red lion DA High Speed Rate Counter Module Manuel utilisateur

Marque: red lion

Modèle: DA High Speed Rate Counter Module

Taper: Manuel utilisateur

Installation HSRC - A

Drawing No. LP1148

Effective 09/2022

DA High Speed Rate Counter Module

Installation Guide

FOR USE IN HAZARDOUS LOCATIONS:

Class I, Division 2, Groups A, B, C, and D

LISTED

IND.CONT. EQ.

E317425

MODULE PACKAGE CHECKLIST

This product package should contain the items listed below. If

any items are missing or damaged, contact Red Lion immediately.

- DIN Rail Mount DA HSRC Module

- Installation Guide

GENERAL DESCRIPTION

The DA HSRC module features three counters designed for use

with the DA70 controllers. This module is an ideal choice to

monitor quadrature/direction encoders, count events, measure

pulse width, and measure rates.

The digital inputs accept standard DC inputs or contact

closures. Each counter has a software selectable input filter that

can be used to prevent contact bounce. 4 SSR outputs can

indicate the status of a count total or rate measurement.

Counting modes include quadrature/direction encoders, count

events on one input, sum events on two inputs, count with

direction, count SSR output activations, etc.

The SSR outputs are capable of switching up to one amp DC

each. For applications requiring large loads to be controlled or AC

voltages, several DIN rail mount interposing relays are available.

The modules connect and communicate via proprietary

backplane to the DA host device. The DA host device, equipped

with serial ports as well as an Ethernet port(s), allows the system

to share data with PCs, PLCs, and SCADA systems.

Internal power management circuits allow the module to be

replaced while power is applied, which reduces downtime in the

event of a module failure. All configuration information is stored

locally within the module, as well as in the Host, so replacement

modules do not need to be configured.

CONFIGURATION

The DA HSRC modules are configured with Windows®

compatible Crimson® software. The software is an easy to use,

graphical interface which provides a means of configuration and

commissioning of new systems, as well as routine module

re-calibration.

SAFETY SUMMARY

All safety related regulations, local codes and instructions that

appear in this document or on equipment must be observed to

ensure personal safety and to prevent damage to either the

device or equipment connected to it.

Do not use these products to replace proper safety interlocking.

No software-based device (or any other solid-state device) should

ever be designed to be responsible for the maintenance of

personnel safety or consequential equipment not equipped with

safeguards. Red Lion disclaims any responsibility for damages,

either direct or consequential, that result from the use of this

equipment in a manner not specified.

CAUTION: Risk of Danger

Read complete instructions prior to installation and

operation of the unit.

ATTENTION : Risque de danger

Lire les instructions complètes avant l’installation et

l’utilisation de l’appareil.

WARNING - EXPLOSION HAZARD - SUBSTITUTION

OF COMPONENTS MAY IMPAIR SUITABILITY FOR

CLASS I, DIVISION 2

AVERTISSEMENT - DANGER D’EXPLOSION - LE

REMPLACEMENT DE COMPOSANTS PEUT NUIRE À

L’APTITUDE À LA CLASSE I, DIVISION 2

zAdds three counters to the DA70 products

zFour count inputs, four user inputs, four setpoint outputs, and

four digital outputs

zOffers complete isolation; inputs, outputs, power, and

communication

zDual channel counter inputs configurable for count, rate, or

quadrature counting modes

zOutputs are sinking with max of 1 A per channel

0.49

[12.51]

0.45 [11.50]

4.53 [114.97]

6.22

[157.91]

1.91

[48.51]

1.35

[34.32]

6.00

[152.40]

DIMENSIONS In inches [mm]

II 3 G Ex ec IIC T4 Gc

DEMKO 20 ATEX 2268X

IECEx UL 20.0007X

UL22UKEX2576X

Drawing No. LP1148 Effective 09 2022

SPECIFICATIONS

1. POWER REQUIREMENTS:

Power is supplied by the DA host controller. Modules may be

hot-swapped (replaced while powered up) in non-hazardous

locations only.

Max Power: 2.0 W

2. LEDs: One LED indicator for each I/O point and a status LED.

3. MEMORY: Non-volatile memory retains all programmable

parameters. The Controller also stores the parameters in order

to reprogram any modules that need updates.

4. COUNTER INPUTS:

2 dual channel inputs, individual screw terminals for channel-

to-channel isolation and independent Sink/Source hardware

configuration

Maximum input voltage: 30 VDC, reverse polarity protected

Guaranteed ON voltage: 2.5 V

Guaranteed OFF voltage: 1.5 V

TTL compatible

Current draw: 10.5 mA @ 30 VDC, 4.5 mA @ 2.5 VDC,

nominal spec: 8 mA

Range: -2,147,483,648 to 2,147,483,647

Maximum Count Rates:

MODE COUNTER A COUNTER B

Count X1 500 KHz 500 KHz

Count X1 with Direction 50 KHz 50 KHz

Dual Input X1 Add/Add 50 KHz 50 KHz

Dual Input X1 Add/Subtract 50 KHz 50 KHz

Quad X1 50 KHz 50 KHz

Quad X2 500 KHz 50 KHz

Quad X4 500 KHz 500 KHz

Count X2 500 KHz 500 KHz

Count X2 with Direction 50 KHz 50 KHz

Pulse Width Fall/Fall Accuracy:

± 2.0 msec

Accuracy:

± 2.0 msec

Pulse Width Fall/Rise Accuracy:

± 2.0 msec

Accuracy:

± 2.0 msec

Pulse Width Rise/Fall Accuracy:

± 2.0 msec

Accuracy:

± 2.0 msec

Pulse Width Rise/Rise Accuracy:

± 2.0 msec

Accuracy:

± 2.0 msec

Software debounce filtering modes: None or Debounce.

Debounce limits input frequency to 50 Hz and input pulse

widths to 10 msec min.

Input isolation: 500 Vrms

5. RATE INPUTS:

Range: 0 to 999,999

Maximum Frequency: 500 KHz

Minimum Frequency: 0.001 Hz

Display Update Time: 0.1 to 999.9 seconds

Accuracy: ±0.01%

6. DIGITAL OUTPUT:

8 solid state N-channel open drain MOSFETs

Load Type: General purpose, resistive and Pilot Duty

All outputs share the same common

Rating: 1 ADC max

VDS ON: < 0.2 V @ 1 A

VDS MAX: 30 VDC

Offstate leakage current: 0.5 μA max

7. SIGNAL INPUTS (INPUT A and INPUT B):

Selectable inputs accept pulses from a variety of sources

including switch contacts, TTL outputs, and standard RLC

sensors. Inputs accept current sinking or current sourcing

outputs and provide software selectable input filtering for

low frequency signals or switch contact debounce.

8. USER INPUTS: Four programmable user inputs

Max. Continuous Input: 30 VDC

Channel-to-channel isolation

Response Time: 12 msec. max.

Independent Sink/Source hardware configuration

Guaranteed ON voltage: 2.5 V

Guaranteed OFF voltage: 1.5 V

TTL compatible

Current draw: 10.5 mA @ 30 VDC, 4.5 mA @ 2.5 VDC,

nominal spec: 8 mA

9. COMMUNICATIONS: Provided by the DA70 Controller

10. ENVIRONMENTAL CONDITIONS:

Operating Temperature Range: -40 to 75 °C TAMB

Storage Temperature Range: -40 to 80 °C TAMB

Operating and Storage Humidity: 0 to 95% max. RH non-

condensing

Vibration to IEC 60068-2-6: Operational 5-500 Hz, 2 g

Shock to IEC 60068-2-27: Operational 15 g

Altitude: Up to 2000 meters

Installation Category II, Pollution Degree 2 as defined in IEC/

EN 60664-1.

11. CERTIFICATIONS AND COMPLIANCES:

CE Approved

EN 61326-1 Immunity to Industrial Locations

Emission CISPR 11 Class A

IEC/EN 61010-1

RoHS Compliant

ATEX Approved

II 3 G Ex ec IIC T4 Gc

DEMKO 20 ATEX 2268X

IECEx Approved

IECEx UL 20.0007X

UKEX Approved

UL22UKEX2576X

UL Hazardous: File # E317425

Rugged IP30 enclosure

12. CONNECTIONS: Removable wire clamp screw terminal blocks

Wire Strip Length: 0.3" (7.5 mm)

Wire Gauge Capacity: 14 to 24 AWG (2.08 to 0.20 mm2)

copper wire only

Torque: 2 inch-lbs (0.23 N-m)

13. CONSTRUCTION: Plastic enclosure with IP30 rating. For

use only in an approved enclosure.

14. MOUNTING REQUIREMENTS: Mounts onto standard DIN

style top hat (T) profile mounting rails according to EN50022

– 35 x 7.5 mm and 35 x 15 mm.

15. WEIGHT: 10.2 oz (317.25 g)

This equipment is suitable for use in Class I, Division 2,

Groups A, B, C, D, or non-hazardous locations only.

Cet équipement est adapté à une utilisation dans des

endroits de classe I, Division 2, Groupes A, B, C, D, ou

dans des endroits non dangereux seulement.

WARNING - EXPLOSION HAZARD. NOT HOT

SWAPPABLE. DO NOT REMOVE OR REPLACE WHILE

CIRCUIT IS LIVE UNLESS THE AREA IS FREE OF

IGNITIBLE CONCENTRATIONS.

AVERTISSEMENT - RISQUE D’EXPLOSION. NON

ÉCHANGEABLE À CHAUD. NE PAS RETIRER OU

REMPLACER SOUS TENSION SAUF SI LA ZONE EST

EXEMPTE DE CONCENTRATIONS INFLAMMABLES.

Effective 09 2022 Drawing No. LP1148

HARDWARE INSTALLATION

Removing Module From Cradle

To remove the module from the cradle, push in the module

release button at the top of the cradle and pull the module out of

the cradle.

MODULE

CRADLE

Attaching the Module/Cradle to the DIN Rail

The DIN rail should be mounted

horizontally so that the unit’s

ventilation holes are vertical in

relation to installation orientation.

A minimum clearance of 1 inch

(25.4 mm) should be maintained

above and below the unit to

ensure proper thermal regulation.

The cradle can be installed on

the DIN rail with or without the

module attached. Ensure the DIN

rail lock latch is in the outward

most position (unlocked). Hook

the top back of the cradle DIN

rail clip over the DIN rail. Press

the cradle until flush with the rail and push the DIN rail lock latch

to the latched (in) position.

For hazardous location installation, the following shall be taken

into consideration:

— The equipment shall only be used in an area of at least

pollution degree 2, as defined in EN/IEC 60664-1.

— The equipment shall be installed in an enclosure that provides

a minimum ingress protection of IP54 in accordance with EN/

IEC 60079-0. The enclosure shall be accessible only with the

use of a tool.

— Transient protection shall be provided that is set at a level not

exceeding 140% of the peak rated voltage value at the supply

terminals to the equipment.

Installing Module into Cradle

Push module into cradle until you hear an audible click

indicating it is properly latched.

MODULE CRADLE

DIN

rail

MODULE HOT SWAPPING

If the area is known to be non-hazardous (free of ignitable

concentrations), then a module can be removed and/or installed

into a cradle attached to the controller while power is applied.

However, it is NOT recommended to connect to or remove from

the controller, a module/cradle pair or group of modules/cradles,

while power is applied. The power should be turned off anytime

a cradle or group of cradles (with or without modules) is plugged

into or removed from the controller.

DIN RAIL LOCK LATCH

Unlock Lock

COUNT / RATE INPUT OPERATION

Reference the Crimson 3.2 Software Guide for more details.

MODE COUNTER X INPUT A COUNTER X INPUT B

Count X1 Adds Input A falling edge. Not Used.

Count X1 with Direction Adds Input A falling edge if Input B is high. Subtracts if Input B is low.

Dual Input X1 Add/Add Adds Input A falling edge. Adds Input B falling edge.

Dual Input X1 Add/Subtract Adds Input A falling edge. Subtracts Input B falling edge.

Quad X1 Adds Input A rising edge when Input B is high. Subtracts on reverse rotation.

Quad X2 Adds Input A rising edge when Input B is high and Input

A falling edge when Input B is low.

Subtracts on reverse rotation.

Quad X4 Adds Input A falling edge when Input B is high, Input A

rising edge when Input B is low, Input B rising edge

when Input A is high, and Input B falling edge when

Input A is low.

Subtracts on reverse rotation.

Count X2 Adds Input A rising and falling edges. Not Used.

Count X2 with Direction Adds Input A rising and falling edges if Input B is high. Subtracts if Input B is low.

Pulse Width Fall to Fall Measures the time between an Input A falling edge and

the next Input A falling edge.

Not Used.

Pulse Width Fall to Rise Measures the time between an Input A falling edge and

the next Input A rising edge.

Not Used.

Pulse Width Rise to Fall Measures the time between an Input A rising edge and

the next Input A falling edge.

Not Used.

Pulse Width Rise to Rise Measures the time between an Input A rising edge and

the next Input A rising edge.

Not Used.

Drawing No. LP1148 Effective 09 2022

WIRING

All power, input and output (I/O) wiring must be in accordance

with Class I, Division 2 wiring methods and in accordance with

the authority having jurisdiction.

All conductors should meet voltage and current ratings for each

terminal. When wiring the module, use the numbers on the label

to identify the position number with the proper function. Strip

the wire, leaving approximately 0.3" (7.5 mm) of bare wire

exposed. Insert the wire into the terminal, and tighten.

I/O WIRING

The DA HSRC module offers 4 discrete count inputs, 4 discrete

user inputs, 4 discrete setpoint outputs, and 4 discrete digital

outputs. The discrete inputs and outputs operate on the same

voltage that powers the unit. Pluggable screw block terminals are

provided for the I/O wiring connections. Refer to the diagrams

below on how to make your I/O connections.

INPUT SIGNAL WIRING

Current Sourcing Output; Current Sinking Output

Switch; TTL Output

Rate; Quad/Direction

Dual Quad

USER INPUT WIRING

User Input terminals do not need to be wired in order to remain

in an inactive state

CAUTION: Only UL listed wiring with temperature

ratings greater than 90 °C permitted for Class I, Division

2, Zone 2 and ATEX, IECex and UKEX installations.

ATTENTION: Seul le câblage homologué UL avec des

températures nominales supérieures à 90°C est autorisé

pour les installations de classe I, Division 2 , zone 2 et

ATEX, IECex and UKEX.

Terminals

17 to 24

Terminals

25 to 32

Terminals

9 to 16

Terminals

1 to 8

DI3+

DI2+

DI3-

DI1-

DI1+

DI2-

DI4-

DI4+

DI8+

DI8-

DI7-

DI5+

DI6-

DI7+

DI6+

DI5-

DO4+

COM 3

DO1+

COM 2

DO3+

DO2+

COM 1

COM 4

COM 8

COM 5

DO6+

DO7+

COM 6

DO5+

COM 7

DO8+

DIGITAL OUTPUT 8

DIGITAL OUTPUT 6

DIGITAL OUTPUT 7

DIGITAL OUTPUT 5

SETPOINT 3

SETPOINT 2

SETPOINT 1

USER 4

USER 3

USER 2

USER 1

COUNTER B INPUT B

COUNTER B INPUT A

COUNTER A INPUT B

COUNTER A INPUT A

SETPOINT 4

OUTPUTINPUT

DI3+

DI2+

DI3-

DI1-

DI1+

DI2-

DI4-

DI4+

COUNTER B INPUT B

COUNTER B INPUT A

COUNTER A INPUT B

COUNTER A INPUT A

INPUT

PNP O.C.

NPN O.C.

DI3+

DI2+

DI3-

DI1-

DI1+

DI2-

DI4-

DI4+

COUNTER B INPUT B

COUNTER B INPUT A

COUNTER A INPUT B

COUNTER A INPUT A

INPUT

+5V

COMM

DI3+

DI2+

DI3-

DI1-

DI1+

DI2-

DI4-

DI4+

COUNTER B INPUT B

COUNTER B INPUT A

COUNTER A INPUT B

COUNTER A INPUT A

INPUT

DATA

COMMON

Rate

+8-28 VDC

DATA B

COMMON

+8-28 VDC

DATA A

Count

DI3+

DI2+

DI3-

DI1-

DI1+

DI2-

DI4-

DI4+

COUNTER B INPUT B

COUNTER B INPUT A

COUNTER A INPUT B

COUNTER A INPUT A

INPUT

DATA B

COMMON

+8-28 VDC

DATA A

Count

DATA B

COMMON

+8-28 VDC

DATA A

Count

DI8+

DI8-

DI7-

DI5+

DI6-

DI7+

DI6+

DI5-

USER 4

USER 3

USER 2

USER 1

INPUT

Effective 09 2022 Drawing No. LP1148

SETPOINT/DIGITAL OUTPUT WIRING

STATUS LED

LED

COLOR(S) LED STATE MEANING

Blue 3 quick flashes Module is booting.

Green Solid Module is configured and running.

Green/Off Flashing Module is running but is not

configured.

Green/

Purple

Flashing Module is performing calibration.

Red/Green Flashing Module is running but

communication with the controller

is inactive. If status persists, contact

technical support.

Red/Off Flashing An internal error has occurred. If

status persists, contact technical

support.

Yellow/Off Flashing Module position is unassigned. If

status persists, contact technical

support.

Off Solid Module application is not running or

the module is not powered. If status

persists, contact technical support.

RED LION CONTROLS TECHNICAL SUPPORT

If for any reason you have trouble operating, connecting, or

simply have questions concerning your new product, contact Red

Lion’s technical support.

Support: support.redlion.net

Website: www.redlion.net

Inside US: +1 (877) 432-9908

Outside US: +1 (717) 767-6511

Red Lion Controls, Inc.

35 Willow Springs Circle York, PA 17406

and the Red Lion logo are trademarks of Red Lion Controls,

Inc. All other company and product names are trademarks of

their respective owners.

ORDERING INFORMATION

DESCRIPTION PART NUMBER

DA Series I/O Module High-Speed Rate Counter DAM00I02C0000000

Load

DO4+

COM 3

DO1+

COM 2

DO3+

DO2+

COM 1

COM 4

COM 5

COM 6

DO5+

DIGITAL OUTPUT 6

DIGITAL OUTPUT 5

SETPOINT 3

SETPOINT 2

SETPOINT 1

SETPOINT 4

OUTPUT

Load

Drawing No. LP1148 Effective 09 2022

This page intentionally left blank.

Effective 09 2022 Drawing No. LP1148

This page intentionally left blank.

Drawing No. LP1148 Effective 09 2022

LIMITED WARRANTY

(a) Red Lion Controls Inc. (the “Company”) warrants that all Products shall be free from defects in material and

workmanship under normal use for the period of me provided in “Statement of Warranty Periods” (available at

www.redlion.net) current at the me of shipment of the Products (the “Warranty Period”). EXCEPT FOR THE

ABOVE-STATED WARRANTY, COMPANY MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE

PRODUCTS, INCLUDING ANY (A) WARRANTY OF MERCHANTABILITY; (B) WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE; OR (C) WARRANTY AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY

RIGHTS OF A THIRD PARTY; WHETHER EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE

OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE. Customer shall be responsible for determining that a

Product is suitable for Customer’s use and that such use complies with any applicable local, state or federal law.

(b) The Company shall not be liable for a breach of the warranty set forth in paragraph (a) if (i) the defect is a

result of Customer’s failure to store, install, commission or maintain the Product according to specicaons; (ii)

Customer alters or repairs such Product without the prior wrien consent of Company.

sole discreon, either (i) repair or replace the Product; or (ii) credit or refund the price of Product provided that,

if Company so requests, Customer shall, at Company’s expense, return such Product to Company.

(d) THE REMEDIES SET FORTH IN PARAGRAPH (c) SHALL BE THE CUSTOMER’S SOLE AND EXCLUSIVE

REMEDY AND COMPANY’S ENTIRE LIABILITY FOR ANY BREACH OF THE LIMITED WARRANTY SET

FORTH IN PARAGRAPH (a).

BY INSTALLING THIS PRODUCT, YOU AGREE TO THE TERMS OF THIS WARRANTY, AS WELL AS ALL OTHER

DISCLAIMERS AND WARRANTIES IN THIS DOCUMENT.

red lion DA High Speed Rate Counter Module Manuel utilisateur

Marque: red lion

Modèle: DA High Speed Rate Counter Module

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: red lion DA High Speed Rate Counter Module User manual

Documents connexes

Autres documents

Sixnet RAM 9000 Hardware Guide d'installation