KAGA FEI EC2820 Bluetooth Low Energy Module Manuel utilisateur

Marque
KAGA FEI
Modèle
EC2820 Bluetooth Low Energy Module
Taper
Manuel utilisateur
19-Dec.2022 Ver.0.1
KAGA FEI Co., Ltd.
KAGA FEI Co., Ltd.
1/5
E
C
2
8
2
0
User manual
(for EC2820)
FCC ID: 2A6NFEC2820
IC: 28568-EC2820
19-Dec.2022 Ver.0.1
KAGA FEI Co., Ltd.
KAGA FEI Co., Ltd.
2/5
E
C
2
8
2
0
This module should be installed in the host device according to the interface specification.
1) Japan Regulatory Information
a) This module is approved with the specific antenna on this module.
b) Please ensure that your product can bear a label with the following information. If the
product is so small that it is not practicable to place the label, please place it in the
instruction manual and package.
This product installs a radio system which has been approved as a radio station in a
low power data communication system based on the Radio Law.
EC2820 : 005-103119
2) Canada Regulatory Information
The following information must be indicated on the host device of this module;
a) This device complies with Innovation, Science and Economic Development Canada’s
applicable licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’ Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :
1) l’appareil ne doit pas produire de brouillage;
2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
b) This product is certified as type of the portable device with Science and Economic
Development Canada Rules. To maintain compliance with RF Exposure requirement,
please use within specification of this product and have a separation distance of
minimum 15 mm between the user and/or bystander and the antenna and /or radiating
element.
This distance ensures that the output power (e.i.r.p.) of EC2820 is below the SAR
evaluation Exemption limits defined in RSS-102 issue 5.
Ce produit est certifié comme type de l'appareil portable avec Règles de Innovation,
Sciences et Développement économique Canada. Pour maintenir l'acquiescement
avec exigence Exposition de RF, veuillez utiliser dans spécification de ce produit et
respecter une distance de séparation d'au moins 15 mm entre l'utilisateur et / ou un
tiers et l'antenne et / ou l'élément rayonnant.
Cette distance garantit que la puissance de sortie (p.i.r.e.) d’EC2820 est inférieure aux
limites d’exemption de l’évaluation SAR définies dans le numéro 5 de la norme
RSS-102.
- IC: 28568-EC2820
19-Dec.2022 Ver.0.1
KAGA FEI Co., Ltd.
KAGA FEI Co., Ltd.
3/5
E
C
2
8
2
0
c) Please notify certified ID by either one of the following method on your product.
-Contains IC : 28568-EC2820
Specifiez ID certifiée dans votre produit par une de méthode suivante.
-Contains IC : 28568-EC2820
3) FCC Regulatory Information
a) This device complies with part 15 of the FCC Rules.
-Part 15 Subpart C
b) The following statement shall be indicated on the host device or the user manual of the
host device; Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
c) Please notify certified ID by either one of the following method on your product.
-Contains Transmitter Module FCC ID: 2A6NFEC2820
-Contains FCC ID: 2A6NFEC2820
d) The following statement shall be indicated in the user manual of the host device;
CAUTION: Changes or modifications not expressly approved by the party responsible
for compliance could void the use’s authority to operate the equipment.
e) The modular transmitter is only FCC authorized for the specific rule parts (Part 15
Subpart C) listed on the grant, and the host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not covered by the modular
transmitter grant of certification. The final host product still requires Part 15 Subpart B
compliance testing with the modular transmitter installed.
f) This product is certified as type of the portable device with FCC Rules. To maintain
compliance with RF Exposure requirement, please use within specification of this
product.
g) The following statement shall be indicated in the user manual of the host device; The
antenna used for this transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
h) This module can change the output power depending on the circumstances by the
application software which is developed by module installer. Any end user cannot
change the output power.
i) Antenna List
No.1
Antenna Category Monopole
Antenna Type PCB antenna
Dimensions 9.0mm x 2.7mm
4) CE Regulatory Information
a) When your end product installs this module, it is required to proceed additional
certification processes before placing on the market in EU member states to make your
products fully comply with relative EU standards.
b) KAGA FEI can provide you the test reports of conducted measurement portion for the
radio module. You can utilize the test reports for the certification processes of your
end product as it requires radio testing.
19-Dec.2022 Ver.0.1
KAGA FEI Co., Ltd.
KAGA FEI Co., Ltd.
4/5
E
C
2
8
2
0
Control No.
(1/2)
Control name
Pin Layout
Pin Descriptions
Pin Pin name Pin function
Description
1 VDD Power Power supply
2 VDDH Power High voltage power supply
3 GND Power Ground
4 VBUS Power 5 V input for USB 3.3 V regulator
5 GND Power Ground
6 D- USB USB D-
7 D+ USB USB D+
8 GND Power Ground
9 P0.04
AIN2
Digital I/O
Analog input
General purpose I/O
Analog input
10 P0.05
AIN3
Digital I/O
Analog input
General purpose I/O
Analog input
11 P0.06 Digital I/O General purpose I/O
12 P0.07 Digital I/O General purpose I/O
13 GND Power Ground
14 SWDIO Debug Serial wire debug I/O for debug and programming
15 SWDCLK Debug Serial wire debug clock input for debug and
programming
16 P0.15 Digital I/O General purpose I/O
17 P0.20 Digital I/O General purpose I/O
18 P0.17 Digital I/O General purpose I/O
19 P0.16 Digital I/O General purpose I/O
20 P0.18
RESET Digital I/O General purpose I/O
Configurable as pin RESET (Factory default : GPIO)
21 GND Power Ground
22 OUT_MOD RF In/Out RF I/O pin. It should be connected to Pin 23
OUT_ANT for normal operation.
23 OUT_ANT Antenna
In/Out
Internal antenna. It should be connected to Pin 22
OUT_MOD for normal operation.
24 P0.02
AIN0
Digital I/O
Analog input
General purpose I/O
Analog input
25 P0.03
AIN1
Digital I/O
Analog input
General purpose I/O
Analog input
19-Dec.2022 Ver.0.1
KAGA FEI Co., Ltd.
KAGA FEI Co., Ltd.
5/5
E
C
2
8
2
0
Control No.
(2/2)
Control name
Pin Layout
Pin Pin name Pin function
Description
26 P0.28 Digital I/O General purpose I/O
27 P0.30 Digital I/O General purpose I/O
28 - 36 GND Power Ground
37 P0.14 Digital I/O General purpose I/O
38 GND Power Ground
39 P0.29 Digital I/O General purpose I/O
40 P0.08 Digital I/O General purpose I/O
41 - 43 GND Power Ground
44 GND Power Ground Center pad
45 GND Power Ground Center pad
46 GND Power Ground Corner pad
47 GND Power Ground Corner pad
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

KAGA FEI EC2820 Bluetooth Low Energy Module Manuel utilisateur

Marque
KAGA FEI
Modèle
EC2820 Bluetooth Low Energy Module
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents