Hitachi RAC-24G5 Manuel utilisateur

ENGLISHDEUTSCHFRANÇAIS

SPLIT TYPE

INDOOR UNIT/OUTDOOR UNIT

MODEL

RAS-24G5 / RAC-24G5

OUTDOOR UNIT

INDOOR UNIT

RAS-24G5

RAC-24G5

RAS-24G5 DD0004446D (1)_EN.indd 1 7/5/11 9:13 AM

– 2 –

●

Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit.

●

Pay special attention to signs of “

!

Warning” and “

!

Caution”. The “Warning” section contains matters which,

if not observed strictly, may cause death or serious injury. The “Caution” section contains matters which may result

in serious consequences if not observed properly. Please observe all instructions strictly to ensure safety.

●

The sign indicate the following meanings.

●

Please keep this manual after reading.

Make sure to connect earth line.

Indicates the instructions that must be followed.

The sign in the ﬁ gure indicates prohibition.

SAFETY PRECAUTION

PRECAUTIONS DURING OPERATION

●

Avoid an extended period of direct air ﬂ ow for your health.

W

A

R

N

I

N

G

!

●

Do not insert a ﬁ nger, a rod or other objects into the air outlet or inlet. As the fan is rotating at a

high speed, it will cause injury. Before cleaning, be sure to stop the operation and turn the breaker

OFF.

●

During thunder storm, disconnect and turn off the circuit breaker.

●

Do not use any conductor as fuse wire, this could cause fatal accident.

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

●

Should abnormal situation arises (like burning smell), please stop operating the unit and turn off

the circuit breaker. Contact your agent. Fault, short circuit or ﬁ re may occur if you continue to

operate the unit under abnormal situation.

●

Please contact your agent for maintenance. Improper self maintenance may cause electric shock

and ﬁ re.

●

Please contact your agent if you need to remove and reinstall the unit. Electric shock or ﬁ re may

occur if you remove and reinstall the unit yourself improperly.

●

If the supply cord is damaged, it must be replaced by the special cord obtainable at

authorized service/parts centers.

W

A

R

N

I

N

G

!

WARNING

PRECAUTIONS DURING INSTALLATION

●

Do not reconstruct the unit.

Water leakage, fault, short circuit or ﬁ re may occur if you reconstruct the unit by yourself.

●

Please ask your sales agent or qualiﬁ ed technician for the installation of your unit. Water

leakage, short circuit or ﬁ re may occur if you install the unit by yourself.

●

Please use earth line.

Do not place the earth line near water or gas pipes, lightning-conductor, or the earth line

of telephone. Improper installation of earth line may cause electric shock.

●

Be sure to use the speciﬁ ed piping set for R410A. Otherwise, this may result

in broken copper pipes or faults.

●

A circuit breaker should be installed depending on the mounting site of the unit. Without a

circuit breaker, the danger of electric shock exists.

●

Do not install near location where there is ﬂ ammable gas. The outdoor unit may catch ﬁ re

if ﬂ ammable gas leaks around it.

●

Please ensure smooth ﬂ ow of water when installing the drain hose.

CAUTION

!

I Manual RAS-18G5_3 languages.indb 2 3/3/2011 10:28:22 AM

ENGLISH

– 3 –

PRECAUTIONS DURING OPERATION

●

Do not attempt to operate the unit with wet hands, this could cause fatal

accident.

●

When operating the unit with burning equipments, regularly ventilate the

room to avoid oxygen insufﬁ ciency.

●

Do not direct the cool air coming out from the air-conditioner panel to face

household heating apparatus as this may affect the working of apparatus

such as the electric kettle, oven etc.

●

Do not use any aerosol or hair sprays near the indoor unit. This chemical

can adhere on heat exchanger ﬁ n and blocked the evaporation water ﬂ ow

to drain pan. The water will drop on tangential fan and cause water splashing

out from indoor unit.

●

Please ensure that outdoor mounting frame is always stable, firm and

without defect. If not, the outdoor unit may collapse and cause danger.

●

Do not splash or direct water to the body of the unit when cleaning it as this

may cause short circuit.

●

When operating the unit with the door and windows opened, (the room humidity is always above

80%) and with the air deﬂ ector facing down or moving automatically for a long period of time,

water will condense on the air deﬂ ector and drips down occasionally. This will wet your furniture.

Therefore, do not operate under such condition for a long time.

●

If the amount of heat in the room is above the cooling capability of the unit (for example: more

people entering the room, using heating equipments and etc.), the preset room temperature cannot

be achieved.

●

This appliance is not intended for use by young children or inﬁ rm person unless they have been

adequately supervised by a responsible person to ensure that they can use the appliance safely.

●

Young children should be supervised to ensure that they do not play with the appliance.

●

Do not climb on the outdoor unit or put objects on it.

●

Please switch off the unit and turn off the circuit breaker during cleaning, the

high-speed fan inside the unit may cause danger.

●

Turn off the circuit breaker if the unit is not to be operated for a long period.

C

A

U

T

I

O

N

!

●

The product shall be operated under the manufacturer speciﬁ cation and

not for any other intended use.

●

Do not put water container (like vase) on the indoor unit to avoid water

dripping into the unit. Dripping water will damage the insulator inside the unit

and causes short-circuit.

●

Do not place plants directly under the air ﬂ ow as it is bad for the plants.

I Manual RAS-18G5_3 languages.indb 3 3/3/2011 10:28:22 AM

– 2 –

INDOOR UNIT

NAMES AND FUNCTIONS OF EACH PART

Pre-ﬁ lter

To prevent dust from coming into the indoor unit.

(Refer Instruction Manual)

Front panel

Indoor unit indicators

Light indicator showing the operating condition.

(Refer page 3)

Horizontal deﬂ ector

●

Vertical deﬂ ector

(Air Outlet)

Remote controller

Send out operation signal to the indoor unit. So as to

operate the whole unit.

(Refer Instruction Manual)

OUTDOOR UNIT

Drain pipe

Condensed water drain to outside.

Connecting cord and insulation pipe for piping

Air inlet (Back and Left side)

Air outlet

MODEL WIDTH (mm) HEIGHT (mm)

DEPTH (mm)

RAS-24G5 1030 295

207

RAC-24G5 850 650

298

MODEL NAME AND DIMENSIONS

RAS-24G5 DD0004446D (1)_EN.indd 2 7/5/11 9:13 AM

– 3 –

ENGLISH

OPERATION INDICATOR

● This figure shows the opening condition of

front panel. Refer to page 14 in relation to how

to open or close the front panel.

OPERATION LAMP

This lamp lights during operation.

TIMER LAMP

This lamp lights when the timer is working.

FILTER LAMP

When the device is operated for a total of about 200

hours, the FILTER lamp lights to indicate that it is time

to clean the ﬁ lter. The lamp goes out when the “

(AUTO SWING)” button is pressed while the device is on

“STANDBY MODE”.

TEMPORARY SWITCH

Use this switch to start and stop when the remote controller does not work.

● By pressing the temporary switch, the operation is done in previously set operation mode.

● When the operation is done using the temporary switch after the power source is turned off and turn on again,

the operation is done in automatic mode.

INDOOR UNIT INDICATORS

RAS-24G5 DD0004446D (1)_EN.indd 3 7/5/11 9:13 AM

– 4 –

NAMES AND FUNCTIONS OF REMOTE CONTROL UNIT

REMOTE CONTROLLER

This controls the operation of the indoor unit. Signal range to reach indoor unit is about 7 meters. If

inverter lamp is used, the range of control may be shorter.

This unit can be ﬁ xed on a wall using the ﬁ xture provided. Before ﬁ xing it, make sure the indoor unit

can be controlled from the remote controller.

● Transmission sign

The transmission sign blinks when a signal is sent.

● Display

This indicates the room temperature selected, timer status, function

and intensity of circulation selected.

● CIRCULATION button

Use this button to set air circulation in the room or start operation.

● DEHUMIDIFYING button

Use this button to reduce humidity in the room or start operation.

● COOLING button

Use this button to set cooling mode in the room or start operation.

● RESET button

● STOP button

Press this button to stop operation only.

● SLEEP button

Use this button to set the sleep timer.

● FAN SPEED selector

This determines the fan speed. Each time you press this button,

the intensity of circulation will change from (AUTO) to (HI)

to (MED) to (LOW)

● AUTO SWING button

Controls the angle of the horizontal air deﬂ ector.

● TEMPERATURE button

Use this button to raise or lower the temperature setting. (Keep

pressed, and the value will change more quickly.)

● OFF-TIMER button Select the turn OFF time.

● ON-TIMER button Select the turn ON time.

Precautions for Use

● Do not put the remote controller in the following places.

● In direct sunlight.

● In the vicinity of a heater.

● Handle the remote controller carefully. Do not drop it on the

ﬂ oor, and protect it from water.

● Once the outdoor unit stops, it will not restart for about 3

minutes (unless you turn the power switch off and on or unplug

the power cord and plug it in again).

This is to protect the device and does not indicate a failure.

CIRCULATION / START

DEHUMIDIFY / START

COOLING / START

FAN

FAN SPEED

LOW

MED

HI

SLEEP TIMER

STOP

TIMER SELECTOR

ON TIMER

OFF TIMER

AUTO SWING

I Manual RAS-18G5_3 languages.indb 4 3/3/2011 10:28:23 AM

ENGLISH

– 5 –

COOLING OPERATION

Use the device for cooling when the outdoor temperature is 21 ~ 43°C.

If indoor humidity is very high (over 80%), some dew may form on the air outlet grille of the indoor unit.

Press the button so that the display indicates (COOL).

Cooling operation starts with a beep.

The cooling function does not start if the temperature setting

is higher than the current room temperature (even though

the (OPERATION) lamp lights). The cooling function will

start as soon as you set the temperature below the current

room temperature.

Set the desired FAN SPEED with the (FAN SPEED) button

(the display indicates the setting).

(AUTO) : The FAN SPEED is HI at ﬁ rst and varies to

MED or LOW automatically when the preset

temperature has been reached.

(HI) : Hi fan speed mode.

(MED) : Medium fan speed mode.

(LOW) : Low fan speed mode.

Set the desired room temperature with the TEMPERATURE

button (the display indicates the setting).

The range of 25 ~ 28°C is recommended as

the room temperature for cooling.

If the temperature setting is 27°C, the room

temperature will be controlled at around 27°C.

The temperature setting and the actual room temperature may

vary somewhat depending on conditions.

Press the

(STOP) button to stop operation.

■ As the settings are stored in memory in the remote controller, you

only have to press the (COOLING) button to repeat the same

setting next time.

STOP

I Manual RAS-18G5_3 languages.indb 5 3/3/2011 10:28:24 AM

– 6 –

DEHUMIDIFYING OPERATION

Use the device for dehumidifying when the room temperature is over 16°C.

When it is under 15°C, the dehumidifying function will not work.

■ Dehumidifying Function

When the room temperature is higher than the temperature setting: The device will dehumidify the

room and reducing the room temperature to the preset level.

When the room temperature is lower than the temperature setting: Dehumidifying will be performed at

the temperature setting slightly lower than the current room temperature, regardless of the temperature

setting. The function will stop (the indoor unit will stop emitting air) as soon as the room temperature

becomes lower than the setting temperature.

■ As the settings are stored in memory in the remote controller, you

only have to press the

(DEHUMIDIFY) button next time.

Set the desired room temperature with the TEMPERATURE

button (the display indicates the setting).

The range of 20 ~ 26˚C is recommended as

the room temperature for dehumidifying.

Press the button so that the display indicates

(DEHUMIDIFY).

Dehumidifying operation starts with a beep.

The FAN SPEED is set at LOW automatically.

The FAN SPEED button does not work.

Press the (STOP) button to stop operation.

STOP

I Manual RAS-18G5_3 languages.indb 6 3/3/2011 10:28:24 AM

ENGLISH

– 7 –

CIRCULATION OPERATION

Press the button so that the display indicates

(CIRCULATION).

Circulating operation starts with a beep.

Press the FAN SPEED button and select the desired FAN

SPEED (the display indicates your choice).

Press the temperature control button to set to the desired

temperature.

■ As the settings are stored in memory in the remote controller,

you only have to press the

(CIRCULATION) button next time.

Press the (STOP) button to stop operation.

STOP

■ Circulation Function

● During circulation operation, compressor does not run and there is no cooling operation with only indoor

fan running.

● When the setting temperature is higher than room temperature, indoor fan will stop running.

I Manual RAS-18G5_3 languages.indb 7 3/3/2011 10:28:25 AM

– 8 –

HOW TO SET THE SLEEP TIMER

Sleep Timer: The device will continue working for the designated

number of hours and then turn off.

Point the signal window of the remote controller toward the indoor

unit, and press the SLEEP button.

The timer information will be displayed on the remote controller.

The TIMER lamp lights with a beep from the indoor unit.

Press the (SLEEP) button, and the display changes as shown below.

Mode

Sleep timer

Indication

1 hour 2 hours 3 hours 7 hours

Sleep timer off

44 44

1

Cooling

“ ”

and

dehumidifying

“ ”

Explanation of the sleep timer

The device will control the FAN SPEED and room temperature automatically

so as to be quiet and good for people’s health.

You can set the sleep timer to turn off after 1, 2, 3 or 7 hours. The FAN

SPEED and room temperature will be controlled as shown below.

Function Operation

The room temperature will

be controlled 2°C above the

temperature and the FAN

SPEED will be set to LOW

setting 1 hour after the setting

of the sleep timer.

SLEEP

Sleep

timer set

2 hours

later

1 hour later 3 hours later

7 hours later

Operation with the sleep timer

I Manual RAS-18G5_3 languages.indb 8 3/3/2011 10:28:25 AM

ENGLISH

– 9 –

HOW TO SET THE TIMER

■ ON Timer and OFF Timer are available.

OFF TIME setting

● Select the OFF TIME by pressing the (OFF) Button.

● Setting time will change according to the below sequence

when you press the button.

OFF Timer Reservation

■ Operation stop at setting time

ON TIME setting

● Select the ON TIMER by pressing the (ON) Button.

● Setting time will change according to the below sequence.

ON Timer Reservation

■ Operation will start for setting

temperature at setting time (The

starting time may different depend

on the room temperature and set

temperature).

1 hour interval

(CANCEL OFF TIMER)

1 hour interval

(CANCEL ON TIMER)

I Manual RAS-18G5_3 languages.indb 9 3/3/2011 10:28:26 AM

– 10 –

Adjustment of the conditioned air in the upward and

downward directions.

The horizontal air deﬂ ector is automatically set to the

proper angle suitable for each operation. The deﬂ ector

can be swung up and down continuously and also set

to the desired angle using the “

(AUTO SWING)”

button.

ADJUSTING THE AIR DEFLECTORS

Adjustment of the conditioned air to the left and

right.

Hold the vertical air deﬂ ector as shown in the ﬁ gure

and adjust the conditioned air to the left or right.

● If the “ (AUTO SWING)” button is pressed once, the

horizontal air deﬂ ector swings up and down. If the button

is pressed again, the deﬂ ector stops in its current position.

Several seconds (about 6 seconds) may be required

before the deﬂ ector starts to move.

● In “Cooling” operation, do not keep the horizontal air

deﬂ ector swinging for a long time. Some dew may form

on the horizontal air deﬂ ector and dew may drop.

I Manual RAS-18G5_3 languages.indb 10 3/3/2011 10:28:27 AM

ENGLISH

– 11 –

When using the remote control, if there is no response from the air conditioner unit and/or the remote

control has fading and dim displays, the batteries in the remote control device need to be removed and

replaced with new ones

HOW TO EXCHANGE THE BATTERIES IN THE REMOTE CONTROLLER

Remove the cover as shown in the ﬁ gure and

take out the old batteries.

Install the new batteries.

The direction of the batteries should match the

marks in the case.

1. Do not use new and old batteries, or different kinds

of batteries together.

2. Take out the batteries when you do not use the remote

controller for 2 or 3 months.

3. Use high quality and high performance AAA batteries

to avoid short operating life and electrolyte leakages.

!

CAUTION

I Manual RAS-18G5_3 languages.indb 11 3/3/2011 10:28:27 AM

– 12 –

Suitable Room Temperature Install curtain or blinds

Ventilation Effective Usage Of Timer

Do Not Forget To Clean The Air Filter

Please Adjust Suitable Temperature

For Baby And Children

It is possible

to reduce heat

entering the

room through

windows.

At night, please use the “OFF or ON timer

operation mode”, together with your wake

up time in the morning. This will enable you

to enjoy a comfortable room temperature.

Please use the timer effectively.

Dusty air ﬁ lter will reduce the air volume

and the cooling efﬁ ciency. To prevent from

wasting electric energy, please clean the ﬁ lter

every 2 weeks.

Please pay attention to the room temperature

and air ﬂ ow direction when operating the unit

for baby, children and old folks who have

difﬁ culty in movement.

THE IDEAL WAYS OF OPERATION

Caution

Do not close the room for a long period

of time. Occasionally open the door and

windows to

allow the

entrance of

fresh air.

Warning

Freezing temperature

is bad for health and

a waste of electric

power.

!

I Manual RAS-18G5_3 languages.indb 12 3/3/2011 10:28:28 AM

ENGLISH

– 13 –

FOR USER’S INFORMATION

The Air Conditioner And The Heat Source In The Room

Not Operating For A Long Time

When Lightning Occurs

When the indoor unit is not to be used for a long

period of time, please switch off the power from the

mains. If the power from mains remains “ON”, the

indoor unit still consumes about 8W in the operation

control circuit even if it is in “OFF” mode.

Interference From Electrical Products

Caution

To avoid noise interference, please place the indoor

unit and its remote controller at least 1m away from

electrical products.

Warning

To protect the whole unit during lightning, please

stop operating the unit and remove the plug from

the socket.

Caution

If the amount of heat in the room is above the cooling

capability of the air conditioner (for example: more

people entering the room, using heating equipments

and etc.), the preset room temperature cannot be

achieved.

!

OFF

Inverter-type

ﬂ uorescent

lamp.

To prevent

interference,

place at least

1m away.

TV

I Manual RAS-18G5_3 languages.indb 13 3/3/2011 10:28:28 AM

– 14 –

ATTACHING THE AIR PURIFYING FILTERS

Open the front panel

● Pull up the front panel by holding it at both sides

with both hands.

Remove the pre-ﬁ lter

● Push upward to release the claws and pull out the

ﬁ lter.

Attach the pre-ﬁ lters

● Attach the pre-ﬁ lters by ensuring that the surface

written “FRONT” is facing front.

● After attaching the pre-ﬁ lters, push the front panel at

three arrow portion as shown in ﬁ gure and close it.

Cleaning and maintenance must be carried out when ﬁ lter lamp lights. Before cleaning, stop

operation and switch off the power supply.

CAUTION

!

CAUTION

NOTE

Claws

(4 places)

Attaching the air purifying ﬁ lters

● Attach the air purifying ﬁ lters to the frame by gently

compress its both sides and release after insertion

into pre-ﬁ lter frame.

Do not bend the air purifying

ﬁ lter as it may cause damage

to the structure.

● In case of removing the air purifying ﬁ lters, please follow the above procedures.

● The cooling capacity is slightly weakened and the cooling speed becomes slower when the air

purifying ﬁ lters are used. So, set the fan speed to "HIGH" when using it in this condition.

● Air purifying ﬁ lters are washable and can be use in 1 year time. Type number for this air purifying

ﬁ lter is <SPX-CFH5>. Please use this number for ordering when you want to renew it.

● Do not operate the air conditioner without pre-ﬁ lter. Dust may enter the air conditioner and fault

may occur.

I Manual RAS-18G5_3 languages.indb 14 3/3/2011 10:28:29 AM

ENGLISH

– 15 –

MAINTENANCE

Cleaning and maintenance must be carried out when ﬁ lter lamp lights. Before cleaning, stop

operation and switch off the power supply.

1. PRE-FILTER

Clean the pre-ﬁ lter, as it removes dust inside the room. In case the pre-ﬁ lter is full of dust, the air

ﬂ ow will decrease and the cooling capacity will be reduced. Further, noise may occur. Be sure to

clean the ﬁ lter following the procedure below.

!

CAUTION

Open the front panel and remove the ﬁ lter

● Gently lift and remove the air purifying ﬁ lter

from the ﬁ lter frame.

● Re-insert the air purifying ﬁ lter to the ﬁ lter

frame. Set the pre-ﬁ lter with “FRONT” mark

facing front, and slot them into the original

state.

● After attaching the pre-ﬁ lters, push the front

panel at three arrow portions as shown in

ﬁ gure and close it.

!

CAUTION

● Do not wash with hot water at more than 40°C. The ﬁ lter may shrink.

● When washing it, shake off moisture completely and dry it in the shade; do not expose it directly

to the sun. The ﬁ lter may shrink.

● Do not use detergent on the air purifying ﬁ lter as some detergent may deteriorate the air purifying

ﬁ lter electrostatic performance.

Vacuum dust from the pre-ﬁ lter and air purifying

ﬁ lter using vacuum cleaner. If there is too much

dust, rinse under running tap water and gently

brush it with soft bristle brush. Allow ﬁ lters to

dry in shade.

NOTE:

● Air purifying ﬁ lter should be cleaned every month or sooner if noticeable loading occurs. When

used overtime, it may loose its deodorizing function. For maximum performance, it is recommended

to replace it every 1 year depending on application requirements.

PROCEDURE

I Manual RAS-18G5_3 languages.indb 15 3/3/2011 10:28:31 AM

– 16 –

2. Washable Front Panel

● Remove the front panel and wash with clean

water.

Wash it with a soft sponge.

After using neutral detergent, wash thoroughly

with clean water.

● When front panel is not removed, wipe it with

a soft dry cloth. Wipe the remote controller

thoroughly with a soft dry cloth.

● Wipe the water thoroughly.

If water remains at indicators or signal

receiver of indoor unit, it causes trouble.

Method of removing the front panel.

Be sure to hold the front panel with both

hands to detach and attach it.

!

CAUTION

● Do not splash or direct water to the body of the unit when cleaning it

as this may cause short circuit.

● Never use hot water (above 40°C), benzine, gasoline, acid, thinner or a

brush, because they will damage the plastic surface and the coating.

Removing the Front Panel

● When the front panel is fully opened with

both hands, push the right arm to the inside

to release it, and while closing the front

panel slightly, put it out forward.

Attaching the Front Panel

● Move the projections of the left and right

arms into the Flanges in the unit and

securely insert them into the holes.

3. MAINTENANCE BEFORE LONG OFF PERIOD

● Run the unit by setting the operation mode to

(CIRCULATION), the temperature to 16°C and the fan

speed to HI for about half a day on a ﬁ ne day, and dry

the whole of the unit.

● Switch off the power plug.

Flange

Hole

Projection

Arm

Air

Blow

I Manual RAS-18G5_3 languages.indb 16 3/3/2011 10:28:31 AM

ENGLISH

– 17 –

REGULAR INSPECTION

PLEASE CHECK THE FOLLOWING POINTS BY QUALIFIED SERVICE PERSONNEL EITHER

EVERY HALF YEARLY OR YEARLY. CONTACT YOUR SALES AGENT OR SERVICE SHOP.

1

Is the earth line disconnected or broken?

2

Is the mounting frame seriously affected by rust and is the

outdoor unit tilted or unstable?

3

Is the plug of power line ﬁ rmly plugged into the socket?

(Please ensure no loose contact between them).

Cleaning and maintenance must be carried out only by qualiﬁ ed service personnel. Before cleaning,

stop operation and switch off the power supply.

!

CAUTION

● Please use earth line.

Do not place the earth line near water or gas pipes, lightning-conductor, or the earth

line of telephone. Improper installation of earth line may cause electric shock.

!

● A circuit breaker should be installed depending on the mounting site of the unit. Without a circuit

breaker, the danger of electric shock exists.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow : Earth

Blue : Neutral

Brown : Live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured

markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the plug which

is marked with the letter E or by the earth symbol

or coloured green or green-and-yellow.

The wire which is coloured blue must be connected to the terminal which is marked with the letter

N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter

L or coloured red.

NOTE

If the supply cord is damaged, it must be replaced by the special cord obtainable at authorized

service/parts centers.

Conﬁ rm

I Manual RAS-18G5_3 languages.indb 17 3/3/2011 10:28:32 AM

– 18 –

AFTER SALE SERVICE AND WARRANTY

WHEN ASKING FOR SERVICE, CHECK THE FOLLOWING POINTS

When it does not operate

● Is the fuse all right?

● Is the voltage extremely high or low?

● Is the circuit breaker “ON”?

● Was the air ﬁ lter cleaned?

● Does sunlight fall directly on the outdoor unit?

● Is the air ﬂ ow of the outdoor unit obstructed?

● Are the doors or windows opened, or is there any source

of heat in the room?

● Is the set temperature suitable?

CONDITION CHECK THE FOLLOWING POINTS

Notes

● In quiet or stop operation, the following phenomena may occassionally

occur, but they are not abnormal for the operation.

(1) Slight ﬂ owing noise of refrigerant in the refrigerating cycle.

(2) Slight rubbing noise from the fan casing which is cooled and then

gradually warmed as operation stops.

● The odor will possibly be emitted from the room air conditioner because

the various odor, emitted by smoke, foodstuffs, cosmetics and so on,

sticks to it. So the air ﬁ lter and the evaporator regularly must be cleaned

to reduce the odor.

● Please contact your sales agent immediately if the air conditioner still fails to operate normally after the

above inspections. Inform your agent of the model of your unit, production number, date of installation.

Please also inform him regarding the fault.

● Power supply shall be connected at the rated voltage, otherwise the unit will be broken or could not reach

the speciﬁ ed capacity.

When it does not cool well

Please note:

On switching on the equipment, particularly when the room light is dimmed, a slight brightness ﬂ uctuation

may occur. This is of no consequence.

The conditions of the local Power Supply Companies are to be observed.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualiﬁ ed person in order to avoid a hazard.

NOTE:

I Manual RAS-18G5_3 languages.indb 18 3/3/2011 10:28:33 AM

La page charge ...

Hitachi RAC-24G5 Manuel utilisateur

Ce manuel convient également à

Hitachi RAC-24G5 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents