VTech SN1127 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur
Go to www.vtechphones.com (US)
to register your product for enhanced warranty
support and latest VTech product news.
Go to phones.vtechcanada.com (Canada) for
latest VTech product news.
SN1127
Amplified Corded
Answering System with
Big Buttons and Display
User’s manual
US CA
Scan the QR code for
support information
Congratulations
on purchasing your new VTech product. Before using this telephone, please read
Important safety instructions.
This quick start guide provides you with basic installation and use instructions. A limited set
of features are described in abbreviated form. Please refer to the online user’s manual for
a full set of installation and operation instructions at www.vtechphones.com or phones.
vtechcanada.com.
Telephones identified with this logo have reduced noise and interference when used with most
T-coil equipped hearing aids and cochlear implants. The TIA-1083 Compliant Logo is a trademark of
the Telecommunications Industry Association. Used under license.
T
Compatible with
Hearing Aid T-Coil
TIA-1083
The ENERGY STAR® program (www.energystar.gov) recognizes and encourages the use of products
that save energy and help protect our environment. We are proud to mark this product with the
ENERGY STAR® label indicating it meets the latest energy efficiency guidelines.
Important safety
instructions
When using your telephone
equipment, basic safety precautions
should always be followed to
reduce
the risk of fire, electric shock and
injury,
including the following:
1. Read and understand all
instructions.
2. Follow all warnings and
instructions marked on the
product.
3. Unplug this product from the
wall outlet before cleaning.
Do not use liquid or aerosol
cleaners. Use a damp cloth
for cleaning.
4. CAUTION: Do not install the
telephone base at a height
above 2 meters.
5. Do not use this product near
water such as near a bath
tub, wash bowl, kitchen sink,
laundry tub or a swimming
pool, or in a wet basement
or shower.
6. Do not place this product on
an unstable table, shelf, stand
or other unstable surfaces.
7. Avoid placing the telephone
system in places with
extreme temperature, direct
sunlight, or other electrical
devices. Protect your
phone from moisture, dust,
corrosive liquids and fumes.
8. Slots and openings in the
back or bottom of the
telephone base and handset
are provided for ventilation.
To protect them from
overheating, these openings
must not be blocked by
placing the product on a soft
surface such as a bed, sofa
or rug. This product should
never be placed near or over
a radiator or heat register.
This product should not be
placed in any area where
proper ventilation is not
provided.
9. This product should be
operated only from the type
of power source indicated
on the marking label. If you
are not sure of the type of
power supply in your home
or office, consult your dealer
or local power company.
10. Do not allow anything to rest
on the power cord. Do not
install this product where the
cord may be walked on.
11. Never push objects of
any kind into this product
through the slots in the
telephone base or handset
because they may touch
dangerous voltage points or
create a short circuit. Never
spill liquid of any kind on the
product.
12. To reduce the risk of electric
shock, do not disassemble
this product, but take it to
an authorized service facility.
Opening or removing parts
of the telephone base or
handset other than specified
access doors may expose
you to dangerous voltages
or other risks. Incorrect
reassembling can cause
electric shock when the
product is subsequently
used.
13. Do not overload wall outlets
and extension cords.
14. Unplug this product from the
wall outlet and refer servicing
to an authorized service
facility under the following
conditions:
When the power supply
cord or plug is damaged
or frayed.
If liquid has been spilled
onto the product.
If the product has been
exposed to rain or water.
If the product does not
operate normally by
following the operating
instructions. Adjust
only those controls that
are covered by the
operation instructions.
Improper adjustment
of other controls may
result in damage and
often requires extensive
work by an authorized
technician to restore
the product to normal
operation.
If the product has
been dropped and the
telephone base and/
or handset has been
damaged.
If the product exhibits
a distinct change in
performance.
15. Avoid using a telephone
(other than cordless) during
an electrical storm. There is a
remote risk of electric shock
from lightning.
16. Do not use the telephone
to report a gas leak in the
vicinity of the leak. Under
certain circumstances, a
spark may be created when
the adapter is plugged into
the power outlet, or when
the handset is replaced in
its cradle. This is a common
event associated with the
closing of any electrical
circuit. The user should not
plug the phone into a power
outlet, and should not put
a charged handset into the
cradle, if the phone is located
in an environment containing
concentrations of flammable
or flame-supporting gases,
unless there is adequate
ventilation. A spark in such
an environment could create
a fire or explosion. Such
environments might include:
medical use of oxygen
without adequate ventilation;
industrial gases (cleaning
solvents; gasoline vapors;
etc.); a leak of natural gas;
etc.
17. Only put the handset of
your telephone next to your
ear when it is in normal talk
mode.
18. The power adapter is
intended to be correctly
oriented in a vertical or floor
mount position. The prongs
are not designed to hold the
plug in place if it is plugged
into a ceiling, under-the-
table or cabinet outlet.
19. For pluggable equipment,
the socket-outlet shall be
installed near the equipment
and shall be easily accessible.
20. Use only the adapter
included with this product.
Incorrect adapter polarity
or voltage can seriously
damage the product.
21. The applied nameplate is
located at the bottom or near
of the product.
SAVE THESE INSTRUCTIONS
For C-UL Compliance only
Measures de sécurité
importantes
Afin de réduire les risques d’incendie,
de blessures corporelles ou
d’électrocution, suivez toujours ces
mesures préventives de base lorsque
vous utilisez votre téléphone :
1. Lisez et comprenez bien
toutes les instructions.
2. Observez toutes les
instructions et mises en
garde inscrites sur l’appareil.
3. branchez ce téléphone
de la prise murale avant de
le nettoyer. N’utilisez pas
de nettoyeurs liquides ni
en aérosol. N’utilisez qu’un
chiffon doux et légèrement
humecté.
4. ATTENTION: Ne pas installer
le socle téléphonique à
une hauteur supérieure à 2
mètres.
5. N’utilisez pas ce produit
près de l’eau, tel que près
d’un bain, d’un lavabo, d’un
évier de cuisine, d’un bac de
lavage ou d’une piscine, ou
dans un sous-sol humide ou
sous la douche.
6. Ne déposez pas ce
téléphone sur un chariot,
support ou table chancelants.
Lappareil pourrait tomber
et être sérieusement
endommagé.
7. Évitez d’installer le système
téléphonique dans les
endroits soumis à une
température extrême, à la
lumière directe du soleil
ou à proximité immédiate
d’autres appareils électriques
ou électroniques. Protégez
votre téléphone contre
les sources d’humidité, la
poussière, les vapeurs et les
liquides corrosifs.
8. Le boîtier de l’appareil
est doté de fentes et
d’ouvertures d’aération
situées à l’arrière ou en
dessous. Afin d’empêcher la
surchauffe, ces ouvertures ne
doivent pas être obstruées
en plaçant l’appareil sur
un lit, divan, tapis ou autre
surface similaires. Ne placez
pas cet appareil à proximité
d’un élément de chauffage
ni d’une plinthe électrique.
De plus, ne l’installez pas
dans une unité murale ou
un cabinet fermé qui ne
possède pas d’aération
adéquate.
9. Ne faites fonctionner cet
appareil quavec le type
d’alimentation indiqué sur
les étiquettes de l’appareil.
Si vous ne connaissez pas
le voltage de votre maison,
consultez votre marchand ou
votre fournisseur d’électricité.
10. Ne déposez rien sur le
cordon d’alimentation.
Installez cet appareil dans
un endroit sécuritaire, là
où personne ne pourra
trébucher sur la ligne
d’alimentation ni le cordon
téléphonique modulaire.
11. N’insérez jamais d’objets
à travers les fentes et
ouvertures de cet appareil,
car ils pourraient toucher
à des points de tension
dangereux ou court-
circuiter des pièces,
ce qui constituerait un
risque d’incendie ou
d’électrocution. N’échappez
pas de liquides dans
l’appareil.
12. Afin de réduire les risques
d’électrocution, ne
démontez pas l’appareil,
mais apportez-le plutôt
à un centre de service
qualifié s’il doit être réparé.
En enlevant le couvercle,
vous vous exposez à des
tensions dangereuses ou
autres dangers similaires.
Un remontage inadéquat
peut être à l’origine d’une
électrocution lors d’une
utilisation ultérieure de
l’appareil. Débranchez
l’appareil avant de procéder
au nettoyage. Utilisez un
chiffon humide et doux.
13. Ne surchargez pas les prises
de courant et les rallonges.
14. Débranchez cet appareil
de la prise de courant et
communiquez avec le
département de service à la
clientèle de VTech dans les
cas suivants :
Lorsque le cordon
d’alimentation est
endommagé ou écorché.
Si du liquide a été échappé
dans l’appareil.
Si l’appareil a été exposé à
une source d’humidité telle
que la pluie ou l’eau.
Si le produit ne fonctionne
pas normalement en
respectant les instructions
de fonctionnement.
Réglez uniquement les
commandes indiquées
dans le les instructions
de fonctionnement. Les
réglages incorrects des autres
commandes pourraient
provoquer un dommage
qui pourrait exiger un travail
exhaustif de la part d’un
technicien autorisé afin de
rétablir le fonctionnement
normal de l’appareil.
Si le produit a été échappé et
que le socle et/ou le combiné
a été endommagé.
Si le produit affiche une
nette diminution de sa
performance.
15. Évitez d’utiliser un téléphone
(autre qu’un sans fil) pendant
un orage. Les éclairs peuvent
être à l’origine d’une
électrocution.
16. N’utilisez pas le téléphone
pour rapporter une fuite de
gaz à proximité de la fuite.
En certaines circonstances,
une flammèche pourrait
être provoquée lorsque
l’adaptateur est branché à
une prise de courant, ou
lorsque le combiné est
déposé sur le socle. Ceci
est un événement commun
associé à la fermeture d’un
circuit électrique. L’utilisateur
ne devrait pas brancher le
téléphone à une prise de
courant, et ne devrait pas
déposer le combiné chargé
sur le socle, si le téléphone
se trouve à proximité d’un
endroit comportant des
concentrations de gaz
inflammables, à moins
que la ventilation soit
adéquate. Une flammèche
dans un tel endroit pourrait
provoquer un incendie
ou une explosion. De tels
environnements peuvent
comprendre: des endroits
où l’on utilise de l’oxygène
médical sans ventilation
adéquate; des gaz industriels
(dissolvants de nettoyage,
des vapeurs d’essence, etc.);
une fuite de gaz naturel, etc.
17. Ne placez que le combi
de votre téléphone près de
votre oreille lorsqu’en mode
de conversation.
18. Ces adaptateurs ont été
conçus pour être orientés en
position verticale ou montés
au sol. Les broches ne sont
pas conçues pour maintenir
l’adaptateur en place si
celui-ci est barnché dans une
prise au plafond ou sous une
table/ armoire.
19. Pour le MATERIEL
RACCORDE PAR PRISE DE
COURANT, le socle de prise
de courant doit etre installe a
proximite du materiel et doit
etre aisement accessible.
20. N’utilisez que les adaptateurs
inclus avec ce produit.
L’utilisation d’un adaptateur
dont la polarité ou la
tension serait inadéquate
risque d’endommager
sérieusement le produit et
mettre votre sécurité en
péril.
21. La plaque signalétique
appliquée est située au bas
ou à proximité du produit.
CONSERVEZ CES INSTRUCTIONS
FCC, ACTA and IC
Regulations
FCC Part 15
NOTE: This equipment has been
tested and found to comply with
the requirements for a Class B
digital device under Part 15 of
the Federal Communications
Commission (FCC) rules. These
requirements are intended to
provide reasonable protection
against harmful interference in a
residential installation.
This equipment generates, uses
and can radiate radio frequency
energy and, if not installed
and used in accordance with
the instructions, may cause
harmful interference to radio
communications. However, there
is no guarantee that interference
will not occur in a particular
installation. If this equipment
does cause harmful interference
to radio or television reception,
which can be determined by
turning the equipment off and
on, the user is encouraged to
try to correct the interference
by one or more of the following
measures:
Reorient or relocate the
receiving antenna.
Increase the separation
between the equipment and
receiver.
Connect the equipment into
an outlet on a circuit different
from that to which the
receiver is connected.
Consult the dealer or an
experienced radio/TV
technician for help.
WARNING: Changes or
modifications to this equipment
not expressly approved by the
party responsible for compliance
could void the user’s authority to
operate the equipment.
This device complies with Part
15 of the FCC rules. Operation
is subject to the following two
conditions: (1) this device may
not cause harmful interference,
and (2) this device must accept
any interference received,
including interference that may
cause undesired operation.
Privacy of communications may
not be ensured when using this
telephone.
This Class B digital apparatus
complies with Canadian
requirement: CAN ICES-3 (B)/
NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with
Part 68 of the FCC rules and with
technical requirements adopted
by the Administrative Council for
Terminal Attachments (ACTA). The
label on the back or bottom of this
equipment contains, among other
things, a product identifier in the
format US:AAAEQ##TXXXX. This
identifier must be provided to
your telephone service provider
upon request.
The plug and jack used to connect
this equipment to premises wiring
and the telephone network must
comply with applicable Part 68
rules and technical requirements
adopted by ACTA.
A compliant telephone cord and
modular plug is provided with
this product. It is designed to
be connected to a compatible
modular jack that is also compliant.
An RJ11 jack should normally be
used for connecting to a single
line. See the installation instructions
in the user’s manual.
The Ringer Equivalence Number
(REN) is used to determine how
many devices you may connect
to your telephone line and still
have them ring when you are
called. The REN for this product
is encoded as the 6th and 7th
characters following the US: in
the product identifier (e.g., if ##
is 03, the REN is 0.3). In most, but
not all areas, the sum of all RENs
should be five (5.0) or less. For
more information, please contact
your telephone service provider.
This equipment must not be used
with Party Lines. If you have specially
wired alarm dialing equipment
connected to your telephone
line, ensure the connection of
this equipment does not disable
your alarm equipment. If you have
questions about what will disable
alarm equipment, consult your
telephone service provider or a
qualified installer.
If this equipment is malfunctioning,
it must be unplugged from the
modular jack until the problem
has been corrected. Replacement
to this telephone equipment can
only be made by the manufacturer
or its authorized agents. For
replacement procedures, follow
the instructions outlined under the
Limited warranty.
If this equipment is causing harm
to the telephone network, the
telephone service provider may
temporarily discontinue your
telephone service. The telephone
service provider is required to
notify you before interrupting
service. If advance notice is not
practical, you will be notified
as soon as possible. You will be
given the opportunity to correct
the problem and the telephone
service provider is required to
inform you of your right to file
a complaint with the FCC. Your
telephone service provider may
make changes in its facilities,
equipment, operation, or
procedures that could affect the
proper functioning of this product.
The telephone service provider
is required to notify you if such
changes are planned.
This product is equipped with a
corded handset, it is hearing aid
compatible.
If this product has memory dialing
locations, you may choose to store
emergency telephone numbers
(e.g., police, fire, medical) in these
locations. If you do store or test
emergency numbers, please:
Remain on the line and briefly
explain the reason for the call
before hanging up.
Perform such activities in off-peak
hours, such as early morning or
late evening.
Industry Canada
This device contains licence-
exempt transmitter(s)/receiver(s)
that comply with Innovation,
Science and Economic
Development Canada’s licence-
exempt RSS(s). Operation is subject
to the following two conditions:
(1) This device may not cause
interference.
(2) This device must accept
any interference, including
interference that may cause
undesired operation of the device.
Privacy of communications may
not be ensured when using this
telephone.
The term ‘’IC:‘’ before the
certification/registration number
only signifies that the Industry
Canada technical specifications
were met.
The Ringer Equivalence Number
(REN) for this terminal equipment is
1.0. The REN indicates the maximum
number of devices allowed to
be connected to a telephone
interface. The termination of
an interface may consist of any
combination of devices subject
only to the requirement that the
sum of the RENs of all the devices
not exceed five.
This product meets the
applicable Innovation, Science
and Economic Development
Canada technical specifications.
Disclaimer and Limitation of
Liability
VTech Communications, Inc.
and its suppliers assume no
responsibility for any damage
or loss resulting from the
use of this user’s manual.
VTech Communications, Inc.
and its suppliers assume no
responsibility for any loss or
claims by third parties that may
arise through the use of this
product.
Company: VTech
Communications, Inc.
Address: 9020 SW Washington
Square Road - Ste 555 Tigard, OR
97223, United States
Phone: 1 (800) 595-9511 in the
U.S. or 1 (800) 267-7377 in Canada
What’s in the box 1
Connect and install 2
Connect the telephone base 2
Line power mode (no AC power) 3
Mount the telephone base (optional) 4
Overview 8
Setup 13
Voice guide to set answering system 13
Photo speed dial 15
Operate 18
Make a call 18
Answer a call / End a call 18
Speakerphone 18
Volume - Speaker / Ringer 19
Booster 20
Temporary ringer slicencing 20
Call waiting 20
Redial 21
Photo/memory speed dial 21
Temporary tone dialing 22
Equalizer 23
Answering system 24
About the built-in answering system 24
New incoming message indicator 25
Message playback 26
Repeat the playing message 26
Play the previous message 26
Delete a message 26
Delete all messages 26
Remote access 27
Set number of rings 28
Product care | Need
help? 29
Limited warranty 31
Technical Specifications 34
1
User’s manual
What’s in the box
2
1. Connect and install
Connect the telephone base
If you subscribe to
digital subscriber
line (DSL) high-
speed Internet
service through
your telephone
line, make sure
you connect a DSL
filter (not included)
to the telephone
wall jack.
Connect and install
3
Line power mode (no AC power)
When there is a power failure, the telephone base uses power from the telephone
line to let you make and answer calls using the corded handset and dialing keys.
Make a call during power failure
1 Lift the corded handset and wait for a dial tone.
2
Dial a telephone number using the dialing keys. Wait to hear each
key tone upon inputting a digit before pressing the next dialing key.
Answer a call during power failure
Lift the corded handset.
Connect and install
4
1. Connect and install
Mount the telephone base (optional)
1
On the rear side of the telephone base, press the tabs of the wall-mount bracket
to release it from the tabletop orientation.
Connect and install
5
2
Flip the wall-mount bracket down and push it into the telephone base until it
clicks into place.
Connect and install
6
1. Connect and install
3
Slide the handset
tab upward.
Rotate it upside
down.
Slide the handset tab back into the
slot.
The protruding edge of the handset tab holds the corded handset in place when
the telephone is mounted on the wall.
Connect and install
7
4
5
Align and mount the bracket to
the telephone wall mount plate.
Connect and install
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47

VTech SN1127 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur

dans d''autres langues