Panasonic CT-T2 Manuel utilisateur

Marque: Panasonic

Modèle: CT-T2

Catégorie: Des cahiers

Taper: Manuel utilisateur

Ce manuel convient également à

Personal Computer

OPERATING INSTRUCTIONS

Appendix

LIMITED USE LICENSE AGREEMENT .......36

Hard Disk Backup Function...........................38

Hard Disk Data Erase Utility..........................42

Specifications................................................43

LIMITED WARRANTY...................................45

Troubleshooting

List of Error Codes .........................................28

Dealing with Problems (Summary)................... 29

Reinstalling Software .................................... 34

Operation

Starting Up/Shutting Down............................16

Touch Pad .....................................................19

Reference Manual.........................................20

RAM Module ................................................. 21

Useful Information.........................................24

Getting Started

Read Me First ................................................. 3

Names and Functions of Parts........................ 8

First-time Operation ......................................12

Contents

[Additional Manual]

Reference Manual

This manual can be accessed on your computer. Re-

fer to page 20 on how to access the Reference Manual.

Appendix

Getting Started

Operation

Troubleshooting

Please read these instructions carefully before using this product and save this manual for future use.

Model No. CF-T2 Series

Page

Getting Started

Introduction

Thank you for purchasing the Panasonic computer. Read the operating instructions thoroughly for proper operation of your new

computer.

Illustrations and Terminology in this Manual

reproduced in any form without the prior written permission of Matsushita Electric Industrial Co., Ltd.

No patent liability is assumed with respect to the use of the information contained herein.

Disclaimer

Computer specifications and manuals are subject to change without notice. Matsushita Electric Industrial Co., Ltd. assumes no

liability for damage incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manuals.

Trademarks

Microsoft, Windows and the Windows logo are registered trademarks of Microsoft Corporation of the United States and/or other

countries.

Intel, Pentium and PROSet are either registered trademarks or trademarks of Intel Corporation.

SD Logo is a trademark.

Adobe, the Adobe logo and Adobe Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the

United States and/or other countries.

Panasonic is a registered trademark of Matsushita Electric Industrial Co., Ltd.

Names of products, brands, etc., appearing in this manual are trademarks or registered trademarks of their respective owner

companies.

NOTE: NOTE provides a useful fact or helpful information.

CAUTION: CAUTION indicates a condition that may result in minor or moderate injury.

Enter : This illustration means to press the [Enter] key.

Fn + F5 : This illustration means to press and hold the [Fn] key, then press the [F5] key.

When using with the [Fn] and [Ctrl] functions interchanged, read with [Fn] and [Ctrl] reversed (

“Using the Fn Key”).

[start] - [Run]: This illustration means to click [start], then to click [Run].

: Where to go for referred information.

: This illustration means to refer to the Reference Manual, which is available on your computer.

Refer to page 20 on how to access this manual.

Some of the illustrations in this manual may differ slightly in shape from the actual items in order to make the explanation

easier to understand.

In this manual, “Microsoft

Windows

XP Professional Service Pack 2 with Advanced Security Technologies” is indi-

cated as “Windows” or “Windows XP”.

If the user has logged on without the administrator authority, some functions may not be executable, and some screens may

not be displayed as shown in this manual. If this happens, log on with the administrator authority to enable these functions.

Confirm the latest information on optional products in catalogs, etc.

Customer’s Record

Serial No.

Date of Purchase

Model No. *

Code No.

Dealer’s Name

Dealer’s Address

For the Model No., insert the 12 digit number (for example, CF-T2FWATZBM) located on

the bottom of the computer.

Getting Started

Read Me First

Federal Communications Commission Radio

Frequency Interference Statement

Note: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

Consult the Panasonic Service Center or an experienced ra-

dio/TV technician for help.

Warning

To assure continued compliance, use only shielded interface

cables when connecting to a computer or peripheral. Also, any

changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate this equipment.

FCC RF Exposure Warning:

This equipment complies with FCC radiation exposure lim-

its set forth for an uncontrolled environment.

This equipment must be installed and operated in accordance

with provided instructions and minimum 1.5 cm spacing must

be provided between antenna and all person’s body (exclud-

ing extremities of hands, wrist and feet) during wireless

modes of operation.

This transmitter must not be co-located or operated in con-

junction with any other antenna or transmitter.

This computer is provided with a PC Card slot that could be

used with wireless transmitter(s), which will be specifically

recommended, when they become available. Other third-

party wireless transmitter(s) have not been RF exposure

evaluated for use with this computer and may not comply

with FCC RF exposure requirements.

This product is restricted to indoor use due to its operation in

the 5.15 to 5.25 GHz frequency range.

FCC requires this product to be used indoors for the frequency

range 5.15 to 5.25 GHz to reduce the potential for harmful in-

terference to co-channel Mobile Satellite systems.

High power radars are allocated as primary users of the 5.25 to

5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can

cause interference with and /or damage this product.

For U.S.A.

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including

interference that may cause undesired operation.

Responsible Party: Panasonic Corporation of North America

One Panasonic Way

Secaucus, NJ 07094

Tel No:1-800-LAPTOP5 (1-800-527-8675)

FCC Regulation Notice for modem

This equipment contains a FCC approved modem.

FOR HOME OR OFFICE USE

Tested To Comply

With FCC Standards

1. This equipment complies with CFR47 Part 68 rules. On the

computer is a label that contains, among other information,

the FCC registration number and ringer equivalence number

(REN) for this equipment. If required, this information must

be provided to the telephone company.

2. An FCC compliant telephone cord and modular plug is pro-

vided with this equipment. This equipment is designed to be

connected to the telephone network or premises wiring using

a compatible modular jack which is Part 68 compliant. See

Installation Instructions for details.

3. The REN is used to determine the quantity of devices which

may be connected to the telephone line. Excessive RENs on the

telephone line may result in the devices not ringing in response

to an incoming call. In most, but not all area, the sum of RENs

should not exceed five (5.0). To be certain of the number of

devices that may be connected to a line, as determined by the

total RENs, contact the local telephone company.

4. If your telephone equipment cause harm to the telephone net-

work, the telephone company will notify you in advice that

temporary discontinuance of service may be required. But if

advice notice isn’t practical, the telephone company will no-

tify the customer as soon as possible. Also, you will be ad-

vised of your right to file a complaint with the FCC if you

believe it is necessary.

5. The telephone company may take changes in its facilities,

equipment, operations or procedures that could affect the op-

eration of the equipment. If this happens the telephone com-

pany will provide advance notice in order for you to make

necessary modifications to maintain uninterrupted service.

6. If trouble is experienced with this equipment, for repair or

warranty information, please contact Panasonic

Corporation of North America at DIAL TOLL FREE 1-800-

LAPTOP5 (1-800-527-8675). If the equipment is causing

harm to the telephone network, the telephone company may

request that you disconnect the equipment until the problem

is resolved.

7. There are no user serviceable parts contained in this equip-

ment.

8. This equipment may not be used on coin service provided by

the telephone company. Connection to party lines is subject

to state tariffs.

Getting Started

9. The Telephone Consumer Protection Act of 1991 makes it un-

lawful for any person to use a computer or other electronic

device to send any message via a telephone fax machine unless

such message clearly contains in a margin at the top or bottom

of each transmitted page or on the first page of the transmis-

sion, the date and time it is sent and an identification of the

business or other entry, or other individual sending the mes-

sage and the telephone number of the sending machine or such

business, other entity, or individual. In order to program this

information into your fax software, you should refer to the

manual of the Fax software being used.

10.According to the FCC’s electrical safety advisory, we recom-

mend that you may install an AC surge arrestor in the AC outlet

to which this equipment is connected. Telephone companies

report that electrical surges, typically lightning transients, are

very destructive to customer terminal equipment connected to

AC power sources and that this is a major nationwide problem.

Read Me First

For Canada

Industry Canada (IC) Notice for modem

This equipment contains an Industry Canada approved modem unit.

The Industry Canada label is affixed on the modem unit.

EQUIPMENT ATTACHMENT LIMITATIONS

“NOTICE: The Industry Canada label identifies certified

equipment. This certification means that the equipment meets

telecommunications network protective, operational and

safety requirements as prescribed in the appropriate Terminal

Equipment Technical Requirements document(s). The

Department does not guarantee the equipment will operate

to the user’s satisfaction.

Before installing this equipment, users should ensure that it is

permissible to be connected to the facilities of the local

telecommunications company. The equipment must also be

installed using an acceptable method of connection. The customer

should be aware that compliance with the above conditions may

not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a

representative designated by the supplier. Any repairs or

alterations made by the user to this equipment, or equipment

malfunctions, may give the telecommunications company

cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical

ground connections of the power utility, telephone lines and

internal metallic water pipe system, if present, are connected

together. This precaution may be particularly important in rural

areas. Caution: Users should not attempt to make such

connections themselves, but should contact the appropriate

electric inspection authority, or electrician, as appropriate.”

“NOTICE: The Ringer Equivalence Number (REN) assigned

to each terminal device provides an indication of the

maximum number of terminals allowed to be connected to a

telephone interface. The termination on an interface may

consist of any combination of devices subject only to the

requirement that the sum of the Ringer Equivalence Numbers

of all the devices does not exceed 5.”

REN: See bottom of the computer

“Caution: To reduce the risk of fire, use only No.26 AWG or larger telecom-

munication line cord.”

“ATTENTION: Pour réduire le risque d’incendie, utiliser uniquement des

conducteurs de télécommunications 26 AWG ou de section supérieure.”

Notice for the products using LCD

This product uses one or more fluorescent lamps containing a

small amount of mercury. It also contains lead in some compo-

nents. Disposal of these materials may be regulated in your com-

munity due to environmental considerations. For disposal or

recycling information please contact your local authorities, or

the Electronics Industries Alliance: <http://www.eiae.org/>

RESTRICTIONS CONCERNANT LE RACCORDEMENT

DE MATÉRIEL

“AVIS: L’étiquette d’Industrie Canada identifie le matériel

homologué. Cette étiquette certifie que le matériel est

conforme aux normes de protection, d’exploitation et de

sécurité des réseaux de télécommunications, comme le

prescrivent les documents concernant les exigences

techniques relatives au matériel terminal. Le Ministère

n’assure toutefois pas que le matériel fonctionnera à la

satisfaction de l’utilisateur.

Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il

est permis de le raccorder aux installations de l’entreprise

locale de télécommunication. Le matériel doit également être

installé en suivant une méthode acceptée de raccordement.

L’abonné ne doit pas oublier qu’il est possible que la

conformité aux conditions énoncées ci-dessus n’empêche pas

la dégradation du service dans certaines situations.

Les réparations de matériel homologué doivent être

coordonnées par un représentant désigné par le fournisseur.

L’entreprise de télécommunications peut demander à

l’utilisateur de débrancher un appareil à la suite de réparations

ou de modifications effectuées par l’utilisateur ou à cause de

mauvais fonctionnement.

Pour sa propre protection, l’utilisateur doit s’assurer que tous

les fils de mise à la terre de la source d’énergie électrique,

des lignes téléphoniques et des canalisations d’eau

métalliques, s’il y en a, sont raccordés ensemble. Cette

précaution est particulièrement importante dans les régions

rurales. Avertissement: L’utilisateur ne doit pas tenter de faire

ces raccordements lui-même; il doit avoir recours à un service

d’inspection des installations électriques, ou à un électricien,

selon le cas.”

“AVIS: L’indice d’équivalence de la sonnerie (IES) assigné

à chaque dispositif terminal indique le nombre maximal de

terminaux qui peuvent être raccordés à une interface. La

terminaison d’une interface téléphonique peut consister en

une combinaison de quelques dispositifs, à la seule condition

que la somme d’indices d’équivalence de la sonnerie de touts

les dispositifs n’excède pas 5.”

IES: Voir sous le fond de l’ordinateur

Getting Started

Lithium Battery

Lithium Battery!

This computer contains a lithium battery to enable the date, time, and other data to be stored. The battery should only be exchanged

by authorized service personnel.

Warning! A risk of explosion from incorrect installation or misapplication may possibly occur.

Pile au lithium!

Le micro-ordinateur renferme une pile au lithium qui permet de sauvegarder certaines données, notamment la date et l’heure. La

pile ne doit être remplacée que par un technicien qualifié.

Danger! Risque d’explosion en cas de non respect de cette mise en garde!

This product and your Health

This product, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by this product

however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.

Because this product operates within the guidelines found in radio frequency safety standards and recommendations, we believe this

product is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and

result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.

In some situations or environments, the use of this product may be restricted by the proprietor of the building or responsible

representatives of the organization. These situations may for example include:

Using this product on board of airplanes, or

In any other environment where the risk of interference to other devices or services is perceived or identified as harmful.

If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports),

you are encouraged to ask for authorization to use this product prior to turning on the product.

Regulatory Information

We are not responsible for any radio or television interference caused by unauthorized modification of this product. The correction of

interference caused by such unauthorized modification will be the responsibility of the user. We and its authorized resellers or distribu-

tors are not liable for damage or violation of government regulations that may arise from failing to comply with these guidelines.

Information to the User

Important Safety Instructions / Importantes Mesures De Sécurité

When using your telephone equipment, basic safety precautions

should always be followed to reduce the risk of fire, electric

shock and injury to persons, including the following:

1. Do not use this product near water, for example, near a bath

tub, washbowl, kitchen sink or laundry tub, in a wet basement

or near a swimming pool.

2. Avoid using a telephone (other than a cordless type) during

an electrical storm. There may be a remote risk of electric

shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of

the leak.

4. Use only the power cord and batteries indicated in this manual.

Do not dispose of batteries in a fire. They may explode. Check

with local codes for possible special disposal instructions.

SAVE THESE INSTRUCTIONS

Certaines mesures de sécurité doivent être prises pendant l’utilisation

de matérial téléphonique afin de réduire les risques d’incendie, de

choc électrique et de blessures. En voici quelquesunes:

1. Ne pas utiliser l’appareil près de l’eau, p.ex., près d’une baignoire,

d’un lavabo, d’un évier de cuisine, d’un bac à laver, dans un

sous-sol humide ou près d’une piscine.

2. Éviter d’utiliser le téléphone (sauf s’il s’agit d’un appareil sans

fil) pendant un orage électrique. Ceci peut présenter un risque de

choc électrique causé par la foudre.

3. Ne pas utiliser l’appareil téléphonique pour signaler une fuite de

gaz s’il est situé près de la fuite.

4. Utiliser seulement le cordon d’alimentation et le type de piles

indiqués dans ce manual. Ne pas jeter les piles dans le feu: elles

peuvent exploser. Se conformer aux règlements pertinents quant

à l’élimination des piles.

CONSERVER CES INSTRUCTIONS

Industry Canada

This product complies with RSS210 Industry Canada.

Operation is subject to the following two conditions;

(1) this device may not cause interference, and

(2) this device must accept any interference, including interfer-

ence that may cause undesired operation of the device.

This product (local network devices) for the band 5150-5250

MHz is only indoor usage to reduce potential for harmful

interference to co-channel Mobile Satellite systems.

High power radars are allocated as primary users (meaning they

have priority) of 5250-5350 MHz and 5650-5850 MHz and these

radars could cause interference and/or damage to LELAN devices.

Getting Started

Read Me First

Precautions

Avoid Extreme Heat and Cold

Do not store or use the computer in locations

exposed to heat, direct sunlight, or extreme cold.

Avoid moving the computer between locations with

large temperature difference.

Operation: 5

C to 35

C {41

F to 95

Storage: -20

C to 60

C {-4

F to 140

Avoid Direct Sunlight on the LCD Panel

The LCD panel should not be exposed to direct

sunlight or ultraviolet light.

Avoid Humidity, Liquids and Dust

Do not store or use the computer in locations ex-

posed to high humidity, liquids (including rain) or

dust.

Prevent Shock

Avoid subjecting the computer to severe vibrations

or impact. Do not place the computer inside a car

trunk.

Avoid Radio Frequency Interference

Do not place the computer near a television or ra-

dio receiver.

Avoiding Low-temperature Burns

Avoid more than casual contact with any heat pro-

ducing area of the notebook computer, AC adap-

tor, and any option or accessory you use with it.

Even low heat, if warmer than body temperature,

can cause a burn, if the skin is exposed to the heat

source for a long period of time.

Do not touch the computer and cable when it

starts thundering

Keep SD memory cards and MultiMedia Cards

(both sold separately) away from infants and

small children

Accidental swallowing will result in bodily injury.

In the event of accidental swallowing, see a doctor

immediately.

Do not connect a telephone line, or a network cable

other than the one specified, into the LAN port

If the LAN port is connected to a network such as the

ones listed below, a fire or electric shock may result.

• Networks other than 100BASE-TX or 10BASE-T

• Phone lines (Telephone lines, internal phone lines

(on-premise switches), digital public phones, etc.).

Usage Handling

Avoid Magnetic Fields

Keep the computer away from magnets.

Data stored on the hard disk may be lost.

Avoid Stacking

Do not place heavy objects on top of the computer.

Keep Small Objects Away

Do not insert paper clips or other small objects into

the computer.

Do Not Disassemble the Computer

Do not attempt to disassemble your computer.

Avoid Excessive Force on the Display

Do not apply excessive downward force on the

display.

Getting Started

Precautions (Battery Pack)

Care should be exercised with regard to the following in

order to avoid the possibility of overheating, fire or dam-

age.

Avoid Heat

Do not throw the battery pack into a fire or

expose it to excessive heat.

Keep Articles Away

Do not place the battery pack together with ar-

ticles such as necklaces or hairpins when carry-

ing or storing.

Do Not Disassemble

Do not insert sharp objects into the battery pack,

expose it to bumps or shocks, deform, disas-

semble, or modify it.

Do Not Short

Do not short the positive (+) and negative (-)

contacts.

Avoid Extreme Heat, Cold and Direct Sun-

light

Do not charge, use or leave the battery pack for

extended periods where it will be exposed to di-

rect sunlight, in a hot place (in a car on a sunny

day, for example), or in a cold place.

Do Not Use With Any Other Computer

The battery pack is rechargeable and was in-

tended for the specified computer. Do not use it

with a computer other than the one for which it

was designed.

Do not use this computer with a battery pack

other than the one specified (the one included

with the computer or the specified battery

pack sold separately)

Do Not Put into a Microwave

Do not put the battery pack into a microwave

oven or a pressurized chamber.

Stop Using

Should the battery emit an abnormal odor, be-

come hot to the touch, become discolored,

change shape, or become in any way different

from normal, remove it from the computer and

stop using it.

Do not touch the terminals on the battery pack. The battery

pack may no longer function properly if the contacts are

dirty or damaged.

Do not expose the battery pack to water, or allow it to be-

come wet.

If the battery pack will not be used for a long period of time

(a month or more), charge or discharge (use) the battery

pack until the remaining battery level becomes 30% to 40%

and store it in a cool, dry place.

This computer prevents overcharging of the battery by re-

charging only when the remaining power is less than approx.

95% of capacity.

The battery pack is not charged when the computer is first

purchased. Be sure to charge it before using it for the first

time. When the AC adaptor is connected to the computer,

charging begins automatically.

Should the battery leak and the fluid get into your eyes, do

not rub your eyes. Immediately flush your eyes with clear

water and see a doctor for medical treatment as soon as pos-

sible.

NOTE

The battery pack may become warm during recharging

or normal use. This is completely normal.

Recharging will not commence if internal temperature

of the battery pack is outside of the allowable tempera-

ture range (0 °C to 55 °C {32 °F to 131 °F}). (

“Battery Power”) Once the allowable range require-

ment is satisfied, charging begins automatically. Note

that the recharging time varies based on the usage con-

ditions. (Recharging takes longer than usual when the

temperature is 10 °C {50 °F} or below.)

If the temperature is low, the operating time is short-

ened. Only use the computer within the allowable tem-

perature range.

The battery pack is a consumable item. If the amount

of time the computer can be run by using a particular

battery pack becomes dramatically shorter and repeated

recharging does not restore its performance, the battery

pack should be replaced with a new one.

When transporting a spare battery inside a package,

briefcase, etc., it is recommended that it be placed in a

plastic bag so that its contacts are protected.

Always power off the computer when it is not in use.

Leaving the computer on when the AC adaptor is not

connected will exhaust the remaining battery capacity.

Getting Started

Names and Functions of Parts

( page 27, “Wireless LAN”)

Wireless LAN

For information on the key combi-

nations available.

( “Using the Fn Key”)

Keyboard

( page 19)

Touch Pad

( “PC Cards”)

Power Switch

Caps Lock

Numeric Key (NumLk)

Scroll Lock (ScrLk)

Hard disk drive status

To adjust the volume:

Fn + F5 / Fn + F6

Speaker on/off : Fn + F4

Speaker

CAUTION

Do not allow metallic objects or magnetic me-

dia to come near the speaker.

Function Keys

( “Confirm the Status

Using the LEDs”)

Power status

Battery pack status

LED Indicators

PC Card Slot

( “Using the

Touchscreen”)

LCD

Use this jack to connect headphones or

amplifier-equipped speakers. Audio out-

put from the internal speaker is disabled

when headphones or external speakers are

connected.

Headphone Jack

Use only a monaural condenser micro-

phone (miniature jack). Using an input

source other than a monaural condenser mi-

crophone may not allow audio to be input

or may damage the equipment.

Microphone Jack

A Kensington cable can be

connected.

For more information, read

the manual that comes with

the cable.

Security Lock

( page 10)

Stylus Holder

Getting Started

( page 21)

( “Battery Power”)

( “USB Devices (External Mouse etc.)”)

( “External Display”)

USB Ports

DC-IN Jack

DC IN 16V

External Display Port

A lithium ion battery that is

recyclable powers the prod-

uct you have purchased.

Please call 1-800-8-BAT-

TERY for information on

how to recycle this battery.

L’appareil que vous vous

êtes procuré est alimenté par

une batterie au lithium-ion.

Pour des renseignements sur

le recyclage de la batterie,

veuillez composer le 1-800-

8-BATTERY.

( “Modem”)

Modem

SD memory card status

( “SD Memory Card/MultiMedia

Card”)

( “LAN”)

LAN

CAUTION

Do not cover the computer with a thick cloth, such as a blanket.

( page 27, “Wireless LAN”)

Wireless LAN

SD Memory Card Slot

Do not allow metallic objects or

magnetic media to come near this

area.

CAUTION

RAM Module Slot

Battery Pack

( page 17)

Hand Strap

CAUTION

Do not connect the modem telephone cable into the LAN port.

Getting Started

Names and Functions of Parts

Using the Tether

The tether prevents the stylus (included) from falling accidentally. It can be attached to the

stylus holder ( page 11).

Tether

Attaching the Tether

Before Using the Stylus

Attaching or Removing the Stylus Holder

The computer is supplied with the stylus holder attached to the right side of the internal display.

If you want to attach the stylus holder to the left side of the display, use the following method.

Open the display slightly, and stand the computer on its side. (Refer to the illustration on the

left.)

CAUTION

Do the following before attaching or removing the stylus holder.

• Turn off the computer.

• Remove the battery pack and AC adaptor.

• Remove the stylus from the stylus holder.

When attaching or removing the stylus holder, work in a level place.

To attach or remove the stylus holder, use a no. 0 precision Phillips screwdriver.

Using the screwdriver, remove the screws (A, B, C) from the right side of the display.

This detaches the stylus holder (D).

Reattach the screws (A, B, C) to the right side of the display.

Turn the computer over, so that the left side of the display is at the top.

Using the screwdriver, remove the screws (A, B, C) from the left side of the display.

• Be careful not to remove the screw (E).

Attach the stylus holder (D) removed in step to the left side of the display, and fasten the

screws (A, B, C).

CAUTION

Do not carry the computer by gripping the tether.

Getting Started

Attaching and Stowing the Stylus

At the time of purchase, the stylus is not attached to the stylus holder.

With the stylus holder attached, use the following method to attach the supplied stylus to the

stylus holder.

Thread the stylus strap of the tether (a) from (A) in the direction of the arrow, and fasten it to

the hook (B) using a pointed object (e.g., the bent-out tip of a paper clip).

To store the stylus, push the end into (C).

Push in the stylus so that the part (b) is aligned with (D).

CAUTION

Do not carry the computer by gripping the stylus holder.

Getting Started

First-time Operation

Read the steps below to help you learn what parts are included, and to gain an understanding of

some basic computer-related operations.

Confirm the inclusion of all parts.

Make sure the parts shown in the figure have been supplied. If any of these items are

missing or is not working properly, contact your technical support office ( page 45).

Turn the computer over and insert the battery pack.

Make sure the battery pack is facing the correct direction, slide it in the direction of the

arrow, and then check to ensure that the battery pack is held firmly by the latches on the

left and right sides.

CAUTION

Confirm that the latch is properly locked. If it is not, the battery pack may come

off while you are carrying around the computer.

Do not touch the terminals on the battery pack and the computer. The battery

pack may no longer function properly if the contacts are dirty or damaged. Also,

the computer may not operate properly.

Before using the battery pack, carefully read “Precautions (Battery Pack)”

( page 7).

Read the LIMITED USE LICENSE AGREEMENT. ( page 36)

Be sure to read the LIMITED USE LICENSE AGREEMENT before breaking the seal

on the computer's packaging.

Open the display.

1 Slide the latch (A) located at the front.

2 Lift open the display.

CAUTION

Do not open the display wider than necessary (160° or more).

Do not apply excessive pressure to the LCD (B). Also, do not hold the LCD

when opening or closing the display.

Model No : CF-AA1623A

AC adaptor .......... 1

AC Cord ............... 1 Battery Pack ........1

Product Recovery

CD-ROM .............. 3

Modem Telephone

Cable ................... 1

Model No : CF-VZSU24B

( “Using the Touchscreen”)

Operating Instructions

(This book)

.................... 1

Windows

Book .... 1

Refer to page 24 for details on the carrying cloth for protecting the keyboard.

Latches

Battery Pack

Soft Cloth ............1 Stylus ...................1 Tether ..................1

( page 10)

Getting Started

Connect your computer to a power outlet.

CAUTION

Be sure the AC adaptor is connected until completing the first-time use opera-

tion.

When using the computer for the first time, do not connect any peripheral de-

vice except the battery pack and AC adaptor to the computer.

Handling the AC adaptor

Do not twist or pull the AC power cord forcefully. Doing so may damage the

connections.

Use only the specified AC adaptor with your computer. Using an AC adaptor

other than the one supplied might damage the battery and/or the computer.

When the DC plug is not connected to the computer, disconnect the AC cord

from your AC wall outlet.

Problems such as sudden voltage drops may arise during periods of thunder and

lightning. Since this could adversely affect your computer, an uninterruptible

power source (UPS) is highly recommended unless running from the battery

pack alone.

CAUTION

Turn your computer on.

Slide the power switch and hold it for approximately one second until the power

indicator turns on before releasing it.

Do not slide the power switch and hold it for more than four seconds; this will

cause the power to be turned off forcibly.

Do not slide the power switch repeatedly.

Once the computer is powered off, you must wait at least ten seconds before

powering it on again.

7 Setup Windows.

Moving the cursor or clicking buttons can be performed with the touch pad

( page 19).

The battery pack will be charged automatically.

Charging Time: Approx. 3 hours

(Varies depending on the usage conditions.)

Do not press any keys, or touch the touch pad or touchscreen until [Windows

XP Professional Setup] is displayed.

CAUTION

1 At [Welcome to the Windows XP Setup Wizard], click [Next].

2 After reading the agreement, click [I accept this agreement] or [I don’t accept this

agreement], then click [Next].

NOTE

If [I don’t accept this agreement] is selected, the Windows setup will be

aborted.

3 Select settings for your region, then click [Next].

4 Enter your name and organization and then click [Next].

Getting Started

First-time Operation

6 Set the correct date, time and the time zone, then click [Next].

CAUTION

Remember this password! If the password is forgotten, Windows cannot be

operated.

7 Enter your administrator password and click .

5 Enter your computer name and administrator password and then click [Next].

NOTE

It may take some time before the computer restarts and the screen of step 7

is displayed. Wait, and do not press any keys, or touch the touch pad or

touchscreen, etc.

If the keyboard or the touch pad etc. are operated, a message will appear

indicating that there is no response on the screen, or some screens may

appear white. In such cases, also wait until the next screen is displayed.

CAUTION

Remember this password! If the password is forgotten, Windows cannot be

operated. You can create a password reset disk beforehand ( page 15).

Create a new account.

1 Click [start] - [Control Panel] - [User Accounts] - [Create a new account].

2 Enter a new name for the new account, then click [Next].

3 Select [Computer administrator], then click [Create Account].

4 <When you want to create a password for the new account>

Select the new account you have created and click [Create a password].

Follow the instructions on the screen to create a password.

5 Click [start] - [Turn Off Computer] - [Restart] to restart the computer.

When Windows setup is completed, the following message will be displayed

at the bottom right of the screen: “Your computer might be at risk.” Con-

tinue to the next step.

The message is generated by the [Security Center] function in [Control

Panel], and does not indicate an error or malfunction. For more information

about [Security Center]: page 26

NOTE

The computer will restart.

Getting Started

Depending on the Windows settings, installed applications, and drivers, menus and

other displays may differ, or some functions (such as use of the password reset disk)

may be inoperable. Check with your system administrator for details.

You can select Classic view for the Control Panel or select the Classic Start menu.

You can also change the way a user logs on or off.

The procedure in this manual uses the method or view of the Windows XP default

setting (not Classic view nor Classic Start menu etc.).

Resetting the password

Windows XP has a function to reset a forgotten password.

To use this function, you need to create a password reset disk beforehand following

the steps below.

1 Connect the USB floppy disk drive (optional: CF-VFDU03) to your computer.

2 Click [start] - [Control Panel] - [User Accounts].

3 Click [Prevent a forgotten password] from [Related Tasks] menu of the account

you used to logon and create a password reset disk following the on-screen instruc-

tions.

Store the password reset disk in a safe place.

Only the logon password for each account can be reset.

The password set in the Setup Utility cannot be reset.

Information for Windows XP

This concludes the first-time use operation guidelines.

When creating a new user account:

If you make mail settings, create password reset disks ( below), or

conduct other related operations before creating the user account, you will

be unable to use any previous mail history or settings.

When you create the first new account, you can only select [Computer

administrator].

Once a “Computer Administrator” account has been created, you can cre-

ate additional limited user accounts.

Note also that only the added user account will be displayed in the Wel-

come screen. The account for the administrator created during Windows

setup will not be displayed.

The message “Your computer might be at risk,” which is displayed at the

bottom right of the screen, is generated by the “Security Center” function in

Windows XP, and does not indicate an error or malfunction.

To prevent this message from being displayed, refer to “Security of the Com-

puter” ( page 26).

To improve the security of the computer, be sure to refer to “Security of the

Computer” ( page 26) and “Windows Update” ( page 27).

About the Icon Enlarger:

If the characters or icons on the screen are too small and difficult to see,

after completing step 8, click [start] - [All Programs] - [Panasonic] - [Icon

Enlarger]. This will allow you to magnify the display of characters and

icons on the screen. ( “Icon Enlarger”)

The [Icon Enlarger] can be set separately for each account.

You can also use [Loupe Utility], which enlarges a part of the screen. (

“Loupe Utility”)

If the cursor can not be pointed correctly with the stylus, perform [Calibra-

tion] in [start] - [Control Panel] - [Printers and Other Hardware] - [Mouse] -

[TouchScreen].

If you use the wireless LAN, be sure to refer to “Wireless LAN” ( page 27).

NOTE

Operation

Open the display.

Starting Up/Shutting Down

Starting Up

1 Slide the latch (A) located at the front.

2 Lift open the display.

CAUTION

Do not open the display wider than necessary (160° or more).

Do not apply excessive pressure to the LCD. Also, do not hold the LCD when

opening or closing the display.

Turn your computer on.

Slide the power switch and hold it for approximately one second until the power

indicator turns on before releasing it.

CAUTION

Do not slide the power switch and hold it for more than four seconds; this will

cause the power to be turned off forcibly.

While booting, avoid the following until the hard disk drive indicator has

turned off.

• Connecting or disconnecting the AC adaptor.

• Touching the power switch.

• Performing any keyboard, touch pad, touchscreen or external mouse opera-

tions.

• Closing the display.

Do not slide the power switch repeatedly.

Once the computer is powered off, you must wait at least ten seconds before

powering it on again.

When the CPU temperature rises, the computer may not power on to prevent the

CPU from overheating. Should this happen, allow the computer to cool down

then switch the power on again.

If the computer still does not power on, contact your technical support office.

( page 45)

3 Log on to Windows.

After confirming that the hard disk drive indicator has turned off, select the user

and input the password, then select . Until the correct password is entered, the

computer will not operate.

4 Select your application.

You are able to start working on your computer.

Operation

The power saving function is factory set, so if there is no input from a key, the touch

pad, touchscreen or an external mouse (when one is connected) for a certain interval

of time, the power to the LCD and hard disk may be turned off. The LCD will resume

operation when the touch pad, touchscreen or an external mouse (when one is con-

nected) is used or a key is pressed.

The power to the LCD may be turned off even when an application software is being

installed. In this case, because it is conceivable that a selection dialog box will be

shown, do not press Space or Enter to attempt to resume from this condition

as doing so may trigger a selection, but instead, press a key unrelated to the direct

triggering of a selection, like Ctrl .

In addition, when the computer is left alone, it automatically enters the standby or

hibernation mode ( “Standby/Hibernation Functions”). The computer will

resume by sliding the power switch.

You may hear a mechanical “click” shortly after the hard disk indicator has turned off

when there has been no input from a key or device operation, when the computer

enters the standby or hibernation mode, or when Windows is shut down. This is the

sound of the head shifting positions, to reduce power consumption or to protect the

hard disk from shocks. This sound does not indicate a malfunction.

NOTE

If the screen on the left is displayed immediately after you turn

on the power...

A password has been set to ensure the computer’s security.

Enter your password*

and press Enter . ( “Security Measures”)

When the correct password is input, the computer will start.

When three incorrect password attempts or nothing is input for one minute, the com-

puter will power off.

Supervisor Password or User Password set in the Setup Utility (not the Windows password).

How to Use the Hand Strap

The hand strap is convenient for computing while standing.

To carry the computer, put your hand between the computer and the hand strap to prevent it

from falling, and firmly hold the computer when using it.

Operation

Shutting Down (power off your computer)

1 Save important data and close each application.

2 Click [start] - [Turn Off Computer].

3 Click [Turn Off].

Your computer will power off automatically.

Restarting your computer (without shutting down):

Click [Restart].

To shut down using the keyboard:

Press , U , and select [Turn Off] with , then press

Enter .

CAUTION

Do not do the following during the shutdown/restart procedure.

• Connecting or disconnecting the AC adaptor.

• Touching the power switch.

• Performing any keyboard, touch pad, touchscreen or external mouse operations.

• Closing the display.

When you leave the computer or interrupt your work...

If you use the “Standby” or “Hibernation” function, then when you turn on the power next

time, the application software and files you were using before will be displayed, and you

can restart the same operations. ( “Standby/Hibernation Functions”)

Starting Up/Shutting Down

Operation

Touch Pad

Use the touch pad to move the cursor on the screen and perform computer operations.

Function Operation

Moving the Cursor

Tapping/Clicking

Double-Tapping/

Double-Clicking

Dragging

Vertical Scroll

Horizontal Scroll

Move the tip of your finger

lightly over the work surface.

A. Work Surface (Touch Pad)

B. Left Button

C. Right Button

Refer to [Mouse Properties] for information on basic operations other than the above.

To display [Mouse Properties], click [start] - [Control Panel] - [Printers and Other Hard-

ware] - [Mouse].

When using the touch pad, keep the following in mind.

• By design the touch pad is to be used with a finger tip only. Do not place any object on

the work surface or press down forcefully with sharp-pointed objects (e.g., nails) or

hard objects that can leave marks (e.g., pencils and ball point pens).

• Try to avoid having any harmful substances, such as oil, come in contact with the

touch pad. The cursor may not work properly in such cases.

NOTE

Two quick taps, but on the

second tap leaving your fin-

ger down (applying pres-

sure) and moving it on the

work surface.

While holding down the

button, moving your finger

on the work surface.

Trace a circle around the touch pad.

Trace a circle around the touch pad. ( “Using the

Touch Pad”)

The setup is required before using this function. (

“Using the Touch Pad”)

To right-click: Can only be performed by clicking the right but-

ton.

tapping

clicking

double-tapping

double-clicking

Operation

Reference Manual

The Reference Manual and the Important Tips can be accessed on your computer. When a

printer is connected, these manuals can also be printed.

Illustrations may be difficult to view depending on the magnification. If the illustra-

tion is too small, magnify the display.

If a printer is connected, we recommend printing the pages required. The illustrations

and display samples may not be printed with a high quality.

NOTE

Reference Manual

The Reference Manual explains functions for you to make greater use of the computer, such

as how to add peripheral devices, how the Setup Utility works, and other useful information.

How to access the Reference Manual

Click [Reference Manual] in [start].

Important Tips

Important Tips provides information on how to maximize use of the battery pack, which is

necessary for computing away from your home or office.

It also offers helpful explanations on how to use the touchscreen more effectively.

How to access the Important Tips

Double-click on the desktop.

Important Tips can also be accessed from [start] - [All Programs] - [Panasonic] - [On-

Line Manuals] - [Important Tips].

When the Reference Manual or Important Tips is accessed for the first time, the License Agree-

ment of the Adobe Reader may be displayed. If it is displayed, after reading the agreement, click

[Accept] to access the Reference Manual or Important Tips.

Refer to Adobe Reader Help to use the Adobe Reader.

Reference Manual / Important Tips

Contents of the

Reference Manual

La page charge ...

Panasonic CT-T2 Manuel utilisateur

Marque: Panasonic

Modèle: CT-T2

Catégorie: Des cahiers

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Panasonic CT-T2 User manual

Panasonic CT-T2 Manuel utilisateur

Ce manuel convient également à

Panasonic CT-T2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents