Paslode CFN325XP Manuel utilisateur

Model CFN325XP

2019

Part No. 906300

906318

11/19

It is the customerʼs responsibility to have

all operators and service personnel read

and understand this manual.

Model B20580

Part No.

906400

Model CF325IM

Part No.

905800

2

Introduction

Paslode Cordless Framing Nailer

Operating Manual

1. READ THE MANUAL FROM COVER TO COVER

BEFORE USING THE TOOL.

2. FOLLOW ALL INSTRUCTIONS IN THE MANUAL.

My Paslode representative is:

Name

Address

piZ etatSytiC

Telephone Number

My Service & Repair Center is:

Name

Address

piZ etatSytiC

Telephone Number

This manual is intended to acquaint you with the

Paslode Cordless Framing Nailer. Unlike other power

fastening tools, the Cordless Framing Nailer is powered

by an internal combustion linear motor. In simpler

terms, your Cordless Framing Nailer is powered by a

motor similar to the one that powers an automobile. The

Cordless Framing Nailer ignites a fuel and air mixture to

produce the energy to drive the motor, which in turn

drives the fastener. As you will see, the Cordless Fram-

ing Nailer is totally self-contained. It carries its own fuel

supply and battery, along with a supply of fasteners.

For ease of use, this manual is divided into sections

(see Contents). Each section of the manual is written

with you, the tool operator, in mind. We have left out all

of the technical terms so that you can readily under-

stand how to get the maximum performance from your

Cordless Framing Nailer, and how to avoid damaging

the tool or injuring yourself. But, to accomplish this, we

need you to do two things:

The Cordless Framing Nailer should be handled like other

power fastening tools that you use. Like most tools, when

used improperly it could result in injury. If you are going to

allow others to use the Cordless Framing Nailer, it is your

responsibility to make sure that they also read and comply

with the instructions in this manual before attempting to

operate the tool.

Should you have questions about the Cordless Framing

Nailer, or wish to obtain additional copies of this

manual, please contact your Paslode®

representative. The

space below is provided so that you may record your

representative's name, address, and telephone number.

®

Contents

egaPtcejbuS

Introduction................................................................................ 2

An Overview of the Paslode Cordless Framing Nailer ...............4

Safety Instructions......................................................................5

Battery and Charging System ................................................... 8

Fuel Cell and Metering Valve .................................................. 10

.........13

Paslode Cordless Framing Nailer Operation........................... 14

Fasteners and Applications ..................................................... 15

Servicing ................................................................................. 16

Troubleshooting ...................................................................... 18

...................................................................... 20

The battery charger meets all safety requirements for power

tools.

is a trademark

Power Nailers are made in the U.S.A.

Paslode® is a member of:

Preparing the Paslode Cordless Framing Nailer for Use

RBRC

Li-ion

USA

An Illinois Tool Works Co.

155 Harlem Avenue

Glenview, IL 60025

www.paslode.com

Cleaning Procedure URL

4

An Overview of the Paslode Cordless Framing Nailer

Description

The Paslode Cordless Framing Nailer

is a self-contained,

fully portable nailer that uses liquid hydrocarbon fuel to

power a unique linear drive internal combustion motor.

As with any internal combustion motor, the Paslode Cordless

Nailer will require periodic maintenance to keep it operating

at it's peak performance. The cleaning procedure booklet

will instruct you on the proper cleaning of your tool. If

additional services are required, contact your local Paslode

service provider.

Specifications

Dimensions: Weight (with battery) 7.2 pounds (3.2 Kg)

Height 14-1/2 inches (368mm)

Length 12 inches (305mm)

Cycle Rate:

Intermittent Operation – 2 to 3 nails/second

Maximum Cycle Rate:

1,000 shots per hour

NOTE: Exceeding these rates could cause tool to

overheat,

resulting in loss of performance or damage to tool

components.

By using the Paslode Cordless Framing Nailer at its

recommended cycle rate, you will be able to drive several

thousand nails in a typical workday.

Fasteners: 30° paper tape collation

Minimum 2 inch x .113 dia. shank (50 x 2.87mm)

Maximum 3-1/4 inch x .131dia.shank (90 x 3.15mm)

Magazine Capacity: 1 nail strip + 5 fasteners.

Battery : 7.4 volts DC - Provides enough energy to

drive approximately 9000 fasteners on a full

charge.

Fuel Cell: Paslode Framing Fuel Cell. Liquid hydrocarbon-

Provides enough fuel to drive approximately

1200 fasteners.

Cover and Filter

Motor Housing

MOTOR ASSEMBLY

Adjustable

Work-Contacting

Element

Follower

Channel magazine

HANDLE ASSEMBLY

Battery

Compartment

(Opposite Side)

Battery

Indicator Light (LED)

Fuel Cartridge Compartment

Utility

Hook

Toe Nailing Teeth

NOTE: Altitude Restriction

Paslode Cordless tools are powered by an internal

combustion engine and are effected by altitude. The

tool may lose power or not cycle consistantly at

elevations of 6000 feet (1,828 meters) or greater.

Trigger

5

Safety Instructions

The following safety instructions have been included in this

booklet to provide you with basic information necessary for

safe operation of the Paslode Cordless Framing Nailer. DO

NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU

HAVE READ AND UNDERSTAND ALL SAFETY

PRECAUTIONS AND MANUAL INSTRUCTIONS.

In addition to these instructions, training may be necessary.

Contact your Paslode representative for additional

information.

WARNING

The Paslode Cordless

Framing Nailer is an

internal combustion

device. It produces hot

exhaust gases that may

ignite flammable

materials. Never use the

tool in a combustible

environment or in the

presence of combustible

materials, such as

flammable chemicals,

adhesives, gasoline, or

solvents.

WARNING

Never attempt to operate

this tool until you have

read and understood all

safety precautions and

manual instructions.

Failure to follow all safety

precautions instructions

may result in a permanent

loss of vision, serious per-

sonal or even fatal injury,

property damage and/or

tool damage.

WARNING

Never expose or store the

tool, fuel or battery at

temperatures in excess of

120°F (49°C). Fuel and/

or the battery may burst,

releasing flammable gas.

WARNING

Framing Nailer, fuel cart-

ridge, battery cell and bat-

tery charger out of the reach

of children.

WARNING

This tool must be operated

only in a well-ventilated

environment, because

the tool exhausts carbon

monoxide similar to a gas

chainsaw or lawnmower.

Exposure to carbon

monoxide from use in

eclosed areas, may cause

dizziness, nausea, or

unconsciousness or

death.

ALWAYS keep the Cordless

6

Safety Instructions

WARNING

EYE and EAR safety gear

must be worn when

working with or in the

vicinity of the Paslode

Cordless Framing Nailer.

7. NEVER OPERATE THE TOOL WITH THE WORK

CONTACTING ELEMENT REMOVED OR DISABLED.

This device helps reduce the possibility of accidental

fastener discharge by preventing the tool from operating

until it is completely against the work surface.

NEVER operate the tool if the work contacting element

is not working properly.

8. ALWAYS POINT THE TOOL AWAY FROM YOURSELF

AND OTHERS WHEN CLEARING JAMS OR

REMOVING FASTENERS. REMOVE THE FUEL

CARTRIDGE AND BATTERY.

Pull the follower slightly back and push the release

lever. Tip the tool nose up slightly and fasteners should

slide out of the rear of the magazine. If fasteners are

jammed, refer to the appropriate servicing section of

this manual.

9. NEVER OPERATE THE CORDLESS FRAMING

NAILER IF PARTS ARE LOOSE, DAMAGED OR

MISSING.

10. NEVER DRIVE FASTENERS INTO KNOTS OR ON

TOP OF OTHER FASTENERS.

A fastener may ricochet and cause serious injury.

11. OPERATE THE TOOL ONLY ON THE WORKPIECE.

1. Eye protection must meet the requirements of ANSI

Standard Z87.1 and should have side shields for

increased protection. As an employer you are

responsible for enforcing the use of eye protection

equipment by the tool operator and all personnel in the

work area.

2. NEVER ASSUME THE TOOL IS EMPTY.

Never point the tool at yourself or anyone else.

3. NEVER ENGAGE IN "HORSEPLAY" WITH THE TOOL.

The Cordless Framing Nailer is not a toy – it is a tool.

Careless and improper use may result in a serious

accident.

4. NEVER CARRY THE TOOL WITH YOUR FINGER ON,

OR SQUEEZING, THE TRIGGER.

This practice may result in the accidental discharge of

a fastener.

5. NEVER OPERATE A MALFUNCTIONING TOOL.

Refer to the servicing or troubleshooting section of this

manual to correct the problem. If the problem cannot be

corrected, stop using the tool and report it to your

supervisor or Paslode representative.

6. DO NOT LOAD FASTENERS WITH THE TRIGGER

AND/OR WORK CONTACTING ELEMENT PRESSED

IN. A fastener may be accidentally discharged.

WARNING

The Cordless Framimg

Nailer must be operated

only when it is in contact

with the work surface.

When fastening thin

materials such as

plywood, be sure to

position the tool so that

the fastener is driven into

the underlying piece.

12. NEVER DRIVE FASTENERS INTO AREAS WITH

CONCEALED HAZARDS.

Always check the area behind the work surface for

electrical wiring, gas pipes, water pipes, sewer drains or

other potential hazards.

7

14. ALLOW ONLY QUALIFIED PERSONNEL TO OPERATE

THE CORDLESS FRAMING NAILER.

WARNING

Only persons who have

read and fully understand

all tool operation, safety

and maintenance

instructions should be

allowed to operate the tool.

15. PROPERLY STORE FUEL CELL.

16. ALWAYS STORE THE TOOL WITH THE FUEL

CARTRIDGE AND BATTERY REMOVED.

Store the fuel cartridge in the case with the Cordless

Framing Nailer.

17. KEEP THE TOOL CLEAN AND WELL MAINTAINED.

A clean tool is less likely to jam or malfunction.

18. KEEP YOUR HANDS CLEAR OF THE WORK AREA

SURFACE.

WARNING

Always store tool, fuel

cartridge and battery

where they will not be

exposed to an open flame,

sparks or temperatures

above 120° F (49° C).

WARNING

A fastener may exit at an

angle unexpectedly and

cause injury.

IMPORTANT SAFETY INSTRUCTIONS!

SAVE THESE INSTRUCTIONS!

DANGER

TO REDUCE THE RISK OF FIRE

OR ELECTRIC SHOCK, CAREFULLY

FOLLOW THESE INSTRUCTIONS

CHARGING SYSTEM SAFETY

INSTRUCTIONS!

13. ALWAYS MAINTAIN SECURE AND UNOBSTRUCTED

FOOTING WHEN ON LADDERS, PLATFORMS OR

OTHER HIGH LOCATIONS.

WARNING

Never over-reach, since

tool recoil may cause a

loss of balance. Always

be aware of edges and

drop-offs when nailing on

rooftops and other high

locations. Keep them in

full view.

Safety Instructions

For connection to a supply outside North

America, use an attachment plug adapter

of the proper configuration for the power

outlet, if needed.

8

Battery And Charging System

Charging Instructions:

1.

2.

NOTE

3.

After charging, the red light will go out and the green

light will come on, indicating that the battery is fully

charged. The charger will keep the battery at full

charge until it is removed.

4.

Charging Times:

First charge (new battery) 1.5hours

Discharged Battery

5 minutes to 1.5 hours

Charging Don'ts:

1.

Never charge battery outdoors in moist or damp wet

conditions or in temperatures below 40ºF (5ºC).

2.

Never allow metal objects to come in contact with

battery terminals.

3. Never puncture or attempt to open battery case or

cells.

4.

Never store battery where it will be subjected to

temperatures above 120 F (49 C).

5. Never incinerate battery.

6.

Never use a defective battery charger, one that

overheats and/or smokes when plugged in.

7. Never immerse the battery or charger in water.

Battery disposal:

The Paslode batteries contain lithium and should be re-

cycled or disposed of properly.

You may contact your local recycling center for information

on where to return the spent battery or call 1-800-822-8837

for information on Li-ion battery recycling in your area.

WARNING

CHEMICAL/EXPLOSION

HAZARD

ReadALLinstructionsbefore

charging or using battery.

Failure to follow ALL

instructionsmayresultinfire,

severe burns, or release of

toxic materials.

Important Charging Notes:

The Paslode Cordless tool comes with a rechargeable

Lithium Ion (Li-ion) battery and its own charging system.

This charging system is the only one that will work with

Paslode Li-ion batteries. The first step in preparing a new

tool for operation is to fully charge the battery. New batter-

ies are shipped partially discharged and must be

charged prior to first use. Batteries will take 5 minutes to

1.5 hour (time will be dependant on the amount of discharge

within the battery) to recharge.

Remove the battery from tool or case and insert termi-

nals down into charger. The red light will come on

indicating that the battery is charging and the green light

will go out.

If battery is completely discharged the red light and

the green light may flash back and forth for up to 20

minutes. This safety feature slowly recharges the

battery until it is ready to accept the full charging

current. If the red and green lights continue to flash

after 20 minutes, replace the battery.

Unplug the charger from the 120V AC or 240V AC

outlet.

Remove the charger unit from the tool case and plug

it into a 120V AC outlet. Set the charger base on a

stable surface. A green light will come on to indicate

the power is on and the charger circuit is ready.

PASLODE 240V 50HZ BATTERY CHARGING SYSTEM

AC-DC Adapter

Charger Base

DC Plug

Battery

Plug Receptacle

6ft. Cord

Battery

Charger

TECHNICAL DATA

Impulse Adapter (AC-DC)

Australia/New Zealand

Impulse Charger Base

Battery

7.4 VDC, 2150mAh, Lithium-ion

tupnI

240V, 50HZ

12VDC

Output Polarity

12VDC, 1.8A

PASLODE 120V 60HZ BATTERY CHARGING SYSTEM

Charger Input

Battery

7.4 VDC, 2150mAh, Lithium-ion

120V AC, 60HZ

Output Polarity

12VDC, 1.8A

1B.

Remove the wall transformer from the tool case and

plug into a 240V AC outlet. Set the charger base on a

stable surface and insert the wall transformer unitʼs plus

into the plug receptacle on the base of the charger (see

diagram). A green light indicates power is on and charg-

ing system is ready.

Australia/New ZealandNorth America

North America

Australia/New Zealand

9

Battery and Charging System

Inserting Battery

1. Load the battery, contacts first, into the Cordless

Framing Nailer.

2. Push battery fully forward into its locked position.

3. To remove battery, push down on locking tab and slide

battery out.

Battery Indicator Light

The illustration is a close-up of the side of the Paslode

Cordless framer handle. On the side of the handle is a small

plastic lens. This is the battery indicator light.

When you insert a fully-charged battery into the tool, you will

see a blinking green light. If the light blinks red, recharge the

battery.

Battery

Indicator

Light

Battery Standby

The battery can be placed in the standby position if the

tool is not going to be used for a period of time.

To place the battery into the standby position, push down

on the locking tab and slide the battery back so that the

locking tab engages into the standby position in the handle.

NOTE:If battery is left in tool for an extended period of time

in the normal operating position, the battery will discharge

completely and will require recharging.

Locking Tab

Standby Position

Normal Operating Position

10

WARNING

EXPLOSION/FIRE

HAZARD

Read ALL safety instructions

before using

the fuel cell. Failure to fol-

low ALL instructions may

This may cause serious per-

sonal injuries or property

damage.

Keep the fuel cartridge

away from heat, sparks

and open flame. Do not

smoke when handling or

operating tool or fuel cart-

ridge.

Exposure to temperatures

above 120°F (49°C) may

the fuel cartridge to

burst, releasing

flammable

gas.

WARNING

Sunlight can raise the inside temperature of an

unventilated motor vehicle or storage container to

above 140°F (60°C).

Never puncture or attempt to open the fuel; it is

nonrefillable.

Never incinerate, reclaim or recycle the fuel.

Never smoke while installing or operating the fuel

cartridge or tool.

Never inhale the spray.

Keep out of the reach of children.

Store fuel cartridge(s) in well-ventilated areas only.

NOTE

1.

Never attempt to refill the cartridge! Replace

with fresh fuel cartridge, and dispose of spent

cartridge properly.

1.

2. When replacing fuel cartridge also clean or replace

air filter for optimum tool operation.

Paslode Framing Fuel Cell

The fuel contains a small amount of oil to keep the tool

lubricated during use. It is not necessary to oil the tool

during normal operation. When cleaning the tool, use only

Paslode Cordless tool oil. Using oils not formulated for the

Paslode Cordless Tool, may cause loss of power and may

damage the internal parts of the tool's motor.

NOTE: Altitude Restriction

Paslode Cordless tools are powered by an

internal

combustion engine and are effected by altitude. The

tool may lose power or not cycle consistantly at

elevations of 6000 feet or greater. For optimum perform-

ance use at 6000 feet or less.

DANGER

2. Do not attempt to install the fuel cartridge cap on

other fuel cells. This may result in damage to the

tool and injury to the user and by standers!

Paslode Framing Fuel Cell

innerThis container holds the fuel. The space

innerbetween the container and the outer cylinder is filled

with a gas, called the propellant, which is under pressure.

To eject the fuel, propellant pressure squeezes the inner

fuel container much as you squeeze a tube of toothpaste.

This squeezing action ensures that all the fuel is used,

and that the Cordless Nailer can operate in any position.

However, over time the propellant pressure diminishes

until it is no longer able to squeeze the inner fuel

container. This is why a nailer using a fuel cartridge

beyond the “Best Use Before” date may not work consis-

tently or at all.

cause

or handling

result in

explosion or fire.

Do not attempt to remove or reuse the

Paslode Framing Fuel Cell

.

There is a second container inside the Paslode Framing

Fuel Cell.

If you expose the empty or expired Paslode Framing Fuel

Cell to extreme temperatures, the propellant gas will expand

and could cause the container to burst, releasing flammable

gases.

11

NOTE:

For maximum performance use fuel before “Best Use Before” date.

Paslode Framing Fuel Cell Disposal Guidelines:

Paslode the industry leader in cordless technology provides this information to assist users with the proper disposal of discarded

fuel cells/cartridges. Acceptable disposal options vary depending on the type of fuel cell/cartridge users. All users must cons

ider

federal, state and local solid waste regulations to ensure that discarded fuel cells/cartridges are disposed of properly. Users

must

contact their local solid waste authority for further guidance.

Discarded fuel cells/cartridges (used or unused) may be considered hazardous waste under the Resource Conservation and

Recovery Act (RCRA) depending on several factors as described in the paragraphs that follow. Upon disposal used and unused

fuel cells/cartridges may be classified as ignitable hazardous waste (waste code D001) under U.S. EPA regulations.

Hazardous waste generated by homeowners and contractors who perform routine maintenance for homeowners in their homes are

not regulated by RCRA. In general, "household wastes" generated by homeowners and their contractors are exempt from hazard-

ous waste regulation because those wastes are expressly excluded from the definition of hazardous waste. For example US EPA

has excluded as "household waste" aerosol cans that contain residual product and propellent. Thus under

federal hazardous waste

regulations homeowners and contractors may dispose of discarded fuel cells/cartridges as general refuse in a properly permitted

municipal landfill. These users must still contact their local solid waste authority to determine if any state or local regulation

prohibits or restricts such disposal.

Paslode takes no responsibility for proper fuel cell/cartridge disposal. Proper disposal remains the responsibility of sellers and

users. All sellers and users must contact their local solid waste authority to determine if any

federal, state or local regulation

prohibits or restricts disposal. Users may obtain more information about U.S. EPA hazardous waste regulations at the following

internet address: www.epa.gov/epaoswee.osw/hazwaste.htm

Alternatively users may contact U.S. EPA's RCRA Superfund Call Center at 1-800-424-9346 to receive more information.

Australia Call Centre 1-800-727-5633

DANGER

Paslode Framing Fuel Cells are flammable.

Do not remove fuel cartridge cap or install on other

fuel cells!

“Best Use Before” Date

Note: Australia and

New Zealand Framing

Fuel Cells require a

clockwise twist of the

valve to lock the valve

into position.

Paslode Framing Fuel Cell Cap

Paslode Cordless fuel cartridges are marked with a best use before

date on the bottom of the can and on the Fuel Fastener Pack carton.

BEST USE BEFORE

14 FEB 1A

Paslode Framing Fuel Cell

12

Paslode Framing Fuel Cell

1. Swing Up

2. Push Down

Inserting Paslode

Framing Fuel Cell

A. To insert the Paslode

Framing Fuel Cell into the

Cordless Framing Nailer,

press up at the bottom of the

actuator cover and pivot

outward to open. The cover

will swing out of the way.

B. Lift the Paslode Framing

Fuel Cell adaptor and insert

the fuel cell into the tool.

C. Release the adaptor so it

is centered on the fuel cell.

D. Close the actuator cover

to complete the loading of

the fuel in the Cordless

Framing Nailer. Do this by

swinging it up and over the

Paslode Framing Fuel Cell,

and pushing down until the

actuator cover snaps into

position.

Fasteners

The Paslode Cordless Nailer drives Paslode RounDrive®

and D/Head nails, which have been collated into strips.

The use of nails that do not meet Paslode standards could

cause tool damage and void your warranty. Paslode nail

sizes and types are illustrated in the Fasteners and Appli-

cations section.

Loading Fasteners

A. Drop the nail strip into the

empty magazine.

B. Pull the follower up past

the last nail.

C. Tool is ready to shoot.

wear safety glasses

RounDrive Nails

1. Press Up

2. Pull Out

wear safety glasses

RounDrive Nails

wear safety glasses

RounDrive Nails

13

Preparing the Paslode Cordless Framing Nailer for Use

Paslode Cordless Framing Nailer and

Outdoor Weather

Use the Cordless Framing Nailer outdoors, in clear weather,

when the nailer, fuel cartridge, and battery are between

14°F (-10°C) and 120°F (49°C.

HOT WEATHER OPERATION

The Cordless Framing Nailer requires cooling of the motor

assembly to operate properly. The fan normally provides

the necessary air flow to permit continuous operation.

Whenever the Cordless Framing Nailer is idle for extended

periods, keep the Paslode Framing Fuel Cell and tool out of

direct sunlight and in surroundings where temperatures

will not exceed 120°F(49°C). After extended periods of

continuous use, it may be necessary to cool the motor by

setting tool aside for 10-15 minutes or until the tool

operates normally. An overheated tool may not drive nails

completely or may operate erratically.

COLD WEATHER OPERATION

Fuel at cold temperatures lose the required propellant force.

Bring the tool, battery, and fuel cartridge above minimum

operating temperature without direct exposure to flame, and

check the battery.

CAUTION

The Cordless Framing Nailer should not be used in the

rain or where excessive moisture is present. The use

of the Paslode Cordless Technology under these

conditions may result in damage to tool components

and cause tool to malfunction.

The purpose of this feature is to prevent needless

blank cycling,which could waste fuel and damage

tool components. Five (5) nails will be left in the

magazine when the follower reaches the lockout

area. The indicator arrow shows that you can reload.

It does not indicate that the Cordless Framing Nailer

is empty. Because of a lockout feature in the

Cordless Framing Nailer it will not operate when the

nail supply in the tool is less than six (6) nails.

Lockout Feature

Unloading Fasteners

A. Pull the follower back to

the end (square pocket

area).

B. Press the button and the

follower will lock in place.

C. Flip the tool and nail strip

will drop out.

D. Pull the follower to the

very end of the guide, so the

button will pop out and the

follower will release from

that position.

wear safety glasses

RounDrive Nails

wear safety glasses

wear safety glasses wear safety glasses

RounDrive Nails

14

Paslode Cordless Framing Nailer Operation

No-Mar Work-Contacting Element

For applications where the work-piece must be mark free,

like in siding and recreational decks, order the No-Mar

Work-Contacting Element, Part No. 901252

ANZ Product Code: B20544G

DANGER

Never attempt to operate the Cordless Framing Nailer

unless both adjustment screws are installed. Intentional

removal of an adjustment screw could result in improper

tool operation, loss of nail control and injury to tool user

or bystanders.

PRESS WORK CONTACT

ELEMENT AGAINST THE

WORK SURFACE

Fan motor starts,

fuel is injected into

combustion chamber

and mixed with air by

the fan.

SQUEEZE

TRIGGER

Spark plug sparks and

fuel/air mixture ignites.

Combustion powers

piston assembly driving

fastener.

LIFT TOOL -

RELEASE

TRIGGER

Combustion chamber

opens.

Fan exhausts

hot gases and cools

internal components.

Standard

Work-Contacting

Element

DANGER

The work contacting element and nose will become hot

after prolonged or rapid use. If it becomes necessary to

adjust the work contacting element, avoid touching with

bare hands.

Adjustable Utility Hook

To set depth of drive

The adjustable utility hook can be used as a belt or

rafter hook. To adjust the utility hook, push the black

button in the direction of the arrow and rotate it to the

desired position.

Probe Stop

Note: The fan will run for approximately 10 seconds after the last nail

is driven. After rapid firing (at least 32 times in 80 seconds), the fan will

run for 60 seconds to cool the tool.

Move up to Increase

Drive Depth

Move Down to Reduce

Drive Depth

Push

Depth of Drive Adjustment

Remove the battery before adjusting the depth of drive.

If the tool is over-driving (the nail head is driven below the

surface of the wood), the work contacting element should be

moved down slightly. If the nails stand up (the head is not

flush with the work surface), the work contacting element

should be moved up slightly. The indicator marks are set at

1/10" (2.5mm) increments with a total range of 1/2" (13mm).

Adjust the work contacting element to get the nail head

depth to meet job requirements.

The depth of drive adjustment is made by adjusting the

work contacting element. Squeezing the probe stop

release buttons toward each other will allow the work

contacting element to be moved up or down.

15

Fasteners and Applications

NOITACILPPAEPYTEZIS

,gnihtaehs llaw ,tnemyalrednUknahS gniR nommoC) (50 x 2.87 mm)D6( 311. x "2

roof and floor decking, siding

gnidis ,gnicneF,knahs gnir nommoC) (50 x 2.87 mm)D6( 311. x "2

HD Galv, GalvGuard™

,tnemyalrednu ,gnikced roolf & fooRknahs gnir relooC) (60 x 2.87 mm)D8( 311. x "8/3-2

sheathing

gnicnef ,gnidis ,gnikced lanoitaerceR,knahs gnir detaoC) (70 x 2.87 mm))D8( 311. x "4/3-2

gniledomeRlian detaoC) (76 x 3.05 mm)D01( 021. x "3

,gnidis ,gnikced lanoitaercer ,gnicneF k,nahs gniR) (76 x 3.05 mm)D01( 021. x "3

sfoor elit

gnimarFlian detaoC) (75 x 3.33 mm)D01( 131. x "3

3-1/2" x .131 (90 x 3.33 mm)

gnimarF

Framing / Fencing

Landscaping

lian detaoC

Bright

HD Galv

) (82 x 3.33 mm)D21( 131. x "4/1-3

Smooth Shank - For general construction, carpentry and

framing: the most popular and versatile.

Ring Shank - The ring shank provides improved withdrawal

resistance for applications where the resistance from smooth

shank fasteners is not adequate: floor decking, crating,

pallets.

Hardened

Note: For Australia and New Zealand, nail sizes, coating types and applications

may vary. Please check your local building code regulations.

Steel - For attaching wooden plates to green

concrete foundations; 2X furring strips to cinder block.

GalvGuard™- These nails are hot dipped galvanized with

a baked on polymer coating. They offer the highest cor-

rosion resistance of any galvanized nail. These nails

should be used where higher corrosion resistance is required

to retard rust and rust staining. Recommended for use in

natural wood siding, such as cedar, redwood, cypress and

preservative treated lumber. (Not for use in all-weather

wood foundations.)

The Paslode Cordless Framing Nailer is not recommended for use with 3" (75mm)

and longer Ring Shank nails in pressure treated lumber

.

16

PASLODE FRAMING FUEL CELL CHECK

DANGER

Wear safety glasses when performing this test. Never

perform this test near an open flame or sparks, while

smoking, or where the fuel may get into your eyes.

Restrict Field Service to the Following

CHECKING THE ENERGY LEVEL OF THE BATTERY

RECHARGING THE BATTERY

CHECKING THE PASLODE FRAMING FUEL CELL

REPLACING THE PASLODE FRAMING FUEL CELL

CLEANING THE AIR FILTER

CLEARING A JAM

Attempts to go beyond these procedures could result in

serious personal injury or damage to the Cordless Framing

Nailer and voiding the warranty.

There are certain problems you may encounter when you

are using the Cordless Framing Nailer that you will be able

to correct on the work site. The following field service

procedures are the only service procedures you should

attempt. Anything else that may appear wrong with the

Cordless Framing Nailer should only be diagnosed and

repaired by a fully trained service technician. If you have any

reason to believe that your problem is beyond the service

procedures in this manual, contact your Paslode

representative immediately.

Clearing a Jam

An occasional problem you may encounter is a jammed

fastener. Because of the unique design of the Cordless

Framing Nailer, clearing a jammed fastener is easy:

1. Remove the Paslode Framing Fuel Cell and battery.

2. Lock follower back in magazine and remove fasteners.

3. Loosen the (2) magazine mounting screws with the

5/32 hex key.

4. Pull handle/magazine away from the nose of the tool

and clear jam.

5. Realign handle magazine to nose, and tighten mounting

screws.

6. Reload fasteners and release follower.

Battery Check

Periodically

For US Region Only

If you need further assistance, please visit:

paslode.com/service-retail-locator

to find your closest service center.

check the battery indicator light in the handle

of the Cordless Framing Nailer. When encountering a

problem, the first step should always be to make sure the

battery has enough energy to operate the tool.

When the work contacting element is pressed on work

piece, the fan motor will turn on and blinking green light will

turn solid green. If the light blinks red or glows red, recharge

battery.

DANGER

Never attempt any maintenance of the Paslode Cordless

Framing Nailer without first removing the fuel cartridge

and battery. Maintenance should be started only after

the tool is completely inoperative.

Servicing

Remove

If the nailerʼs fan operates and the light is green but the tool

will not cycle consistently or at all, check the fuel cell.

First remove the fuel cell from the tool and check the

“Best Use Before” date stamped on the bottom. If it is

beyond this date, the fuel cell may not consistently

dispense the proper amount of fuel – even if the fuel cell

has never been used. To test if the fuel cell still dispenses

fuel:

1. Hold the fuel cell in the upright position with the flat

bottom toward the ground – this orientation is important

for a proper test.

2. Gently push the tip of the fuel cell cap against a solid

object five times.

3. A small amount of fuel should be released all five times.

4. If fuel is not released every time it indicates the fuel cell

is empty or expired* and must be replaced.

* Expired fuel cell may dispense fuel when upside down

or sideways but will not work more than a couple of times in

the upright position because of the reduced internal pres-

sure (see page 10 for more information).

17

Servicing

Air Filter

Open the grille by pressing slightly above the adapter, and

pivoting the cover open. The air filter simply lifts out.

Tap the filter GENTLY to remove any dust. Check and clean

the air filter every two days. Soap and water restores the

filter to a "like new" condition.

End-of-Workday Routine

At the end of each workday, conduct an end-of-workday

routine. These simple steps are based on maintaining the

safety and operational efficiency of the Paslode Cordless

Framing Nailer.

Before you leave the work site:

1. Remove battery and store in tool case. Always use the

Cordless Framing Nailer case for transporting and

storing the tool.

2. Dispose of all empty fuel cells. Remember to

dispose of these cartridges where they will not be found

by children, crushed, punctured, or burned.

When you get home:

1. Place the battery in its charger if it needs charging as

indicated by the red charge light on the handle.

2. Wipe your Cordless Framing Nailer with a clean, soft

cloth.

3. Remove and clean the filter every two days.

Cordless Framing Nailer Paslode

Cordless Tool Accessories

A variety of accessories are available for the Paslode

Cordless Framing Nailer:

No-Mar Work Contacting Element

USA Part No. 901252

Au and NZ Part No. B20544G

Battery

USA Part No. 902654

Au and NZ Part No. B20543A

Clear Safety Glasses

USA Part No. 401382

Paslode Lubricating Oil

USA Part No. 401482

Au and NZ Part No. B20544F

Battery Charger

USA Part No. 902667

Au and NZ Part No. B20543B

Paslode Cordless Framing Nailer Case

USA Part No. 905607

Contact your Paslode®representative for additional

information.

Tools

A 5/32 Hex Socket Wrench (Part No. 401331) is provided

with each Paslode Cordless framer.

WARNING

Make certain magazine mounting screws are tight and

magazine is tight to nose. Attempting to fire tool with a

loose magazine will result in loss of nail control,

damage to tool, or nail discharge toward operator.

Tool Cleaning and Oiling

Periodic cleaning and oiling are necessary to keep the

Paslode Cordless Nailer operating properly. The tool

should be cleaned and lubricated at least every 50,000

cycles. This number may vary depending upon the rate at

which the tool is used and the operating conditions it is

used in. The chart in the cleaning instructions will help you

determine how often the tool should be cleaned.

Grille

Filter

18

Battery does not appear to accept charge

when the battery and charger are plugged

into the wall mount adapter.

Battery charger flashes red/green for more

than 20 minutes.

Charger gets hot, makes excessively loud

noise, or smokes during charging cycle.

Charger cord or wall plug gets hot.

Inoperative indicator lights on charger, or

defective charger.

Defective battery.

Battery damaged or cycle life exhausted.

Damaged charger.

Preparing Tool for Operation - Battery/Charger Problems

ECIVRESSMELBORP ELBISSOPMOTPMYS

Normal Stage of Operation

Fan does not run - tool indicator light is

blinking red or solid red.

Fan does not run, or runs slower than

normal - tool indicator light is solid red.

Battery is not charged.

Battery terminals are oily, dirty, or corroded.

Battery is discharged.

Charge battery.

Clean battery terminals with cloth or pencil

eraser.

Charge battery.

ECIVRESSMELBORP ELBISSOPMOTPMYS

Work-contacting element does not depress

fully - tool does not operate.

Tool will not cycle - fan runs, indicator light

is solid green.

Lockout bracket is stuck in lockout position.

Work-contacting element is bent, worn or at

the deepest setting.

Follower is not behind fasteners.

Spark plug is dirty.

No spark is generated.

Check lockout.

If the lockout is stuck or not working properly,

stop using the tool and return to an authorized

Paslode dealer for service.

Remove and inspect lower probe. Clean,

adjust or replace lower probe as required.

Position follower behind fasteners.

Replace Paslode Framing Fuel Cell. See page

16 for details on how to check fuel cells.

Clean tool cylinder head and spark plug.

Return tool to authorized Paslode

®

dealer for

service.

Try battery in tool after a full charge cycle. If

tool LED is green, charger is not working

properly. Replace charger, or monitor

charging time to ensure battery has

adequate time for recharging. It is normal

for battery to feel warm after properly

charging.

Replace battery.

Discontinue use immediately and unplug

from power source. Replace charger and

tag or dispose of charger to prevent

accidental reuse or connection to power

source.

Troubleshooting

.slian fo pirts daoL.loot ni slian ssel ro )4( ruoF

Paslode Framing Fuel Cell empty or past the

“Best Use Before” date stamped on the bottom

of the fuel cell.

If tool will not operate after following the above service directions, return the tool to an authorized Paslode®

representative for service.

19

Tool operates properly, but fasteners do not

drive fully.

Tool operates, but no fastener is driven.

Tool operates erratically or appears to be

losing power - tool indicator light is green.

Work-contacting element requires adjustment.

Dirty air filter.

There may be loss of seal in combustion

chamber.

Wrong fasteners being used.

Tool requires cleaning.

Follower not properly engaged behind fastener

strip.

Jammed fastener.

Spark plug wire is loose.

Filter element is dirty, causing tool to overheat.

Adjust work contacting element.

Clean filter.

Press work contacting element against

workpiece for 20 seconds. Pull trigger. If

fastener does not drive, there is a leak that

requires service.

Use only fasteners meeting Paslode®

specifications. Check Fasteners and

Applications section for fastener types and

sizes recommended for use in Cordless tool.

Clean per instructions.

Position follower behind fastener strip and

engage strip.

Clear jam.

Check spark plug wire.

Remove filter element and clean. Use soap

and water to remove stubborn debris.

Normal Stage of Operation

ECIVRESSMELBORPELBISSOPMOTPMYS

Tool operated and drove fasteners, but

driver blade did not return to up position.

Combustion chamber does not drop after

tool cycles.

Built-up dirt and debris on driver blade or in

nose bore.

Mid check is dirty or disabled.

Work-contacting element is bent or is dirty.

Clean driver blade and nose bore with

degreaser cleaner.

Return tool to authorized Paslode® Cordless

dealer for service.

Clean or replace work-contacting element.

Troubleshooting

For US Region Only

If you need further assistance, please visit:

paslode.com/service-retail-locator

to find your closest service center.

For technical support contact Paslode:

Australia: 1-800-PASLODE (727-5633)

www. paslode.com.au

New Zealand: 09-477-3000

www.paslode.co.nz

20

Canada

A Division of ITW Australia Pty Ltd

ABN 63 004 235 063

PO Box 914

45 to 47 Williamson Road

Ingleburn,1890

www.paslode.com.au

Australia

A Division of ITW New Zealand Ltd

PO Box 100 303 NSMC

8 Orbit Drive

Aukland, New Zealand

www.paslode.co.nz

New Zealand

USA

An Illinois Tool Works Co.

155 Harlem Avenue

Glenview, IL 60025

www.paslode.com

120 Travail Road

Markham,Ontario

L3S 3J1

800-387-6472

www.paslode.ca

For Cleaning Procedure Manual

Please visit: Paslode.com/products/tools/cordless-xp-Framing-Nailer

La page charge ...

Paslode CFN325XP Manuel utilisateur

Paslode CFN325XP Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents