Axial AXI90074T1 Le manuel du propriétaire

Catégorie
Jouets télécommandés
Taper
Le manuel du propriétaire
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’UTILISATION
MANUALE DI ISTRUZIONI
AXI90074-I001
2
EN
Age Recommendation: Not for children under 14 years. This is not a toy.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the
product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this
Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children
without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon
Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the
manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC.
For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a
high probability of superfi cial injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the
product or property of others.
This model is controlled by a radio signal subject to interference from many sources outside your control. This interference can cause momentary loss of
control, so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury.
Never operate your model with low transmitter batteries.
Always operate your model in open spaces away from full-size vehicles,
traffi c and people.
Never operate the model in the street or in populated areas for any reason.
Carefully follow the directions and warnings for this and any optional
support equipment (chargers, rechargeable battery packs, etc.) you use.
Keep all chemicals, small parts and anything electrical out of the reach
of children.
Never lick or place any portion of the model in your mouth as it could
cause serious injury or even death.
Exercise caution when using tools and sharp instruments.
Take care during maintenance as some parts may have sharp edges.
Immediately after using your model, do NOT touch equipment such as
the motor, electronic speed control and battery, because they generate
high temperatures. You may burn yourself seriously touching them.
Do not put fi ngers or any objects inside rotating and moving parts, as this
may cause damage or serious injury.
Always turn on your transmitter before you turn on the receiver in the
car. Always turn off the receiver before turning your transmitter off.
Keep the wheels of the model off the ground when checking the
operation of the radio equipment.
SAFETY PRECAUTIONS AND WARNINGS
WARNING AGAINST COUNTERFEIT PRODUCTS: Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic
high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and
performance of counterfeit products or products claiming compatibility with DSM
®
or Spektrum technology.
3
EN
Your new Horizon Hobby vehicle has been designed and built with a
combination of waterproof and water-resistant components to allow you to
operate the product in many “wet conditions,” including puddles, creeks,
wet grass, snow and even rain.
While the entire vehicle is highly water-resistant, it is not completely
waterproof and your vehicle should NOT be treated like a submarine. The
various electronic components used in the vehicle, such as the Electronic
Speed Control (ESC), servo(s) and receiver are waterproof, however, most
of the mechanical components are water-resistant and should not be
submerged.
Metal parts, including the bearings, hinge pins, screws and nuts, as well
as the contacts in the electrical cables, will be susceptible to corrosion if
additional maintenance is not performed after running in wet conditions.
To maximize the long-term performance of your vehicle and to keep
the warranty intact, the procedures described in the “Wet Conditions
Maintenance” section below must be performed regularly if you choose
to run in wet conditions. If you are not willing to perform the additional
care and maintenance required, then you should not operate the vehicle in
those conditions.
CAUTION: Failure to exercise caution while using this product
and complying with the following precautions could result in
product malfunction and/or void the warranty.
GENERAL PRECAUTIONS
Read through the wet conditions maintenance procedures and make sure
that you have all the tools you will need to properly maintain your vehicle.
Not all batteries can be used in wet conditions. Consult the battery
manufacturer before use. Caution should be taken when using Li-Po
batteries in wet conditions.
Most transmitters are not water-resistant. Consult your transmitter’s
manual or the manufacturer before operation.
Never operate your transmitter or vehicle where lightning may be present.
Do not operate your vehicle where it could come in contact with salt
water (ocean water or water on salt-covered roads), contaminated or
polluted water. Salt water is very conductive and highly corrosive, so
use caution.
Even minimal water contact can reduce the life of your motor if it
has not been certifi ed as water-resistant or waterproof. If the motor
becomes excessively wet, apply very light throttle until the water is
mostly removed from the motor. Running a wet motor at high speeds may
rapidly damage the motor.
Driving in wet conditions can reduce the life of the motor. The additional
resistance of operating in water causes excess strain. Alter the gear ratio
by using a smaller pinion or larger spur gear. This will increase torque (and
motor life) when running in mud, deeper puddles, or any wet conditions
that will increase the load on the motor for an extended period of time.
WET CONDITIONS MAINTENANCE
Drain any water that has collected in the tires by spinning them at high
speed. With the body removed, place the vehicle upside down and pull full
throttle for a few short bursts until the water has been removed.
CAUTION: Always keep hands, fi ngers, tools and any loose or
hanging objects away from rotating parts when performing the
above drying technique.
Remove the battery pack(s) and dry the contacts. If you have an air
compressor or a can of compressed air, blow out any water that may be
inside the recessed connector housing.
Remove the tires/wheels from the vehicle and gently rinse the mud and
dirt off with a garden hose. Avoid rinsing the bearings and transmission.
NOTICE: Never use a pressure washer to clean your vehicle.
Use an air compressor or a can of compressed air to dry the vehicle and
help remove any water that may have gotten into small crevices or corners.
Spray the bearings, drive train, fasteners and other metal parts with a
water-displacing light oil. Do not spray the motor.
Let the vehicle air dry before you store it. Water (and oil) may continue
to drip for a few hours.
Increase the frequency of disassembly, inspection and lubrication of the
following:
- Front and rear axle hub assembly bearings.
- All transmission cases, gears and differentials.
- Motor—clean with an aerosol motor cleaner and re-oil the bushings
with lightweight motor oil.
WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS
TABLE OF CONTENTS
Water-resistant Vehicle with Waterproof Electronics ..................................... 3
box Contents ............................................................................................................4
Required Equipment ............................................................................................... 4
recommended tools ................................................................................................ 4
Getting started checklist........................................................................................5
Vehicle parts ............................................................................................................ 5
Charge the vehicle battery .................................................................................... 6
Install the transmitter batteries ............................................................................ 6
Transmitter functions .............................................................................................6
Install the vehicle battery ...................................................................................... 7
Binding ......................................................................................................................8
Range-checking the radio system ....................................................................... 8
vehicle maintenance ..............................................................................................9
Adjusting the battery tray .................................................................................... 10
AE-5L Forward/reverse ESC with drag brake ..................................................10
Gear Ratios.............................................................................................................11
Troubleshooting .....................................................................................................11
Notes .......................................................................................................................11
Limited Warranty ...................................................................................................12
Warranty and Service Contact Information .....................................................12
FCC Information ..................................................................................................... 13
IC Information ........................................................................................................13
Compliance Information for the European Union ............................................ 13
Parts reference ..................................................................................................... 50
Exploded views......................................................................................................55
Parts lists ................................................................................................................ 59
Electronics ............................................................................................................. 61
4
EN
BOX CONTENTS
• Parts Bag • Cross Wrench
Battery charger compatible with
the chosen vehicle battery type
(4) AA Alkaline batteries 2-3S LiPo Battery
OR
5-9 Cell NiMH/NiCd battery
(IC3™ Connector Required)
• Hex Drivers
(1.5, 2.0, 2.5mm)
• Hobby
Knife
• Side Cutter • Curved
Scissors
• Long-nose Plier
• Spektrum
STX2
®
2.4GHz Transmitter (SPMSTX200)
Wraith 1.9 RTR
- 35T Electric Motor (AX31312)
- SRX200 2CH Receiver (SPMSRX200)
- TSX45 High-Torque Metal Gear Dual
Ball Bearing Servo (TACM0245)
- AE-5L ESC w/LED Ports and Lights (DYNS2213)
- AE-5L LED Light Set (AX31481)
REQUIRED EQUIPMENT
RECOMMENDED TOOLS
5
EN
Steering Servo
Steering Rack
Steering Knuckle
Battery Tray
Spur/Pinion/Slipper
(Under Cover)
Transmission
Driveshaft
Upper 4-link Bar
Differential
(inside axle housing)
Front Body Mount
Receiver Box
ESC Plug
Electronic Speed Control (ESC)
Motor
Lower 4-link Bar
Shock Absorber
VEHICLE PARTS
GETTING STARTED CHECKLIST
Read the manual
Familiarize yourself with the vehicle and its components
Check all screws, especially the driveshaft setscrews, for tightness
from the factory
Charge the vehicle battery
Install 4 AA batteries in the transmitter
Power on the transmitter
Install the vehicle battery in the vehicle
Check for proper function of the throttle and steering
Range check the radio system
Drive the vehicle, challenge yourself and have FUN!
Perform any necessary vehicle maintenance
6
EN
INSTALL THE TRANSMITTER BATTERIES
TRANSMITTER FUNCTIONS
This transmitter requires 4 AA batteries.
1. Remove the battery cover from the transmitter.
2. Install the batteries as shown.
3. Install the battery cover.
CAUTION: NEVER remove the transmitter batteries while the model
is powered on. Loss of model control, damage, or injury may occur.
CAUTION: If using rechargeable batteries, charge only
rechargeable batteries. Charging non-rechargeable batteries may
cause the batteries to burst, resulting in injury to persons and/or damage
to property.
CAUTION: Risk of explosion if battery is replaced by an incorrect
type. Dispose of used batteries according to national regulations.
A. Servo Reversing
To reverse the Throttle (TH) or Steering (ST) channel, switch the position
of the correlating switch—“N” is for normal, “R” is for reverse.
B. Throttle Trim
Adjusts the throttle neutral point
C. Steering Trim
Adjusts the steering center point. Normally, the steering trim is adjusted
until the vehicle tracks straight.
D. Throttle Rate
Adjusts the end point of the throttle
E. Steering Rate
Adjusts the end point of the steering
F. Indicator Lights
• Solid red lights: Indicates radio connectivity and adequate battery power
Flashing red lights: Indicates the battery voltage is critically low.
Replace batteries
G. Throttle Limit
Limits throttle output to 50/75/100%
Select 50% or 75% for less experienced drivers or when you are driving
the vehicle in a small area.
H. Antenna
I. Power Button
J. Throttle/Brake
K. Steering Wheel
2.4GHZ DIGITAL
RADIO SYSTEM
G
J
I
H
K
A
B
D
F
E
C
Follow the manufacturer’s directions for your charger to properly charge
the vehicle battery.
CAUTION: Only use chargers designed to charge the chosen
battery type. Using an incorrect charger or incorrect charger
settings could cause the battery to catch fi re or explode.
CHARGE THE VEHICLE BATTERY
7
EN
INSTALL THE VEHICLE BATTERY
NOTICE: Power to the vehicle is controlled by connecting and
disconnecting the battery from the ESC. Always power on the transmitter
rst before connecting the vehicle battery. Always disconnect the
battery from the ESC when not in use.
2. Remove the body clips and open the hood.
3. Connect the battery to the ESC. Close the hood and replace the body
clips.
NOTICE: Always disconnect the battery from the
ESC before powering off the transmitter. Loss of
vehicle control may result.
1. Power on the transmitter.
8
EN
BINDING
Bind Port
The radio system should be checked before operating the vehicle to ensure proper operation and adequate range.
1. Turn on the transmitter.
2. Connect the battery in the vehicle.
3. Have a friend hold the vehicle while keeping hands and loose clothing away from moving parts.
4. Walk away until you are at the maximum planned operating distance from the vehicle.
5. Turn the steering wheel side to side and operate the throttle, both forward and reverse, checking for any erratic behavior.
6. If any erratic behavior is exhibited, DO NOT operate the vehicle. Call customer service for assistance.
RANGE-CHECKING THE RADIO SYSTEM
Binding is the process of programming the receiver to recognize the GUID
(Globally Unique Identifi er) code of a single specifi c transmitter. The STX2
®
transmitter and SPMSRX200 receiver are bound at the factory. If you need
to rebind, follow the instructions below.
1. Insert the Bind Plug in the BIND port on the receiver.
2. Connect a fully charged battery pack to the ESC.
3. Power on the ESC. The red LED fl ashes, indicating the receiver is in
bind mode.
4. Center the ST TRIM and TH TRIM dials on the transmitter.
5. Turn the steering wheel to Full Right. Power the transmitter on while
holding the steering wheel to the Right.
6. Release the steering wheel when the receiver LED stops fl ashing.
7. Remove the Bind Plug, then power off the receiver to save the settings.
8. Power off the transmitter.
9. Remove the bind plug and store it in a convenient place.
You must rebind when:
Different failsafe positions are desired e.g., when throttle or steering
reversing has been changed.
Binding the receiver to a different transmitter.
9
EN
Replace any
noticeable bent or
broken parts
Check the wheel nuts
for tightness
If applicable, check
the slipper clutch for
proper operation
Check for wear on
the ball joints in
the steering and
suspension links
(replace if necessary)
Ensure the wheel
beads are still fi rmly
bonded around the
entire circumference
of the rim
Check the receiver
antenna for damage
Check driveshaft
set screws and
apply thread
locking compound if
necessary
Keep the chassis free
of dirt and debris
Check the steering
operation for any
binding
Inspect shock
absorbers for smooth
dampened operation
Check for loose
screws on the chassis,
especially the knuckle,
C-hub and axle lockout
screws
Inspect the spur
and pinion gears for
damage
Check for any loose
connections or frayed
wiring
Check the driveline
for smooth, bind free
operation
Replace the
transmitter batteries
when indicated by
the transmitter, as
described in the
Transmitter Functions
section
Just like a full size car or truck your RC vehicle must undergo periodic maintenance in order to ensure peak performance. Preventative maintenance will
also help avoid needless breakages which could result in costly repairs. Below are some suggestions to properly maintain your vehicle.
VEHICLE MAINTENANCE
10
EN
M3x8mm (x4)
Battery ESC
Red
Black
Motor
ADJUSTING THE BATTERY TRAY
AE-5L FORWARD/REVERSE ESC WITH DRAG BRAKE
To Receiver
Throttle Channel
SETUP
Throttle calibration should not be needed out of the box. However, in order
to make the throttle range of different transmitters, the calibration of the
ESC is necessary:
Mount the ESC in an area that is well ventilated and isolated from
vibration and shock.
Connect the ESC motor wires to the motor red-to-red and black-to-black.
Plug the receiver into the throttle channel of the receiver.
Before plugging the battery into the ESC, make sure your transmitter is
on and the throttle trim is set to zero.
Connect the battery to the ESC. The vehicle will be powered on when the
battery is connected.
CAUTION: Keep all body parts and loose clothing away from any
moving parts while the battery is connected to the ESC.
CAUTION: Always connect the ESC only to a proper power
source that has the correct voltage and polarity. Incorrect
voltages or reversed polarity will damage the ESC. Damage to the ESC
caused by improper voltage or polarity is not covered under warranty.
Test forward and reverse control using the transmitter.
To calibrate the ESC:
Power the transmitter on and set the throttle control to neutral.
Connect the battery to the ESC and wait 3 seconds to let the ESC initiate
a self-test and automatic throttle calibration.
• The ESC is ready to run when a long beep sound is emitted from the motor.
Always disconnect the battery when the vehicle is not in use.
NOTES
The drag brake is set to 100% from the factory.
The LiPo cut-off is set to “ON” from the factory.
Suitable battery size range:
5.75” x .94-1.2” (147mm x 24-32mm)
Adjust the tray to the appropriate size to fi t the vehicle battery.
ESC SPECIFICATIONS
Input Voltage 2-3S LiPo, 5-9 Cells NiMH/NiCd
Size 46.5mm x 34mm x 28.5mm
Weight 70g
Motor Limit 12T 2S/18T 3S
On-Resistance FET .002
Rated/Peak Current 180A
Braking Current 90A
BEC Voltage/A 6.0V 3.0A Peak
PWM Frequency 1KHz
ESC SOUND STATUS
1 Short Beep Battery is NiMH/NiCd
2 Short Beeps Battery is 2S LiPo
3 Short Beeps Battery is 3S LiPo
1 Long Beep
Self-test and throttle calibration
is OK and ESC is ready to run
11
EN
TROUBLESHOOTING
GEAR RATIOS
NOTES
Spur/Pinion Gear Ration Chart - LCX Transmission
12 13 14 15 16 17 18
56 45.50 42.00 39.00 36.40 34.13 32.12 30.33
60 48.75 45.00 41.79 39.00 36.56
PROBLEM POSSIBLE CAUSE SOLUTION
Vehicle does not move
Batteries are not installed properly in the
transmitter
Ensure the transmitter batteries are properly installed
Weak or no battery in the vehicle Install a freshly charged vehicle battery
Damaged motor Replace the motor
Frayed or broken wiring Replace any damaged wiring
ESC is shut down by heat protection circuit Allow the ESC to cool down completely
Loss of vehicle control
Improper antenna placement
Ensure the transmitter antenna is not blocked and the receiver
antenna is located properly
Weak or no batteries in the transmitter or
vehicle
Install a freshly charged vehicle battery and new transmitter
batteries
Neutral or trim position is incorrect Adjust the steering trim
Receiver and/or battery not connected
properly
Check all receiver and battery connections
Steering and/or throttle function is reversed
Servo travel is reversed at the transmitter Set the transmitter servo reversing switch to the correct position
Motor wires are not connected properly Check all motor wires for correct polarity and secure connection
12
EN
What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the
product purchased (the “Product”) will be free from defects in materials
and workmanship at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage,
(ii) damage due to acts of God, accident, misuse, abuse, negligence,
commercial use, or due to improper use, installation, operation or
maintenance, (iii) modifi cation of or to any part of the Product, (iv) attempted
service by anyone other than a Horizon Hobby authorized service center, (v)
Product not purchased from an authorized Horizon dealer, or (vi) Product not
compliant with applicable technical regulations or (vii) use that violates any
applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO
OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS
ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT
LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED
THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE
PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall
be that Horizon will, at its option, either (i) service, or (ii) replace, any
Product determined by Horizon to be defective. Horizon reserves the right
to inspect any and all Product(s) involved in a warranty claim. Service
or replacement decisions are at the sole discretion of Horizon. Proof of
purchase is required for all warranty claims. SERVICE OR REPLACEMENT
AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND
EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION
OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH
CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT
LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in
no event shall the liability of Horizon exceed the individual price of the
Product on which liability is asserted. As Horizon has no control over use,
setup, fi nal assembly, modifi cation or misuse, no liability shall be assumed
nor accepted for any resulting damage or injury. By the act of use, setup
or assembly, the user accepts all resulting liability. If you as the purchaser
or user are not prepared to accept the liability associated with the use of
the Product, purchaser is advised to return the Product immediately in new
and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to confl ict of law
principals). This warranty gives you specifi c legal rights, and you may also
have other rights which vary from state to state. Horizon reserves the right to
change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty
support or service. Once assembly, setup or use of the Product has been
started, you must contact your local distributor or Horizon directly. This
will enable Horizon to better answer your questions and service you in
the event that you may need any assistance. For questions or assistance,
please visit our website at www.horizonhobby.com, submit a Product
Support Inquiry, or call the toll free telephone number referenced in the
Warranty and Service Contact Information section to speak with a Product
Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the
country you live and use the Product in, please use the Horizon Online
Service Request submission process found on our website or call Horizon
to obtain a Return Merchandise Authorization (RMA) number. Pack the
Product securely using a shipping carton. Please note that original boxes
may be included, but are not designed to withstand the rigors of shipping
without additional protection. Ship via a carrier that provides tracking
and insurance for lost or damaged parcels, as Horizon is not responsible
for merchandise until it arrives and is accepted at our facility. An Online
Service Request is available at http://www.horizonhobby.com/content/
service-center_render-service-center. If you do not have internet access,
please contact Horizon Product Support to obtain a RMA number along
with instructions for submitting your product for service. When calling
Horizon, you will be asked to provide your complete name, street address,
email address and phone number where you can be reached during
business hours. When sending product into Horizon, please include
your RMA number, a list of the included items, and a brief summary of
the problem. A copy of your original sales receipt must be included for
warranty consideration. Be sure your name, address, and RMA number are
clearly written on the outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue
with a Li-Po battery, please contact the appropriate Horizon Product
Support offi ce.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt
verifying the proof-of-purchase date. Provided warranty conditions have
been met, your Product will be serviced or replaced free of charge.
Service or replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be completed
and payment will be required without notifi cation or estimate of the
expense unless the expense exceeds 50% of the retail purchase cost. By
submitting the item for service you are agreeing to payment of the service
without notifi cation. Service estimates are available upon request. You
must include this request with your item submitted for service. Non-
warranty service estimates will be billed a minimum of 1/2 hour of labor. In
addition you will be billed for return freight. Horizon accepts money orders
and cashier’s checks, as well as Visa, MasterCard, American Express,
and Discover cards. By submitting any item to Horizon for service, you are
agreeing to Horizon’s Terms and Conditions found on our website http://
www.horizonhobby.com/content/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the
country of use and ownership. If received, a non-compliant Product will
not be serviced. Further, the sender will be responsible for arranging
return shipment of the un-serviced Product, through a carrier of the
sender’s choice and at the sender’s expense. Horizon will hold non-
compliant Product for a period of 60 days from notifi cation, after which
it will be discarded.
10/15
Country of Purchase Horizon Hobby Contact Information Address
United States of America
Horizon Service Center
(Repairs and Repair Requests)
servicecenter.horizonhobby.com/RequestForm/
2904 Research Rd
Champaign, IL 61822
Horizon Product Support
(Product Technical Assistance)
productsupport@horizonhobby.com
877-504-0233
Sales
websales@horizonhobby.com
800-338-4639
European Union
Horizon Technischer Service service@horizonhobby.eu
Hanskampring 9
D 22885 Barsbüttel, Germany
Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100
LIMITED WARRANTY
WARRANTY AND SERVICE CONTACT INFORMATION
13
EN
INSTRUCTIONS FOR DISPOSAL OF WEEE BY USERS IN THE EUROPEAN UNION
This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it
over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of
your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects
human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your
local city offi ce, your household waste disposal service or where you purchased the product.
EU COMPLIANCE STATEMENT:
Axial Wraith 1.9 (AXI90074)
Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the RED
and EMC Directives.
A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-compliance.
FCC INFORMATION
IC INFORMATION
COMPLIANCE INFORMATION FOR THE EUROPEAN UNION
CAN ICES-3 (B)/NMB-3(B)
IC: 21682-SSTC9202
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
FCC ID: 2AI3D-SS0001
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations
governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.
SUPPLIER’S DECLARATION OF CONFORMITY
Axial Wraith 1.9 (AXI90074)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Horizon Hobby, LLC
4105 Fieldstone Rd.,
Champaign, IL 61822
Email: compliance@horizonhobby.com
Web: HorizonHobby.com
50
PARTS REFERENCE // TEILEREFERENZ // RÉFÉRENCES DES PIÈCES // RIFERIMENTO COMPONENTI
AX80018 (x2)
Hardware parts tree
Hardware-Teilebaum
Arbre des pièces de quincaillerie
Set bulloneria
AX31577 (x2)
Shock cap parts tree
Stoßdämpferkappe Teilebaum
Arbre des pièces de capuchons d’amortisseurs
Set tappi ammortizzatore
AX31576 (x1)
10mm shock parts tree
10mm Stoßdämpfer-Teilebaum
Arbre des pièces d’amortisseurs 10mm
Set ricambi per ammortizzatore 10 mm
AXI231001 (x1)
Wraith 1.9 skid plate
Wraith 1.9 Gleitbrett
Plaque de protection Wraith 1.9
Piastra di protezione Wraith 1.9
AXI231002 (x1)
Wraith 1.9 receiver box parts tree
Wraith 1.9 Empfängerbox Teilebaum
Arbre des pièces du boîtier de récepteur Wraith 1.9
Set ricambi vano ricevitore Wraith 1.9
AXI230001 (x1)
Wraith 1.9 grille set
Wraith 1.9 Kühlergrillset
Ensemble de calandre Wraith 1.9
Set griglia Wraith 1.9
AXI231001 (x1)
Wraith 1.9 battery tray
Wraith 1.9 Akkuhalterung
Support de batterie Wraith 1.9
Vassoio portabatteria Wraith 1.9
AXI43001 (x4)
11.9 KMC Machete wheel 26mm, satin chrome
11.9 KMC Macheten-Rad 26mm, matt verchromt
Roue Machete 11.9 KMC, 26mm, chrome satiné
Ruota 11.9 KMC Machete 26 mm, cromo satinato
AX31592 (x1)
AR44 Solid axle housing, front and rear
AR44 solides Achsgehäuse, vorne und hinten
Carter d’essieu solide AR44, avant et arrière
Alloggiamento solido assale AR44, anteriore e posteriore
AX80030 (x2)
61-90mm shock body
61-90mm Stoßdämpfergehäuse
Corps d’amortisseur 61-90mm
Scocca ammortizzatore 61-90 mm
AX31589 (x1)
AR44 Differential Covers (red)
AR44 Differenzialgehäuse (rot)
Couvercles de différentiel AR44 (rouge)
Carter differenziale AR44 (rosso)
AX31381 (x1)
AR44 Steering knuckles
AR44 Lenkrollen
Rotules de direction AR44
Fuso a snodo AR44
51
AX80087 (x1)
Rock buggy main frame
Rock-Buggy-Hauptrahmen
Châssis principal Rock Buggy
Telaio principale Rock buggy
AX80089 (x1)
Rock buggy front end 2
Rock-Buggy-Front 2
Train avant Rock Buggy 2
Parte anteriore Rock buggy 2
AX80077-01 (x1)
Rock buggy front end 1
Rock-Buggy-Front 1
Train avant du Rock Buggy 1
Parte anteriore Rock buggy 1
AX80082 (x1)
Rock buggy battery brace
Rock-Buggy-Akku-Halterung
Support de batterie Rock Buggy
Supporto batteria Rock buggy
AX80076 (x1)
Rock buggy rear brace set
Hinteres Rock-Buggy-Stützenset
Ensemble de support arrière Rock Buggy
Set bretella posteriore Rock buggy
AX80075 (x1)
Wraith tube frame, top
Wraith Rohrgestell, oben
Châssis tubulaire Wraith, haut
Telaio tubolare Wraith, parte superiore
AX80088 (x1)
Rock buggy main frame
Rock-Buggy-Hauptrahmen
Châssis principal Rock Buggy
Telaio principale Rock buggy
AXI231001 (x1)
Wraith 1.9 lower rails
Wraith 1.9 untere Schienen
Rails inférieurs Wraith 1.9
Guide inferiori Wraith 1.9
52
AX31049 (x1)
Helmet set, black
Helm-Set, schwarz
Ensemble de casque, noir
Set elmetti, nero
AX31586 (x2)
WB8-HD Standard driveshaft
WB8-HD Standard-Antriebswelle
Arbre de transmission standard WB8-HD
Albero di trasmissione standard WB8-HD
AX31531 (x2)
LCX Transmission case, silver
LCX Getriebeabdeckung, silber
Boîtier de transmission LCX, argenté
Scatola del cambio LCX, argento
AX8080 (x1)
Hub cover set, satin chrome
Nabenabdeckungsset, matt verchromt
Ensemble de caches de moyeu, chrome satiné
Set coprimozzo, cromo satinato
AX31591 (x1)
Chassis Brace set
Karosseriestrebensatz
Ensemble de support de carrosserie
Set bretella telaio
AX31571 (x1)
CRC JK Front bumper
CRC JK Frontstoßstange
Pare-chocs avant CRC JK
Paraurti anteriore CRC JK
AX31536 (x1)
SCX10 II Steering link
SCX10 II-Lenkstange
Tringlerie de direction SCX10 II
Collegamento sterzo SCX10 II
AX31533 (x1)
SCX10 II Upper links set
SCX10 II oberes Verbindungsgliedset
Ensemble de timonerie supérieure SCX10 II
Set leveraggi, superiore SCX10 II
AX31552 (x1)
SCX10 II Lower links set
SCX10 II unteres Verbindungsgliedset
Ensemble de timonerie inférieure SCX10 II
Set leveraggi, inferiore SCX10 II
53
AX30724 (x2)
Pinion gear, 13T, 32P
Zahnradgetriebe, 13T, 32P
Engrenage à pignons, 13T, 32P
Pignone, 13T, 32P
AX30427 (x4)
Narrow 12mm aluminum hub
Schmale Aluminium-Nabe, 12mm
Moyeu étroit en aluminium de 12mm
Mozzo in alluminio stretto, 12 mm
AX31026 (x2)
Slipper plate washer, 33 x 5 x 1.5mm
Gleitplattenunterlegscheibe, 33 x 5 x 1,5mm
Rondelle de plaque de sabot, 33 x 5 x 1,5mm
Rondella piastra pattino, 33 x 5 x 1,5 mm
AX31471 (x2)
Axle, 12 x 36mm
Achse, 12 x 36mm
Essieu, 12x36mm
Assale ,12 x 36 mm
AX31027 (x1)
Spur gear, 56T, 32P
Stirnrad, 56T, 32P
Engrenage cylindrique, 56T, 32P
Corona, 56T, 32P
AX31585 (x1)
48P Gear set, 28T, 52T
48P Getriebesatz, 28T, 52T
Ensemble d’engrenage 48P, 28T, 52T
Set ingranaggi 48P, 28T, 52T
AX30146 (x4)
Shock shaft, 3 x 50mm
Kolbenstange, 3 x 50mm
Bras d’amortisseur, 3 x 50mm
Albero ammortizzatore, 3 x 50 mm
AX31539 (x1)
Slipper drive gear shaft
Gleitantriebswelle
Arbre d’engrenage d’entraînement du sabot
Albero trasmissione pattino
AX31472 (x2)
Solid Axle Dogbone, 6 x 73,5mm
Solid Axle Dogbone, 6 x 73,5mm
Dogbone d’essieu solide, 6x73,5mm
Dogbone assale solido, 6 x 73,5 mm
AX31408 (x2)
AR44 Straight axle shaft, 5 x 106mm
AR44 Gerade Achswelle, 5 x 106 mm
Arbre d’essieu droit AR44, 5 x 106mm
Semiasse lineare AR44, 5 x 106 mm
AX31068 (x2)
Slipper pad, 32.8 x 15.2 x 1mm
Gleitkissen 32,8 x 15,2 x 1mm
Sabot de piston, 32,8 x 15,2 x 1mm
Pattino scorrevole, 32,8 x 15,2 x 1 mm
AX31148 (x4)
WB8-HD Driveshaft coupler set
WB8-HD-Antriebswellenkupplungssatz
Ensemble de couplage d’arbre de
transmission WB8-HD
Set accoppiamento albero
trasmissione WB8-HD
AX31530 (x2)
AR44 Locker bevel gear set, 30T/8T
AR44 Kegelradgetriebesatz, 30T/8T
Ensemble d’engrenage conique de
blocage AR44, 30T/8T
Set coppia conica blocco AR44,
30T/8T
AX31441 (x4)
Spring, 12.5 x 60mm, 1.13 lbs, white
Feder, 12,5 x 60 mm, 0,5 kg, weiß
Ressort, 12,5 x 60mm, 0,12Nm (1,13lb-po), blanc
Molla, 12,5 x 60 mm, 512 gr (1,13 libbre), bianco
AX30413 (x1)
Slipper spring, 8.5 x 12
Gleitfeder, 8,5 x 12
Ressort de sabot, 8,5 x 12
Molla pattino, 8,5 x 12
AX31083 (x1)
Radio box seals
Funkbox-Dichtungen
Joints du boîtier de radio
Guarnizioni vano radiocomando
AX30435 (x1)
Steel outdrive shaft
Stahl-Flexwelle
Arbre de transmission extérieur en acier
Albero outdrive acciaio
AX30394 (x1)
Drive gear, 20T
Antriebszahnrad, 20T
Engrenage d’entraînement, 20T
Ingranaggio trasmissione, 20T
54
AXA1179 (x8)
AXA1059 (x2)
AXA0286 (x6)
AXA180 (x4)
AXA291 (x1)
AXA0109 (x6)
AX31403 (x4)
AXA063 (x4)
AXA065 (x4)
AXA0113 (x1)
AXA114 (x12)
AXA115 (x8)
AXA116 (x9)
AXA117 (x12)
AXA119 (x1)
AXA120 (x2)
AXA441 (x4)
AXA440 (x2)
AXA439 (x4)
AXA438 (x2)
AXA437 (x1)
AXA436 (x6)
AXA0422 (x1)
AXA148 (x4)
AXA146 (x8)
AXA144 (x4)
AXA054 (x2)
AXA053 (x4)
AX3139 (x8)
AXA0023 (x2)
AXA013 (x11)
AXA1163 (x4)
AX30162 (x1)
AX30163 (x4)
AX31283 (x4)
AX30190 (x1)
AXA1070 (x1)
AXA1392 (x8)
AXA1045 (x5)
AXA1218 (x4)
AXA1221 (x8)
AXA1225 (x2)
AXA1230 (x2)
AX31406 (x4)
AX31407 (x2)
55
AXA117
AXA0439
AX31576
AX31576
AXA117
AXA0439
AXA117
AXA119
AX31536
AX80018
AX80018
AX80018
AX80018
AX80018
AX80018
AX80018
AX80018
AX80018
AX80018
AX80018
AX80018
AX31536
AXA117
AXA117
AXA120
AXA113
AXA1070
AX31589
AX31406
AX31530
AX31407
AX31472
AX31471
AX31381
AXA1230
AX31472
AXA1221
AXA1221
AXA1221
AX31403
AX31403
AX31403
AXA1221
AX31586
AX31399
AX31586
AX31586
AX31586
AX31586
AXA144
AXA144
AX31148
AX31148
AX31148
AX31148
AX31148
AX31148
AXA0286
AXA0286
AX31028
AX31028
AX31592
AX31552
AX31533
AX31552
AX31406
AX31590
AX80018
AXA117
AXA116
AX31471
AX31381
AXA1230
AXA1221
AX31403
AX31589
AX31406
AX31406
AX31530
AX31407
AXA1221
AX31586
AX31586
AX31586
AXA144
AXA144
AXA117
AXA117
AXA117
AXA0439
AXA0439
AX31576
AX31576
AX31148
AX31148
AX80018
AX80018
AXA1221
AXA1221
AX31408
AX31408
AX80018
AX80018
AX80018
AX80018
AXA0286
AXA0286
AX31028
AX31028
AX31592
AX31399
AX31533
AX31533
AX31552
AX31552
AXA115
AXA115
EXPLODED VIEWS // EXPLOSIONSZEICHNUNGEN // VUES ÉCLATÉES // VISTE ESPLOSE
FRONT AXLE
VORDERACHSE
ESSIEU AVANT
ASSALE ANTERIORE
REAR AXLE
HINTERACHSE
ESSIEU ARRIÈRE
ASSALE POSTERIORE
56
AX31068
AX31027
AX31027
AXA1045
AX31068
AX31026
AX30435
AX30435
AX31585
AX31585
AXA0109
AXA1225
AXA013
AXA0023
AXA146
AX30724
AXA291
AX31312
AX31531
AX31531
AX31539
AX31531
AX30190
AX30162
AXA1218
AXA1218
AXA1218
AXA1225
AX30394
AX31026
AX30413
AXA438
AXA441
AXA438
AX80088
AX80087
AX80089
AX80076
AX80077
AX80075
AX80082
AXA114
AXA114
AXA114
AXA063
AXA116
AXA116
AXA114
AXA054
AXA054
AX80089
AXI231002
AXI231001
AXI231001
AXI231001
AXI231001
AXI231001
AXI231001
AXI231001
AXI231001
AXI231001
AXI231001
AXA438
AXA438
AXA438
AXA438
AXA438
AXA115
AXA115
AXA438
AXA438
AXA438
AXA438
AXA116
AXA437
AXA437
AXA437
AXA437
AX80089
AXA438
AXA436
AXA436
TRANSMISSION
GETRIEBE
TRANSMISSION
TRASMISSIONE
CHASSIS
KAROSSERIE
CHÂSSIS
TELAIO
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26

Axial AXI90074T1 Le manuel du propriétaire

Catégorie
Jouets télécommandés
Taper
Le manuel du propriétaire

dans d''autres langues