,

the tank MUST be disconnected from the LP

cylinder, and the cylinder stored outdoors in a

well-ventilated area, out of the reach of children,

and in accordance with the Standard for Storage

and Handling of Petroleum Gases, ANSI/NFPA

58 - latest edition and Natural Gas and Propane

Installation Code, CSA B149.1. The plastic valve

plug or valve cover supplied with the cylinder

must be re-installed on the valve to protect the

fitting from damage.

NOTE: Installation and repair of this heater

should be done by a qualified service person.

ALWAYS be sure to follow proper maintenance

procedures. This should include cleaning the

inside of the heater once a month and checking

the spark gap at least once a heating season.

Re-gap the terminals to 0.195” (4.9 mm).

Never store an LP cylinder

inside of a building or near

any other gas or oil burning appliances.

DANGER

9

NEVER LEAVE HEATER UNATTENDED WHILE BURNING,

CONNECTED TO A POWER SOURCE, OR WHILE

CONNECTED TO A FUEL SOURCE

®

Problem Possible Cause Solution

Burner fails to ignite

1. Valve on supply cylinder

closed.

2. Cylinder excess flow check

valve closed.

3. Burner nozzle blockage.

4. Ignition system not sparking.

1. Open cylinder valve.

2. Close cylinder valve,wait

one minute, and re-open

slowly.

3. Replace Burner Nozzle.

4. Inspect igniter wires for

damage, be sure spark gap

is .195”.

Burner lights, but the flame goes

out when Control Knob is turned

to desired setting

1. Not enough time for

thermocouple to warm up.

2. Gas pressure too low.

3. Thermocouple needs

replacing, or loose.

4. Control valve damaged.

1. Keep Control Valve

depressed for at least 30

seconds.

2. Check cylinders for

adequate gas.

3. Replace or tighten

thermocouple connection.

4. Replace Control Valve.

Burner flame is too low

1. Cylinder valve not fully

open.

2. Clogged burner orifice.

3. Gas pressure too low.

4. Fuel supply too low.

1. Be sure cylinder valve is

fully opened.

2. Replace burner.

3. Be sure regulator is

operating properly.

4. Replace low fuel supply with

new, full cylinder.

Troubleshooting Guide

Locating Your Serial Number:

Your serial number can be found on the heater’s rating label. It will begin with the letters PGCV

followed by 8 digits. For Example: PGCV12345678. Have your Serial Number ready before calling

customer service at 800-641-6996.

10

NEVER LEAVE HEATER UNATTENDED WHILE BURNING,

CONNECTED TO A POWER SOURCE, OR WHILE

CONNECTED TO A FUEL SOURCE

®

1

2

3

4

5

6

7

8

9

10

11

12

13

14

13

14

15

16

17

18

19

20

18

19

20

21

22

Exploded View

11

Figure 8

PT-80V-LPC-A

PT-200V-LPC-A

NEVER LEAVE HEATER UNATTENDED WHILE BURNING,

CONNECTED TO A POWER SOURCE, OR WHILE

CONNECTED TO A FUEL SOURCE

®

Parts List

12

Item # Description PT-80V-LPC-A PT-200V-LPC-A

1 Upper Shell 24-525-0013 25-525-0014

2 Lower Shell 24-525-0015 24-525-0016

3 Regulator 24-041-0001 24-041-0004

4 Inlet Connector 24-507-0013 24-507-0014

5 Safety Valve ― 24-013-0003

6 Control Valve ― 24-015-0003

7 Piezo Lighter ― 24-122-0003

8 Valve Assembly 24-011-0020 ―

9 Wind Screen 24-526-0001 24-526-0001

10 Base 24-501-0010 24-501-0011

11 Thermocouple 24-091-0002 24-091-0003

12 Thermocouple Bracket 24-504-0007 24-504-0007

13 Spark Plug 24-141-0001 24-141-0001

14 Spark Plug Bracket 24-504-0008 24-504-0008

15 Connector Outlet ― 24-507-0015

16 Ignitor Wire ― 24-601-0005

17 Outlet Tubing Assembly 24-605-0006 24-605-0007

18 Nozzle Nut 24-518-0005 24-518-0005

19 Nozzle Holder 24-515-0001 24-515-0001

20 Nozzle 24-081-0007 24-081-0008

21 Ball Valve ― 22-504-0014

22 Gas Valve Knob 24-100-0001 ―

NEVER LEAVE HEATER UNATTENDED WHILE BURNING,

CONNECTED TO A POWER SOURCE, OR WHILE

CONNECTED TO A FUEL SOURCE

®

LIMITED WARRANTY

Pinnacle Products International, Inc. warrants this heater

to the original retail purchaser only, to be free from defects

in material and workmanship for a period of one (1) year

from the date of initial purchase. This product must be

properly installed, maintained and operated in accordance

with the instructions provided.

Pinnacle Products International, Inc. requires reasonable

proof of your date of purchase from an authorized retailer

or distributor. Therefore, you should keep your sales slip,

invoice or cancelled check from the original purchase.

This Limited Warranty shall be limited to the repair or

replacement of parts, which prove defective under normal

use and service within the warranty period, and which

Pinnacle Products International , Inc. shall determine at

its reasonable discretion.

This warranty does not apply to products purchased for

rental use.

This Limited Warranty does not cover any failures or

operating difculties due to normal wear and tear, accident,

abuse, misuse, alteration, misapplication, improper

installation or improper maintenance and service by you

or any third part. Failure to perform normal and routine

maintenance on the heater, shipping damage, damage

related to insects, birds or animals of any kind, and damage

due to weather conditions are also not covered.

In addition, the Limited Warranty does not cover damage

to the nish, such as scratches, dents, discoloration, rust or

other weather damage, after purchase.

All transportation costs for the return of damaged product

or parts will be the responsibility of the purchaser.

Upon receipt of damaged item, Pinnacle Products

International, Inc. will examine the item and determine if

defective. Pinnacle Products International, Inc. will repair

or replace and return the item, freight pre-paid.

If Pinnacle Products International, Inc. nds the item to

be in normal operating condition, or not defective the item

will be returned freight collect. This Limited Warranty is in

lieu of all other express warranties. Pinnacle Products

International, Inc. disclaims al warranties for products that

are purchased from sellers other than authorized dealers or

distributors.

AFTER THE PERIOD OF THE ONE (1) YEAR EXPRESS

WARRANTY EXPIRES, Pinnacle Products International,

Inc. DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,

INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

APPLICATION. FURTHER, Pinnacle Products International,

Inc. SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER

OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE

INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Pinnacle

Products International, Inc. assumes no responsibility for

any defects caused by third parties. This Limited Warranty

gives the purchaser specic legal rights; a purchaser may

have other rights depending upon where he or she lives.

Some states do not allow the exclusion or limitation of

special, incidental or consequential damages, or limitations

on how long a warranty lasts, so the above exclusion and

limitations may not apply to you.

Pinnacle Products International, Inc. does not authorize

any person or company to assume for it any other

obligation or liability in connection with the sale, installation,

use, removal, return or replacement of its equipment, and

no such representations are binding on Pinnacle Products

International, Inc.

Always be sure to specify the model number and serial

number when making any claim with Pinnacle Products

International, Inc. For your convenience, use the space

provided below to list this information.

Register Your Product Online at: http://www.protemp.us/Product_Registration.php

Model #:________________________________

Serial #:________________________________

Date of Purchase: ________________________

Locating Your Serial Number:

Your serial number can be found on the heater’s rating label. It will begin with the letters PGCV followed by 8

digits. For Example: PGCV12345678. Have your Serial Number ready before calling customer service

at 800-641-6996.

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

Serial Number Label

13

NEVER LEAVE HEATER UNATTENDED WHILE BURNING,

CONNECTED TO A POWER SOURCE, OR WHILE

CONNECTED TO A FUEL SOURCE

®

____________________________________________________________

14

668 Stony Hill Road #302 Yardley, PA 19067 USA • Toll Free (800)-641-6996

Fax: (215)-891-8461 • Web: www.pinnacleint.com • Email: [email protected]

668 Stony Hill Road #302 Yardley, PA 19067 USA Toll Free (800)-641-6996

Fax: (215)-891-8461 

247000261-14

Modelos No

PT-80V-LPC-A / PT-200V-LPC-A

®



SI NO CUMPLE CON LAS PRECAUCIONES Y LAS INSTRUCCIONES QUE SE LE PROPORCIONAN

CON ESTE CALENTADOR, PUEDE PROVOCAR LA MUERTE, LESIONES CORPORALES GRAVES,

Y PÉRDIDA DE LA PROPIEDAD O PELIGRO DE INCENDIO, EXPLOSIÓN O QUEMADURA, ASFIXIA,

ENVENENAMIENTO POR MONÓXIDO DE CARBONO, Y/O CHOQUE ELÉCTRICO.

ESTE CALENTADOR SOLAMENTE LO DEBEN USAR O DARLE MANTENIMIENTO LAS

PERSONAS QUE PUEDAN COMPRENDER Y SEGUIR LAS INSTRUCCIONES.

SI NECESITA AYUDA O INFORMACIÓN SOBRE EL CALENTADOR, TAL COMO UN MANUAL DE

INSTRUCCIONES, ETIQUETAS, ETCÉTERA, PÓNGASE EN CONTACTO CON EL FABRICANTE.

PELIGRO DE INCENDIO, QUEMADURAS, INHALACIÓN Y EXPLOSIÓN.

MANTENGA LOS COMBUSTIBLES SÓLIDOS COMO, POR EJEMPLO,

MATERIALES DE CONSTRUCCIÓN, PAPEL Y CARTÓN, A UNA DISTANCIA PRUDENCIAL

DEL CALENTADOR SEGÚN LO RECOMIENDAN LAS INSTRUCCIONES. NUNCA USE EL

CALENTADOR EN ESPACIOS QUE CONTENGAN O PUEDAN CONTENER COMBUSTIBLES

VOLÁTILES O EN SUSPENSIÓN EN EL AIRE NI PRODUCTOS COMO, POR EJEMPLO,

GASOLINA, DISOLVENTES, SOLVENTES DE PINTURA, PARTÍCULAS DE POLVO O QUÍMICOS

DESCONOCIDOS.

Manual del Usario e

Instructiones



Factory ID: 522



NUNCA DEJE DESATENDIDO EL CALENTADOR MIENTRAS

ÉSTE ESTÉ ENCENDIDO O MIENTRAS ESTÉ CONECTADO A

UNA FUENTE DE COMBUSTIBLE.

Manual del Usuario del Calentador de Convección

®



Información Sobre Seguridad...........................1-3

Características y Especicaciones......................4

Montaje..

..............................................................5

Operación..........................................................6-8

Ventilación

.........................................................

..9

Mantenimiento......................................................9

Guía de Solución de Problemas........................10

Dibujo de Despiece de Piezas...........................11

Lista de Recambios ..........................................12

Garantía.............................................................13



 No

toque los elementos metálicos mientras esté encendida la unidad. Mantenga el

calentador lejos de gasolina y otros líquidos inflamables.

1

.

Éste es un calentador portátil sin ventilación. La unidad utiliza el aire (oxígeno) del

espacio donde se usa. Será necesario suministrar suficiente aire para la combustión y

ventilación. Consultar VENTILACIÓN, página 9.

Este calentador produce

monóxido de carbono, que es un gas inodoro. Encender el calentador en un

espacio cerrado puede ocasionarle la muerte. Nunca use el calentador en espacios cerrados

como, por ejemplo, tiendas, remolques, cualquier tipo de vehículo (entre ellos, vehículos de uso

recreativo), recintos cerrados

No debe utilizarse en áreas residenciales ni en espacios cerrados con mala

ventilación. Nunca ingrese o almacene un cilindro de propano en espacios interiores.

Este calentador ha sido diseñado para uso en construcciones de acuerdo con la normas

ANSI Z83.7-2011/CSA 2.14-2011. CONSULTE CON LAS AUTORIDADES DE SEGURIDAD

DE INCENDIOS DE SU LOCALIDAD SI TIENE ALGUNA DUDA SOBRE EL USO DE ESTE

CALENTADOR. Otras normas rigen el uso de gases combustibles y productos de calefacción para

usos específicos. Sus autoridades locales pueden asesorarle sobre esas normas.

Si la información contenida en este manual no se sigue exactamente, un incendio

o una explosión puede causar daños materiales,lesiones personales o pérdida de

la vida.





El no cumplir con las precauciones e instrucciones provistas con este calentador puede resultar en

muerte, lesiones serias, pérdida de propiedad, daños por fuego, producción de hollín, explosiones,

quemaduras, asfixia o envenenamiento por monóxido de carbono. Solamente personas que

puedan leer y comprender estas instrucciones deben usar o realizar servicio a este calentador.

Este producto contiene sustancias químicas,

incluyendo plomo, conocido en el estado de California para causar defectos de

nacimiento u otros daños reproductivos. Lávarse las manos después de manipular.

NUNCA DEJE DESATENDIDO EL CALENTADOR MIENTRAS

ÉSTE ESTÉ ENCENDIDO O MIENTRAS ESTÉ CONECTADO A

UNA FUENTE DE COMBUSTIBLE.

Manual del Usuario del Calentador de Convección

®



2

Los productos descritos en este manual son

calentadores de aire forzado e impulsados

directamente a kerosén.Los calentadores de aire

forzado a kerosén están pensados principalmente para

calentamiento temporal de edicios en construcción,

alteración o reparación.Impulsados directamente

signican que todos los productos de combustión

del calentador ingresan en el espacio calentado.

Este dispositivo está clasicado para que tenga 98%

de eciencia de combustión pero produce pequeñas

cantidades de monóxido de carbono.

El monóxido de carbono es tóxico. Los humanos

pueden tolerar pequeñas cantidades de monóxido de

carbono, y por tanto, deben tomarse las medidas de

precaución necesarias para suministrar una ventilación

adecuada. No proporcionar la ventilación adecuada de

acuerdo con este manual puede ocasionar la muerte.

Las personas con problemas respiratorios deberían

consultar con un médico antes de usar el calentador.

Los primeros síntomas de envenenamiento a causa

del monóxido de carbono se parecen a los de la

gripe. Los síntomas de ventilación inadecuada o

envenenamiento por monóxido de carbono son:

Mareo  Náusea

 



Si tiene alguno de estos síntomas:

¡SALGA AL AIRE LIBRE DE INMEDIATO! Haga

revisar a su calentador para comprobar que la

ventilación es la adecuada. Algunas personas se ven

más afectadas que otras por el monóxido de carbono.

Por ejemplo: mujeres embarazadas, personas con

problemas pulmonares o cardíacos, anemia o bajo

influencia del alcohol o en grandes altitudes.





















:

– No trate de encender el calentador.

– .

– .

– 



su localidad.

– 





– 



.

– 

.

– 

.

NUNCA No guarde ni utilice gasolina u otros gases

y líquidos inflamables cerca de este o cualquier otro

artefacto.

NUNCA almacenar cilindros de propano (PL) que

no se encuentren conectado a este radiador en los

alrededores de éste.

NUNCA

conecte el calentador en una fuente de gas no

regulada.

NUNCA obstruir el ujo del aire de combustión y

ventilación (parte delantera y trasera del calentador).

NUNCA use el funcionamiento de ducto en la parte

frontal o posterior del calentador.

NUNCA modifique el calentador ni utilice un

calentador que haya sido modificado.

NUNCA repare ni le dé mantenimiento al calentador

mientras está caliente o funcionando.

Mantenga todos los materiales combustibles lejos de

este calentador

.



Lados Superior

48 in. 96 in.





























NUNCA DEJE DESATENDIDO EL CALENTADOR MIENTRAS

ÉSTE ESTÉ ENCENDIDO O MIENTRAS ESTÉ CONECTADO A

UNA FUENTE DE COMBUSTIBLE.

Manual del Usuario del Calentador de Convección

®

– SIEMPRE instale el calentador para que no esté

expuesto directamente a rocío de agua, lluvia,

goteras o viento.

– Use el calentador de acuerdo con todos los

códigos locales. En ausencia de códigos locales,

consulte el Código Nacional de Combustibles,

ANSI Z223.1.

– 

. No lo

convierta a ningún otro gas. La instalación deberá

conformar con los códigos locales, o a falta de

ellos, con la norma para el almacenamiento y

la manipulación de gases de petróleo licuado

ANSI/NFPA 58, y el gas natural y el Código de

Instalación de gas propano, CSA B149.1.

– Las conexiones de suministro de gas deben

revisarse usando una solución de 50/50 de agua

y jabón. Nunca use una llama para verificar la

presencia de fugas de gas.

– Sitúe el cilindro de propano al menos a 1.8 metros

del calentador (3.1 metros en Canadá), y no

oriente la descarga del calentador hacia el cilindro

de gas a menos que éste se encuentre a una

distancia de 6 metros del calentador.

– Utilice únicamente el conjunto de regulador y

manguera suministrado con este calentador.

Inspeccione el conjunto del regulador y manguera

antes de cada uso del calentador. Si está

demasiado desgastado, o si la manguera está

cortada, reemplace el conjunto con el conjunto

correcto mostrado en la lista de partes, antes de

usar el calentador

.

Presión de Gas

80V-LPC-A 200V-LPC-A

Min. 34.5 kPa (5 PSI)

Max. Presion de la botella















X





Figura 1





3

1. Retire todos los materiales de embalaje aplicados

al calentador para su envío. Mantenga montadas

las tapas de plástico en el conector de entrada y

en el conjunto del regulador y manguera cuando

almacene la unidad.

2. Retire todos los artículos de la caja de envío

3. Inspeccione los artículos para com probar que

no se hayan dañado durante el envío. Si el

calentador está dañado, infórmele prontamente

al concesionario de quien compró el calentador

sobre dicho daño.













La page est en cours de chargement...

ProTemp PT-80V-LPC-A User's Manual & Operating Instructions

Ce manuel convient également à

ProTemp PT-80V-LPC-A User's Manual & Operating Instructions

dans d''autres langues

Documents connexes

Autres documents