E-Mu Pipeline Manuel utilisateur

PN XXXXXXXXXXXXX Rev.A

PIPEline

TM

User’s Guide

PIPEline

TM

1 2

3

English ....................................... 1

Français .................................... 25

Deutsch ..................................... 49

EMU Contents.fm Page 0 Thursday, March 5, 2009 12:00 PM

English

Congratulations!

Your versatile E-MU PIPEline™ can be configured as a wireless transmitter

or a receiver. Because it is battery-powered, it can also be used as a

portable wireless device! Purchase additional units to enjoy wireless

networking of your audio equipment and musical instruments at home, in

the studio, or on stage. E-MU PIPEline™ supports transmitting up to three

different sources in the same space. While the E-MU PIPEline™ can be used

with an optional 5V DC power supply adapter, using E-MU PIPEline™ with

the internal battery gives greater freedom and movement, especially when

using as a headphone receiver or music instrument transmitter. Read on to

learn how to get started with your new E-MU PIPEline™!

Contents

About Your E-MU PIPEline™ ........................................................ 2

Broadcasting and Paired Modes .................................................. 3

Analog and Digital Modes ............................................................ 4

Setting Up Your E-MU PIPEline™ ................................................ 5

Using Your E-MU PIPEline™ ...................................................... 11

Troubleshooting Wireless Features .......................................... 13

General Specifications ............................................................... 16

Safety Information ...................................................................... 17

Regulatory Information .............................................................. 20

NOTE

The term “transmitter” used throughout this User’s Guide refers

to an E-MU PIPEline™ when it is configured as a transmitter.

Similarly, “receiver” is used when an E-MU PIPEline™ is

configured as a receiver.

EMU Pipeline UG.fm Page 1 Wednesday, March 4, 2009 5:56 PM

2 About Your E-MU PIPEline™

About Your E-MU PIPEline™

4

3

6

5

9

8

7

1

2

PIPEline

TM

PIPEline

TM

DIGITAL OR ANALOG

FLEXI

JAC

KS

CH

R/T

D/A

B/P

1 Power/Mute button

Press and hold to turn on. When

turned on, press to mute or

unmute.

2 Volume buttons

See “Adjusting volume” on page 11.

3E-MU LED

4Power LED

See “Understanding the Power LED”

on page 12.

5 Flexi-Jack (1/8” Stereo

Line Input/Output jack)

6Flexi-Jacks (RCA jacks)

Can be used to input or output either

analog or digital S/PDIF 48 kHz

signals. See “Analog and Digital

Modes” on page 4.

7 Mode DIP switches

See “Configure your E-MU

PIPEline™ units” on page 5.

8Link LED /

Connect button

See “Understanding the Link LED”

on page 12.

9 5V DC In jack

[5V, 1A (1000mA), Tip=Positive]

EMU Pipeline UG.fm Page 2 Wednesday, March 4, 2009 5:56 PM

Broadcasting and Paired Modes 3

Broadcasting and Paired Modes

You need at least two E-MU PIPEline™ units to form a basic transmitter-

receiver group. With more units, you can configure more complex multiple

wireless groups as shown below.

By setting the Mode DIP switches located at the back of the unit, you can

configure it as a transmitter or receiver, and also set it to be used in either

broadcasting or paired mode.

Broadcasting can be used with any number of paired E-MU PIPEline™

receivers. It is usually used in a “one transmitter-to-many receivers” group.

Paired means that one transmitter is linked solely to one dedicated

receiver.

P

I

P

E

l

i

n

e

T

M

P

I

P

E

l

i

n

e

T

M

P

IP

E

l

i

n

e

T

M

P

I

P

E

l

i

n

e

T

M

P

I

P

E

l

i

n

e

T

M

P

I

P

E

l

i

n

e

T

M

P

I

P

E

l

in

e

T

M

P

I

P

E

l

i

n

e

T

M

Broadcasting

Paired

EMU Pipeline UG.fm Page 3 Wednesday, March 4, 2009 5:56 PM

4 Analog and Digital Modes

Analog and Digital Modes

Your E-MU PIPEline™ can be configured to operate in either Analog or

Digital (S/PDIF 48 kHz) mode by setting the Mode DIP switches. Here are

some things to note when using digital mode:

• For a transmitter in digital mode, ensure that the E-MU PIPEline™ is receiving

a 48 kHz external S/PDIF digital stream. Similarly, for an E-MU PIPEline™

configured as a receiver in digital mode, ensure that the attached external

equipment is capable of receiving a coax S/PDIF 48 kHz digital stream.

• S/PDIF 48 kHz digital audio requires a specific 75-ohm coax digital RCA cable.

This cable can be connected to either one of the RCA jacks of the E-MU

PIPEline™.

• The E-MU PIPEline™ only supports the 48 kHz sample rate when in digital

mode.

• The E-MU PIPEline™ has no DTS or Dolby encoding or decoding capabilities,

but it does offer DTS pass-through.

• The E-MU PIPEline™ cannot input or output digital and analog signals

simultaneously. However, a transmitter-receiver pair can have different digital/

analog settings depending on their attached source or destination device.

EMU Pipeline UG.fm Page 4 Wednesday, March 4, 2009 5:56 PM

Setting Up Your E-MU PIPEline™ 5

Setting Up Your E-MU PIPEline™

You may find it easier to configure and pair your E-MU PIPEline™ units at

one location before placing each unit at its final location.

Step 1: Configure your E-MU PIPEline™ units

Set the Mode DIP switches for your transmitter and receiver(s). Refer to the

following table for the appropriate settings. This table can also be found on

the bottom of your E-MU PIPEline™ unit.

For a transmitter-receiver group, set the settings for DIP switches CH, B/P

and D/A. Then set switch R/T to configure the unit as a transmitter or

receiver. A group consists of at least one transmitter and one receiver.

For example, a transmitter to be used for broadcasting, using RF Channel 1,

streaming analog audio from an analog source should be set as follows:

NOTE

Flexi-Jacks will be either inputs or outputs depending on the

E-MU PIPEline™ transmit/receive mode setting. They can also be

either digital or analog depending on the mode setting.

Position CH B/P R/T D/A

+ Ch 1 Paired Transmit Analog without limiter

0 Ch 2 - - Analog with limiter

- Ch 3 Broadcast Receive Digital

(S/PDIF 48 kHz)

DIGITAL OR ANALOG

CH

R/T

D/A

B/P

CH

B/P

R/T

D/A

EMU Pipeline UG.fm Page 5 Wednesday, March 4, 2009 5:56 PM

6 Connect your E-MU PIPEline™ units

Step 2: Connect your E-MU PIPEline™ units

Connecting a unit as a Transmitter

1a

OR

2a

2b

1b

1c

1d

CH

B/P

R/T

D/A

FIEXI

JACKS

1a Electric guitar with active preamp, synthesizer, mixer

or other audio input source

1b Stereo/Mono to RCA cable (Analog connection)

1c Stereo cable

1d RCA 75-ohm digital cable (S/PDIF 48 kHz connection)

2a Optional 5V power supply adapter

2b AC power outlet

EMU Pipeline UG.fm Page 6 Wednesday, March 4, 2009 5:56 PM

Connect your E-MU PIPEline™ units 7

Connecting a unit as a Receiver

NOTE

When E-MU PIPEline™ is set as a receiver, you can engage a

limiter when in analog output mode to minimize the effects of

clipping. Set the D/A switch to the middle position as indicated in

the table found on page 5.

OR

2a

2b

1b

1c

1d

1a

CH

B/P

R/T

D/A

FIEXI

JACKS

1a Powered stereo or 2.1 speakers, headphones or line

level input amplifier

1b Stereo to RCA cable

1c Stereo cable

1d RCA 75-ohm digital cable (S/PDIF 48 kHz connection)

2a Optional 5V power supply adapter

2b AC power outlet

EMU Pipeline UG.fm Page 7 Wednesday, March 4, 2009 5:56 PM

8 Turn on the receiver

Step 3: Turn on the receiver

Press the Connect button at the back of the receiver.

For paired mode, the Link LED flashes as it searches for a transmitter to

pair with.

Step 4: Turn on the transmitter

Next, press the Connect button of the transmitter.

For Broadcasting Mode

When pairing is successful, the receiver should be able to hear audio from

the output device connected to the receiver.

If you are broadcasting to more than one receiver, repeat Steps 3 and 4.

For Paired Mode

The Link LED of the receiver flashes and then lights up green when pairing

with the transmitter is successful.

Repeat Steps 1 to 4 to pair another dedicated transmitter-receiver group.

This group must use a different RF channel.

5V DC

LINK /

CONNECT

5V DC

LINK /

CONNECT

PIPEline

TM

EMU Pipeline UG.fm Page 8 Wednesday, March 4, 2009 5:56 PM

Position your E-MU PIPEline™ units 9

Once your transmitter and receiver have been paired, they will be linked

automatically when turned on subsequently.

Step 5: Position your E-MU PIPEline™ units

Place the receiver up to 15 meters (approximately 49 feet) away from the

transmitter. You may place the units in different rooms but avoid placing

them near large metal surfaces and objects, or objects emitting radio

frequencies, for example, a radio, cordless phone or other Wi-Fi

®

access

points.

IMPORTANT

DO NOT press the Connect button repeatedly on your transmitter

or receiver before a pairing process is complete or else the units

may not be paired properly.

NOTE

• If your transmitter and receiver do not pair, simply reset them.

To reset the wireless connection, press and hold the receiver’s

Connect button for five seconds.

• For troubleshooting information, see “Troubleshooting Wireless

Features” on page 13.

NOTE

• Signal quality between the transmitter and receiver may be

affected by any object or structure (for example, multiple walls)

that is between the units. Experiment with different positions if

necessary.

• Once the battery is charged, the units can be moved around and

need not be placed near a power outlet. This is the case if it is

connected to portable equipment like headphones or

notebooks. However, movement will be restricted if the

attached equipment (like an amplifier) requires a power outlet.

EMU Pipeline UG.fm Page 9 Wednesday, March 4, 2009 5:56 PM

10 Play and stream music into the transmitter

Step 6: Play and stream music into the transmitter

Play music into your transmitter and broadcast music to your receiver.

PIPEline

T

M

PIPEline

T

M

EMU Pipeline UG.fm Page 10 Wednesday, March 4, 2009 5:56 PM

Using Your E-MU PIPEline™ 11

Using Your E-MU PIPEline™

Adjusting volume

When E-MU PIPEline™ is configured as a transmitter, the volume buttons

on the transmitter function as attenuation buttons. To decrease the volume

of the audio being streamed to the receiver, press the “+” button to increase

attenuation and thus reducing the volume of the audio being streamed.

The volume buttons function as normal for E-MU PIPEline™ receivers.

Charging your E-MU PIPEline™

The E-MU PIPEline™ uses a 1200mAh Li-ion rechargeable battery. When

the battery power is low, the Power LED flashes red and white alternately.

When the battery is charging and the unit is not powered on, the Power LED

lights up red. When the battery is fully charged, the Power LED is not lit.

There is no “low-battery” indication when the external power supply

adapter is being used. A depleted battery takes up to three hours to become

fully charged. When fully charged, it can operate for approximately five to

eight hours without being connected to the power adapter.

Returning to factory default settings

To return E-MU PIPEline™ to factory default settings, press and hold the

Connect button on the rear of the unit for five seconds. The E-MU LED

flashes for two seconds before lighting up again.

Returning to factory default settings will do the following:

• Revert to the original volume setting,

• “Unpair” a receiver.

EMU Pipeline UG.fm Page 11 Wednesday, March 4, 2009 5:56 PM

12 Using Your E-MU PIPEline™

Understanding the Power LED

Understanding the E-MU LED

Understanding the Link LED

* Only applicable to Paired mode. For Broadcasting, LED will not flash.

LED Behavior Status

White Stable Paired and ready for use

Continuous slow flashing Not detecting any signal or signal

is weak

Red Stable Charging

Continuous slow flashing Muted

Red-White Alternate flashing Battery low

Not lit - Fully charged

LED Behavior Status

Blue Two seconds of continuous rapid

flashing

Wireless reset

LED Behavior Status

Green Stable Paired and ready for use

Flashing* Pairing in progress

Rapid flashing One or more Mode DIP switches

are ambiguously positioned

Not lit – Connection lost

EMU Pipeline UG.fm Page 12 Wednesday, March 4, 2009 5:56 PM

Troubleshooting Wireless Features 13

Troubleshooting Wireless Features

There is no sound from my receiver.

Check that:

• The signal source is working properly. If your transmitter is set to digital

mode, ensure that the source is set to stream 48 kHz S/PDIF.

• The transmitter is connected to the power outlet and turned on, or that it

is sufficiently charged (if you are not using an external power supply).

• The transmitter and receiver’s Mode DIP switches are configured

correctly:

• Both are set to the same RF channel.

• Both are set to the identical mode, either Broadcast of Paired mode.

• Transmitter is set to transmit, and receiver set to receive.

• See “Configure your E-MU PIPEline™ units” on page 5.

• The receiver is connected to the power outlet and turned on, or that it is

sufficiently charged (if you are not using a power outlet).

• The Link LEDs are green, and your units are paired. See “The Link LEDs

do not light up.” below.

• The receiver volume is not muted. Press the Power/Mute button.

• The receiver volume is turned up. Press the Volume Up button.

• The output system is turned on and working properly.

The Link LEDs do not light up.

This indicates that the signal from the transmitter is weak or the receiver

has lost its connection with the transmitter.

Try the following:

• Move your transmitter and receiver closer to each other.

EMU Pipeline UG.fm Page 13 Wednesday, March 4, 2009 5:56 PM

14 Troubleshooting Wireless Features

• Reposition your transmitter or receiver so that there are fewer objects

(for example, multiple walls or large metal structures) between them.

• Make sure your transmitter and receiver are not placed on metal

surfaces.

• Reset the wireless connection. Press and hold the receiver’s Connect

button for five seconds.

• Disconnect the transmitter and receiver from the power source. Then

reconnect them again and reset the wireless connection.

• Check that you have set the Mode DIP switches correctly for your

transceivers. See “Configure your E-MU PIPEline™ units” on page 5.

I need more battery-powered transmit time from my E-MU

Pipeline™ transmitter.

If your battery-powered E-MU PIPEline™ transmitter is running low on

power, simply swap it with your receiver (assuming it is plugged in) and

reverse the R/T DIP switch on each unit. The pairing should remain intact.

I have two transceivers which are configured as transmitters. My

receiver is receiving the incorrect transmission.

Check that you have set the same RF setting for both units in a transmitter-

receiver pair. See “Configure your E-MU PIPEline™ units” on page 5.

EMU Pipeline UG.fm Page 14 Wednesday, March 4, 2009 5:56 PM

Troubleshooting Wireless Features 15

My receiver seems to be picking up extra noise, or there are

intermittent pauses.

The placement of your receiver as well as the signals from other wireless

routers or Bluetooth equipment may affect the quality of the transmission.

Try the following:

• Move your transmitter and receiver closer to each other. For best

performance, place your transmitter and receiver on the same floor.

• Place your transmitter or receiver away from other devices that transmit

wireless signals. The receiver may also pick up noise from nearby power

supply equipment.

• Reposition your transmitter or receiver so that there are fewer objects

(for example, multiple walls or large metal structures) between them.

EMU Pipeline UG.fm Page 15 Wednesday, March 4, 2009 5:56 PM

16 General Specifications

General Specifications

Audio Performance

• Signal-to-Noise Ratio (SNR): 96 dB (typical)

• Latency: 5.5 ms (Paired) / 10 ms (Broadcast)

Connectivity

• 3.5 mm (1/8") Stereo jack - Analog Line Input/Output depending on

mode

• RCA jacks - Analog or S/PDIF 48 kHz Input/Output depending on

mode

Rechargeable Battery

• Battery life: 5 to 8 hours (typical)

• Charge time: 3 hours (typical)

Power Adapter

• Supply Voltage: 5V +/- 5%

• Current: 1 A (1000 mA)

• Power: 5 W (Tip = Positive)

Radio Frequency (RF)

• Operating RF range: 2400 - 2483.5 MHz

• Number of RF channels: 3

• Number of simultaneously operating transmitters: 3

• RF transmitter power output: 16 dBm (typical)

EMU Pipeline UG.fm Page 16 Wednesday, March 4, 2009 5:56 PM

Safety Information 17

Safety Information

Refer to the following information to use your product safely, and to reduce the chance of

electric shock, short-circuiting, damage, fire, hearing impairment or other hazards.

Improper handling may void the warranty for your product. For more information, read the

warranty available with your product.

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do not use this apparatus near water.

• Clean only with dry cloth.

• Do not block any ventilation openings. Install the product in accordance with the

instructions.

• Do not install near heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

• Do not expose your product to temperatures outside the range of 0°C to 40°C

(32°F to 104°F).

• Do not pierce, crush or set fire to your product.

• Keep your product away from strong magnetic objects.

• Do not subject your product to excessive force or impact.

• Do not defeat the purpose of the polarized or grounding-type plug. A polarized

plug has two blades with one wider than the other. A grounding type plug has

two blades and a third grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

• Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

• Only use attachments/accessories specified by the manufacturer.

• Use only with the cart, stand, tripod, bracket or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip-over.

• Unplug this apparatus during lightning storms or when unused for long periods

of time.

• Do not dismantle or attempt to repair your product.

Refer all servicing to authorized and qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed to rain or moisture, does

not operate normally,or has been dropped.

EMU Pipeline UG.fm Page 17 Wednesday, March 4, 2009 5:56 PM

La page est en cours de chargement...

E-Mu Pipeline Manuel utilisateur

E-Mu Pipeline Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents