NAPOLEON WPV080T3AA-N Manuel utilisateur

IOM

W415-2308 / C / 09.22.20

UM

PG

69

$10.00

INSTALLER: PLEASE FAMILIARIZE YOURSELF WITH VENTING/DRAINING SECTIONS OF

THIS MANUAL BEFORE PROCEEDING WITH THE INSTALLATION. LEAVE

THIS MANUAL WITH THE APPLIANCE FOR FUTURE REFERENCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)722-6031 • www.napoleon.com • [email protected]

SAFETY INFORMATION

ELECTRICAL SHOCK, FIRE OR EXPLOSION

HAZARD

Failure to follow safety warnings exactly could result in

serious injury, death or property damage.

Improper servicing could result in dangerous operation,

serious injury, death or property damage.

As a professional installer, you have an obligation to know the product

better than the customer. This includes all safety precautions and related

items.

Prior to actual installation, thoroughly familiarize yourself with this

instruction manual. Pay special attention to all safety warnings. Often

during installation or repair, it is possible to place yourself in a position

which is more hazardous than when the unit is in operation.

Remember, it is your responsibility to install the product safely and to

know it well enough to be able to instruct a customer in its safe use.

!

WARNING

!

MANUFACTURER RESERVES THE RIGHT TO DISCON-

TINUE, OR CHANGE AT ANY TIME, SPECIFICATIONS

OR DESIGNS WITHOUT NOTICE AND WITHOUT INCUR-

RING OBLIGATIONS.

H1.52A

CERTIFIED TO ANSI Z21.47-2016 / CSA 2.3-2016

WPV-N SERIES

TWO STAGE MULTI POSITION HIGH EFFICIENCY (CONDENSING) FORCED AIR

GAS FURNACE

UPFLOW

HORIZONTAL

RIGHT

DOWNFLOW

HORIZONTAL

LEFT

Patent pending

W415-2308 / C / 09.22.20

2

IOM

TABLE OF CONTENTS

1.0 INTRODUCTION 4

2.0 SAFETY SYMBOLS AND WARNINGS 4

2.1 SAFETY RULES 6

2.2 CODES 7

3.0 FURNACE SIZING 9

3.1 MODEL INPUT AND TEMPERATURE RISE 9

4.0 LOCATION OF UNIT 10

4.1 GENERAL GUIDELINES 10

4.2 OTHER CONSIDERATIONS 10

4.3 INSTALLATION IN UPFLOW, DOWNFLOW OR HORIZONTAL POSITIONS 11

4.4 AIR CONDITIONING 12

5.0 COMBUSTIBLE CLEARANCES 12

6.0 DUCTWORK 13

6.1 DUCTWORK STEPS 14

7.0 VENTING AND COMBUSTION PIPING 15

7.1 ACCEPTABLE MATERIALS IN CANADA 15

7.2 ACCEPTABLE MATERIALS IN UNITED STATES 15

7.3 VENT DRAIN OPTION 16

8.0 NON-DIRECT VENT FURNACE INSTALLATIONS USING INDOOR COMBUSTION AIR (ONE PIPE

SYSTEM) 17

8.1 DETERMINING COMBUSTION AIR 17

8.1.1 CASE 1: FURNACE LOCATED IN A UNCONFINED SPACE 17

8.1.2 CASE 2: FURNACE LOCATED IN A CONFINED SPACE 18

8.1.3 CASE 3: FURNACE LOCATED IN A CONFINED SPACE, OUTDOOR AIR FROM ATTIC OR

CRAWL SPACE 18

8.1.4 CASE 4: FURNACE LOCATED IN A CONFINED SPACE, OUTDOOR AIR DUCTED

HORIZONTALLY 19

8.1.5 CONNECTION TO FURNACE NON-DIRECT VENT 20

9.0 VENTING GUIDELINES 21

9.1 VENT TERMINATION 22

9.2 IN CANADA 23

9.3 IN UNITED STATES 23

9.4 FURNACE VENTING INSTALLATIONS 24

9.4.1 NON-DIRECT VENT INSTALLATION USING INDOOR COMBUSTION AIR (ONE PIPE

SYSTEM) 24

9.4.2 DIRECT VENT INSTALLATION USING OUTDOOR COMBUSTION AIR (TWO PIPE SYSTEM)

24

9.4.3 COMBUSTION AIR 24

10.0 TERMINATIONS 25

10.1 COMBUSTION AIR 25

10.2 EXHAUST 25

10.3 CONCENTRIC VENTING KIT 25

10.4 CONCENTRIC VENT TERMINATION INSTALLATION INSTRUCTIONS 25

10.5 LOCATION 25

10.6 MULTIPLE VENTING 26

11.0 ROUTING OPTIONS 29

11.1 CONDENSATE DRAINS 29

11.2 PREPARATIONS FOR VENT AND DRAINING OPTION 29

11.3 EXHAUSTER ROTATION INSTRUCTIONS & PRESSURE SWITCH MOUNTING 31

11.4 DRAIN HOSE INSTALLATION 38

11.4.1 DRAIN PIPING 38

11.4.2 PRIMING CONDENSATE TRAP 39

11.5 ALTERNATE CONDENSATE DRAIN PIPING INSTALLATION USING PVC OR CPVC 40

11.6 CONDENSATE NEUTRALIZERS 40

12.0 GAS SUPPLY AND PIPING 41

12.1 GAS SUPPLY 41

12.2 GAS PIPING 41

W415-2308 / C / 09.22.20

3

IOM

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

12.3 GAS INLET PRESSURE 42

12.4 LEAK TESTING 42

12.5 PURGING GAS LINES 42

13.0 CONVERSIONS 43

13.1 HIGH ALTITUDE CONVERSION 43

13.2 NATURAL TO LP GAS 43

13.3 CONVERSION STEPS 43

13.4 CHECKING THE INLET GAS PRESSURE 43

13.5 SETTING THE MANIFOLD GAS PRESSURE 44

13.6 CHECKING FURNACE INPUT 45

14.0 ELECTRICAL SPECIFICATIONS 46

14.1 ELECTRICAL WIRING AND CONNECTIONS 46

14.2 FURNACE CONNECTION 47

15.0 LOW VOLTAGE WIRING 47

15.1 SINGLE STAGE THERMOSTAT 47

15.2 TWO STAGE THERMOSTAT 48

15.3 THERMOSTAT LOCATION 48

15.4 FURNACE PAIRED WITH HEAT PUMP 49

16.0 OPTIONAL ACCESSORIES (FIELD SUPPLIED/INSTALLED) 49

16.1 ELECTRONIC AIR CLEANER 49

16.2 POWER HUMIDIFIER 49

17.0 STARTUP PROCEDURES 49

17.1 TO START THE FURNACE 50

17.2 TO SHUT DOWN THE FURNACE 50

17.3 SEQUENCE OF OPERATION 51

18.0 AIR FLOW 52

18.1 TEMPERATURE RISE CHECK 52

18.2 CALCULATING AIR FLOW 52

18.3 BLOWER AIRFLOW 53

18.4 DEHUMIDIFICATION 54

18.5 BLOWER “ON” AND “OFF” TIMINGS 55

18.6 CONTINUOUS FAN OPERATION 55

19.0 MAINTENANCE AND TROUBLESHOOTING 56

19.1 AIR FILTER 56

19.2 LUBRICATION 56

19.3 CLEANING 57

19.4 TROUBLESHOOTING FLOWCHART 60

19.5 DIAGNOSTIC CODES FOR STATUS LED 61

19.6 FAULT CODE HISTORY 61

20.0 WIRE DIAGRAM FOR TWO STAGE FURNACE 62

21.0 WARRANTY 64

22.0 REPLACEMENT PARTS LIST 65

23.0 SERVICE HISTORY 67

24.0 NOTES 68

H1.22

IMPORTANT:

PLEASE READ THIS MANUAL CAREFULLY

AND KEEP IN A SAFE PLACE FOR FUTURE

REFERENCE BY A SERVICE TECHNICIAN.

This manual is for the:

WPV-N Series (WPV040T2AA-N / WPV060T3AA-N / WPV080T3AA-N / WPV080T4BA-N

/ WPV100T5BA-N / WPV120T5BA-N)

These models may be referenced according to their input (K/Btu/hr) in some ﬁ gures (i.e. 40

/ 60 / 80-3 / 80-4 / 100 / 120).

W415-2308 / C / 09.22.20

4

IOM

H6.0

IMPORTANT:

READ THE FOLLOWING INSTRUCTIONS COMPLETELY BEFORE INSTALLING!

H3.3.1

Understand and pay particular attention to the words DANGER, WARNING, and CAUTION and the following

deﬁ ned symbols are used throughout this manual to notify the reader of potential hazards of varying risk levels.

DANGER

! !

INDICATES AN IMMINENTLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, WILL

RESULT IN DEATH OR SERIOUS INJURY.

INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED,

COULD RESULT IN DEATH OR SERIOUS INJURY.

WARNING

!

INDICATES A POTENTIAL HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, MAY

RESULT IN MINOR OR MODERATE INJURY. IT MAY ALSO BE USED TO ALERT

AGAINST UNSAFE PRACTICES.

CAUTION

!

This high efﬁ cient gas ﬁ red two stage condensing furnace is an upﬂ ow, downﬂ ow, horizontal left and right

warm air furnace suitable for residential and light commercial heating applications with inputs of 40,000, to

120,000Btu/hr.

This high efﬁ cient furnace series is CSA certiﬁ ed as a Category IV indirect or direct vent central forced air fur-

nace. When installed as a direct vent furnace, all combustion air is supplied to the furnace burners through the

air intake system. (See Section 7, “Ventilation and Combustion Piping.”)

All models may be ﬁ red by natural or LP gas (propane), and may be ﬁ eld converted from natural gas to LP gas

using Conversion Kit W370-0018.

The furnace is shipped completely assembled except for the condensate drain trap assembly and the furnace

upper door. Please inspect for damage when the furnace is unpacked.

1.0 INTRODUCTION

2.0 SAFETY SYMBOLS AND WARNINGS

W415-2308 / C / 09.22.20

5

IOM

H3.3A

WARNING

!

IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE

OR EXPLOSION MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR

LOSS OF LIFE.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS, OR

OTHER COMBUSTIBLE MATERIALS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

WHAT TO DO IF YOU SMELL GAS

• DO NOT TRY TO LIGHT ANY APPLIANCE.

• DO NOT TOUCH ANY ELECTRICAL SWITCH; DO NOT USE ANY PHONE IN YOUR

BUILDING.

• IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A NEIGHBOR’S PHONE, OR A CEL-

LULAR PHONE FROM A LOCATION WELL AWAY FROM THE BUILDING. FOLLOW THE

GAS SUPPLIER’S INSTRUCTIONS.

• IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALL THE FIRE DEPARTMENT.

• DO NOT RE-ENTER THE BUILDING UNTIL AUTHORIZED TO DO SO BY THE GAS

SUPPLIER OR THE FIRE DEPARTMENT.

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE

CAN CAUSE INJURY, PROPERTY DAMAGE OR LOSS OF LIFE. REFER TO THIS MANUAL.

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER,

SERVICE AGENCY OR THE GAS SUPPLIER.

H3.4

THESE INSTRUCTIONS ARE INTENDED AS AN AID TO QUALIFIED SERVICE

PERSONNEL FOR PROPER INSTALLATION, ADJUSTMENT AND OPERATION OF

THIS FURNACE. READ THESE INSTRUCTIONS THOROUGHLY BEFORE ATTEMPTING

INSTALLATION OR OPERATION. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY

RESULT IN IMPROPER INSTALLATION, ADJUSTMENT, SERVICE OR MAINTENANCE,

POSSIBLY RESULTING IN FIRE, ELECTRICAL SHOCK, CARBON MONOXIDE

POISONING, EXPLOSION, PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.

WARNING

!

H3.92

CARBON-MONOXIDE POISONING HAZARD

FAILURE TO FOLLOW INSTRUCTIONS COULD RESULT IN SEVERE PERSONAL INJURY

OR DEATH DUE TO CARBON-MONOXIDE POISONING, IF COMBUSTION PRODUCTS

INFILTRATE INTO THE BUILDING.

CHECK THAT ALL OPENINGS IN THE OUTSIDE WALL AROUND THE VENT (AND

AIR INTAKE) PIPE(S) ARE SEALED TO PREVENT INFILTRATION OF COMBUSTION

PRODUCTS INTO THE BUILDING.

CHECK THAT FURNACE VENT (AND AIR INTAKE) TERMINAL(S) ARE NOT

OBSTRUCTED IN ANY WAY DURING ALL SEASONS.

WARNING

!

W415-2308 / C / 09.22.20

6

IOM

2.1 SAFETY RULES

H6.7A

1. Use this furnace only with type of gas approved for this furnace. Refer to the furnace rating plate.

2. Install this furnace only in dry indoor locations (protected from weather).

3. Provide adequate combustion and ventilation air to the furnace space as speciﬁ ed in Section 7 of this

manual, “Ventilation and Combustion Piping.”

4. Combustion products must be discharged outdoors. Connect this furnace to an approved vent system only,

as speciﬁ ed in Section 7 of this manual, “Venting and Combustion Piping.”

5. Never test for gas leaks with an open ﬂ ame. Use a commercially available soap solution made speciﬁ cally

for the detection of leaks to check all connections as speciﬁ ed in Section 12 of this manual, “Gas Supply

and Piping.”

6. Always install furnace to operate within the furnace’s intended temperature-rise range with a duct system,

which has an external static pressure within the allowable range, listed on the furnace rating plate, and as

speciﬁ ed in Sections 3, 6, and 18 of this manual, “Furnace Sizing,” “Ductwork,” and “Airﬂ ow.”

7. When a furnace is installed so that the supply ducts carry air circulated by the furnace to areas outside the

space containing the furnace, the return air shall also be handled by duct(s) sealed to the furnace casing and

terminating outside the space containing the furnace. (Furnace for heating the home located in the attached

garage, for example).

8. A gas-ﬁ red furnace for installation in a residential garage must be installed so that the burners and ignitor

are no less than 18” (457 mm) above the ﬂ oor. The furnace must be located, or protected to avoid physical

damage by vehicles. (See safety warning).

9. Wolf Steel furnaces may be used as a construction heater provided that the furnace installation and

operation of the appliance complies with the items listed below:

a) The vent system must be permanently installed per manufacturer’s instructions. One hundred percent

(100%) outdoor air must be provided for combustion air requirements during construction. This is to

minimize the corrosive effects of adhesives, sealers and other construction materials. It also prevents

the entrainment of drywall dust into combustion air, which can cause fouling and plugging of furnace

components.

b) Furnace must be operating under thermostatic control. The use of ﬁ xed jumpers that will provide

continuous heating is not allowed.

c) Air ﬁ lters must be installed in the system and replaced or maintained daily during construction.

d) The return air duct must be provided and sealed to the furnace.

e) Return air temperature range between 55°F (13°C) and 80°F (27°C) must be maintained with no

evening setback or shutdown.

f) The input rate and temperature rise must be set per the furnace rating plate.

g) The furnace, ductwork and ﬁ lters are cleaned as necessary to remove drywall dust and

construction debris from all HVAC system components and verify furnace operating conditions including

ignition, input rate, temperature rise, and venting, according to the manufacturer’s instructions after

construction is completed.

h) Furnace doors must be in place on the furnace while the furnace is operating in any mode. Damage or

repairs due to failure to comply with these requirements are not covered under the warranty.

W415-2308 / C / 09.22.20

7

IOM

2.2 CODES

H6.2

1. This furnace must be installed:

a. In accordance with all local codes, by-laws and regulations by those authorities having jurisdiction.

b. In Canada, this furnace must be installed in accordance with the current CAN/CGA -B149.1 and .2

Natural Gas and Propane, and the National Electric Code (NEC) NFPA 70.

c. In the United States, this furnace must be installed in accordance with the current ANSI Z223.1 (NFPA

54) National Fuel Gas Code.

2. Electrical connections must be made in accordance with:

a. Any applicable local codes, by-laws and regulations.

b. Canada: current edition of CAN/CSA C22.1 and C22.2, Canadian Electrical Code (Part 1 and 2).

c. United States: current edition of ANSI/NFPA 70, National Electrical Code.

Codes and additional information may be obtained from:

Canadian Standards Association American Gas Association

5060 Spectrum Way 400 North Capitol Street, NW, Suite 450

Mississauga, Ontario, L4W 5N6 Washington DC, 20001

Phone: (416) 747-4000 Phone: (202) 824-7000

website: www.csa.ca website: www.aga.org

National Fire Protection Association

1 Batterymarch Park

Quincy, MA, 02169-7471

Phone: (617) 770-3000

website: www.nfpa.org

H3.5

DO NOT INSTALL THIS FURNACE IN A MOBILE HOME! THIS FURNACE IS NOT

APPROVED FOR INSTALLATION IN A MOBILE HOME. DOING SO COULD CAUSE FIRE,

PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

THE FURNACE CONTAINS FOIL COVERED FIBERGLASS INSULATION. INHALATION OF

FIBERGLASS PARTICLES IS ASSOCIATED WITH RESPIRATORY DISEASE INCLUDING

CANCER.

NATURAL GAS AND PROPANE ARE NORMALLY ODORIZED BY THE FUEL SUPPLIER. IN

SOME CASES, THE ODORANT MAY NOT BE PERCEIVABLE. INSTALLATION OF UL AND

ULC RECOGNIZED FUEL GAS DETECTORS INSTALLED IN ACCORDANCE WITH THEIR

MANUFACTURER’S INSTRUCTIONS IS RECOMMENDED AS AN ADDITIONAL MARGIN OF

SAFETY.

THE EXHAUST GASES FROM THIS FURNACE CONTAIN CHEMICALS WHICH ON

SOME OCCASIONS MAY INCLUDE CARBON MONOXIDE. CARBON MONOXIDE IS AN

ODORLESS, TASTELESS, CLEAR COLORLESS GAS WHICH IS HIGHLY TOXIC. EVEN

LOW CONCENTRATIONS ARE SUSPECTED OF CAUSING BIRTH DEFECTS AND OTHER

REPRODUCTIVE HARM.

UL AND ULC RECOGNIZED CO DETECTORS ARE RECOMMENDED FOR ALL BUILDINGS

EQUIPPED WITH FOSSIL FUEL BURNING APPLIANCES. ALL CO DETECTORS SHOULD

BE INSTALLED IN ACCORDANCE WITH THEIR MANUFACTURER’S INSTRUCTIONS AND

APPLICABLE LOCAL BUILDING CODES.

FIRE, EXPLOSION OR CARBON MONOXIDE POISONING HAZARD!

FAILURE TO REPLACE WITH PROPER CONTROL COULD RESULT IN FIRE, EXPLOSION

OR CARBON MONOXIDE POISONING.

REPLACE GAS VALVE ONLY WITH THE SAME MODEL NUMBER OR AS SPECIFIED BY THE

MANUFACTURER.

WARNING

!

W415-2308 / C / 09.22.20

8

IOM

FIGURE 1 - FURNACE DIMENSIONS

0"

Top

NOTES:

S - Service clearance 24 inches (610mm) or more.

C - Combustible oor (but not carpet or non-ceramic tile).

All models approved for closet installation.

Plenum

1/2" (13mm)

on all sides

0"

H12.11.2

UPFLOW DOWNFLOW HORIZONTAL

TOP 0 0 0

PLENUM TOP 1/2" (13mm) 0 1/2" (13mm)

FRONT 0* 0* 0*

BACK 0 0 0

SIDES 0 0 0**

BOTTOM 0*** 0 0

FLUE PIPE 0 0 0

ENCLOSURE CLOSET CLOSET CLOSET

*24" (610mm) REQUIRED FOR SERVICE

**SUPPLY AIR OUTLET / 1/2" (13mm) RETURN AIR INLET

*** CERTIFIED FOR CLOSET INSTALATION ON COMBUSTIBLE FLOORING.

H3.6A

WARNING

!

WHEN THIS FURNACE IS INSTALLED IN A STORAGE GARAGE, IT MUST BE INSTALLED

SO THE BURNERS AND IGNITION SOURCE ARE LOCATED NO LESS THAN 18” (457 mm)

ABOVE THE FLOOR TO PREVENT THE RISK OF IGNITING FLAMMABLE VAPORS WHICH

MAY BE PRESENT IN THE GARAGE.

THE FURNACE MUST BE LOCATED OR PROTECTED TO AVOID PHYSICAL DAMAGE BY

VEHICLES.

FAILURE TO HEED THESE WARNINGS CAN CAUSE A FIRE OR EXPLOSION, RESULTING

IN PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

TABLE B - MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS

TABLE A - FURNACE DIMENSIONS

INPUT Width Depth Height Supply Air Return Air

K/Btu/hr A B C (F x G) (D x E)

40

17 1/2"

(445mm)

29 1/2"

(749mm)

34”

(864mm)

16 1/4" x 19 5/8"

(413mm x 499mm)

14" x 23"

(356mm x 584mm)

60

80-3

80-4

22 1/2”

(572mm)

21 1/4” x 19 5/8”

(540mm x 499mm)

100*

120*

H12.6.12C

TABLE B - MINI

MU

M

CL

EARA

NC

ES

T

O

CO

MB

US

TIBLE MATERIAL

S

*NOTE: If the airﬂ ow requirements exceed 1800 cfm, models will require air openings and

ﬁ lters on: • both sides, OR

• one side and the bottom, OR

• just the bottom

W415-2308 / C / 09.22.20

9

IOM

FIRE

RATE

INPUT OUTPUT

DELTA

T (°F)

WPV040T2AA-N

High Fire 40,000 38,000 40-70

Low Fire 24,000 23,000 35-65

WPV060T3AA-N

High Fire 60,000 58,000 40-70

Low Fire 36,000 35,000 35-65

WPV080T3AA-N

High Fire 80,000 77,000 45-75

Low Fire 48,000 46,000 40-70

WPV080T4BA-N

High Fire 80,000 77,000 40-70

Low Fire 48,000 46,000 35-65

WPV100T5BA-N

High Fire 100,000 96,000 40-70

Low Fire 60,000 58,000 35-65

WPV120T5BA-N

High Fire 120,000 115,000 40-70

Low Fire 72,000 68,000 35-65

3.0 FURNACE SIZING

The maximum hourly heat loss for each heated space shall be calculated in accordance with the procedures

described in the manuals of the Heating, Refrigeration and Air Conditioning Institute of Canada (HRAI), or

by any other method which is suitable for local conditions, provided the results obtained are in substantial

agreement with, and not less than those obtained using the procedure described in their manuals.

In the United States, “Manual J - Load Calculation,” published by the Air Conditioning Contractors of America,

describes a suitable procedure for calculating the maximum hourly heat loss.

If the installation is a retroﬁ t application, do not rely on the capacity of the existing heating equipment as a

method to size the new furnace. Many of the heat transfer multiples listed in earlier versions of load calculation

manuals were much higher than those listed in more recent editions. It is possible that energy saving

measures have been completed since the installation of the existing furnace. This might include additional

insulation in the attic or walls, the application of sprayed foam insulation, the addition of storm windows and

doors, weather-stripping, caulking, etc.

Many of the older furnaces were equipped with large belt drive blower systems, operating at low RPM’s. If

replacing an existing furnace, be sure that the existing ductwork can handle the amount of airﬂ ow necessary

for a reasonable temperature rise. Most older gas furnaces operated with a system temperature rise of 70 -

100°F (39 - 56°C). This furnace is designed to be operated with a system temperature rise (∆T) as illustrated

in “model input and temperature” section. If the furnace selected has an identical output capacity as the

original furnace, a substantial increase in system air ﬂ ow will be necessary. See section 3.1 and the airﬂ ow

characteristics in Section 18 of this manual.

Existing ductwork should be assessed for its air handling capabilities.

The “Equal Friction Chart,” as published by ASHRAE and HRAI, is the basis for the various air duct

calculators available through heating supply companies. Following the air velocity guide lines, according to

the “Equal Friction Chart,” or a slide rule air duct calculator, a typical 6" (152mm) round duct has a capacity of

approximately 100 cfm.

H7.0.7

NOTE:

The return air system is equally as important as the supply air system. An under-sized return air system

will prevent sufﬁ cient quantities of air from reaching the supply air system and will consequently reduce

the service life of the furnace and its components.

3.1 MODEL INPUT AND TEMPERATURE RISE

W415-2308 / C / 09.22.20

10

IOM

4.0 LOCATION OF UNIT

4.1 GENERAL GUIDELINES

FIGURE 3 - SUGGESTED METHOD FOR SUSPENDING HORIZONTAL FURNACE

RETURN AIR PLENUM

ALLOW ENOUGH ANGLE

IRON OVERHANG TO PERMIT

OPENING THE BLOWER DOOR.

• 3/8" THREADED ROD

• 2" (51mm) ANGLE IRON

• JAM NUTS

• LOCK WASHER

• FLAT WASHER

SUPPLY AIR PLENUM

4.2 OTHER CONSIDERATIONS

H8.1.2A

1. Select a location where the exhaust and combustion air piping can be routed between the furnace and

their terminations with a minimum of lengths and ﬁ ttings. Be sure to check that the proposed termination

location will meet code requirements with respect to location and minimum clearances. (See venting

section for minimum and maximum limits.)

2. Select a location as near as possible to the existing or proposed duct system.

3. The furnace location must have provisions for condensate drainage. If a suitable drain is unavailable

near the furnace, a condensate pump must be used. The condensate pump drain tubing must not

terminate outdoors. Be sure to select a condensate pump that has been approved for furnace condensate

applications.

4. The furnace location must permit access for servicing and be within the clearance to combustibles

guidelines as marked on the appliance rating plate.

5. The furnace must be installed on a level surface. It is recommended that the rear of the furnace be

elevated 1/4" (6mm) higher than the front to facilitate proper condensate drainage.

6. If the furnace is being installed so that the return air will enter through the bottom, the perimeter of the

furnace must be properly supported.

7. When installed in the horizontal position, the furnace may be supported from the bottom, or suspended.

(Figure 3)

8. In upﬂ ow right venting conﬁ guration, furnace must drain on the left side.

1. If the furnace is to be located in an area where the combustion air is laden with chemical compounds such

as bromine, chlorine or ﬂ uorine, as may be found in swimming pool chemicals, laundry detergents, etc.,

use outdoor air for combustion. These compounds when exposed to ﬂ ame, form acids which attack the

heat exchanger and other components.

Exposure to the following substances in the combustion air supply (but not limited to the following) will also

require OUTDOOR AIR for combustion:

• Aerosols, particularly CFC based or propelled aerosols

• Air fresheners

W415-2308 / C / 09.22.20

11

IOM

4.3 INSTALLATION IN UPFLOW, DOWNFLOW OR HORIZONTAL POSITIONS

H8.2

• “Airplane Glue” and similar adhesives and cements

• Ammonia, as commonly found in permanent wave solutions used in hair dressing salons

• Anti-static fabric softeners used in clothes dryers

• Carbon tetrachloride

• Chlorinated cleaners and waxes

• Chlorine and bromine based swimming pool chemicals

• De-icing salts or chemicals (rock salt, etc.)

• Dry cleaning ﬂ uids such as perchloroethylene

• Fumes from curing polyurethane and similar substances

• Halogen based refrigerants including R-12 and R-22

• Hydrochloric acid, muriatic acid and other acid based masonry washing and curing materials

• Printer’s inks, paint removers, varnishes, varsol, toluene, etc.

• Water softener salt and chemicals

2. If this furnace is to be installed in an area over a ﬁ nished ceiling or living area, install a ﬁ eld fabricated

auxiliary drain pan under the furnace to protect that area from accidental condensate spills. The auxiliary

pan should be large enough to collect accidentally spilled condensate from the air conditioning evaporator

coil assembly if applicable.

3. If the furnace is installed in an area where freezing may occur, a garage, an attic, a crawl space or any

unconditioned space, steps must be taken to protect the condensate trap and drain line from freezing.

H8.3.2

UPFLOW INSTALLATION: Vent positioning, pressure switch location and drain locations shall be performed in

accordance with instructions in the appropriate sections of this manual.

HORIZONTAL INSTALLATION: Vent positioning, pressure switch location and drain locations shall be performed in

accordance with instructions in the appropriate sections of this manual.

NON-SUSPENDED INSTALLATION: Maintain clearances to combustibles as outlined in Table B. The furnace

must be supported in such a way as to not allow twisting or sagging of the cabinet.

SUSPENDED INSTALLATION: Maintain clearances to combustibles as outlined in Table B. The furnace may

be suspended by ﬁ eld fabricating a cradle of angle iron and threaded rod. Secure the furnace with 2” (51mm)

minimum slotted angle or equivalent as shown in Figure 3. The furnace must be supported in such a way as to

not allow twisting or sagging of the cabinet. Position the supports so as to not interfere with accessing the burner

and blower compartments.

DOWNFLOW INSTALLATION: Vent positioning, pressure switch location and drain locations shall be performed

in accordance with instructions in the appropriate sections of this manual.

The opening in the ﬂ oor must provide adequate clearances to the combustible material according to the

clearance to combustible as outlined in Table B.

IMPORTANT:

• THE FURNACE MUST BE INSTALLED ON A LEVEL SURFACE. IT IS RECOMMENDED

THAT THE REAR OF THE FURNACE BE ELEVATED 1/4” (6mm) HIGHER THAN THE

FRONT TO FACILITATE PROPER CONDENSATE DRAINAGE.

• IF THE FURNACE AND AIR CONDITIONER IS LOCATED ABOVE A FINISHED SPACE,

INSTALL A DRAIN PAN UNDERNEATH THE UNIT.

NOTE

This furnace is approved for installation in attics, alcoves, utility rooms, closets and crawl spaces. If this

furnace is to be installed in a utility room, be sure that it is located in such a way as to allow access for

servicing or the removal of other appliances installed in the room (hot water heater, for example). It is not

permissible to use a rear return on this appliance. Use only side and bottom returns.

W415-2308 / C / 09.22.20

12

IOM

4.4 AIR CONDITIONING

5.0 COMBUSTIBLE CLEARANCES

H9.0

Table B provides the certiﬁ ed clearances to combustibles information. Also see the appliance rating plate

afﬁ xed to the furnace for speciﬁ c model number, serial number and clearance to combustibles information.

IMPORTANT:

THIS FURNACE REQUIRES A MINIMUM OF 24" (610mm) OF FRONT CLEARANCE FOR

SERVICE PURPOSES. FOR THIS PURPOSE, SERVICE CLEARANCE TAKES PRECE-

DENCE OVER CLEARANCE TO COMBUSTIBLES.

H3.97

THIS FURNACE IS CERTIFIED FOR INSTALLATION ON COMBUSTIBLE FLOORS. THIS

SHALL BE INTERPRETED AS A WOOD FLOOR ONLY. FAILURE TO COMPLY WITH THESE

INSTRUCTIONS CAN RESULT IN FIRE, CAUSING PROPERTY DAMAGE, PERSONAL

INJURY OR DEATH.

THE FURNACE MUST NOT BE INSTALLED DIRECTLY ON CARPETING, TILE, OR ANY

COMBUSTIBLE MATERIAL OTHER THAN WOOD FLOORING.

THE AREA AROUND THE FURNACE MUST BE KEPT CLEAR AND FREE OF ALL

COMBUSTIBLE MATERIALS INCLUDING GASOLINE AND OTHER FLAMMABLE VAPORS

AND LIQUIDS.

THE HOMEOWNER SHOULD BE CAUTIONED THAT THE FURNACE AREA MUST NOT BE

USED AS A CLOSET OR FOR ANY OTHER STORAGE PURPOSE.

WARNING

! !

H8.4.4

This furnace may be used as part of an air conditioning system. The furnace wiring and control system is “air

conditioning ready.” There are the following factors to consider:

The air conditioning evaporator coil must be downstream of the heat exchanger. The cooled air passing

over the warmer heat exchanger tubes can cause condensation inside the tubes, resulting in corrosion and

premature failure.

If installing a two stage air conditioning system, clip the JW38 jumper wire between Y (low cool) and Y2 (high

cool) on the furnace control board.

Control defaults to Y2 (high cool) if JW38 jumper wire is NOT cut.

W415-2308 / C / 09.22.20

13

IOM

6.0 DUCTWORK

H10.0A

Proper airﬂ ow is required for the correct operation of this furnace. Insufﬁ cient airﬂ ow may cause erratic

operation, could cause the furnace to cycle on the high temperature limit, and may damage the heat

exchanger. Excessive airﬂ ow may result in an excessively noisy duct system and may result in undesirable

consequences such as creating uncomfortable drafts.

If air conditioning is to be used with the furnace, the duct system must be capable of delivering the correct

amount of airﬂ ow for each system.

The ductwork should be sized and constructed in accordance with accepted industry standards. Duct sizing

and construction information may be obtained from:

• A.C.C.A. (Air Conditioning Contractors of America)

• A.S.H.R.A.E. (American Society of Heating, Refrigeration and Air Conditioning Engineers)

• H.R.A.I. (Heating, Refrigerating and Air Conditioning Institute (Canada)

• S.M.A.C.N.A. (Sheet Metal and Air Conditioning Contractors’ National Association (United States)

All of the above professional organizations have duct sizing manuals available.

The total static pressure drop of the air distribution system (including ﬁ lters) should not exceed 1.0” w.c. or that

speciﬁ ed on product rating plate.

H3.8

DO NOT ALLOW GAS PIPING TO BE ROUTED THROUGH JOIST SPACES THAT ARE

USED FOR RETURN AIR PURPOSES. DO NOT USE JOIST SPACES FOR RETURN AIR

PURPOSES IF THE JOIST SPACE ALREADY CONTAINS PLUMBING STACKS, CHIMNEY

COMPONENTS, ETC. UNLESS THE PORTION USED FOR RETURN AIR PURPOSES CAN

BE COMPLETELY ISOLATED FROM PORTIONS WITH OTHER USAGES.

NEVER ALLOW THE PRODUCTS OF COMBUSTION FROM THE FLUE TO ENTER THE

RETURN AIR OR SUPPLY AIR DUCTWORK.

ALL RETURN AIR DUCTWORK MUST BE ADEQUATELY SEALED AND SECURED TO

THE FURNACE WITH SHEET METAL SCREWS. TAPE THE SHEET METAL SEAMS IN THE

VICINITY OF THE FURNACE WITH DUCT TAPE OR SIMILAR MATERIAL.

WHEN THE FURNACE IS MOUNTED ON A PLATFORM WITH RETURN AIR THROUGH THE

BOTTOM, IT MUST BE SEALED AIR TIGHT BETWEEN THE FURNACE AND THE RETURN

AIR PLENUM. THE FLOOR OR PLATFORM MUST PROVIDE SOUND PHYSICAL SUPPORT

OF THE FURNACE WITHOUT SAGGING OR GAPS AROUND THE BASE. IT MUST ALSO

BE SEALED BETWEEN THE SUPPORT AND THE BASE.

FAILURE TO PREVENT PRODUCTS OF COMBUSTION FROM BEING CIRCULATED INTO

THE LIVING SPACE CAN CREATE POTENTIALLY HAZARDOUS CONDITIONS, INCLUDING

CARBON MONOXIDE POISONING THAT COULD RESULT IN PERSONAL INJURY OR

DEATH.

WARNING

!

W415-2308 / C / 09.22.20

14

IOM

6.1 DUCTWORK STEPS

H10.2

1. Position the furnace to minimize ductwork length and ﬁ ttings.

2. Cut open a return air inlet. The choices are furnace bottom, either side, or any combination thereof (i.e.,

two sides or a side and the bottom).In all cases, cut the return air opening the full width of the return air

markers on the side panel.

NOTE: If the airﬂ ow requirements exceed 1800 cfm, models will require air openings and ﬁ lters on:

• both sides, OR

• one side and the bottom, OR

• just the bottom

3. Connect the return air duct or ﬁ lter ﬁ tting to the furnace. The connection should be sealed air tight to prevent

entraining combustion gases from an adjacent fuel burning appliance, or entraining combustion air for this

furnace or adjacent fuel burning appliances.

4. Ensure that there is adequate space and accessibility for air ﬁ lter removal.

5. If an air conditioning evaporator coil is required, position it on the supply air side of the furnace. Ensure

that no air can bypass the evaporator coil. NOTE: Furnace must NOT be installed downstream of coil.

6. Connect the supply air plenum to the supply air outlet.

FLEXIBLE DUCT CONNECTORS are an effective device to prevent the telegraphing of mechanical noise from

the furnace to other parts of the home via the ductwork. If using ﬂ exible connectors, ensure that the adjoining

duct is independently supported.

H3.9

DO NOT USE THE REAR PANEL AS A RETURN AIR INLET. THERE IS INSUFFICIENT

ROOM TO PERMIT ADEQUATE AIRFLOW.

DAMAGES, DEFECTS OR FAILURES CAUSED BY CONDITIONED AIR (RETURN AIR)

SUPPLIED TO THE FURNACE BEING GREATER THAN 20% FROM OUTDOORS (55°F/13°C

MIN. RETURN AIR TEMPERATURE).

SOME HEATING AIR FLOW VALUES MAY BE HIGHER THAN THOSE REQUIRED FOR

COOLING. BE SURE TO SIZE DUCT SYSTEM FOR HIGHEST POSSIBLE VALUES.

WARNING

!

W415-2308 / C / 09.22.20

15

IOM

7.2 ACCEPTABLE MATERIALS IN UNITED STATES

7.0 VENTING AND COMBUSTION PIPING

7.1 ACCEPTABLE MATERIALS IN CANADA

H3.10

READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS IN THIS SECTION. FAILURE TO

PROPERLY VENT OR SUPPLY COMBUSTION AIR TO THIS FURNACE CAN CAUSE CAR-

BON MONOXIDE POISONING, OR AN EXPLOSION OR FIRE, RESULTING IN PROPERTY

DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

WARNING

!

H11.2B

Furnace venting may be comprised of:

• Schedule 40 PVC, ASTM D1785 or CSA B137.3

• PVC-DWV, ASTM D2665 or CSA B181.2

• Schedule 40 CPVC, ASTM F441 or CSA B137.6

• PVC PRIMER AND SOLVENT CEMENT: ASTM D2564

• PPE ULC S636 Manufactured by M&G Duravent - must terminate using 45 and 90 degree elbows, or

a tee.

Follow piping manufacturers instructions on proper installation of piping and ﬁ ttings including cutting, deburring

,

priming, cementing, curing and supporting.

H11.2

Effective August 1, 2007, all vent piping materials and ﬁ ttings for ﬂ ue gas venting must be ULC S636 listed

and identiﬁ ed as such on the material. The ﬁ rst 3ft. (900mm) of venting must be readily available for visual

inspection. Speciﬁ ed primers and glues of the certiﬁ ed vent system must be from a single system manufacture,

and not intermixed with other system manufacture’s vent system parts. The components of the certiﬁ ed vent

system must not be interchanged with other vent systems, or unlisted pipe, and or ﬁ ttings. Follow the venting

manufacturers instructions on installation, cutting, de-burring, cementing, curing and supporting of the venting

system.

Furnace must be vented with ULC S636 certiﬁ ed PVC manufactured by IPEX, and Royal Building Products

(GVS-65 & GVS90), or ULC S636 certiﬁ ed PPE manufactured by M&G Duravent.

PVC vent terminations may use concentric kits listed in section 10.3 - or terminate using 45 and 90 degree

elbows, or a tee.

PPE venting must terminate using 45 and 90 degree elbows.

Minimum rating of 149 degrees F (65°C).

NO ‘B’ VENT APPLICATIONS ALLOWED.

W415-2308 / C / 09.22.20

16

IOM

7.3 VENT DRAIN OPTION

H11.3A

A vent drain is recommended when vent passes through any unconditioned space such as an attic or crawl

space in order to prevent the accumulation of excess condensate in the inducer housing during operational

cycles, refer to images for Vent Drain Option.

To install the vent drain, complete the following steps:

IMPORTANT: Tee, reducer and nipple must be properly

cemented together using the appropriate method

and materials speciﬁ ed in section 7.0 Venting and

Combustion Piping; 7.1 Acceptable Materials in Canada

and 7.2 Acceptable Materials in United States.

1. Place a tee of the proper diameter for the vent system

being installed 2" (51mm) or 3" (76mm) in the horizontal run

or vertical riser closest to the furnace.

2. Place a reducer bushing of proper diameter in the stem

portion of the tee. The recommended size for the reducer is

5/8" (15.9mm).

3. Place a piece of 5/8" (15.9mm) diameter pipe that has a

minimum length of 3" (76mm) long into the reducer to serve

as a nipple.

4. Connect a piece of ﬂ exible drain tubing such as EPDM

rubber or PVC to the nipple.

5. Loop the drain tubing to provide a trap.

6. Connect the discharge end of the drain tube to the

condensate disposal system externally to the furnace.

IMPORTANT:

ELBOWS WITH DRAIN PORTS

ARE NOT RECOMMENDED, AS

CONDENSATE CAN BYPASS THE

DRAIN ON THE CURVE.

1/2" (12.7mm) ID MAX.

3" (76mm) MIN.

10" (254mm) MAX.

LOOP DIAMETER

ATTACH THIS END TO

CONDENSATE DRAIN

SYSTEM

3" (76mm) MIN.

10" (254mm) MAX.

LOOP DIAMETER

ATTACH THIS END TO

CONDENSATE DRAIN

SYSTEM

1/2" (12.7mm) ID MAX.

USE SWEEP TEE ON

HORIZONTAL LINE

H11 3A

NOTE: Any increase of venting diameter must be done on the vertical sections NOT horizontal sections.

W415-2308 / C / 09.22.20

17

IOM

8.0 NON-DIRECT VENT FURNACE INSTALLATIONS USING

INDOOR COMBUSTION AIR (ONE PIPE SYSTEM)

The furnace, although designed as a direct vent type appliance, may be installed with the intake vent inside th

e

structure.

Adequate provisions for combustion and ventilation air must be in accordance with CAN/CGA-B149 in Canada,

and ANSI Z223.1 - 2018, section “Air for Combustion and Ventilation,” in the United States. Check with local

authorities for any additional building codes bylaws or regulations.

AIR FOR COMBUSTION AND VENTILATION PURPOSES MUST NOT ORIGINATE FROM A

CORROSIVE ATMOSPHERE. ANY FURNACE FAILURE CAUSED BY CORROSIVE ELEMENTS IS

EXCLUDED FROM WARRANTY COVERAGE.

CAUTION

!

The following types of installation sites (but not limited to the following) will REQUIRE OUTDOOR AIR for

combustion because of chemical exposures:

• Commercial buildings

• Buildings with indoor swimming pools

• Furnaces installed in laundry rooms

• Furnaces in hobby or craft rooms

• Furnaces installed near chemical storage areas

H3.11

THIS FURNACE AND ANY OTHER FUEL BURNING APPLIANCE MUST BE PROVIDED

WITH ENOUGH FRESH AIR FOR PROPER COMBUSTION AND VENTILATION OF THE

FLUE GASES. MOST HOMES WILL REQUIRE THAT OUTSIDE AIR BE BROUGHT TO

THE FURNACE AREA. FAILURE TO DO SO CAN CAUSE PERSONAL INJURY, OR DEATH

FROM CARBON MONOXIDE POISONING.

WARNING

!

H13.0A

Combustion air must be free of acid forming chemicals such as sulphur, ﬂ uorine and chlorine. These elements

are found in aerosol sprays, detergents, bleaches, cleaning solvents, air fresheners, paint and varnish

removers, refrigerants, and many other commercial and household products. When burned in a gas ﬂ ame,

vapors from these products form acid compounds. Acid compounds increase the dew point temperature of the

ﬂ ue products and are highly corrosive after they condense.

8.1 DETERMINING COMBUSTION AIR

8.1.1 CASE 1: FURNACE LOCATED IN A UNCONFINED SPACE

H13.1

Unconﬁ ned space does not necessarily mean that ventilation will not have to be introduced from the outdoors,

particularly in airtight homes. The minimum requirement for unconﬁ ned space is a volume of 50 cubic feet (1.42

m³) for each 1000 Btu/hr for all fuel burning appliances located within the unconﬁ ned area.

If the amount of combustion and ventilation air is insufﬁ cient to properly operate the furnace and other fuel

burning appliances within the unconﬁ ned area, it will be necessary to supply it from the outdoors based on the

criteria used when calculating the air supply for a conﬁ ned space.

NOTE

If planning to use the inside air in an unconﬁ ned space, remember to test for proper furnace operation (as well

as other fuel burning appliances located within the unconﬁ ned space) with respect to adequate combustion and

ventilation air with ﬁ replace dampers open, clothes dryer running, bathroom exhaust fans on, kitchen range hood

on, etc.

W415-2308 / C / 09.22.20

18

IOM

8.1.2 CASE 2: FURNACE LOCATED IN A CONFINED SPACE

H13.2D

A conﬁ ned space, (any space smaller than the minimums discussed in Case 1), must have two air openings;

one within 12” (305mm) of the ceiling and the other within 12” (305mm) of the ﬂ oor. The air openings must be

sized considering the method outside air is introduced, whether the combustion and ventilation air is being

taken from indoors or outdoors and taking into account any other fuel burning appliances in the conﬁ ned

space.

If sufﬁ cient indoor combustion and ventilation air is available for the furnace and all other fuel burning

appliances, size each opening on the basis of one square inch (645mm²) of free area per 1000 Btu/hr.

(Figure 4)

NOTE

Be sure to consider all clothes dryers, bathroom fans, range hoods, etc., when making this calculation.

The minimum requirement for these openings is 100

square inches (645mm²), even for the furnace models

under 100,000 Btu/hr.

NOTE

If using grills to cover the two openings, factor in the

free area of the grill. Typically, a sidewall grill will

have a free area approximately 50% of its nominal

size. Consequently, if the required opening is 10" x

10" (254mm x 254mm), it will have to be doubled if

using a sidewall grill with 50% free area.

IMPORTANT:

IF AN EXHAUST FAN, FIREPLACE, CLOTHES DRYER OR ANY SIMILAR DEVICE IS PRESENT IN THE

INDOOR AREA FROM WHICH THE COMBUSTION AND VENTILATION AIR WILL BE DRAWN, NEGA-

TIVE PRESSURE COULD BE A PROBLEM IF NATURAL INFILTRATION FROM THE OUTDOORS DOES

NOT MATCH THE RATE AT WHICH AIR IS EXHAUSTED.

FIGURE 4 - COMBUSTION/DILUTION AIR FROM

HEATED INSIDE SOURCES (CASE 2)

8.1.3 CASE 3: FURNACE LOCATED IN A CONFINED SPACE, OUTDOOR AIR FROM ATTIC

OR CRAWL SPACE

In this circumstance, the free area of each of the two combustion and ventilation air openings is based on a

minimum of 1 square inch (645mm²) per 4000 Btu/hr. In this conﬁ guration, one opening can originate from the

ﬂ oor drawing combustion and ventilation air from the ventilated crawl space.

The other opening may communicate freely with the ventilated attic. If using the attic air, ensure that the

opening is ducted from the ceiling high enough to be above the insulation. The attic must be adequately

vented with sofﬁ t vents or gable vents (Figure 5).

As an alternative to creating an opening in the ﬂ oor to draw air from a crawl space, a duct may be dropped from

the attic terminating 12” (305mm) above the ﬂ oor.

W415-2308 / C / 09.22.20

19

IOM

H13.3C

FIGURE 5 - OUTSIDE AIR FOR COMBUSTION, ATTIC OR

CRAWL SPACE (CASE 3)

Alternate Combustion Air

from Attic. (12” / 305 mm

above oor)

The following table shows minimum free areas and round pipe sizes when drawing combustion air vertically

from the attic or crawl space for the furnace

only. If other fuel burning appliances are

present, their combustion air and ventilation

air requirements must be added to those of

the furnace.

IMPORTANT:

IF THE ATTIC HAS AN EXHAUST FAN (POWER VENT), IT MAY CREATE A NEGATIVE

PRESSURE SUFFICIENTLY LARGE ENOUGH TO PREVENT THE ATTIC FROM BEING

AN EFFECTIVE SOURCE OF COMBUSTION AND VENTILATION AIR. POWERED ATTIC

FANS DO NOT CUSTOMARILY RUN DURING THE HEATING SEASON; HOWEVER,

SOME ARE CONTROLLED BY A HUMIDISTAT AS WELL AS A THERMOSTAT, WHICH MAY

ALLOW SOME OPERATION DURING THE HEATING SEASON. THE CHOICES ARE (A)

USE THE DIRECT VENT OPTION; (B) OBTAIN OUTDOOR AIR FROM ELSEWHERE; OR

(C) INTERLOCK THE ATTIC EXHAUST FAN WITH THE FURNACE SUCH THAT THE TWO

CANNOT OPERATE SIMULTANEOUSLY.

8.1.4 CASE 4: FURNACE LOCATED IN A CONFINED SPACE, OUTDOOR AIR DUCTED

HORIZONTALLY

Similar to Case 3, outdoor air for combustion and ventilation may be drawn through horizontal ducting. The

free area for each opening is calculated on the basis of a minimum of 1 square inch (645mm²) per 2000 Btu/hr

input.

The following table shows minimum free areas and round pipe sizes when drawing combustion air horizontally

from the outdoors for the furnace only. If other fuel burning appliances are present, their combustion air and

ventilation air requirements must be added to those of the furnace.

Combustion Air

Duct Terminates

12” (305mm)

above oor.

FIGURE 6 - OUTDOOR AIR FOR COMBUSTION,

HORIZONTAL (CASE 4)

TABLE 2 - VERTICAL AIR SUPPLY (CASE 3)

Input Free Area

Round Pipe Size

K/Btu/hr Ea. Opening

40

15 in.² (97cm²) 5 in. (127mm)

60

80 20 in.² (129cm²)

6 in. (152mm)

100 25 in.² (161cm²)

120 30 in.² (194cm²) 7 in. (178mm)

H12.16.7A

TABLE 3 - HORIZONTAL AIR

SUPPLY (CASE 4)

Input

K/Btu/hr

Free Area

Ea. Opening

Round Pipe

Size

40

30 in

2

(194cm

2

)

7 in

(178mm)

60

80

40 in

2

(258cm

2

)

8 in

(203mm)

100

50 in

2

(323cm

2

)

120

60 in

2

(387cm

2

)

9 in

(229mm)

H12.9.7A

W415-2308 / C / 09.22.20

20

IOM

8.1.5 CONNECTION TO FURNACE NON-DIRECT VENT

H13.4C

IMPORTANT:

IF GRILLS ARE USED ON THE OUTSIDE WALL, THEY MUST BE SIZED PROPERLY.

MOST SIDEWALL GRILLS HAVE ONLY 50% FREE AREA. IN THE CASE OF A UNIT WITH

100,000 BTU/HR INPUT, WHICH REQUIRES A PAIR OF 8” (203mm) ROUND PIPES TO

OBTAIN SUFFICIENT COMBUSTION AND VENTILATION AIR, THE DUCT COULD BE AN

EQUIVALENT RECTANGULAR DUCT; 8” X 7” (203mm X 178mm) FOR EXAMPLE. BASED

ON 50% FREE AREA FOR THE INLET GRILLS, THE ACTUAL GRILL SIZE WOULD HAVE

TO BE 14” X 8” (356mm X 203mm) OR ITS EQUIVALENT. A TRANSITION MAY BE USED TO

REDUCE TO THE SMALLER DUCT SIZE IF NECESSARY.

IMPORTANT:

THE OUTDOOR GRILLS MUST BE INSTALLED IN A LOCATION WHERE THEY WILL NOT BE

OBSTRUCTED IN ANY MANNER.

H13.5C

FIGURE 7 - NON-DIRECT

COMBUSTION AIR INLET

IMPORTANT:

WHEN USING INDOOR AIR OR THE NON-DIRECT

VENT CONFIGURATION, THE COMBUSTION AIR

INLET TO THE FURNACE MUST BE PROTECTED

FROM BLOCKAGE. USE A DOUBLE ELBOW

ARRANGEMENT IF SUPPLYING COMBUSTION AIR

THROUGH THE TOP, OR A DOWNWARD POINTING

SINGLE ELBOW IF SUPPLYING COMBUSTION AIR

THROUGH THE SIDE. (FIGURE 7)

La page est en cours de chargement...

NAPOLEON WPV080T3AA-N Manuel utilisateur

Ce manuel convient également à

NAPOLEON WPV080T3AA-N Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents