Ryobi TSS702 Le manuel du propriétaire

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

7-1/4 in. SLIDING COMPOUND

MITER SAW WITH LED

SCIE À ONGLETS COMBINÉS

COULISSANTE AVEC DEL

DE 184 mm (7-1/4 po)

SIERRA INGLETEADORA

COMPUESTA DESLIZANTE CON DIODO

DE 184 mm (7-1/4 pulg.)

TSS702

WARNING: To reduce the

risk of injury, the user must read and

understand the operator’s manual

before using this product.

SAVE THIS MANUAL FOR

FUTURE REFERENCE

ADVERTENCIA: Para reducir

el riesgo de lesiones, el usuario debe leer

y comprender el manual del operador

antes de usar este producto.

AVERTISSEMENT :

Pour

réduire les risques de blessures,

l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation avant

d’employer ce produit.

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

TABLE OF CONTENTS

****************

 General Safety Rules .......................2-3

 Miter Saw Specific Safety Rules .....3-4

 Additional Safety Rules ...................4-5

 Symbols ..............................................6

 Electrical ............................................. 7

 Glossary of Terms ..............................8

 Features .........................................9-11

 Tools Needed ...................................12

 Loose Parts List ................................12

 Assembly .....................................13-20

 Operation .....................................21-31

 Adjustments .....................................32

 Maintenance ................................33-34

 Parts Ordering/Service ........Back page

TABLE DES MATIÈRES

****************

 Règles de sécurité générales ..........2-3

 Règles de sécurité du scie

à onlgets .........................................3-4

 Règles de sécurité suplémentaires ..4-5

 Symboles ............................................6

 Caractéristiques électriques ...............7

 Glossaire ............................................8

 Caractéristiques ............................9-11

 Outils nécessaires ...........................12

 Pièces détachées .............................12

 Assemblage .................................13-20

 Utilisation .....................................21-32

 Réglages ...........................................33

 Entretien ......................................34-35

 Commande de pièces/

réparation ..........................páge arrière

ÍNDICE DE CONTENIDO

****************

Reglas de seguridad generales .......2-3

Reglas de seguridad sierra

ingleteadora ....................................3-4

Advertencias de seguridad

adicionales ......................................4-5

Símbolos ............................................6

Aspectos eléctricos ............................ 7

Glosario de términos ..........................8

Características ..............................9-11

Herramientas necesarias ..................12

Lista de piezas sueltas .....................12

Armado ........................................13-20

Funcionamiento ...........................21-32

Ajustes ..............................................33

Mantenimiento .............................34-35

Pedidos de piezas/

servicio .......................... pág. posterior

2 − English

WARNING:

Read all safety warnings, instructions, illustrations and

specifications provided with this power tool. Failure to

follow all instructions listed below may result in electric

shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

power tool.

WORK AREA SAFETY

Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces,

such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body

is earthed or grounded.

Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of a GFCI reduces the risk

of electric shock.

PERSONAL SAFETY

Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the influence

of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal

injury.

GENERAL SAFETY RULES

Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or

energising power tools that have the switch on invites

accidents.

Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to

a rotating part of the power tool may result in personal

injury.

Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpected situations.

Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

Do not let familiarity gained from frequent use of tools

allow you to become complacent and ignore tool

safety principles. A careless action can cause severe

injury within a fraction of a second.

POWER TOOL USE AND CARE

Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from the

power tool before making any adjustments, changing

accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool

accidentally.

Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

3 − English

GENERAL SAFETY RULES

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused

by poorly maintained power tools.

Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

SERVICE

Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

MITER SAW SPECIFIC SAFETY RULES

Miter saws are intended to cut wood or wood-like

products, they cannot be used with abrasive cut-off

wheels for cutting ferrous material such as bars, rods,

studs, etc. Abrasive dust causes moving parts such as

the lower guard to jam. Sparks from abrasive cutting will

burn the lower guard, the kerf insert and other plastic

parts.

Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand, you

must always keep your hand at least 100 mm from

either side of the saw blade. Do not use this saw to

cut pieces that are too small to be securely clamped

or held by hand. If your hand is placed too close to the

saw blade, there is an increased risk of injury from blade

contact.

The workpiece must be stationary and clamped or

held against both the fence and the table. Do not feed

the workpiece into the blade or cut ”freehand” in any

way. Unrestrained or moving workpieces could be thrown

at high speeds, causing injury.

Push the saw through the workpiece. Do not pull the

saw through the workpiece. To make a cut, raise the

saw head and pull it out over the workpiece without

cutting, start the motor, press the saw head down and

push the saw through the workpiece. Cutting on the

pull stroke is likely to cause the saw blade to climb on top

of the workpiece and violently throw the blade assembly

towards the operator.

Never cross your hand over the intended line of cutting

either in front or behind the saw blade. Supporting the

workpiece ”cross handed” i.e. holding the workpiece to

the right of the saw blade with your left hand or vice versa

is very dangerous.

Do not reach behind the fence with either hand closer

than 100 mm from either side of the saw blade, to

remove wood scraps, or for any other reason while

the blade is spinning. The proximity of the spinning saw

blade to your hand may not be obvious and you may be

seriously injured.

Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with the

outside bowed face toward the fence. Always make

certain that there is no gap between the workpiece,

fence and table along the line of the cut. Bent or warped

workpieces can twist or shift and may cause binding on

the spinning saw blade while cutting. There should be no

nails or foreign objects in the workpiece.

Do not use the saw until the table is clear of all tools,

wood scraps, etc., except for the workpiece. Small

debris or loose pieces of wood or other objects that

contact the revolving blade can be thrown with high

speed.

Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced

and may bind on the blade or shift during cutting.

Ensure the miter saw is mounted or placed on a

level, firm work surface before use. A level and firm

work surface reduces the risk of the miter saw becoming

unstable.

Plan your work. Every time you change the bevel or

miter angle setting, make sure the adjustable fence

is set correctly to support the workpiece and will

not interfere with the blade or the guarding system.

Without turning the tool ”ON” and with no workpiece

on the table, move the saw blade through a complete

simulated cut to assure there will be no interference or

danger of cutting the fence.

Provide adequate support such as table extensions,

saw horses, etc. for a workpiece that is wider or longer

than the table top. Workpieces longer or wider than the

miter saw table can tip if not securely supported. If the

cut-off piece or workpiece tips, it can lift the lower guard

or be thrown by the spinning blade.

4 − English

MITER SAW SPECIFIC SAFETY RULES

Do not use another person as a substitute for a table

extension or as additional support. Unstable support

for the workpiece can cause the blade to bind or the

workpiece to shift during the cutting operation pulling

you and the helper into the spinning blade.

The cut-off piece must not be jammed or pressed by

any means against the spinning saw blade. If confined,

i.e. using length stops, the cut-off piece could get wedged

against the blade and thrown violently.

Always use a clamp or a fixture designed to properly

support round material such as rods or tubing. Rods

have a tendency to roll while being cut, causing the blade

to bite and pull the work with your hand into the blade.

Let the blade reach full speed before contacting the

workpiece. This will reduce the risk of the workpiece

being thrown.

If the workpiece or blade becomes jammed, turn

the miter saw off. Wait for all moving parts to stop

and disconnect the plug from the power source and/

or remove the battery pack. Then work to free the

jammed material. Continued sawing with a jammed

workpiece could cause loss of control or damage to the

miter saw.

After finishing the cut, release the switch, hold the

saw head down and wait for the blade to stop before

removing the cut-off piece. Reaching with your hand

near the coasting blade is dangerous.

Hold the handle firmly when making an incomplete cut

or when releasing the switch before the saw head is

completely in the down position. The braking action of

the saw may to be suddenly pulled downward, causing

a risk of injury.

 Save these instructions. Refer to them frequently and

use to instruct other users. If you loan someone this tool,

loan them these instructions also.

ADDITIONAL SAFETY RULES

 Use the proper extension cord. Make sure your extension

cord is in good condition. Use only a cord heavy enough

to carry the current your product will draw. An undersized

cord will cause a drop in line voltage resulting in loss of

power and overheating. A wire gauge size (A.W.G.) of at

least 14 is recommended for an extension cord 25 feet

or less in length. If in doubt, use the next heavier gauge.

The smaller the gauge number, the heavier the cord.

 Inspect tool cords periodically. If damaged, have

repaired by a qualified service technician at an authorized

service facility. Repair or replace a damaged or worn cord

immediately. Stay constantly aware of cord location and

keep it well away from the rotating blade.

 Inspect extension cords periodically and replace if

damaged.

 Polarized plugs. To reduce the risk of electric shock,

this tool has a polarized plug (one blade is wider than the

other). This plug will fit in a polarized outlet only one way.

If the plug does not fit fully in the outlet, reverse the plug.

If it still does not fit, contact a qualified electrician to install

the proper outlet. Do not change the plug in any way.

 Know your power tool. Read the operator’s manual

carefully. Learn the applications and limitations as well

as the specific potential hazards related to this tool.

 Always wear eye protection with side shields which

is marked to comply with ansi Z87.1 when using this

product. Failure to do so could result in objects being

thrown into your eyes, resulting in possible serious injury.

 Never stand on tool. Serious injury could occur if the tool

is tipped or if the cutting tool is unintentionally contacted.

 Keep guards in place and in good working order.

 Use the right direction of feed. Feed work into a blade,

cutter, or sanding spindle against the direction of rotation

of the blade, cutter, or sanding spindle only.

 Never leave tool running unattended. Turn the power

off. Don’t leave tool until it comes to a complete stop.

 Use only correct blades. Do not use blades with

incorrect size holes. Never use blade washers or blade

bolts that are defective or incorrect. The maximum blade

capacity of your saw is 7-1/4 in.

 Before making a cut, be sure all adjustments are

secure.

 Never touch blade or other moving parts during use.

 Double check all setups. Make sure blade is tight

and not making contact with saw or workpiece before

connecting to power supply.

 Firmly clamp or bolt your tool to a workbench or table

at approximately hip height.

 Make sure the miter table and saw arm (bevel function)

are locked in position before operating your saw. Lock

the miter table by pushing the miter lock lever down. Lock

the saw arm (bevel function) by securely tightening the

bevel lock knob.

5 − English

ADDITIONAL SAFETY RULES

 Never move the workpiece or make adjustment to any

cutting angle while the saw is running and the blade

is rotating. Any slip can result in contact with the blade

causing serious personal injury.

 Avoid awkward operations and hand positions where a

sudden slip could cause your hand to move into the blade.

ALWAYS make sure you have good balance. NEVER

operate your miter saw on the floor or in a crouched

position.

 Never stand or have any part of the body in line with the

path of the saw blade.

 Do not turn the motor switch on and off rapidly. This

could cause the saw blade to loosen and could create

a hazard. Should this ever occur, stand clear and allow

the saw blade to come to a complete stop. Disconnect

your saw from the power supply and securely retighten

the blade bolt.

 If any part of this miter saw is missing or should

break, bend, or fail in any way, or should any electrical

component fail to perform properly, shut off the power

switch, remove the miter saw plug from the power source

and have damaged, missing, or failed parts replaced

before resuming operation.

 Always turn off the saw before disconnecting it to avoid

accidental starting when reconnecting to power supply.

NEVER leave the saw unattended while connected to a

power source.

 This tool should have the following markings:

• To reduce the risk of injury, user must read the operator’s

manual.

• Wear eye protection.

• Keep hands and body out of the path of the saw blade.

Contact with the blade will result in serious injury.

• Check guarding system to make sure it is functioning

correctly.

• Do not perform any operation freehand.

• Never reach around the saw blade.

• Turn off tool and wait for saw blade to stop before

moving workpiece or changing settings.

• Disconnect the saw from the power source before

changing blade or servicing.

 Always carry the tool only by the carrying handle.

 This saw can tip over if the saw head is released

suddenly and the saw is not secured to a work surface.

ALWAYS secure this saw to a stable work surface before

any use to avoid serious personal injury.

 Always make sure the saw blade has clearance of all

obstructions before turning the saw on.

6 − English

SYMBOLS

Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation

of these symbols will allow you to operate the tool better and safer.

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye Protection

Always wear eye protection with side shields marked to comply

with ANSI Z87.1.

No Hands Symbol

Failure to keep your hands away from the blade will result in

serious personal injury.

Extremely Bright Light

This product uses extremely bright LEDs. To avoid serious eye

injury, do not stare into the light (not even from a distance).

Wet Conditions Alert Do not expose to rain or use in damp locations.

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

min Minutes Time

Alternating Current Type of current

n

o

No Load Speed Rotational speed, at no load

Class II Construction Double-insulated construction

.../min Per Minute Revolutions, strokes, surface speed, orbits, etc., per minute

SYMBOL NAME

DESIGNATION/EXPLANATION

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or

serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

CAUTION:

Indicates a hazardous situation, that, if not avoided, may result in minor or

moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates information considered important, but

not related to a potential injury (e.g. messages relating to property damage).

7 − English

ELECTRICAL

DOUBLE INSULATION

Double insulation is a concept in safety in electric power tools,

which eliminates the need for the usual three-wire grounded

power cord. All exposed metal parts are isolated from the

internal metal motor components with protecting insulation.

Double insulated tools do not need to be grounded.

WARNING:

The double insulated system is intended to protect the

user from shock resulting from a break in the tool’s internal

wiring. Observe all normal safety precautions to avoid

electrical shock.

NOTE: Servicing of a product with double insulation requires

extreme care and knowledge of the system and should

be performed only by a qualified service technician. For

service, we suggest you return the tool to your nearest

authorized service center for repair. Always use original

factory replacement parts when servicing.

ELECTRICAL CONNECTION

This tool has a precision-built electric motor. It should be

connected to a power supply that is 120 V, AC only (normal

household current), 60 Hz. Do not operate this tool on

direct current (DC). A substantial voltage drop will cause a

loss of power and the motor will overheat. If the tool does

not operate when plugged into an outlet, double check the

power supply.

EXTENSION CORDS

When using a power tool at a considerable distance from

a power source, be sure to use an extension cord that has

the capacity to handle the current the product will draw. An

undersized cord will cause a drop in line voltage, resulting in

overheating and loss of power. Use the chart to determine

the minimum wire size required in an extension cord. Only

round jacketed cords listed by Underwriter’s Laboratories

(UL) should be used.

When working outdoors with a product, use an extension

cord that is designed for outside use. This type of cord is

designated with “WA” or “W” on the cord’s jacket.

Before using any extension cord, inspect it for loose or

exposed wires and cut or worn insulation.

**Ampere rating (on product data plate)

0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0

Cord Length Wire Size (A.W.G.)

25’ 16 16 16 16 14 14

50’ 16 16 16 14 14 12

100’ 16 16 14 12 10 —

**Used on 12 gauge - 20 amp circuit.

NOTE: AWG = American Wire Gauge

WARNING:

Keep the extension cord clear of the working area.

Position the cord so that it will not get caught on lumber,

tools, or other obstructions while you are working with a

power tool. Failure to do so can result in serious personal

injury.

WARNING:

Check extension cords before each use. If damaged

replace immediately. Never use tool with a damaged cord

since touching the damaged area could cause electrical

shock resulting in serious injury.

8 − English

GLOSSARY OF TERMS

Pilot Hole (drill presses and scroll saws)

A small hole drilled in a workpiece that serves as a guide

for drilling large holes accurately or for insertion of a scroll

saw blade.

Push Blocks (jointer planers)

Device used to feed the workpiece over the jointer planer

cutterhead during any operation. This aid helps keep the

operator’s hands well away from the cutterhead.

Push Blocks and Push Sticks (table saws)

Devices used to feed the workpiece through the saw blade

during cutting operations. When making a narrow rip cut

without a jig or similar cutting aid, always use a push stick (not

a push block). A push block can be used for narrow ripping

operations, if a jig or similar cutting aid is used. These aids

help keep the operator’s hands well away from the blade.

Rabbet

A non-through cut positioned on the end or edge of the

workpiece which produces a square, two-sided notch or

trough in the workpiece.

Resaw (table saws and band saws)

A cutting operation to reduce the thickness of the workpiece

to make thinner pieces.

Resin

A sticky, sap-based substance that has hardened.

Revolutions Per Minute (RPM)

The number of turns completed by a spinning object in one

minute.

Ripping or Rip Cut (table saws)

A cutting operation along the length of the workpiece and

typically in the direction of the grain.

Riving Knife/Spreader/Splitter (table saws)

A metal piece, slightly thinner than the blade, which helps

keep the kerf open and also helps to prevent kickback.

Saw Blade Path

The area over, under, behind, or in front of the blade. As it

applies to the workpiece, that area which will be or has been

cut by the blade.

Snipe (planers)

Depression made at either end of a workpiece by cutter

blades when the workpiece is not properly supported.

Taper Cut

A cut where the material being cut has a different width at

the beginning of the cut from the end.

Through Sawing

Any cutting operation where the blade extends completely

through the thickness of the workpiece. This type of cut will

separate a single workpiece into two pieces.

Workpiece or Material

The item on which the operation is being done.

Worktable

Surface where the workpiece rests while performing a cutting,

drilling, planing, or sanding operation.

Anti-Kickback Pawls (radial arm and table saws)

A device which, when properly installed and maintained,

is designed to stop the workpiece from being kicked back

toward the front of the saw during a ripping operation.

Arbor

The shaft on which a blade or cutting tool is mounted.

Bevel Cut

A cutting operation made with the blade at any angle other

than 90° to the table surface.

Chamfer

A cut removing a wedge from a block so the end (or part of

the end) is angled rather than at 90°.

Compound Cut

A cross cut made with both a miter and a bevel angle.

Cross Cut

A cutting or shaping operation made across the grain or the

width of the workpiece.

Cutter Head (planers and jointer planers)

A rotating cutterhead with adjustable blades or knives. The

blades or knives remove material from the workpiece.

Dado Cut (table saws and compound sliding miter saws)

A non-through cut which produces a square, three-sided

notch or trough in the workpiece.

Featherboard (table saws)

A device used to help control the workpiece by guiding

it securely against the table or fence during any ripping

operation.

FPM or SPM

Feet per minute (or strokes per minute), used in reference

to blade movement.

Freehand

Performing a cut without the workpiece being guided by a

fence, miter fence, or other aids.

Gum

A sticky, sap-based residue from wood products.

Heel

Alignment of the blade to the miter gauge groove.

Kerf

The material removed by the blade in a through cut or the

slot produced by the blade in a non-through or partial cut.

Kickback

A hazard that can occur when the blade binds or stalls,

throwing the workpiece in the direction of the spinning blade.

Miter Cut

A cutting operation made with the workpiece at any angle

to the blade other than 90°.

Non-Through Cuts (table saws and compound sliding

miter saws)

Any cutting operation where the blade does not extend

completely through the thickness of the workpiece. This is a

cut where the blade will not cut the workpiece into two pieces.

9 − English

45

30

15

0

FEATURES

PRODUCT SPECIFICATIONS

Arbor Hole ............................................................... 5/8 in.

Blade Diameter .....................................................7-1/4 in.

No Load Speed ..................................... 5,350/min. (RPM)

Input ...............................120 V, AC only, 60 Hz, 10 Amps

Cutting Capacity with Miter at 0°/Bevel 0°:

Maximum nominal lumber sizes ................... 2 in. x 10 in.

Cutting Capacity with Miter at 45°/Bevel 0°:

Maximum nominal lumber sizes ..................... 2 in. x 6 in.

Cutting Capacity with Miter at 0°/Bevel 45°:

Maximum nominal lumber sizes ................... 2 in. x 10 in.

Cutting Capacity with Miter at 45°/Bevel 45°:

Maximum nominal lumber sizes ..................... 2 in. x 6 in.

Fig. 1

LOCK

SWITCH

TRIGGER

DUST BAG

MITER

FENCE

BASE

WORK

CLAMP

MITER

TABLE

CONTROL

ARM

MITER

LOCK HANDLE

“NO HANDS

ZONE” LABEL

“NO HANDS ZONE”

BOUNDARY LINE

MITER

SCALE

UPPER

BLADE

GUARD

LOWER BLADE

GUARD

“D”

HANDLE

SLIDE

LOCK KNOB

SLIDE BAR

DEPTH STOP

DEPTH

CONTROL KNOB

SUPPORT FOOT

DETENT

RELEASE LEVER

BLADE

WRENCH

THROAT

PLATE

LED

LIGHT

LED

SWITCH

CROWN

INDICATOR

CORD

CLIP

BEVEL

LOCK KNOB

BEVEL

SCALE

PIVOT

ASSEMBLY INDICATOR

POSITIVE

STOP(S)

TRIGGER

LOCKOUT LEVER

PARTIAL

SLIDING

FENCE

SIDE

HANDLE

SIDE

HANDLE

10 − English

45

30

15

0

FEATURES

KNOW YOUR COMPOUND MITER SAW

See Figure 1.

The safe use of this product requires an understanding of the

information on the tool and in this operator’s manual as well

as a knowledge of the project you are attempting. Before use

of this product, familiarize yourself with all operating features

and safety rules.

7-1/4 in. BLADE

A 7-1/4 in. blade is included with the compound miter saw. It will

cut nominal materials up to 2 in. thick by 10 in. wide, depending

upon the angle at which the cut is being made.

BLADE WRENCH STORAGE

See Figure 1.

A blade wrench is packed with the saw. One end of the wrench

is a phillips screwdriver and the other end is a hex key. Use the

hex key end when installing or removing blade and the phillips

end when removing or loosening screws. A storage area for the

blade wrench is located in the saw’s base.

BEVEL LOCK KNOB

See Figure 2.

The bevel lock knob securely locks your compound miter saw

at desired bevel angles. A positive stop adjustment screw has

been provided on each side of the saw arm. These adjustment

screws are for making fine adjustments at 0° and 45°.

CARRYING HANDLES

See Figure 2.

For convenience when carrying or transporting the miter saw

from one place to another, a carrying handle has been provided

on top of the saw arm, along with handles on either side of the

base. To transport, turn off and unplug the saw, then lower the

saw arm and lock it in the down position by depressing the lock

pin towards the saw housing.

NOTE: DO NOT perform any cutting operation with the saw in

the locked position.

CROWN INDICATOR

See Figure 1.

For use with the auxiliary fence. To cut crown molding nested

against the auxiliary fence in the upright position, align the arrow

on the crown indicator with the arrow on the pivot assembly

and tighten the slide lock knob securely.

DETENT OVERRIDE

See Figure 3.

The detent override allows the miter table to move freely to any

desired angle. With the miter lock handle loosened and the detent

release lever squeezed (1), pull the detent override up (2) and

release the detent release lever (3) to bypass the positive stops

on the miter scale. To release the detent override and allow the

miter table to engage the positive stops, squeeze and release

the detent release lever.

ELECTRIC BRAKE

An electric brake has been provided to quickly stop blade

rotation after the switch is released.

SAW ARM LOCKED IN DOWN POSITION

LOCK

CARRYING

HANDLE

“D”

HANDLE

MITER

LOCK HANDLE

BEVEL

LOCK KNOB

LED

SWITCH

Fig. 2

Fig. 3

1

3

2

DETENT

RELEASE LEVER

DETENT

OVERRIDE

SIDE

HANDLE

11 − English

FEATURES

LED LIGHTING SYSTEM

The LED casts a shadow of the blade teeth onto the workpiece for

making precision cuts and predicts blade kerf for blade cut line.

MITER FENCE

The miter fence on the compound miter saw has been provided

to hold your workpiece securely against when making all cuts.

The right side is larger, providing additional support.

MITER LOCK HANDLE

See Figure 3.

The miter lock handle securely locks the saw at desired miter

angles. Tighten the handle to lock the saw in place. To release

the saw, loosen the handle and squeeze the detent release lever.

MITER SCALE

The miter scale can be set from 0° to 47° (both left and right)

to achieve a wide variety of cuts.

PARTIAL SLIDING FENCE

The partial sliding fence on your compound miter saw has

been provided to help secure the workpiece when making

straight cuts.

The sliding feature makes it easy to adjust the position of the

partial fence. Loosen the fence screw before attempting to

slide the partial fence. Once the desired position is determined,

tighten the fence screw to secure.

POSITIVE STOPS ON MITER TABLE

Positive stops have been provided at 0°, 15°, 22.5°, 31.6°, and

45° on both the left and right side of the miter table.

NOTE: To bypass the positive stops, squeeze the detent release

lever and lift the detent override. To release the override, squeeze

the detent release lever.

SELF-RETRACTING LOWER BLADE GUARD

The lower blade guard is made of shock-resistant, see-through

plastic that provides protection from each side of the blade. It

retracts over the upper blade guard as the saw is lowered into

the workpiece.

SLIDE BARS

When unlocked, the saw arm will glide forward and backward

the length of the slide bars for cutting various workpiece widths.

SLIDE LOCK KNOB

The slide lock knob locks and unlocks the sliding feature of

this tool.

SPINDLE LOCK BUTTON

See Figure 4.

The spindle lock button locks the spindle and stops the blade

from rotating. Depress and hold the lock button while installing,

changing, or removing blade.

Fig. 4

PADLOCK

SWITCH

TRIGGER

SWITCH

TRIGGER

SWITCH TRIGGER

See Figure 4.

The saw will not start until you depress the trigger lockout

lever and squeeze the switch trigger. To prevent unauthorized

use of the compound miter saw, disconnect it from the power

supply and lock the switch in the off position. To lock the switch,

install a padlock (not included) through the hole in the switch

trigger and make certain the switch is inoperable. If the switch

is still operable with the padlock installed, a padlock with a

larger shackle diameter must be used. Store the padlock key

in another location.

PADLOCK

HOLE

TRIGGER

LOCKOUT LEVER

SPINDLE

LOCK BUTTON

12 − English

BLADE

WRENCH

LOOSE PARTS LIST

Fig. 6

 Work Clamp

 Side Handles (2) with screws

 Dust Bag

 Blade Wrench

WORK CLAMP

DUST BAG

The following items are included with the tool:

WARNING:

The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.

The following tools (not included) are needed for making adjustments or installing the blade:

TOOLS NEEDED

Fig. 5

COMBINATION

SQUARE

SIDE

HANDLE

SIDE

HANDLE

 Operator’s Manual (not shown)

13 − English

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully lift saw from the carton by the carrying handle and

the saw base, and place it on a level work surface.

WARNING:

Do not use this product if any parts on the Loose Parts List

are already assembled to your product when you unpack it.

Parts on this list are not assembled to the product by the

manufacturer and require customer installation. Use of a

product that may have been improperly assembled could

result in serious personal injury.

 This saw has been shipped with the saw arm secured in the

down position. To release the saw arm, push down on the “D”

handle, cut the tie-wrap, and pull out on the lock pin.

WARNING:

The saw arm is spring loaded. Hold the handle down to

prevent from snapping up when cutting the tie-wrap. Failure

to do so could result in possible serious injury.

 Lift the saw arm by the “D” handle. Hand pressure should

remain on the saw arm to prevent sudden rise upon

release of the tie wrap.

 Cut the tie wrap at the end of the slide bar. Slide the saw

head to its most rearward position and tighten the slide lock

knob securely.

 Inspect the tool carefully to make sure no breakage or

damage occurred during shipping.

 Do not discard the packing material until you have carefully

inspected and satisfactorily operated the product.

 The saw is factory set for accurate cutting. After assembling

it, check for accuracy. If shipping has influenced the settings,

refer to specific procedures explained in this manual.

 If any parts are damaged or missing, please call

1-800-525-2579 for assistance.

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product with

damaged or missing parts could result in serious personal

injury.

WARNING:

Do not attempt to modify this product or create accessories

not recommended for use with this tool. Any such alteration

or modification is misuse and could result in a hazardous

condition leading to possible serious personal injury.

WARNING:

Do not connect to power supply until assembly is complete.

Failure to comply could result in accidental starting and

possible serious personal injury.

WARNING:

Do not start the compound miter saw without checking

for interference between the blade and the miter fence.

Serious personal injury or damage to the blade could result

if it strikes the miter fence during operation of the saw.

WARNING:

This saw can tip over if the saw head is released suddenly

and the saw is not secured to a work surface. ALWAYS

secure this saw to a stable work surface before any use to

avoid serious personal injury.

TRACE HOLES

AT THESE LOCATIONS

FOR HOLE PATTERN

Fig. 7

MOUNTING

SURFACE

SAW BASE

TRACE HOLES

AT THESE LOCATIONS

FOR HOLE PATTERN

14 − English

45

30

15

0

Fig. 9

ASSEMBLY

MOUNTING HOLES

See Figure 7.

WARNING:

Before starting any cutting operation, clamp or bolt your

miter saw to a workbench or an approved miter saw stand.

If a miter saw stand is used, read operator’s manual and

follow the instructions for the miter saw stand. Never

operate your miter saw on the floor or in a crouched

position. Failure to heed this warning can result in serious

personal injury.

The compound miter saw should be mounted to a firm

supporting surface such as a workbench, mounting board,

or miter saw stand. The saw base has four mounting

holes. If using bolts, they should be of sufficient length to

accommodate the saw base, lock washers, hex nuts, and

the thickness of the workbench or other mounting surface.

Tighten all bolts or screws securely.

The hole pattern for mounting to a workbench is shown in

figure 7. Carefully check the workbench after mounting to

make sure that no movement can occur during use. If any

tipping, sliding, or walking is noted, secure the workbench

to the floor before operating.

USING THE DEPTH STOP

See Figure 8.

When used, the depth stop limits the downward travel of

the blade when cutting dadoes and other non-through cuts.

To use the depth stop:

 Unplug the saw.

 If the saw is in storage or transport position, unlock the

saw arm.

 Rotate the depth stop away from the motor housing.

 With the end of the depth control knob touching the depth

stop, adjust the depth control knob by turning the knob

until the desired depth of cut is attained.

 A wooden spacer of at least 2-1/2 inches must be placed

between the workpiece and the fence for a consistent

depth of cut in the workpiece. Use the work clamp to

clamp the spacer and another suitable clamp to clamp

the workpiece. Make the slide cut at the desired depth.

See Figures 33 - 34.

 Rotate the depth stop back towards the motor housing

for normal through cuts.

NOTE: The depth stop must be moved toward the motor

housing before locking/unlocking the saw arm.

LOCKING/UNLOCKING THE SAW ARM

See Figure 9.

When locking and unlocking the saw arm, it is not necessary

to loosen the depth control knob.

LOCK

“D”

HANDLE

To unlock and raise the saw arm:

 Firmly grasp the “D” handle and apply downward pres-

sure while at the same time pulling the lock pin out and

away from the saw housing.

 Release the lock pin and slowly raise the saw arm.

To lock the saw arm:

 Firmly grasp the “D” handle and apply downward pres-

sure while at the same time pushing the lock pin in and

toward the saw housing.

 Release the lock pin allowing it to lock the saw into place.

Fig. 8

DEPTH

CONTROL KNOB

DEPTH STOP

15 − English

45

30

15

0

ASSEMBLY

DUST BAG

See Figure 10.

A dust bag is provided for use on this miter saw. It fits over

the exhaust port on the back of the saw.

NOTE: The exhaust port also accepts 1-1/4 in. vacuum hose.

BLADE WRENCH

See Figure 10.

A blade wrench is included with this saw. One end of the

wrench is a phillips screwdriver and the other end is a hex

key. Use the hex key end when installing or removing blade

and the phillips end when removing or loosening screws. A

storage area for the blade wrench is located on the back of

the left miter fence.

WORK CLAMP

See Figure 11.

WARNING:

In some operations, the work clamp assembly may

interfere with the operation of the blade guard assembly.

Always make sure there is no interference with the blade

guard prior to beginning any cutting operation to reduce

the risk of serious personal injury.

The work clamp provides greater control by clamping the

workpiece to the fence or the saw table. It also prevents

the workpiece from creeping toward the saw blade. This is

very helpful when cutting compound miters. Depending on

the cutting operation and the size of the workpiece, it may

be necessary to use a C-clamp or other suitable clamp

instead of the work clamp to secure the workpiece prior to

making the cut.

To install the work clamp:

 Place the work clamp shaft in one of the holes located

behind the miter fence.

 Rotate the work clamp knob to move it up or down as

needed to secure the workpiece.

Fig. 11

BASE

WORK

CLAMP

Fig. 10

DUST

BAG

EXHAUST

PORT

WORK

CLAMP KNOB

BLADE

WRENCH

16 − English

45

30

15

0

SIDE HANDLES

See Figures 12 - 13.

Side handles have been provided for both the left and the

right side of the saw.

To install side handles:

 Align the holes in one of the side handles with the holes

in the saw base.

 Insert the provided hex screws into the holes and tighten

securely using the blade wrench provided.

 Repeat for other side handle.

Fig. 13

Fig. 12

HEX SCREW

SIDE

HANDLE

SIDE

HANDLE

BASE

ASSEMBLY

HEX SCREW

17 − English

ASSEMBLY

TO INSTALL/REPLACE THE BLADE

See Figures 14 - 15.

The blade is shipped installed on this miter saw model.

Instructions have been included for reference when changing

or replacing blades.

WARNING:

A 7-1/4 in. blade is the maximum blade capacity of the

saw. Never use a blade that is too thick to allow outer

blade washer to engage with the flats on the spindle. Larger

blades will come in contact with the blade guards, while

thicker blades will prevent the blade bolt from securing the

blade on the spindle. Either of these situations could result

in a serious accident and can cause serious personal injury.

 Unplug the saw.

 Raise the saw arm.

 Rotate lower blade guard up and back to expose the

blade bolt.

 Depress the spindle lock button and rotate the blade bolt

until the spindle locks.

 Using the blade wrench provided, loosen and remove the

blade bolt.

NOTE: The blade bolt has left hand threads. Turn blade

bolt clockwise to loosen.

 Remove the outer blade washer.

NOTE: The inner blade washer is integrated into the

spindle and cannot be removed.

 Wipe a drop of oil onto inner blade washer and outer

blade washer where they contact the blade.

 Fit saw blade inside lower blade guard and onto spindle.

The blade teeth point downward at the front of saw as

shown in figure 15.

 Replace the outer blade washer. Double “D” flats on blade

washers align with flats on spindle.

 Depress spindle lock button and replace blade bolt.

NOTE: The blade bolt has left hand threads. Turn blade bolt

counterclockwise to tighten.

CAUTION:

Always install the blade with the blade teeth and the arrow

printed on the side of the blade pointing down at the front

of the saw. The direction of blade rotation is also stamped

with an arrow on the upper blade guard.

 Tighten blade bolt securely.

 Lower the blade guard.

 Raise and lower the saw arm to ensure upper blade guard

functions correctly.

WARNING:

Make sure the spindle lock button is not engaged before

reconnecting saw into power source. Never engage

spindle lock button when blade is rotating.

LOWER BLADE

GUARD

OUTER BLADE

WASHER

WITH DOUBLE

“D” FLATS

BLADE

BOLT

FLAT(S)

ON SPINDLE

BLADE

BOLT

OUTER

BLADE

WASHER

BLADE

TO

LOOSEN

TO

TIGHTEN

BLADE

Fig. 14

Fig. 15

SPINDLE

LOCK BUTTON

SPINDLE

18 − English

45

30

15

0

ASSEMBLY

REMOVING/REPLACING THE THROAT PLATE

See Figure 16.

WARNING:

The throat plate must be below the miter table. If the throat

plate is too high or too low, the workpiece can catch on

the uneven edges resulting in binding which could result

in serious personal injury.

Never operate the saw without a throat plate installed.

To remove/replace:

 Unplug the saw.

 Remove the screws securing the throat plate.

 Lift the throat plate from the saw.

 To reinstall the throat plate, align the holes in the throat

plate with the holes in the saw base.

 Retighten the screws, being careful not to overtighten

which can cause the throat plate to bow or bend.

ADJUSTING SUPPORT FOOT

See Figure 16.

Turn the support foot clockwise or counterclockwise depending

on the amount of support needed for making sliding cuts.

NOTE: Many of the illustrations in this manual show only

portions of the compound miter saw. This is intentional so that

we can clearly show points being made in the illustrations.

Never operate the saw without all guards securely in

place and in good operating condition.

SQUARING THE BLADE TO THE FENCE

See Figures 17 - 22.

 Unplug the saw.

 Pull the saw arm all the way down and engage the lock

pin to hold the saw arm in transport position.

 Loosen the miter lock handle approximately one-half turn

and squeeze the detent release lever.

 Rotate the miter table until the scale indicator is positioned

at 0°.

 Release the detent release lever, engaging the positive

stop notch, then tighten the miter lock knob to secure the

miter table.

 Tighten the miter lock knob to secure the miter table.

 Loosen bevel lock knob and set saw arm at 0° bevel (blade

set 90° to miter table). Tighten bevel lock knob.

 Lay a square flat on the miter table. Place one leg of the

square against the fence. Slide the other leg of the square

against the flat part of saw blade.

NOTE: Make sure that the square contacts the flat part of

the saw blade, not the blade teeth.

 The edge of the square and the saw blade should be

parallel as shown in figure 17.

THROAT

PLATE

Fig. 16

SUPPORT

FOOT

MITER

LOCK HANDLE

Fig. 17

MITER

TABLE

VIEW OF BLADE SQUARE WITH FENCE

SQUARE

MITER

FENCE

BLADE

19 − English

45

30

15

0

ASSEMBLY

 If the front or back edge of the saw blade angles away

from the square as shown in figures 18 - 19, adjustments

are needed.

 Loosen the fence screw and slide the partial sliding miter

fence toward the blade to access the socket head screws

securing the left miter fence to the table.

 Using the blade wrench provided, loosen the socket head

screws that secure the miter fence to the miter table.

 Rotate the miter fence left or right until the saw blade is

parallel with the square.

VIEW OF BLADE NOT SQUARE WITH

FENCE, ADJUSTMENTS ARE REQUIRED

Fig. 18

MITER

TABLE

SQUARE

MITER

FENCE

Fig. 19

Fig. 21

Fig. 22

VIEW OF BLADE NOT SQUARE WITH

FENCE, ADJUSTMENTS ARE REQUIRED

MITER

TABLE

SQUARE

MITER

FENCE

INDICATOR

SCREW

BEVEL

SCALE

INDICATOR

SCREW

MITER SCALE

BEVEL

LOCK KNOB

45

30

15

0

SCALE

INDICATOR

Fig. 20

SOCKET HEAD

SCREW(S)

SOCKET HEAD

SCREW(S)

BLADE

FENCE

SCREW

PARTIAL

SLIDING

MITER

FENCE

MITER

FENCE

20 − English

ASSEMBLY

 Retighten the screws securely and recheck the blade-to-

fence alignment.

 Return the partial sliding miter fence to the home position

and retighten the fence screw to secure.

Your saw has several scale indicators. After squaring

adjustments have been made, it may be necessary to loosen the

indicator screws and reset them to zero. See Figures 21 - 22.

SQUARING THE BLADE TO THE MITER TABLE

See Figures 23 - 25.

 Unplug the saw.

 Pull the saw arm all the way down and engage the lock

pin to hold the saw arm in transport position.

 Loosen the miter lock handle approximately one-half turn

and squeeze the detent release lever.

 Rotate the miter table until the scale indicator on the control

arm is positioned at 0°.

 Release the detent release lever, engaging the positive

stop notch, then tighten the miter lock knob to secure the

miter table.

 Loosen the bevel lock knob and set saw arm at 0° bevel

(blade set 90° to miter table). Tighten bevel lock knob.

 Place a combination square against the miter table and

the flat part of saw blade.

NOTE: Make sure that the square contacts the flat part of

the saw blade, not the blade teeth.

 Rotate the blade by hand and check the blade-to-table

alignment at several points.

 The edge of the square and the saw blade should be

parallel as shown in figure 23.

 If the top or bottom of the saw blade angles away from

the square as shown in figures 24 and 25, adjustments are

needed.

 Loosen bevel lock knob.

 Adjust positive stop adjustment screw to bring saw

blade into alignment with the square. See Positive Stop

Adjustment in the Adjustment section.

 Tighten bevel lock knob. Recheck blade-to-table alignment.

NOTE: The above procedure can be used to check blade

squareness of the saw blade to the miter table at both 0°

and 45° angles.

Your saw has several scale indicators. After squaring

adjustments have been made, it may be necessary to loosen the

indicator screws and reset them to zero. See Figures 21 - 22.

MITER

TABLE

COMBINATION

SQUARE

BLADE

MITER

FENCE

CORRECT VIEW OF BLADE

SQUARE WITH MITER TABLE

VIEW OF BLADE NOT SQUARE WITH MITER TABLE,

ADJUSTMENTS ARE REQUIRED

Fig. 24

VIEW OF BLADE NOT SQUARE WITH MITER TABLE,

ADJUSTMENTS ARE REQUIRED

MITER

TABLE

COMBINATION

SQUARE

BLADE

MITER

FENCE

MITER

TABLE

MITER

LOCK HANDLE

COMBINATION

SQUARE

BLADE

MITER

FENCE

Fig. 23

Fig. 25

La page charge ...

Ryobi TSS702 Le manuel du propriétaire

Ryobi TSS702 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents