Espressif ESP32-MINI-1 AMH Hand Controller Mode d'emploi

ESP32-MINI-1 AMH Hand Controller
Marque
Espressif
Modèle
ESP32-MINI-1 AMH Hand Controller
Taper
Mode d'emploi
AMH Hand Controller User Guide
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FCC ID:2AC7Z-ESP32MINI1
FCC statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
·If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF exposure warning
The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment.
The equipment must not be co-located or operating in conjunction with any other antenna or
transmitter.
NOTE: Any changes or modifications not expressly approved by the grantee of this device could
void the user's authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio
électrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
IC RSS-Gen antenna statement
This radio transmitter (IC: 8853A-C8) has been approved by
Industry Canada
to operate
with the antenna types listed below with the maximum permissible gain indicated.
Antenna types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio
(
IC:
8853A-C8
)
a été approuvé par Industrie Canada pour
fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible
maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au
gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
Radiation Exposure Statement:
The equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. The equipment must not be co-located or operating in conjunction with any other
antenna or transmitter.
Déclaration d'exposition aux radiations:
L'équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un
environnement non contrôlé. L'équipement ne doit pas être situé ou fonctionner en conjonction
avec une autre antenne ou un autre émetteur.
Light Indicator:
You can learn the status of the AM5 mount through the light colors once you connect the hand
controller to AM5 and power them.
Red: Equatorial Mode
Green: Altazimuth mode
Light on: High sidereal tracking rate
Light off: Low sidereal tracking rate
1. Directional Control Joystick:
The joystick knob can be pushed to multiple directions. Pressing down on it switches between
high and low slew speeds. There are 1, 2, 4, 8x sidereal rate at low speed, 20 to 1440x sidereal rate
at high speed.
How to switch between high and low speed: The default mode is at low tracking speed. Press
down on the joystick to switch to high tracking rate. Press again to switch back to low tracking
rate.
2. Tracking Button:
Press the button, backlight up: AM5 is now in tracking.
One press again, backlight off: Cancelling tracking.
3. Cancel Button:
Cancel: One press to cancel GOTO or other functions. Long press for 3 seconds to go to zero
position.
Equatorial/Azimuth Mode Switching: When AM5 Mount power is off, long press the cancel
button to activate the mount again along with the switch function. To enter Altazimuth mode,
press cancel button until the light indicator turns green. (How to identify the current mode of the
mount: After boot, Light Indicator red means Equatorial mode; Light indicator green means
Azimuth mode.)
WiFi: The WiFi function has been integrated in the hand controller, which allows a wireless
connection between the hand controller and ZWO ASIMount APP or ASIAIR.
If you forget the hand controllers WiFi password, you can press and hold the tracking and cancel
buttons, unplug its cable and then re-plug in, keep pressing the buttons for 3 seconds until the
indicator light flashes. The hand controller WiFi password will be restored to the default setting:
12345678.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Espressif ESP32-MINI-1 AMH Hand Controller Mode d'emploi

ESP32-MINI-1 AMH Hand Controller
Marque
Espressif
Modèle
ESP32-MINI-1 AMH Hand Controller
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Autres documents