England's Stove Works 25-PDVC Installation & Operation Manual

Marque: England's Stove Works

Modèle: 25-PDVC

Catégorie: Cheminées

Taper: Installation & Operation Manual

Ce manuel convient également à

INSTALLATION & OPERATION MANUAL







Manufactured By:

England’s Stove Works, Inc.

PO Box 206

Monroe, VA 24574

9/6/

SAVE THESE

Pellet Stove

MODELS 25-PDVC / 55-SHP10 / 55-TRP10

SAVE THESE INSTRUCTIONS

TABLEOFCONTENTS

Introduction

 Precautionary Statements ........................ 3

 Message from Us ..................................... 4

 Read Before Getting Started .................... 5

 Important Information ............................. 6

Installation

 Unit Preparation ...................................... 7

 Flue System ............................................. 8

 Pellet Vent Pipe ......................... 8

 Through the Wall ...................... 8

 Through the Ceiling .................. 9

 Existing Flue System ................. 9

 Outside Air ................................ 9

 Mobile Home Installation ........................ 9

 Installation Diagrams ............................. 10

 Floor and Wall Protection ..................... 10

 Vent Termination Clearances ................ 11

OperatingInstructions

 Explanation ............................................ 12

 Start-Up Procedure ................................ 12

 E-Codes ................................................. 13

 Shut-Down Procedure ........................... 13

 Daily Operation ..................................... 14

 Refueling ................................. 14

 Power Outage .......................... 14

 Fuel Outage ............................. 14

 Combustion Blower Failure .... 14

AshRemoval/Maintenance

 Daily ...................................................... 15

 Semi-Weekly ......................................... 15

 Monthly ................................................. 16

 Annual ................................................... 16

 Rear Panel Removal .............................. 17

 Auger Motors ........................................ 17

 Auger Bearings & Shafts ....................... 17

 Convection Blower ................................ 17

 Combustion Blower ............................... 17

 Vacuum Switch ..................................... 18

 Vacuum Switch Port .............................. 18

 Hopper Lid Switch ................................ 19

 Gaskets .................................................. 19

 Finish ..................................................... 19

 Glass ...................................................... 19

 Control Board ........................................ 20

 Wiring Diagram ..................................... 21

 Hopper Lid Latches ............................... 22

 Accessory Items .................................... 23

IllustratedPartsDetail

 Parts List ................................................ 24

 Exploded Parts Diagram ........................ 25

TroubleshootingGuide

 Troubleshooting ..................................... 26

Warranty

 Serial Tag Sample ................................. 27

 Warranty Details .................................... 28

 Warranty Registration Form .................. 29

INSTALLATION & OPERATION MANUAL

MODEL NUMBERS: 25-PDVC 55-SHP10 55-TRP10

Thank you for purchasing this product from a fine line of heating equipment. We wish you many

years of safe heating pleasure with your new heating appliance.

Save These Instructions.

IMPORTANT: IF YOU HAVE A PROBLEM WITH THIS UNIT DO NOT RETURN IT TO THE

DEALER. CONTACT TECHNICAL SUPPORT @ 1-800-245-6489.

Please Note the Following Precautionary Statements:

NOTE: WE DO NOT RECOMMEND PELLET STOVES AS YOUR ONLY SOURCE OF HEAT.

CAUTION: Please read this entire manual before installation and use of this pellet

fuel burning room heater.

Keep children, furniture, fixtures, and all combustible materials away from

any heating appliance. Refer to this owner’s manual for all clearances to

combustible materials.

WARNING: USE OF OUTSIDE AIR IS MANDATORY WITH THIS UNIT.

DO NOT OPERATE UNIT WITH HOPPER OPEN. LID MUST BE SHUT AND TIGHTLY SECURED.

DO NOT OPERATE WITH DOOR OPEN

SAFETY NOTICE

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE,

BODILY INJURY OR EVEN DEATH. FOR YOUR SAFETY AND PROTECTION, FOLLOW ALL

THE INSTALLATION INSTRUCTIONS. CONTACT YOUR LOCAL BUILDING OR FIRE OFFICIALS

FOR RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS (INCLUDING

PERMITS) IN YOUR AREA.

Questions? Need Parts or Options? www.englanderstoves.com

England’s Stove Works highly recommends the use of smoke detectors and Carbon Monoxide

detectors with any hearth product, including this unit. Follow all manufacturer’s instructions when

using smoke or Carbon Monoxide detectors.

Mobile Home Use:

These freestanding pellet units are approved for mobile home or doublewide installation with

outside combustion air hook-up. See “Flue System” section of manual.

Mobile home installation should be in accordance with the Manufactured Home and Safety

Standard (HUD), CFR 3280, Part 24.

WARNING

: Do Not Install in Sleeping Room

CAUTION

: The structural integrity of the mobile home floor, wall and ceiling/roof

ust

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

A letter from our Technical Support Department:

Thank you

for purchasing this fine product from England’s Stove Works!

England's Stove Works was started, and is still owned by, a family that

believes strongly in a "Do It Yourself" spirit – that’s one reason you found

this product at your favorite “Do It Yourself” store.

We intentionally design and build our stoves so that any homeowner can

maintain his or her unit with basic tools, and we're always more than

happy to show you how to do the job as easily and as inexpensively as

possible.

From our free,

downloadable service sheets; to our Pellet Service Video;

to our new "wizard-style," click-through Troubleshooting guide on our

web site, we have always tried to help our customers stay "heat-ready,"

especially when oil and electricity prices continue to skyrocket.

Please look at our vast Help section on our web site and call our

Technical Support department at (800) 245-6489 if you need any help with

your unit. We are nearly always

able to help “walk you through” any

repairs, problems or questions you may have.

PLEASE NOTE

: While information obtained on our web site and through

our 800 number is always free of charge, there will be a service charge

incurred with any “on-site” repairs or maintenance that we may arrange.

Wishing you years of efficient, quality and “comfy” heating,

England’s Stove Works

Technical Support Department

www.englanderstoves.com

(800) 245-6489

IF YOU HAVE A PROBLEM WITH THIS UNIT DO NOT RETURN IT TO THE DEALER.

CONTACT TECHNICAL SUPPORT at 1 (800) 245-6489.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

BEFORE RE-STARTING YOUR UNIT

Every time before pressing “ON” to start your

unit – Be sure to remove all ashes (burnt or

partially burnt) from your burn pot area!

Wearing protective gloves and with the unit

cool, remove the Wear Plate and dump the

ashes, ensuring that the air holes are clear

from debris. Also be sure to follow all other

maintenance instructions as outlined in your

Owner’s Manual and the Instructional DVD

included with the unit. Failure to remove

ashes from this area before each burn

can

cause smoke-back and serious damage to

your stove, and can void your warranty. We

will not be held responsible for poorly

maintained units, including excess ash in the

burn pot area.

Burn Safe and Burn Clean –

Clean the burn pot area daily!

A NOTE ON COLD AIR RETURNS AND

CENTRAL FURNACES

Some homes, including the modern, air-tight homes that are well-insulated, create a negative draft that

could cause smoke to be released from your unit, especially if it is too close to your home’s Central

Furnace. If you install your stove in the same room as the Cold Air Return from your home’s Central

Furnace, you must place your stove at least 20 feet (20’) from the Cold Air Return. We recommend you

open an outside window slightly, and never close the door that leads from this room to the rest of your

home.

IN THE EVENT OF SMOKE-BACK

1. If you see smoke coming out of your unit into the room due to a power failure,

DO NOT OPEN THE HOPPER OR DOOR TO YOUR UNIT!! Remain calm

Open the nearest outside door and windows and wait for all signs of smoke to clear (at least one

hour, although the smoke should dissipate quickly once the door and windows are opened). When

power is restored, press the ON button to restart your unit, and let the unit run for at least 30 minutes.

-- If you see any further signs of smoke-back, press the OFF button and call Technical Support at

(800) 245-6489 before restarting your unit, as damage could have occurred due to the power failure.

-- If you see no more signs of smoke-back, press the OFF button and wait for your unit to completely

shut down and cool down, then clean the burn pot area before restarting your unit (see “Before Re-

Starting Your Unit,” above).

2. If you see smoke coming out of your unit into the room and the power has not failed,

DO NOT OPEN THE HOPPER OR DOOR TO YOUR UNIT!! Remain calm

Immediately press the OFF button, open the nearest outside door and windows and wait for all signs

of smoke to clear (at least one hour, although the smoke should dissipate quickly once the door and

windows are opened). Do NOT restart your unit before calling Technical Support at (800) 245-6489.

Please call Technical Support at (800) 245-6489 with any questions. England’s Stove Works, Inc.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

IMPORTANT INFORMATION

1. Check local installation codes for your area. Call your Homeowner’s Insurance representative for

inspection of your stove’s installation.

2. Read and comply with the instructions in this manual.

3. This unit should be tested (dry run) before loading pellets for 20 minutes. The stove should

automatically shut itself off after the 20-minute dry run.

4. Your stove is designed to burn Wood Pellets only. Burning pea coal, cherry pits, or anything

other than wood pellets will void your warranty. Pellets with high ash content will burn dirty and

require the unit to be cleaned more often. This unit is designed for use with ¼” diameter pellet

fuel. Using pellets longer than 2” can bind the auger and require frequent manual removal.

5. Be sure your pellets are not damp or wet. Keep sawdust out of the unit.

6. Use three-inch (3”) U.L.-approved (ULC if Canada) PELLET VENT TWIST-LOCK PIPE when

installing this stove and follow the manufacturer’s specifications for installation and clearances

(we highly recommend Dura-Vent pellet twist-lock pipe) (AC-3000 kit, AC-33000 if Canada). For

installations over 4000 ft. above sea level the exhaust should be vented with 4"pellet vent pipe

(AC-3100 kit, AC-33100 if Canada). Even though this pipe interlocks, it is a good idea to seal all

connections with high temperature silicone (AC-RTV3). Use at least three screws to secure the

pipe to this unit’s exhaust blower. Also, if you do not use U.L.-approved twist-lock pellet pipe, be

sure to use U.L.-approved Pellet Vent pipe, and fasten each joint of the pipe with at least three

screws (ULC-approved if Canada).

Outside combustion air is mandatory for these units to work properly. Make this connection using a 1

” I.D.

metal pipe (steel, aluminum or copper) and coupler. Be sure to secure the pipe to the unit with a clamp or

aluminum tape. The outside end should be covered (screened) to prevent any foreign matter from entering

the system. Try to keep the number of bends in this pipe to a minimum. Our Part Number PU-OAK (Outside

Air Kit with flex pipe) can be used.

NOTE:

If an older unit, measure the opening to determine what size pipe to use.

NOTE: If the total run of the intake air connection exceeds 6’, use 3” metal pipe and coupler instead.

7. Regularly inspect the burn pot area and, if any crust forms, remove it with a poker.

8. The ash in the burn pot should be removed regularly, depending on your burn rate. The area to

the right and left of the burn pot is for ash storage; keep the air holes in the burn pot clean for a

more efficient burn. Check your exhaust system frequently. Refer to “Ash Removal and

Disposal” section.

9. Keep pellets and all other combustible materials a safe distance from the unit.

10. This unit will require floor protection if installed on a combustible surface. The minimum floor

protector should give at least one inch (1”) of protection at the rear, four inches (4”) on each side,

and six inches (6”) minimum in the front of the unit.

11. Horizontal runs should not exceed four feet (4’) with a maximum vertical flue height of thirty five

feet (35’). At fifteen feet (15’), the pipe should be increased to four inch (4”) pellet vent pipe.

12. This unit should be turned off and allowed to cool prior to cleaning. Any ashes should be kept in

an airtight metal container and not disposed of until they are completely cooled.

13. Read the instructions thoroughly, including instructions concerning the digital control board, and

save them for future reference.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

14. Do not allow paint, chemicals or construction dust on or near your unit. Do not allow liquid or

ANY foreign materials on or inside your unit. Shut your unit down and cover it when painting,

construction or similar activity is taking place. Wipe and clean your unit after any construction is

done in your home, or if any foreign material gets on or inside your unit. You may also need to

remove the rear and side cover plates to your unit (unplug unit first) and vacuum and clean the

motors and inside of your unit.

15. Improper gasket maintenance, including failure to replace gaskets, can cause air leaks resulting

in smoke-backs. See Gaskets section of this manual, page 19.

16. Remember that, as with any appliance, there is user responsibility involved, including installation,

operation and maintenance of this product. Be sure to check local codes, and call Technical

Support at (800) 245-6489 if you have any questions.

17. Be sure to follow the directions of all manufacturers of third party products that you use,

including exhaust pipe, etc. Never use gasoline, lantern fuel, charcoal lighter fluid, diesel

fuel or any other flammable liquid to start the fire. If you manually start your unit,

recommended fire starter materials are: Wax-impregnated wood chips, cardboard cubes

or firestarter chips designed for pellet stoves (see section on Manually Starting Unit).

Follow any manufacturer’s directions for these products, and NEVER place any firestarter

on any hot surface or hot coals. Never apply any firestarter products of any kind to a hot

surface or hot coals.

18. Basement Installation: We recommend basement installation be performed only by a

professional installer. For basement installations, a 3” (three inch) pipe and coupler must be

used for Outside Combustion Air, and a minimum clearance of 3’ (three feet) must be maintained

from the ground to the pellet vent exhaust pipe outside the dwelling. Keep in mind that each

elbow used reduces draft by 15%; it is good practice to add 3’ (three feet) of vertical rise for each

elbow used. Example: After the 2

elbow used, have 6’ (six feet) of vertical rise before

terminating your vent pipe.

UNIT PREPARATION

1. Attach the spring handle to the door by turning it counterclockwise.

Important: Also check hopper latches – must be tight so that the top is sealed to prevent

back-burn.

2. Test your 110-volt outlet for current and then plug in the unit. (We highly recommend a surge

protector for our pellet unit, as the control panel is electronic).

3. It is important to note that this stove is equipped with a dual auger system. The top auger runs

intermittently and drops pellets to the bottom auger; the bottom auger runs constantly and simply

pushes the pellets forward to the burn pot. The control board (“Heat Range”) setting determines

the top auger feed rate.

4. The stove has a digital read-out control board and is started by pressing the “ON” touch pad. This

will start the upper auger, bottom auger and exhaust blower. The room air blower will start later

as the stove reaches the pre-set blower temperature (see “Control Board” section for further

explanation).

5. Check to be sure both augers and the exhaust blower are operating before connecting the unit to

the flue system. Be sure to “dry run” your unit for 20 minutes before connecting it to the flue (it

should stop automatically after 20 minutes).

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

FLUE SYSTEM

Caution: Follow the pipe manufacturer’s installation instructions and directions for passing

through combustible walls and ceilings. Be sure to check local codes in your area.

NOTE: See the installation drawing later in this manual (Illustration 1).

This unit is equipped with a negative draft system that pulls combustion air through the burn pot

and pushes the exhaust air out of the dwelling. If this unit is connected to the flue system other than

the way explained in this manual, it will not function properly.

For any of these installations, keep in mind that each elbow used reduces draft by 15%; it is good

practice to add 3’ (three feet) of vertical rise for each elbow used. Example: After the 2

elbow

used, have 6’ (six feet) of vertical rise before terminating your vent pipe.

Pellet Vent Pipe

The UL approved (ULC if Canada) pellet vent pipe that we recommend is a twist lock system;

however, it is still recommended that high temperature silicone (AC-RTV3) be used at each joint.

England’s Stove Works recommends the use of Dura-Vent twist-lock pipe (AC-3000 kit, AC-33000

if Canada) - if you use other pipe, consult your local building codes and/or building inspectors, and

secure each joint with at least three screws—see Important Information, above. Do not use “B” vent

gas pipe or galvanized pipe with this unit. The pellet pipe is designed to disassemble for cleaning

and should be checked several times during the burning season — pellet vent pipe is not furnished

with the unit and must be purchased separately. For installations over 4000 ft. above sea level the

exhaust should be vented with 4"pellet vent pipe (AC-3100 kit, AC-33100 if Canada). Do not

install a flue damper of any kind in this system, and do not connect this unit to a flue system

serving another heating appliance.

Through the Wall

To vent the unit through the wall, connect the pipe adapter to the exhaust motor adapter. If the

exhaust adapter is at least eighteen inches (18”) above ground level, a straight section of pellet pipe

can be used to initially pass through the wall (see Illustration 1). Your dealer or our factory should

be able to provide you with a kit that will handle most of this installation, which will include a wall

thimble that will allow the proper clearances through a combustible wall. Once outside the structure,

a three-inch (3”) clearance should be maintained to the outside wall and a clean out tee should be

placed on the pipe that extends through the wall. We recommend a minimum of three feet (3’) of

vertical pipe with a 90-degree turn away from the house. At this point, a one-foot (1’) section and

horizontal cap will complete the installation (see Illustration 1).

A wall strap should be placed just below the last 90-degree section to make the system more

stable. If you live in an area that has heavy snowfall, it is recommended the installation be taller than

three feet (3’) to get above the snowdrift line.

The same type installation can be used if your stove is below ground level by adding the clean-out

section and vertical pipe inside until ground level is reached. However, we recommend basement

installation be performed only by a professional installer. For basement installations, a 3” (three

inch) pipe and coupler must be used for Outside Combustion Air, and a minimum clearance of 3’

(three feet) must be maintained outside the dwelling from the ground to the Pellet Vent Exhaust Pipe.

IMPORTANT NOTICE: This unit must be properly installed to prevent the possibility

of a house fire or “smoke-back.” The instructions must be strictly adhered to.

Do not use makeshift methods or material which may compromise the installation.

Your unit requires periodic maintenance and cleaning (refer to manual). Failure to

maintain your unit may lead to a variety of problems, including but not limited to

smoke spillage into the home. England’s will not be liable for consequential or

indirect damages to property or persons resulting from the use of this product.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

The through-the-wall installation is the least expensive and simplest installation. In a

through-the-wall installation you should be mindful of the snowdrift line, as well as dead

grass and leaves. We recommend a three foot (3’) minimum vertical rise on the inside or the

outside of the dwelling.

Through the Ceiling

When venting the stove through the ceiling, the pipe is connected the same as through the wall,

except the clean out tee is always on the inside of the house, and a 3” adapter is added before the

clean-out tee. You must use the proper ceiling support flanges and roof flashing supplied by the pipe

manufacturer -- follow the pipe manufacturer’s directions and Illustration 1 in this manual.

It is

important to note that if your vertical runs of pipe are more than fifteen feet (15’), the pellet vent pipe

should be increased to four inches (4”) in diameter. Do not exceed four feet (4’) of pipe on a

horizontal run, and do attempt to use the least number of elbows in the flue system. If an offset is

used it is better to install a 45-degree elbow whenever possible. NOTE: Installing elbows may inhibit

your draft by up to 15% per elbow.

Existing Flue System

If you are replacing a wood stove with a pellet unit the chimney or pipe should be thoroughly

cleaned before proceeding with the installation. If connecting this stove to a factory built chimney, it

may ONLY be a 6” flue, UL103 HT venting system (ULC S629 if Canada). Connection to any other

factory built chimney may result in a poorly operating or dangerous stove installation. When

connecting to an existing masonry chimney, the cross-sectional area of the flue must be considered.

A chimney with a flue larger than 6” round (28.27 sq. in.) may require relining with an approved pellet

stove chimney lining system. Make sure the chimney meets the minimum standards listed in NFPA

211 (A chimney professional can confirm this upon inspection).

Outside Air (Outside Combustion Air Intake)

Outside air is mandatory for this unit to operate properly

. This unit has been designed and tested

with this connection, because so many homes are airtight and there is not adequate combustion air

available inside the dwelling. The air intake pipe is located on the bottom side of the burn pot (from

the rear) and measures 1 ½” inside diameter (I.D.). The connection can be made with a metal 1

”

I.D. coupler and pipe (see “Important Information” section of manual), and should exit through the

wall. Be sure to secure the pipe to the unit with a clamp or aluminum tape. The outside end of the

pipe should be covered (screened) to prevent foreign matter from entering the system.

Our Outside

Air Kit (Part Number PU-OAK) can be used.

If the unit is located below ground level, you will need to

run the pipe up and then outside the dwelling. NOTE: If the total run of the connection exceeds 6’, if

more than 2 elbows are used, or if a basement installation, use 3” metal pipe (and coupler) instead.

Note

: If an older unit, measure the opening to determine what size pipe to use or couple to.

Mobile Home Installation

Secure the heater to the floor using the two holes in the pedestal. If the unit is on a combustible

surface, you will need to drill matching holes in the floor protection that you choose (see Floor

Protection section). Do not disturb the structural integrity of the home, be sure the unit is

permanently electrically grounded to the chassis of your home and remember that outside

combustion air is mandatory.

IMPROPER INSTALLATION: The manufacturer will not be held responsible for damage caused by the

malfunction of a stove due to improper venting or installation.

Call 800-245-6489 and/or consult a professional installer if you have any questions.

IMPORTANT: Improper hook-up (too much pipe, too many elbows, etc.) will cause the unit not to operate.

Call Technical Support (800-245-6489) if you have questions about your hook-up or if your unit will not

erate.

WARNING: DO NOT INSTALL IN SLEEPING ROOM

CAUTION

: THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL AND

CEILING/ROOF MUST BE MAINTAINED.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

FLOOR AND WALL PROTECTION

Floor Protection

If your floor is constructed of a non-combustible material such as brick or concrete, there is no need

for floor protection. If the floor is constructed of a combustible material such as hardwood, linoleum, or

carpet, then you will be required to use floor protection between the unit and the combustible. The

protection should be U.L. approved or equivalent (ULC if Canada) and must be large enough to provide a

minimum of one inch (1.0”) behind, four inches (4.0”) on both sides of the stove and at least six inches

(6.0”) in the front of the unit. This floor protection is intended as spark and ember protection only,

therefore it need only be noncombustible (there is no required R value).

Wall Protection

From the rear and the sides of this stove only six inches (6”) of clearance is required to paneling, wallpaper

or drywall. The pellet vent pipe usually requires the standard three inches (3”) of clearance, or as

recommended by the manufacturer. Normally additional wall protection is not required with this type unit.

1. If 3” flue pipe exceeds 15’ in length, increase to 4” flue pipe for remaining flue connections.

2. Total flue length should not exceed 35’.

3. Horizontal run not to exceed 4’.

4. Floor protector must extend 6” from front of unit, 4” from sides and 1” from rear.

5. If the total run of outside air connection exceeds 6’, if more than 2 elbows are used, or if a

basement install, use 3” metal pipe (and coupler) instead.

6. Outside Air is mandator

er sa

e o

eration.

Masonr

Connection

Illustration 1

Freestanding Pellet Installation

Caution: Follow the pipe manufacturer’s installation instructions and directions for

passin

throu

h combustible walls and ceilin

s. Check local codes in

our area.

Our Part AC-3000 is

acceptable for

through-the-wall

installation;

AC-3100 for 4000+

ft. installations.

(AC-33000 or AC-

33100 if Canada)

Must have minimum

3” adapter before tee

for longer run.

For shorter run

(such as Masonry

Connection below),

tee alone is

acceptable.

Basement Installation should

be performed by

professional installer. Use

3” metal pipe and coupler

for Outside Combustion Air.

Minimum 3 feet (3’)

clearance from ground to the

Pellet Vent Exhaust Pi

INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

VENT TERMINATION CLEARANCES

A) MIN. 4-FT CLEARANCE BELOW OR BESIDE ANY DOOR OR WINDOW THAT OPENS.

B) MIN. 1-FT CLEARANCE ABOVE ANY DOOR OR WINDOW THAT OPENS.

C) MIN. 2-FT CLEARANCE FROM ANY ADJACENT BUILDING.

D) MIN. 7-FT CLEARANCE FROM ANY GRADE WHEN ADJACENT TO PUBLIC

WALKWAYS.

E) MIN. 2-FT CLEARANCE ABOVE ANY GRASS, PLANTS, OR OTHER COMBUSTIBLE

MATERIALS.

F) MIN. 3-FT CLEARANCE FROM A FORCED AIR INTAKE OF ANY APPLIANCE.

G) MIN. 2-FT CLEARANCE BELOW EAVES OR OVERHANG.

H) MIN. 1-FT CLEARANCE HORIZONTALLY FROM COMBUSTIBLE WALL.

I) MUST BE A MINIMUM OF 36-INCHES ABOVE THE ROOF AND 24-INCHES ABOVE THE

HIGHEST POINT OF THE ROOF WITHIN 10-FEET.



Notes on termination of Pellet Vent Pipe from NFPA211(2006ed.)Section10.4Termination:10.4.5

(See also “FLUE SYSTEM” section of manual AND additional notes above):

- Not less than three (3) feet above any forced air inlet located within ten (10) feet.

- Not less than four (4) feet below, four (4) feet horizontally from, or one (1) foot above any door,

window or gravity air inlet into any building.

- Not less than two (2) feet from an adjacent building, and not less than seven (7) feet above grade

where located adjacent to public walkways.

The exhaust exit shall be arranged so that the flue gases are not directed so that it will affect people, overheat

combustible structures, or enter buildings. Forced draft systems and all parts of induced draft systems under

positive pressure during operation shall be installed gastight or to prevent leakage of combustion products into

a building. Through-the-wall vents shall not terminate over public walkways, or where condensate or vapor

could create hazards or a nuisance.

Be sure to follow local codes and all manufacturer’s instructions (including exhaust pipe).

Consult a professional installer and/or call Technical Support if you have any questions.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

OPERATING INSTRUCTIONS

CAUTION: DO NOT OPERATE WITH THE DOOR OPEN.

If door is left open (approximately) two minutes, unit will stop feeding and fire will go out.

Do not burn trash (paper bags, etc.) in this unit.

This stove has an induced draft system and is designed to operate continuously, as frequent

shutdown is not required. The digital control board operates the unit with a time delay-relay system;

this system controls the top auger feed rate by operating for a predetermined number of seconds

while the bottom auger runs constantly. The setting of the “Heat Range” touch pad will control the

heat output and the amount of pellets the unit will burn (see “Control Board” section and

Illustration 3). Note: This stove is using solid fuel and will not restart automatically.

* NOTE: Blower Speed will automatically be adjusted to the desired Heat Range that you select.

Horizontal Feed System

This unit has a top and a bottom auger that are separated by four inches (4”); a 1-RPM motor

drives each auger. The top auger intermittently drops pellets to the bottom auger tube, and the

bottom auger pushes the pellets forward to the burn pot. This helps prevent build-up of fuel in the

bottom auger tube. As pellets enter the burn pot the combustion air is drawn across the fuel.

START- UP PROCEDURE

Caution - Never use gasoline, lantern fuel, charcoal lighter fluid, diesel fuel, or any other

flammable liquid to start the fire.

1. Be sure the hopper is clean and free from foreign materials. Be sure there is current at your

outlet (we do recommend a surge protector with our unit).

2. Before your first fire dry run your unit (with no pellets in the hopper) for 20 minutes. Press

the “ON” button to begin the dry run. After the 20 minute dry run, the control board will return

to “OFF.” An error code will appear in the Heat Range and the Blower Speed windows as

“E-2,” which means the unit failed to start normally. After this code is received and you are sure

the unit is working properly, fill the hopper with wood pellets. Do not allow any part of the bag

or any foreign material in the hopper, as this may jam the augers. Ensure that all pellet matter

is cleared from the hopper lid gasket, make sure the hopper lid latches and the door of the unit

are securely closed and press the “ON” button; this will clear the error code and restart your

unit.

Automatic Start-Up

When the “ON” button is pressed from a cold start, the unit is in “Start-Up” (after 3 seconds, there

will be an “S U” in the Heat Range and Blower Speed windows to verify this). While in this mode,

the unit has a preset heat range and will remain in this mode for 20 minutes to prevent the unit

from over-firing. During this start-up period you can set the Control Board at the setting you

desire; after the start-up is complete, the unit will operate at the user setting.

Manually Starting Your Unit

In the event the Auto-Start does not initiate, you may manually start your unit. To manually start

your unit, first clean any pellets out of the burn pot (to prevent over-feeding). Place a handful of

new pellets in the burn pot, then spread a small amount of pellet fire starter over the pellets and

ignite them. After the pellets ignite, close the door to your unit and press the “ON” button (if the

door is closed before the pellets fully ignite, the Exhaust Blower could put out the fire).

Recommended fire starter materials: Wax-impregnated wood chips, cardboard cubes or

firestarter chips designed for pellet stoves. Follow any manufacturer’s directions for these

products, and NEVER place any firestarter on any hot surface or hot coals. Never use gasoline,

lantern fuel, kerosene, charcoal lighter fluid, diesel fuel or any other flammable liquid to start the

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

fire. Do not use the manual startup method if the igniter is working. NEVER place firestarter

near the igniter.

If you have continued problems with the Auto-Start Igniter, call Technical Support.

E-Codes

“E-Codes,” or Error Codes, are codes that will appear in the Heat Range and Blower Speed

windows of the Control Board if your unit experiences problems. If you receive any of these codes,

first attempt to reset your unit by pressing the “ON” button (only once). If the unit continues to

display any E-Code(s), please contact Technical Support at (800) 245-6489 before further attempting

to restart your unit.

1. E-1 = Vacuum Loss

2. E-2 = Fail to Start

3. E-3 = Over Temperature Limit

NOTE: “E-0” indicates “No Error”

First Fire: Adjust the “Heat Range” to a “5” setting and allow the stove to burn in this manner

for at least three (3) hours. This will allow the unit to “cure out” as the paint and the

oils from the manufacturing process burn off. We recommend you open doors and

windows in your dwelling during this process.

Subsequent Cold Starts: In a cold start situation, the unit should be operated at a “5” setting

until the room air blower begins to operate.

NOTE: The start-up cycle for this unit with the Auto-Start Igniter is 13 minutes. Press the

“ON” button only once on start-up. Pressing the “ON” button a second time during

the start-up cycle will cause the start-up cycle to begin again.

IMPORTANT: If the unit fails to start properly, or does not properly complete the Shut-Down

procedure, open the closest outside door and a window to eliminate the home’s

natural draft BEFORE opening the stove’s door or hopper lid. This will allow

any smoke to exit through the external air hook-up instead of spilling into the home.

SHUT-DOWN PROCEDURE

WARNING: NEVER SHUT DOWN THIS UNIT BY UNPLUGGING IT FROM THE POWER SOURCE.

Refer to the following instructions:

Press the “OFF” touch pad to put the stove in the “Shut-Down” mode. There will be an

“S D” in the Heat Range and Blower Speed windows while the unit is shutting down to verify this. At

this time the red light above the “OFF” pad will illuminate. When the “OFF” pad is touched the top

auger will instantly stop feeding pellets to the bottom auger tube, but the room air blower, exhaust

blower and bottom auger will continue to operate. When the internal temperature drops to 95

degrees the room air blower will cease to operate, and when the internal temperature drops to 90

degrees the bottom auger and exhaust blower will stop. The red light will then shut off and the entire

stove will be shut down. The hotter the unit is operating, the longer it will take for the stove to

complete the Shut-Down cycle.

Note: The unit will exit the Shut-Down cycle if you press any buttons during Shut-Down.

Note: If the room temperature stays above 70 degrees the stove will remain in the Shut Down mode

for 60 minutes, regardless of the temperature reading at the heat sensor. If the stove stays on

longer than 60 minutes the unit will automatically turn off.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

DAILY OPERATION

Refueling the Unit

Always press the “OFF” touch pad before refueling. This unit has a 40-lb. hopper, and should be

refilled when the hopper level drops to three or four inches.

Note: The hopper lid will be warm; therefore, you should always use some type of hand protection.

NEVER place your hand near the auger while the stove is operating.

Note: Always ensure that all pellet matter is cleared from the hopper lid gasket before closing. Be

sure to close and latch hopper securely before re-firing. Do not operate this unit with the

hopper lid open or unsecured.

Power Outage

If the power to the unit is interrupted for approximately three minutes or less, the unit will resume

operation when power is restored according to the following table:

Unit’s State Before Power Loss State When Power Returns

ON Start-Up

Start-Up Start-Up

Shut-Down Shut-Down

OFF OFF

If the power is interrupted for more than (approximately) three minutes, the unit will be “OFF”

when power returns.

Important: Do NOT open the hopper lid or the door to the unit during power outage. Open

the closest outside door and a window to eliminate the home’s natural draft. Wait

for power to be restored and then press the “ON” button to re-start the unit, if necessary.

We highly recommend the use of a surge protector with your unit, as power surges and failures

can affect the operation of any electrical appliance.

We do not recommend leaving home with the stove on the higher heat ranges; it is

recommended that the stove be left on the lower heat ranges (Heat Range setting 1 or 2).

NOTE: Remember: 1) It is very important for the unit to be vented properly (see instructions on

Outside Air), as the natural draft is needed to clear the smoke from the stove. 2) Do not

open the hopper lid (or the unit’s door). This may cause fire to burn in the hopper.

Fuel Outage

If the unit should run out of pellets, simply reload the hopper and press the “ON” button (only

once) to re-start the unit. If the unit runs without pellets, after one hour the unit will shut down.

NOTE: Even if flames are visible inside the fire box always

press the “ON” button to ensure that

your unit will restart.

Combustion Blower Failure

If the Combustion (exhaust) Blower should fail on this unit, a Vacuum Shut-Down Switch will

automatically stop the stove. This will shut your unit completely off, and there will be an “E-1” code in

the Heat Range and Blower Speed windows on the Control Board. At this point you will need to

contact Technical Support at (800) 245-6489.

NOTE: It is very important for the unit to be vented properly (see instructions on Outside Air), as the

natural draft is needed to clear the smoke from the stove.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

ASH REMOVAL AND DISPOSAL

IMPORTANT: While the amount of ash generated by this unit is not excessive compared to

log-burning woodstoves, keeping the unit clean and free of ash is essential

for

peak performance. Too much ash build-up hampers airflow and reduces the

unit’s efficiency, and can cause smoke-back. Follow these directions at least

as frequently as the schedule below, or more often if needed.

Daily Ash Maintenance

Press the “OFF” touch pad and allow the stove to burn for five (5) minutes prior to opening the

door. A long-handled screwdriver or long-handled putty knife can be used to scrape off any build-up

or crust in the burn pot area. This can then be pushed to the left or right into the ash storage area.

Semi-Weekly Ash Removal

Twice each week: Shut the unit down by

pressing the “OFF” pad and allowing the unit to go

through the complete Shut-Down cycle. Allow the

unit to completely cool down and then remove the

ashes with a scoop. The ashes should be placed

in a non-combustible container with an airtight lid

and should always be placed on a non-combustible

surface or on the ground until completely cooled

and free of hot cinders.

Once the ash is removed, the burn pot should

be given a thorough inspection. Remove and

clean the burn pot wear plate (refer to the exploded

diagram in the rear of this manual – Illustration 6,

and the close-up diagram shown here), and

remove any ash build-up in the area below the

wear plate. Also, be sure there are no ashes or

obstructions in the tube under the wear plate. Check for any build-up in the front of the burn area.

Clean out all air holes (if necessary a 1/8” drill bit can be used) --these air holes should be kept

clean, as they supply combustion air under and around the pellet fuel. The burn pot assembly

should also be thoroughly cleaned, including the burn box. When replacing the wear plate, ensure

that it lies flat in the firebox and no gaps (from ash residue) are under it.

IMPORTANT: Ash build-up under the wear plate can cause the unit to malfunction.

Illustration 2

Bottom Auger Tube

NOTE: The instructions below concerning the cleaning of the burn pot and wear plate area are especially

important to the function of your stove. Failure to follow them regularly can result in burn-back

and can damage your unit and/or void your warranty.

Disposal of Ashes

Ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes should

be placed on a noncombustible floor or on the ground, well away from all combustible materials, pending

final disposal. If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be

retained in the closed container until all cinders have been thoroughly cooled.

As with any maintenance concerning this unit, be sure the unit is “OFF” and has completed the Shut-

Down cycle BEFORE beginning. Be aware that metal parts in the firebox can remain HOT long after

the fire has gone out and EVEN after the Shut-Down cycle is complete. Always use extreme caution

when handlin

potentiall

hot stove parts, even if

ou think the

should be cold.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

Monthly Ash Removal

The large baffle plate (12” x 13”) that rests above and behind the burn pot (refer to the exploded

diagram in the rear of this manual – Illustration 6) should be removed monthly. This can be done by

lifting up the plate and pulling it out. The area behind the plate should then be cleaned thoroughly,

and the plate placed back in the original position.

Use a screwdriver or chisel and break any creosote build-up in the front of the unit, where the

pellets are fed into the burn pot from the Bottom Auger Tube (see Illustration 2). Moisture in the

pellets and resulting build-up in this area can cause the bottom auger to “squeal” or squeak.

Also inspect your flue pipes, and remove ash buildup from the clean-out tee.

Carbon Removal: During normal operation carbon from the combustion of pellet fuel will tend to

build up on the tip of the auger, on the wear plate and sides of the fire pot, and in the mouth of the

feed tube. It is essential that this residue be removed to ensure trouble free operation of the unit. The

frequency with which this carbon must be removed varies with brands of pellets, depending on

moisture content, wood type, foreign material (dirt, etc.) in pellets, and other factors.

To remove this carbon, simply scrape it off using the blade of a flat tipped screwdriver or similar

instrument; also, to remove it from the feed tube, scrape as much as can be easily reached, then

insert an emery board (fingernail file made from a popsicle stick and sandpaper) between the feed

auger and the feed tube and sand out any residue not removed from scraping alone. Clearing this

carbon residue from the feed tube is essential for proper operation of the feed auger, which is

designed to float freely in the feed tube allowing smooth fuel flow, a lesser possibility of a jam, and a

quieter unit.

Annual Cleaning

The stove and the flue system should be given a complete cleaning at the end of the heating

season. Remove the burn pot assembly, clean it thoroughly, and re-install it (refer to Illustration 6);

this will require new gasket for the burn pot. Be sure to tighten the set screws when you replace

them, but do not over-tighten. In addition to the cleaning mentioned for semi-weekly and monthly,

the Combustion (exhaust) Blower should be removed annually and the blower tube vacuumed of any

ash build-up. Note: There is a Combustion Motor Gasket (Part PU-CMG), which allows you to

remove the motor from the Combustion Blower housing, clean your stove, and replace the motor and

gasket without having to remove the entire Combustion Blower. However, if you must remove or

replace the entire Combustion Blower, a new blower flange gasket (Part # PU-CBG) should be

added between the blower flange and the steel exhaust tube.

Soot and Fly ash: Formation and Need for Removal – The products of combustion will contain

small particles of fly ash. The fly ash will collect in the exhaust venting system and restrict the flow of

flue gases. Incomplete combustion, such as occurs during startup, shutdown, or incorrect operation

of the room heater will lead to some soot formation which will collect in the exhaust venting system.

The exhaust venting system should be inspected at least once every year to determine if cleaning is

necessary.

Soot and Fly Ash: Formation and Need for Removal

The products of combustion will contain small particles of fly ash. The fly ash will collect in the

exhaust venting system and restrict the flow of the flue gases. Incomplete combustion, such as that

which occurs during startup, shutdown or incorrect operation of the room heater will lead to some

soot formation which will collect in the exhaust venting system. The exhaust venting system should

be inspected at least once every year to determine if cleaning is necessary.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

MAINTENANCE

CAUTION: UNPLUG THE UNIT PRIOR TO ANY SERVICE WORK!

SEE EXPLODED DIAGRAM (ILLUSTRATION 6) FOR PARTS REFERENCE

Parts Orders: (800) 516-3636 www.englanderstoves.com Questions: (800) 245-6489

NOTE: Visit our web site for downloadable maintenance sheets and/or a service video that details

and illustrates the following maintenance tasks.

Rear Panel Removal

WARNING: To perform any maintenance inside the rear of the unit, the stove must be out (no

fire), cooled down and unplugged. Electrical shock can occur if the unit is not

unplugged from power.

To remove the rear panel, simply loosen the eight (8) screws (size 5/16”) and flex the panel. The

panel should come off without fully removing the screws.

Instructions for maintenance and part replacement procedures can be found on:

www.englanderstoves.com

Auger Motors

The Auger Motor and gearbox are one complete assembly (Part # PU-047040), and can be

removed by disconnecting the power leads and loosening the (

” head) set bolt in front of the

assembly. This bolt tightens down on the flat side of the gear shaft and locks the gear shaft and

auger shaft together – once the bolt is loosened, the entire assembly will slide from the locking collar.

There are two motor assemblies on the unit, and both rest on a shelf when not in operation. When

replacing a motor, the assembly should always be placed to rest on this shelf prior to starting the

unit.

Auger Bearings and Auger Shafts

The auger bearings (Part # PU-UCF204-12) are a sealed unit and do not require lubrication

. To

replace the Top Auger, all the fuel must be removed from the hopper as well as from the Top Auger

assembly. Once this is done, the four bolts that hold in the bearing can be removed, followed by the

complete auger assembly. Loosen the two (2) set screws with a 1/8” Allen wrench, which will

disconnect the bearing from the shaft (the bearing assembly and auger assembly can be replaced by

reversing this procedure). When placing the auger assemblies in the unit, always tighten the four

bolts in a diagonal pattern to ensure the bearings and shafts are aligned properly.

NOTE: Follow the same procedure to work on the bottom auger, with the exception that the pellets

do not have to be removed from the hopper.

Convection Blower

The Convection (room air) Blower (Part # PU-4C442) is located on the left side of the unit and

can be removed by disconnecting the power leads and removing the four mounting screws. Once

this is done, the blower will slide out of the stove. This procedure can be reversed to install a new

blower.

Combustion Blower

To replace the Combustion (exhaust) Blower (Part # PU-076002B), the power leads and the

pellet vent pipe must be disconnected. Next, remove the screws that hold the blower to the steel

exhaust tube and slide the blower from the stove. Note: There is a Combustion Motor Gasket

(Part # PU-CMG), which allows you to remove the motor from the Combustion Blower housing, clean

your stove, and replace the motor and gasket without having to remove the entire Combustion

Blower. If cleaning your blower, the blower impeller, blower tube and steel blower exhaust tube on

the unit should be brushed and vacuumed. However, if you must remove or replace the entire

Combustion Blower, a new blower flange gasket (Part # PU-CBG) should be added between the

blower flange and the steel exhaust tube.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

Vacuum Switch

This unit is equipped with Vacuum Shut Down Switches (Part # PU-VS and CU-VS), which help

control various functions of the unit. If an operational error occurs in the unit, a switch will either stop

the top (feed) auger or shut the unit off; if the unit turns off an E-1 Code (error code) will appear in

the Heat Range and Blower Speed windows of the Control Board. Situations which could cause this

include power failure, Combustion Blower failure, improper flue installation, a blocked flue (from

rodents, nests, etc.), or “dirty burning” from burning improper fuel (see “Important Information” at the

beginning of the manual).

“Door Ajar” Vacuum Switch Port

NOTE: The "door ajar" vacuum switch port must be kept clean, or the top auger will cease to function.

Locate the port hole to the right of the burn pot and, with the stove unplugged and cooled down, use a

brush or pipe cleaner (not a vacuum) to keep this port clear of ash or other debris (see picture).

Port is located to the right

of the burn pot

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

Hopper Lid Safety Switch

This unit is equipped with a hopper lid safety switch (Part # AC-HLSB) which is directly

connected to the top auger motor. In the event the hopper lid is left open while the stove is in

operation, the hopper lid switch will prevent the top auger from turning. This is to prevent byproducts

of combustion from entering the home through the open hopper lid and also to simply prevent

operation with the hopper lid open.

Improper hopper lid safety switch operation will result in a top auger that will not turn and

therefore a stove that will not burn. NEVER place your hand or any object near the auger while the

stove is connected to power.

Gaskets

IMPORTANT: IMPROPER GASKET MAINTENANCE, INCLUDING FAILURE TO REPLACE

GASKETS, CAN CAUSE AIR LEAKS RESULTING IN SMOKE-BACKS. CHECK

GASKETS OFTEN FOR AIRTIGHT SEAL AND REPLACE AS NECESSARY. IT IS

MANDATORY TO REPLACE GASKETS ANNUALLY.

This unit comes with a 3/4” rope gasket around the door that should be replaced annually. To

replace the door gasket (Part # AC-DGKC), the old gasket must first be removed entirely — prior to

adding the new adhesive, you may have to scrape the old cement from the door channel. Once the

cement and gasket have been added, the door should be closed and latched for twenty-four hours to

allow the cement to harden.

If you are replacing the window gasket (Part # AC-GGK), the new gasket will already have

adhesive on one side. Remove the paper on the adhesive side and place the gasket around the

outside edge of the glass by forming a “U” with your fingers and placing the gasket around the glass.

It is important to change the hopper lid gasket if it shows any wear. Be sure to replace the hopper

lid gasket annually, or sooner if necessary.

Note: There is a Combustion Motor Gasket (Part # PU-CMG), which allows you to remove the

motor from the Combustion Blower housing, clean your stove, and replace the motor and gasket

without having to remove the entire Combustion Blower. However, if you must remove or replace the

entire Combustion Blower, a new blower flange gasket (Part # PU-CBG) should be added between

the blower flange and the steel exhaust tube.

Finish

This new unit has been painted with High-Temperature Paint that should retain its original look

for years. If the unit should get wet and rust spots appear, the spots can be sanded with plain steel

wool and repainted. We recommend this paint, as others may not adhere to the surface or withstand

the high temperatures.

Glass

This unit has a 9” x 9” ceramic glass (Part # AC-G9, comes with gasket) in the viewing door.

Surface scratches are acceptable and normal, but if this glass becomes cracked in any area, the unit

should be shut down and the window replaced with this high-temperature ceramic glass.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY QUESTIONS.

Control Board

The Control Board (Part # PU-CB04) is a digital read-out board. This board offers a wide variety

of settings to operate the unit. This part can be removed from the unit by loosening the two outside

screws and pulling the board back to the inside of the stove. The rear access panel should be

removed prior to removing the control board. A 6-amp “quick-blow” fuse (Part # PU-CBF6) is used

on this Control Board.

NOTE: The bottom three control buttons are preset at the factory and should not require any

changes. See “Operating Instructions” and “Daily Operation” section of the manual for

instructions on other Control Board settings.

Recommended Heat Ranges:

Low Burn: Heat Range setting: 1 Room Air Blower setting: 1

Medium Low: Heat Range setting: 2 – 3 Room Air Blower setting: *

Medium High: Heat Range setting: 5 – 8 Room Air Blower setting: *

High Burn: Heat Range setting: 9 Room Air Blower setting: 9

* NOTE: Blower Speed should match the Heat Range setting.

NOTE: The bottom

3 buttons are pre-set at

the factory and do not

need adjustment.

Call Service at

(800) 245-6489 if you

have questions or

problems.

CAUTION:

Illustration 3

Control Board

Diagram

Caution

Should you see any evidence of smoke in the hopper (smoke back),

immediately close and latch the hopper lid and door to the unit. Open the

nearest windows and door to the outside, then press the OFF button and let

the unit cool for at least 3 hours. Do not open the door or hopper lid. This

is a maintenance problem that needs to be addressed.

Call Technical Support at (800) 245-6489

La page charge ...

England's Stove Works 25-PDVC Installation & Operation Manual

Marque: England's Stove Works

Modèle: 25-PDVC

Catégorie: Cheminées

Taper: Installation & Operation Manual

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: England's Stove Works 25-PDVC

England's Stove Works 25-PDVC Installation & Operation Manual

Ce manuel convient également à

England's Stove Works 25-PDVC Installation & Operation Manual

dans d''autres langues

Documents connexes

Autres documents