Vantron ZB-HD-ANT-257 Manuel utilisateur
- Taper
- Manuel utilisateur
ZB-HD-ANT-257
Hardware User Manual
Product Version: 1.0
Date: 2021-12-14
For any question, please contact Chengdu Vantron Technology, Ltd.
Copyright © Vantron Technology, Ltd. All rights reserved.
Change History
This table describes the version and release date.
Rev. Date Description Author
1.0 2021-12-14 First release. Cong Yang
2.0 2022-01-07 Modify product parameter Cong Yang
Foreword
Copyright
While all information contained herein have been carefully checked to assure its
accuracy in technical details and printing, Vantron assumes no responsibility resulting
from any error or features of this manual, or from improper uses of this manual or the
software. Please contact our technical department for relevant operation solutions if
there is any problem that cannot be solved according to this manual.
Vantron reserves all rights of this manual, including the right to change the content,
form, product features, and specifications contained herein at any time without prior
written notice.
The trademarks and registered trademarks in this manual are properties of their
respective owners. No part of this manual may be copied, reproduced, translated or
sold. No changes or other purposes are permitted without the prior written consent of
Vantron.
Vantron reserves the right of all publicly-released copies of this manual.
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol Type Description
Notice Important information and regulations
Caution Caution for latent damage to system or
harm to personnel
Statement & Disclaimer
It is recommended to read and comply with this manual which provides important
guidance and helps decreasing the danger of injury, electric shock, fire, or any
damage to the device.
Vantron assumes no legal liability of accidents resulting from failure of conforming to
the safety instructions.
Limitation of Liability/Non-warranty
For direct or indirect damage to this device or other devices of Vantron caused by
failure of conforming to this manual or the safety instructions on device label, Vantron
assumes neither warranty nor legal liability even if the device is still under warranty.
The device should be installed, debugged and maintained by professionals.
The outside antennas are not permitted to be installed or to be changed by
non-professionals. To run the device normally, only specified antennas are approved
to be assembled together by professionals.
Unit shall be used with indoor-use antenna only. No antenna for this unit canbe
installed outdoor.
Safety Instructions
Keep and comply with all operation instructions, warnings, and information.
Pay attention to warnings on this device.
Read the following precautions so as to decrease the danger of injury, electric
shock, fire, or any damage to the device.
Operations and service instructions are provided with the equipment.
Unit shall be used with indoor-use antenna only. No antenna for this unit canbe
installed outdoor.
The maximum operation temperature is 85°C.
Precautions
Pay attention to the product labels/safety instructions printed on silk screens.
Do not try repairing this product unless declared in this manual.
Keep away from heat source, such as heater, heat dissipater, or engine casing.
Do not insert other items into the slot (if any) of this device.
Ensure ventilation of the ventilation slot.
System fault may arise if other items are inserted into this device.
Installation: ensure correct installation according to instructions from the
manufacturer with recommended installation tools.
Ensure ventilation and smoothness according to relevant ventilation standards.
Safety Instructions for Power Cables and Accessories
Use Proper power source only. Start only with power source that satisfies
voltage label and the voltage necessary according to this manual. Please contact
technical support personnel of Vantron for any uncertainty about the requirements of
necessary power source.
Use tested power source. This product still contains a button lithium batteryasa
real-time clock after its external power source is removed and therefore should not be
short-circuited during transportation or placed under high temperature.
Place cables properly: Do not place cables at any place with extrusion danger.
Cleaning Instructions
Please power off before cleaning the device.
Do not use spray detergent.
Clean with a damp cloth.
Do not try cleaning exposed electronic components unless with a dust collector.
Support for special fault: Power off and contact technical support personnel of
Vantron in case of the following faults:
The device is damaged.
The temperature is excessively high.
Fault is still not solved after operations according to the manual.
Contents
1INTRODUCTION
.......................................................................................................................................... 1
1.1 PRODUCT DESCRIPTION................................................................................................................................ 1
1.2 CONNECTOR DESCRIPTION........................................................................................................................... 1
2OVERVIEW
.................................................................................................................................................... 2
2.1 INTRODUCTION............................................................................................................................................ 2
2.2 SPECIFICATIONS............................................................................................................................................2
3 HARDWARE INSTRUCTIONS.....................................................................................................................3
3.1 APPEARANCE................................................................................................................................................3
3.2 INTERFACE DESCRIPTION...............................................................................................................................3
3.3 STRUCTURE.................................................................................................................................................. 3
4 HARDWARE FUNCTION DESCRIPTION...................................................................................................4
4.1 ANT+ MODULE...........................................................................................................................................4
5 HARDWARE OPERATION NOTE............................................................................................................... 5
5.1 POWER PREPARATION...................................................................................................................................5
5.1.1 Environment Preparation
...............................................................................................................
5
5.1.2 DC Power Input
...............................................................................................................................
5
5.2 ANTENNA.................................................................................................................................................... 5
6 SOFTWARE INSTRUCTIONS...................................................................................................................... 6
7TIPS
................................................................................................................................................................ 7
8STATEMENT
..................................................................................................................................................9
APPENDIX A: HOW TO CONTACT US............................................................................................................. 13
VT-PNL156-MT65-HD Hardware User Manual
1
1 Introduction
1.1 Product Description
Vantron offers both ARM and ATOM based Single Boards Computer (SBC) platforms
including Cirrus Logic EP9315, RockChip RK3128, RK3368, RK3288, RK3399,
Freescale iMX6, iMX8, TI OMAP35xx CortexA8 series, and Intel SkyLake and
ApolloLake processor boards. In additional to offering the standard SBCs,wealso
provide professional customization board design services. Our seamless project
management, efficient error-free development process, strong fundamentals in
technology, sufficient in human resources, and on-time delivery will guarantee the
success in your project development.
Based on idea of “Application Ready” products and services, our embedded
computers have embedded basic operation system which includes the driversofits
interfaces. So it is easy to be used by adding your application software only. It can
speed Time to Market of your products, and save more cost.
1.2 Connector Description
These tables respectively describe the valid signal of connectors on the Vantron
board.
Table 1-1 Term description (1)
N/C Not connect
GND Ground
/ Active low signal
+ Positive of difference signal
- negative of difference signal
Table 1-2 Term description (2)
I Input
O Output
I/O input/output
P Power or ground
A Analog
OD Open drain
CMOS 3.3 V CMOS
LVCMOS Low Voltage CMOS
LVTTL Low Voltage TTL
3.3V 3.3 V signal level
5V 5 V signal level
USB 5 V tolerant signal
PCIe PCI Express signal, not 3.3 V tolerant
NC No Connection
VT-PNL156-MT65-HD Hardware User Manual
2
2Overview
2.1 Introduction
ZB-HD-ANT-257 is ANT+ module.
2.2 Specifications
Table 2-1 Specifications
Specifications
SOC Processor TI CC2571
Interfaces
GPIO 3xGPIO
UART 1xUART
Wireless ANT+ 2.4-GHz Radio support RSSI
Power DC Input Support 3.3V/50mA 1.8V/1mA DC power supply.
Design
Dimensions 32.79 x 31.36 mm
Tablet Weight TBD
Environment
Condition
Temperature Operating: -40℃~85℃(Recommended: 25℃)
storage: -20 ~ +60℃(Recommended: 25℃)
Humidity 5-95%RH (Non-Condensation)
VT-PNL156-MT65-HD Hardware User Manual
3
3 Hardware Instructions
3.1 Appearance
Figure 3-1 Views
3.2 Interface Description
Figure 3-2 Interfaces (1)
3.3 Structure
Download the board structure document from Vantron official website:
www.vantrontech.com.cn
Figure 3-4 Structure
Unit: mm
VT-PNL156-MT65-HD Hardware User Manual
4
4 Hardware Function Description
This chapter mainly describes the main hardware functions of this product, including
ANT+.
4.1 ANT+ Module
ANT+ module shall support ANT+ communication at least 1 channel, and RSSI
(Received Signal Strength Indicator).
VT-PNL156-MT65-HD Hardware User Manual
5
5 Hardware Operation Note
This chapter provides a guide to set up and use some of the features of the tablet. For
more details, see hardware description.
5.1 Power Preparation
5.1.1 Environment Preparation
Before the device is powered on, please confirm whether the environmental
conditions meet the requirements. Environmental conditions are as follows:
●Operation Temperature: 0°C ~ +60°C
●Operation Humidity: 5-95%RH (Non-Condensation)
5.1.2 DC Power Input
Please confirm the power input is 3.3V, and the reference current is 50mA.
Do not use unauthorized or incompatible power adaptors to charge the device.
Otherwise fire, explosion or other incidents may be caused.
5.2 Antenna
The design of the internal antenna of ZB-HD-ANT-257 is shown in Figure 5-1.
Figure 5-1 Internal antenna
In order to ensure that the tablet functions can work properly, please do not cover the
antenna area with metal shielding devices.
VT-PNL156-MT65-HD Hardware User Manual
6
6 Software Instructions
ZB-HD-ANT-257 has been pre-loaded firmware. For more information, please refer to
software user manual for software operation.
VT-PNL156-MT65-HD Hardware User Manual
7
7Tips
Waste Disposal
It is recommended to disassemble the device before abandoning it in conformity with
local regulations. Please ensure that the abandoned batteries are disposed according
to local regulations on waste disposal. Do not throw batteries into fire (explosive) or
put in common waste canister. Products or product packages with the sign of
“explosive” should not be disposed like household waste but delivered to specialized
electrical & electronic waste recycling/disposal center. Proper disposal of this sort of
waste helps avoiding harm and adverse effect upon surroundings and people’s health.
Please contact local organizations or recycling/disposal center for more
recycling/disposal methods of related products.
Comply with the following safety tips:
Do not use in combustible and explosive environment
Keep away from combustible and explosive environment for fear of danger.
Keep away from all energized circuits.
Operators should not remove enclosure from the device. Only the group or person
with factory certification is permitted to open the enclosure to adjust and replace the
structure and components of the device. Do not change components unless the
power cord is removed. In some cases, the device may still have residual voltage
even if the power cord is removed. Therefore, it is a must to remove and fully
discharge the device before contact so as to avoid injury.
Unauthorized changes to this product or its components are prohibited.
In the aim of avoiding accidents as far as possible, it is not allowed to replace the
system or change components unless with permission and certification. Please
contact the technical department of Vantron or local branches for help.
Pay attention to caution signs.
VT-PNL156-MT65-HD Hardware User Manual
8
Caution signs in this manual remind of possible danger. Please comply with relevant
safety tips below each sign. Meanwhile, you should strictly conform to all safety tips
for operation environment.
Notice
Considering that reasonable efforts have been made to assure accuracy of this
manual, Vantron assumes no responsibility of possible missing contents and
information, errors in contents, citations, examples, and source programs.
Vantron reserves the right to make necessary changes to this manual withoutprior
notice. No part of this manual may be reprinted or publicly released in formsof
photocopy, tape, broadcast, e-document, etc.
VT-PNL156-MT65-HD Hardware User Manual
9
8 Statement
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the
user’s authority to operate the equipment.
NOTE: this equipment has been tested and found to comply with the limits for a Class B digital
device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against
harmful interference in a residential installation. This equipment generates uses and can radiate
radio
frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful
interference to radio communications. However, there is no guarantee that interference will not
occur in a
particular installation. If this equipment does cause harmful interferencetoradioortelevision
reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the
interference by one or more of the following measures:● Reorient of relocate the receiving
antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit difference from that to which the receiver is
connected.
● Consult the dealer or an experienced radio/TV technician for help
The final end product must be labeled in a visible area with the following “Contains FCC ID:
2AAGE-257"
If the FCC identification number is not visible when the module is installedinsideanotherdevice,
then the
outside of the device into which the module is installed must also display a label referring to the
enclosed
VT-PNL156-MT65-HD Hardware User Manual
10
module. This exterior label can use wording such as the following; Contains Transmitter Module
FCC ID:2AAGE-257.
According to FCC Part 15 Subpart C Section 15.212, the radio elements of the
modular transmitter must have radio frequency circuitry shielded. However, due to
there have no radio frequency circuitry shielded for this Module, this module is
granted as a Limited Modular Approval. When this I Module is installed into the end
product, a Class II Permissive Change or a New FCC ID submission is required to
ensure the full compliance of FCC relevant requirements.
remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
When the module is installed inside another device, the user manual of this device must contain
below
warning statements;
1. This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
1) this device may not cause harmful interference,
9/10
2) this device must accept any interference received, including interference that
may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance
could
void the user’s authority to operate the equipment. The devices must be installed and used in
strict accordance with the manufacturer’s instructions as described in the user documentation
that comes with the product.
Manual Information to the End User:
The OEM integrator has to be aware not provide information to the end user regarding how to
install or remove this RF module in the user’s manual of the end product which integrates this
module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
When the module is installed inside another device, the user manual of this device must contain
below warning statements;
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
this device may not cause harmful interference,
this device must accept any interference received, including interference that may
cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment. The devices must be installed and used in
VT-PNL156-MT65-HD Hardware User Manual
11
strict accordance with the manufacturer’s instructions as described in the user documentation that
comes with the product.
IC：
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Important Note:
In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the Canada authorization
is no longer considered valid and the IC cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end
product (including the transmitter) and obtaining a separate Canada authorization.
Note Importante:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre
émetteur), l'autorisation du Canada n'est plus considéré comme valide et l' IC ne peut
pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera
chargé de réévaluer le produit final (y compris l'émetteur) et l'obtentiond'une
autorisation distincte au Canada.
End Product Labeling
The final end product must be labeled in a visible area with the following: Contains IC:
11152A-257
Plaque signalétique du produit final
Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante:
Contient des IC: 11152A-257
VT-PNL156-MT65-HD Hardware User Manual
12
VT-PNL156-MT65-HD Hardware User Manual
13
Appendix A: How to Contact Us
If you have any problem or want to know more about our products, visit
www.vantrontech.com or contact us.
US Office: Vantron Technology, Inc.
Address: 440 Boulder Court, Suite 300,
Pleasanton, CA 94566, USA
Tel: 925-621-8758
Email: [email protected]
China Office: Chengdu Vantron Technology, Ltd
Address: 6th Floor, 1st Building, No.9, 3rd Wu Ke East Street,
Wu Hou District, Chengdu 610045, China
Tel: 86-28-8512-3930/3931, 8515-7572/6320
Email: [email protected]
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
Vantron ZB-HD-ANT-257 Manuel utilisateur
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Vantron ZB-HD-ANT-257 User manual
