Porter-Cable PXCMV5248069 Manuel utilisateur

TOPS™ - Thermal Overload Protection System

NOTE: These units DO NOT require a magnetic

starter.

TOPS™ - Dispositif de protection contre la sur-

charge thermique

REMARQUE : Ces compresseurs ne nécessitent

pas l’installation d’un démarreur magnétique

.

TOPS™ - Sistema de protección contra sobre-

cargas térmicas

NOTA: Estas unidades no requieren la

instalación de un arrancador magnético.por

correa

Français : Page 30

Español: Página 60

Instruction manual

Manuel d'instructions

Manual de instrucciones

PXCMV5248069

200-2882_Rev. A_7-12

Belt Drive, Electric Air Compressors

Actionnement pour courroie, Compresseur d’air électrique

Accionamiento por correa, Compresor de aire électrico

2- ENG

TABLE OF CONTENTS

TABLE DES MATIÈRES

INDICE

SAFETY GUIDELINES .................................... 3-6

SPECIFICATION CHART ....................................6

OVERVIEW ..................................................... 6-7

Basic Air Compressor Components ......... 6-7

ASSEMBLY .........................................................7

Assembling the Compressor ........................7

TYPICAL INSTALLATION ................................ 8-9

COMPRESSOR CONTROLS ............................ 10

ELECTRICAL POWER REQUIREMENTS .........11

Electrical Wiring ..........................................11

Main Power Panel .......................................11

Main Power Disconnect Switch .................. 11

Low Voltage Problems ................................11

Grounding Instructions ...............................11

MOTOR RESET SWITCH .................................12

OPERATING INSTRUCTIONS .................... 12-14

Break-in of the Pump ..................................12

Daily Startup ...............................................14

Shutdown....................................................14

MAINTENANCE .......................................... 15-18

Draining the Tank ........................................15

Checking the Oil .........................................15

Changing the Oil .........................................15

Belt Tension ................................................16

Pulley Alignment .........................................17

Cleaning the Air Filter .................................18

Checking the Relief Valve ...........................18

Testing for Leaks ......................................... 18

Storage .......................................................18

SERVICE INTERVAL .........................................18

TROUBLESHOOTING CHART ................... 19-20

PARTS DRAWINGS AND PARTS LISTS ..... 21-25

WARRANTY ................................................ 26-28

GLOSSARY OF TERMS ...................................29

PARTS AND SERVICE ......................................30

CONSIGNES DE SÉCURITÉ .................. 3, 31-33

TABLEAU DES SPÉCIFICATIONS ....................33

VUE D’ENSEMBLE ...........................................34

Éléments de base du compresseur d’air ....34

ASSEMBLAGE..................................................35

Assemblage du compresseur .....................35

INSTALLATION TYPIQUE ........................... 36-37

COMMANDES DU COMPRESSEUR ...............38

SPÉCIFICATIONS DE L’ALIMENTATION

ÉLECTRIQUES ........................................... 38-39

Câblage électrique ...................................... 38

Panneau de tension principale ...................39

Sectionneur de tension principale ..............39

Problèmes de tension trop basse ...............39

Instructions pour la mise à la terre .............39

REMISE EN MARCHE ET CÂBLAGE DU

MOTEUR .........................................................40

MODE D’EMPLOI ....................................... 40-44

Rodage de la pompe ..................................40

Mise en marche quotidienne ......................42

Arrêt ............................................................42

ENTRETIEN ................................................ 43-46

Vidange du réservoir ...................................43

Vérification du niveau d’huile ......................43

Vidange d’huile ...........................................43

Tension de la courroie ................................. 44

Alignement de la poulie ..............................45

Nettoyage du filtre à air ..............................46

Vérification de soupape de décharge .........46

Essai d’étanchéité.......................................46

Entreposage ................................................46

ENTRETIEN PÉRIODIQUE ................................ 46

DÉPANNAGE .............................................. 47-48

DESSIN DES PIÈCES ET LISTEDE PIÈCES ..49-53

GARANTIE .....................................................54-57

GLOSSAIRE DES TERMES ..............................58

PI

È

CES ET RÉPARATIONS ...............................59

PAUTAS DE SEGURIDAD ....................... 3, 60-62

TABLEAU DES SPÉCIFICATIONS ....................62

RESUMEN GENERAL.......................................63

Componentes básicos del compresor

de aire .........................................................63

MONTAJE .........................................................64

Montaje del compresor ...............................64

INSTALACION TIPICA ................................ 65-66

CONTROLES DEL COMPRESOR ....................67

REQUERIMIENTOS DE ALIMENTACIÓN

ELÉCTRICA ......................................................68

Cableado eléctrico ...................................... 68

Panel principal de alimentación .................. 68

Interruptor principal de alimentación ..........68

Problemas causados por bajo voltaje ........68

Instrucciones de puesta a tierra .................68

RESTABLECIMIENTO Y CABLEADO DEL

MOTOR ............................................................69

INSTRUCCIONES OPERATIVAS ................ 69-70

Puesta en marcha inicial de la bomba .. 69-70

Arranque diario ...........................................70

Parada ........................................................70

MANTENIMIENTO ...................................... 72-75

Desagüe del tanque .........................................72

Verificación del nivel de aceite....................72

Cambio de aceite ........................................ 72

Tensión de la correa .................................... 73

Alineación de la polea ................................. 74

Limpieza del filtro de aire ............................75

Revisión de la válvula de alivio ...................75

Detección de fugas ..................................... 75

Almacenamiento .........................................75

INTERVALOS DE SERVICIO .............................75

CUADRO DE DETECCIÓN DE FALLOS ..... 76-77

ESQUEMA DE LA PIEZAS Y LISTA DE LAS

PIEZAS ....................................................... 78-82

GARANTÍA .................................................. 83-85

GLOSARIO DE TERMINOS ..............................86

REPUESTOS Y SERVICIO ................................87

3 - ENG

SAFETY GUIDELINES

The following information relates to protecting YOUR SAFETY and PREVENTING

EQUIPMENT PROBLEMS. To help you recognize this information, we use the

following symbols. Please read the manual and pay attention to these sections.

Indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury.

I DANGER

I WARNING

I CAUTION

CONSIGNES DE SÉCURITÉ

Les informations suivantes concernent VOTRE SÉCURITÉ et LA PROTECTION DU

MATÉRIEL CONTRE LES PANNES. Pour vous aider à identifier la nature de ces

informations, nous utilisons les symboles suivants. Veuillez lire le manuel et prêter

attention à ces sections.

DANGER POTENTIEL POUVANT ENTRAÎNER DE GRAVES

BLESSURES OU LA MORT.

DANGER POUVANT CAUSER DES BLESSURES

GRAVES VOIRE MORTELLES.

DANGER POUVANT CAUSER DES BLESSURES

MOYENNEMENT GRAVES OU L’ENDOMMAGEMENT

DE L’APPAREIL.

I DANGER

I AVERTISSEMENT

I ATTENTION

PAUTAS DE SEGURIDAD

La información que sigue se refiere a la protección de SU SEGURIDAD y la

PREVENCIÓN DE PROBLEMAS DEL EQUIPO. Como ayuda para reconocer esta

información, usamos los siguientes símbolos. Lea por favor el manual y preste

atención a estas secciones.

UN POSIBLE RIESGO QUE CAUSARÁ LESIONES GRAVES

O LA PÉRDIDA DE LA VIDA.

UN RIESGO POTENCIAL QUE PODRÍA PROVOCAR

GRAVES LESIONES O MUERTE.

UN RIESGO POTENCIAL QUE PODRIA PROVOCAR

LESIONES LEVES O DA—AR EL EQUIPO.

I PELIGRO

I ADVERTENCIA

I PRECAUCION

4- ENG

1. RISK OF FIRE OR

EXPLOSION. Never

spray flammable

liquids in a confined

area. It is normal for the motor and

pressure switch to produce sparks while

operating. If sparks come into contact with

vapors from gasoline or other solvents,

they may ignite, causing fire or explosion.

Always operate the compressor in a well–

ventilated area. Do not smoke while

spraying. Do not spray where sparks or

flame are present. Keep compressor as far

from spray area as possible.

2. RISK OF BURSTING. Do not

weld, drill or modify the air tank

of this compressor. Welding or

modifications on the air

compressor tank can severely

impair tank strength and cause an

extremely hazardous condition. Welding or

modifying the tank in any manner will void

the warranty.

3. RISK OF ELECTRICAL

SHOCK. Never use an electric

air compressor outdoors when

it is raining or on a wet surface,

as it may cause an electric

shock.

4. RISK OF INJURY. This unit

starts automatically. ALWAYS

shut off the main power

disconnect, and bleed all

pressure from the system before

servicing the compressor, and when the

compressor is not in use. Do not use the

unit with the shrouds or belt guard

removed. Serious injury could occur from

contact with

moving parts.

5. RISK OF BURSTING. Check

the manufacturer’s maximum

pressure rating for air tools and

accessories. Compressor outlet

pressure must be regulated so

as to never exceed the maximum pressure

rating of the tool. Relieve all pressure

through the hose before attaching or

removing accessories.

6. RISK OF BURNS. High

temperatures are generated by

the pump and manifold. To

prevent burns or other injuries, DO NOT

touch the pump, manifold or transfer tube

while the pump is running. Allow them to

cool before handling or servicing. Keep

children away from the compressor at all

times.

7. RISK TO BREATHING. Be

certain to read all labels when

you are spraying paints or toxic

materials, and follow the safety

instructions. Use a respirator mask if there

is a chance of inhaling anything you are

spraying. Read all instructions and be sure

that your respirator mask will protect you.

Never directly inhale the compressed air

produced by a compressor. It is not

suitable for breathing purposes.

8. RISK OF EYE INJURY.

Always wear ANSI Z87.1

approved safety goggles when

using an air compressor. Never point any

nozzle or sprayer toward a person or any

part of the body. Equipment can cause

serious injury if the spray penetrates the

skin.

9. RISK OF BURSTING. Do not

adjust the relief valve for any

reason. Doing so voids all

warranties. The relief valve has

been pre-set at the factory for the

maximum pressure of this unit. Personal

injury and /or property damage may result if

the relief valve is tampered with.

10. RISK OF BURSTING.Do

not use plastic or pvc pipe for

compressed air. Use only

gavanized steel pipe and fittings

for compressed air distribution

lines.

11. RISK OF BURSTING.

Failure to properly drain

condensed water from air tank,

causing rust and thinning of the

steel air tank.

Drain air tank daily

or after each use. If air tank develops a leak,

replace it immediately with a new air tank or

replace the entire compressor.

12. RISK TO HEARING. Always

wear hearing protection when

using an air compressor. Failure

to do so may result in hearing

loss.

WARNING

Read and understand all safety precautions in this manual before operating. Failure to

comply with instructions in this manual could result in personal injury, property damage,

and/or voiding of your warranty. The manufacturer WILL NOT be liable for any damage

because of failure to follow these instructions.

5 - ENG

WARNING

1. Drain the moisture from the tank on a daily basis. A clean, dry tank will help

prevent corrosion.

2. Pull the pressure relief valve ring daily to ensure that the valve is functioning

properly, and to clear the valve of any possible obstructions.

3. To provide proper ventilation for cooling, the compressor must be kept a

minimum of 12 inches (31 cm) from the nearest wall, in a well–ventilated area.

4. To prevent damage to tank and compressor on stationary models, the

tank must be shimmed so the pump base is level within 1/8” to distribute

oil properly. All feet must be supported, shimming where necessary, prior to

attaching to the floor. Fasten all feet to floor. We also recommend the use of

13. The interconnect cord on

this product contains lead, a

chemical known to the State of

California to

cause cancer, and birth defects

or other reproductive harm. Wash hands

after handling.

NOTE: ELECTRICAL WIRING. Refer to

the air compressor’s serial label for the

unit’s voltage and amperage requirements.

Ensure that all wiring is done by a licensed

electrician, in accordance with the National

Electrical code.

RISK OF BURSTING.

Air Tank: On February 26, 2002, the U.S. Consumer Product Safety Commission pub-

lished Release # 02-108 concerning air compressor tank safety:

Air compressor receiver tanks do not have an infinite life. Tank life is dependent upon

several factors, some of which include operating conditions, ambient conditions, proper

installations, field modifications, and the level of maintenance. The exact effect of these

factors on air receiver life is difficult to predict.

If proper maintenance procedures are not followed, internal corrosion to the inner wall of

the air receiver tank can cause the air tank to unexpectedly rupture allowing pressurized

air to suddenly and forcefully escape, posing risk of injury to consumers.

Your compressor air tank must be removed from service by the end of the year shown on

your tank warning label.

The following conditions could lead to a weakening of the air tank, and result in a violent

air tank explosion:

WHAT CAN HAPPEN HOW TO PREVENT IT

• Failuretoproperlydraincondensedwater

from air tank, causing rust and thinning of

the steel air tank.

• Drainairtankdailyoraftereachuse.Ifair

tank develops a leak, replace it immediately

with a new air tank or replace the entire

compressor.

• Modificationsorattemptedrepairstothe

air tank.

• Neverdrillinto,weldormakeany

modifications to the air tank or its

attachments. Never attempt to repair a

damaged or leaking air tank. Replace with a

new air tank.

• Unauthorizedmodificationstothesafety

valve, or any other components which

control air tank pressure.

• Theairtankisdesignedtowithstand

specific operating pressures. Never make

adjustments or parts substitutions to alter the

factory set operating pressures.

DANGER

6- ENG

BASIC AIR COMPRESSOR COMPONENTS

The basic components of the air compressor are the electric motor, Thermal

Overload Protection System (TOPS), pump, and receiver (tank).

The electric motor (see A) powers the pump.

TOPS senses both temperature and current, providing more complete motor

overload protection than a magnetic starter, which senses only current. If

TOPS senses an overload condition, it will automatically shutdown the

compressor. Allow 10-15 minutes for the unit to cool down, then press

the reset button on the motor to restart

the compressor.

The pump (see B) compresses the air

and discharges it into the tank.

The tank (see C) stores the compressed

air.

The pressure switch (see D) shuts down

the motor and relieves air pressure in

the pump and transfer tube when the air

pressure in the tank reaches the kick–out

pressure. As compressed air is used

and the pressure level in the tank drops

to the kick–in pressure, the pressure

switch restarts the motor automatically,

without warning and the pump resumes

compressing air.

The air line outlet (see E). Connect 1/4”

NPT air hose to this outlet.

Fig. 1

NOTE: See pages 8 & 9

for typical installation

of the 80 gallon model.

vibration pads (094-0137) under tank feet.

5. Fasten the compressor down securely if transporting is necessary. Pressure

must be released from the tank before transporting.

6. Protect the air hose from damage and puncture. Inspect them weekly for

weak or worn spots, and replace if necessary.

7. To reduce the risk of electric shock, do not expose to rain. Store indoors.

WARNING

SPECIFICATION CHART

CALIFORNIA PROPOSITION 65 WARNING: This product contains chemicals

known to the State of California to cause cancer, birth defects and/or

reproductive harm.

MODEL NO. RUNNING

H.P.

TANK

CAPACITY

GALLONS

VOLTAGE/

AMPS/

PHASE KICK-IN

PRESSURE KICK-OUT

PRESSURE

PXCMV5248069 5.2 80 (302,8) 240/22/1 145

(9,99 bar)

175

(12,1 bar)

7 - ENG

ASSEMBLING THE COMPRESSOR

1. Unpack the air compressor. Inspect the unit for damage. If the unit has been damaged

in transit, contact the carrier and complete a damage claim. Do this immediately

because there are time limitations to damage claims.

The carton should contain:

• air compressor

• operator and parts manuals

2. Check the compressor’s serial label to ensure that you have received the model

ordered, and that it has the required pressure rating for its intended use.

3. Locate the compressor according to the following guidelines:

Never locate the compressor in an area where there

are fumes from flammable fluids such as paint, solvents, or gasoline.

It is normal for the motor and pressure switch to produce sparks while

operating. If sparks come into contact with flammable fumes, they may

ignite, causing a fire or explosion. Always operate the compressor in a well

ventilated area.

a. For optimum performance, locate the compressor close to the power panel, as

specified in ELECTRICAL POWER REQUIREMENTS, and as close as possible

to the place where the air will be used. This ensures maximum power to the

compressor and maximum air pressure to the tool. If both of these conditions

cannot be met, it is better to locate the compressor close to the power panel,

and use a longer air hose to reach the usage area.

b. The flywheel side of the compressor must be at least 12 inches (31 cm) from any

wall or obstruction, in a clean, well-ventilated area, to ensure sufficient air

flow and cooling.

c. In cold climates, locate the compressors in a heated building when not in use.

This will reduce problems with lubrication, motor starting and freezing of water

condensation.

d. Remove the compressor from the shipping pallet and place it on the floor or a

hard, level surface. The compressor must be level to ensure proper

lubrication of the pump and good drainage of the moisture in the tank.

Risk of injury: The shipping pallet is not designed as a base for

an operating compressor. Operating the compressor while it is on the pallet

will void your warranty.

e. To prevent damage to tank and pump, the tank must be shimmed so the pump

is level within 1/8” per lineal foot maximum to distribute oil properly. Fasten to

floor and NEVER force tank feet to floor without shims when tightening. We also

recommend the use of vibration pads (094-0137) under tank feet (C).

4. Connect an air hose (not included) to

the compressor.

CFig. 2

I WARNING

8- ENG

TYPICAL INSTALLATION

A Air flow

B Feeder line

C Drain leg

D Moisture trap with drain

E Non–lubricated supply line

F 1/4 turn valve

G Bypass

H Air dryer or aftercooler

J Line filter

K Drip tee with drain

L Air/water filter with petcock

M Regulator

N Lubricator

P Quick coupler

R Air hose to tool

T Flexible air line

U Lubricated supply line

I WARNING

I CAUTION

Risk of bursting, resulting in

injury. Never use Plastic pipe for

compressed air.

Risk of property damage. Never use lubricator

for paint spraying or similar applications.

9 - ENG

TYPICAL INSTALLATION

AIR DRYERS AND AFTER COOLERS

An air dryer or aftercooler is installed directly in the air line.

MOISTURE REMOVAL AND AIR FILTRATION

As the air cools, moisture will condense in the lines. This moisture

must be removed before it reaches the tool being used. To remove this

moisture, run the main air line downhill to a moisture trap and drain. Air/

water filters should also be installed in the positions shown.

AIR PRESSURE REGULATION

Install an air regulator in the drop line for each tool, to regulate air

pressure to that tool. Never exceed the maximum pressure rating of the

tool.

AIR LUBRICATION

Install an air lubricator only for those tools requiring lubrication. Do not

use a lubricator for paint spraying or similar applications. The oil will

contaminate the paint and ruin the job.

SHUT–OFF VALVES

Install shut–off valves in each drop line, to isolate the tool and its

accessories for servicing. You can also install a bypass line around an

accessory.

10- ENG

COMPRESSOR CONTROLS

Refer to Fig. 3.

I WARNING For your safety, tank pressure is preset within the

switch and must never be tampered with.

Pressure Switch (see A)

This switch must not be adjusted by the operator; doing so will void the

warranty. The pressure switch controls the level of air pressure in the tank

by automatically starting and stopping the motor, as required to maintain the

factory preset pressure level.

The pressure switch also automatically bleeds pressure from the pump head

when the pump stops. This feature eliminates back pressure in the pump,

ensuring easier starting.

Pressure Relief Valve (see B)

If the pressure switch does not shut down the motor when pressure reaches

the preset level, this valve will pop open automatically to prevent over

pressurization. To operate manually, pull the ring on the valve to relieve air

pressure in the tank.

Tank Pressure Gauge (see C)

This gauge measures the pressure level of the air stored in the tank. It is not

adjustable by the operator, and does not indicate line pressure.

Fig. 3

11 - ENG

ELECTRICAL POWER REQUIREMENTS

I WARNING Risk of electrical shock. Improper electrical grounding

can result in electrical shock. The wiring should be done by a qualified

electrician.

ELECTRICAL WIRING

Refer to the air compressor’s serial label for the unit’s voltage and amperage

requirements. Ensure that all wiring is done by a licensed electrician, in

accordance with the National Electrical Code.

MAIN POWER PANEL

For best performance and reliable starting, the air compressor must be installed

on a dedicated circuit, as close as possible to the electrical power panel.

Provide circuit breaker or fuse protection at your main power panel. Use time

delay fuses on the circuit, because the compressor will momentarily draw

several times its specified amperage when first started.

NOTE: A circuit breaker is recommended. If the air compressor is connected to

a circuit protected by a fuse, use dual element time delay fuses (Buss Fusetron

type “T” only).

MAIN POWER DISCONNECT SWITCH

Install a main power disconnect switch in the line from the panel to the

compressor. The main power disconnect switch must be located near the

compressor, for ease of use and safety. When turned OFF, the main power

disconnect switch shuts off all power to the compressor. When it is turned ON,

the compressor will start and stop automatically, controlled by the pressure

switch.

LOW VOLTAGE PROBLEMS

Low voltage will cause difficult starting or an overload. Low voltage can be caused by

a low supply voltage from the local power company, other equipment running on the

same line, or inadequate wiring. If any other electrical devices are drawing from the

compressor’s circuit, it may fail to start.

Low voltage to the compressor can be caused by a supply wire of insufficient gauge for

the distance between the compressor and the power source. The longer the distance,

the larger the wire gauge (lower the number) must be, to overcome the inherent voltage

loss caused by the wire resistance. Refer to the National Electrical Code to determine

proper wire size for your circuit.

If the wiring is not adequate, the input voltage will drop by 20 to 40 volts at startup. Low

voltage or an overloaded circuit can result in sluggish starting that causes the circuit

breaker to trip, especially in cold conditions.

GROUNDING INSTRUCTIONS

This product must be connected to a grounded, metallic, permanent wiring

system, or an equipment - grounding terminal or lead on the product.

12- ENG

MOTOR RESET SWITCH AND WIRING

I WARNING Ensure that all guards and shrouds are in place before

pressing the reset switch to restart the motor.

TOPS senses both temperature and current, providing more complete motor

overload protection than a magnetic starter, which senses only current. If TOPS

senses an overload condition, it will automatically

shut down the compressor. Allow 10-15 minutes for

the unit to cool down, than press the reset button

on the motor to restart the compressor.

If the motor shuts down because of overload, wait

10–15 minutes so the motor can cool down, then

press (NEVER force) the reset switch (see A) to

restart the motor (see Fig. 5).

Note: On stationary models not supplied with a

power cord, the electrical power must be wired into

the pressure switch by a Licensed Electrician.

OPERATING INSTRUCTIONS

BREAK-IN OF THE PUMP (Fig. 6)

NOTE: The pump is shipped with break–in oil which should be changed after

the first 8 hours of operation.

1. Make sure the power is connected at the power panel.

2. Check the oil level in the pump (see “Checking the Oil” in the maintenance

section).

3. Open the petcock (see F).

I WARNING Escaping air and moisture can propel debris that

may cause eye injury. Wear safety goggles when opening petcock.

4. Turn ON the main power disconnect switch. Turn the pressure switch to the

AUTO position (see D). The motor should start. Allow the compressor to run

for 30 minutes, to break in the internal parts.

NOTE: If the unit does not operate properly, SHUT DOWN IMMEDIATELY, and

contact your nearest Service Center or call the factory’s Customer

Service Department. DO NOT return the unit to the store where it was

purchased.

5. Shut OFF the main power disconnect. Close the petcock (see E). Connect

your air hoseto the tank outlet.

NOTE: As compressed air is used, the pressure switch will restart the motor

automatically to supply more compressed air to the tank.

AFig. 5

13 - ENG

OPEN

CLOSE

F

E

Fig. 6

14- ENG

OPERATING INSTRUCTIONS

DAILY START-UP (Fig. 6)

1. Check the oil level in the pump (see “Checking the Oil” in the maintenance

section).

2. Make sure the main power disconnect switch is shut OFF.

3. Close the tank petcock (see E).

4. Turn ON the main power disconnect switch. Turn the pressure switch to the

AUTO position (see D). The pump will start filling the tank with air. When the

air pressure in the tank reaches the level preset at the factory, the pressure

switch will turn off the electric motor. As air is used and the pressure level in

the tank drops, the pressure switch will start the motor and the pump will

begin refilling the tank.

I WARNING High temperatures are generated by the pump.

To prevent burns or other injuries, DO NOT touch the pump or

transfer tube while the pump is running. Allow it to cool before

handling or servicing. Keep children away from the compressor at

all times.

NOTE: If the unit does not operate properly, SHUT DOWN IMMEDIATELY, and

contact your nearest Service Center or call the factory’s Customer

Service Department. DO NOT return the unit to the store where it was

purchased.

COLD WEATHER STARTING

In cold weather check that the air filter is clean. ALWAYS use synthetic blend,

non-detergent air compressor oil.

Open the petcock (F) (Fig. 6) to depressurize the tank to zero PSI before starting.

If the compressor will not start, relocate it in a warmer location.

SHUTDOWN (Fig. 6)

1. Turn the pressure switch to the OFF position (see C).

2. Shut OFF the main power disconnect switch.

3. Reduce pressure in the tank through the outlet hose. You can also pull the

tank safety valve ring (see G) and keep it open to relieve pressure in the

tank.

I WARNING Escaping air and moisture can propel debris that

may cause eye injury. Wear safety goggles when opening petcock.

4. Open the petcock (see F) to allow moisture to drain from the tank.

15 - ENG

MAINTENANCE

I WARNING To avoid personal injury, always shut off and unplug the

compressor and relieve all air pressure from the system before performing

any service on the air compressor.

Regular maintenance will ensure trouble–free operation. Your electric powered

air compressor represents high–quality engineering and construction; however,

even high–quality machinery requires periodic maintenance. The items listed

below should be inspected on a regular basis

DRAINING THE TANK (Fig. 6)

I WARNING Condensation will accumulate in the tank. To

prevent corrosion of the tank from the inside, this moisture must

be drained at the end of every workday.

I WARNING Be sure to wear protective eyewear. Relieve the

air pressure in the system and open the petcock on the bottom of

the tank to drain.

CHECKING THE OIL

Check the level of oil in the pump with the sight glass. The pump oil level must

be between A and B (See Fig. 7). Do not overfill or underfill.

NOTE: Use synthetic blend, non-detergent air compressor oil.

CHANGING THE OIL

Remove the oil plug (C) (Fig. 7) and drain the oil until it slows to a drip, then

close. Add oil to the pump by first removing the breather plug (E). Add oil until

the level viewed through the sight glass (D) is between FULL (A) and ADD (B).

Never overfill or underfill the pump.

NOTE: The compressor is pre-filled with synthetic oil. Use synthetic blend, non-

detergent air compressor oil.

A = Full

B = Add

C = Oil drain plug

D = Oil level sight glass

E = Oil fill plug

Fig. 7

C

E

D

16- ENG

BELT TENSION AND PULLEY ALIGNMENT

I WARNING To avoid personal injury, always shut off and

unplug the compressor and relieve all air pressure from the system

before performing any service on the air compressor.

NOTE: Drive belt tensioning and pulley alignment are done at the same time.

They are discussed separately for clarity.

ADJUSTING DRIVE BELT TENSION

Proper belt tension and pulley alignment must be maintained for maximum drive

efficiency and belt life. The correct tension exists if a deflection (see A) of 1/2”

(13 mm) occurs by placing 5 lb (2.3 kg) of force (see B) midway between the

motor pulley and the pump flywheel (See Fig. 8). This deflection can be adjusted

by the following procedure. The pulley should be carefully aligned with the

flywheel, and all setscrews should be kept tight.

1. Remove the belt guard.

2. Loosen the motor mounting bolts.

3. Shift the motor to the point where the correct deflection exists.

4. Retighten the motor mounting bolts.

5. Check to ensure that the tension remained correct.

6. Reinstall the belt guard. All moving parts must be guarded.

Fig. 8

MAINTENANCE

17 - ENG

PULLEY ALIGNMENT

To check pulley alignment, remove the belt guard and place a straightedge

(see A) against the pump flywheel (see B) (See Fig. 9). Measure and record the

distance from the straightedge to the edge of the drive belt at point C. Then

measure the distance from the straightedge to the edge of the drive belt again

at points D and E. Both distances should be the same as at point C. If D or E

are different from C, there is a misalignment which must be corrected before

the compressor is run. To correct a pulley misalignment, use the following

procedure.

1. Remove the belt guard.

2. Loosen the motor mounting bolts.

3. Loosen the setscrew on the motor pulley.

4. Align the motor pulley with the pump flywheel (C = D = E).

5. Retighten the motor pulley setscrew.

6. Adjust the proper belt tension.

7. Retighten the motor mounting bolts.

8. Reinstall the belt guard. All moving parts must be guarded.

Fig. 9

MAINTENANCE

18- ENG

MAINTENANCE

SERVICE INTERVAL

CLEANING THE AIR FILTER

A dirty air filter will reduce the compressor’s

performance and life. To avoid any internal

contamination of the pump, the filter should be

cleaned frequently, and replaced on a regular

basis. Felt filters should be cleaned in warm,

soapy water, rinsed, and allowed to air dry before

reinstallation. Paper filters should be replaced

when dirty. Do not allow the filter to become filled

with dirt or paint. If the filter becomes filled with

paint, it should be replaced. Direct exposure to

dirty conditions or painting areas will void your

warranty.

CHECKING THE RELIEF VALVE

Pull the relief valve daily to ensure that it is operating properly and to clear the

valve of any possible obstructions.

TESTING FOR LEAKS

Check that all connections are tight. A small leak in any of the hoses, transfer

tubes, or pipe connections will substantially reduce the performance of your air

compressor. If you suspect a leak, spray a small amount of soapy water around

the area of the suspected leak with a spray bottle. If bubbles appear, repair or

replace the faulty component. Do not overtighten any connections.

STORAGE

Before storing the compressor for a prolonged period, use an air blow gun to

clean all dust and debris from the compressor. Disconnect the power cord and

coil it up. Pull the pressure relief valve to release all pressure from the tank. Drain

all moisture from the tank. Clean the filter element and filter housing; replace the

element if necessary. Drain the oil from the pump crankcase and replace it with

new oil. Cover the entire unit to protect it from moisture and dust.

Perform the following maintenance at the intervals indicated below.

Inspect and clean air filter ......................................................................Weekly

Check pump oil level ...................................................................................Daily

Change pump oil .................................................... Every 200 operating hours

Use synthetic blend, non-detergent air compressor oil.

Operate the pressure relief valves .............................................................Daily

Check belt tension ................................................. Every 250 operating hours

Drain tank .....................................................................................................Daily

Check and tighten all bolts .......................................... .After first 8 hours and

(Do not overtighten) every 500 operating hours

H = Wingnut

I - Metal cover

J = filter element

19 - ENG

TROUBLESHOOTING

Note: Troubleshooting problems may have similar causes and solutions.

PROBLEM POSSIBLE CAUSE SOLUTION

Excessive current

draw trips circuit

breaker of motor reset

switch

Low voltage/motor

overload Check that power

supply is adequate

and that compressor

is on a dedicated

circuit. If compressor is

connected to a circut

protected by a fuse, use

dual element time delay

fuses (Buss Fusetron

type “T” only).

Drive belt too tight Readjust belt tension

Restricted air passages Inspect and replace

transfer tubes or

check valve, as

required.

Compressor stalls Low voltage motor Furnish adequate power.

Bad check valve Replace the check

valve.

Seized pump Contact authorized

service center.

Low discharge

pressure Air leaks Tighten or replace

leaking fittings or

connections. Do not

overtighten.

Leaking valves Contact authorized

service center.

Restricted air intake Clean or replace air filter

element(s).

Blown gaskets Contact authorized

service center.

Worn piston rings or

cylinder Contact authorized

service center.

Compressor pump

knocking Loose engine pulley or

compressor flywheel Retighten pulley

and flywheel. Check

alignment.

Low oil level in pump

crankcase Keep oil at proper level

at all times.

Excess carbon on valves

or top of piston Contact authorized

service center.

20- ENG

PROBLEM POSSIBLE CAUSE SOLUTION

Oil in discharge air Worn piston rings or

cylinder Contact authorized

service center.

Restricted air intake Clean or replace the air

filter element(s).

Oil level too high Reduce to proper level.

Overheating Poor ventilation Relocate compressor to

an area with cool, dry,

well circulated air, at

least 12 in. from nearest

wall.

Dirty cooling surfaces Clean all cooling

surfaces thoroughly.

Restricted air passages Replace transfer tubes

and/or unloader.

Excessive belt wear Pulley out of alignment Realign pulley with

compressor flywheel.

Improper belt tension Readjust.

Pulley wobbles Replace the pulley and

check for a damaged

crankshaft or flywheel.

Compressor

won’t start in cold

temperatures

Too much back pressure

in tank Open petcock when

starting motor.

40W oil in crankcase Use synthetic blend,

non-detergent air

compressor oil.

Compressor too cold Move compressor to a

warmer location.

TROUBLESHOOTING

La page charge ...

Porter-Cable PXCMV5248069 Manuel utilisateur

Porter-Cable PXCMV5248069 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents