TEAC W-865R Manuel utilisateur

D00933700A

Double Auto Reverse Cassette Deck

OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE

MANUAL DEL USUARIO

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

GEBRUIKSAANWIJZING

Z

W

-

865R

ENGLISH FRANÇAIS ESPAÑOL DEUTSCH

ITALIANO NEDERLANDS

2

CAUTION: TO REDUCE TH

E RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within

an equilateral triangle, is intended to alert the user

to the presence of uninsulated “dangerous voltage”

within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral triangle

is intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

• Read all of these Instructions.

• Save these Instructions for later use.

• Follow all Warnings and Instructions marked on the audio

equipment.

1) Read Instructions — All the safety and operating

instructions should be read before the product is operated.

2) Retain Instructions — The safety and operating instructions

should be retained for future reference.

3) Heed Warnings — All warnings on the product and in the

operating instructions should be adhered to.

4) Follow Instructions — All operating and use instructions

should be followed.

5) Cleaning — Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners. Use a

damp cloth for cleaning.

6) Attachments — Do not use attachments not recommended

by the product manufacturer as they may cause hazards.

7) Water and Moisture — Do not use this product near water

— for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a swimming pool; and

the like.

8) Accessories — Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall, causing

serious injury to a child or adult, and serious damage to the

product. Use only with a cart, stand, tripod, bracket, or table

recommended by the manufacturer, or sold with the product.

Any mounting of the product should follow the manufacturer’s

instructions, and should use a mounting accessory

recommended by the manufacturer.

9) A product and cart combination should be

moved with care. Quick stops, excessive force, and

uneven surfaces may cause the product and cart

combination to overturn.

10) Ventilation — Slots and openings in the cabinet are

provided for ventilation and to ensure reliable operation of the

product and to protect it from overheating, and these openings

must not be blocked or covered. The openings should never be

blocked by placing the product on a bed, sofa, rug, or other

similar surface. This product should not be placed in a built-in

installation such as a bookcase or rack unless proper ventilation

is provided or the manufacturer’s instructions have been adhered

to.

11) Power Sources — This product should be operated only

from the type of power source indicated on the marking label. If

you are not sure of the type of power supply to your home,

consult your product dealer or local power company. For

products intended to operate from battery power, or other

sources, refer to the operating instructions.

12) Grounding or Polarization — This product may be

equipped with a polarized alternating-current line plug (a plug

having one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you are

unable to insert the plug fully into the outlet, try reversing the

plug. If the plug should still fail to fit, contact your electrician to

replace your obsolete outlet. Do not defeat the safety purpose of

the polarized plug.

13) Power-Cord Protection — Power-supply cords should be

routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention

to cords at plugs, convenience receptacles, and the point where

they exit from the product.

14) Outdoor Antenna Grounding — If an outside antenna or

cable system is connected to the product, be sure the antenna or

cable system is grounded so as to provide some protection

against voltage surges and built-up static charges. Article 810 of

the National Electrical Code, ANSI/NFPA 70, provides information

with regard to proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an antenna discharge

unit, size of grounding conductors, location of antenna-

discharge unit, connection to grounding electrodes, and

requirements for the grounding electrode.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Section 820-40 of the NEC which provides

guidelines for proper grounding and, in particular, specifies that

the cable ground shall be connected to the grounding system of

the building, as close to the point of cable entry as practical.

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

NEC - NATIONAL ELECTRICAL CODE

ELECTRIC

SERVICE

EQUIPMENT

Example of Antenna Grounding

as per National Electrical

Code, ANSI/NFPA 70

GROUND

CLAMP

3

ENGLISH

CAUTION

<

DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO

EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS

ARE WITHIN!

<

IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE

PRODUCT UNTIL IT HAS BEEN REPAIRED.

<

Do not expose this apparatus to drips or splashes.

<

Do not place any objects filled with liquids, such as vases, on

the apparatus.

<

Do not install this apparatus in a confined space such as a

book case or similar unit.

<

The apparatus draws nominal non-operating power from the

AC outlet with its POWER switch in the off position.

<

The apparatus should be located close enough to the AC

outlet so that you can easily grasp the power cord plug at

any time.

<

An apparatus with Class

!

construction shall be connected to

an AC outlet with a protective grounding connection.

WARNING: TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following

measures:

• Reorient or relocate the equipment and/or the receiving

antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

CAUTION

Changes or modifications to this equipments not expressly

approved by TEAC CORPORATION for compliance will void the

user’s warranty.

For U.S.A.

15) Lightning — For added protection for this product during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line surges.

16) Power Lines — An outside antenna system should not be

located in the vicinity of overhead power lines or other electric

light or power circuits, or where it can fall into such power lines

or circuits. When installing an outside antenna system, extreme

care should be taken to keep from touching such power lines or

circuits as contact with them might be fatal.

17) Overloading — Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result in

risk of fire or electric shock.

18) Object and Liquid Entry — Never push objects of any kind

into this product through openings as they may touch dangerous

voltage points or short-out parts that could result in a fire or

electric shock. Never spill liquid of any kind on the product.

19) Servicing — Do not attempt to service this product yourself

as opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified service

personnel.

20) Damage Requiring Service — Unplug this product from

the wall outlet and refer servicing to qualified service personnel

under the following conditions:

a ) when the power-supply cord or plug is damaged.

b ) if liquid has been spilled, or objects have fallen into the

product.

c ) if the product has been exposed to rain or water.

d ) if the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper adjustment

of other controls may result in damage and will often require

extensive work by a qualified technician to restore the product to

its normal operation.

e ) if the product has been dropped or damaged in any way.

f ) when the product exhibits a distinct change in performance _

this indicates a need for service.

21) Replacement Parts — When replacement parts are

required, be sure the service technician has used replacement

parts specified by the manufacturer or have the same

characteristics as the original part. Unauthorized substitutions

may result in fire, electric shock, or other hazards.

22) Safety Check — Upon completion of any service or repairs

to this product, ask the service technician to perform safety

checks to determine that the product is in proper operating

condition.

23) Wall or Ceiling Mounting — The product should be

mounted to a wall or ceiling only as recommended by the

manufacturer.

24) Heat — The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

4

Table of Contents

Thank you for choosing TEAC. Read this manual carefully

to get the best performance from this unit.

Before Use

Read this before operation

< As the unit may become warm during operation, always leave

sufficient space around the unit for ventilation.

< The voltage supplied to the unit should match the voltage as

printed on the rear panel. If you are in any doubt regarding

this matter, consult an electrician.

<

Choose the installation location of your unit carefully. Avoid

placing it in direct sunlight or close to a source of heat. Avoid

locations subject to vibrations and excessive dust, heat, cold

or moisture.

<

Do not place the unit on any other electronic components.

<

Do not open the cabinet as this might result in damage to the

circuitry or electrical shock. If a foreign object should fall into

the unit, contact your dealer or service company as soon as

possible.

<

When removing the power plug from a wall outlet, always

pull directly on the plug. Do not pull on the line cord.

< Do not attempt to clean the unit with chemical solvents as

this might damage the finish. Use a clean, dry, lint-free cloth.

< Keep this manual in a safe place for future reference.

Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Handling Cassette Tapes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Using the Remote Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . 7

Identifying the Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Playback (either TAPE I or TAPE II) . . . . . . . . . . . . . . . . . . . . . . 11

Continuous Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Blank Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Song Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Intro Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Recording (either TAPE I or TAPE II) . . . . . . . . . . . . . . . . . . . . . 16

Mic Mixing Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Continuous Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Dubbing (from TAPE I to TAPE II). . . . . . . . . . . . . . . . . . . . . . . 20

Parallel Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Editing during Dubbing (only at normal speed) . . . . . . . . . . . . 21

Synchro Reverse Dubbing (from TAPE I to TAPE II) . . . . . . . . . . 22

Timer-Controlled Playback and Recording . . . . . . . . . . . . . . . . 24

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

ENGLISH

5

Handling Cassette Tapes

Caution

< Do not open the cassette or pull the tape out of the cassette.

<

Do not touch the tape surface.

<

Do not use or store the tape in a humid or dusty place.

<

Keep the tape away from any magnetic sources, such as

speakers or TVs, otherwise noise may be produced during

playback or important recordings may be erased.

Cassette tapes that you should not use

Poor performance, errors, or malfunctions may result if you

use any of the tapes described below. Some of these tapes

may also cause tape clog problems that can damage the tape

transport mechanism.

Cassettes that are imperfectly shaped

Do not use a deformed cassette or one that has unstable tape

movement or makes a strange sound during fast-forward or

rewind.

Long play tapes

Do not use C-120 or longer tapes. These tapes are very thin

and can easily stretch or get tangled in the tape transport

mechanism.

Endless tapes

Do not use these tapes because they can easily get tangled in

the tape transport mechanism.

Automatic tape type detection function

This cassette deck can detect what type of tape is being used

based on the detection holes in the cassette shell. Be sure to

use cassettes with detection holes.

<

With this cassette deck, you can play back normal (Type I),

chrome (Type

II) and metal (Type IV ) tapes. For recording, use

normal (Type

I) or chrome (Type II) tapes.

<

Each deck (TAPE I and TAPE II) is equipped with its own auto

tape type detection function, so you can use different types

of tape at the same time.

Tape slack

Slack can cause the tape to get tangled in the capstan or

other rotating parts. To prevent this, take up all tape slack

using a pencil or the like inserted into the reel hole.

Metal

(

Type IV

)

Automatic tape type detection holes

CrO

2

(

Type

II

)

Normal

(

Type

I

)

Accidental erasure prevention tabs

Tabs on top of the cassette shell allow you to prevent

important recordings from being erased by mistake. There are

two tabs on each cassette shell: one for side “A” and the

other for side “B”.

Once these tabs have been removed using a screwdriver or

the like, there is absolutely no chance of the recording

function being activated.

To record on a cassette whose tab has been broken off, stick

a piece of adhesive tape over the hole. Be careful not to block

the tape type detection holes.

Dolby NR

Dolby NR is designed to reduce tape hiss, a noise introduced

during the recording and playback processes. This cassette

deck is equipped with Dolby B-type Noise Reduction.

The Dolby NR system affects both recording and playback

quality. In playback, be sure to set the DOLBY NR switch to

the same position used when the recording was made.

Manufactured under license from Dolby Laboratories.

HX Pro headroom extension originated by Bang and Olufsen.

Dolby, HX Pro, and the double-D symbol are trademarks of

Dolby Laboratories.

Accidental erasure prevention

tab for side “A”

Side “A”

6

Connections

Precautions

<

Plug the power cord into an AC outlet only after having made all other connections.

<

Read the instructions of each component you intend to use with this unit.

Voltage Conversion

(General export models only)

Be sure to remove the power cord from the AC outlet

before repositioning the voltage converter switch.

1. Locate the voltage selector on the rear panel.

2.Using a flat-bladed screwdriver, set to the

appropriate 230V or 120V position according to your

area.

IN NORTH AMERICA USE ONLY ON 120 V SUPPLY.

Amplifier

LLRR

PLAYREC

TAPE

BA

ENGLISH

7

LINE IN and LINE OUT jacks

Use the supplied RCA cables to make connections between

this unit and your amplifier. Make sure to connect:

White plug to White jack (L: left channel)

Red plug to Red jack (R: right channel)

< Plugs must be firmly inserted into the corresponding jacks.

Do not bundle the RCA cables together with the power cord

and speaker cables. Doing so will degrade sound quality or

generate noise.

AC power cord

Plug this AC power cord into an AC wall socket.

<

Be sure to connect the power cord to an AC outlet which

supplies the correct voltage.

< Hold the power plug when plugging or unplugging the

power cord. Never pull or yank on the power cord.

< Unplug the power cord when you are not going to use the

unit for some time.

B

A

Using the Remote Control Unit

Cautions when using the remote control unit

<

Point the remote control unit at the remote sensor of the

cassette deck and operate the remote control unit at a

distance of no more than 5 meters. Do not place objects

between the remote control unit and remote sensor.

<

Direct sunlight or very bright light will reduce the sensitivity of

the remote sensor. If this is the case, use the control buttons

on the cassette deck instead of the remote buttons.

<

It is possible that other infrared-ray-sensitive equipment

nearby may malfunction when you operate the remote

control.

Loading batteries into the remote control unit

Remove the lid of the battery compartment, load two “AA”

sized batteries in the indicated directions, and then replace

the lid. When inserting batteries, be sure to observe proper

polarity (+ and –).

If you have to put the remote control unit quite close to the

remote sensor or if any remote buttons do not work, then

the batteries are no longer fit for use and must be

replaced.

Be sure to always replace both batteries at once.

Important Cautions for Handling Batteries

Improper battery use can result in leakage or rupture. Observe

the following instructions:

< Load the batteries in the correct direction as indicated in the

battery compartment.

< Do not mix old and new batteries, or mix different types or

brands of battery.

< Do not heat, disassemble, or throw batteries into fire or

water.

< Do not store or carry batteries together with other small metal

objects. Doing so can cause battery shorting, leakage or

rupture.

<

Do not try to recharge dry batteries.

<

When the cassette deck is not going to be used for a long

time (more than one month), take the batteries out of the

battery compartment.

<

If leakage into the battery compartment is observed, wipe up

any liquid inside the compartment and load new batteries.

8

Identifying the Parts

O

Q

RSTO PP

A

C

B

D

E NF I J K L

M

G

GH

G

H

M

G

P

L

J

I

P

ENGLISH

9

In this manual we only refer to the buttons on the cassette deck

itself. However, their remote counterparts can be used in the

same way.

Power switch

This switch toggles the unit on/off.

Reverse mode switch (REV MODE)

This switch is used to switch between reverse modes.

TIMER switch

This switch is provided for use with a commercially available

audio timer, to allow timer controlled recording or playback.

Normally, leave this switch to the OFF position.

DOLBY NR switch

This switch toggles the Dolby Noise Reduction system on/off.

In playback you need to set this switch to the same position

as when the recording was made.

TAPE I compartment

Remote sensor

This receives remote commands. When using the remote

control unit, point it at this sensor.

Counter clear buttons (CLEAR I and CLEAR II)

Pressing these buttons reset the tape counter readings for

TAPE I and TAPE II, respectively.

INTRO CHECK button

Pressing this button allows you to identify recorded segments

by listening to the first 15 seconds of each segment.

Synchro reverse button (SYNC REV)

Pressing this button activates the synchro reverse dubbing

function.

BLANK SCAN button

This button toggles Blank Scan on/off.

Display

This shows tape counters, level meters, etc.

Parallel record button (PARALLEL REC)

This button lets you simultaneously record on both decks.

Dubbing start button (DUB START)

This button is used when copying the contents of a tape from

TAPE I to TAPE II, either at normal or high speed.

On the remote control unit a pair of buttons is provided for

each speed. You need to press both buttons at the same

time.

M

L

K

J

I

H

G

F

E

D

C

B

The equipment draws nominal non-operating power from

the AC outlet with its POWER switch in the OFF position.

A

TAPE II compartment

EJECT buttons

Pressing these buttons opens the TAPE I and TAPE II

compartments.

Tape transport control buttons

RECORD

Pressing this button shifts the corresponding deck to record-

pause mode.

When you use the remote control unit, you need to press a

pair of buttons at the same time to shift either deck to record-

pause mode.

PAUSE

Pressing this button temporarily stops playback or recording.

Recording mute (REC MUTE)

This button is for creating the 4-second blank space needed

for proper operation of the Computomatic Program Search

(CPS) function.

m

/,

Fast-forward/Rewind

H

Stop of playback/record

h

/ y

Reverse side play/Forward side play

Headphones jack (PHONES)

Plug your headphones into this jack.

PITCH CONTROL

This control is used to vary the playback speed.

REC LEVEL control

This control is used to adjust the recording level.

MIC jack and level control

Insert your microphone into this jack and use the knob to

adjust the level of mic input.

<

The MIC jack is mono. You cannot use a stereo microphone

with this cassette deck.

T

S

R

Q

P

O

N

10

Peak level meter

This shows recording and playback levels.

SYNC REV

This indicator lights when the synchro reverse dubbing

function is switched on.

PARALLEL

This indicator lights to indicate parallel recording is taking

place.

BLANK SCAN

This indicator lights to indicate the corresponding function is

switched on.

Playback/recording direction indicator of TAPE I deck

Pause indicator

This indicator lights when the TAPE I deck is temporarily

stopped.

Tape counter of TAPE I deck

The tape counter indicates the relative position of the tape.

You can reset the counter to zero whenever you want.

During a CPS function, the tape counter shows “CP” and

your specified number of songs to skip ahead or back.

Record indicator

This indicator lights when the TAPE I deck is in record mode.

Play indicator

This indicator lights when the TAPE I deck is in play mode.

Dubbing indicator

“NORMAL DUB” lights during normal speed dubbing, and

“HIGH DUB” lights during high speed dubbing.

j

i

h

g

f

e

d

c

b

a

SYNC REV BLANK SCAN

PARALLEL

HIGH DUB

NORM DUB

REC

PLAY

REC

PLAY

g

i

j

k

m

e ohf n

l

a b dc

Display

Play indicator

This indicator lights when the TAPE II deck is in play mode.

Record indicator

This indicator lights when the TAPE II deck is in record mode.

Tape counter of TAPE II deck

The tape counter indicates the relative position of the tape.

You can reset the counter to zero whenever you want.

During CPS operation, the tape counter shows “CP” and the

number of songs you have specified to skip ahead or back.

Pause indicator

This indicator lights when the TAPE II deck is temporarily

stopped.

Playback/recording direction indicator of TAPE II deck

o

n

m

l

k

Select a reverse mode setting using the REV MODE

switch.

You have a choice of three settings:

u

: One way mode

Set the switch to this position to play back only one side.

j

: Two way mode

Set the switch to this position to play back both sides of

the tape in one session. When playback reaches the end of

side “A”, the playback direction is automatically reversed,

and playback continues on side “B”.

p

: Repeat mode

Set the switch to this position and both sides of the tape

are played back as many as 5 times.

Set the DOLBY NR switch.

Set the switch to the ON position when playing back tapes

recorded with Dolby NR.

To play tapes recorded without Dolby NR, set the switch to

the OFF position.

Press the play button (h or y).

y

: Pressing this button starts playback from side “A”.

Playback stops when reaching the end of side “A” if the

reverse mode is set to u

. If the reverse mode is set to

j

, playback continues on side “B”, stopping at the end

of side “B”. If the reverse mode is set to p

, playback

cycles through both tape sides 5 times.

h

: Pressing this button starts playback from side “B”.

Playback stops when reaching the end of side “B” if the

reverse mode is set to either u

or j. If the reverse

mode is set to p

, side “B” is played back, and then

playback cycles through both tape sides 4 times.

5

4

3

ENGLISH

11

Playback (either TAPE I or TAPE II) 1

13

4

2 2

5 5

Switch on the power.

Load a pre-recorded tape into the TAPE I or II deck.

Press the EJECT button (L ) to open the cassette

compartment. Insert the cassette tape with its open edge

facing down, the desired side facing you. Then, close the

cassette compartment by pushing on its front part.

<

This cassette deck can play back Normal (Type I), Chrome

(Type II) and Metal (Type IV) tapes.

For the sake of simplicity, we refer to the tape side facing you

as Side “A” and to the tape side facing away as Side “B”.

When you insert a cassette with Sides “A” and “B” reversed,

Side “A” should read Side “B” and Side “B” should read Side

“A”.

2

1

Side “A” facing you

12

Playback (either TAPE I or TAPE II) 2

EA A F

B D DB

C

To stop playback

Press the stop button (H).

To stop playback temporarily

Press the PAUSE button.

To resume playback, press the PAUSE button again, or press

the play button (h

or y).

< While playback is paused, pressing the play button whose

direction is opposite to the indicator (h

or y) on the display,

will switch the playback direction. This does not release the

pause function. Press PAUSE or the same play button (h

or

y

) again to start playback on the other side of the tape.

Fast forward/Rewind

Press the m or , button while in stop mode to fast wind

the tape.

To stop the fast winding tape, press the stop button (H).

C

B

A

Tape counter

Press the CLEAR I or II button to reset the tape counter to

0000. You can use this function for easy relocation of any

desired point on the tape.

Pitch control (TAPE I deck only)

This control varies the pitch of the music during playback.

(This control does not work during recording or dubbing.)

Turning the pitch control knob clockwise increases the

playback speed and raises the pitch up to +10%.

Turning the pitch control knob counterclockwise reduces the

playback speed and lowers the pitch by a maximum of –10%.

To listen through headphones

Plug your headphones into the PHONES jack, and put on the

headphones.

Plugging into the PHONES jack does not disable the line

outputs.

CAUTION

There is no level control for the headphones output. Beware

that sudden loud sounds may occur depending on recorded

material. You should avoid prolonged exposure to high

volume sound as this can damage your hearing.

F

E

SYNC REV BLANK SCAN

PARALLEL

HIGH DUB

NORM DUB

REC

PLAY

REC

PLAY

D

ENGLISH

13

Continuous Playback

3

41 14

2

Continuous playback can be performed between TAPE I and

TAPE II. When one tape is played back to the end, the other tape

automatically starts playback, in a relay fashion.

Load pre-recorded tapes into the TAPE I and TAPE II

compartments.

Set the Dolby NR switch.

Always set the Dolby NR switch to the same position that was

used for recording.

Set the REV MODE switch to the p (CONT PLAY)

position.

Press the play button (h

or y) of the deck you want to

start first.

You can start continuous playback from either TAPE I or

TAPE II.

Playback cycles through four tape sides as follows:

Playback will automatically stop when both sides of both

tapes have been played back 5 times continuously.

TAPE I Side “A” w

Side “B”

2x

TAPE II Side “B” s Side “A”

4

3

2

1

Blank Scan

The Blank Scan function detects 10 seconds or more of blank

and skips over it.

To activate this function, press the BLANK SCAN button followed

by the desired play button (h

or y).

< The BLANK SCAN indicator lights when this function is

activated.

< To disable this function, press the BLANK SCAN button again.

The indicator turns off.

< Very quiet passages in music are likely to be identified as

blanks. If you are worried about this, switch off Blank Scan.

14

Song Search

m,m,

This cassette deck is equipped with the Computomatic

Program Search (CPS) function. This function detects blank

spaces (longer than 4 seconds) between songs and fast-winds

the tape in the forward or backward direction skipping over

the specified number of songs, thus allowing direct access to

the beginning of a desired song. CPS can skip up to 20 songs

ahead of or behind the current song.

When you press the m

or , button during playback, the

tape counter reads “CP 01” and the tape starts running at

high speed in the pressed direction. Each time you press the

same direction button, the displayed number increases by one

integer. The number decreases as you press the opposite

direction button.

<

If you are listening to a song and want to go back to the

previous song, press the locator button opposite to the

playback direction twice. Pressing it just once will take you

back to the beginning of the current song. Each additional

press of the button will take you back one song.

Display of TAPE I

SYNC REV BLANK SCAN

PARALLEL

HIGH DUB

NORM DUB

REC

PLAY

REC

PLAY

The search range varies depending on REV MODE switch

settings.

u: Only one side of tape

j

: Both sides of the tape when searching in the same

direction as playback

OR

Only one side of the tape when searching in the opposite

direction as playback

p

: Both sides followed by the first side

(side “A” w

side “B” w side “A” if CPS is started when

the tape’s forward side (facing you) is playing; or side “B”

w

side “A” w side “B” if CPS is started when the tape’s

reverse side (facing away) is playing)

< The CPS function may not work properly if blanks between

songs are less than 4 seconds long or contain noise.

ENGLISH

15

Intro Check

Intro Check plays the first 15 seconds of each song, allowing you

to quickly find the song you are looking for.

Press the INTRO CHECK button during playback or stop. The

tape will fast wind in the same direction as playback. When you

find the desired song, press the INTRO CHECK button again to

start playback.

The Intro Check range varies depending on REV MODE switch

settings:

u

: Checks one side of the tape

j

: Checks both sides of the tape

p

: Checks both sides of tape then double checks the first side

(side “A” w

side “B” w side “A” if Intro Check is started

on the tape’s forward side (facing you); or side “B” w

side

“A” w

side “B” if Intro Check is started on the tape’s

reverse side (facing away)

The tape automatically stops upon completion of the check

operation.

<

Make sure that the TAPE I compartment is empty when

starting Intro Check on TAPE II.

< The tape counter reports how many songs have been intro-

checked so far.

< Activating the Intro Check function during normal playback

will cause it to skip to the next song: playback of the current

song is interrupted midway.

<

The Intro Check function may not work properly if blanks

between songs are less than 4 seconds long or contain noise.

16

Recording (either TAPE I or TAPE II)

13

4

2 2

5 5

8 8A A

67 7

Turn on the power.

Load a tape for recording.

Press the EJECT button (L ) to open the cassette

compartment. Insert the cassette tape with its open edge

facing down, side “A” facing you. Then close the cassette

compartment by pushing in the cassette door until it clicks

shut.

<

If the erasure prevention tabs of the loaded cassette tape

have been broken off, stick a piece of adhesive tape over the

hole(s).

<

With this cassette deck you can use Normal (Type I) and

Chrome (Type II) tapes for recording.

Set the REV MODE switch.

u

: Set to this position to record on one side only.

j

or p: Set to either of these positions to record on both

sides.

Set the DOLBY NR switch.

Set the switch to ON to record with Dolby Noise Reduction.

Set to OFF to record without Dolby Noise Reduction.

4

3

2

1

Press the RECORD button.

The deck enters the record-pause mode. “J” and “ ”

will light on the display.

Adjust the recording level.

Start playback of your recording source and set the REC

LEVEL control knob so that the level meter indicates “0 dB” at

peaks.

Set the recording direction.

Recording is made in the direction indicated by the

play/record direction indicator (h

or y). To change this

direction, press the opposite direction play button (h

or y).

When everything is ready, start recording by pressing

the PAUSE button or the play button whose arrow

points in the same direction as the indicator.

<

To record on both tape sides, set the REV MODE switch to

“j

” or “p” and press the forward play button (y). If

you press the reverse play button (h

), recording will be done

only on side “B”.

<

To stop recording, press the stop button (H).

8

Be careful not to press play button whose arrow points in

the same direction as the indicator. Doing so will start

recording.

7

6

REC

5

Side “A” facing you

ENGLISH

17

Recording (either TAPE I or TAPE II)

To stop recording temporarily

Press the PAUSE button to stop recording temporarily.

A second press of the button resumes recording.

To Erase Recordings

When you make a recording, the tape is overwritten (previous

recording is erased). To erase a tape without making a new

recording, set the REC LEVEL control to the minimum (

∞)

position and press the RECORD button followed by the play

button (h

or y).

Quick Record Start

Hold down the RECORD button and press the play button (h

or y) corresponding to the direction you want the tape to

run.

Recording Silence

Use this function to create blanks between songs for proper

operation of the Computamatic Program Search (CPS)

function.

Press the REC MUTE button when recording reaches the

desired point. No signal is recorded for about 4 seconds and

then the deck enters the record-pause mode. To resume

recording, press the PAUSE button.

To create a blank of more than 4 seconds long

Hold down the REC MUTE button for the desired length of

time. When you release the button, the deck enters the

record-pause mode.

To create a blank of less than 4 seconds long

Press the PAUSE button within 3 seconds of pressing the REC

MUTE button.

< If you press the REC MUTE button when the deck is in the

record-pause mode, no signal is recorded for about 4

seconds, and then the deck shifts back to the record-pause

mode.

18

Mic Mixing Recording

This function allows you to record your voice and another audio

source together on a cassette tape.

<

The mic sound is fed into both the Left and Right channels so

it is located in the center of the stereo image.

< You have the choice of either selecting the audio source you

want on the amplifier connected to the LINE IN jacks of the

deck, or plugging the desired source directly into the deck’s

LINE IN jacks.

<

To prevent feedback (howling), disable the speaker outputs

from the amplifier. Use headphones to monitor recording.

< This cassette deck is not compatible with stereo mics. Always

use a mono mic.

Adjusting Mix Recording Level

To record a mix of voice and another audio source, you need

to adjust the mic input level and then fine tune the overall

recording level.

1. Plug your microphone into the MIC jack on the front panel.

2.Start playing the audio source, switch the deck into the

record-pause mode (by pressing the RECORD button), and

temporarily adjust the REC LEVEL control to a relatively low

level.

3. Speak into the mic and adjust the MIC level control to get the

optimum balance between your voice and the other source.

4.Fine tune the overall recording level using the REC LEVEL

control so that the level meter reads 0 dB at peaks.

5. When everything is ready, start recording as instructed earlier

in this manual.

Audio source

Adjustment of

mic input level

Adjustment of overall

recording level

ENGLISH

19

Continuous Recording

2

3

4

1 1

5

AA

This function allows you to make uninterrupted recordings on

both sides of two tapes.

Load cassette tapes for recording into the TAPE I and

TAPE II compartments.

Set the REV MODE switch to the “p” (CONT PLAY)

position.

<

Set the DOLBY NR switch to the ON position if you want to.

Press the TAPE I deck’s RECORD button.

The deck enters the record-pause mode. “J” and “ ”

will light on the display. Now adjust the recording level and

any other settings, as required.

REC

3

2

1

Check the recording direction.

If an indicator is lit which points in the direction opposite to

the one desired, change the direction by pressing the

opposite direction play button (h

or y).

Recording is done in this order:

You can start recording from side “B” of TAPE I. But if you do

so, side “A” of this tape is not recorded: when recording

reaches the end of side “B”, the TAPE II deck starts recording.

< The TAPE II deck always starts recording from side “A”.

Start recording.

Recording starts when you press the PAUSE button or the

play button whose arrow points in the same direction as the

indicator on the TAPE I deck.

When recording is finished on the TAPE I deck, the TAPE II

deck automatically starts recording.

<

The transition from TAPE I to TAPE II takes several seconds.

To stop recording

Press the stop button (H) of the deck which is currently

recording.

A

5

TAPE I Side “A”

x

Side “B”

x

TAPE II Side “A”

x

Side “B”

Be careful not to press play button whose arrow points in

the same direction as the indicator. Doing so will start

recording.

4

Side “A” facing you

20

Parallel Recording

3

2 2

1 1

This function allows you to record the same material

simultaneously on both TAPE I and TAPE II.

Load tapes into both decks and press the PARALLEL REC

button to start recording.

< Before starting recording, check and correct the following by

performing steps - on page 16.

Record direction, Reverse mode setting, Dolby NR setting,

Recording level, etc.

When everything is ready, get back into stop mode if the

deck is in another mode.

< During parallel recording, the PARALLEL indicator is lit on the

display.

< During parallel recording, only the following buttons work:

TAEP I deck: Stop (H

)

TAPE II deck: PAUSE, REC MUTE, stop (H

)

<

Pressing the stop button (H) on either deck stops both tapes

at once.

71

Insert a cassette tape for playback into the TAPE I

compartment and a cassette tape for recording into the

TAPE II compartment.

Set the tape transport direction on both decks.

If the play/record direction indicator (h or y) on the display

points in the direction opposite to the one desired, press the

PAUSE button followed play button (h

or y) corresponding

to the desired direction.

After changing the tape transport direction, be sure to press

the stop button (H

) to get out of the pause mode.

<

Be careful not to press play button whose arrow points in the

same direction as the indicator. Doing so will start playback.

< Set the REV MODE switch as required.

<

You don’t need to adjust the recording level or set the Dolby

NR system, as both depend on the pre-recorded source tape.

Press either DUB START button to start dubbing.

For normal speed dubbing, press the NORMAL button.

For high-speed dubbing, press the HIGH button.

High-speed dubbing makes a copy at approximately two

times the normal speed. We recommend normal speed

dubbing for best audio quality.

3

2

1

Dubbing (from TAPE I to TAPE II)

La page est en cours de chargement...

TEAC W-865R Manuel utilisateur

TEAC W-865R Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents