red lion DA 4UI and 2UI MIX I/O Modules Manuel utilisateur

Marque: red lion

Modèle: DA 4UI and 2UI MIX I/O Modules

Taper: Manuel utilisateur

Installation DAMIX - A

Drawing No. LP1149

Effective 09/2020

DA 4UI and 2UI MIX I/O Modules

Installation Guide

FOR USE IN HAZARDOUS LOCATIONS:

Class I, Division 2, Groups A, B, C, and D

LISTED

IND.CONT. EQ.

E317425

MODULE PACKAGE CHECKLIST

This product package should contain the items listed below. If

any items are missing or damaged, contact Red Lion immediately.

- DIN Rail Mount DA Mix Module

- Installation Guide

GENERAL DESCRIPTION

The DA Mix modules are available in two configurations for use

with the DA70 controllers. The 4UI Mix module has 4 universal

inputs, 3 digital inputs/outputs, and 2 analog outputs. The 2UI

Mix module has 2 universal inputs, 8 digital inputs/outputs, and 2

analog outputs.

The design of the system provides a modular platform for

multi-zone control applications. The modules can accept a wide

range of thermocouple, RTD, 0-10 V, 0/4-20 mA signals, multiple

discrete inputs/outputs, and analog outputs.

The modules connect and communicate via proprietary

backplane to the DA host device. The DA host device, equipped

with serial ports as well as an Ethernet port(s), allows the system

to share data with PCs, PLCs, and SCADA systems.

Internal power management circuits allow the module to be

replaced while power is applied, in non-hazardous locations only,

which reduces downtime in the event of a module failure. All

configuration information is stored locally within the module, as

well as in the Host, so replacement modules do not need to be

configured.

CONFIGURATION

The DA Mix modules are configured with Windows

compatible

Crimson

software. The software is an easy to use, graphical

interface which provides a means of configuring and commissioning

new systems, as well as routine module re-calibration.

ALARMS

Each Universal Input channel has an alarm LED that illuminates

to indicate a fault.

SAFETY SUMMARY

All safety related regulations, local codes as well as instructions

that appear in this document or on equipment must be observed

to ensure personal safety and to prevent damage to either the

device or equipment connected to it.

Do not use these products to replace proper safety interlocking.

No software-based device (or any other solid-state device) should

ever be designed to be responsible for the maintenance of

personnel safety or consequential equipment not equipped with

safeguards. Red Lion disclaims any responsibility for damages,

either direct or consequential, that result from the use of this

equipment in a manner not consistent with these specifications.

CAUTION: Risk of Danger

Read complete instructions prior to installation and

operation of the unit.

ATTENTION : Risque de danger

Lire les instructions complètes avant l’installation et

l’utilisation de l’appareil.

WARNING - EXPLOSION HAZARD - SUBSTITUTION

OF COMPONENTS MAY IMPAIR SUITABILITY FOR

CLASS I, DIVISION 2

AVERTISSEMENT - DANGER D’EXPLOSION - LE

REMPLACEMENT DE COMPOSANTS PEUT NUIRE À

L’APTITUDE À LA CLASSE I, DIVISION 2

z Two models offering mix of inputs and outputs

4UI Mix - 4 Universal Inputs, 3 DI/DO and 2 Analog Outputs

2UI Mix - 2 Universal Inputs, 8 DI/DO and 2 Analog Outputs

z Universal inputs accept TC, RTD, 0-10 V and 0/4-20 mA signals

z Digital inputs and outputs (software selectable)

z Analog outputs capable of multiple ranges

z Configured using Crimson

software (version 3.2 or later)

II 3 G Ex ec IIC T4 Gc

DEMKO 20 ATEX 2268X

IECEx UL 20.0007X

0.49

(12.51)

0.45 (11.50)

4.53 (114.97)

6.22

(157.91)

1.91

(48.51)

1.35

(34.32)

6.00

(152.40)

DIMENSIONS In Inches (mm)

Drawing No. LP1149 Effective 09 2020

This equipment is suitable for use in Class I, Division 2,

Groups A, B, C, D, or non-hazardous locations only.

Cet équipement est adapté à une utilisation dans des

endroits de classe I, Division 2, Groupes A, B, C, D, ou

dans des endroits non dangereux seulement.

SPECIFICATIONS

1. POWER REQUIREMENTS:

Power is supplied by the DA host device. Modules may be

hot-swapped (replaced while powered up) in non-hazardous

locations only.

4UI Mix Max Power: 2.7 W

2UI Mix Max Power: 2.6 W

2. LEDs: (model dependent)

STS - A status LED to show general module status

Al1-Al4 - One alarm LED for each universal input channel

DIO1-DIO8 - One LED indicator for each Digital I/O point

3. MEMORY: Non-volatile memory retains all programmable

parameters. The controller also stores the parameters in order

to reprogram any modules that need updates.

4. UNIVERSAL INPUTS:

GENERAL:

Sample Time: 50 msec nominal; software configurable from

4 msec to 1200 msec

Common Mode Rejection: >110 dB, 50/60 Hz

Normal Mode Rejection: >50 dB, 50/60 Hz

Temperature Coefficient: 0.01%/

Step Response Time: 100 msec typ., 200 msec max

THERMOCOUPLE INPUT:

Types: T, E, J, K, R, S, B, N, C

Slope & Offset: Provides sensor error correction

Input Impedance: 20 M ohm

Lead Resistance Effect: 0.25 µV/ohm

Cold Junction Compensation: Less than ±1 °C typical (±1.5

°C max) over -40 to 75 °C ambient temperature

Resolution: 0.1

TYPE

MEASUREMENT

RANGE

WIRE COLOR

ANSI BS 1843

-200 to +400 °C

-328 to +752 °F

(+) Blue

(-) Red

(+) White

(-) Blue

-200 to +730 °C

-328 to +1346 °F

(+) Violet

(-) Red

(+) Brown

(-) Blue

-200 to +760 °C

-328 to +1400 °F

(+) White

(-) Red

(+) Yellow

(-) Blue

-200 to +1350 °C

-328 to +2462 °F

(+) Yellow

(-) Red

(+) Brown

(-) Blue

0 to +1768 °C

+32 to +3214 °F

No Standard

(+) White

(-) Blue

0 to +1768 °C

+32 to +3214 °F

No Standard

(+) White

(-) Blue

+149 to +1820 °C

+300 to +3308 °F

No Standard No Standard

-200 to +1300 °C

-328 to +2372 °F

(+) Orange

(-) Red

(+) Orange

(-) Blue

C W5/W6

0 to +2315 °C

+32 to +4199 °F

No Standard No Standard

mV 0 mV to 50 mV N/A N/A

Temperature Indication Accuracy: ± (0.3% of span, +1 °C).

Includes NIST conformity, cold junction effect, A/D

conversion errors, temperature coefficient and

linearization conformity at 23 °C after 20 minute warm up.

Probe Break Response: Upscale drive, Input Fault Alarm bit

set high, ALM LED illuminates.

RTD INPUT:

Type: 2 or 3 wire

Excitation: 150 µA

Lead Resistance: 15 ohms Max

Resolution: 1 or 0.1°

TYPE INPUT TYPE RANGE

385 100 ohm platinum, Alpha = 0.00385

-200 to +600 °C

-328 to +1100 °F

392 100 ohm platinum, Alpha = 0.003919

-200 to +600 °C

-328 to +1100 °F

672 120 ohm nickel, Alpha = 0.00672

-80 to +215 °C

-112 to +419 °F

Slope & Offset: Provides sensor error correction

Temperature Indication Accuracy: Includes NIST conformity,

A/D conversion errors, temperature coefficient and

linearization conformity at 23 °C after 20 minute warm up.

Probe Break Response: If channel is enabled: upscale drive,

Input

Fault Alarm bit set high, ALM LED illuminates

CURRENT INPUT:

Ranges: 0-20 mA or 4-20 mA

Programmable Scaling: ±30,000

Input Impedance: 10 Ohm

Max. Continuous Overload: 100 mA

Accuracy: ±0.1% of span

Input Fault Response: Upscale Drive, Input Fault Alarm bit

set high, ALM LED illuminates below -2 mA, and above

22 mA for 0-20 mA range; below +2 mA and above 22

mA for 4-20 mA signals.

VOLTAGE INPUT:

Ranges: 0-10 VDC

Programmable Scaling: ±30,000

Input Impedance: 1 M Ohm

Max. Continuous Overload: 50 V

Accuracy: ±0.1% of span

Input Fault Response: Upscale Drive, Input Fault Alarm bit

set high, ALM LED illuminates below -0.5 and above

+10.5 VDC.

5. DIGITAL INPUTS:

8 or 3 channels (model dependent)

Maximum input voltage: 30 VDC, reverse polarity protected

Guaranteed ON voltage: 3.8 V

Guaranteed OFF voltage: 1.2 V

Sinking Impedance: 20K Ohm

Selectable hardware Filter: 50 Hz or 500 Hz

6. DIGITAL OUTPUTS:

8 or 3 (model dependent) solid state N-channel open drain

MOSFETs

Rating: 1 ADC max

ON: < 0.2 V @ 1 A

MAX: 30 VDC

Offstate leakage current: 0.5 μA max

Isolation Level: 500 Vrms @ 50/60 Hz for 1 minute

7. AO – ANALOG OUTPUTS:

Two (2) independently configured. The outputs are not

isolated from each other, but are isolated from the power

supply and all other I/O.

Software programmable for 0-5 VDC, -10 VDC to 10 VDC,

0-20 mA, and 4-20 mA

Effective Resolution: Full 16-bit (Signed)

Voltage: 500 μV

Current: 1 μA

Accuracy: 0.2% of full scale (-40 to 70 °C)

Isolation Level: 500 Vrms @ 50/60 Hz for 1 minute

WARNING - EXPLOSION HAZARD. NOT HOT

SWAPPABLE. DO NOT REMOVE OR REPLACE WHILE

CIRCUIT IS LIVE UNLESS THE AREA IS FREE OF

IGNITIBLE CONCENTRATIONS.

AVERTISSEMENT - RISQUE D’EXPLOSION. NON

ÉCHANGEABLE À CHAUD. NE PAS RETIRER OU

REMPLACER SOUS TENSION SAUF SI LA ZONE EST

EXEMPTE DE CONCENTRATIONS INFLAMMABLES.

Effective 09 2020 Drawing No. LP1149

8. COMMUNICATIONS: Provided by the DA70 controller

9. ENVIRONMENTAL CONDITIONS:

Operating Temperature Range: -40 to 75 °C

Storage Temperature Range: -40 to 85 °C

Operating and Storage Humidity: 0 to 85% max. RH non-

condensing

Vibration to IEC 60068-2-6: Operational 5-500 Hz, 2 g

Shock to IEC 60068-2-27: Operational 15 g

Altitude: Up to 2000 meters

Installation Category II, Pollution Degree 2 as defined in IEC/

EN 60664-1.

10. CERTIFICATIONS AND COMPLIANCES:

CE Approved

EN 61326-1 Immunity to Industrial Locations

Emission CISPR 11 Class A

IEC/EN 61010-1

RoHS Compliant

ATEX Approved

II 3 G Ex ec IIC T4 Gc

DEMKO 20 ATEX 2268X

IECEx Approved

IECEx UL 20.0007X

UL Hazardous: File # E317425

Rugged IP30 enclosure

11. CONNECTIONS: Removable wire clamp screw terminal

blocks

Wire Strip Length: 0.3" (7.5 mm)

Wire Gauge Capacity: 14 to 24 AWG (2.08 to 0.20 mm

)

copper wire only

Torque: 2 inch-lbs (0.23 N-m)

12. CONSTRUCTION: Plastic enclosure with IP30 rating. For

use only in an approved enclosure.

13. MOUNTING REQUIREMENTS: Mounts onto standard DIN

style top hat (T) profile mounting rails according to EN50022

– 35 x 7.5 mm and 35 x 15 mm.

14. WEIGHT:

2UI Mix: 11.3 oz (320 g)

4UI Mix: 11.5 oz (326 g)

HARDWARE INSTALLATION

Removing Module From Cradle

To remove the module from the cradle, push in the module

release button at the top of the cradle and pull the module out of

the cradle.

MODULE

CRADLE

Attaching the Module/Cradle to the DIN Rail

The DIN rail should be mounted horizontally so that the unit’s

ventilation holes are vertical in relation to installation orientation.

A minimum clearance of 1 inch (25.4 mm) should be maintained

above and below the unit to ensure proper thermal regulation.

The cradle can be installed on the DIN rail with or without the

module attached. Ensure the DIN rail lock latch is in the outward

most position (unlocked). Hook the top back of the cradle DIN rail

clip over the DIN rail. Press the cradle until flush with the rail and

push the DIN rail lock latch to the latched (in) position.

For hazardous location

installation, the following shall be

taken into consideration:

— The equipment shall only be

used in an area of at least

pollution degree 2, as

defined in EN/IEC 60664-1.

— The equipment shall be

installed in an enclosure that

provides a minimum ingress

protection of IP54 in

accordance with EN/IEC

60079-0. The enclosure

shall be accessible only with

the use of a tool.

— Transient protection shall be provided that is set at a level

not exceeding 140% of the peak rated voltage value at the

supply terminals to the equipment.

Installing Module into Cradle

Push module into cradle until you hear an audible click

indicating it is properly latched.

MODULE HOT SWAPPING

If the area is known to be non-hazardous (free of ignitable

concentrations), then a module can be removed and/or installed

into a cradle attached to the controller while power is applied.

However, it is NOT recommended to connect to or remove from

the controller, a module/cradle pair or group of modules/cradles,

while power is applied. The power should be turned off anytime

a cradle or group of cradles (with or without modules) is plugged

into or removed from the controller.

DIN RAIL LOCK LATCH

Unlock Lock

MODULE CRADLE

DIN

rail

Drawing No. LP1149 Effective 09 2020

WIRING

All power, input and output (I/O) wiring must be in accordance

with Class I, Division 2 wiring methods and in accordance with

the authority having jurisdiction.

All conductors should meet voltage and current ratings for each

terminal. When wiring the module, use the numbers on the label

to identify the position number with the proper function. Strip

the wire, leaving approximately 0.3" (7.5 mm) of bare wire

exposed. Insert the wire into the terminal, and tighten.

WIRING CONNECTIONS

Universal Input Wiring

THERMOCOUPLE VOLTAGE

RTD CURRENT

Digital I/O Wiring

The DA Mix Module offers either 8 or 3 digital inputs/NFET

outputs. The digital inputs and outputs operate on the same

voltage that powers the unit. Pluggable screw block terminals are

provided for the I/O wiring connections. Refer to the following

diagrams on how to make your I/O connections. These diagrams

show the 2UIN terminal numbers. Reference the full unit label

shown for 4UIN terminal numbers.

Analog Output Wiring

CAUTION: Only UL listed wiring with temperature

ratings greater than 90 °C permitted for Class I, Division

2, Zone 2 and ATEX/IECex installations.

ATTENTION: Seul le câblage homologué UL avec des

températures nominales supérieures à 90°C est autorisé

pour les installations de classe I, Division 2 , zone 2 et

ATEX/IECex.

Terminals 17 to 24

Terminals 25 to 32

Terminals 9 to 16

Terminals 1 to 8

0-10V

4-20mA

INPUT COM

TC/RTD+

RTD +EXC

INPUT COM

TC/RTD+

RTD +EXC

0-10V

4-20mA

V+

I+

COM

V+

I+

DI/DO6+

DI/DO7-

DI/DO6-

DI/DO7+

DI/DO8-

DI/DO8+

DI/DO5+

DI/DO5-

DI/DO2+

DI/DO3-

DI/DO2-

DI/DO3+

DI/DO4-

DI/DO4+

DI/DO1+

DI/DO1-

INPUT

ANALOG

OUTPUT

DIGITAL I/O

0-10V

4-20mA

INPUT COM

TC/RTD+

RTD +EXC

INPUT COM

TC/RTD+

RTD +EXC

0-10V

4-20mA

V+

I+

COM

V+

I+

0-10V

4-20mA

INPUT COM

TC/RTD+

RTD +EXC

INPUT COM

TC/RTD+

RTD +EXC

0-10V

4-20mA

DI/DO1+

DI/DO2-

DI/DO1-

DI/DO2+

DI/DO3-

DI/DO3+

INPUTINPUT

ANALOG

OUTPUT

DIGITAL I/O

2UI MIX 4UI MIX

0-10V

4-20 mA

INPUT COM

TC/RTD+

RTD +EXC

0-10V

4-20 mA

INPUT COM

TC/RTD+

RTD +EXC

VDC-

VDC+

0-10V

4-20 mA

INPUT COM

TC/RTD+

RTD +EXC

LOAD

POWER

0-10V

4-20 mA

INPUT COM

TC/RTD+

RTD +EXC

DI/DO5-

DI/DO2+

DI/DO3-

DI/DO2-

DI/DO3+

DI/DO4-

DI/DO4+

DI/DO1+

DI/DO1-

DIGITAL I/

Input Connections - 2UI shown

DI/DO5-

DI/DO2+

DI/DO3-

DI/DO2-

DI/DO3+

DI/DO4-

DI/DO4+

DI/DO1+

DI/DO1-

DIGITAL I/

Load

Solid State NFET Output Connection - 2UI shown

Recorder,

Controller,

Valve, etc

4-20mA

V+

I+

COM

V+

I+

ANALOG

OUTPUT

Voltage Analog Output

Recorder,

Controller,

Valve, etc

4-20mA

V+

I+

COM

V+

I+

ANALOG

OUTPUT

Current Analog Output

Effective 09 2020 Drawing No. LP1149

LEDS

Status LED

LED

COLOR(S)

LED STATE MEANING

Blue 3 quick flashes Module is booting.

Green Solid Module is configured and running.

Green/Off Flashing Module is running but is not

configured.

Green/

Purple

Flashing Module is performing calibration.

Red/Green Flashing Module is running but

communication with the controller

is inactive. If status persists, contact

technical support.

Red/Off Flashing An internal error has occurred. If

status persists, contact technical

support.

Yellow/Off Flashing Module position is unassigned. If

status persists, contact technical

support.

Off Solid Module application is not running or

the module is not powered. If status

persists, contact technical support.

Alarm LEDs

Each universal analog input has an alarm LED that is factory

configured to indicate an input value that is out of range. A red

LED is lit when an alarm condition is present. Otherwise the LED

is off.

RED LION CONTROLS TECHNICAL SUPPORT

If for any reason you have trouble operating, connecting, or

simply have questions concerning your new DA Module, contact

Red Lion’s technical support.

Support: support.redlion.net

Website: www.redlion.net

Inside US: +1 (877) 432-9908

Outside US: +1 (717) 767-6511

Red Lion Controls, Inc.

20 Willow Springs Circle York, PA 17406

ORDERING INFORMATION

PART NUMBER DESCRIPTION

DAM00I0IN4DA0000

DA Series I/O Mix Module with 4UI

DAM00I0IN2DA0000

DA Series I/O Mix Module with 2UI

A listing of the entire DA Series family of products and accessories

can be found at www.redlion.net.

Drawing No. LP1149 Effective 09 2020

This page intentionally left blank.

Effective 09 2020 Drawing No. LP1149

This page intentionally left blank.

company and product names are trademarks of their respective owners.

LIMITED WARRANTY

(a) Red Lion Controls Inc. (the “Company”) warrants that all Products shall be free from defects in material and

workmanship under normal use for the period of me provided in “Statement of Warranty Periods” (available at

www.redlion.net) current at the me of shipment of the Products (the “Warranty Period”). EXCEPT FOR THE

ABOVE-STATED WARRANTY, COMPANY MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE

PRODUCTS, INCLUDING ANY (A) WARRANTY OF MERCHANTABILITY; (B) WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE; OR (C) WARRANTY AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY

RIGHTS OF A THIRD PARTY; WHETHER EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE

OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE. Customer shall be responsible for determining that a

Product is suitable for Customer’s use and that such use complies with any applicable local, state or federal law.

(b) The Company shall not be liable for a breach of the warranty set forth in paragraph (a) if (i) the defect is a

result of Customer’s failure to store, install, commission or maintain the Product according to specicaons; (ii)

Customer alters or repairs such Product without the prior wrien consent of Company.

sole discreon, either (i) repair or replace the Product; or (ii) credit or refund the price of Product provided that,

if Company so requests, Customer shall, at Company’s expense, return such Product to Company.

(d) THE REMEDIES SET FORTH IN PARAGRAPH (c) SHALL BE THE CUSTOMER’S SOLE AND EXCLUSIVE

REMEDY AND COMPANY’S ENTIRE LIABILITY FOR ANY BREACH OF THE LIMITED WARRANTY SET

FORTH IN PARAGRAPH (a).

BY INSTALLING THIS PRODUCT, YOU AGREE TO THE TERMS OF THIS WARRANTY, AS WELL AS ALL OTHER

DISCLAIMERS AND WARRANTIES IN THIS DOCUMENT.

red lion DA 4UI and 2UI MIX I/O Modules Manuel utilisateur

Marque: red lion

Modèle: DA 4UI and 2UI MIX I/O Modules

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: red lion DA 4UI and 2UI MIX I/O Modules User manual

red lion DA 4UI and 2UI MIX I/O Modules Manuel utilisateur

red lion DA 4UI and 2UI MIX I/O Modules Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents