Q5X QT-5100A Manuel utilisateur

Marque
Q5X
Modèle
QT-5100A
Taper
Manuel utilisateur

Ce manuel convient également à

QT-5100A Module
Description
This document describes the use of the QT-5100A transmitter.
History
Rev 1 Original
QT-5100A Module
Revision: 1
QT-5100 Module Rev 1-march15.doc Page 2 of 8 Q5X Systems, Inc. 2018
FCC Notices:
Information to users:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1.) This device may not cause harmful interference
(2.) This device must accept any interference received, including interference that may cause
undesired operation.
N
OTE
: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications not expressly approved by Quantum5X Systems Inc, could
void the user’s authority to operate the equipment.
Warning: This module has been designed to operate with only the supplied integrated
antenna or the supplied SSMA antenna for the 802.15.4 Radio. Replacing or modifying these
antennas is strictly prohibited.
QT-5100A Module
Revision: 1
QT-5100 Module Rev 1-march15.doc Page 3 of 8 Q5X Systems, Inc. 2018
Innovation, Science and Economic Development Canada (ISED)
This device complies with ISED’s license-exempt RSSs. Operation is subject to the
following two conditions:
1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
1. L’appareil ne doit pas produire de brouillage;
2. L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Cet équipement est conforme Canada limites d'exposition aux radiations dans un environnement non
contrôlé. Cet équipement doit être installé et utilisé à distance minimum de 20cm entre le radiateur et
votre corps.
This radio transmitter (IC: 4614A-QT5100A) has been approved by ISED to operate with the
antenna types listed below with the maximum permissible gain indicated. Antenna types not included
in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Le présent émetteur radio (IC: 4614A-QT5100A) a été approuvé par Industrie Canada pour fonctionner
avec les types d'antenne énumérés ci dessous et ayant un gain admissible maximal. Les types
d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont
strictement interdits pour l'exploitation de l'émetteur.
Approved antenna and connectors
Antenna / Connector
Type
Manufacture Connector Type Max Gain
Integrated Antenna Q5X NA 3dBi
SSMA Whip Antenna Sam Woo Electronics SSMA 0 dB
QT-5100A Module
Revision: 1
QT-5100 Module Rev 1-march15.doc Page 4 of 8 Q5X Systems, Inc. 2018
RF Exposure Compliance:
The QT-5100A Module is granted with a modular approval for mixed mobile and portable applications.
The module is to be used by Quantum5X in their final products without additional FCC/ISED
(Innovation, Science and Economic Development Canada) certification if they meet the following
conditions. Otherwise, additional FCC/ISED approvals must be obtained.
Mobile Application
:
1)
This equipment complies with radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.
2) This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
3) To comply with FCC and ISED regulations limiting both maximum RF output power and human
exposure to RF radiation, the maximum antenna gain including cable loss in a mobile-only
exposure condition must not exceed the 3 dBi.
4) For the 802.15.4 Radio, only approved antenna type with the maximum permissible gain can be
used with this device, such as the supplied fixed attenna or the SSMA whip attenna with a max
gain of 3 dBi.
5) For Canada, the EIRP power shall not to be greater than 250mW to meet ISED regulations
(Conducted power plus antenna gain)
Portable Application
:
This low power module when used in the specfied host configgurationzs listed below complies with
applicable RF exposure requirements that meet FCC/ISED for a portable device, which are approved
with this filing. For this application see the the output power reduction settings in specifiation table
page 8.
PlayerMicS
PlayerMic
AquaMic
RefMic
RefMicHD
Incognito
BeltMic
Module Integration into Host End Products
The QT-5100A Module Transmitter has been designed by Quantum5X Systems Inc. to be used by
Quantum5X as a building block for their wireless audio transmitter products. The module, as designed, is
QT-5100A Module
Revision: 1
QT-5100 Module Rev 1-march15.doc Page 5 of 8 Q5X Systems, Inc. 2018
a standalone unit that is ready for integration into final form factor with the limitation for mobile use as
specified in RF Exposure compliance. For proper usage of the module, the module integrator must
ensure that the input power and input audio signal do not exceed the specified limits as outlined in the
specification section. Failure to do so will result in damage to the module.
Final product(s) after integration with this module shall be tested to comply with all applicable FCC
requirements and Unintentional radiators (FCC section 15.107, 15.109 and ISED ICES-003) before
declaring compliance to Part 15 of the FCC Rules and ISED ICES-003.
The module integrator may not:
1) Alter, modify or remove the module case.
2) Make changes to the Circuit Card Assembly of the module.
3) Remove, change or alter the integrated UHF antenna or the 802.15.4 antenna.
Failure to comply with these restrictions will result in violation of the FCC certification.
Labeling of the End Products:
The modular transmitter must be equipped with either a permanently affixed label.
The modular transmitter must be labeled with its own FCC identification number, and, if the FCC
identification number is not visible when the module is installed inside another device, then the outside
of the device into which the module is installed must also display a label referring to the enclosed
module. This exterior label can use wording such as the following: ‘‘Contains Transmitter Module” or
‘‘Contains “. Any similar wording that expresses the same meaning may be used.
Below are Sample Module and Product lables that must be used for the Module and the Product.
QT-5100A Module
Revision: 1
QT-5100 Module Rev 1-march15.doc Page 6 of 8 Q5X Systems, Inc. 2018
Out-of-the-Box Setup
Ensure the QT-5100A Module has a sufficient charge level by immediately inserting the micro USB
charger.
Note:
The QT-5100A Module should only be charged with the supplied charger and attached Ferrite clamp on
the AC Cord. Failure to use the suppled charger could cause damage the unit or result in violation of the
FCC certification.
Using the Reset Key
Occasionally the QT-5100A has an issue where the unit may occasionally need to be reset after being
connected to a charger. The Reset Key is a small male USB device with a yellow shrink wrap to identify
it.
Use this only if the transmitter becomes unresponsive. The transmitter has 2 microprocessors and
occasionally one may become locked. The Reset Key (which is typically attached to the cable of the
charger) should be inserted into the charge port, held for 1 second, and then removed.
After the Reset Key is removed, the Status LED will blink green 3 times.
There are 2 LED indicators on the QT-5100A Module, Status and Charge.
Charge LED Color
When connected to a charger, the color of the Charge LED will indicate the progress of the charging
cycle. The LED is located on the front of the TX.
Note: After the LED changes from Amber to Green, it is recommended it be charged for 15
more minutes while the trickle charge completes.
GREEN
–
The battery
is charged and ready for use.
AMBER
–
The battery level
audio tests.
RED
–
The battery level is unusable and must be charged
.
QT-5100A Module
Revision: 1
QT-5100 Module Rev 1-march15.doc Page 7 of 8 Q5X Systems, Inc. 2018
Status LED
The Status LED indicates 2 conditions;
1) one condition (On/Off) via the LED blink pattern.
2) the second condition (Battery Level) via the LED color.
Status LED Color
The color of the Status LED indicates the battery charge level;
Note: The meaning of the Status LED’s color is slightly different than the Charge LED’s color. See the
following:
Status LED Blink Patterns
The blink pattern of the Status LED indicates the mode of the QT-5100A.
OFF Mode (no RF, no audio) – The LED is off for 2.5 seconds and on for ¼ of a second, and repeats.
ON Mode (RF on, may have audio, unless the transmitter has been audio muted) – The LED is off for 2.5
seconds and blinks on twice for ¼ of a second, and repeats.
On/Off Pushbutton
The pushbutton is used to turn the QT-5100A on and off. If the transmitter is Off, press and hold the
pushbutton for 3 seconds to turn the transmitter On. If the transmitter is On, press and hold the
pushbutton for 5 seconds to turn the transmitter Off.
2.5 sec
¼ sec
¼ sec
¼ sec
Off
On
Off
On
2.5 sec
Off
2.5 sec
¼ sec
O
ff
On
2.5 sec
¼ sec
O
ff
On
2.5 sec
O
ff
GREEN
–
The battery level is over
50%
.
AMBER
–
The battery level is less than 50%.
RED
–
The battery level is unusable and must be charged
.
QT-5100A Module
Revision: 1
QT-5100 Module Rev 1-march15.doc Page 8 of 8 Q5X Systems, Inc. 2018
Technical Data UHF Radio
RF Carrier Frequency Range: 470.250 MHz – 550 MHz
Working Range – 500m (line of sight, outdoors for a single system with appropriate receive antennas)
Note: Actual working range depends on receiver antenna configuration, RF signal absorption, reflection
and interference.
RF Power Output: see table below
Item # Product Name Max RF Power
1 QT-5100A Module 250 mw
2 PlayerMic (Body Mounted Only) 100 mw
3 PlayerMicL (Body Mounted Only) 100 mw
4 AquaMic (Body Mounted Only) 100 mw
5 RefMic (Body Mounted Only) 100 mw
6 RefMicHD (Body Mounted Only) 250 mw
7 Incognito (Body and head Mounted) 100 mw
9 BeltMic (Body Mounted Only) 100 mw
Technical Data 802.15.4 Radio
RF Power Output: 18 dBm (max)
RF Carrier Frequency Range: 2.405GHz – 2.480GHz
Technical Data QT-5100A Module
Power Requirements: 3.7V Internal Lion battery (non-removable - rechargeable)
Max Input Audio Signal: 1V RMS
Audio Gain Adjustment Range: 0 dB to 30 dB
Overall Dimensions: 35mm X 35mm X 5mm
Net Weight: depends on model
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Q5X QT-5100A Manuel utilisateur

Marque
Q5X
Modèle
QT-5100A
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Autres documents