STIHL MS 441 C Manuel utilisateur

Instruction Manual

Notice d’emploi

STIH)

STIHL MS 441

BA_U1_82_01.fm Seite 0 Mittwoch, 12. April 2006 4:21 16

1MS 441

English

BA_SE_187_003_01_01.fmPrinted on chlorine-free paper.

Printing inks contain vegetable oils; paper can be recycled.

0458 219 8221 A. M0,75. E6. Fi. Printed in Germany

STIHl

Contents

Guide to Using this Manual .............. 2

Safety Precautions and Working

Techniques ....................................... 3

Mounting the Bar and Chain ........... 25

Tensioning the Saw Chain ............. 27

Checking Chain Tension ................. 27

Fuel ................................................ 27

Fueling ............................................ 28

Chain Lubricant .............................. 30

Filling Chain Oil Tank ..................... 30

Checking Chain Lubrication ........... 31

Chain Brake .................................... 31

Winter Operation ............................ 32

Electric Handle Heating .................. 33

Information Before You Start .......... 34

Starting / Stopping the Engine ........ 34

Operating Instructions .................... 37

Oil Quantity Control ........................ 38

Taking Care of Guide Bar ............... 39

Air Filter System ............................. 40

Removing the Air Filter ................... 40

Cleaning Standard Filter ................. 41

Cleaning HD Filter .......................... 41

Motor Management ........................ 42

Adjusting the Carburetor ................ 42

Spark Arresting Screen

in Muffler ......................................... 44

Checking the Spark Plug ................ 44

Replacing Starter Rope

and Rewind Spring ......................... 45

Storing the Machine ........................ 48

Checking and Replacing

Chain Sprocket ............................... 48

Maintaining and Sharpening

Saw Chain ...................................... 50

Maintenance Chart ......................... 54

Main Parts of the Saw .................... 56

Specifications ................................. 58

Special Accessories ....................... 59

Ordering Spare Parts ..................... 59

Maintenance and Repairs .............. 59

Key to Symbols .............................. 60

STIHL Limited Emission Control

Warranty Statement ........................ 61

CSA-Standard Z62.3-M1996 .......... 63

Allow only persons who understand this

Manual to operate your chainsaw.

To receive maximum performance and

satisfaction from your STIHL chainsaw,

it is important that you read and

understand

the maintenance and safety

precautions,

starting on page 3, before

using your chainsaw.

Contact your STIHL dealer or the STIHL

distributor for your area if you do not

understand any of the instructions in this

Manual.

!Warning!

Because a chainsaw is a high-speed

wood-cutting tool, some special safety

precautions must be observed as with

any other power saw to reduce the risk

of personal injury.

Careless or improper use may cause

serious or even fatal injury.

STIHL's philosophy is to continually

improve all of its products. As a result,

engineering changes and improvements

are made from time-to-time. If the

operating characteristics or the

appearance of your chainsaw differs

from those described in this Manual,

please contact your STIHL dealer for

information and assistance.

2

English

MS 441

Pictograms

All the pictograms attached to the

machine are shown and explained in

this manual.

The operating and handling instructions

are supported by illustrations.

Symbols in text

The individual steps or procedures

described in the manual may be marked

in different ways:

: A bullet marks a step or procedure

without direct reference to an

illustration.

A description of a step or procedure that

refers directly to an illustration may

contain item numbers that appear in the

illustration.

Example:

Loosen the screw (1)

Lever (2) ...

In addition to the operating instructions,

this manual may contain paragraphs

that require your special attention. Such

paragraphs are marked with the

symbols described below:

Warning where there is a risk of an

accident or personal injury or

serious damage to property.

Caution where there is a risk of

damaging the machine or its

individual components.

Note or hint which is not essential

for using the machine, but may

improve the operator’s under-

standing of the situation and result

in better use of the machine.

Note or hint on correct procedure in

order to avoid damage to the

environment.

Equipment and features

This instruction manual may refer to

several models with different

features. Components that are not

installed on all models and related

applications are marked with an

asterisk (*). Such components may

be available as special accessories

from your STIHL dealer.

Engineering improvements

STIHL’s philosophy is to continually

improve all of its products. As a result,

engineering changes and improvements

are made from time to time. If the

operating characteristics or the

appearance of your machine differ from

those described in this manual, please

contact your STIHL dealer for

assistance.

Therefore some changes, modifications

and improvements may not be covered

in this manual.

Guide to Using this Manual

3MS 441

English

Because a chainsaw is a

high-speed, fast-cutting

power tool, special safety

precautions must be

observed to reduce the

risk of personal injury.

It is important that you

read, fully understand and

observe the following

safety precautions and

warnings. Read the

instruction manual and

the safety instructions periodically.

Careless or improper use may cause

serious or fatal injury.

!Warning!

Reactive forces, including kickback, can

be dangerous. Pay special attention to

the section on reactive forces.

Have your STIHL dealer show you how

to operate your power tool. All safety

precautions that are generally observed

when working with an axe or a hand saw

also apply to the operation of chainsaws.

Observe all applicable federal, state and

local safety regulations, standards and

ordinances.

!Warning!

Do not lend or rent your power tool

without the instruction manual. Be sure

that anyone using it understands the

information contained in this manual.

!Warning!

The use of this machine may be

hazardous.The saw chain has many

sharp cutters. If the cutters contact your

flesh, they will cut you, even if the chain

is not moving. At full throttle, the chain

speed can reach 30 m/s.

Use your chainsaw only for cutting

wooden objects. It must not be used for

any other purposes, since such misuse

may result in an accident or damage to

the machine.

!Warning!

Minors should never be allowed to use

this power tool. Bystanders, especially

children, and animals should not be

allowed in the area where it is in use.

!Warning!

To reduce the risk of injury to bystanders

and damage to property, never let your

power tool run unattended. When it is

not in use (e.g. during a work break),

shut it off and make sure that

unauthorized persons do not use it.

Most of these safety precautions and

warnings apply to the use of all STIHL

chainsaws. Different models may have

different parts and controls. See the

appropriate section of your instruction

manual for a description of the controls

and the function of the parts of your

model.

Safe use of a chainsaw involves

1. the operator

2. the saw

3. the use of the saw.

THE OPERATOR

Physical Condition

You must be in good physical condition

and mental health and not under the

influence of any substance (drugs,

alcohol, etc.) which might impair vision,

dexterity or judgment. Do not operate

this machine when you are fatigued.

!Warning!

Be alert – if you get tired, take a break.

Tiredness may result in loss of control.

Working with any power tool can be

strenuous. If you have any condition that

might be aggravated by strenuous work,

check with your doctor before operating

this machine.

Safety Precautions and

Working Techniques

4

English

MS 441

!Warning!

Prolonged use of a power tool (or other

machines) exposing the operator to

vibrations may produce whitefinger

disease (Raynaud's phenomenon) or

carpal tunnel syndrome.

These conditions reduce the hand's

ability to feel and regulate temperature,

produce numbness and burning

sensations and may cause nerve and

circulation damage and tissue necrosis.

All factors which contribute to white-

finger disease are not known, but cold

weather, smoking and diseases or

physical conditions that affect blood

vessels and blood transport, as well as

high vibration levels and long periods of

exposure to vibration are mentioned as

factors in the development of whitefinger

disease. In order to reduce the risk of

whitefinger disease and carpal tunnel

syndrome, please note the following:

– Most STIHL power tools are

available with an anti-vibration

(“AV”) system designed to reduce

the transmission of vibrations

created by the machine to the

operator's hands. An AV system is

recommended for those persons

using power tools on a regular or

sustained basis.

– Wear gloves and keep your hands

warm. Heated handles, which are

available on some STIHL power-

heads, are recommended for cold

weather use.

– Keep the AV system well

maintained. A power tool with loose

components or with damaged or

worn AV buffers will tend to have

higher vibration levels.

Keep the saw chain sharp. A dull

chain will increase cutting time, and

pressing a dull chain through wood

will increase the vibrations

transmitted to your hands.

– Maintain a firm grip at all times, but

do not squeeze the handles with

constant, excessive pressure. Take

frequent breaks.

All the above-mentioned precautions do

not guarantee that you will not sustain

whitefinger disease or carpal tunnel

syndrome. Therefore, continual and

regular users should closely monitor the

condition of their hands and fingers. If

any of the above symptoms appear,

seek medical advice immediately.

!Warning!

The ignition system of the STIHL unit

produces an electromagnetic field of a

very low intensity. This field may

interfere with some pacemakers. To

reduce the risk of serious or fatal injury,

persons with a pacemaker should

consult their physician and the

pacemaker manufacturer before

operating this tool.

Proper Clothing

!Warning!

To reduce the risk of injury, the operator

should wear proper protective apparel.

Clothing must be sturdy

and snug-fitting, but allow

complete freedom of

movement. Wear long

pants made of heavy

material to help protect

your legs from contact with branches or

brush. To reduce the risk of cut injuries,

wear pants or chaps that contain pads of

cut retardant material.

Avoid loose-fitting jackets, scarfs,

neckties, jewelry, flared or cuffed pants,

unconfined long hair or anything that

could become caught on branches,

brush or the moving parts of the unit.

Secure hair so it is above shoulder level.

Good footing is very

important. Wear sturdy

boots with nonslip soles.

Steel-toed safety boots

are recommended.

5MS 441

English

!Warning!

Wear an approved safety

hard hat to reduce the risk

of injury to your head.

Chainsaw noise may

damage your hearing.

Wear sound barriers (ear

plugs or ear mufflers) to help protect

your hearing. Continual and regular

users should have their hearing checked

regularly.

Be particularly alert and cautious when

wearing hearing protection because

your ability to hear warnings (shouts,

alarms, etc.) is restricted.

Never operate your power tool unless

wearing goggles or properly fitted

protective glasses with adequate top

and side protection complying with your

applicable national standard. To reduce

the risk of injury to your face STIHL

recommends that you also wear a face

shield or face screen over your goggles

or protective glasses.

Always wear gloves when

handling the machine and

the cutting tool. Heavy-

duty, nonslip gloves

improve your grip and

help to protect your

hands.

STIHL offers a wide range of protective

clothing and equipment.

THE POWER TOOL

For illustrations and definitions of the

power tool parts see the chapter on

“Main Parts and Controls.”

!Warning!

Never modify this power tool in any way.

Only attachments supplied by STIHL or

expressly approved by STIHL for use

with the specific STIHL model are

authorized. Although certain

unauthorized attachments are useable

with STIHL power tools, their use may, in

fact, be extremely dangerous.

If this tool is subjected to unusually high

loads for which it was not designed (e.g.

heavy impact or a fall), always check

that it is in good condition before

continuing work. Check in particular that

the fuel system is tight (no leaks) and

that the controls and safety devices are

working properly. Do not continue

operating this machine if it is damaged.

In case of doubt, have it checked by your

STIHL servicing dealer.

THE USE OF THE POWER TOOL

Transporting the Power Tool

!Warning!

To reduce the risk of injury from saw

chain contact, never carry or transport

your power tool with the saw chain

moving. Always engage the chain brake

when taking more than a few steps.

!Warning!

Always switch off the engine, and fit the

chain guard (scabbard) over the chain

and guide bar before transporting the

power tool over longer distances. When

transporting it in a vehicle, properly

secure it to prevent turnover, fuel

spillage and damage to the unit.

It may be carried only in a horizontal

position. Grip the front handle in a

manner that the machine is balanced

horizontally. Keep the hot muffler away

from your body and the cutting

attachment behind you.

001BA115 KN

6

English

MS 441

Fuel

Your STIHL power tool uses an oil-

gasoline mixture for fuel (see the chap-

ter on “Fuel” of your instruction manual).

!Warning!

Gasoline is an extremely

flammable fuel. If spilled

and ignited by a spark or

other ignition source, it

can cause fire and serious

burn injury or property

damage. Use extreme caution when

handling gasoline or fuel mix.

Do not smoke or bring any fire or flame

near the fuel or the power tool. Note that

combustible fuel vapor may escape from

the fuel system.

Fueling Instructions

!Warning!

Fuel your power tool in well-ventilated

areas, outdoors. Always shut off the

engine and allow it to cool before

refueling. Gasoline vapor pressure may

build up inside the fuel tank depending

on the fuel used, the weather conditions

and the tank venting system.

In order to reduce the risk of burns and

other personal injury from escaping gas

vapor and fumes, remove the fuel filler

cap on your power tool carefully so as to

allow any pressure build-up in the tank

to release slowly. Never remove the fuel

filler cap while the engine is running.

Select bare ground for fueling and move

at least 10 feet (3 m) from the fueling

spot before starting the engine. Wipe off

any spilled fuel before starting your

machine.

!Warning!

Check for fuel leakage while refueling

and during operation. If fuel leakage is

found, do not start or run the engine until

the leak is fixed and any spilled fuel has

been wiped away. Take care not to get

fuel on your clothing. If this happens,

change your clothing immediately.

Different models may be equipped with

different fuel caps.

Cap with grip

!Warning!

In order to reduce the risk of fuel spillage

and fire from an improperly tightened

fuel cap, correctly position and tighten

the fuel cap in the fuel tank opening.

To do this with this STIHL

cap, raise the grip on the

top of the cap until it is

upright at a 90° angle.

Insert the cap in the fuel

tank opening with the

triangular marks on the grip of the cap

and on the fuel tank opening lining up.

Using the grip, turn the cap firmly

clockwise as far as it will go (approx. a

quarter turn).

Fold the grip flush with the

top of the cap. If the grip

does not lie completely

flush with the cap and the

detent on the grip does

not fit in the

corresponding recess in the filler

opening, the cap is not properly seated

and tightened and you must repeat the

above steps.

Screw cap

!Warning!

Unit vibrations can cause an improperly

tightened fuel filler cap to loosen or

come off and spill quantities of fuel. In

order to reduce the risk of fuel spillage

and fire, tighten the fuel filler cap by

hand as securely as possible.

The screwdriver end of

the STIHL combination

wrench or other similar

tool can be used as an aid

in tightening slotted fuel

filler caps.

See "Fueling" chapter in your instruction

manual.

7MS 441

English

Before Starting

Take off the chain guard (scabbard) and

inspect the saw for proper condition and

operation. (See the maintenance chart

near the end of the instruction manual.)

!Warning!

Always check your power tool for proper

condition and operation before starting,

particularly the throttle trigger, throttle

trigger interlock, stop switch and cutting

tool. The throttle trigger must move

freely and always spring back to the idle

position. Never attempt to modify the

controls or safety devices.

!Warning!

Never operate your power tool if it is

damaged, improperly adjusted or

maintained, or not completely or

securely assembled.

!Warning!

Check that the spark plug boot is secure

– a loose boot may cause arcing that

could ignite combustible fumes and

cause a fire.

For proper assembly of the bar and

chain follow the procedure described in

the chapter "Mounting the Bar and

Chain" of your instruction manual.

STIHL Oilomatic chain, guide bar and

sprocket must match each other in

gauge and pitch. Before replacing any

bar and chain, see the sections on

"Specifications," and "Kickback".

!Warning!

Proper tension of the chain is extremely

important. In order to avoid improper

setting, the tensioning procedure must

be followed as described in your

manual. Always make sure the

hexagonal nut(s) for the sprocket cover

is (are) tightened securely after

tensioning the chain in order to secure

the bar. Never start the saw with the

sprocket cover loose. Check chain

tension once more after having

tightened the nut(s) and thereafter at

regular intervals (whenever the saw is

shut off). If the chain becomes loose

while cutting, shut off the engine and

then tighten. Never try to adjust the

chain while the engine is running!

Keep the handles clean and dry at all

times; it is particularly important to keep

them free of moisture, pitch, oil, fuel mix,

grease or resin in order for you to

maintain a firm grip and properly control

your power tool.

Starting

Warning!

To reduce the risk of fire and burn

injuries, start the engine at least 10 feet

(3 meters) from the fueling spot,

outdoors only.

Start and operate your saw without

assistance. For specific starting

instructions, see the appropriate section

of the instruction manual. Proper starting

methods reduce the risk of injury.

!Warning

To reduce the risk of injury from chain

contact and/or reactive forces, the chain

brake must be engaged when starting

the saw.

!Warning!

Do not drop start. This method is very

dangerous because you may lose

control of the saw.

There are two recommended methods

for starting your chainsaw.

8

English

MS 441

With the first recommended method,

the chainsaw is started on the ground.

Make sure the chain brake is engaged

(see "Chain Brake" chapter in your

instruction manual) and place the

chainsaw on firm ground or other solid

surface in an open area. Maintain good

balance and secure footing.

Grip the front handlebar of the saw firmly

with your left hand and press down. For

saws with a rear handle level with the

ground, put the toe of your right foot into

the rear handle and press down. With

your right hand pull out the starter grip

slowly until you feel a definite resistance

and then give it a brisk, strong pull.

The second recommended method for

starting your chainsaw allows you to

start the saw without placing it on the

ground. Make sure the chain brake is

engaged, grip the front handle of the

chainsaw firmly with your left hand.

Keep your arm on the front handle in a

locked (straight) position. Hold the rear

handle of the saw tightly between your

legs just above the knees. Maintain

good balance and secure footing. Pull

the starting grip slowly with your right

hand until you feel a definite resistance

and then give it a brisk, strong pull.

!Warning!

Be sure that the guide bar and chain are

clear of you and all other obstructions

and objects, including the ground. When

the engine is started, the engine speed

with the starting throttle lock engaged

will be fast enough for the clutch to

engage the sprocket and, if the chain

brake is not activated, turn the chain. If

the upper quadrant of the tip of the bar

touches any object, it may cause kick-

back to occur (see section on reactive

forces). To reduce this risk, always

engage the chain brake before starting.

Never attempt to start the chainsaw

when the guide bar is in a cut or kerf.

As soon as the engine is running,

immediately blip the throttle trigger,

which will disengage the starting throttle

lock and allow the engine to settle down

to idle.

!Warning!

When you pull the starter grip, do not

wrap the starter rope around your hand.

Do not let the grip snap back, but guide

the starter rope to rewind it properly.

Failure to follow this procedure may

result in injury to your hand or fingers

and may damage the starter

mechanism.

001BA113 KN

001BA114 KN

9MS 441

English

Important Adjustments

!Warning!

To reduce the risk of personal injury from

loss of control or contact with the

running cutting tool, do not use your unit

with incorrect idle adjustment. At correct

idle speed, the cutting tool should not

move. For directions on how to adjust

idle speed, see the appropriate section

of your instruction manual.

If you cannot set the correct idle speed,

have your STIHL dealer check your

power tool and make proper

adjustments and repairs.

During Operation

Holding and controlling the power

tool

Always hold the unit firmly with both

hands on the handles while you are

working. Wrap your fingers and thumbs

around the handles.

Your right hand should grip the rear

handle. This also applies to left-handers.

With your hands in this position, you can

best oppose and absorb the push, pull

and kickback forces of your saw without

losing control (see section on reactive

forces).

!Warning!

To reduce the risk

of serious or fatal

injury to the

operator or

bystanders from

loss of control, never use the saw with

one hand. It is more difficult for you to

control reactive forces and to prevent

the bar and chain from skating or

bouncing along the limb or log. Even for

those compact saws designed for use in

confined spaces, one-handed operation

is dangerous because the operator may

lose control.

!Warning!

To reduce the risk of cut injuries, keep

hands and feet away from the cutting

tool. Never touch a moving cutting tool

with your hand or any other part of your

body.

!Warning!

Keep proper footing and balance at all

times. Special care must be taken in

slippery conditions (wet ground, snow)

and in difficult, overgrown terrain. Watch

for hidden obstacles such as tree

stumps, roots, rocks, holes and ditches

to avoid stumbling. There is increased

danger of slipping on freshly debarked

logs. For better footing, clear away fallen

branches, scrub and cuttings. Be

extremely cautious when working on

slopes or uneven ground.

!Warning!

Take extreme care in wet and freezing

weather (rain, snow, ice). Put off the

work when the weather is windy, stormy

or rainfall is heavy.

001BA087 LÄ

10

English

MS 441

!Warnin!g

To reduce the risk of injury from loss of

control, never work on a ladder or any

other insecure support. Never hold the

machine above shoulder height. Do not

overreach.

!Warning!

Never work in a tree unless you have

received specific, professional training

for such work, are properly secured

(such as tackle and harness system or a

lift bucket), have both hands free for

operating the chainsaw in a cramped

environment and have taken proper

precautions to avoid injury from falling

limbs or branches.

Position the chainsaw in such a way that

your body is clear of the cutting

attachment whenever the engine is

running. Stand to the left of cut while

bucking.

Never put pressure on the saw when

reaching the end of a cut. The pressure

may cause the bar and rotating chain to

pop out of the cut or kerf, go out of

control and strike the operator or some

other object. If the rotating chain strikes

some other object, a reactive force may

cause the moving chain to strike the

operator.

Working conditions

Operate and start your power tool only

outdoors in a well ventilated area.

Operate it under good visibility and

daylight conditions only. Work carefully.

!Warning!

Your chainsaw is a one-person machine.

Do not allow other persons in the

general work area, even when starting.

Stop the engine immediately if you are

approached.

!Warning!

Even though bystanders should be kept

away from the running saw, never work

alone. Keep within calling distance of

others in case help is needed.

!Warning!

As soon as the engine is

running, this product

generates toxic exhaust

fumes containing

chemicals, such as

unburned hydrocarbons

(including benzene) and carbon

monoxide, that are known to cause

respiratory problems, cancer, birth

defects, or other reproductive harm.

Some of the gases (e.g. carbon

monoxide) may be colorless and

odorless. To reduce the risk of serious or

fatal injury/illness from inhaling toxic

fumes, never run the machine indoors or

in poorly ventilated locations. If exhaust

fumes become concentrated due to

insufficient ventilation, clear

obstructions from work area to permit

proper ventilation before proceeding

and/or take frequent breaks to allow

fumes to dissipate before they become

concentrated.

001BA031 KN

001BA082 KN

11MS 441

English

!Warning!

Inhalation of certain dusts, especially

organic dusts such as mold or pollen,

can cause susceptible persons to have

an allergic or asthmatic reaction.

Substantial or repeated inhalation of

dust and other airborne contaminants, in

particular those with a smaller particle

size, may cause respiratory or other

illnesses. This includes wood dust,

especially from hardwoods, but also

from some softwoods such as Western

Red Cedar. Control dust at the source

where possible. Use good work

practices, such as always cutting with a

properly sharpened chain (which

produces wood chips rather than fine

dust) and operating the unit so that the

wind or operating process directs any

dust raised by the power tool away from

the operator. Follow the

recommendations of occupational and

trade associations with respect to dust

(“particulate matter”). When the

inhalation of dust cannot be substantially

controlled, i.e., kept at or near the

ambient (background) level, the

operator and any bystanders should

wear a respirator complying with your

applicable national standard.

!Warning!

Breathing asbestos dust is dangerous

and can cause severe or fatal injury,

respiratory illness or cancer. The use

and disposal of asbestos-containing

products have been strictly regulated by

the Environmental Protection Agency.

Operating instructions

!Warning!

Do not operate your power tool using the

starting throttle lock, as you do not have

control of the engine speed.

In the event of an emergency, switch off

the engine immediately – move the slide

control / stop switch to 0 or STOP.

!Warning!

Always stop the engine before putting a

chainsaw down.

!Warning!

The saw chain continues to move for a

short period after the throttle trigger is

released (flywheel effect).

Accelerating the engine while the saw

chain is blocked increases the load and

will cause the clutch to slip continuously.

This may occur if the throttle is

depressed for more than a few seconds

when the chain is pinched in the cut or

the chain brake is engaged. It can result

in overheating and damage to important

components (e.g. clutch, polymer

housing components) – which can then

increase the risk of injury, e.g., from the

saw chain moving while the engine is

idling.

! Warning!

Your chainsaw is equipped with a chain

catcher. It is designed to reduce the risk

of personal injury in the event of a

thrown or broken chain. From time to

time, the catcher may be damaged or

removed. To reduce the risk of personal

injury, do not operate a chainsaw with a

damaged or missing chain catcher.

12

English

MS 441

! Warning!

Inspect buffers periodically. Replace

damaged, broken or excessively worn

buffers immediately, since they may

result in loss of control of the saw. A

"sponginess" in the feel of the saw,

increased vibration or increased

"bottoming" during normal operation

may indicate damage, breakage or

excessive wear. Buffers should always

be replaced in sets. If you have any

questions as to whether the buffers

should be replaced, consult your STIHL

servicing dealer.

!Warning!

Your saw is not designed for prying or

shoveling away limbs, roots or other

objects. Such use could damage the

cutting attachment or AV system.

!Warning!

When sawing, make sure that the saw

chain does not touch any foreign

materials such as rocks, fences, nails

and the like. Such objects may be flung

off, damage the saw chain or cause the

saw to kickback.

!Warning!

The muffler and other parts of the engine

(e.g. fins of the cylinder, spark plug)

become hot during operation and remain

hot for a while after stopping the engine.

To reduce risk of burns do not touch the

muffler and other parts while they are

hot.

!Warning!

To reduce the risk of fire and burn injury,

keep the area around the muffler clean.

Remove excess lubricant and all debris

such as pine needles, branches or

leaves. Let the engine cool down sitting

on concrete, metal, bare ground or solid

wood (e.g. the trunk of a felled tree)

away from any combustible substances.

!Warning!

Never modify your muffler. A modified or

damaged muffler could cause an

increase in heat radiation or sparks,

thereby increasing the risk of fire and

burn injury. You may also permanently

damage the engine. Have your muffler

serviced and repaired by your STIHL

servicing dealer only.

Catalytic converter

!Warning!

Some STIHL power tools

are equipped with a

catalytic converter, which

is designed to reduce the

exhaust emissions of the

engine by a chemical

process in the muffler. Due to this

process, the muffler does not cool down

as rapidly as conventional mufflers when

the engine returns to idle or is shut off.

To reduce the risk of fire and burn

injuries, the following specific safety

precautions must be observed.

!Warning!

Since a muffler with a catalytic converter

cools down less rapidly than conven-

tional mufflers, always set your power

tool down in the upright position and

never locate it where the muffler is near

dry brush, grass, wood chips or other

combustible materials while it is still hot.

!Warning!

An improperly mounted or damaged

shroud or a damaged/deformed muffler

shell may interfere with the cooling

process of the catalytic converter. To

reduce the risk of fire or burn injury, do

not continue work with a damaged or

improperly mounted cylinder shroud or a

damaged/deformed muffler shell.

Your catalytic converter is furnished with

screens designed to reduce the risk of

fire from the emission of hot particles.

Due to the heat from the catalytic

reaction, these screens will normally

stay clean and need no service or

maintenance. If you experience loss of

performance and you suspect a clogged

screen, have your muffler maintained by

a STIHL servicing dealer.

13MS 441

English

Reactive forces including kickback

!Warning!

Reactive forces may occur any time the

chain is rotating. Reactive forces can

cause serious personal injury.

The powerful force used to cut wood can

be reversed and work against the

operator. If the rotating chain is suddenly

stopped by contact with any solid object

such as a log or branch or is pinched, the

reactive forces may occur instantly.

These reactive forces may result in loss

of control, which, in turn, may cause

serious or fatal injury. An understanding

of the causes of these reactive forces

may help you avoid the element of

surprise and loss of control. Sudden

surprise contributes to accidents.

The most common reactive forces are:

– kickback,

– pushback,

– pull-in.

Kickback:

Kickback may occur when

the moving saw chain

near the upper quadrant

of the bar nose contacts a

solid object or is pinched.

The reaction of the cutting force of the

chain causes a rotational force on the

chainsaw in the direction opposite to the

chain movement. This may fling the bar

up and back in a ligtening fast reaction in

an uncontrolled arc mainly in the plane

of the bar. Under some cutting

circumstances the bar moves towards

the operator, who may suffer severe or

fatal injury.

Kickback may occur, for example,

when the chain near the upper quadrant

of the bar nose contacts the wood or is

pinched during limbing or when it is

incorrectly used to begin a plunge or

boring cut.

The greater the force of the kickback

reaction, the more difficult it becomes for

the operator to control the saw. Many

factors influence the occurrence and

force of the kickback reaction. These

include chain speed, the speed at which

the bar and chain contact the object, the

angle of contact, the condition of the

chain and other factors.

The type of bar and saw chain you use

is an important factor in the occurrence

and force of the kickback reaction. Some

STIHL bar and chain types are designed

to reduce kickback forces. STIHL

recommends the use of reduced

kickback bars and low kickback chains.

001BA093 LÄ

001BA035 KN

14

English

MS 441

Devices for reducing the risk of

kickback injury

STIHL recommends the use of the

STIHL Quickstop chain brake on your

powerhead with green labeled reduced

kickback bars and low kickback chains.

!Warning!

To reduce the risk of injury, never use a

saw if the chain brake does not function

properly. Take the saw to your local

STIHL servicing dealer. Do not use the

saw until the problem has been rectified.

STIHL Quickstop chain brake

STIHL has developed a chain stopping

system designed to reduce the risk of

injury in certain kickback situations. It is

called a Quickstop chain brake. The

Quickstop chain brake is standard

equipment on your STIHL chainsaw.

When a kickback occurs, the guide bar

may rotate around the front handle. If the

cutting position is such that the

operator's left hand is gripping the front

handle behind the hand guard, and if the

left hand rotates around the front handle

and makes a sufficiently forceful contact

with the front hand guard, which is the

Quickstop activating lever, this contact

will activate a properly maintained

Quickstop chain brake. The chain brake

on newer STIHL chainsaws can also be

activated by inertia. If the kickback

forces are sufficiently high, the hand

guard is accelerated towards the bar

nose even without hand contact. See the

chapter entitled "Chain Brake" of your

instruction manual.

!Warning!

Never operate your chainsaw without a

front hand guard. In a kickback situation

this guard helps protect your left hand

and other parts of your body. In addition,

removal of the hand guard on a saw

equipped with a Quickstop chain brake

will deactivate the chain brake.

!Warning!

No Quickstop or other chain brake

device prevents kickback. These

devices are designed to reduce the risk

of kickback injury, if activated, in certain

kickback situations. In order for the

Quickstop to reduce the risk of kickback

injury, it must be properly maintained

and in good working order. See the

chapter of your instruction manual

entitled "Chain Brake" and the section

"Maintenance, Repair and Storing" at

the end of these Safety Precautions. In

addition, there must be enough distance

between the bar and the operator to

ensure that the Quickstop has sufficient

time to activate and stop the chain

before potential contact with the

operator.

001BA174 KN

15MS 441

English

!Warning!

An improperly maintained chain brake

may increase the time needed to stop

the chain after activation, or may not

activate at all.

!Warning!

Never run the chainsaw above idle

speed for more than 3 seconds when the

chain brake is engaged or when the

chain is pinched or otherwise caught in

the cut. Clutch slippage can cause

excessive heat, leading to severe

damage of the motor housing, clutch

and oiler component and may interfere

with the operation of the chain brake. If

clutch slippage in excess of 3 seconds

has occurred, allow the motor housing to

cool before proceeding and check the

operation of your chain brake as

described in the chapter entitled "Chain

Brake" of your instruction manual. Also

make sure that the chain is not turning at

idle speed (see above at "Important

Adjustments").

Low kickback saw chain and reduced

kickback bars

STIHL offers a variety of bars and

chains. STIHL reduced kickback bars

and low kickback chains are designed to

reduce the risk of kickback injury. Other

chains are designed to obtain higher

cutting efficiency or sharpening ease but

may result in higher kickback tendency.

STIHL recommends the use of its

reduced kickback bars, low kickback

chains and a STIHL Quickstop chain

brake for both experienced and

inexperienced chainsaw users.

Please ask your STIHL dealer to

properly match your powerhead with the

appropriate bar/chain combination to

reduce the risk of kickback injury. Green

labeled bars and chains are

recommended for all powerheads.

Warning!

Use of other, non-listed bar/chain

combinations may increase kickback

forces and the risk of kickback injury.

New bar/chain combinations may be

developed after publication of this

literature, which comply with

§ 4.1.3 of CSA Standard Z 62.3-04

Chain Saw Kickback. Check with your

STIHL dealer for such combinations.

!Warning!

Reduced kickback bars and low

kickback chains do not prevent

kickback, but they are designed to

reduce the risk of kickback injury. They

are available from your STIHL dealer.

!Warning!

Even if your saw is equipped with a

Quickstop, a reduced kickback bar and/

or low kickback chain, this does not

eliminate the risk of injury by kickback.

Therefore, always observe all safety

precautions to avoid kickback situations.

16

English

MS 441

Low kickback chain

Some types of saw chain have specially

designed components to reduce the

force of nose contact kickback. STIHL

has developed low kickback chain for

your powerhead.

"Low kickback saw chain" is a chain

which has met the kickback

performance requirements of § 4.1.3.2

of CSA Standard Z 62.3-04 Chain Saw

Kickback when tested in its original

condition on a selected representative

sample of chainsaws.

!Warning!

There are potential powerhead and bar

combinations with which low kickback

saw chains can be used which have not

been specifically certified to comply with

the 60 ° / 45 ° computer derived kickback

angle of § 4.1.3 of CSA Standard Z 62.3-

04 Chain Saw Kickback. Some low

kickback chains have not been tested

with all powerhead and bar

combinations.

!Warning!

A dull or improperly sharpened chain

may reduce or negate the effects of the

design features intended to reduce

kickback energy. Improper lowering or

sharpening of the depth gauges or

shaping of the cutters may increase the

chance and the potential energy of a

kickback. Always cut with a properly

sharpened chain.

Reduced kickback bars

STIHL green labeled reduced kickback

bars are designed to reduce the risk of

kickback injury when used with STIHL

green labeled low kickback chains.

!Warning!

When used with other, more aggressive

chains, these bars may be less effective

in reducing kickback.

Bow Guides

!Warning!

Do not mount a bow guide on any STIHL

chainsaw. Any chainsaw equipped with

a bow guide is potentially very

dangerous. The risk of kickback is

increased with a bow guide because of

the increased kickback contact area.

Low kickback chain will not significantly

reduce the risk of kickback injury when

used on a bow guide.

To avoid kickback

The best protection from personal injury

that may result from kickback is to avoid

kickback situations:

1. Hold the chainsaw firmly with both

hands and maintain a secure grip.

Don’t let go.

2. Be aware of the location of the guide

bar nose at all times.

3. Never let the nose of the guide bar

contact any object. Do not cut limbs

with the nose of the guide bar. Be

especially careful near wire fences

and when cutting small, tough

limbs, small size brush and saplings

which may easily catch the chain.

4 Don't overreach.

5. Don't cut above shoulder height.

6. Begin cutting and continue at full

throttle.

7. Cut only one log at a time.

8. Use extreme caution when

reentering a previous cut.

9. Do not attempt to plunge cut if you

are not experienced with these

cutting techniques.

10. Be alert for shifting of the log or

other forces that may cause the cut

to close and pinch the chain.

11. Maintain saw chain properly. Cut

with a correctly sharpened, properly

tensioned chain at all times.

12. Stand to the side of the cutting path

of the chainsaw.

17MS 441

English

A = Pull-in

Pull-in occurs when the chain on the

bottom of the bar is suddenly stopped

when it is pinched, caught or encounters

a foreign object in the wood. The

reaction of the chain pulls the saw

forward and may cause the operator to

lose control.

Pull-in frequently occurs when the

bumper spike of the saw is not held

securely against the tree or limb and

when the chain is not rotating at full

speed before it contacts the wood.

!Warning!

Use extreme caution when cutting small

size brush and saplings which may

easily catch the chain, be whipped

towards you or pull you off balance.

To avoid pull-in

1. Always start a cut with the chain

rotating at full speed and the

bumper spike in contact with the

wood.

2. The risk of pull-in may also be

reduced by using wedges to open

the kerf or cut.

B = Pushback

Pushback occurs when the chain on the

top of the bar is suddenly stopped when

it is pinched, caught or encounters a

foreign object in the wood. The reaction

of the chain may drive the saw rapidely

straight back toward the operator and

may cause loss of saw control.

Pushback frequently occurs when the

top of the bar is used for cutting.

To avoid pushback

1. Be alert to forces or situations that

may cause material to pinch the top

of the chain.

2. Do not cut more than one log at a

time.

3. Do not twist the saw when

withdrawing the bar from a plunge

cut or underbuck cut because the

chain can pinch.

Cutting Techniques

Felling

Felling is cutting down a tree.

Before felling a tree, consider carefully

all conditions which may affect the

direction of fall.

!Warning!

There are a number of factors that may

affect and change the intended direction

of fall, e.g. wind direction and speed,

lean of tree, surrounding trees and

obstacles, sloping ground, one-sided

limb structure, wood structure, decay,

snow load, etc. To reduce the risk of

severe or fatal injury to yourself or

others, look for these conditions prior to

beginning the cut, and be alert for a

change in direction while the tree is

falling.

!Warning!

Always observe the general condition of

the tree. Inexperienced users should

never attempt to cut trees which are

decayed or rotted inside or which are

leaning or otherwise under tension.

There is an increased risk that such

trees could snap or split while being cut

and cause serious or fatal injury to the

operator or bystanders. Also look for

broken or dead branches which could

vibrate loose and fall on the operator.

When felling on a slope, the operator

should stand on the uphill side if

possible.

001BA037 KN

A

001BA038 KN

B

18

English

MS 441

Felling Instructions:

When felling, maintain a distance of at

least 2 1/2 tree lengths from the nearest

person.

When felling in the vicinity of roads,

railways and power lines, etc., take extra

precautions. Inform the police, utility

company or railway authority before

beginning to cut.

!Warning!

The noise of your engine may drown any

warning call.

Escape path

First clear the tree base and work area

from interfering limbs and brush and

clean its lower portion with an ax.

Then, establish two paths of escape (B)

and remove all obstacles. These paths

should be generally opposite to the

planned direction of the fall of the tree

(A) and about at a 45° angle. Place all

tools and equipment a safe distance

away from the tree, but not on the

escape paths.

Buttress roots

If the tree has large buttress roots, cut

into the largest buttress vertically first

(horizontally next) and remove the

resulting piece.

Gunning sight

When making the felling notch, use the

gunning sight on the shroud and housing

to check the desired direction of fall:

Position the saw so that the gunning

sight points exactly in the direction you

want the tree to fall.

001BA088 LÄ

2

/

1

2

1 1

/

1

2

B

001BA040 KN

A

45°

B

001BA146 KN

001BA153 KN

19MS 441

English

Conventional cut

C = felling notch - determines the

direction of the fall

For a conventional cut:

: Properly place felling notch

perpendicular to the line of fall,

close to the ground.

: Cut down at app. 45-degree angle

to a depth of about 1/5 to 1/4 of the

trunk diameter.

: Make second cut horizontal.

: Remove resulting 45-degree piece.

Open-face technique

C = felling notch - determines the

direction of the fall

For an open-face cut:

: Properly place felling notch

perpendicular to the line of fall,

close to the ground.

: Cut down at app. 50-degree angle

to a depth of app.1/5 to 1/4 of the

trunk diameter.

: Make second cut from below at app.

40 degree angle.

: Remove resulting 90-degree piece.

Making sapwood cuts

: For medium sized or larger trees

make cuts at both sides of the trunk,

at same height as subsequent

felling cut.

: Cut to no more than width of guide

bar.

This is especially important in softwood

in summer - it helps prevent sapwood

splintering when the tree falls.

001BA143 KN

C

001BA143 KN

C

001BA150 KN

La page charge ...

STIHL MS 441 C Manuel utilisateur

STIHL MS 441 C Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents