Generac 005993-0 Le manuel du propriétaire

Marque: Generac

Modèle: 005993-0

Taper: Le manuel du propriétaire

GENERAC _

erator'sIVianual

introduction.............................................................1

Safety Rules...........................................................1

SafetySymbolsand Meanings.......................................1

Generalinformation................................................4

KnowYourPowerWasher.........................................................4

ProductSpecifications..............................................................5

Unpacking.................................................................................5

Set-up.....................................................................5

Assembly..................................................................................5

Add EngineOil..........................................................................6

CheckPumpOil........................................................................6

Add Fuel...................................................................................7

ConnectHoseand WaterSupplyto Pump.................................7

How to Use Nozzles..................................................................9

Cleaningand ApplyingDetergent..................................10

PowerWasherRinsing.................................................10

CleaningDetergentSiphoningTube...............................10

Operation..............................................................11

Operation................................................................................11

PowerWasherLocation..........................................................11

ChecklistBeforeStartingEngine..............................................11

How to Start YourPowerWasher............................................11

AutomaticCoolDown System (ThermalRelief).......................13

AdjustabelPressureSetting.....................................................13

How to StopYourPowerWasher.............................................13

Maintenance.........................................................14

MaintenanceRecommendations..............................................14

MaintenanceSchedule............................................................14

EmissionsControl...................................................................14

PowerWasherMaintenance....................................................14

Checkand CleanInletScreen..................................................14

CheckHighPressureHoses....................................................14

CheckDetergentSiphoningTube.............................................14

CheckSprayGun....................................................................15

NozzleMaintenance................................................................15

PumpOilMaintenance............................................................15

EngineMaintenance................................................................15

EngineOil Recommendations..................................................16

CheckingOilLevel........................................................16

AddingEngineOil.........................................................16

ChangingEngineOil.....................................................16

ServiceAir Cleaner.................................................................17

ServiceSparkPlug..................................................................17

InspectMufflerand SparkArrestor..........................................17

After EachUse........................................................................17

WinterStorage........................................................................18

LongTermStorage..................................................................18

ProtectFuelSystem.....................................................18

ChangeOil...................................................................18

Protectingthe Pump.....................................................18

OtherStorageInstructions.......................................................18

Troubleshooting....................................................lg

TroubleshootingGuide.............................................................19

Warranty...............................................................20

MANUALDELPROPIETARIO.............................23

MANUELDEL'OPI_RATEUR...............................47

INTRODUCTION

Thank you for purchasing this power washer manufactured by

GeneracPowerSystems, Inc.This modelis a high performance,

air-cooled, engine-driven power washer that operates between

3000 and 4000 psi dependingon which model you purchased.

Theseunitsfeaturepowerful Generacengines,atriplex pumpwith

ceramic coated pistons, a pressure control valve, an automatic

thermal relief system, a professional grade spray gun with

vibrationisolationfor reducedfatigue,astainlesssteellance,quick

connect nozzles, steel reinforcedhigh pressure rubber hosefor

long life andmaximumflexibility and a detergentsiphoninghose.

Commonsenseandstrictcompliancewiththespecialinstructions

are essentialto preventing accidents. The operatormust read

this manual and thoroughly understand all of the instructions

and warnings before usingthe equipment.If any portion of the

manualis not understood,contact the nearestAuthorizedDealer

for starting, operating and servicing procedures.The owner is

responsiblefor properandsafe useof the equipment.

Thepowerwasher can operatesafely,efficientlyand reliablyonly

if it is properlylocated,operatedandmaintained.Beforeoperating,

servicingor storing:

• Studyall warnings in this manualand on the productcarefully.

• Becomefamiliar with this manualandthe unit beforeuse.

• Referto theAssemblysectionof themanualfor instructionson

final assembly procedures.Followthe instructionscompletely.

Themanufacturercannot anticipateevery possible circumstance

that might involvea hazard.Thewarnings in this manual,and on

tags and decals affixedto the unit are,therefore,not all inclusive.

If usinga procedure,work method or operatingtechniquethat the

manufacturerdoes not specifically recommend,ensurethat it is

safe for others. Also make sure the procedure,work method or

operatingtechnique utilized does not render the power washer

unsafe.

THE INFORMATIONCONTAINEDHEREIN WAS BASED ON

MACHINESIN PRODUCTIONAT THE TIME OF PUBLICATION.

GENERACRESERVESTHERIGHTTOMODIFYTHISMANUALAT

ANYTIME.

Save these instructionsfor future reference. If you loan this

device to someone,ALWAYSloanALL instructionalmaterialsto

theindividualas well.

WHERETOFINDUS

You can contact GeneracCustomerService by phone at 1-888-

436-3722, or on the internet at www.generac.com.Record the

important information of the unit in the following chart for future

referenceand/orserviceinquiries.

ModelNumber

Serial Number

DatePurchased

SAFETYRULES

Throughoutthis publication,and on tags and decals affixedto the

generator,DANGER,WARNING,CAUTIONand NOTEblocks are

usedto alert personnelto special instructionsabout a particular

operation that may be hazardous if performed incorrectly or

carelessly. Observe them carefully. Their definitions are as

follows:

Indicatesa hazardoussituationor action which,if notavoided,

will resultin death or seriousinjury.

Indicatesa hazardoussituationor actionwhich,if notavoided,

couldresultin deathor seriousinjury.

ACAUTION!

Indicatesa hazardoussituationor actionwhich,if notavoided,

couldresultin minoror moderateinjury.

NOTE:

Notescontainadditional informationimportanttoa procedure

and will be found withinthe regulartextbody of thismanual.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliancewith the special

instructionswhile performingtheaction or serviceareessentialto

preventingaccidents.

SAFETYSYMBOLSANDMEAN/NGS

ToxicFumes Kickback ElectricalShock

Slippery Surface Fall Fluid injection

Fire

MovingParts

Explosion Operator's Manual

Flying Objects Hot Surface

,_ DANGER:CarbonmonoxideproducedduringuseCANKiLL

inminutes.NEVERuseindoorsorinothershelteredareas,

EVENiFdoorsandwindowsare open.DrilyuseOUTSIDEand

farawayfromwindows,doorsandvents.

Somechemicalsor detergents may be harmfulif inhaled

oringested,causingsevere nausea,fainting, or poisoning.

• Operatepowerwasher ONLYoutdoors.

• A runningenginegivesoff carbonmonoxide.

• Carbonmonoxideis an odorless,colorless, poisonousgas.

Breathingcarbonmonoxidecan causeheadache,fatigue,

dizziness,vomiting, confusion,seizures,nausea,fainting

or death.If you start experiencingany of thesesymptoms,

IMMEDIATELYmoveto fresh air. Seekmedicalattention.

• Keepexhaustgasfrom enteringa confined areathrough

windows, doors, ventilationintakes,or other openings.Warn any

occupantsinside aboutthe symptoms of carbon monoxideso

they know to moveto fresh air if theybeginto feel ill.

• Theuse of acarbon monoxidedetector insideany occupied

premisesbetweenthe powerwasher andthe occupantis

recommended.

• NEVERstart or run engineindoors or in an enclosedarea,EVEN

IFwindows and doors areopen.

• Use arespiratoror maskwheneverthere is achancethat

harmful gas or vapors may beinhaled.

• Readall instructionswith respiratoror mask soyou arecertain

the respiratoror maskwill providethe necessaryprotection

againstinhalingharmful gasor vapors. Ifyou beginto

experienceany ofthe COsymptoms listedabove,IMMEDIATELY

moveto fresh air.

,_DANGER: spray gun people, or

NEVERaim at

animals,

electrical devices.Serious injuryor deathwill result.

ALWAYSpointspraygunin safedirection, squeezespraygun

trigger to release highpressure,every time you stopengine.

Engagetrigger lockwhen not in use.

• Thehigh pressurestream ofwaterthat this equipment

produces cancut through skin andits underlyingtissues,leadingto serious injury,possibleamputationor death.

Spray guntraps high water pressure,EVENWHENengine

is stoppedandwater is disconnected,which can cause

injury.

• NEVERallow CHILDRENto operatepowerwasheror playnearby.

This is NOTatoy.

• NEVERrepairhigh pressure hose.Replaceit.

• NEVERrepairleaking connectionswith sealantof any kind.

Replaceo-ring or seal.

• NEVERconnecthigh pressurehose to nozzleextension.

• Keephigh pressurehoseconnectedto pump andspraygun

while system is pressurized.

• NEVERsecurespray gunin openposition.

• NEVERleavespraygununattendedwhile machineis running.

• NEVERusea spraygunwhich doesnot havea trigger lockor

triggerguardin placeandin workingorder.

• ALWAYSbe certain spraygun, nozzlesandaccessories are

correctly attached.

,_WARNING: Riskofelectrocution.

'_ Contactwithpowersourcecancauseelectricshockor

burn.

• NEVERspraynearpower source.

,_WARNING: Contactwith muffler area canresult in serious

burns. Exhaustheat/gasescanignitecombustibles,

structuresor damage thefuel tank causinga fire.

• DONOTtouch hot parts andAVOIDhot exhaustgases.

• Allow equipmentto cool beforetouching.

• Keepat leastfive (5) feet (152 cm) of clearanceon all

sidesof powerwasherincluding overhead.

• It is aviolation of CaliforniaPublicResourceCode,Section

4442, to use or operatetheengineon anyforest-covered,

brush-covered,or grass-coveredland unlessthe exhaust

systemis equippedwith asparkarrester,as definedin

Section4442, maintainedin effectiveworking order.Other

statesor federaljurisdictions may havesimilar laws.

Contactthe original equipmentmanufacturer,retailer,or dealerto

obtaina sparkarresterdesignedfor the exhaustsystem installed

onthis engine.

• Replacementparts must bethe sameandinstalledinthe same

position as theoriginalparts.

,_ WARNING:Fueland its vaporsare extremelyflammable and

explosive. Fire or explosion cancausesevere burns or death.

WHENADDINGDRDRAININGFUEL

• Turnpower washerOFFandlet it cool atleasttwo (2)

minutes beforeremovingfuel cap. Loosencap slowly to

relievepressureintank.

• Fill ordrainfuel tankoutdoors.

• DONOToverfill tank. Allow spacefor fuel expansion.

• If fuel spills, wait until it evaporatesbeforestarting

engine.

• Keepfuel awayfrom sparks, openflames,pilot lights, heat, and

other ignitionsources.

• DONOTfighta cigaretteor smoke.

WHENSTARTINGEQUIPMENT

• Ensuresparkplug, muffler,fuel cap, andair cleanerarein place.

• DONOTcrankenginewith spark plug removed.

WHENOPERATINGEQUIPMENT

• DONOTtip engineor equipmentat anglewhich causesfuel to

spill.

• DONOTsprayflammable liquids.

WHENTRANSPORTINGORREPAIRINGEQUIPMENT

• Transport/repairwithfuel tank EMPTYor with fuel shutoff valve

OFF.

• Disconnectsparkplug wire.

WHENSTORINGFUELDREQUIPMENTWITH FUELiN TANK

• Store awayfrom furnaces, stoves,waterheaters,clothes dryers,

or otherappliancesthat havepilot light or other ignition source

becausetheycan ignitefuel vapors.

,_ll WARNING:Useofpowerwashercancreatepuddlesand

slipperysurfaces.Kickbackfromsprayguncancauseyouto

fail.

Useonly on alevelsurface.

The cleaning area should have adequate slopes and

drainageto reducethe possibility of afall dueto slippery

surfaces.

Donot useon elevatedsurfaces wherechanceof kickback

could resultin a seriousfall.

Firmlygrasp spraygun with both handswhen usinghigh

pressure spray to avoid injury when spray gun kicks

back.

,_WARNING: Starter and otherrotatingpartscan

entangle hands,hair,clothing,or accessories.

* NEVERoperatepowerwasherwithoutprotectivehousing

or covers.

* DONOTwearlooseclothing,jewelryoranythingthat

maybecaughtinthestarteror otherrotatingparts.

* Tieuplonghairandremovejewelry.

,_ WARNING:Starter cordkickback(rapid retraction) canresult

in bodilyinjury.Kickbackwill puffhandand arm toward

engine faster than you can let go. Brokenbones,fractures,

bruises,or sprains couldresult.

• NEVERpullstarter cord withoutfirst relievingspraygun

pressure.

• To relievetrappedpressure, pointgun in safe directionand

releasepressureby pulling/actuatingtrigger on spraygun.

• Whenstartingengine, pullcord slowly until resistanceis felt and

then pull rapidlyto avoidkickback.

• After eachstarting attempt,where enginefailsto run, always

pointspray gunin safe direction, andsqueezespray guntrigger

to releasehigh pressure.

• Firmlygrasp spraygunwith both handswhen using high

pressuresprayto avoid injury when spraygun kicks back.

,_ WARNING:Unintentionalsparking canresult in fire or electric

shock.

WHENADJUSTINGORMAKINGREPAIRSTO YOURPOWER

WASHER.

* Disconnectthe sparkplug wire from the sparkplug and

place the wire whereit cannotcontact sparkplug.

_ WHENTESTINGFORENGINESPARK

* Useapprovedsparkplug tester.

* DONOTcheckfor sparkwith spark plug removed.

CALIFORNIAPROPOSITION65 WARNING

Engineexhaustandsome of its constituentsareknown

to the Stateof Californiato causecancer,birth defects

andotherreproductiveharm.

CAUFORNIAPROPOSITION65 WARNING

This productcontainsor emits chemicalsknownto the

Stateof Californiato causecancer,birth defectsand

otherreproductiveharm.

NOTE:

Highpressurespraymay damage fragile itemsincluding

glass.

DO NOTpoint spray gun at glass when using red (0°) MAX

nozzle.

NEVERaimspray gun at people,animals,electricaldevicesor

plants.

NOTE:

Impropertreatmentof powerwashercandamageit and

shortenits life.

* If you havequestionsaboutintendeduse,ask dealeror contact

qualifiedservicecenter.

* NEVERoperateunits with brokenor missing parts, or without

protectivehousingor covers.

* DONOTby-passanysafety deviceon this machine.

* DONOToperatepowerwasher aboveratedpressure.

* DONOTmodify power washerin anyway.

* Beforestartingpowerwasher incold weather,checkallparts of

the equipmentto be sure icehas notformed there.

* NEVERmovemachinebypullingon hoses.Usehandleprovided

on unit.

* Checkfuel system for leaks or signs of deterioration,such as

chafed or spongy hose, looseor missing clamps, or damaged

tank or cap. Correctall defectsbeforeoperatingpowerwasher.

* Thisequipmentisdesignedto be usedwith Generacauthorized

parts ONLY.If equipment is used with parts that DO NOT

comply with minimum specifications, user assumes all risks

and liabilities.

,_ WARNING:Risk of eye injury.Spray cansplashback or

propelobjects.

* Always wearsafetygoggleswhen using this equipmentor

•. in vicinity of where equipmentis in use.

• Beforestarting the power washer,be sureyou are

wearing adequatesafety goggles.

• NEVERsubstitute safetyglassesfor safetygoggles.

KNOWYOURPOWERWASHER

Readthis owner's manualand safety rules beforeoperatingyour

high powerwasher.

If you loanthis deviceto someone,ALWAYSloanALL instructional

documentationto the individualas well. Comparethe illustrations

with your high power washer to familiarize yourself with the

locationsof variouscontrols(Figure1). Savethis manualfor future

reference.Replacementowner's manualscan be printedfrom the

GeneracWebsite.

A = Spray Gun - Controls the application of water onto the

cleaningsurface with triggerdevice.Includesa trigger lock.

B - Lancewith QuickConnect- Allows you to switch between

four differentnozzles.

C - High PressureHose- Connectone end to water pump and

theotherto the spraygun.

D - Recoil Starter - Usefor startingthe engine.

E - Oil Fill- Checkand add engineoil here.

F - Air Filter- Protectsenginebyfiltering dust, and debrisout of

the intakeair.

G - Pump- Developshigh pressure.

H - ThermalReliefValve- Cycle'swaterthroughthepumpwhen

water reaches 125°EWarmwater will dischargefrom pump

ontoground.This preventsinternalpumpdamage.

I - Engine On/OffSwitch - Runthis switch to "ON" beforeusing

therecoil starter.Turntheswitch to "OFF"to stop the engine.

J - PressureControl/UnloaderValve- Controlsthe highpressure

output.

K- HighPressureOutlet - Connectionfor high pressurehose.

L - Water Inlet - Connectionfor GardenHose.

M - FuelTank- Filltank with regularunleadedfuel. Always leave

roomfor fuel expansion.

N - FuelOn/Off Switch - Turnsfuel supply to the engineon and

off.

0 - Choke- Preparesa cold enginefor starting.

P - ThrottleLever- Increasesor decreasesenginespeed.Throttle

shouldbe at maximumtravel whenthe pressurewasher is in

use.

Q - Nozzles- Chemicalinjection,0°, 15°, 25°, 40° (white,yellow,

redand black)forvarious highpressurecleaningapplications.

R - Pull Pin - Pull the ring to unlock the handle.This allows the

handleto be collapsedfor storage.

S - Adjustable Side Handle- Adjustablebyturningcounterclock-

wise to loosen, adjust to comfortable position and tighten

clock-wise. This allowsfor a firm operatinggrip of the spray

gun.

T - OilDrain- Drainengineoil here.

ITEMSNOTSHOWN

IdentificationLabel(near rear of base plate) - Providesmodel

and serial numberof pressurewasher.Pleasehavethese readily

availableif callingfor assistance.

DetergentSiphoningTube/Filter- Useto siphonpressurewasher

safe detergentsintothe low pressurestream.

Figure 1 - Features & Controls

PRODUCTSPECiFiCATiONS

Pressure- (PSI/ BAR) 3000 / 207 3300/ 228 4000 / 276

FlowRate- (GPM/LPM) 2.8/10.6 3.2/12.1 4.0/15.1

WaterSupplyTemperature- (°F/ C°) 100 / 38 Max

HoseLength- (Feet/ Meters) 35 / 10.7 50 / 15.2

Nozzles- NumberperUnit 5

LanceLength(Inches/ cm) 20 / 51 33 / 84 33 / 84

Gun Professional

EngineDisplacement- (Cubic Inch/ cc) 12.9/ 212 18.4/ 302 25.6 / 420

SparkPlugType F7RTCor equivalent

SparkPlugGap- (Inches/ mm) 0.028-0.031 / 0.70-0.80

FuelCapacity- (Quarts/ Liters) 3.2/ 3.0 4.9/ 4.63 6.3 / 6.0

EngineOilCapacity- (Oz/ Liters) 20 / 0.6 37 / 1.1 37 / 1.1

Low OilShutDown System Yes

On/ Off Switch Yes

UNPACKING

1. Removethe parts bag,accessories,andinserts includedwith

powerwasher.

2. Open carton completely by cutting each corner from top to

bottom.

3. Ensureyou haveall includeditemsprior to assembly.

• MainUnit

• HighPressureHose

• SiphonHose& Filter

• SprayGun

• LancewithQuickConnectFitting

• OilBottle

• PartsBag(whichincludesthefollowing):

HoseHookWireformwithScrewsandAllenWrench

Operator'sManual

Owner'sRegistrationCard

BagcontainingColor-codedNozzles

FilterScreen

4. If you are missing any items from your carton, pleasecall

GeneracCustomerService at 1-888-436-3722. Whencalling

for assistance,pleasehavethemodeland serialnumberfrom

thedatatag available.

5. Fill out and send in registrationcard. Write Model number,

Serial number& dateof purchase in the table located in the

"Whereto FindUs"section.

ASSEMBLY

Readthe entireoperator'smanualbeforeyou attemptto assemble,

or if you have any problems with the assembly of your power

washer,pleasecallGeneracCustomerServiceat1-888-436-3722.

When calling for assistance, please have the model and serial

numberfrom thedatatag available.

1. Thehandlemay be foldeddown or locked into position using

theintegratedpull pin.

Figure 2 - Attach Handle

Install hose hook using provided screws and allen wrench

(Figure3).

Figure 3 - Instal/Hose Hook

Figure5 - Siphon TubeLocation

3. Insert color-coded nozzles in spaces provided in handle

(Figure4).

4. Placespraygunand nozzleextensionintospray gunholderas

shown (Figure4).

Figure4 - InsertNozzles

5. Coilhigh pressurehoseand hangon hook.

6. Attachsiphontubeto locationA (Figure5).

ADDENGINEOIL

1. Placepowerwasher on a flat, levelsurface.

2. Clean area around oil fill and remove orange oil fill cap/

dipstick.

3. Usingoilfunnel(optional),slowlypour contentsof providedoil

bottle intooilfill opening.SeeMaintenancesectionfor oil type

recommendation.

NOTE:

Onsomeunitsthere ismore than one oil fill location.Inthese

instancesitis only necessaryto use one of the oil fill points.

4. Check periodicallyuntil the FULL mark is reached. DONOT

OVERFILL.

NOTE:

Any attemptto crankor startthe engine before it hasbeen

properlyservicedwith the recommendoil may resultin engine

failure.

5. Replaceoil fill cap/dipstickand fully tighten.

CHECKPUMPOIL

1. Placepowerwasher on a flat, levelsurface.

2. Cleanarea aroundoil fill and removevented cap/dipstick (B)

(Figure6).

3. Checkto confirm oil level is up to the "Full" mark on the

dipstick. If oil is required,seeMaintenancesection. DONOT

OVERFILL.

4. See the Maintenancesection for additional information on

pumpoil maintenance.

5. Replaceoil fill cap/dipstickand fully tighten.

Figure 6 - Check Pump Oi/ 3. Install fuel cap and let any spilled fuel evaporate before

starting engine.

Figure 7- Adding rue/

ADDFUEL

Fuelmust meetthese requirements:

* Clean,fresh, unleadedgasoline.

* A minimum of 87 octane/87AKI (91 RON).

* Gasolinewith up to 10%ethanol(gasohol)isacceptable.

NOTE:

Avoid powerwasherdamage.FailuretofollowOperator's

Manualfor fuel recommendationsvoidswarranty.

* DONOTuseunapprovedgasolinesuch as E85.

* DONOTmix oil in gasoline.

* DONOTmodify engineto run on alternatefuels.

Toprotectthefuelsystemfrom gelling,mix in afuelstabilizerwhen

addingfuel. SeeStorage.All fuel isnotthesame.If youexperience

starting or performance problems after using fuel, switch to a

differentfuel provideror changebrands.

Fueland itsvaporsare extremely flammable

and explosive. Fire or explosion cancause

severeburns or death.

WHEN ADDING FUEL

* Turnpower washer OFFand let it cool at least two (2) minutes

beforeremovingfuel cap. Loosen capslowly to relievepressurein

tank.

* Fillfuel tank outdoors.

* DONOToverfill tank.Allow spacefor fuel expansion.

* Iffuel spills, waituntil it evaporatesbeforestarting engine.

* Keepfuel awayfrom sparks, open flames, pilot lights, heat, and

other ignitionsources.

* DONOTlight a cigaretteor smoke.

1. Clean area around fuel fill cap, remove cap.

2. Slowly add regular unleaded fuel to fuel tank. Be careful not

to overfill. Fill to bottom of filter screen, this will allow for fuel

expansion (Figure 7).

CONNECTHOSEANDWATERSUPPLYTOPUMP

NOTE:

DONOTrunthe pumpwithoutthewatersupplyconnected

and turnedon. Damage to equipment resultingfrom failure to

follow this instructionwiil voidwarranty.

NOTE:

Removeand discard the shippingcapfrom the pump'swater

inletbefore attachinghose.

1. Runwaterthroughyour gardenhosefor 30 secondsto clean

out anydebris.

2. Before connecting garden hose to water inlet, inspect inlet

screen beforeinstalling (A) (Figure8). The coneshouldface

outward.Cleanscreenif it containsdebrisor haveit replaced

if damaged. DO NOT run power washer if inlet screen is

damaged.

iMPORTANT:DONOTsiphonstandingwater forthe watersupply.

Use ONLYcold water (tessthan IO0°F).Water supply must be

adequateto handle greaterthan 3.8 gallons per minute and no

less than30 psi.

NOTE:

Using a OneWayValve (vacuumbreaker or checkvalve)at

pumpinletcancausepumpor inletconnectordamage.

* ThereMUST be at least ten feet of unrestricted garden hose

between the power washer inlet and any device, such as a

vacuumbreakeror checkvalve.

* Damage to equipment resulting from failure to follow this

instructionwill voidwarranty.

Figure 8 - Inspect Inlet Screen

Attachendof high pressurehoseto baseof spray gun (Figure

11).

Figure 11 - Connect Hose to Spray Gun

Connectthe gardenhose (notto exceed50 feet in length)to

the water inlet(Figure9). Tightenby hand.

Figure 9 - Connect Garden Hose

The highpressurestreamof water thatthis equipment

producescancutthroughskinand itsunderlying

tissues,leadingto seriousinjury,possibleamputation

or death.Spray guntrapshighwater pressure,even

whenengineisstoppedandwateris disconnected,

whichcancauseinjury.

• NEVERconnecthighpressurehosetolance.

• Keephighpressurehoseconnectedtopumpandspraygunwhile

systemispressurized.

• Always be certainspray gun, nozzlesand accessoriesare

correctlyattached.

6. Connect high pressure hose to pump (uncoil hose before

connectingto pumpor spraygun) (Figure12).

Figure 12- ConnectHighPressureHoseto Pump

Riskof eye injury.Spray cansplashbackor propel

..>40 objects.

• Always wear safety goggles when using this equipment or in

vicinity of equipmentin use.

• Before starting the power washer, be sure you are wearing

adequatesafety goggles.

• NEVERsubstitute safety glassesfor safetygoggles.

Connect lance to spray gun (Figure 10). Tighten by hand.

Figure10- Attach Lance

7. Turn ON the water, squeezethe trigger to purge the pump

system of air (Figure13).

,A CAUTION!

,iA The hosecanbe damagedif it comesin contactwith a

hotengineor muffler.

Figure 13- Squeeze Trigger

* TheWHITENOZZLEis usedfor delicaterinse (lowerpressure and

higherflow), for gentlecleaningof cars/trucks, boats, RV's,patio

furniture, lawn equipment,etc. (Figure15).

Figure 15- Low Pressure Nozzle (White)

HOW TOUSENOZZLES

The quick-connect on the nozzle lance allows you to switch

between different nozzles. Nozzles can be changed while the

power washer is running, once the spray gun trigger is locked

in the safety position. The nozzlesvary the pressure and spray

patternas shown.

* Forthe most effectivecleaning, keepthe nozzlefrom 8 to 24

inches (20 to 61 cm) awayfrom the surfacebeing cleaned.

* If you getthe nozzletoo close,especiallyusinga highpressure

nozzle,you may damagethe surfacebeing cleaned.

The highpressurestreamof waterthatthis equipment

producescancutthroughskinand itsunderlying

tissues,leadingto seriousinjury,possibleamputation

or death. Spray gun trapshighwaterpressure,even

whenengine is stoppedand wateris disconnected,

whichcancauseinjury.

* NEVERexchangenozzleswithoutthetriggerlockbeingengagedon

thespraygun.

* DONOTtwistnozzleswhilespraying.

Followthese instructionsto changenozzles:

1. Pull backthe collaron the quick-connect and pullthe current

nozzle off. Store nozzles in the accessory storage holder

(Figure14).

Figure 14- Nozzles

• TheYELLOWNOZZLEis for generalrinsing (mediumpressureand

mediumflow), idealfor most all purposecleaning such as home

siding, brickpatios,wood decks, drivewaysand sidewalks,garage

floors, etc. (Figure16).

Figure 16 - Medium Pressure Nozzle (Yellow)

* The REDNOZZLEis for maximum rinsing (higher pressure and

lowerflow); for stubborn or hardto reachsurface such assecond

story surfaces, paint removal, oil stains, rust removal or other

stubborn substances(tar,gum, grease,wax, etc.) (Figure17).

,&CAUTION!

,l_ Thistip (RedNozzle)candamageworksurfacesif it is

too close,or heldin one positionfor an extendedtime.

Figure17- MaximumPressureNozzle(Red)

2. Selectdesirednozzle:

3. Pull back on the collar, insert the new nozzleand releasethe

collar.Tugon the nozzleto make sureit is securelyin place.

• Use the BLACK NOZZLEwhen applying detergent (Figure 18).

Onlyusepowerwasher safe detergents/soapsto helpbreakdown

stubborn dirt and grime on avarietyof surfaces.

Figure 18- DetergentNozzle(Black)

CLEANINGANDAPPLYINGDETERGENT

,A CAUTION!

,_ Chemicals cancausebodily injury,and/orproperty

damage.

• NEVERusecausticliquidwiththepowerwasher.

• Use ONLYpower washer safe detergents/soaps.Follow all

manufacturersinstructions.

Toapply detergent,follow these steps:

1. Reviewproper useof nozzles.

2. Prepare detergent solution as required by the job into a

containerlocatedwithin the proximityof the siphontube.

3. Make sure the siphoningtube remains fully submergedinto

thedetergent.

NOTE:

Makesurethe filter remainsfully submergedin detergent

while applying detergent.

NOTE:

Contactwith the hotmuffler candamage the detergent

siphoningtube.

• Wheninsertingthesiphonintoadetergentsolutionbottle,routethe

tubesoastokeepitfrominadvertentlycontactingthehotmuffler.

7. Makesurethe blackdetergentnozzleis installed.

NOTE:

Detergentcannotbe applied withthe highpressurenozzles

(Yellow, White,Greenor Red). Only usethe Black nozzlewith

detergent.

8. Confirmthat all set-up instructionshavebeenfollowed.

NOTE:

Youmustattachall the hosesbefore youstartthe engine.

• Startingtheenginewithoutallthehosesconnected,andwithout

thewaterturnedON,willdamagethepump.

• Damageto the equipmentresultingfrom failureto followthese

instructionswillvoidthewarranty.

9. Start enginefollowing instructions How to Start Your Power

Washer.

10. Applydetergentto a dry surface, starting atthe lowerportion

of the areato bewashed andwork upwardusinglong, even,

overlappingstrokes.

11. Allow the detergent to "soak in" for 3-5 minutes before

washing and rinsing. Reapply as needed to prevent the

surfacefrom drying. DONOTallowthe detergentto dry onthe

surface beingcleaned(preventsstreaking).

IMPORTANT:Youmustflush thedetergentsiphoningsystemafter

eachusebyplacingthefilter intoa bucketof cleanwater,then run

the powerwasher in low pressurefor 1-2 minutes.

POWERWASHERRINS/NG

1. Removethe black detergentnozzlefrom the lance.

2. Select and install the desiredhigh pressure nozzlefollowing

theinstructions Howto UseNozzles.

3. Pointthe spray gun in a safedirection andaway from people,

animalsandplants.Squeezethetriggertoflush anyremaining

chemicalsfrom the system.

4. Keepthe spray gun a safe distancefrom the areayou planto

spray.

Kickback from thespray gun cancauseyouto

• Useonlyona levelsurface.

•Donotuseon anelevatedsurfaceto preventthe riskof a

seriousfall.

• Firmlygraspthespraygunwith bothhandswhenusingthehigh

pressurespraytoavoidinjurywhenthespraygunkicksback.

5. Apply a high pressurespray to a small area andthen check

surfacefor damage.If no damageis found, you can assume

it is okay to continuerinsing.

6. Start atthetop oftheareato be rinsed,workingdownwith the

same overlappingstrokes usedfor cleaning.

CLEAN/NGDETERGENTS/PHON/NGTUBE

If you used the detergentsiphoningtube, you must flush it with

cleanwater beforestoppingthe engine.

1. Place the detergent siphoningtube/filter in a bucket full of

cleanwater.

2. Removethe high pressurenozzlefrom the nozzleextension.

3. Select and install the black detergent nozzle following the

instructions Howto UseNozzles.

4. Flushfor 1-2 minutes.

5. Shut the engine off following the instructions How to Stop

PowerWasher,andturn off water supply.

6. ALWAYSpointthe spray gun in a safe direction,squeezethe

spray gun trigger to releaseretained high water pressure.

Engagethetrigger lock when notin use.

IMPORTANT:Sprayguntraps highwater pressure,evenwhenthe

engineis stoppedandwater isdisconnected.

:_ The highpressurestreamof waterthatthis equipment

producescancutthroughskinand itsunderlying

tissues,leadingto seriousinjury,possibleamputation

or death.Spray guntrapshighwaterpressure,even

whenengineis stoppedand wateris disconnected,

whichcancauseinjury.

• Keepthehighpressurehoseconnectedtothepumpandspraygun

whilethesystemis pressurized.

• ALWAYSpointthespraygunin a safedirection,andsqueezethe

sprayguntriggertoreleasehighpressureeverytimeyoustopthe

engine.Engagethetriggerlockwhennotin use.

OPERATION

If youhaveany problemsoperatingyourpowerwasher,pleasecall

Generaccustomer serviceat 1-888-436-3722.

POWERWASHERLOCATION

ClearancesandAir Movement

_ ANGER:Carbonmonoxide producedduringuse CAN

KILLin minutes.NEVERuseindoorsor in other

shelteredareas, EVENIF doorsand windowsare open.

Onlyuse OUTSIDEand far awayfromwindows,doors

andvents.

NOTE:

For moreinformation,reference the CarbonMonoxide

warningsin theSafety Rules section.

Place the power washer outdoors, in an area that wilt not

accumulatedeadly exhaustgas. NEVERplacethe powerwasher

where exhaust gas could accumulate and enter inside, or be

drawn into a potentially occupied building. Ensurethe exhaust

gas is kept away from any windows, doors, ventilation intakes,

or other openingsthat can allow the exhaustgas to collect in a

confined area. Prevailingwinds and air currentsshould be taken

into considerationwhenpositioningthe powerwasher (Figure19).

• OperatethepowerwasheroutdoorsONLY.

• Keepthe exhaustgasfrom enteringa confinedareathrough

windows,doors,ventilationintakes,or otheropenings.

• NEVERstartor run theengineindoors,or in an enclosedarea,

EVENIFwindowsanddoorsareopen.

_1_ Exhaustheat/gasescanignitecombustibles,

structuresor damagethe fuel tankcausinga

fire.

• Keepat least 5 ft. (152 cm) clearanceon all sides of the power

washerincludingoverhead.

Figure19 - Building Clearances

5 Foot Minimum

CHECKLISTBEFORESTARTINGENGINE

1. Be sure to read and understandthe OperatorSafety section

andthe Operationsectionbeforeusingthepower washer.

2. Checkthat oil is at the proper level in the enginecrankcase

andthat fuel hasbeenaddedto thefueltank.

3. Reviewtheunit'sassemblyandensurethefittings areproperly

secured.Also make surethere areno kinks, cuts, or damage

to high pressurehose.

4. Provide a proper water supply at an adequateflow, clear

screensof debris,andconfirmthat thesystemis purgedof air.

5. Confirm that the unit is on secure, level ground and the

surroundingwork areais clear.

HOW TOSTARTYOURPOWERWASHER

NOTE:

DONOTrun the pumpwithoutthe water supplyconnectedand

turnedon. Damageto the equipment resultingfrom failure to

follow theseinstructionswill voidwarranty.

1. Movethefuel valve leverto theONposition (Figure20).

Figure20- Fue/Va/ve

Off

2. Movethechokeleverto the"CLOSE"position(Figure21).

NOTE:

Fora warmengine, be surethechokeleveris inthe "OPEN"

position.

Figure21 - Choke Lever

Open

Move thethrottle control leverto the"HIGH" position, shown

on theengineasa rabbit(Figure22).

Figure 22 - Throttle Centre/

High Low

Turnthe engineswitch to the "ON"position (Figure23).

Figure 23- The ONPosition

IMPORTANT:Beforestarting the powerwasher,be sure you are

wearingadequatesafetygoggles.

Risk of eye injury.Spraycansplashback or propel

'>_0 objects.

Alwayswearsafetygoggleswhenusingthis equipmentor inthe

vicinityofequipmentin use.

Beforestartingthe powerwasher,be sure you are wearing

adequatesafetygoggles.

NEVERsubstitutesafetyglassesforsafetygoggles.

Place foot on footpad or otherwise secure the unit from

movementwhenpullingthe recoil.

Whenstartingthe engine,graspthestartergrip handle(Figure

24) and pull slowly until you feel some resistance.Then pull

rapidlyto start engine.

Starter cordkickback (rapidretraction)canresult in

bodily injury.Kickback will pullhandand arm toward

enginefaster thanyoucanlet go. Brokenbones,

fractures, bruises, or sprainscouldresult.

* NEVERpullthe startercordwithoutfirst relievingthespraygun

pressure.

* Whenstartingtheengine,pullthecordslowlyuntilresistanceis

felt,thenpullrapidlyto avoidkickback.

* Aftereachstartingattempt,whereenginefailstorun,alwayspoint

thesprayguninasafedirectionandsqueezethesprayguntrigger

to releasehighpressure.

Firmlygraspthe spraygun with both handswhenusinghigh

pressurespraytoavoidinjurywhenthespraygunkicksback.

Return the starter grip handle slowly. DO NOTlet the rope

"snap back" againstthe starter.

Figure24 - StartingtheEngine

StarterHandle

Whenthe engine starts, slowly the move choke leverto the

"OPEN" position as the engine warms. If the enginefalters,

move the choke leverto the "CLOSE"position, then to the

"OPEN"position (Figure25).

9. After each starting attempt, where the engine fails to run,

alwayspointthegun in asafe direction,andsqueezethespray

guntriggerto releasehigh pressure.

10. If the enginefails to start after six pulls, movethe chokelever

to the "OPEN"position,and repeatsteps6 through 10.

The highpressurestreamofwaterthatthis equipment

producescancutthroughskinand itsunderlying

tissues,leadingto seriousinjury,possibleamputation

or death.Sprayguntraps highwater pressure,even

whenengineisstoppedandwateris disconnected,

whichcancauseinjury.

, DONOTallowCHILDRENto operatethe powerwasheror play

nearby.

* Keepthehighpressurehoseconnectedtothepumpandspraygun

whilethesystemis pressurized.

* NEVERaimthespraygunatpeople,animalsorelectricaldevices.

Seriousinjurywill result.

* DONOTsecurethespraygunintheopenposition.

* DONOTleavethe spraygun unattendedwhilethe machineis

running.

* NEVERusea spraygunwhich doesnothavea triggerlockor

triggerguardinplaceandinworkingorder.

* Alwaysbe certainthe spray gun,nozzlesand accessoriesare

correctlyattached.

Contact with the muffler area can result in

serious burns, Exhaust heat/gasescanignite

combustibles,structures or damagethe fuel

tank causinga fire,

• DONOTtouch hot parts andAVOIDhot exhaustgases.

• Allow the equipmentto cool beforetouching.

• Keepat leastfive (5)feet (152 cm) of clearanceon allsides ofthe

powerwasher includingoverhead.

• It is a violation of CaliforniaPublic ResourceCode, Section4442,

to useor operatethe engineon anyforest-covered,brush-covered,

or grass-coveredland unlessthe exhaustsystem is equippedwith

asparkarrester,asdefinedin Section4442, maintainedin effective

workingorder.Otherstatesorfederaljurisdictions mayhavesimilar

laws.

• Replacementparts must be the same and installedin the same

positionas the originalparts.

AUTOMATICCOOLDOWNSYSTEM(THERMAL

RELIEF)

If youruntheengineon yourpowerwasherfor 3-5 minuteswithout

pressingthetriggeronthe spraygun,circulatingwater inthe pump

can reachtemperaturesabove125°EThesystemengagesto cool

the pumpby discharging thewarm waterontotheground.

ADJUSTABLEPRESSURESETTING

Yourpressurewasher pumpis equippedwith a featurethat allows

you to adjust the pressure setting. The pump is preset at the

factory to achievethe highest possible pressure.Todecreasethe

pressure,turn the pressurecontrol knob counterclockwiseto the

desiredpressure.Turningthe pressurecontrolknobclockwiseuntil

it stops will set the pressureback to thefactory setting.

HOWTOSTOPYOURPOWERWASHER

1. Releasethe spray guntrigger.

2. Move the throttle control lever on the engine to the "LOW"

(turtle) position (Figure26).

Figure 26 - Throttle Position

High Low

3. Turnthe engineON/OFFswitch to the "OFF"position.

4. ALWAYSpoint the spray gun in a safe direction, and the

squeeze spray gun trigger to release retained high water

pressure.Engagethe triggerlock when not in use.

5. TurnOFFthe watersupply.

iMPORTANT:Thesprayguntraps highwater pressure,evenwhen

theengineis stoppedand thewater is disconnected.

The highpressurestreamofwaterthatthis equipment

producescancutthroughskinand itsunderlying

tissues,leading to seriousinjury,possibleamputation

or death,Sprayguntraps highwater pressure,even

whenengineisstoppedandwateris disconnected,

whichcancauseinjury,

* Keepthe high pressurehoseconnectedtothe pump andspray gun

while thesystem is pressurized.

* ALWAYSpointthe spraygun ina safedirection,squeezethe spray

guntriggerto releasehigh pressureeverytime youstop theengine.

Engagethe trigger lock whennot in use.

MAINTENANCERECOMMENDATIONS

Regularmaintenancewillimprovetheperformanceandextendthelife

ofthepowerwasher.Seeanyqualifieddealerforservice.

Thepowerwasher'swarrantydoesnotcover itemsthat havebeen

subjectedto operatorabuseor negligence.To receivefull value

from the warranty,the operatormust maintainthe power washer

as instructedin this manual,includingproperstorageas detailedin

WinterStorageandLongTermStorage.

NOTE:

Shouldyouhavequestionsaboutreplacingcomponentson your

powerwasher,pleasecall 1-888-436-3722for assistance.

Some adjustmentswill need to be made periodicallyto properly

maintainyourpowerwasher.

All serviceand adjustmentsshould be made at least once each

season.Followtherequirementsinthe MaintenanceSchedulechart.

NOTE:

Oncea yearyoushouldcleanor replacethesparkplug,clean

or replacetheair filter, andcheckthespraygun andnozzle

extensionassemblyfor wear.Anewsparkplugand cleanair filter

assureproperfuel-air mixtureand helpyourenginerunbetter

and lastlonger.

MAINTENANCESCHEDULE

Follow the hourly or calendar intervals, whichever occurs first.

More frequent service is required when operating in adverse

conditions.

Changeengineoil

Check!cleanwaterinletscreen*

Checkhighpressurehose

Checkdetergentsiphoninghose/filter

Checkspraygunandassemblyfor leaks

Cleandebris

Checkengineoil level

Checkpumpoillevel

Check/cleanaircleanerfilter**

Changepumpoil**

Changeengineoil**

Inspectmufflerandsparkarrester

Servicesparkplug

* Cleanif clogged. Replaceif perforated ortorn.

** Service moreoften under dirty or dusty conditions.

EMISSIONSCONTROL

Maintenance,replacement,or repair of the emissions control

devicesand systemsmaybe performedbyany non-roadengine

repair establishment or individual, However, to obtain "no

charge" emissionscontrol service, the work must be performed

by afactory authorizeddealer.Seethe EmissionsWarranty.

POWERWASHERMAINTENANCE

CleanDebris

Daily or beforeuse, cleanaccumulateddebris from the cleaning

system.Keepthelinkage,springand controlsclean.Keepthe area

aroundand behindthe mufflerfreefrom anycombustible debris.

Inspectthe cooling air slots and openingson the power washer.

Theseopeningsmust be kept cleanandunobstructed.

Powerwasher parts should be kept cleanto reducethe risk of

overheatingand ignitionof accumulateddebris.

• Usea dampcloth to wipe exteriorsurfaces clean.

NOTE:

Improper treatmentof the powerwasher candamageit and

shortenitslife.

• DONOTinsert anyobjectsthroughthecooling slots.

• Usea soft bristlebrushto loosencakedon dirt, oil, etc.

• Usea vacuumcleanerto pick up loosedirt anddebris.

CHECKAND CLEANINLETSCREEN

Examinethescreen on thepump's water inlet. Cleanthe screen if

it is clogged,or replacethe screen if damaged.

CHECKHIGHPRESSUREHOSES

Thehigh pressurehosescan developleaksfrom wear,kinking,or

abuse.Inspectthehoses eachtime beforeusingthem. Checkfor

cuts, leaks,abrasionsor bulging of cover,damageor movement

of couplings. If any of these conditions exist, replacethe hose

immediately.

Thehighpressurestreamof waterthatthisequipment

producescancutthroughskinand itsunderlying

tissues,leadingto seriousinjury,possibleamputation

or death.Spray gun trapshighwaterpressure,even

whenengine is stoppedand water isdisconnected,

whichcancauseinjury.

• NEVERrepair high pressurehose.Replaceit.

• Replacement hose rating MUST meet or exceed maximum

pressure ratingof unit.

CHECKDETERGENTSIPHONINGTUBE

Examinethefilter on thedetergenttube andcleanitif clogged.The

tube should fit tightly on the barbedfitting. Examinethe tube for

leaksor tears.Replacethefilter or tube if eitheris damaged.

CHECKSPRAYGUN

Examinethe hoseconnectionto thespray gun andmakesure itis

secure.Testthe trigger by pressingthe trigger, it "springs back"

into placewhenyou releaseit. Replacethe spraygun immediately

if itfails to "springback".

NOZZLEMAINTENANCE

A pulsing sensation felt while squeezingthe spray gun trigger

may becaused by excessivepumppressure.Theprincipalcause

of excessive pump pressure is a nozzle clogged or restricted

with foreign materials,such as dirt, etc. Tocorrect the problem,

immediatelycleanthe nozzlefollowing these instructions:

1. Shutoff the engineandturn off thewater supply.

2. ALWAYSpointthe spray gun in a safe direction,squeezethe

spray guntriggerto releaseretainedhigh water pressure.

The highpressurestreamof waterthatthis equipment

producescancutthroughskinand itsunderlying

tissues,leadingto seriousinjury,possibleamputation

or death.Spray gun trapshighwaterpressure,even

whenengine isstoppedand water isdisconnected,

whichcancauseinjury.

* Keepthehighpressurehoseconnectedtothepumpandspraygun

whilethesystemispressurized.

* ALWAYSpointthespraygunin a safedirection,andsqueezethe

sprayguntriggerto releasehighpressureeverytimeyoustopthe

engine.Engagethetriggerlockwhennotinuse.

3. Removethenozzlefrom theend of nozzleextension.

4. Use asmall paperclipto free anyforeignmaterialcloggingor

restrictingthe nozzle(Figure27).

5. Removethelancefrom the spray gun.

6. Using a garden hose, remove additional debris by back

flushing water through the lance (Figure28) for 30 to 60

seconds.

7. Reinstallthe nozzleintothe lance.

8. Reconnectthe lanceto the spray gun.

9. Make surethe gardenhose is connectedto the pump water

inlet. Checkthat the high pressurehose is connectedto the

spray gun and pump.Turnon thewater.

Figure 27 - Free Foreign Material

Figure28 - BackFlushLance

10. Start the enginefollowing the instructions How to Start Your

PowerWasher.

11. Testthepowerwasher byoperatingit with eachquickconnect

nozzle.

PUMPOILMAINTENANCE

Changepump oil every 50 hours of operation.

1. Cleanareaaroundoil drain plug (A).

2. Removeoil drain plug.Drainoil completely.

3. Installoil drain plug.Do notovertighten.

4. CleanArea aroundoil dipstick (B).

5. Fill pump with SAE 30 non-detergentoil to "Full" mark on

dipstick.

6. Installoil dipstick untilfingertight.

7. Cleanup anyspilledoil.

Figure2g - Drain PumpOil

ENGINEMAINTENANCE

'_f Unintentionalsparkingcanresultin fire or

electric shock.

WHENADJUSTINGORMAKINGREPAIRSTOYOURPOWER

WASHER:

* Disconnectthesparkplugwirefromthesparkplugandplacethe

wirewhereitcannotcontactsparkplug.

WHENTESTINGFORENGINESPARK:

* Useanapprovedsparkplugtester.

* DONOTcheckforsparkwithsparkplugremoved.

ENGINEOiLBECOIVlIVIENDATIONS

Werecommendthe useof high=qualitydetergentoils acceptableif

classifiedfor serviceSF,SG,SH,SJor higher.DONOTusespecial

additives.

Outdoortemperatures determinethe proper oil viscosity for the

engine.Usethe chart to select the best viscosity for the outdoor

temperaturerangeexpected.

, lm| zmm

°F =20 -10 0 10 20 32 40 60 80 100

oc-3'o -2'o -I'o 6 1'o 2'0 3'o 40

Temperature Range of Expected Use

* Below 50°F(10°C) the use of SAE30 will result in hard starting.

** Above 80°F (27°C) the use of 10W30 may cause increased oil consumption.

Checkoil levelmore frequently.

NOTE:

Synthetic oil meetingILSACGF-2,API certificationmark

and API servicesymbolwith "SJ/CFENERGYCONSERVING"

or higher,is an acceptableoil at all temperatures.Use of

syntheticoil doesnotalter requiredoil changeintervals.

NOTE:

Theengineis equipped withan "Oil Alert System". This

systemwill automaticallystopthe engine beforethe oil level

fails below a safe limit.Toavoidtheinconvenienceof an

unexpectedshutdown,alwayscheckthe engine oil levelbefore

startup.

CHECK/NGO/LLEVEL

Theoil levelshouldbe checkedprior to eachuse or at leastevery

8 hoursof operation.Keepthe oil levelmaintained.

1. Makesurethe powerwasher ison a levelsurface.

2. Cleanareaaroundoil fill cap (Figure31).

3. Removeoil fill cap and wipedipstick clean.

4. Insert dipstick intofiller neck butdo notscrew it in.

5. Verifyoil is at properlevelonthe dipstick.

6. Replaceandtighten oil fill cap,fingertight.

ADDINGENG/NEOIL

1. Makesurethe powerwasher ison a levelsurface.

2. Checkthe oil levelasdescribedin CheckingOil Levelsection.

3. If needed,slowly pour oil into the oil fill opening until the

proper levelon thedipstick is reached(Figure31).

4. Verifyoil levelper the CheckingOil Levelsection.

5. Replaceandtightenthe oil fill cap,fingertight.

CHANG/NGENG/NEOIL

If you are usingyour powerwasher underextremelydirty or dusty

conditions,or in extremelyhot weather,changethe oil moreoften.

,_ CAUTION!

,_ Avoid prolongedor repeatedskincontactwith used

motoroil.

* Usedmotoroil hasbeenshownto causeskincancerin certain

laboratoryanimals.

* Thoroughlywashexposedareaswithsoapandwater.

,_ KEEP OUT OF REACH OF CHILDREN,

* Don'tpollute.Conserveresources.Returnusedoil to collection

centers.

Changeoil whilethe engineisstill warm from running asfollows:

1. Makesurethe unitis on a levelsurface.

2. Disconnectthe sparkplug wirefrom the spark plugand place

thewire whereit cannot contactspark plug.

3. Cleanthe area aroundthe oil drain plug (A) (Figure30). The

oil drain plugis locatedatthe baseof theengine,oppositethe

carburetor.

Figure30 - OilDrain Plug

4. Removethe oil fill cap (Figure31).

5. Removethe oil drain plug and drain oil completely into a

suitablecontainer.

6. Reinstallthe oil drainplug andtighten securely.

Figure 31 - Fi// Engine Oil

7. Slowly pour oil (about 20 oz.) into the oil fill openingto the

proper levelon thedipstick. DONOToverfill.

8. Reinstallthe oil fill cap. Fingertighten cap securely.

9. Wipeup anyspilledoil.

10. Properly dispose of oil in an accordance with all local

regulations.

SERVICEAIRCLEANER

Yourenginewill notrun properlyandmay bedamagedif you run it

with a dirty air cleaner.Servicemoreoften if operatingunderdirty

or dustyconditions.

Toservicethe air cleaner,follow these steps:

1. Loosenthe screw andremovecover (Figure32).

2. Carefullyremovethe filter assembly.

3. Removethe foam filter.

4. Tocleanthe cartridge,gentlytap it on a flat surface.

5. Reinstallthe foam filter.

6. Reinstalla cleanor newcartridge assembly.

7. Installthecover andtighten screwsecurely.

Figure 32 - Service the Air Cleaner

Air

Cleaner

Cover

Paper

Filter

Element

Foam

SERVICESPARKPLUG

Changingthe spark plug will help the engineto start easierand

run better.

1. Cleanthe areaaroundthe sparkplug.

2. Removeandinspectthe spark plug (Figure33).

3. Checkthe electrodegapwith a wirefeelergaugeandresetthe

spark plug gap to the recommendedgap, if necessary (see

Specifications).

4. Replacethe spark plug if the electrodesare pitted, burnedor

the porcelainis cracked. Usethe recommendedreplacement

plug.SeeSpecifications.

5. Installthespark plug andtightenfirmly.

Figure 33 - Change the Spark Plug

SPARKPLUG

0.028-0.031

INSPECTMUFFLERANDSPARKARRESTER

Inspect the muffler for cracks, corrosion, or other damage.

Removethespark arrester,if equipped,and inspectit for damage

or carbon blockage.If replacementparts are required,makesure

to useonly originalequipmentreplacementparts.

Contactwith muffler area canresult in serious

burns.Exhaustheat/gasescan ignite

combustibles,structuresor damagefuel tank

causinga fire.

* DONOTtouchhotpartsandAVOIDhotexhaustgases.

* Allowequipmenttocoolbeforetouching.

* Keepatleast5feet(152cm)ofclearanceonallsidesofthepower

washerincludingoverhead.

* It isa violationof CaliforniaPublicResourceCode,Section4442,

to useoroperatetheengineonanyforest-covered,brush-covered,

orgrass-coveredlandunlesstheexhaustsystemisequippedwith

asparkarrester,asdefinedinSection4442,maintainedineffective

workingorder.Otherstatesorfederaljurisdictionsmayhavesimilar

laws.

Contacttheoriginalequipmentmanufacturer,retailer,or dealerto

obtaina sparkarresterdesignedfortheexhaustsysteminstalled

onthisengine.

* Replacementpartsmustbethesameand installedin the same

positionastheoriginalparts.

AFTEREACHUSE

Water should not remain in the unit for long periods of time.

Sedimentsor mineralscandepositon pumpparts andfreezepump

action. Followthese proceduresafter every use:

1. Shut off the engine,turn off the water supply,point the gun

in a safe direction,and squeezethe triggerto relievetrapped

pressure,and letthe enginecool.

The highpressurestreamof waterthatthis equipment

producescancutthroughskinand itsunderlying

tissues,leadingto seriousinjury,possibleamputation

or death.Sprayguntraps highwater pressure,even

whenengineisstoppedandwateris disconnected,

whichcancauseinjury.

* Keepthe high pressurehoseconnectedtothe pump andspray gun

while thesystem is pressurized.

* ALWAYSpointthespraygunin a safedirection,andsqueezethe

sprayguntriggerto releasehighpressureeverytimeyoustopthe

engine.Engagethetriggerlockwhennotin use.

2. Disconnectthe hosesfrom the spray gun and high pressure

outlet on the pump. Drainwater from the hoses,spray gun,

and lance.Use a ragto wipe off the hose.

3. Emptythe pumpof all pumpedliquids. Checkthat the engine

ON/OFFswitch andfuelvalveareintheOFFposition.Thenpull

therecoilhandleaboutsixtimes. This shouldremovemost of

the liquidin the pump.

4. Storethe unit in a clean, dry area.

5. If storing for morethan 30 days,seethe LongTermStorage

section.

Fueland itsvaporsare extremelyflammable

and explosive.Fireor explosioncancause

severeburnsor death.

WHENSTORINGFUELOREQUIPMENTWiTH FUELiN TANK:

* Storeawayfromfurnaces,stoves,waterheaters,clothesdryers,

or otherappliancesthathavea pilotlightor otherignitionsource

becausetheycanignitefuelvapors.

WINTERSTORAGE

NOTE:

Youmustprotectthe unitfrom freezing temperatures.

* Failuretodosowillpermanentlydamagethepumpandrenderthe

unitinoperable.

* Freezedamageisnotcoveredunderthewarranty.

Toprotectthe unitfrom freezingtemperatures:

1. Followsteps 1-3 inthe previoussection, After EachUse.

2. Use a pump saver to treat pump. This minimizes freeze

damageand lubricatesthe pistonsandseals.

3. If a pump saver is not available,connect a 3-foot sectionof

garden hose to the water inlet adapter. Pour RV-antifreeze

(antifreeze without alcohol) into the hose. Pull the recoil

handletwice. Disconnectthe 3-foot hose.

4. Storethe unit in a clean, dry area.

LONGTERM STORAGE

If you do notplanto usethepowerwasherfor morethan 30 days,

you must preparetheengineand pumpfor long term storage.

PROTECTFUELSYSTEM

Fuelcan become stale when stored for over 30 days. Stalefuel

causes acid and gum deposits to form in the fuel system or

on essentialcarburetor parts. To keepthe fuel fresh, use a fuel

stabilizer, available as a liquid additive or a drip concentrate

cartridge.

Thereis no needto drain the gasolinefrom the engineif a fuel

stabilizeris added according to instructions. Runthe enginefor

2 minutesto circulatethe stabilizerthroughout the fuel system.

Theengineandfuel canthen bestored up to 24 months (perfuel

stabilizermanufacturer'sspecifications).

If the gasoline in the engine has not been treated with a fuel

stabilizer,it must be drainedinto an approvedcontainer.Runthe

engineuntil it stops from lack of fuel. Theuse of a fuel stabilizer

in thestoragecontaineris recommendedto maintainfreshness.

CHANGEO/L

Whilethe engineis still warm, drain the oil from crankcase.Refill

with the recommendedgrade.SeeChangingEngineOil in Engine

Maintenance.

PROTECT/NGTHEPUMP

Toprotectthe pumpfrom damagecausedby mineraldepositsor

freezing, use PumpSaver,Model 61350, to treat the pump. This

preventsfreezedamageand lubricatesthe pistonsandseals.

NOTE:

PumpSaveris available as an optional accessory,it is

notincludedwiththepowerwasher.Contactthenearest

authorizedservicecenterto purchasePumpSaver.

NOTE:

YOUMUSTPROTECTYOURUNiTFROMFREEZING

TEMPERATURES.

• Failureto dosowillpermanentlydamagethepumpandrenderthe

unitinoperable.

• Freezedamageis notcoveredunderwarranty.

To use PumpSaver,make sure the power washer is turned off

and disconnectedfrom the water supply.Readandfollow all the

instructionsandwarnings givenon the PumpSavercontainer.

OTHERSTORAGEINSTRUCTIONS

1. DONOTstore fuel from one seasonto anotherunless it has

beentreatedas describedin ProtectFuelSystem.

2. Replacethe fuel containerif it starts to rust. Rustand/ordirt

infuel can causeproblems if it's usedwith this unit.

3. Coverthe unit with a suitable protectivecover that does not

retainmoisture.

Storage coverscanbeflammable.

*DONOTplaceastoragecoveroverahotpowerwasher.

*Lettheequipmentcoolforasufficienttimebeforeplacingthe

coverontheequipment.

Storethe unitin a clean,dry area.

La page est en cours de chargement...

Generac 005993-0 Le manuel du propriétaire

Marque: Generac

Modèle: 005993-0

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Generac 005993-0 Owner's manual
español: Generac 005993-0 El manual del propietario

Generac 005993-0 Le manuel du propriétaire

Generac 005993-0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents