Hui Zhou Gaoshengda Technology WXT2LM2611 Mode d'emploi

Marque
Hui Zhou Gaoshengda Technology
Modèle
WXT2LM2611
Taper
Mode d'emploi
Hui Zhou Gaoshengda Technology Co., LTD WXT2LM2611
PAGE 1 OF 4
Version 1.0
WIFI+BT Module
IEEE 802.11 a/b/g/n/ac/ax 2T/2R
Model Number: WXT2LM2611
Product Descrition
The WXT2LM2611 is a complete 2.4GHz/5GHz/6GHz WIFI 2×2 MIMO module. This module provides a high level of
integration with a dual-stream IEEE 802.11ax MAC/ base band /radio and Bluetooth 5.2.The WLAN operation
supports 20MHz,40MHz and 80MHz channels for data rates up to 1201Mbps. It fully complies with IEEE 802.11
a/b/g/n/ac/ax feature rich wireless connectivity at high standards,delivers reliable,cost-effective, throughput from
an extended distance.
Product Features
Product Specification
Model
WIF+BT Module
Product Name
WXT2LM2611
Standard
802.11 a/b/g/n/ac/ax
Interface
USB
Data Transfer Rate
1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,90,120 and maximum of 1201Mbps
Modulation Method
GFSK,π/4-DQPSK,8DPSK(bluetooth)
DQPSK,DBPSK,CCK(802.11b)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11g)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11n)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11a)
QPSK,BPSK,16QAM,64QAM,256QAM with OFDM (802.11ac)
QPSK,BPSK,16QAM,64QAM,256QAM,1024QAM with OFDMA (802.11ax)
Frequency Band
BLUETOOTH
2402~2480 MHz
WIFI
2.4G: 2412~2462 MHz
5G: 5150~5350MHz, 5470~5725MHz，5725~5850MHz
6G: 5925~7125MHz
Operation Mode
Infrastructure
Security
WEP, TKIP, AES, WPA, WPA2
Operating Voltage
3.3V±10%
Current Consumption
＜1000mA
Antenna Type
PIFA
Operating
Temperature
-10 ~ 70°C ambient temperature
Storage Temperature
-40 ~ 80°C ambient temperature
Humidity
5 to 95 % maximum (non-condensing)
◆ Complies with IEEE 802.11b/g/n/ax for 2.4GHz，IEEE 802.11a/n/ac/ax for 5GHz，IEEE 802.11ax
for 6GHz Wireless LAN.
◆ Bluetooth v5.2
◆ Two transmit and Two receive path(2T2R)
◆ Works with all existing network nfrastructure.
◆ Capable of up to 128-Bit WEP Encryption.
◆ Freedom to roam while staying connected.
◆ UP to 1201 Mbps High-Speed Transfer Rate in 802.11ax mode of operation.
◆ Operating Systems：Linux, Win10, Win11.
◆ Low power consumption.
◆ Easy to install and configure.
◆ High speed usd 2.0 interface.
◆ROHS compliant
Hui Zhou Gaoshengda Technology Co., LTD WXT2LM2611
PAGE 2 OF 4
Version 1.0
NOTICE:
◆please keep this product and accessories attached to the places which children can't touch;
◆do not splash water or other liquid onto this product, otherwise it may cause damage;
◆do not put this product near the heat source or direct sunlight, otherwise it may cause
deformation or malfunction;
◆please keep this product away from flammable or naked flame;
◆please do not repair this product by yourself. Only qualified personnel can be repaired.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
2.2
This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS and DSS) and
CFR 47 FCC Part 15 E (NII). It is applicable to the modular transmitter
2.3
This radio transmitter FCC ID: 2AC23-WXT2L has been approved by Federal Communications Commission to
operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in
this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this
device.
The concrete contents to check are the following three points.
１) Must use an antenna such as PIFA Antenna with a gain not exceeding 4.09 dBi for BT/BLE/2.4G WIFI, 4.09 dBi for 5G
WIFI, 6 dBi for 6G WIFI;
２) Should be installed so that the end user cannot modify the antenna;
３) Feed line should be designed in 50ohm
Fine-tuning of return loss etc. can be performed using a matching network.
The antenna shall not be accessible for modification or change by the end user
2.4
The module complies with FCC Part 15.247 / Part 15.407 and applies for Single module approval.
2.5
Trace antenna designs: Not Applicable, trace antennas not used, only externally connected PIFA antennas are allowed.
2.6
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must
not be co-located or operating in conjunction with any other antenna or transmitter.
Hui Zhou Gaoshengda Technology Co., LTD WXT2LM2611
PAGE 3 OF 4
Version 1.0
2.7
Antenna type and antenna gain:
WIFI Antennas:
2.4G Ant 0 & Ant 1
5G Ant 0 & Ant 1
6G Ant 0 & Ant 1
PIFA antenna: 4.09 dBi
PIFA antenna: 5.17 dBi
Maximum: PIFA antenna: 6 dBi
Minimum: PIFA antenna: 3.47 dBi
BT Antenna:
TYPE
GAIN
Ant 0: PIFA antenna
4.09 dBi
2.8
Please notice that if the FCC identification number is not visible when the module is installed inside another device, then
the outside of the device into which the module is installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains FCC ID: 2AC23-WXT2L” Any similar wording that
expresses the same meaning may be used.
2.9
Testing of the host product with all the transmitters installed – referred to as the composite investigation test- is
recommended, to verify that the host product meets all the applicable FCC rules. The radio spectrum is to be
investigated with all the transmitters in the final host product functioning to determine that no emissions exceed the
highest limit permitted for any one individual transmitter as required by Section 2.947(f). The host manufacturer is
responsible to ensure that when their product operates as intended it does not have any emissions present that are
out of compliance that were not present when the transmitters were tested individually.
If the modular transmitter has been fully tested by the module grantee on the required number of channels,
modulation types, and modes, it should not be necessary for the host installer to re-test all the available transmitter
modes or settings. It is recommended that the host product manufacturer, installing the modular transmitter, perform
some investigative measurements to confirm that the resulting composite system does not exceed the spurious
emissions limits or band edge limits (e.g., where a different antenna may be causing additional emissions).
The testing should check for emissions that may occur due to the intermixing of emissions with the other transmitters,
digital circuitry, or due to physical properties of the host product (enclosure). This investigation is especially important
when integrating multiple modular transmitters where the certification is based on testing each of them in a
stand-alone configuration.
2.10
Any company of the host device which install this modular should perform the test of radiated & condicted emission
and spurious emission etc. according to FCC Part 15C: 15.247, 15.209, & 15.207, Part 15E: 15.407, 15B class B
requirement, only if the test result complies with FCC part 15C: 15.247, 15.209, & 15.207, Part 15E: 15.407, 15B
class B requirement. Then the host can be sold legally.
The host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not
covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart
B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice
stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter
installed.
2.11
The host manufacture is recommended to use D04 Module Integration Guide recommending as "best practice" RF
design engineering testing and evaluation in case non-linear interactions generate additional non-compliant limits due
to module placement to host components or properties.
2.12
This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition
or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult
with module manufacturer for the installation method in end system.
Hui Zhou Gaoshengda Technology Co., LTD WXT2LM2611
PAGE 4 OF 4
Version 1.0
FCC Wi-Fi 6E statement
1. FCC regulations restrict the operation of this device to indoor use only.
2. The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that
operation of this device is permitted in large aircraft while flying above 10,000 feet.
3. Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with
unmanned aircraft systems.
This module cannot be installed in a weatherized enclosure and cannot operate from battery but only power sources.
The host device must be connected to a power source as it has no battery.
Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
Please notice that if the ISED certification number is not visible when the module is installed inside another device, then
the outside of the device into which the module is installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains IC: 12290A-WXT2L” any similar wording that expresses
the same meaning may be used.
l'appareil hôte doit porter une étiquette donnant le numéro de certification du module d'Industrie Canada, précédé des mots
« Contient un module d'émission », du mot «IC: 12290A-WXT2L» ou d'une formulation similaire exprimant le même sens,
comme suit
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference
to co-channel mobile satellite systems
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin
de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102
RF exposure, users can obtain Canadian information on RF exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 etla conformité à
l'exposition de RSS-102 RF, utilisateurs peut obtenir l'information canadienne surl'exposition et la conformité de rf.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment
should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ouémetteur. Cet
équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.
This radio transmitter [IC: 12290A-WXT2L] has been approved by Innovation, Science and Economic Development
Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not
included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for
use with this device.
The concrete contents to check are the following three points.
１) Must use an antenna such as PIFA Antenna with a gain not exceeding 4.09 dBi for BT/BLE/2.4G WIFI, 4.09 dBi for 5G
WIFI, 6 dBi for 6G WIFI;
２) Should be installed so that the end user cannot modify the antenna;
３) Feed line should be designed in 50ohm
Fine-tuning of return loss etc. can be performed using a matching network.
Hui Zhou Gaoshengda Technology Co., LTD WXT2LM2611
PAGE 5 OF 4
Version 1.0
Le présent émetteur radio [IC: 12290A-WXT2L] a été approuvé par Innovation, Sciences et Développement économique
Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types
d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la
liste, sont strictement interdits pour l'exploitation de l'émetteur.
Le contenu concret à vérifier sont les trois points suivants.
１) Les antennes telles que les antennes pifa doivent être utilisées avec un gain ne dépassant pas 4,09 DBI pour BT / ble /
2.4G wifi, 4,09 DBI pour 5G wifi et 6 DBI pour 6g wifi;
２) doivent être installés de façon que l'utilisateur final ne peut pas modifier l'antenne
３) La ligne d’alimentation doit être conçue en 50ohm
Le réglage précis de la perte de rendement, etc. peut être effectué en utilisant un réseau correspondant..
Antenna type and antenna gain:
WIFI Antennas:
2.4G Ant 0 & Ant 1
5G Ant 0 & Ant 1
6G Ant 0 & Ant 1
PIFA antenna: 4.09 dBi
PIFA antenna: 5.17 dBi
Maximum: PIFA antenna: 6 dBi
Minimum: PIFA antenna: 3.47 dBi
BT Antenna:
TYPE
GAIN
Ant 0: PIFA antenna
4.09 dBi
IC Wi-Fi 6E Statement:
Devices shall not be used for control of or communications with unmanned aircraft systems.
Low-power indoor access points and indoor subordinate devices shall bear statements acknowledging both of the following
restrictions in the user manual and, where feasible, in a conspicuous location on the device:
Operation shall be limited to indoor use only.
Operation on oil platforms, automobiles, trains, maritime vessels and aircraft shall be prohibited except for on large aircraft
flying above 3,048 m (10,000 ft).
L'équipement ne doit pas être utilisé pour le contrôle ou la communication des systèmes d'aéronefs sans pilote.
Les points d'accès intérieurs de faible puissance et les accessoires intérieurs doivent indiquer les restrictions suivantes dans
le manuel de l'utilisateur et, si possible, à un endroit bien en vue de l'appareil:
Le fonctionnement doit être limité à un usage intérieur.
Il est interdit de travailler sur les plates - formes pétrolières, les voitures, les trains, les navires maritimes et les aéronefs, à
l'exception des gros aéronefs de plus de 3 048 mètres (10 000 pieds).
Notice to OEM integrator
Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device
is installed and used at distances of at least 20cm from persons.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as
show in this manual(FCC/ICanada statement).
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable
requirements for the system such as Part 15 B, ICES 003.
Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when
the module is installed in the host.
Hui Zhou Gaoshengda Technology Co., LTD WXT2LM2611
PAGE 6 OF 4
Version 1.0
The use condition limitations extend to professional users, then instructions must state that this information also extends to
the host manufacturer’s instruction manual.
This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or
different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with
module manufacturer for the installation method in end system.
Any company of the host device which install this modular should perform the test of radiated & conducted emission and
spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement, only if the test
result comply with FCC part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement. Then the host can be sold legally.
This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.247 and 15.407) listed on the
grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not
covered by the modular transmitter grant of certification.
Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when
the module is installed in the host.
Must have on the host device a label showing Contains FCC ID: 2AC23-WXT2L or IC: 12290A-WXT2L.
Both FCC ID and IC ID are not to be placed on the host at the same time and only hosts going into the US can use the FCC
ID and only hosts going into Canada can use the IC ID.
Installer should put it in the manual：
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference
to co-channel mobile satellite systems
l'hôte doit utiliser l'instrument uniquement dans des dispositifs qui répondent à la fcc / (catégorie d'exposition rf mobile, ce
qui signifie le dispositif est installé et utilisé à une distance d'au moins 20 cm de personnes.
le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen déclarations de conformité relatives à l'émetteur que de
montrer dans ce manuel.
le fabricant est responsable de la conformité de l'hôte, le système d'accueil avec le module installé avec toutes les autres
exigences applicables du système comme la partie 15 b, ices - 003.
accueillir le fabricant est fortement recommandé de confirmer la conformité avec les exigences de la fcc / (émetteur lorsque
le module est installé dans l'hôte.
le dispositif d'accueil doivent avoir une étiquette indiquant contient FCC ID: 2AC23-WXT2L，IC: 12290A-WXT2L
Les personnes chargées de l'installation devraient figurer dans le manuel:
Les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur
afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
Doit avoir sur l'appareil hôte une étiquette indiquant Contient l'ID FCC: 2AC23-WXT2L ou IC : 12290A-WXT2L L'ID
FCC et l'ID IC ne doivent pas être placés sur l'hôte en même temps et seuls les hôtes se rendant aux États-Unis peuvent
utiliser l'ID FCC et seuls les hôtes se rendant au Canada peuvent utiliser l'ID IC.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Hui Zhou Gaoshengda Technology WXT2LM2611 Mode d'emploi

Marque
Hui Zhou Gaoshengda Technology
Modèle
WXT2LM2611
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents