Kobalt VT6389 Manuel utilisateur

Catégorie
Compresseurs d'air
Taper
Manuel utilisateur
IN638401AV 5/13
PORTABLE
AIR
COMPRESSOR
ITEM #0268707
MODEL #VT6389
Français p. 29
Español p. 59
KOBALT
®
and the K Design
®
are registered
trademarks of LF, LLC. All Rights Reserved.
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-888-3KOBALT (1-888-356-2258), 8 a.m. - 8 p.m., EST,
Monday - Friday.
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
1
AB13473
kobalttools.com
Safety Guidelines .......................................................................................................................... 3
Safety Information ......................................................................................................................... 3
Package Contents ......................................................................................................................... 6
Hardware Contents........................................................................................................................ 6
Preparation .................................................................................................................................... 7
Assembly Instructions.................................................................................................................... 8
Operating Instructions ................................................................................................................... 13
Care and Maintenance .................................................................................................................. 15
Troubleshooting ............................................................................................................................. 16
Warranty ........................................................................................................................................ 20
Replacement Parts List ................................................................................................................. 22
2
TABLE OF CONTENTS
PRODUCT SPECIFICATIONS
COMPONENT SPECIFICATIONS
Model VT6389
HP 2
Number of Cylinders 2
Air Delivery @ 90 psi 5.5 CFM
Voltage 120 Volts / 15 Amps
Max Pressure 155 psi
COMPONENT SPECIFICATIONS
Oil Capacity 8.5 oz.
Tank Outlet Size 1/4 NPT
Depth 23 in.
Width 24 in.
Height 46 in.
Weight 178 lbs.
kobalttools.com
3
Please read and understand this entire manual before attempting to assemble, operate or install
the product. If you have any questions regarding the product, please call customer service at
1-888-3KOBALT (1-888-356-2258), 8:00 am - 8:00 pm, EST, Monday - Friday.
This manual contains information that is very important to know and understand. This information
is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help recognize this
information, observe the following symbols.
SAFETY GUIDELINES
CALIFORNIA PROPOSITION 65
CAUTION
Caution indicates a potentially hazardous
situation which, if not avoided, MAY result in
minor or moderate injury.
NOTICE
Notice indicates important information,
that if not followed, may cause damage to
equipment.
DANGER
Danger indicates an imminently hazardous
situation which, if not avoided, WILL result in
death or serious injury.
WARNING
Warning indicates a potentially hazardous
situation which, if not avoided, COULD result
in death or serious injury.
SAFETY INFORMATION
WARNING
Handle with Care. This product or its power
cord may contain chemicals known to the
State of California to cause cancer and birth
defects or other reproductive harm. Wash
hands after handling.
WARNING
Wear eye and mask protection.
You can create dust when you cut,
sand, drill or grind materials such
as wood, paint, metal, concrete,
cement, or other masonry. This
dust often contains chemicals
known to cause cancer, birth
defects, or other reproductive
harm. Wear protective gear.
GENERAL SAFETY
Since the air compressor and other components (material pump, spray guns, filters, lubricators,
hoses, etc.) used, make up a high pressure pumping system, the following safety precautions must be
observed at all times:
1. Read all manuals included with this product carefully. Be thoroughly familiar with the controls
and the proper use of the equipment.
2. Follow all local electrical and safety codes as well as in the United States, the National Electrical
Codes (NEC) and Occupational Safety and Health Act (OSHA).
3. Only persons well acquainted with these rules of safe operation should be allowed to use the
compressor.
4. Keep visitors away and NEVER allow children in the work area.
5. Wear safety glasses and use hearing protection when operating the unit.
kobalttools.com
GENERAL SAFETY (Continued)
6. Do not stand on or use the unit as a handhold.
7. Before each use, inspect compressed air system and electrical components for signs of damage,
deterioration, weakness or leakage. Repair or replace defective items before using.
8. Check all fasteners at frequent intervals for proper tightness.
9. Do not wear loose clothing or jewelry that will get caught in the moving parts of the unit.
10. Keep fingers away from a running compressor; fast moving and hot parts will cause injury and/or
burns.
11. If the equipment should start to vibrate abnormally, STOP the engine/motor and check
immediately for the cause. Vibration is generally a warning of trouble.
12. To reduce fire hazard, keep engine/motor exterior free of oil, solvent, or excessive grease.
13. Never attempt to adjust ASME safety valve. Keep safety valve free from paint and other
accumulations.
14. Tanks rust from moisture build-up, which weakens the tank. Make sure to drain tank regularly and
inspect periodically for unsafe conditions such as rust formation and corrosion.
15. Fast moving air will stir up dust and debris which may be harmful. Release air slowly when
draining moisture or depressurizing the compressor system.
SAFETY INFORMATION
4
Risk of Explosion. Never attempt
to repair or modify a tank! Welding,
drilling or any other modi cation
will weaken the tank resulting in
damage from rupture or explosion.
Always replace worn, cracked or
damaged tanks.
DANGER
WARNING
Risk of Fire. Motors, electrical
equipment and controls can cause
electrical arcs that will ignite a
ammable gas or vapor. Never
operate or repair in or near a
ammable gas or vapor. Never
store ammable liquids or gases in
the vicinity of the compressor.
DANGER
Risk of Personal Injury. This compressor/
pump is NOT equipped and should NOT be
used “as is” to supply breathing quality air. For
any application of air for human consumption,
you must fit the air compressor/pump with
suitable in-line safety and alarm equipment.
This additional equipment is necessary
to properly filter and purify the air to meet
minimal specifications for Grade D breathing
as described in Compressed Gas Association
Commodity Specification G 7.1, OSHA 29
CFR 1910. 134, and/or Canadian Standards
Associations (CSA).
DISCLAIMER OF WARRANTIES
In the event the compressor is used for the
purpose of breathing air application and
proper in-line safety and alarm equipment is
not simultaneously used, existing warranties
are void, and the Manufacturer disclaims any
liability whatsoever for any loss, personal injury
or damage.
WARNING
Risk of Explosion. Never use plastic (PVC)
pipe for compressed air. Serious injury or
death could result.
WARNING
Risk of Personal Injury and/or Equipment
Damage. Never install a shut-off valve
between the compressor pump and the tank.
kobalttools.com
SAFETY INFORMATION
5
WARNING
Risk of Fire. Do not spray
ammable materials in vicinity
of open ame or near ignition
sources including the compressor
unit.
SPRAYING PRECAUTIONS
1. Do not smoke when spraying paint, insecticides, or other flammable substances.
2. Use a face mask/respirator when spraying and spray in a well-ventilated area to prevent health
and fire hazards.
3. Do not direct paint or other sprayed material at the compressor. Locate compressor as far away
from the spraying area as possible to minimize overspray accumulation on the compressor.
4. When spraying or cleaning with solvents or toxic chemicals, follow the instructions provided by
the chemical manufacturer.
CAUTION
Do Not Overpressure. See compressor
speci cation decal for maximum operating
pressure. Do not operate with pressure switch
or safety valves set higher than the maximum
operating pressure.
NOTICE
Unit Care and Maintenance. Drain liquid from
tank daily.
GENERAL SAFETY (Continued)
Risk of Personal Injury.
Compressor parts may be hot
even if the unit is stopped.
CAUTION
WARNING
Risk of Personal Injury. Never
operate compressor without a
beltguard. This unit can start
automatically without warning.
Personal injury or property
damage could occur from contact
with moving parts.
WARNING
Risk of Explosion. An ASME code safety
relief valve with a setting no higher than
the maximum allowable working pressure
(MAWP) MUST be installed in the tank for
this compressor. The ASME safety valve must
have suf cient ow and pressure ratings to
protect the pressurized components from
bursting.
kobalttools.com
6
PACKAGE CONTENTS
PART DESCRIPTION QTY.
A Pressure Switch - AUTO/OFF Switch - In the AUTO position, the compressor
shuts off automatically when tank pressure reaches the maximum preset pressure.
After air is used from the tank and drops to a preset low level, the pressure switch
automatically turns the motor back on. In the OFF position, the compressor will not
operate. This switch should be in the OFF position when connecting or disconnecting
the power from the unit.
When the pressure switch turns the motor off you will hear air leaking out of the
pressure switch unloader valve for a short time. This releases the air pressure from
the discharge tube and allows the compressor to restart easier.
1
B ASME Safety Valve - This valve automatically releases air if the tank pressure
exceeds the preset maximum.
1
C Discharge tube - This tube carries compressed air from the pump to the check valve.
This tube becomes very hot during use. To avoid the risk of severe burns, never touch
the discharge tube.
1
A
B
C
D
E
F
G
H
I
J
K
kobalttools.com
7
PACKAGE CONTENTS
WARNING
Risk of Personal Injury. Do not operate unit
if damaged during shipping, handling or use.
Damage may result in bursting and cause
injury or property damage.
Before beginning installation and/or assembly of product, make sure all parts are present. Compare
parts with package contents list. If any part is missing or damaged, do not attempt to assemble or use
the product. Contact customer service for replacement parts and assistance.
PREPARATION
PART DESCRIPTION QTY.
D Check valve - One-way valve that allows air to enter the tank, but prevents air in the
tank from flowing back into the compressor pump.
1
E Belt Guard - Covers the belt, motor pulley and flywheel. 1
F Tank Drain Valve - This valve is located on the bottom of the tank. Use this valve to
drain moisture from the tank daily to reduce the risk of corrosion.
1
G Tank Pressure Gauge - Indicates amount of air pressure stored in tank. 1
H Hose Pressure Gauge - Indicates amount of air pressure in hose used to operate
tools. This pressure is increased or decreased by the regulator.
1
I Regulator - The regulator controls the amount of air pressure released at the hose
outlet.
1
J Air Filter - Keeps debris and particulates out of the air flowing into the compressor. 1
K Breather - Vent for crankcase. 1
HARDWARE CONTENTS (shown actual size)
AA BB CC
5/16 inch x
18 Spinlock Nut
Qty. 2
5/16 inch Washer
Qty. 2
Rubber Foot
Qty. 2
kobalttools.com
ASSEMBLY INSTRUCTIONS
8
1. Unbolt the unit from the shipping skid. Use a
ratchet with a 9/16 inch socket. Remove the
unit from the skid. Discard shipping hardware
once removed.
2. Install rubber feet with nuts and washers.
Hardware Used
Nut
AA
x2
BB
Washer x2
PREPARATION
Estimated Installation and Assembly Time: 20 minutes
Tools Required for Installation and Assembly (not included): Safety Glasses; Work Gloves; 9/16 inch
Socket and Ratchet; Adjustable Wrench
ADDITIONAL PARTS REQUIRED FOR USE [not included]
Parts - available at local hardware store.
1. Air Hose
2. Pipe Thread Sealant
CC
Rubber Foot x2
1
Shipping
Bolt
Shipping
Bracket
Shipping
Bolt
2
AA
BB
CC
kobalttools.com
9
ASSEMBLY INSTRUCTIONS
3. Remove cap from pump.
4. Install breather. Install air
lter.
3
Cap
4
Air Filter
Breather
kobalttools.com
ASSEMBLY INSTRUCTIONS
10
LUBRICATION
CAUTION
Inspect Before Use. Check for proper oil level
before operating!
Remove cap from oil fill opening. See Figure
1. Install breather (found in parts bag with this
manual). See Figure 2. Check oil level; some
models are shipped with oil in the pump. See
specification label on compressor pump for the
proper oil capacity and oil type.
OIL INFORMATION
Kobalt Air Compressor Oil SKU 221008
Kobalt Synthetic Blend Oil SKU 221009
Mobil 1
®
synthetic 10W30
Oil Capacity 8.5 ounces
Do not use regular automotive oil. Additives in
regular motor oil can cause valve deposits and
reduce pump life. For maximum pump life, drain
and replace oil after the first hour of run time.
This pump has an oil sight glass as shown
in Figure 2. Oil level can be monitored and
maintained as shown in Figure 3.
1
Cap
2
Breather
Oil Fill Area
Oil Drain
Plug
Sight
Glass
3
Sight Glass
Full
Low
kobalttools.com
11
ASSEMBLY INSTRUCTIONS
ELECTRICAL INFORMATION
Risk of Shock. Improperly
grounded motors are shock
hazards. Make sure all the
equipment is properly grounded.
DANGER WARNING
Risk of Personal Injury or Damage to
Personal Property. Overheating, short
circuiting and re damage will result from
inadequate wiring.
NOTICE
Unit care and maintenance. Damage to the
motor from improper electrical voltage or
connection will void the warranty.
WARNING
Risk of Explosion. Disconnect,
tag and lock out power source,
then release all pressure from the
system before attempting to install,
service, relocate or perform any
maintenance.
Risk of Shock. Improper
installation of the grounding plug
is able to result in a risk of electric
shock. When repair or replacement
of the cord or plug is required, do
not connect the grounding wire
to either at blade terminal. The
wire with insulation having an
outer surface that is green with
or without yellow stripes is the
grounding wire.
WARNING
Do not use an extension cord, use a longer air hose.
The 120 volt, 15 amp units can be operated on a 120 volt 15 amp circuit under the following conditions:
1. No other electrical appliances or lights are connected to the same branch circuit.
2. Voltage is 120 Volts.
3. Circuit is equipped with a 15 amp circuit breaker or a 15 amp slow blow fuse type T (For Canada
use Type D).
4. The length of copper wire between the outlet and circuit breaker is not longer than 40 feet of
14 AWG or 70 feet of 12 AWG.
kobalttools.com
ASSEMBLY INSTRUCTIONS
12
This product is for use on a nominal 120 volt
circuit and has a grounding plug similar to the
plug illustrated in Figure 1. If the listed conditions
cannot be met or if nuisance tripping of the
current protection device occurs, it may be
possible to operate the compressor from a 120
volt 20 amp circuit. See Figure 1.
Check motor data plate for 240 volt compatability.
A 240 volt unit must be operated on a 240 volt
circuit. The cord must only plug into a 240 volt
grounded outlet and may require a new cord and
plug. See Figure 2.
Check with a qualified electrician or serviceman when the grounding instructions are not completely
understood, or when in doubt as to whether the product is properly grounded. Do not modify the plug
provided; if it does not fit the outlet, have the proper outlet installed by a qualified electrician. Only
connect the product to an outlet having the same configuration as the plug. Do not use an adapter with
this product.
GROUNDING
This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric current. This product is equipped with a cord
having a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet
that is properly installed and grounded in accordance with all local codes and ordinances. Do not use
grounding adapter.
1
Ground
Pin
Grounded
Outlet
Outlet - 120V / 15A
Outlet - 120V / 20A
2
Grounded
Outlet
Ground
Pin
Outlet - 240V
kobalttools.com
13
OPERATING INSTRUCTIONS
1. Check oil level per the Lubrication Section of this
manual.
2. Open the bottom tank drain valve (see Figure 1).
Turn outlet valve to open air flow.
3. Plug unit in.
START-UP / BREAK-IN PROCEDURE
WARNING
Risk of Personal Injury. Never disconnect
threaded joints with pressure in tank!
WARNING
Risk of Personal Injury. Do not attach air
tools to open end of the hose until start-up is
completed and the unit checks okay.
1
4. Move pressure switch to the AUTO position to run the
unit (see Figure 2).
5. Run the unit for thirty (30) minutes at zero (0) psi
(under no load) to break in pump parts.
6. Move the pressure switch lever or knob to OFF
and turn tank drain valve to shut off air flow. The
compressor is now ready for use.
7. Change oil after first fifty (50) hours of operation.
Then perform oil changes every three (3) months.
2
COMPRESSOR USE
It is extremely important to operate the compressor in a clean, well-ventilated area where the
surrounding air temperature will not be more than 100°F. Do not locate the compressor air inlet near
steam, paint spray, sandblast areas or any other source of contamination.
kobalttools.com
OPERATING INSTRUCTIONS
14
In the AUTO position, the compressor pumps air
into the tank. When a shut-off (preset “cut-out”)
pressure is reached, the compressor automatically
shuts off.
If the compressor is left in the AUTO position
and air is depleted from the tank by use of a
tire chuck, tool, etc., the compressor will restart
automatically at its preset “cut-in” pressure. When
a tool is being used continuously, the compressor
will cycle on and off automatically.
In the OFF position, the compressor will not
operate.
Drain Tank. Disconnect, tag, unplug and lock out
power source; release pressure. Drain moisture
from tank by opening drain valve underneath tank
(See Figure 1).
NOTICE
Unit care and maintenance. Drain liquid from
tank daily.
ON/OFF CYCLING OF COMPRESSOR
WARNING
Risk of Bursting. Drain tank every day to
prevent corrosion and possible injury due to
tank damage. Do not operate drain with more
than 40 psi in tank or drain valve may be
damaged. Drain tank of moisture daily using
the drain valve in the bottom of the tank.
MOISTURE IN COMPRESSED AIR
Moisture in compressed air will form into droplets as it comes from an air compressor pump.
When humidity is high or when a compressor is in continuous use for an extended period of time,
this moisture will collect in the tank. When using a paint spray or sandblast gun, this water will
be carried from the tank through the hose, and out of the gun as droplets mixed with the spray
material.
IMPORTANT: This condensation will cause water spots in a paint job, especially when spraying
other than water based paints. If sandblasting, it will cause the sand to cake and clog the gun,
rendering it ineffective. A lter in the air line, located as near to the gun as possible, will help
eliminate this moisture.
1
Bottom Drain Valve
kobalttools.com
15
CARE AND MAINTENANCE
WARNING
Risk of Explosion. Disconnect,
tag and lock out power source,
then release all pressure from the
system before attempting to install,
service, relocate or perform any
maintenance.
All repairs should be performed by an authorized service representative.
For efficient operation, perform the following maintenance.
NOTICE
Unit care and maintenance. Drain liquid from
tank daily.
1. Disconnect, tag, unplug and lock out power
source; clean debris from motor, flywheel,
tank, air lines and pump cooling fins.
2. Maintain proper oil level. Refer to Lubrication
section for details.
3. Change oil.
a. Allow compressor to run and warm up
oil. Disconnect, tag and lock out power
source.
b. Position a pan under pump.
c. Remove oil drain plug (See Figure 1).
Allow oil to collect in pan.
d. Replace drain plug, fill pump to full level
(See Figure 1). See Lubrication section of
this manual.
4. Drain Tank. Disconnect, tag and lock out
power source; release pressure. Drain
moisture from tank by opening drain valve
underneath tank (See Figure 2).
5. Check air filter to be sure it is clean. Replace
filter if filter is dirty.
2
1
Oil Fill Area
Oil Drain
Plug
kobalttools.com
16
CARE AND MAINTENANCE
6. Check the safety valve by performing the following
steps:
a. Restore power to unit; turn pressure switch to the
AUTO position. Run until unit reaches 90 psi.
Turn pressure switch to OFF position.
b. Wearing safety glasses and hearing protection,
pull the ring on the safety valve to release
pressure from compressor tank. Protect yourself
from fast-moving air being released; do not allow
fast-moving air to be directed toward your face
(See Figure 3).
c. The safety valve should automatically close at
approximately 40-50 psi. If the safety valve does
not allow air to be released when you pull on the
ring, or if it does not close automatically, it MUST
be replaced.
7. Check belt for signs of excessive wear. If belt shows
signs of wear, replace it. Check belt for proper
tension / alignment.
3
MAINTENANCE SCHEDULE
OPERATION DAILY WEEKLY MONTHLY 3 MONTHS
CHECK OIL LEVEL
DRAIN TANK
CHECK AIR FILTER
CHECK SAFETY VALVE
CLEAN UNIT
CHECK BELT TIGHTNESS
CHANGE OIL*
* Change oil after rst fty (50) hours of operation then perform oil changes every three (3)
months.
TECHNICAL SERVICE
For information regarding the operation or repair of this product, please call 1-888-3KOBALT
(1-888-356-2258).
Low discharge
pressure
1. Air demand exceeds
pump capacity
1. Reduce air demand or use a compressor with
more capacity.
2. Restricted air intake 2. Clean or replace the air filter element.
3. Air leaks (fittings,
tubing on compressor,
or plumbing outside of
system)
3. Listen for escaping air. Apply soap solution to
all fittings and connections. Bubbles will appear
at points of leakage. Tighten or replace leaking
fittings or connections. Use pipe thread sealant.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
kobalttools.com
17
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Low discharge
pressure
(Continued)
4. Blown gaskets 4. Replace any gaskets proven faulty on
inspection.
5. Leaking or damaged
valves
5. Remove head and inspect for valve breakage,
misaligned valves, damaged valve seats, etc.
Replace defective parts and reassemble.
CAUTION
Unit care and maintenance. Install a new
head gasket each time the head is removed.
Excessive noise
(knocking)
1. Loose motor pulley or
flywheel
1. Tighten pulley / flywheel clamp bolts and set-
screws.
2. Loose fasteners on pump
or motor
2. Tighten fasteners.
3. Lack of oil in crankcase 3. Check for proper oil level; if low, check for
possible damage to bearings. Dirty oil can
cause excessive wear.
4. Worn connecting rod 4. Replace connecting rod. Maintain oil level and
change oil more frequently.
5. Worn piston pin bores 5. Remove piston assemblies from the
compressor and inspect for excess wear.
Replace excessively worn piston pin or pistons,
as required. Maintain oil level and change oil
more frequently.
6. Piston hitting the valve
plate
6. Remove the compressor head and valve plate
and inspect for carbon deposits or other foreign
matter on top of piston. Replace head and
valve plate using new gasket. See Lubrication
section for recommended oil.
7. Noisy check valve in
compressor system
7. Replace check valve.
Risk of Explosion. Do not
disassemble check valve with air
pressure in tank.
DANGER
Large quantity of oil
in the discharge air
NOTE: In an oil-
lubed compressor
there will always be
a small amount of
oil in the air stream.
1. Worn piston rings 1. Replace with new rings. Maintain oil level and
change oil more frequently.
2. Compressor air intake
restricted
2. Clean or replace filter. Check for other
restrictions in the intake system.
3. Excessive oil in
compressor
3. Drain down to full level.
4. Wrong oil viscosity 4. Use Mobil 1
®
10W-30 or full synthetic.
kobalttools.com
TROUBLESHOOTING
18
Water in discharge
air / tank
Normal operation. The
amount of water increases
with humid weather
1. Drain tank more often. At least daily.
2. Add a filter to reduce the amount of water in the
air line.
Motor hums and
runs slowly or not
at all
1. Low voltage 1. Check incoming voltage. It should be
approximately 230 volts. Motor will not run
properly on 208 volts. Low voltage could
be due to wires (from electrical source to
compressor) being too small in diameter and /
or too long. Have a qualified electrician check
these conditions and make repairs as needed.
2. Use of extension cord 2. Do not use an extension cord. Use longer air
hose with larger diameter.
3. Too many devices on
same circuit
3. Limit the circuit to the use of compressor only
4. Loose electrical
connections
4. Check all electrical connections.
5. Malfunctioning pressure
switch - contacts will not
close
5. Replace pressure switch.
6. Malfunctioning check
valve
6. Replace check valve.
Risk of Explosion. Do not
disassemble check valve with air
pressure in tank.
DANGER
7. Defective unloader valve
on pressure switch
7. Replace unloader valve.
8. Defective motor
capacitor(s)
8. Replace capacitor(s).
9. Defective motor 9. Replace motor.
Reset mechanism
cuts out repeatedly
or circuit breaker
trips repeatedly
1. Lack of proper
ventilation / room
temperature too high
1. Move compressor to well-ventilated area.
2. Too many devices on
same circuit
2. Limit the circuit to the use of only the air
compressor.
3. Restricted air intake 3. Clean or replace filter element.
4. Loose electrical
connection
4. Check all electrical connections.
5. Pressure switch shut-off
pressure set too high
5. Replace pressure switch.
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
kobalttools.com
19
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Reset mechanism
cuts out repeatedly
or circuit breaker
trips repeatedly
(Continued)
6. Malfunctioning check
valve
6. Replace check valve.
Risk of Explosion. Do not
disassemble check valve with air
pressure in tank.
DANGER
7. Defective unloader valve
on pressure switch
7. Replace unloader valve.
8. Defective motor
capacitor(s)
8.Replace capacitor(s).
9. Malfunctioning motor 9. Replace motor.
Tank does not hold
pressure when
compressor is off
and the shut off
valve is closed
1. Air leaks (fittings, tubing
on compressor, or
plumbing outside system)
1. Check all connections with soap and water
solution. Tighten; or remove and apply sealant
to threads, then reassemble.
2. Worn check valve 2. Replace check valve.
Risk of Explosion. Do not
disassemble check valve with air
pressure in tank.
DANGER
3. Check tank for cracks or
pin holes
3. Replace tank. Never repair a damaged tank.
Pressure switch
continuously
blows air out the
unloader valve
Malfunctioning check valve Replace the check valve if the unloader valve on
the pressure switch bleeds off constantly when
unit shuts off.
Risk of Explosion. Do not
disassemble check valve with air
pressure in tank.
DANGER
Excessive vibration 1. Loose fasteners on pump
or motor
1. Tighten fasteners.
2. Belt needs replaced 2. Replace with correct size.
3. Belt alignment 3. Align flywheel and pulley.
kobalttools.com
TROUBLESHOOTING
20
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Pressure switch
does not release
air when the unit
shuts off
Malfunctioning unloader
valve on pressure switch
Replace the unloader valve if it does not release
the pressure for a short period of time when the
unit shuts off.
Risk of Explosion. Do not
disassemble unloader valve with
air pressure in tank.
DANGER
WARRANTY
1. DURATION: From the date of purchase by the original purchaser as follows: Three Years.
2. WHO GIVES THIS WARRANTY: Campbell Hausfeld / Scott Fetzer Company, 100 Production
Drive, Harrison, Ohio, 45030.
3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for
purposes of resale) of the compressor.
4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: This air compressor.
5. WHAT IS COVERED UNDER THIS WARRANTY: Parts and Labor to remedy substantial
defects due to material and workmanship during the first year of ownership with the exceptions
noted below. Parts only to remedy substantial defects due to material and workmanship during
remaining term of coverage with exceptions noted below.
6. WHAT IS NOT COVERED UNDER THIS WARRANTY:
A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR
PURPOSE ARE LIMITED FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN
THE DURATION. If the compressor is used for commercial, industrial or rental purposes, the
warranty will apply for ninety (90) days from the date of purchase. Four cylinder single stage
compressors and two-stage compressors are not limited to a ninety (90) day warranty when
used in commercial or industrial applications. Some States do not allow limitations on how
long an implied warranty lasts, so the above limitations may not apply to you
B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE
THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE
CAMPBELL HAUSFELD PRODUCT. Some States do not allow the exclusion or limitations of
incidental or consequential damages, so the above limitation or exclusion may not apply to
you.
C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate
products in accordance with instructions provided in the owner’s manual(s) supplied with
compressor.
D. Pre-delivery service, e.g. assembly, oil or lubricants, and adjustment.
E. Items or service that is normally required to maintain the product, i.e. lubricants, filters and
gaskets, etc.
F. Gasoline engines and components are expressly excluded from coverage under this limited
warranty. The Purchaser must comply with the warranty given by the engine manufacturer
which is supplied with the product
kobalttools.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88

Kobalt VT6389 Manuel utilisateur

Catégorie
Compresseurs d'air
Taper
Manuel utilisateur

dans d''autres langues