KAGA FEI EJ2832 Bluetooth Low Energy and ANT Module Manuel utilisateur

Marque
KAGA FEI
Modèle
EJ2832 Bluetooth Low Energy and ANT Module
Taper
Manuel utilisateur
12-Dec.2022 Ver.0.1
KAGA FEI Co., Ltd.
KAGA FEI Co., Ltd. 1/5
EJ2832
User manual
(for EJ2832)
FCC ID: 2A6NFEJ2832
IC: 28568-EJ2832
12-Dec.2022 Ver.0.1
KAGA FEI Co., Ltd.
KAGA FEI Co., Ltd. 2/5
EJ2832
This module should be installed in the host device according to the interface specification.
1) Japan Regulatory Information
a) This Product is a radio system and obtained certification of construction type combined
with the specific antenna.
b) Please ensure that your product has a label with the following certification mark at easily
viewable location. If your product is too small to have the label, please place it in the
instruction manual and package of your product. The mark diameter shall be easily
legible. In case your product does not have the label with the following certification mark,
you or your customer who uses your product may be against the Radio Law and
subjected to criminal punishment. KAGA FEI shall not be liable for any loss or damage
incurred by you or your customer arising from use of your product which does not have
following certification mark.
This product installs a radio system which has been approved as a radio station in a
low power data communication system based on the Radio Law.
EJ2832 : 005-103120
2) Canada Regulatory Information
The following information must be indicated on the host device of this module;
a) This device complies with Innovation, Science and Economic Development Canada’s
applicable licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’ Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :
1) l’appareil ne doit pas produire de brouillage;
2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
b) This product is certified as type of the portable device with Science and Economic
Development Canada Rules. To maintain compliance with RF Exposure requirement,
please use within specification of this product.
Ce produit est certifié comme type de l'appareil portable avec Règles de Innovation,
Sciences et Développement économique Canada. Pour maintenir l'acquiescement
avec exigence Exposition de RF, veuillez utiliser dans spécification de ce produit.
- IC: 28568-EJ2832
c) Please notify certified ID by either one of the following method on your product.
-Contains IC : 28568-EJ2832
Specifiez ID certifiée dans votre produit par une de méthode suivante.
-Contains IC : 28568-EJ2832
12-Dec.2022 Ver.0.1
KAGA FEI Co., Ltd.
KAGA FEI Co., Ltd. 3/5
EJ2832
3) FCC Regulatory Information
a) This device complies with part 15 of the FCC Rules.
-Part 15 Subpart C
b) The following statement shall be indicated on the host device or the user manual of the
host device; Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
c) Please notify certified ID by either one of the following method on your product.
-Contains Transmitter Module FCC ID: 2A6NFEJ2832
-Contains FCC ID: 2A6NFEJ2832
d) Since there is no space which indicates FCC ID on this module, FCC ID is indicated in
a manual. If the FCC ID is not visible when the module is installed inside another
device, then the module is installed must also display a label referring to the enclosed
module.
e) The following statement shall be indicated in the user manual of the host device;
CAUTION: Changes or modifications not expressly approved by the party responsible
for compliance could void the use’s authority to operate the equipment.
f) The modular transmitter is only FCC authorized for the specific rule parts (Part 15
Subpart C) listed on the grant, and the host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not covered by the modular
transmitter grant of certification. The final host product still requires Part 15 Subpart B
compliance testing with the modular transmitter installed.
g) This product is certified as type of the portable device with FCC Rules. To maintain
compliance with RF Exposure requirement, please use within specification of this
product.
h) The following statement shall be indicated in the user manual of the host device; The
antenna used for this transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
i) This module can change the output power depending on the circumstances by the
application software which is developed by module installer. Any end user cannot
change the output power.
j) Antenna List
No.1
Antenna Category
Monopole
Antenna Type
PCB antenna
Dimensions
3.45mm x 4.7mm
4) CE Regulatory Information
a) When your end product installs this module, it is required to proceed additional
certification processes before placing on the market in EU member states to make your
products fully comply with relative EU standards.
b) KAGA FEI can provide you the test reports of conducted measurement portion for the
radio module. You can utilize the test reports for the certification processes of your
end product as it requires radio testing.
12-Dec.2022 Ver.0.1
KAGA FEI Co., Ltd.
KAGA FEI Co., Ltd. 4/5
EJ2832
Control No. (1/2)
Control name
Pin Layout
Pin Descriptions
Pin
Pin function
Description
1
Ground
Ground pin. (0 V)
2
Digital I/O
Analog input
General purpose I/O pin.
Connection for 32.768kHz crystal (LFXO).
3
Digital I/O
Analog input
General purpose I/O pin
Connection for 32.768kHz crystal (LFXO).
4
Digital I/O
Analog input
General purpose I/O pin.
SAADC/COMP/LPCOMP input.
5
Power
Power supply pin.
6
Power
1V3 regulator supply decoupling.
Input from DC/DC converter. Output from 1.3 V LDO.
7
NFC input
Digital I/O
NFC antenna connection.
General purpose I/O pin.
8
NFC input
Digital I/O
NFC antenna connection.
General purpose I/O pin.
9
Ground
Ground pin. (0 V)
10
Digital I/O
General purpose I/O pin
Trace port output.
11
Digital I/O
General purpose I/O pin.
Trace port clock output.
12
Ground
Ground pin. (0 V)
13
Antenna In/Out
Internal antenna. It should be connected to Pin 14
OUT_MOD for normal operation.
14
RF In/Out
RF I/O pin. It should be connected to Pin 13 OUT_ANT for
normal operation.
15
Ground
Ground pin. (0 V)
16
Digital I/O
Serial Wire Debug I/O for debug and programming
17
Digital input
Serial Wire Debug clock input for debug and
programming
18
Digital I/O
General purpose I/O pin
Configurable as system RESET pin.
(Factory default : GPIO)
19
Digital I/O
General purpose I/O pin.
20
Ground
Ground pin. (0 V)
21
Digital I/O
General purpose I/O pin.
22
Digital I/O
General purpose I/O pin.
12-Dec.2022 Ver.0.1
KAGA FEI Co., Ltd.
KAGA FEI Co., Ltd. 5/5
EJ2832
Control No. (2/2)
Control name
Pin Layout
Pin
Pin function
Description
23
Digital I/O
Analog input
General purpose I/O pin.
SAADC/COMP/LPCOMP input.
24
Power
DC/DC converter output pin.
25
Digital I/O
Analog input
General purpose I/O pin.
SAADC/COMP/LPCOMP input.
26
Digital I/O
Analog input
General purpose I/O pin.
SAADC/COMP/LPCOMP input.
27
Digital I/O
Analog input
General purpose I/O pin.
SAADC/COMP/LPCOMP input.
28
Ground
Ground pin. (0 V)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

KAGA FEI EJ2832 Bluetooth Low Energy and ANT Module Manuel utilisateur

Marque
KAGA FEI
Modèle
EJ2832 Bluetooth Low Energy and ANT Module
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents