VTech Telecommunications EW780-0348-00 Manuel utilisateur

VH6210

Convertible Ofﬁce

Wireless Headset

VH6211

Convertible Ofﬁce

Wireless Headset

with Lifter

Abridged user’s manual

BC

Go to

businessphones.vtech.com

to register your product for

enhanced warranty support

and the latest VTech product

news.

Congratulations

on your purchase of this VTech product. Before using this product,

please read the Important safety information.

This Abridged user’s manual provides you with the basic

installation and use instructions. A limited set of features are

described in abbreviated form.

Visit businessphones.vtech.com/support/downloads to

download a full set of installation and operation instructions for:

Headset connection methods

“Option 1: Connect to IP phone via EHS”

“Option 2: Connect to traditional corded phone”

“Option 3: Connect to traditional corded phone with Lifter”

“Option 4: Connect to a computer”

Headset wearing styles

“Over-the-ear hook”

“Over-the-head band”

“Behind-the-neck band”

VTech Softphone Call Manager

“VTech Softphone Call Manager -

Installation and Operation Guide”

For customer service or product information, visit our website at

businessphones.vtech.com or call 1 (800) 595-9511. In Canada,

please dial 1 (800) 267-7377.

•

T

Compatible with

Hearing Aid T-Coil

TIA-1083

Telephones identified with this logo have reduced noise and

interference when used with most T-coil equipped hearing aids and

cochlear implants. The TIA-1083 Compliant Logo is a trademark of

the Telecommunications Industry Association. Used under license.

The VH6210/VH6211 includes a cordless headset and base that

allow you to have handsfree phone conversations.

The package also comes with the EHS (Electronic hookswitch)

cables and headset audio cables that allow you to connect your

headset in either one or both of the following methods:

PHONE mode - Connect to a deskphone

If you want to connect your headset to a deskphone, you can

simply use the cables provided to connected the headset to a

deskphone directly.

PC mode - Connect to a computer

Use the USB cable to connect the headset base and your

PC. You can monitor VoIP calls through Skype

®

or Skype for

Business

®

using the VTech Softphone Call Manager.

VTech Softphone Call Manager is the hub for call control,

which enables you to answer or end, and mute or end mute a call

directly from your headset. You can also configure the advanced

feature settings, such as low battery alert, ringer tone, second

inbound call alert, or microphone mute alert at the software.

VH6211 Convertible Office Wireless Headset with Lifter:

The VH6211 package also comes with the extra corded handset

lifter, making it convenient to answer and end calls right from the

headset, so that the product can be used in different ways depending

on your needs.

For lifter’s information, refer to the section Lifter.

•

Introduction

Skype

®

and Skype for Business

®

are registered trademarks of Microsoft Corporation.

Batteries with battery

compartment cover

Wireless headset

with earbud and hook

Behind-the-neck band

Four over-the-ear hooksFour earbuds

Over-the-head band

What’s in the box

Your product package contains the following items. Save your

sales receipt and original packaging in the event warranty service

is necessary.

User's manual

For VH6210/VH6211:

USB cable

Headset base

power adapter

Corded phone

connection cable

Headset base

What’s in the box

Headset audio cable

EHS cable 1 EHS cable 2

Auxiliary ring detectorCorded handset lifter

For VH6211 only:

For VH6210/VH6211 (con’t):

Table of contents

Overview

Headset ...................................1

Headset base ..........................2

Install headset battery .............4

Power up the headset base .....5

Charge the headset battery .....5

Charge and store your spare

battery ..................................6

Connection methods ................7

PHONE mode .......................7

PC mode ...............................7

Option 1: Connect to

IP phone via EHS .................8

Option 2: Connect to

a traditional corded phone ....9

Option 3: Connect to

a traditional corded phone

with Lifter (for VH6211 only) ...9

Option 4: Connect to a

computer ..............................9

Position the headset ..............10

Over-the-ear hook ...............10

Over-the-head band ............10

Behind-the-neck band .........10

Before use

Headset operation .................11

Headset power on/off ..........11

PHONE mode and

PC mode ............................11

Operate

PHONE mode ........................12

Operate with IP phone

via EHS ..............................12

Operate with corded phone ...13

Operate with corded

phone via Lifter ...................13

PC mode ................................14

VTech Softphone Call

Manager .............................14

Call settings ...........................15

Auto Answer........................15

Change Audio Bandwidth ...15

Headset ringer ....................16

Anti-Startle (G616) .............16

Temporary ringer silencing ...17

Volume control ....................17

Mute ....................................17

Hot-swappable headset

battery replacement ............18

Lifter (for VH6211 only)

Overview ................................20

Connect the Lifter ..................22

Operate with Lifter .................22

Appendix

Adding and registering

a new headset ....................23

Headset lights ........................24

Headset alert tones ............25

Headset alert prompts ........25

Headset base lights ...............26

Frequently asked questions ...27

Maintenance ..........................33

Important safety information ... 34

Safety information ...............34

Especially about wireless

headsets .............................35

Precautions for users

of implanted cardiac

pacemakers ........................36

For C-UL compliance .............37

Mesures de sécurité

importantes .........................37

FCC Part 68 and ACTA .........41

FCC Part 15 ...........................43

California Energy

Commission battery

charging testing

instructions .........................44

Limited warranty ....................45

Disclaimer and Limitation of

Liability ...............................48

Technical speciﬁcations .........49

1

Headset

Overview

1

2

3

4

5

1 –VOL+/VOL-

Slide the volume switch to the right or left to adjust the headset ringer volume

while in idle mode, or the listening volume while on a call.

2 – ON/OFF button and LED light

Press to make, answer or end a call.

See page 24 for lights behavior.

3 – MUTE

Mute the microphone during a call.

4 – Battery with cover attached

The battery is permanently attached to the battery compartment cover and

they are inseparable from each other. Remove the entire assembled unit to

replace the battery.

5 – Microphone

•

22

Overview

Headset base

7

8

1

9

13

14

15

12

10

11

2

3

4

6

5

7

8

1

9

13

14

15

12

10

11

2

3

4

6

5

1 – VOLUME / MICROPHONE

Press to adjust the speaking volume while on a call.

2 – Magnetic charging mount

Place the headset here for charging.

3 – MUTE/SPARE BATT (light)

See page 26 for lights behavior.

4 – PHONE (mode button and light)

Press to enter the PHONE mode.

See page 26 for lights behavior.

5 – PC (mode button and light)

Press to enter the PC mode.

See page 26 for lights behavior.

6 – PAIR

Press to initiate headset registration or deregistration.

7 – Spare battery compartment cover

8 – POWER jack (green dot)

9 – PHONE jack (blue dot)

10 – EHS jack (red dot)

•

33

Overview

7

8

1

9

13

14

15

12

10

11

2

3

4

6

5

11 – (USB port)

Open the port cover to plug in the USB cable for use with PC mode.

12 – LIFTER jack (for VH6211 only)

13 – AutoAns ON/OFF

When turned on, your headset will then automatically answer a call when it is

lifted from the charging cradle.

14 – Corded handset audio adjust switch

Use this switch to adjust the corded handset audio when you have connected

the headset base to a corded telephone.

15 – WB (Wideband) / NB (Narrowband) switch

Use this switch to adjust the audio bandwidth.Wideband audio delivers wider

frequency response and higher HD audio quality.

•

Headset base

44

Getting started

Install headset battery

CAUTION

Do not disassemble the battery from its battery compartment cover.•

NOTES:

You will hear the voice prompt "Low battery" when you press the ON/OFF

button while the headset battery is low.

When fully charged, the headset battery supports up to 5 hours of talk time or 48

hours of standby time.

If you slide the WB / NB (wideband/narrowband) switch to WB for enhanced

audio quality, the power consumption will also be increased, thereby resulting in

reduced talk time (see(see page 15).

To order a replacement battery pack (model BT291865), visit our website at

businessphones.vtech.com or call 1 (800) 595-9511. In Canada, dial

1 (866) 267-7377.

•

1. Align the metallic contacts between the battery and the battery

compartment, and then place the battery down.

2. Slide the battery until it clicks into place.

3. Charge it for at least 30 minutes.

55

Getting started

Charge the headset battery

Hang the headset onto the magnetic charging mount.

The magnet holds the headset in place.

• The light will turn:

- steady red when the headset

battery is low while charging;

- steady purple when well

charged; and

- steady blue when fully charged.

• The MUTE | SPARE BATT

LED

light will turn:

- steady green when the spare

battery is charging; and

- off when it is fully charged.

NOTE:

For optimal performance, charge the headset battery for at least 30 minutes before

use. The battery is fully charged after 2 hours of continuous charging. When the

headset is not in use, recharge by hanging it onto the headset base.

•

Power up the headset base

Plug the small end of the headset

base power adapter labelled

to the POWER jack (green dot)

at the rear of the headset base.

Plug the large end into an

electrical outlet not controlled by

a wall switch.

1.

2.

66

Getting started

Charge and store your spare battery

You can install the spare battery into your headset base for

charging and storage purposes.

The headset supports hot swapping, in which the current call on

the headset will remain connected if you replace the battery within

5 minutes. You can even have an unlimited talk time with timely

battery replacement.

Align the metallic contacts between the battery and the battery

compartment, and then place the battery down.

2. Slide the battery until it clicks into place.

• The MUTE | SPARE BATT light turns green when charging.

3. Slide the battery compartment cover back to the headset base.

1.

NOTE:

For optimal performance, charge the spare battery for at least 30 minutes before

use. The battery is fully charged after 2 hours of continuous charging. When the

headset is not in use, recharge by placing it into the headset base.

•

77

Getting started

Connection methods

Choose one of the following methods to connect your headset for

operation in either PHONE mode or PC mode.

PHONE mode

Option 1: Connect to IP phone via EHS

You

can connect the headset to an IP phone using the EHS

cable and headset audio cable provided. The headset acts as

a supplementary device that can join calls. Use the IP phone

connected to make or answer calls.

Option 2: Connect to traditional corded phone

You

can connect the headset to a traditional corded phone

using the

corded phone connection cable

provided. You need

to physically lift the corded handset off the corded phone base

cradle before you can use the headset to join in the call.

Option 3: Connect to traditional corded phone with

Lifter (for VH6211 only)

You

can connect the headset to a corded phone using the corded

phone connection cable and lifter provided (

see page

22). The

headset acts as a supplementary device that can join calls. You

can simply press on the headset to use the connected corded

phone to make or answer calls.

PC mode

Option 4: Connection to a computer

Connect the headset base to your PC with the USB cable

provided. You can make and answer VoIP calls through Skype or

Skype for Business, using the VTech Softphone Call Manager.

•

88

Getting started

Connection methods

NOTE:

The cords have colored labels that guide you to plug them into the correct headset

base jacks. The back of the headset base has color-coded dots and the names

of the jacks above them that correspond to the colored labels on the cords.

For detailed instructions of the four options to connect

your headset, visit the product page of VH6210 or VH6211

at businessphones.vtech.com/support/downloads to

download the respective instructional document.

Option 1: Connect to IP phone via EHS

C

onnect the headset to an IP phone using the EHS cable and

headset audio cable provided.

Visit businessphones.vtech.com for the compatibility lists of IP

phone models that are compatible for EHS connection, as well as

the respective EHS adapter(s) that you need to purchase separately.

•

Connect to a VTech VSP08

Series or SNOM D3 Series

IP phone (with EHS cable 1)

Connect to a SNOM D7 Series

IP phone (with EHS cable 2)

EHS cable 1 EHS cable 2

Headset

audio

cable

Headset

audio

cable

99

Getting started

Option 3: Connect to a traditional corded phone with Lifter

(for VH6211 only)

U

se the corded phone

connection cable and lifter

provided

to c

onnect the

headset to a traditional

corded phone

Option 4: Connect to a computer

Use the USB cable provided

to connect the headset to

your computer. Your

headset supports calls

through Skype

or Skype for Business

softphone calls. Install VTech

Softphone Call Manager

before operating in PC mode.

Connection methods

Option 2: Connect to a traditional corded phone

Use the

corded phone

connection cable

provided

to connect the headset to

a traditional corded phone.

Corded phone

connection cable

USB cable

Corded phone

connection cable

1010

Getting started

Position the headset

You can choose from three wearing styles according to your own

preference - over-the-ear, over-the-head, and behind-the-neck.

For detailed instructions of the three wearing styles of

headset, visit the product page of VH6210 or VH6211 at

businessphones.vtech.com/support/downloads to

download the respective instructional document.

Over-the-head band

Attach the headband and ﬁt it to

your head.

•

Behind-the-neck band

Attach the headband and place it around

your head.

•

Over-the-ear hook

Use the earhook and earbud to ﬁt the headset

to your ear.

•

11

Headset operation

Headset power on/off

To power on the headset:

Place the headset in the headset base.

-OR-

Press and hold ON/OFF button for two seconds.

The LED light flashes blue three times, and you hear three

beeps when it is being powered on.

To power off the headset:

Press and hold ON/OFF button for four seconds.

The LED light flashes red three times, and you hear three

beeps when it is being powered off.

PHONE mode and PC mode

Before using the headset, you may change the operation mode

of your headset. When the headset is not in use, you can choose

between PHONE mode and PC mode.

To choose PHONE mode:

Press the PHONE button on the headset base. The PHONE light

turns on.

To choose PC mode:

Press the PC button on the headset base. The PC light turns on.

NOTE:

You can also switch back and forth between PHONE mode and

PC

mode while

on a call. Once selected, the PHONE mode light or the

PC

mode light flashes

twice every three seconds to indicate that line is on hold.

•

Before use

12

PHONE mode

Before using the headset with your telephone connected, make

sure you have chosen PHONE mode.

To choose PHONE mode:

Press the PHONE button on the headset base. The PHONE light

turns on.

Operate with IP phone via EHS

To make a call:

1.

Press the

ON/OFF button

on the headset. The EHS connection

automatically takes the line on your IP phone. You hear a dial tone

in the headset earpiece.

2. Dial the telephone number using the dialing keys on the IP

phone.

NOTE:

The headset supports hot swapping, in which the current call on the headset will

remain connected if you replace the battery within five minutes.

To answer a call:

Press

the

ON/OFF button

on the headset to answer an

incoming call, or lift the headset if auto answer is set to on.

The EHS connection automatically takes the line on your IP phone.

You hear the caller through the headset earpiece.

To end a call:

Press

the

ON/OFF button

on the headset to end a call.

The EHS

connection automatically releases the line on your IP phone.

•

Operate

13

Operate

13

PHONE mode

Operate with corded phone

To make a call:

1.

Lift the corded handset to take the line at your

corded

phone.

2. Press

the

ON/OFF button

on the headset.

You hear a dial tone

in the headset earpiece.

3. Dial the telephone number using the dialing keys on the corded

phone.

NOTE:

The headset supports hot swapping, the current call on the headset will remain

connected if you replace the battery within five minutes.

To answer a call:

1.

Lift the corded handset to take the line at your

corded

phone.

2. Press

the

ON/OFF button

on the headset to answer an

incoming call.

You hear the caller through the headset earpiece.

To end a call:

1. Press

the

ON/OFF button

on the headset to leave the phone

conversation at the headset.

2.

Place the corded handset back to the corded phone to end the call.

Operate with corded phone via Lifter

For calls operation with a traditional corded phone via Lifter, see

page

22

.

•

La page charge ...

VTech Telecommunications EW780-0348-00 Manuel utilisateur

Ce manuel convient également à

VTech Telecommunications EW780-0348-00 Manuel utilisateur

dans d''autres langues

Autres documents