Saber Compact R50CC0612 Manuel utilisateur

Printed in China

Estimated assembly time:

45 minutes

08/31/11 • 80020317

PRODUCT GUIDE

MODEL R50CC0612

IMPORTANT: Fill out the product record information below.

Serial Number

Date Purchased

For support and to register your

grill, please visit us at

www.sabergrills.com

If you have questions or need

assistance during assembly,

please call 1-888-94-SABER

1-888-947-2237

Place serial

number label here

?FOR NATURAL GAS CONVERSION:

?NG Conversion Kit Model A00AA0412 must be used. Sold separately.

2

DANGER

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or serious injury.

CAUTION

CAUTION: Indicates a potentially hazardous situation or

unsafe practice which, if not avoided, may result in minor

or moderate injury.

Safety Symbols

The symbols and boxes shown below explain what each

heading means. Read and follow all of the messages found

throughout the manual.

CAUTION:

Read and follow all safety statements, assembly

instructions, and use and care directions before attempting

to assemble and cook.

INSTALLER/ASSEMBLER:

Leave this manual with consumer.

CONSUMER:

Keep this manual for future reference.

WARNING:

Failure to follow all manufacturer’s instructions could result

in serious personal injury and/or property damage.

CAUTION:

Some parts may contain sharp edges – especially as noted

in the manual! Wear protective gloves if necessary.

TABLE OF CONTENTS

For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Use and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Parts Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-17

DANGER

WARNING

CAUTION

For residential use only. Do not use for commercial

cooking.

THIS GRILL IS FOR OUTDOOR USE ONLY.

·If you smell gas:

·Shut off gas to appliance.

·Extinguish any open flame.

·Open lid.

·If odor continues, keep away from the appliance and

immediately call your gas supplier or your fire

department.

·Do not store or use gasoline or other flammable liquids

or vapors in the vicinity of this or any other appliance.

·An LP cylinder not connected for use shall not be

stored in the vicinity of this or any other appliance.

WARNING

CALIFORNIA PROPOSITION 65

1. Combustion by-products produced when using

this product contain chemicals known to the State of

California to cause cancer, birth defects, and other

reproductive harm.

2. This product contains chemicals, including lead

and lead compounds, known to the State of

California to cause cancer, birth defects or other

reproductive harm.

Wash your hands after handling this product.

WARNING

Do not attempt to repair or alter the

hose/valve/regulator for any “assumed” defect. Any

modification to this assembly will void your warranty

and create the risk of a gas leak and fire. Use only

authorized replacement parts supplied by

manufacturer.

Installation Safety Precautions

·Use grill, as purchased, only with LP (propane) gas and

the regulator/valve assembly supplied. A conversion kit

must be purchased for use with natural gas.

·Grill installation must conform with local codes, or in their

absence of local codes, with either the National Fuel Gas

Code, ANSI Z223.1/ NFPA 54, Natural Gas and Propane

Installation Code, CSA B149.1, or Propane Storage and

Handling Code, B149.2, or the Standard for Recreational

Vehicles, ANSI A 119.2/NFPA 1192, and CSA Z240 RV

Series, Recreational Vehicle Code, as applicable.

·All electrical accessories (such as rotisserie) must be

electrically grounded in accordance with local codes, or

National Electrical Code, ANSI / NFPA 70 or Canadian

Electrical Code, CSA C22.1. Keep any electrical cords

and/or fuel supply hoses away from any hot surfaces.

·This grill is safety certified for use in the United States

and/or Canada only. Do not modify for use in any other

location. Modification will result in a safety hazard.

·The pressure regulator and hose assembly supplied must

be used and replacements must be those specified by

appliance manufacturer.

3

DANGER

USE AND CARE

·NEVER store a spare cylinder under or near the

appliance or in an enclosed area.

·Never fill a cylinder beyond 80% full.

·An over filled or improperly stored cylinder is a hazard

due to possible gas release from the safety relief valve.

·If you see, smell or hear gas escaping, immediately get

away from the LP cylinder/appliance and call your fire

department.

·This could cause an intense fire with risk of property

damage, serious injury or death.

LP Cylinder Valve

Retainer Strap

Safety

Cap

LP Cylinder Removal, Transport and Storage

·Turn OFF all control knobs and LP cylinder valve. Turn

coupling nut counterclockwise by hand only - do not use tools

to disconnect. Loosen cylinder screw beneath bottom shelf,

then lift LP cylinder up and out of cart. Install safety cap onto

LP cylinder valve. Always use cap and strap supplied with

valve. Failure to use safety cap as directed may result in

serious personal injury and/or property damage.

·A disconnected LP cylinder in

storage or being

transported must have a safety cap

installed (as shown). Do not store an LP

cylinder in enclosed spaces such as a

carport, garage, porch, covered patio or

other building. Never leave an LP cylinder

inside a vehicle which may become overheated

by the sun.

·Do not store an LP cylinder in an area where children play.

LP Cylinder

The LP cylinder used with your grill must meet the following

requirements:

·Use LP cylinders only with these required measurements: 12”

(30.5cm) (diameter) x 18” (45.7cm) (tall) with 20 lb. (9kg) capacity

maximum.

· LP cylinders must be constructed and marked in accordance with

specifications for LP cylinders of the U. S. Department of

Transportation (DOT) or for Canada, CAN/CSA-B339, cylinders,

spheres and tubes for transportation of dangerous goods.

Transport Canada (TC). See cylinder collar for marking.

·LP cylinder valve must have:

-Type 1 outlet compatible with

regulator or grill.

-Safety relief valve.

-UL listed Overfill Protection

Device (OPD). This OPD safety

feature is identified by a unique triangular hand wheel. Use only

LP cylinders equipped with this type of valve.

·LP cylinder must be arranged for vapor withdrawal and include

collar to protect LP cylinder valve. Always keep LP cylinder in

upright position during use, transit or storage.

OPD Hand Wheel

LP cylinder in upright position for vapor withdrawal

LP (Liquefied Petroleum Gas)

·LP gas is nontoxic, odorless and colorless when produced. For

Your Safety, LP gas has been given an odor (similar to rotten

cabbage) so that it can be smelled.

·LP gas is highly flammable and may ignite unexpectedly when

mixed with air.

LP Cylinder Filling

·Use only licensed and experienced dealers.

·LP dealer must purge new cylinder before filling.

·Dealer should NEVER fill LP cylinder more than 80% of LP

cylinder volume. Volume of propane in cylinder will vary by

temperature.

·A frosty regulator indicates gas overfill. Immediately close LP

cylinder valve and call local LP gas dealer for assistance.

·Do not release liquid propane (LP) gas into the atmosphere.

This is a hazardous practice.

·To remove gas from LP cylinder, contact an LP dealer or call a

local fire department for assistance. Check the telephone

directory under “Gas Companies” for nearest certified LP

dealers.

4

LP Cylinder Exchange

·Many retailers that sell grills offer you the option of replacing your

empty LP cylinder through an exchange service. Use only those

reputable exchange companies that inspect, precision fill, test

and certify their cylinders. Exchange your cylinder only for an

OPD safety feature-equipped cylinder as described in the

“LP Cylinder” section of this manual.

·Always keep new and exchanged LP cylinders in upright position

during use, transit or storage.

·Leak test new and exchanged LP cylinders BEFORE

connecting to grill.

LP Cylinder Leak Test

For your safety

·Leak test must be repeated each time LP cylinder is exchanged

or refilled.

·Do not smoke during leak test.

·Do not use an open flame to check for gas leaks.

·Grill must be leak tested outdoors in a well-ventilated area, away

from ignition sources such as gas fired or electrical appliances.

During leak test, keep grill away from open flames or sparks.

·Use a clean paintbrush and a 50/50 mild soap and water

solution. Brush soapy solution onto areas indicated by arrows in

figure below.

·Do not use household cleaning agents. Damage to gas train

components can result.

If “growing” bubbles appear do not use or move the

LP cylinder. Contact an LP gas supplier or your fire

department!

WARNING

Safety Relief Valve

OPD Hand Wheel

c

k

w

o

l

i

s

C

e

f

O

Strap and Cap

Type 1 outlet with

thread on outside

Connecting Regulator to the LP Cylinder

1. LP cylinder must be properly secured onto grill. (Refer to

assembly section of your grill manual).

2. Turn all control knobs to the OFF position.

3. Turn LP cylinder OFF by turning hand wheel clockwise to a

Full Stop.

4. Remove the protective cap from LP cylinder valve. Always use

cap and strap supplied with valve.

Do not use a POL transport

plug (plastic part with external

threads)! It will defeat the

safety feature of the valve.

5. Hold regulator and insert nipple into LP

cylinder valve. Hand-tighten the

coupling nut, holding regulator in a

straight line with LP cylinder valve so

as not to cross-thread the connection.

Nipple has to be centered

into the LP cylinder valve.

Straight

Hold coupling nut and

regulator as shown for

proper connection to LP

cylinder valve.

Connecting Regulator to the LP Cylinder (Con’t.)

6. Turn the coupling nut clockwise and tighten to a Full Stop.

The regulator will seal on the back-check feature in the LP

cylinder valve, resulting in some resistance. An additional

one-half to three-quarters turn is required to complete the

connection. Tighten by hand only - do not use tools.

NOTE:

If you cannot complete the connection, disconnect regulator and

repeat steps 5 and 6. If you are still unable to complete the

connection, do not use this regulator!

5

WARNING

DANGER

Do not insert any tool or foreign object into the valve outlet

or safety relief valve. You may damage the valve and

cause a leak. Leaking propane may result in explosion,

fire, severe personal injury, or death.

·Outdoor gas appliance is not intended to be installed in

or on a boat.

·Outdoor gas appliance is not intended to be installed in

or on an RV.

·Never attempt to attach this grill to the self-contained LP

gas system of a camper trailer or motor home.

·Do not use grill until leak tested.

·If a leak is detected at any time, STOP and call the fire

department.

·If you cannot stop a gas leak, immediately close LP

cylinder valve and call LP supplier or your fire

department!

6

Leak Testing Valves, Hoses and Regulator

1. Turn all control knobs to the OFF position.

2. Be sure regulator is tightly connected to LP cylinder.

3. Completely open LP cylinder valve by turning hand wheel

counterclockwise. If you hear a rushing sound, turn gas off

immediately. There is a major leak at the connection. Correct

before proceeding.

4. Brush soapy solution onto areas circled below, or other similar

fittings on your grill.

CAUTION

WARNING

Turn controls and gas source or tank OFF when not

in use.

·Putting out grease fires by closing the lid is not

possible. Grills are well ventilated for safety reasons.

·Do not use water on a grease fire. Personal injury may

result. If a grease fire develops, turn knobs and LP

cylinder off.

·Do not leave grill unattended while preheating or

burning off food residue on HI. If grill has not been

regularly cleaned, a grease fire can occur that may

damage the product.

·For Safe Use of Your Grill and to avoid serious injury:

·Do not let children operate or play near grill.

·Keep grill area clear and free from materials that burn.

·Do not block holes in sides or back of grill.

·Check burner flames regularly.

·Use grill only in well-ventilated space. NEVER use in

enclosed space such as carport, garage, porch,

covered patio, or under an overhead structure of any

kind.

·Do not use charcoal or ceramic briquets in a gas grill.

·Use grill at least 3 ft. from any wall or surface.

Maintain 10 ft. clearance to objects that can catch fire or

sources of ignition such as pilot lights on water heaters,

live electrical appliances, etc.

·Apartment Dwellers:

·Check with management to learn the requirements and

fire codes for using an LP gas grill in your apartment

complex. If allowed, use outside on the ground floor

with a three (3) foot clearance from walls or rails. Do

not use on or under balconies.

·NEVER attempt to light burner with lid closed. A build-

up of non-ignited gas inside a closed grill is hazardous.

·Never operate grill with LP cylinder out of correct

position specified in assembly instructions.

·Always close LP cylinder valve and remove coupling nut

before moving LP cylinder from specified operation

position.

WARNING

·Safety Tips

·Before opening LP cylinder valve, check the coupling nut for

tightness.

·When grill is not in use, turn off all control knobs and LP

cylinder valve.

·Never move grill while in operation or still hot.

·Use long handled barbecue utensils and oven mitts to avoid

burns and splatters.

·Maximum load for sideburner and side shelf is 10 lbs.

·The grease tray must be inserted into grill and emptied after

each use. Do not remove grease tray until grill has

completely cooled.

·Clean grill often, preferably after each cookout. If a bristle

brush is used to clean any of the grill cooking surfaces,

ensure no loose bristles remain on cooking surfaces prior to

grilling. It is not recommended to clean cooking surfaces

while grill is hot.

·If you notice grease or other hot material dripping from grill

onto valve, hose or regulator, turn off gas supply at once.

Determine the cause, correct it, then clean and inspect valve,

hose and regulator before continuing. Perform a leak test.

·Keep ventilation openings in cylinder enclosure (grill cart)

free and clear of debris.

·Do not store objects or materials inside the grill cart

enclosure that would block the flow of combustion air to the

underside of either the control panel or the firebox bowl.

·The regulator may make a humming or whistling noise during

operation. This will not affect safety or use of grill.

·If you have a grill problem see the “Troubleshooting Section”.

·If the regulator frosts, turn off grill and LP cylinder valve

immediately. This indicates a problem with the cylinder and

it should not be used on any product. Return to supplier!

Main Burner Ignitor Lighting

Do not lean over grill while lighting.

1. Turn OFF all control knobs.

2. Turn ON gas at LP cylinder.

3. Open lid during lighting.

4. To ignite, push and turn burner control knob to HI.

5. Push and hold ELECTRONIC IGNITION button until the burner

lights (use flame viewing ports to verify).

6. If ignition does NOT occur in 5 seconds, turn the control knobs

OFF, wait 5 minutes, and repeat the lighting procedure.

7. Ignite remaining burners by repeating steps 4 through 6 for

each burner.

8. Once each burner has ignited, turn control knobs to desired

setting.

7

CAUTION

If ignition does NOT occur in 5 seconds, turn the

control knobs OFF, wait 5 minutes and repeat the

lighting procedure. If the burner does not ignite with

the valve open, gas will continue to flow out of the

burner and could accidently ignite with risk of injury.

Main Burner Match-Lighting

Do not lean over grill while lighting.

1. Open lid. Turn ON gas at LP cylinder.

2. Place match into match holder (hanging from left side of

cabinet). Light match; then light burner by placing match

through the match light hole on left side of grill.

3. Push in and turn left control knob to the HI position. Once

burner has ignited (use flame viewing port to verify) turn

control knob to desired setting.

4. If ignition does not occur in 5 seconds, turn the burner control

knob OFF, wait 5 minutes, and repeat the lighting procedure.

5. Light adjacent burners in sequence by pushing control knobs

in and turning to the HI position.

Burner Flame Check

·Remove cooking grates and emitters. Light burners, rotate

knobs from HI to LO. You should see a smaller flame in LO

position than seen on HI. Perform burner flame check on side

burner, also. Always check flame prior to each use. If only low

flame is seen refer to “Sudden drop or low flame” in the

Troubleshooting Section.

Turning Grill Off

·Turn all control knobs to OFF position. Turn LP cylinder OFF by

turning hand-wheel clockwise to a full stop.

Ignitor Check

·Turn Gas OFF at LP cylinder. Press and hold electronic

ignition button. “Click” should be heard and spark seen each

time between collector box or burner and electrode. See

“Troubleshooting” if no click or spark.

HI

LO

Viewing ports

8

Valve Check

·IMPORTANT: Make sure gas is OFF at LP cylinder before

checking valves. Knobs lock in OFF position. To check valves,

first push in control knobs and release, control knobs should spring

back. If control knobs do not spring back, replace valve assembly

before using grill. Turn control knobs to LO position then turn back

to OFF position. Valves should turn smoothly.

Hose Check

·Before each use, check to see if hoses are cut or worn. Replace

damaged hoses before using grill. Use only valve/hose/regulator

specified by manufacturer.

Storing your grill

·Clean cooking grates.

·Store in dry place.

·When LP cylinder is connected to grill, store outdoors in a

well ventilated space and out of reach of children.

·Cover grill if stored outdoors. Choose from a cover offered

by the manufacturer.

·Store grill indoors ONLY if LP cylinder is turned off and

disconnected, removed from grill and stored outdoors.

·When removing grill from storage, follow “Cleaning the

Burner Assembly” instructions before starting grill.

Quick Start Tips

Preheating for different types of grilling:

·Sear - preheat with all burners set to HI for maximum cooking

grate temperatures

·Barbecue - preheat with all burners set to LO for a lower starting

grate temperature for grilling foods slower.

·Indirect grilling - preheat one burner only on the side opposite

where the food will be placed to allow the slowest and lowest

grilling for larger cuts of meat.

·Roasting - place the warming rack on the lower supports and

use burner(s) directly under the food on LO or indirectly for lower

temperature cooking. This will allow more heat to circulate

around the food during grilling.

Lowering the temperature of the cooking grate:

·Control knob - turn the control knob to the LO setting for the

lowest temperature setting.

·Control knob - for the lowest cooking grate temperatures the

food can be grilled indirectly with the burner under the food in

the OFF position and a single burner away from the food on LO.

·During grilling the grill can be cooled down faster by lifting the lid

while adjusting the control knobs to a low setting.

Adding a smoked flavor while grilling:

·Do not use wood chunks on a Saber grill cooking grate.

·Wood chips can be used by placing them between the cooking

grate bars. Soaking the wood chips for a minimum of 15

minutes prior to use will extend the smoking time.

·A smoker box (sold separately) box can be used by filling it with

wood chips and placing it directly on the cooking grate with the

burner on the HI or LO setting.

General Grill Cleaning

Do not mistake brown or black accumulation of grease and smoke

for paint. Apply a strong solution of detergent and water or use a grill

cleaner with scrub brush on insides of grill lid and bottom. Rinse and

allow to completely air dry.

Do not apply a caustic grill/oven cleaner to painted surfaces.

·Plastic parts: Wash with warm soapy water and wipe dry.

Do not use citrisol, abrasive cleaners, degreasers or a

concentrated grill cleaner on plastic parts. Damage to and

failure of parts can result.

·Porcelain surfaces: Because of glass-like composition,

most residue can be wiped away with baking soda/water solution

or specially formulated cleaner. Use non-abrasive scouring

powder on stubborn stains.

·Painted surfaces: Wash with mild detergent or non-abrasive

cleaner and warm soapy water. Wipe dry with a soft non-

abrasive cloth.

·Stainless steel surfaces: To maintain your grill’s high quality

appearance, wash with mild detergent and warm soapy water

and wipe dry with a soft cloth after each use. Baked-on

grease deposits may require the use of an abrasive plastic

cleaning pad. Use only in direction of brushed finish to avoid

damage. Do not use abrasive pad on areas with graphics.

Cooking surfaces: If a bristle brush is used to clean any of the

grill cooking surfaces, ensure no loose bristles remain on cooking

surfaces prior to grilling. It is not recommended to clean cooking

surfaces while grill is hot.

9

Cleaning the Burner Assembly

Follow these instructions to clean and/or replace parts of burner

assembly or if you have trouble igniting grill.

1. Turn gas OFF at control knobs and LP cylinder.

2. Remove cooking grates and emitters.

3. Remove carryover tubes.

4. Detach electrode from burner.

5. Carefully lift each burner up and away from valve openings.

We suggest three ways to clean the burner tubes. Use the one

easiest for you.

A. Bend a stiff wire (a light weight coat hanger works well)

into a small hook. Run the hook through each burner

several times.

B. Use a narrow bottle brush with a flexible handle (do not

use a brass wire brush), run the brush through each

burner tube several times.

C. Wear eye protection: Use an air hose to force air into the

burner tube and out the burner ports. Check each port to

make sure air comes out each hole.

7. Wire brush entire outer surface of burner to remove food

residue and dirt.

8. Clean any blocked ports with a stiff wire such as an open paper

clip.

9. Check burner for damage, due to normal wear and corrosion

some holes may become enlarged. If any large cracks or holes

are found replace burner.

VERY IMPORTANT: Burner tubes must re-engage valve

openings. See illustration below.

10. Attach electrode to burner.

11. Carefully replace burners.

12. Attach burners to brackets on firebox.

13. Reposition carryover tubes and attach to burners. Replace

emitters and cooking grates.

Firebox

Carryover tube

Firebox burner

bracket

Pry off

electrode with

a flat blade

screwdriver

Electrode

Correct

burner-to-valve

engagement

CONTROL PANEL

VALVE

SPIDER WEBS

BURNER

INSIDE BURNER

CONTROL PANEL

CAUTION

SPIDER ALERT!

SPIDER AND WEBS

INSIDE BURNER TUBE

If you notice that your grill is getting hard to light or that the

flame isn’t as strong as it should be, take the time to check and

clean the burners.

In some areas of the country, spiders or small insects have been

known to create “flashback” problems. The spiders spin webs, build

nests and lay eggs in the grill’s burners tubes(s) obstructing the flow

of gas. The backed-up gas can ignite behind the control panel. This

is known as a flashback and it can damage your grill and even cause

injury.

To prevent flashbacks and ensure good performance the burner

should be removed from the grill and cleaned before use whenever

the grill has been idle for an extended period.

10

LIMITED LIFETIME WARRANTY:

Saber warrants the fabricated stainless steel components (lids, lid inserts, exterior fire box and cart panels), to be free from defects in

material and workmanship under normal residential use for the lifetime of the product.

Saber’s Limited Lifetime Warranty covers the structural integrity of the lids, lid inserts, exterior firebox and cart panels. Should

structural deterioration occur to the degree of non performance, the part(s) will be replaced, free of change to the consumer for

installation. Costs associated with the installation of replacement warranty parts is not covered by this limited lifetime warranty and is

the sole responsibility of the owner.

This warranty excludes discoloration, surface scratches, weather and atmospheric related staining, and minor surface rust and

oxidation which are normal conditions and to be expected with any outdoor product.

TEN YEAR LIMITED WARRANTY: Saber warrants the stainless steel burner tubes and carryover tubes to be free from defects in

materials and workmanship under normal residential use for a period of ten (10) years from the original date of purchase. The part will

be replaced, free of charge.

FIVE YEAR LIMITED WARRANTY: Saber warrants the stainless steel cooking grates, emitters, warming racks and porcelain

enameled warming racks, grates, and burner boxes to be free from defects in materials and workmanship under normal residential use

for a period of five (5) years from the original date of purchase. The part will be replaced free of charge.

TWO YEAR FULL WARRANTY: Saber warrants all painted parts and any other parts not specifically mentioned above, to be free from

defects in materials and workmanship under normal residential use for a period of two (2) years from the original date of purchase.

Saber will replace the part which fails or is found to be defective during the warranty period, at no cost to the original purchaser.

Owner shall be responsible for proper installation, providing normal care and maintenance, and providing proof of purchase upon

request.

Saber reserves the right, PRIOR to shipping warranty replacement parts, to require the part in question be returned for inspection and

analysis. Requested parts should be returned to Saber, freight pre-paid by the consumer.

WARRANTY LIMITATIONS & EXCLUSIONS

This warranty excludes units purchased for use in all types of commercial and or community use locations such

as restaurants, hotels, catering operations food service establishments, condominium/apartment complexes,

rental properties, and to products with altered or removed serial numbers.

This warranty shall apply ONLY to the products purchased and located in the continental United States and Canada.

Item Warranty Term

Stainless Steel Parts

Lids & Lid inserts Limited Lifetime

Exterior Firebox & Cart Panels Limited Lifetime

Burner Tubes & Carryover Tubes 10 Years

Cooking Grates, Emitters, Warming Racks 5 Years no rust through or burn through

Porcelain Enameled Parts

Lid Insert Limited Lifetime (excludes fading)

Interior Firebox Limited Lifetime no rust through or burn

through (excludes fading)

Warming Racks, Grates, Burner Boxes 5 Years no rust through or burn through

(excludes fading)

Painted Parts 2 Years (excludes fading)

All Other Parts 2 Years

11

The warranty coverage begins on the original date of purchase and proof of date of purchase is required for warranty service. Please

register your product and retain your original sales receipt.

In order to activate the warranty, we require that you send in the attached warranty registration card or register your product online.

This warranty applies only to the original grill owner and cannot/may not be transferred.

This warranty does not apply to damages resulting from negligence, alteration, misuse, abuse, accident, natural disaster, loss of

electrical power to the product for any reason, improper installation or improper operation, unauthorized adjustments or calibrations,

dings, dents, scratches, or damages due to harsh cleaning chemicals.

Saber shall not be liable for incidental, consequential, special or contingent damages resulting from its breach of this written warranty or

any implied warranty.

In the event of any warranty replacement, all removal, replacement and installation are the responsibility of the grill owner.

Saber reserves the right to replace any defective product with a product equal in value to the original purchase price. Warranty repair

or replacement is at the sole discretion of Saber.

Dealers and Distributors may not, under any circumstances, adjust, alter or extend the conditions and terms of the original warranty.

Your Saber warranty does not cover the following:

?Labor charges related to installation or set-up, diagnosis of a problem, or repairs.

?Normal recommended routine maintenance and care.

?Damage resulting from accident, alteration, misuse, abuse, hostile environments, improper installation, or installation not in

accordance with local, state and federal codes and regulations.

?The use of unauthorized or “universal” parts.

?Damage or corrosion caused by lack of maintenance, neglect in following the manufacturer’s care and usage instructions,

grease fires, animals and insects.

?Any damage resulting from the commercial and or community use of this product.

?Retail display models are generally sold “AS IS.” If you have purchased a display model, please be advised that it is sold “AS

IS” and that it is subject to the following warranty exclusions:

?Any exterior or cosmetic damage is non-warrantable

? Any missing components will be replaced at the consumer’s sole expense.

DISCLAIMER OF IMPLIED WARRANTIES AND LIMITATION OF REMEDIES

CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR

REPLACEMENT AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED OR LIMITED TO ONE YEAR OR THE SHORTEST

PERIOD ALLOWED BY LAW. SABER SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

SOME STATES OR PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUETIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTY OF MERCHANTIBILITY

OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU

SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH CAN VARY FROM STATE TO STATE

OR PROVINCE TO PROVINCE.

12

How to Obtain Warranty Service or Repair Parts:

Prior to contacting your dealer or calling us directly, please make sure your grill is registered. You can register your grill at:

http://www.sabergrills.com/registration.

Call your authorized Saber dealer. A list of Saber dealers and their contact information can be found at http://www.sabergrills.com.

Utilize our online customer service at http://www.sabergrills.com/warranty service.

Call Saber directly at 1-(888)-94S-ABER (947-2237). We look forward to assisting you!

Or write us at: Saber

Warranty Service

P. O. Box 1977

Columbus, GA. 31902

Please be prepared to furnish the following information: Purchaser’s name, model and serial number of the grill, date of purchase

and the accurate description of the problem.

Date of Purchase:

Dealer Where You Purchased Your Grill:

Dealer Phone Number:

Model Number:

(located on the cover of your instruction manual or rating label)

Serial Number:

(located on the cover of your instruction manual or rating label)

®

13

Key Qty. Description

A 1 KIT, Door, W/Handle Assembly, (SET of 2)

B 1 KIT, Handle, F/Door, (SET of 2)

C 1 KIT, Front Cabinet Assembly

D 1 KIT, Ignition Module

E 1 KIT, Ignition Wires

F 3 KIT, Electrode, F/Main Burner, W/Wire

G 1 KIT, Rear Cabinet Assembly

H 1 Grommet, F/NG Conversion Hose Hole

I 1 KIT, Bottom Shelf Assembly

J 1 KIT, Tank Retainer Screw

K 4 Caster, Locking

L 1 KIT, Lid Assembly

M 1 KIT, Lid Handle

N 1 KIT, Temperature Gauge, F/Lid

O 1 KIT, Lid Stop, Silicone, (SET of 4)

P 1 KIT, Firebox Assembly

Q 1 KIT, Control Console, W/HVR Assembly and Ignition Switch

R 1 KIT, Ignition Switch Module, W/Wires

S 3 KIT, Control Knob, W/Bezel

T 1 Grease Tray Assembly

U 3 KIT, Burner Box, W/Burner, Carryover and Electrode

V 3 KIT, Cooking Grate, W/Emitter

W 1 Warming Rack

X 1 KIT, Right Side Shelf Assembly, W/Tool Holders

Y 1 KIT, Left Side Shelf Assembly

Z 1 KIT, Tank Exclusion Shelf

AA 1 KIT, Cabinet Connector, (SET of 4)

BB 1 Match Holder, W/Chain

CC 3 KIT, Burner, W/Carryover

DD 3 KIT, Firebox Heat Shield

EE 1 KIT, Lid Shoulder Bolt, (SET of 2)

Not Pictured

. . . 1 Hardware Pack

. . . 1 Grate Cleaning Tool

. . . 1 Assembly Guide, English/Spanish/French

. . . 1 Care and Use Guide, English/Spanish/French

. . . 1 Grilling Guide, English/Spanish/French

PARTS LIST

14

Q

M

C

J

H

AA

K

T

BB

O

S

B

R

A

F

E

I

G

Z

U

P

Y

X

L

N

DD

V

D

PARTS DIAGRAM

EE

CC

W

15

EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department.

Emergencies

Problem

Possible Cause

GAS ISSUES:

Prevention/Solution

Troubleshooting

EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department.

Gas leaking from

cracked/cut/burned

hose.

Gas leaking from LP

cylinder.

Gas leaking from LP

cylinder valve.

Gas leaking between

LP cylinder and

regulator connection.

Fire coming through

control panel.

Grease fire or

continuous excessive

flames above cooking

surface.

Damaged Hose.

Mechanical failure due to rusting or

mishandling.

Failure of cylinder valve from mishandling

or mechanical failure.

Improper installation, connection not tight,

failure of rubber seal.

Fire in burner tube section of burner due to

blockage.

Too much grease buildup in burner area.

Turn OFF gas at LP cylinder. If anything got burned, replace

valve/hose/regulator. If burned, discontinue use of product until a

plumber has investigated cause and corrections are made.

Replace LP cylinder.

Turn OFF LP cylinder valve. Return LP cylinder to gas supplier.

Turn OFF LP cylinder valve. Remove regulator from cylinder and

visually inspect rubber seal for damage. See LP Cylinder Leak Test

and Connecting Regulator to the LP Cylinder.

Turn OFF control knobs and LP cylinder valve. Leave lid open to

allow flames to die down. After fire is out and grill is cold, remove

burner and inspect for spider nests or rust. See Natural Hazard and

Cleaning the Burner Assembly pages.

Turn OFF control knobs and LP cylinder valve. Leave lid open to

allow flames to die down. After cooling, clean food particles and

excess grease from inside firebox area, grease tray and other

surfaces.

Burner(s) will not light

using ignitor. See

Electronic Ignition

Troubleshooting also.)

Continued on next

page.

Trying to light wrong burner.

Burner not engaged with control valve.

Obstruction in burner.

No gas flow.

Vapor lock at coupling nut to LP cylinder.

Coupling nut and LP cylinder valve not fully

connected.

See instructions on door panel and in Use and Care section.

Make sure valves are positioned inside of burner tubes.

Ensure burner tubes are not obstructed with spider webs or other

matter. See cleaning section of Use and Care.

Make sure LP cylinder is not empty. If LP cylinder is not empty, refer

to “Sudden drop in Gas Flow.”

Turn OFF knobs and disconnect coupling nut from LP cylinder. Wait

30 seconds, reconnect and retry.

Turn the coupling nut approximately one-half to three-quarters

additional turn until solid stop. Tighten by hand only-do not use tools.

ELECTRICAL ISSUES:

Electrode cracked or broken; “sparks at

crack.”

Electrode tip not in proper position.

Wire and/or electrode covered with cooking

residue.

Replace electrode(s).

Tip of electrode should be pointing toward gas port opening on

burner. The distance should be 1/8” to 1/4”. Adjust if necessary.

Clean wire and/or electrode with rubbing alcohol and clean swab.

16

Problem Possible Cause

ELECTRICAL ISSUES CON’T.:

Prevention/Solution

Troubleshooting (continued)

Burner(s) will not light

using ignitor. (See

Electronic Ignition

Troubleshooting also).

Continued.

Burner(s) will not match

light.

Sudden drop in gas

flow or low flame.

Flames blow out.

Flare-up.

Persistent grease fire

Flashback (fire in

burner tube(s)).

Unable to fill LP tank.

One burner does not

light from other

burner(s).

Wires are loose or disconnected.

Wires are shorting (sparking) between

ignitor and electrode.

Dead battery.

No spark, no ignition noise.

No spark, some ignition noise.

Sparks, but not at electrode or at full

strength.

See “GAS ISSUES:” on previous page.

Match will not reach

Improper method of match-lighting.

Out of gas.

Excess flow valve tripped.

Vapor lock at coupling nut/LP tank

connection.

High or gusting winds

Low on LP gas.

Excess flow valve tripped.

Grease buildup.

Excessive fat in meat.

Excessive cooking temperature.

Grease trapped by food buildup around

burner system.

Burner and/or burner tubes are blocked.

Some dealers have older fill nozzles with

worn threads.

Grease buildup or food particles in end(s)of

carryover tube(s).

Reconnect wires or replace electrode/wire assembly.

Replace ignitor wire/electrode assembly.

Replace with a new alkaline battery.

See Section l of Electronic Ignition System.

See Section ll of Electronic Ignition System.

See Section lll of Electronic Ignition System.

Use long-stem match (fireplace match)

See “Match-Lighting” section of Use and Care.

Check for gas in LP tank.

Turn off knobs, wait 30 seconds and light grill. If flames are still low,

turn off knobs and LP tank valve. Disconnect regulator. Reconnect

regulator and leak-test. Turn on LP tank valve, wait 30 seconds and

then light grill.

Turn off knobs and LP tank valve. Disconnect coupling nut from tank.

Reconnect and retry.

Turn front of grill to face wind or increase flame height.

Refill LP tank.

Refer to “Sudden drop in gas flow” above.

Clean burners and inside of grill/firebox.

Trim fat from meat before grilling.

Adjust (lower) temperature accordingly.

Turn knobs to OFF. Turn gas off at LP tank. Leave lid in position and

let fire burn out. After grill cools, remove and clean parts.

Turn knobs to OFF. Clean burner and/or burner tubes. See burner

cleaning section of Use and Care manual.

The worn nozzles don’t have enough “bite” to engage valve. Try a

second LP dealer.

Clean carryover tube(s) with a wire brush.

ELECTRONIC IGNITION:

17

Troubleshooting - Electronic Ignition

No sparks appear at

any electrodes when

Electronic Ignition

Button is pressed; no

noise can be heard

from spark module.

No sparks appear at

any electrodes when

Electronic Ignition

Button is pressed;

noise can be heard

from spark module.

Sparks are present but

not at all electrodes

and/or not at full

strength.

Problem (Ignition) Possible Cause Check Procedure Prevention/Solution

SECTION l

Battery not installed

properly.

Dead battery.

Button assembly not

installed properly.

Faulty spark module.

Switch wires

disconnected.

Output lead connections

not connected.

Output lead connections

not connected.

Arcing to grill away from

burner(s).

Weak battery.

Electrodes are wet.

Electrodes cracked or

broken “sparks at crack”.

SECTION ll

SECTION lll

Check battery orientation.

Has battery been used

previously?

Check to ensure threads are

properly engaged. Button

should travel up and down

without binding.

If no sparks are generated with

new battery and good wire

connections, module is faulty.

Check to ensure switch wires

are connected.

Are output connections on and

Tight?

Are output connections on and

tight?

If possible, observe grill in dark

location. Operate ignition

system and look for arcing

between output wires and grill

frame.

All sparks present but weak or

at slow rate.

Has moisture accumulated on

electrode and/or in burner

ports?

Inspect electrodes for cracks.

Install battery (make sure that “+” and “-”

connectors are oriented correctly, with “+” end up

and “-” end down.

Replace battery with new alkaline battery.

Remove battery cap and reinstall, making sure it

can be fully engaged.

Replace spark module.

Reconnect switch wires.

Remove and reconnect all output connections at

module and electrodes.

Remove and reconnect all output connections at

module and electrodes.

If sparks are observed other than from burner(s),

wire insulation may be damaged. Replace wires.

Replace battery with a new alkaline battery.

Use paper towel to remove moisture.

Replace cracked or broken electrodes.

18

NOTES

19

NOTES

20

La page charge ...

Saber Compact R50CC0612 Manuel utilisateur

Ce manuel convient également à

Saber Compact R50CC0612 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents