Candy CDG6CMBGWIFI/1 Manuel utilisateur

Candy
Marque
Candy
Modèle
CDG6CMBGWIFI/1
Catégorie
Hottes
Taper
Manuel utilisateur
1
CDG6CMBGWIFI/1
Cooker Hood
Instruction Manual
2
Content
1…………………………………..………………………………Safety instructions
2…………………………………..………………………………Installation
3…………………………………..………………………………Start using your cooker hood
4…………………………………..………………………………Troubleshooting
5…………………………………..………………………………Maintenance and cleaning
6…………………………………..………………………………Environment protection
3
SAFETY INSTRUCTIONS
This manual explains the proper installation and use of your cooker hood,
please read it carefully before using even if you are familiar with the product.
The manual should be kept in a safe place for future reference.
Never to do:
● Do not try to use the cooker hood
without the grease filters or if the filters
are excessively greasy!
●Do not install above a cooker with a
high level grill.
●Do not leave frying pans unattended
during use because overheated fats or
oils might catch fire.
●Never leave naked flames under the
cooker hood.
●If the cooker hood is damaged, do not
attempt to use.
●Do not flambé under the cooker hood.
●CAUTION: Accessible parts may
become hot when used with cooking
appliances.
●The minimum distance between the
supporting surface for the cooking
vessels on the hob and the lowest part
of the cooker hood. (When the cooker
hood is located above a gas appliance,
this distance shall be at least 65 cm)
●The air must not be discharged into a
flue that is used for exhausting fumes
from appliances burning gas or other
fuels. Cooker hoods and other cooking
fume extractors may adversely affect
the safe operation of appliances
burning gas or other fuels (including
those in other rooms) due to back flow
of combustion gases. These gases
can potentially result in carbon
monoxide poisoning. After installation
of a cooker hood or other cooking
fume extractor, the operation of open
flued gas appliances should be tested
by a competent person to ensure that
back flow of combustion gases does
not occur.
Always to do:
● Important! Always switch off the
electricity supply at the mains during
installation and maintenance such as
light bulb replacement.
●The cooker hood must be installed in
accordance with the installation
instructions and all measurements
followed.
●All installation work must be carried
out by a competent person or qualified
electrician.
●Please dispose of the packing material
carefully. Children are vulnerable to it.
● Pay attention to the sharp edges
inside the cooker hood especially
during installation and cleaning.
●Make sure the ducting has no bends
sharper than 90 degrees as this will
reduce the efficiency of the cooker
hood.
●Warning: Failure to install the screws
or fixing device in accordance with
these instructions may result in
electrical hazards.
●Warning: Before obtaining access to
terminals, all supply circuits must be
disconnected.
4
●If the voltage rating of the lamp is less
than the rated voltage of the appliance,
the voltage rating of the lamp shall
also be marked on or near the lamp
holder.
Always to do:
●Always put lids on pots and pans
when cooking on a gas cooker.
●When in extraction mode, air in the
room is being removed by the cooker
hood. Please make sure that proper
ventilation measures are being
observed. The cooker hood removes
odours from room but not steam.
●There shall be adequate ventilation of
the room when the range hood is used
at the same time as appliances
burning gas or other fuels.
●Cooker hood is for domestic use only.
●If the supply cord is damaged, it must
be replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid a hazard.
●This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been
given supervision or instruction
concerning use of the appliance by a
person responsible for their safety
●Children should be supervised to
ensure that they do not play with the
appliance.
●This appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or lack
of experience and knowledge if they
have been given supervision or
instruction concerning use of the
appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
Always to do:
● Caution: The appliance and its
accessible parts can become hot
during operation. Be careful to avoid
touching the heating elements.
Children younger than 8 years old
should stay away unless they are
under permanent supervision.
●There is a fire risk if cleaning is not
carried out in accordance with the
instructions.
●Regulations concerning the discharge
of air have to be fulfilled.
●Clean your appliance periodically by
following the method given in the
chapter MAINTENANCE.
●For safety reason, please use only the
same size of fixing or mounting screw
which are recommended in this
instruction manual.
●Regarding the details about the
method and frequency of cleaning,
please refer to maintenance and
cleaning section in the instruction
manual.
●Regarding the information about how
the appliance is to be fixed to its
support, please refer to Operation
section, the Installation procedures in
this manual.
●Cleaning and user maintenance shall
not be made by children without
supervision.
5
●When the range hood and appliances
supplied with energy other than
electricity are simultaneously in
operation, the negative pressure in the
room must not exceed 4 Pa (4 x 10-5
bar).
●WARNING: Danger of fire: do not
store items on the cooking surfaces.
●A steam cleaner is not to be used.
●NEVER try to extinguish a fire with
water, but switch off the appliance and
then cover flame e.g. with a lid or a
fire blanket.
INSTALLATION (VENT OUTSIDE)
MOUNTING OF THE V-FLAP
If the cooker hood does not have an assembled V-flap 1, you should mount the half-
parts to its body.The images only show an example of how to mount the V-flap,
because the outlet may vary according to different models and configurations.
To mount the V-flap 1 you should:
• Mount two half-parts 2 into the body 6
• the pin 3 should be top oriented;
• the axis 4 should be inserted into the holes 5 on the body;
• repeat all the operations for the 2nd half-part.
6
INSTALLATION
If you have an outlet to the outside, your cooker hood can be connected as below
picture by means of an extraction duct (enamel, aluminum, flexible pipe or non-
flammable material with an interior diameter of 150mm)
1. Before installation, turn the unit off.
2. The cooker hood should be placed at a distance of 65~75cm above the cooking
surface for best effect.
3. After decide the cooker hood height, measure the position of the holes for hanging
hood,inside chimney bracket ,outside chimney bracket and safety holes. Drill 8 φ8
holes and insert wall plugs into the holes. Fix the inside chimney bracket on the
wall with 2pcs ST4 x 40mm screws.Screw 2pcs ST4 x 8mm screws in the hole for
hanging the hood body and the screws installed should leave for 3-5mm out of the
wall to hang the hood.The fixed position of the inside chimney bracket is the
highest place of chimney. See pic 2.
7
4. Install the v-flap and expansion pipe onto the cooker hood. Fix the expansion pipe
on the outlet with a cable tie. Please note: The expansion pipe and v-flap are
not included in the product. See Pic 3.
5. Hang the cooker hood onto the hook.See pic 4.
6. Install the outside chimney bracket onto the outside chimney with 2pcs ST4*8mm
screws, here should be sure the inside chimney can be flexed freely.See Pic 5.
7. Fix the cooker hood with 2pcs ST4*30mm safety screws. Note: The two safety
vents are positioned on the back housing, with a diameter of 6mm.Put the two
chimneys onto the cooker hood, fix the outside chimney on the wall with 2pcs
ST4*40mm screws and lead the expansion pipe to the outside. See pic 6.
8. Adjust the height of the inside chimney to the position of the inside chimney bracket
and fix it with 2pcs ST4*8mm screws. Fix the outside chimney onto the hood body
with 2pcs ST4*8mm screws.See Pic 7.
Electrical Installation
All installation must be carried out by a competent person or qualified electrician.
Before connecting the mains supply ensure that the mains voltage corresponds to the
voltage on the rating plate.
8
Direct Connection
The appliance must be connected directly to the mains using an
omnipolar circuit breaker with a minimum opening of 3mm between
the contacts.
The installer must ensure that the correct electrical connection has
been made and that it complies with the wiring diagram.
The cable must not be bent or compressed.
Regularly check the power plug and power cord for damage. If the
supply cord is damaged, it must be replaced by a special cord or
assembly available from the manufacturer or its service agent.
WARNING: This is a Class I appliance and MUST be earthed
This appliance is supplied with a 3 core mains cable coloured as
follows:
Brown = L or Live
Blue = N or Neutral
Green and Yellow = E or Earth
HINTS FOR EXHAUST DUCT INSTALLATION
The following rules must be strictly followed to obtain optimal air extraction:
• Keep expansion pipe short and straight.
• Do not reduce the size or restrict the expansion pipe.
• When using the expansion pipe always install the pipe pulled taut to minimize
pressure loss.
• Failure to observe these basic instructions will reduce the performance and
increase noise levels of the cooker hood.
• Any installation work must be carried out by a qualified electrician or competent
person.
• Do not connect the ducting system of the hood to any existing ventilation system
which is being used for any other appliance ,such as warmer tube, gas tube , hot
wind tube.
• The angle of the bend of the expansion pipe should not be less than 120º; you
must direct the pipe horizontally, or, alternatively, the pipe should go up from the
initial point and should be led to an outer wall.
• After the installation ,make sure that the cooker hood is level to avoid grease
collection at on end.
• Ensure the expansion pipe selected for installation complies with relevant
standards and is fire retardant.
Ensure the exhaust ducting selected for installation complies with relevant standards
and is fire retardant.
9
WARNING:
➢ For safety reason, please use only the same
size of fixing or mounting screws which are
recommended in this instruction manual.
➢ Failure to install the screws or fixing device in
accordance with these instructions may result in
electrical hazards.
Start Using Your Cooker Hood
Touch control+WIFI
There are four icons: (Time delay), (Lamp), (Speed), (WIFI). See
picture above.
1. Power on: After power supply to the hood, the backlight of all icons will turn on and
the buzzer sounds once. Then output shut off, the hood enters into stand-by mode.
2. Lamp icon :
Short press (Lamp) icon, the illuminating lamps and lamp icon indicator will light up.
Short press again, the illuminating lamps and lamp icon indicator will be off. The above
steps can be operated repeatedly.
3. (Speed) icon:
The cooker hood has three speed levels ,they are low,mid,high, and the
corresponding LED display will be”1”,”2”,”3”.
3.1 Press (Speed) icon once, the indicator lights of this icon will be on and the
hood starts to work at low speed and the LED display will display “1”.
3.2 Press (Speed) icon again when it works at low speed, the cooker hood
works at mid speed and the LED display will display “2”.
3.3 Press (Speed) icon again when it works at mid speed, the cooker hood at
the high speed and the LED display will display “3”.
3.4 During the working, you can press (Speed) icon to change the speed
circularly: “low→mid→high→off→low→mid……”
4. ( Time delay) icon:
4.1 The time delay icon is only used for the time delay function when the hood is
working. (Press this icon will be invalid when the hood is under standby mode or just
10
turn on the lamp). Press this button once, the set time is 5 minutes and the indicator
light of this button will lit on. Press this button once again will turn off the time delay
function and the indicator light will turn off. The above steps can be operated
repeatedly. After the set delay time is completed, the cooker hood will be turn off and
the light will be off.
4.2 When the delay function is set, if adjusting the speeds, will automatically exit the
delay function.
5. (WIFI) icon:
5.1 When first time power supply to the hood, the WIFI button slowly flashes for 3
mins, it indicates no connecting to the network, if no operation to connect the network,
the WIFI button will stop flashing after 3mins.
5.2 Operate in mobile APP, when it indicates to have the WIFI button quickly flashes,
long press the WIFI button for 3s to enter into the network connecting status, the WIFI
button will quickly flashes, then operate in APP to finish the connecting. After
connecting network, the WIFI button will stop quickly flashing. When the hood is
working, the WIFI button indicator will keep lighting on to display the network is well
connecting.
WIFI + BLE function
1. Search hOn APP in the mobile application market, click to download and install.
2. Open the hOn APP, if you do not have an account, you need to register a new user
account. After completing the registration, enter the account and password to log in.
3. Then log into the hOn APP account, click to add and select the cooker hood item.
The first step is to select the WIFI network and enter the password. Then press
the (WiFi) icon, it will start blinking. After the pairing process, the WiFi icon will be
on.
4. After the pairing process has been successful completed, click on the hood card on
the hOn App and you can use the APP function keys to control the working status of
the hood.
TROUBLESHOOTING
11
Fault
Possible Cause
Solution
Light on, but motor
does not work
Fan switch turned off
Select a fan switch position.
Fan switch failed
Contact service center.
Motor failed
Contact service center.
Light does not
work, motor does
not work
House fuses blown
Reset/Replace fuses.
Mains power cable is loose or
disconnected
Refit mains power cable to
power outlet.
Switch power outlet on.
Oil leakage
One way valve and the outlet
are not tightly sealed
Take down the one way valve
and seal with sealant.
Leakage from the connection of
chimney and cover
Take chimney down and seal.
Lights not working
Broken or faulty bulbs
Replace bulbs as per this
instruction.
Insufficient suction
The distance between the
cooker hood and the gas top is
too far
Refit the cooker hood to the
correct distance.
The Cooker hood
inclines
The fixing screw is not tight
enough
Tighten the hanging screw and
make it horizontal.
NOTE:
Any electrical repairs to this appliance must conform to your local, state and
federal laws.Please contact the service centre if in any doubt before
undertaking any of the above.Always disconnect the unit from the power source when
opening the unit.
MAINTENANCE AND CLEANING
Caution:
• Before maintenance or cleaning is carried out, the cooker hood should be
disconnected from the mains power supply. Ensure that the cooker hood is switched
off at the wall socket.
• External surfaces are susceptible to scratches and abrasions, so please follow the
cleaning instructions to ensure the best possible result is achieved without damage.
GENERAL
Cleaning and maintenance should be carried out with the appliance cold especially
when cleaning.Avoid leaving alkaline or acid substances (lemon juice, vinegar etc.) on
the surfaces.
STAINLESS STEEL
The stainless steel must be cleaned regularly (e.g.weekly) to ensure a long life
12
expectancy.Dry with a clean soft cloth. A specialized stainless steel cleaning fluid may
be used.
NOTE:
Ensure that wiping is done along with the grain of the stainless steel to prevent any
unsightly crisscross scratching patterns from appearing.
CONTROL PANEL SURFACE
The inlay control panel can be cleaned using warm soapy water. Ensure the cloth is
clean and well wrung before cleaning. Use a dry soft cloth to remove any excess
moisture left after cleaning.
Important
Using neutral detergents and avoid using harsh cleaning chemicals, strong household
detergents or products containing abrasives,as this will affect the appearance of the
appliance and potentially remove any printing of artwork on the control panel and will
void manufactures warrantee.
GREASE MESH FILTERS
The mesh filters can be cleaned by hand. Soak them for about 3 minutes in water with
a mild detergent and then brush it gently with a soft
brush. Do not apply too much pressure so as to avoid
any damage to it. (Leave to dry naturally out of direct
sun light)
Filters should be washed separately to crockery and
kitchen utensils. It is advisable not to use rinse aid.
Following the picture beside to dismantle the grease
filter.
INSTALLING GREASE MESH FILTERS
• To install filters for the following four steps:
- Angle the filter into the slots at the back of the hood.
- Push the button on the handle of the filter.
- Release the handle once the filter fits into a resting position.
- Repeat to install all filters.
CARBON FILTER- not supplied
Activated carbon filter can be used to trap odors. Normally the activated carbon filter
should be changed every 3 to 6 months according to your cooking habits. The
installation procedure of activated carbon filter is as below:
1. Before installing or replacing the carbon filters, please disconnect mains power
to the unit.
2. Press the filter lock and remove the mesh filter.
3. Turn the carbon filter on both sides of the motor anti-clockwise. Replace the
carbon filters with the new carbon filters.
4. Place the mesh filter.
5. Connect the power supply to the wall socket.
13
NOTE:
• Make sure the filter is securely locked. Otherwise, it would loosen and cause
danger.
• When activated carbon filter attached, the suction power will be lowered.
BULB REPLACEMENT
Important :
The bulb must be replaced by the manufacturer, its
service agent or similarly qualified persons.
Always switch off the electricity supply before
carrying out any operations on the appliance. When
handling bulb, make sure it has completely cooled
down before any direct contact with hands.
When handling bulbs hold with a cloth or gloves to
ensure perspiration does not come in contact with
the bulb as this can reduce the life of the bulb.
Note:
⚫ Before replacing light that the cooker hood can be isolated from the supply
mains by means of a plug or an all-pole switch.
⚫ Protect against danger when changing lights, such as wearing gloves.
Changing the lights:
➢ Remove the grease filter.
➢ Way 1. Use a tool or the hand to press the spring splinter of both sides of LED light
to the inside, until the light is pressed out, see pic 1.Then slightly pull the light
connecting wire out, and dismantle the terminal of the light connecting wire. See
pic 2.
Way 2.Use straight screwdriver to prize up the LED light bottom edge, see pic 3,
then slightly pull out the LED light and light connecting wire. See pic 2.
➢ Apply the reverse procedure to install the light back.
• ILCOS D code for this lamp is: DSS-1.5/65-S-120/33
– LED modules –rectangle LED lamp
– Max wattage: 1×1.5W
– Voltage range: DC 12V
– Dimensions:
14
ENVIRONMENTALPROTECTION:
This appliance is labelled in accordance with European Directive 2012/19/EU
regarding electric and electronic appliances (WEEE). The WEEE contain both
polluting substances (that can have a negative effect on the environment) and
base elements (that can be reused). It is important that the WEEE undergo
specific treatments to correctly remove and dispose of the pollutants and recover
all the materials. Individuals can play an important role in ensuring that the
WEEE do not become an environmental problem; It is essential to follow a few
basic rules:
-the WEEE should not be treated as domestic waste;
-the WEEE should be taken to dedicated collection areas managed by the town council or
aregistered company.
In many countries, domestic collections may be available for large WEEEs. When you buy a
new appliance, the old one can be returned to the vendor who must accept it free of charge as
a one-off, as long as the appliance is of an equivalent type and has the same functions as the
purchased appliance.
NOTE:
The following shows how to reduce total environmental impact (e.g. energy use) of the
cooking process).
(1) Install the cooker hood in a proper place where there is efficient ventilation.
(2) Clean the cooker hood regularly so as not to block the airway.
(3) Remember to switch off the cooker hood light after cooking.
(4) Remember to switch off the cooker hood after cooking.
INFORMATION FOR DISMANTLING
Do not dismantle the appliance in a way which is not shown in the user manual. The
appliance could not be dismantled by user. At the end of life, the appliance should
not be disposed of with household waste. Check with your Local Authority or retainer
for recycling advice.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Candy CDG6CMBGWIFI/1 Manuel utilisateur

Candy
Marque
Candy
Modèle
CDG6CMBGWIFI/1
Catégorie
Hottes
Taper
Manuel utilisateur
Télécharger le PDF
rapport

Documents connexes

Autres documents