Amana UPRIGHT FREEZER Le manuel du propriétaire

Owner’s Manual

Heavy Duty Commercial

Compact [0.6 Cubic Foot]

Microwave Oven

Keep these instructions for future reference.

If the oven changes ownership, this manual must

accompany oven.

Contents

Model Identication ........................... 2

Important safety InstructIons ... 3

precautIons to avoId possIble

exposure to excessIve

mIcrowave energy ................... 4

Grounding/Earthing Instructions ........ 5

Installation ......................................... 6

Display and Features Style 1 ............ 7

Operation Style 1 .............................. 9

Programming Style 1 ....................... 10

Options Style 1 .................................11

Display and Features Style 2 .......... 12

Operation Style 2 ............................ 13

Programming Style 2 ....................... 15

Options Style 2 ................................ 16

Care and Cleaning .......................... 17

Before Calling for Service ............... 19

2

Model Identication

When contacting ACP, provide product information.

Product information is located on oven serial plate.

Record the following information:

Model Number: _____________________________

Manufacturing Number: _______________________

Serial or S/N Number: ________________________

Date of purchase: ___________________________

Dealer’s name and address: ___________________

__________________________________________

Keep a copy of sales receipt for future reference or in

case warranty service is required.

Any questions or to locate an authorized service

agent contact ACP, Inc. ComServ Customer Service

at: Phone 866.426.2621 / 319.368.8195 or email:

[email protected]. Warranty service

must be performed by an authorized servicer. ACP also

recommends contacting an authorized servicer if service

is required after warranty expires.

3

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

9. DO NOT operate this oven if it has a damaged

cord or plug, if it is not working properly, or if it has

been damaged or dropped.

10. This oven, including power cord, must be serviced

ONLY by qualied service personnel. Special tools

are required to service oven. Contact nearest

authorized service facility for examination, repair,

or adjustment.

11. DO NOT cover or block lter or other openings

on oven.

12. DO NOT store this oven outdoors. DO NOT

use this product near water – for example, near

a kitchen sink, in a wet basement, or near a

swimming pool, and the like.

13. DO NOT immerse cord or plug in water.

14. Keep cord AWAY from HEATED surfaces.

15. DO NOT let cord hang over edge of table or

counter.

16. See door cleaning instructions in “Care and

Cleaning” section of manual on page 17.

17. For commercial use only.

When using electrical oven, basic safety precautions should be followed to reduce the risk of burns, electric shock,

re, or injury to persons or exposure to excessive microwave energy.

!

WARNING

a. DO NOT overcook food. Carefully attend oven if

paper, plastic, or other combustible materials are

placed inside the oven to facilitate cooking.

b. Remove wire twist-ties from paper or plastic bags

before placing bag in oven.

c. KEEP oven DOOR CLOSED, turn oven off, and

disconnect the power cord, or shut off power at

the fuse or circuit breaker panel, if materials inside

the oven should ignite. Fire may spread if door is

opened.

d. DO NOT use the cavity for storage. DO NOT leave

paper products, cooking utensils, or food in the

cavity when not in use.

To reduce the risk of re in the oven cavity:

!

WARNING

1. READ all instructions before using oven.

2. READ AND FOLLOW the specic “PRECAUTIONS

TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE

MICROWAVE ENERGY” on page 4.

3. This oven MUST BE GROUNDED. Connect only to

properly GROUNDED outlet. See “GROUNDING

INSTRUCTIONS” on page 7.

4. Install or locate this oven ONLY in accordance with

the installation instructions in this manual.

5. Some products such as whole eggs and sealed

containers – for example, closed glass jars – may

explode and SHOULD NOT be HEATED in this

oven.

6. Use this oven ONLY for its intended use as

described in this manual. Do not use corrosive

chemicals or vapors in this oven. This type of oven

is specically designed to heat or cook. It is not

designed for industrial or laboratory use.

7. As with any oven, CLOSE SUPERVISION is

necessary when used by CHILDREN.

8. If smoke is observed, switch off or unplug the

appliance and keep the door closed in order to stie

any ames.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

4

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

1. Briskly stir or pour liquids before cooking with

microwave energy to prevent spontaneous boiling

or eruption. Do not overheat. If air is not mixed

into a liquid, liquid can erupt in oven or after

removal from oven.

2. Do not deep fat fry in oven. Fat could overheat and

be hazardous to handle.

3. Do not cook or reheat eggs in shell or with an

unbroken yolk using microwave energy. Pressure

may build up and erupt. Pierce yolk with fork or

knife before cooking.

4. Pierce skin of potatoes, tomatoes, and similar

foods before cooking with microwave energy.

When skin is pierced, steam escapes evenly.

5. Do not operate oven without load or food in oven

cavity.

6. Use only popcorn in packages designed and

labeled for microwave use. Popping time varies

depending on oven wattage. Do not continue

to heat after popping has stopped. Popcorn will

scorch or burn. Do not leave oven unattended.

7. Do not use regular cooking thermometers in oven.

Most cooking thermometers contain mercury

and may cause an electrical arc, malfunction, or

damage to oven.

8. Do not heat baby bottles in oven.

9. Do not use metal utensils in oven.

10. Never use paper, plastic, or other combustible

materials that are not intended for cooking.

11. When cooking with paper, plastic, or other

combustible materials, follow manufacturer’s

recommendations on product use.

12. Do not use paper towels which contain nylon

or other synthetic bers. Heated synthetics could

melt and cause paper to ignite.

13. Do not heat sealed containers or plastic bags

in oven. Food or liquid could expand quickly and

cause container or bag to break. Pierce or open

container or bag before cooking.

14. To avoid pacemaker malfunction, consult

physician or pacemaker manufacture about

effects of microwave energy on pacemaker.

PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO

EXCESSIVE MICROWAVE ENERGY

a. DO NOT attempt to operate this oven with door

open since open-door operation can result in

harmful exposure to microwave energy. It is

important not to defeat or tamper with safety

interlocks.

b. DO NOT place any object between oven front

face and door or allow soil or cleaner residue to

accumulate on sealing surfaces.

c. DO NOT operate oven if it is damaged. It is

particularly important that oven door close properly

and that there is no damage to: (1) door (bent), (2)

hinges and latches (broken or loosened), (3) door

seals and sealing surfaces.

d. Oven should NOT be adjusted or repaired by

anyone except properly qualied service personnel.

To avoid personal injury or property damage, observe the following:

CAUTION

!

5

Grounding Instructions

WARNING

To avoid risk of electrical shock or death, this oven

must be grounded.

WARNING

To avoid risk of electrical shock or death, do not alter

the plug.

This oven MUST be grounded. In the event of an

electrical short circuit, grounding reduces the risk of

electric shock by providing an escape wire for the

electric current. This oven is equipped with a cord

having a grounding wire with a grounding plug. The plug

must be plugged into an outlet that is properly installed

and grounded.

Consult a qualied electrician or servicer if grounding

instructions are not completely understood, or if doubt

exists as to whether the oven is properly grounded.

Do not use an extension cord. If the product power

cord is too short, have a qualied electrician install a

three-slot receptacle. This oven should be plugged into

a separate circuit with the electrical rating as shown on

the oven’s serial plate / rating label. When a microwave

oven is on a circuit with other equipment, an increase in

cooking times may be required and fuses can be blown.

Earthing Instructions

Oven MUST be earthed. Earthing reduces risk of

electric shock by providing an escape wire for the

electric current, if an electrical short occurs. This oven is

equipped with a cord having a earth wire with a earthing

plug. The plug must be plugged into an outlet that is

properly installed and earthed.

Consult a qualied electrician or servicer if earthing

instructions are not completely understood, or if doubt

exists as to whether the oven is properly earthed.

Do not use an extension cord.

If the product power cord is too short, have a qualied

electrician install a new receptacle close enough to the

oven to plug the oven in. This oven should be plugged

into a separate circuit with the electrical rating as

provided in product specications (available on www.

acpsolutions.com). When a microwave oven is on a

circuit with other equipment, an increase in cooking

times may be required and fuses can be blown.

External Equipotential Earthing Terminal

(export only)

Equipment has secondary earthing terminal. Terminal

provides external earthing connection used in addition

to earthing prong on plug. Located on outside of oven

back, terminal is marked with symbol shown below.

6

Unpacking Oven

• Inspect oven for damage such as dents in door or

dents inside oven cavity.

• Report any dents or breakage to source of purchase

immediately. Do not attempt to use oven if damaged.

• Remove all materials from oven interior.

• If oven has been stored in extremely cold area, wait a

few hours before connecting power.

Radio Interference

Microwave operation may cause interference to radio,

television. Reduce or eliminate interference by doing the

following:

• Clean door and sealing surfaces of oven according to

instructions in “Care and Cleaning” section.

Oven Placement

• Do not install oven next to or above source of heat,

such as pizza oven or deep fat fryer. This could cause

microwave oven to operate improperly and could

shorten life of electrical parts.

• Do not block or obstruct oven lter. Allow access for

cleaning.

• Install oven on level countertop surface.

A—Allow at least 7 “ (17.8 cm) of clearance around top and

sides of oven. Proper air ow around oven cools electrical

components. With restricted air ow, oven may not operate

properly and life of electrical parts is reduced.

B—Allow at least 2

9

/16 “ (6.5 cm) between air discharge on

back of oven and back wall.

Oven Clearances

Installation

WARNING

Excessive Weight Hazard

Use two or more people to move and install oven.

Failure to do so can result in back or other injury.

7

TIME ENTRY pad is used to enter

cooking time for either manual entry

or programming. Cooking time ranges

from 1 second (00:01) to a total of 60

minutes (60:00) over four stages. If more

than 60 minutes of total microwave cooking time

is required, open door and inspect food before

beginning new cooking cycle.

Numbered pads begin cooking

programs or enter times and

power levels for “Manual Time .

Entry” cooking.

POWER LEVEL pad is used to set

microwave power level. When cooking, the

power level can be decreased for foods that require

slower more even cooking. Microwave power levels

range from 0% to 100% in 10% increments. If

cooking time is set and START pad pressed, oven

cooks at 100% power. When programming, to reset

power level to 100%, press POWER LEVEL pad.

START pad begins Manual Time Entry

cooking or restarts an interrupted cooking

cycle. When programming, use to save time

and power level, and to advance to next

user option.

STOP/ RESET pad exits programming

mode and stop cooking during cooking

cycle.

Display (some models)

Some items in display can

be seen but will not glow.

Stages

This oven can be programmed to run 4 cooking

sequences consecutively. Each sequence is called

a stage. For example, the rst cycle could be

programmed to defrost at 60% power, the second

to defrost at 30% power, the third to heat at 100%

power, and the fourth to hold warm at 10% power.

Total time for all cooking stages counts down.

User Options

User Options allow the user to program the oven

to perform in a way convenient to the user. The

beeps, maximum cooking time, and number of pre-

programmed cooking sequences can be changed.

X2 Pad

The X2 Pad increases a preset cooking time

by a percentage of

the original cooking time. The user species the

percentage and it can be changed for individual

cooking sequences. This feature is very useful

for cooking multiple servings of foods such as

potatoes or slices of pizza.

Display and Features

NOTE: There are two styles of controls shown Style 1 and Style 2 choose the control that

matches unit

STYLE 1

Time Entry

Quantity

Power Level

Start

Stop / Reset

8

MANUAL TIME ENTRY

Manual Time Entry feature allows the operator

to heat without changing the preprogrammed

pads. Time must be entered and power can be

set before cooking. START pad must be pressed

to begin cooking.

Programming Displays

This display indicates

oven is in programming

mode and ready to

program a numbered

pad(s).

This display indicates

oven is set to double pad

entry and 2 pads must be

pressed to enter a program.

See “Programming” section of manual for programming

procedure or “User Options” to change from single or

double pad entry.

This display shows briey

when programming more

than one stage. It indicates

programming mode for

pad 02. Press Time Entry

to choose stage to be programmed.

This display indicates

programming user

options mode. See

“User Options”

section of manual for

programming procedure.

PI

--

P02

MEMORY PAdS

This oven can of store either 10 or 100 cooking

programs in memory.

Single Pad Cooking

From the factory, it is programmed to store 10

cooking programs. Each pad begins a cooking

program.

Double Pad Cooking

The oven control can be changed to

store up to 100 cooking programs. To

set the control to 100 cooking programs,

see the “User’s Options” section of

this manual. To heat when the oven

is set for 100 programs , press 2 memory pads. For

example, to start the rst program, press pad 0, then

pad 1. To use the second program, press pad 0, then

pad 2. After the pads are pressed, the oven starts

automatically and time counts down.

Cooking Methods

Cooking Displays

READY shows when oven

control will accept entries.

14:37 shows

cooking time.

When more than

one cooking stage

is programmed,

total time for all stages

displays. COOKING Shows when microwave energy

is generated. % MW POWER shows when oven is

operating. 50 indicates the microwave power level

used. If number does not show, oven is cooking at

100% power.

STYLE 1

Display and Features

9

Double Pad Programs

The oven control can be changed to

store up to 100 cooking programs.

See the “User’s Options” section of this

manual to change oven control.

To start a double pad cooking program, press 2 memory

pads. For example, press pad 0 and pad 3 to start a

cooking program.

Manual Time Entry

Manual Time Entry feature allows the operator

to enter time and power levels, and heat without

changing the preprogrammed pads. Example: Heat for

30 seconds at 80% power.

1. Open oven door, place food in oven, and close door.

• Display shows “READY”. Fan and light operate.

• If pad is not pressed in 60 seconds, open and

close oven door again.

2. Press TIME ENTRY pad.

• Display shows “00:00” and “READY”.

3. Press 3 and 0 pad to enter cooking time.

4. Press POWER LEVEL

pad to change

power level.

• Display shows “% MW POWER” and current

power level if other than 100 percent power.

5. Press 8 pad to enter desired power level.

6. Press START pad.

• Oven operates and time counts down.

• Display shows cooking time, “COOKING”, “% MW

POWER”.

• Display shows “COOKING” only when microwave

energy is present.

• If power level other than 100 percent power was

programmed, display shows “COOKING” and “%

MW POWER”. Display counts down cooking time.

7. Oven stops cooking and oven signal sounds when

cooking timing elapses and display shows “DONE”.

Operation

Interrupting Operation

Open oven door or press STOP/RESET pad to

interrupt operation. Display continues to show

countdown time. Close door and press START pad

to resume oven operation.

Canceling Mistakes

If oven is not cooking, press STOP/RESET pad to

clear display. If oven is cooking, press STOP/RESET

pad once to stop oven, then again to clear display. If

oven door is open and time shows in display, close oven

door and press STOP/RESET pad to clear display.

Operating Preprogrammed Pads

From the factory, this oven can of store up to 10

preprogrammed cooking sequences in memory.

To heat using a preprogrammed sequence,

press a numbered pad. Oven starts to heat

automatically. Example: Heat using the third cooking

sequence.

1. Open oven door, place food in oven, and close oven

door.

• Display shows “READY”.

• If pad is not pressed in 60 seconds, open and

close oven door again.

2. Press 3 pad.

• Oven operates and time counts down.

• Display shows cooking time, “STAGE 1”,

”COOKING”. Display shows “COOKING” only

when microwave energy is present.

• If power level other than 100 percent power

was programmed, display shows “STAGE 1”,

“COOKING” and “% MW POWER”.

• If additional cooking time is required, press

preprogrammed pads before or after cooking cycle

ends.

3. Oven stops cooking and oven signal sounds when

cooking timing elapses.

Preprogrammed Times and Cook Level

All preprogrammed pads arrive set at full power.

STYLE 1

10

Memory Pads

From the factory, this oven can of store up to 10

cooking programs. Follow instructions below to program

cooking times and power levels for customized cooking.

Example: Program third cooking sequence to heat for 30

seconds at 80% power.

1. Open oven door.

• Display shows “DOOR”.

• If door is closed or STOP/RESET pad is

pressed before nishing programming sequence,

oven exits programming mode.

2. Press and hold pad 1 for approximately 5 seconds.

• After 5 seconds, signal sounds. Display shows

“PROGRAM”.

3. Press 3 pad to select memory pad.

• Display shows cooking time, “STAGE 1” and

power level if other than 100 percent power.

4. Press 3 and 0 pad to enter desired cooking time.

5. Press POWER LEVEL

pad to change

power level.

• Display shows cooking time and current power

level if other than 100 percent power.

6. Press 8 pad to enter desired power level.

Note: Press POWER LEVEL twice to reset to

100% power.

7. Press START

pad to save new cooking time

and power level in oven memory.

• Display shows “PROGRAM”.

• Repeat step 3–8 to program additional pads.

8. Press STOP/RESET pad or close oven door

to exit programming mode.

Double Pad Programs

The oven control can be changed to store up to 100

cooking programs. See the “User’s Options” section of

this manual to change oven control.

To create a double pad program, follow the instructions

above except for a change to step #3. When entering

the cooking program number, press 2 memory pads.

For example, press pads 0 and pad 3 to create a new

cooking program.

Multiple Cooking Stages

Follow instructions below to program oven to perform

four consecutive cooking cycles without interruption.

Example: Program third cooking sequence to heat for 30

seconds at 80% power, 40 seconds at 50% power, and

10 seconds at 100% power.

1. Open oven door.

• Display shows “READY”.

• If door is closed or STOP/RESET pad is

pressed before nishing programming sequence,

oven exits programming mode.

2. Press pad 1 for approximately 5 seconds.

• After 5 seconds, signal sounds. Display shows

“PROGRAM”.

3. Press 3 pad to select memory pad.

• Display shows “P03”briey then cooking time,

“STAGE 1” and power level if other than 100

percent power.

4. Press 3 and 0 to enter desired cooking time.

5. Press POWER LEVEL

pad to change

power level.

• Display shows “% MW POWER” and current

power level if other than 100 percent power.

6. Press 8 pad to enter desired power level.

7. Press TIME ENTRY

pad.

• Display shows cooking time, and “STAGE 2”

indicating programming stage 2 and power level

for stage shown in display.

• Repeat steps 5–8 to create additional stages.

8. Press START pad to save new cooking time

and power level in oven memory.

9. Press STOP/RESET pad or close oven door

to exit programming mode.

Programming

STYLE 1

11

User Options

Follow the instructions below to customized the

microwave oven’s operation. End-of-cycle signal,

maximum cooking time and other options can be

changed to meeting your cooking needs. Example:

Change setting to single digit pad operation.

1. Open oven door.

• If door is closed or STOP/ RESET pad is

pressed before nishing programming sequence,

oven exits programming mode.

2. Press and hold pad 2 for approximately 5 seconds.

• After 5 seconds, signal sounds. Display shows

“OPTIONS”.

3. Press 9 pad.

• See table for options.

• Displays shows “OP:90”.

• “OP” represents optional program mode, rst

number represents option number and second

number represents functions currently selected for

option.

4. Press 9 pad repeatedly to change setting.

5. Press START

pad to save changes.

• Repeat steps 3-5 to change additional options.

• Changes appear after door is closed or STOP/

RESET is pressed.

6. Press STOP/RESET pad or close oven door

to exit programming mode.

Numbered Pads Display Options ( Factory Settings in Bold)

1

End of Cycle Beep

OP:10

OP:11

OP:12

3 second continuous beep

Continuous beep until door is opened

5 beeps bursts until door is opened

2

Speaker Volume

OP:20

OP:21

OP:22

OP:23

Eliminates beep

Sets volume to low

Sets volume to medium

Sets volume to high

3

Key Beep

OP:30

OP:31

Prevents beep when pad is pressed.

Allows beep when pad is pressed.

4

Keyboard Enable

Window

OP:40

OP:41

OP:42

OP:43

15 seconds after oven door is opened, keyboard disabled

30 seconds after oven door is opened, keyboard disabled

1 minute after oven door is opened, keyboard disabled

2 minutes after oven door is opened, keyboard disabled

5

Add Time during

Heating

OP:50

OP:51

Prevents adding heating time while oven is heating.

Allows adding heating time while oven is heating when a

memory pad is pressed.

6

Reset Door Open

OP:60

OP:61

Cancels heating time count down after door is opened during

cycle.

Allows oven to resume heating time countdown after door is

opened during cycle.

7

Maximum Heating

Time

OP:70

OP:71

Allows 60 minutes of heating time.

Allows 10 minutes of heating time.

8

Manual Operation

OP:80

OP:81

Allows use of preprogrammed pads only.

Allows use of manual time entry and preprogrammed pads.

9

Double Digit

Operation

OP:90

OP:91

Allows 10 (0-9) preprogrammed pads.

Allows 100 (00-99) preprogrammed pads.

0

Clean Filter

Message

OP:00

OP:01

OP:02

OP:03

Do not display message.

Display message for 24 hours every 7 days.

Display message for 24 hours every 30 days.

Display message for 24 hours every 90 days.

STYLE 1

Options

12

Single Pad Programming

This feature enables each numbered pad to be programmed

for a specic use, such as cooking a certain number of

potatoes or defrosting and then cooking vegetables or other

frozen foods. To use this feature, simply program the pad to the desired

length of time and power level. To use this feature, press the pad once and

the microwave will begin cooking.

Double Pad Programming

This feature enables 100 programmed entries to be

made. Each entry will be assigned a double digit number,

for example 01, 05, or 20. When using the double pad programming, two

pads must be pressed to start the cooking cycle.

Manual Time Entry

In addition to programmable pads, this microwave also accepts

specic time entry by using the TIME ENTRY pad. Using manual time entry

does not affect the programmed buttons.

X2 Pad

The X2 Pad increases a preset cooking time by a percentage of

the original cooking time. The user species the percentage and it can be

changed for individual cooking sequences. This feature is very useful for

cooking multiple servings of foods such as potatoes or slices of pizza.

Stage Cooking

Stage cooking is a cooking sequence with specic power

stage changes. The user can program up to four different power level

changes and the specic amount of cooking time at each power level. Each

power level/cooking time combination is known as a stage. Up to four stages

can be programmed.

User Options

This microwave can be set for specic user preferences.

Options such as beep volume, maximum cooking time, and the number of

programmable pads can be changed. To change different options, see User

Options in this manual.

Start Pad

The start pad is used

to begin a manual time

entry cooking cycle. It is

also used to save any changes to

programming sequences or user

options.

STOP/RESET pad

The STOP/RESET pad

stops a cooking sequence

in progress, clears out any

remaining time, and also ends a

programming or user option cycle.

When the STOP/RESET pad is

used to end a programming or

option change, the changes are

discarded.

X

STYLE 2

Display and Features

13

Cooking Display

dISPLAYS dESCRIPTION

READY

READY displays when oven control will accept

entries.

00:00

Displays cooking time. If stage cooking is

programmed, total cooking time is displayed.

COOK LEVEL

COOK LEVEL displays while oven is operating.

The cooking level is displayed above as a number 1

through 9. If no number is displayed, the oven is

cooking at full power.

POWER

POWER is displayed while the oven is generating

microwave energy during a cooking cycle.

Programming Display

dISPLAYS dESCRIPTION

P:0

Displays when oven is in programming mode for

single pad memory only.

P:

Displays when oven is in programming mode for

double pad memory.

OP: --

Displays when oven is in user option mode. User

options can then be set or specified.

CF:

Displays with a numerical cooking factor when the

X2 pad is pressed.

P:--

1

Displays briefly when programming a specific

cooking stage. Number (1 through 4) indicates

the stage that is being programmed.

There are words in

the display that never

actually display.

The display is used for

many dierent models of

microwaves. Depending on the model,

certain words or symbols may never be

highlighted or become visible.

Oven Display

Oven Control

Pads

Self-sealing Base

Door Handle

(Pull to open)

Oven Door Window

(Some Models)

Removeable

Splatter Shield

(Not Shown)

Rear Air Vents

(some models)

5' 6" Power Cord

Oven Cavity Light

(Some Models)

Stainless Steal

Outer Case

STYLE 2

Operation

14

Preprogrammed Pads

To cook food using pads preprogrammed with cooking

sequences.

1. Open oven door and place food in oven. Close door.

• READY displays. Fan and light will turn on.

2. Press desired pad.

• For single pad entry, press only one pad.

• For double pad entry, press the two pads, in order,

of the double digit number for the desired cooking

sequence.

• To change single or double pad entry option see

User Options section in this manual.

3. Oven begins to cook.

• POWER, COOK LEVEL and total cooking time display.

• For additional cooking time, press preprogrammed pad again

to begin cooking sequence again.

X2 Pad

To increase cooking time

when cooking more than one serving.

1. Open oven door and place food

in oven. Close door.

• READY displays. Fan and

light will turn on.

2. Press X2 pad.

• Amount of time added is a

percentage of the original

preprogrammed cooking time.

• The percentage can be

changed. See Programming

section in this manual.

3. Press desired preprogrammed pad.

4. Oven begins cooking. Displayed

cooking time is the total of original

cooking time and added X2 time.

Interrupting

Operation

Open oven door or press

STOP/RESET pad to

interrupt operation. Display

continues to show countdown time.

Close door and press START pad

to resume oven operation.

Canceling Mistakes

• If oven is not cooking, press

STOP/RESET pad to clear display.

• If oven is cooking, press

STOP/RESET pad once to stop

oven, then again to clear display.

• If oven door is open and time

shows in display, close oven

door and press STOP/RESET

pad to clear display.

Factory Settings

Manual Time Entry

To cook food using a specic entered time and power level.

1. Open oven door and place food in oven. Close door.

• READY displays. Fan and light will turn on.

2. Press TIME ENTRY pad.

• READY and 00:00 display.

• If pad does not work, open and close oven door and try

again.

3. Enter cooking time by using the numbered pads.

4. Press POWER LEVEL pad to change power level.

• COOK LEVEL displays with the power setting.

• If a number is not displayed with COOK LEVEL the

microwave is set to full power.

• Press a number pad to adjust power level to desired setting.

5. Press TIME ENTRY pad.

• Display changes to cook time and power level for the next stage.

6. Enter cook time and power level as in steps 3 and 4.

• To add another cooking stage press TIME ENTRY pad again.

• Up to four different stages can be programmed.

7. Press START pad.

• Oven operates and time counts down.

• POWER, COOK LEVEL and cooking time display.

STYLE 2

Operation

15

Programming Pads

Oven is shipped from the factory for single pad programming. To change

the oven default to allow double pad programming, see User Options.

To change the amount of time or the power level for a preset pad:

1. Open oven door.

• READY displays.

• If door is closed or RESET pad is pressed before programming

is complete, changes are discarded and microwave exits

programming mode.

2. Press and hold pad 1 for approximately 5 seconds.

• This begins programming mode.

• Microwave will beep and P:0 displays. Oven is in

programming mode.

3. Press pad to be reprogrammed.

• Press two digits if reprogramming a double pad program.

• COOK LEVEL and cooking time display.

• A number displays with COOK LEVEL if it is less than full power.

4. Enter cooking time by using the number pads.

5. Press POWER LEVEL pad to change power level if desired.

• Use the number pads to change power level to a lower

power setting.

6. Press START pad to set new programming to the pad.

• If START is not pressed, changes will not be saved.

• P:0 displays

7. Press STOP/RESET pad or close oven door to exit

programming mode.

Programming Multiple Stages

Stage cooking allows consecutive cooking cycles without interruption.

Up to four different cooking cycles can be programmed into a memory

pad. To use stage cooking:

1. Follow steps 1 through 5 above.

6. Press TIME ENTRY pad.

• Display briey shows the pad number that is being

programmed and the stage number to the upper right.

• Display changes to cook time and power level for the next stage.

7. Enter cook time and power level as in steps 4 and 5.

• To enter another cooking stage for that pad, press TIME ENTRY

pad again.

• Up to four different stages can be programmed.

8. Press START pad to set new programming changes to the pad.

X2 Programming

This feature allows a preset

percentage of original cook

time, called a cooking factor, to be

added to a cook sequence.

To change the cooking factor:

1. Open oven door.

2. Press and hold pad 1 for

approximately 5 seconds.

3. Press pad to be reprogrammed.

4. Press the X2 pad.

5. Press a numbered pad to

change the cooking factor.

• Pad 5 would change the

cooking factor to 50%.

• Pad 3 would change the

cooking factor to 30%.

6. Press START pad to save changes.

Programming

STYLE 2

16

Changing user options

Options such as single or double pad programming, beep volume, and

maximum cooking time can be changed to suit individual preferences.

To change options:

1. Open oven door.

• If door is closed or RESET pad is pressed before programming is

complete, changes are discarded and microwave exits programming

mode.

2. Press and hold pad 2 for approximately 5 seconds.

• This begins options mode.

• Microwave will beep and 0P: displays. Microwave is now in

programming mode.

3. Press number pad that controls option to be changed.

• See table below for options.

• Current option will display.

4. Press number pad again to change the option.

• Each time pad is pressed, option will change.

• Match code displayed with code for desired option.

5. Press START pad to save changes.

• To change additional options, repeat steps 3 and 4.

• Changes appear after door is closed or STOP/RESET pad is pressed.

Numbered Pads Display Options ( Factory Settings in Bold)

1

End of Cycle Beep

OP:10

OP:11

OP:12

3 second continuous beep

Continuous beep until door is opened

5 beeps bursts until door is opened

2

Speaker Volume

OP:20

OP:21

OP:22

OP:23

Eliminates beep

Sets volume to low

Sets volume to medium

Sets volume to high

3

Key Beep

OP:30

OP:31

Prevents beep when pad is pressed.

Allows beep when pad is pressed.

4

Keyboard Enable

Window

OP:40

OP:41

OP:42

OP:43

15 seconds after oven door is opened, keyboard disabled

30 seconds after oven door is opened, keyboard disabled

1 minute after oven door is opened, keyboard disabled

2 minutes after oven door is opened, keyboard disabled

5

Add Time during

Heating

OP:50

OP:51

Prevents adding heating time while oven is heating.

Allows adding heating time while oven is heating when a

memory pad is pressed.

6

Reset Door Open

OP:60

OP:61

Cancels heating time count down after door is opened during

cycle.

Allows oven to resume heating time countdown after door is

opened during cycle.

7

Maximum Heating

Time

OP:70

OP:71

Allows 60 minutes of heating time.

Allows 10 minutes of heating time.

8

Manual Operation

OP:80

OP:81

Allows use of preprogrammed pads only.

Allows use of manual time entry and preprogrammed pads.

9

Double Digit

Operation

OP:90

OP:91

Allows 10 (0-9) preprogrammed pads.

Allows 100 (00-99) preprogrammed pads.

0

Clean Filter

Message

OP:00

OP:01

OP:02

OP:03

Do not display message.

Display message for 24 hours every 7 days.

Display message for 24 hours every 30 days.

Display message for 24 hours every 90 days.

Didn’t like an option?

Factory settings are marked in bold. To

change the oven back to the factory

setting, simply select the option that is

marked in bold.

My changes weren’t

saved.

In order for any changes to be

saved, the START pad must

be pressed after selecting

an option. Shutting the oven door or

pressing the STOP/RESET pad will not

Options

STYLE 2

17

Care and Cleaning

Part Description

Interior, Exterior, and Door

Clean microwave oven with mild detergent in warm water using soft

sponge or cloth. Wring sponge or cloth to remove excess water before

wiping equipment. If desired, boil a cup of water in microwave oven to

loosen soil before cleaning.

Important:

• Do not use abrasive cleansers or cleaners containing ammonia.

These could damage finish.

• Never pour water into microwave oven bottom.

• Do not use water pressure type cleaning systems.

Discharge Air Vents

Check monthly for a buildup of cooking vapors along intake and discharge

louvers on bottom and back of oven. Clean air vents with damp cloth to

ensure proper airflow. Dry thoroughly.

Control Panel

Open oven door to deactivate oven timer. Clean with mild detergent in

warm water using soft sponge or cloth.

Discharge Air Vents

CAUTION

!

To avoid electrical shock which can cause personal injury, unplug power cord or open circuit breaker to oven

before cleaning or removing light bulb.

18

noitpircseDtraP

reporp rof ylkeew retlif ekatni ria naelC .rood nevo woleb detacol si retliFretliF ekatnI riA

airow. Wash lter in hot water and mild detergent. Do not use oven

without lter in place. Remove lter to clean.

Important

To avoid overheating and oven damage, clean air lter regularly.

1. Grasp lter tab and pull forward. Filter will release from retaining clips.

2. To reinstall, place bottom of lter in clips and push top of lter into

position.

morf annetna dna ytivac nevo evaworcim fo pot speek dleihs rettalpSsdleihS rettalpS

becoming soiled. Clean soil from shield with damp cloth or clean with mild

detergent and water. Remove splatter shield for easy cleaning.

Removing Splatter Shield

1. Unplug oven before removing splatter shield to stop antenna from

rotating.

2. Place ngers behind shield, pull forward, and down.

• When removing and replacing splatter shield, be careful not to bend

antenna.

• If a gap for ngers behi

nd spla

tter shield does not exist, push up on

splatter shield front. Splatter shield may not be installed fully and

cannot be removed until splatter shield front is properly installed.

3. Reinstall splatter shield by placing front tabs over lip at top of oven

cavity front. Lift back of shield until shield snaps into place.

4. Reconnect power to oven.

Changing Oven Light Bulb

Important

To avoid burns and cuts, wear gloves to protect hands should bulb

break. If hot, allow bulb to cool.

Tools and Bulb

• Protective gloves

• Standard screwdriver or ¼-inch socket

1. Unplug oven.

2. Remove screw from side of oven.

3. Remove bulb by turning counterclockwise, being careful not to burn

ngers or break bulb.

4. Reconnect power to oven.

Shield

up side down

Shield in

correctly

19

Before Calling for Service

Record all inspections and repair for future reference.

!

WARNING

To avoid electrical shock which can cause severe personal injury or death, do not remove outer case at any time.

Only an authorized servicer should remove outer case.

kcehCmotpmyS

I

f oven does not operate:

• Check fuse or circuit breaker.

• Conrm oven is plugged into dedicated circuit.

• Conrm oven is on grounded and polarized circuit.

Contact electrician to conrm.

If oven light does not work:

• Conrm light bulb is screwed in tightly.

• Conrm light bulb has not failed.

If oven does not accept entries when pad is pressed:

• Open and close oven door. Press pad again.

.nevo ni gulp dna ,etunim 1 rof tiaw ,nevo gulpnU•:snoitcnuflam nevo fI

Check air intake and discharge area for obstrutions.•:yltnettimretni setarepo nevo fI

Oven operates, but does not heat food: • Place one cup cool water in oven. Heat for one

minute. If water temperature does not rise, oven is

operating incorrectly and a service should be

called.

www.acpsolutions.com



2012 ACP Inc.

Cedar Rapids, Iowa 52404

Part No. 20072201

Printed in U.S.A. 05/12

Manual del usuario

Horno de microondas compacto

comercial para uso rudo

[0.6 pies cúbicos]

Conserve estas instrucciones como referencia futura.

Si el horno cambia de propietario, este manual

debe acompañar al horno.

Contenido

Identicación del modelo ..........................2

InstruccIones de segurIdad

Importantes ..............................3

precaucIones para evItar una

posIble exposIcIón a un exceso

de energía de mIcroondas ......... 4

Instrucciones para el aterrizado

o conexión a tierra .................................5

Instalación .................................................6

Pantalla y características Estilo 1 .............7

Operación Estilo 1.....................................9

Programación Estilo 1 .............................10

Opciones Estilo 1 ....................................11

Pantalla y características Estilo 2 ...........12

Operación Estilo 2...................................13

Programación Estilo 2 .............................15

Opciones Estilo 2 ....................................16

Cuidado y limpieza..................................17

Antes de llamar al servicio ......................19

La page charge ...

Amana UPRIGHT FREEZER Le manuel du propriétaire

Amana UPRIGHT FREEZER Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents