Panasonic CF-T1 Series Manuel utilisateur

Marque: Panasonic

Modèle: CF-T1 Series

Catégorie: Des cahiers

Taper: Manuel utilisateur

Ce manuel convient également à

OPERATING INSTRUCTIONS

Personal Computer

Appendix

LIMITED USE LICENSE AGREEMENT ........ 27

Hard Disk Data Erase Utility .......................... 29

Names and Functions of Parts ...................... 30

Specifications ................................................ 31

LIMITED WARRANTY ................................... 32

Troubleshooting

List of Error Codes ......................................... 19

Dealing with Problems (Summary) ....................... 21

Reinstalling Software .................................... 25

Operation

Starting Up/Shutting Down ............................ 14

Touch Pad ..................................................... 17

Reference Manual ......................................... 18

Getting Started

Read Me First.................................................. 3

First-time Operation ........................................ 9

Contents

[Additional Manual]

Reference Manual

This manual can be accessed on your computer. Refer

to page 18 on how to access the Reference Manual.

Reference Manual

• Read Me First • LED Indicators

• Key Combinations

Reference Manual

• Touch Pad

• Touchscreen*

• Display Rotation Tool*

• Standby/Hibernation

Functions

• Security Measures

• Computing on the

Road

• Battery Power

• SD-MovieStage

• PC Cards

• SD Memory Card/

MultiMedia Card

• RAM Module

• External Display

• USB Devices

• Modem

• LAN

• Setup Utility

*Only for models with

touchscreen

Reference Manual

• Technical Information

• DMI Viewer

• List of Error Codes

• Dealing with Problems

(Advanced)

Appendix Getting StartedOperationTroubleshooting

Model No. CF-T1 Series

2000

Please read these instructions carefully before using this product and save this manual for future use.

Getting Started

Introduction

Thank you for purchasing the Panasonic computer. Read the operating instructions thoroughly for proper operation of your new

computer.

Illustrations and Terminology in this Manual

reproduced in any form without the prior written permission of Matsushita Electric Industrial Co., Ltd.

No patent liability is assumed with respect to the use of the information contained herein.

Disclaimer

Computer specifications and manuals are subject to change without notice. Matsushita Electric Industrial Co., Ltd. assumes no

liability for damage incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manuals.

Trademarks

Microsoft, Windows and the Windows logo are registered trademarks of Microsoft Corporation of the United States and/or other

countries.

Intel, Pentium and SpeedStep are either registered trademarks or trademarks of Intel Corporation.

SD Logo is a trademark.

Adobe

and Acrobat

are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or

other countries.

Panasonic is a registered trademark of Matsushita Electric Industrial Co., Ltd.

NOTE: NOTE provides a useful fact or helpful information.

CAUTION: CAUTION indicates a condition that may result in minor or moderate injury.

WARNING: WARNING indicates a hazard that may result in moderate or serious injury.

Windows 2000 : Information for Microsoft

Windows

2000 Professional users.

Windows XP : Information for Microsoft

Windows

XP Professional users.

Enter : This illustration means to press the [Enter] key.

Fn + F5 : This illustration means to press and hold the [Fn] key, then press the [F5] key.

[Start]* - [Run]: This illustration means to click [Start]*, then to click [Run].

(For some applications, you may need to double-click.)

* Windows XP : [start]

: Where to go for referred information.

: This illustration means to refer to the Reference Manual, which is available on your computer.

Refer to page 18 on how to access this manual.

Windows 2000 screens are used in this manual when no specific OS notes are required.

Some of the illustrations in this manual may differ slightly in shape from the actual items in order to make the explanation

easier to understand.

This manual covers two types of models, as distinguished by the type of LCD screen (models with touchscreen and

models without touchscreen).

If the user has logged on without the administrator authority, some functions may not be executable, and some screens

may not be displayed as shown in this manual. If this happens, log on with the administrator authority to enable these

functions.

Customer’s Record

Serial No.

Date of Purchase

Model No. *

Code No.

Dealer’s Name

Dealer’s Address

* For the Model No., insert the 12 digit number (for example, CF-T1R64ZZKM) located on

the bottom of the computer.

Getting Started

Read Me First

Federal Communications Commission Radio

Frequency Interference Statement

Note: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

Consult the Panasonic Service Center or an experienced ra-

dio/TV technician for help.

Warning

To assure continued compliance, use only shielded interface

cables when connecting to a computer or peripheral. Also, any

changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate this equipment.

FCC RF Exposure Warning: This computer is provided with

PC Card slots that could be used with wireless transmitter(s),

which will be specifically recommended, when they become

available. Other third-party wireless transmitter(s) have not been

RF exposure evaluated for use with this computer and may not

comply with FCC RF exposure requirements.

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including

interference that may cause undesired operation.

Responsible Party: Matsushita Electric Corporation of America

One Panasonic Way

Secaucus, NJ 07094

Tel No:1-800-LAPTOP-5 (1-800-527-8675)

For U.S.A.

2. An FCC compliant telephone cord and modular plug is pro-

vided with this equipment. This equipment is designed to be

connected to the telephone network or premises wiring using

a compatible modular jack which is Part 68 compliant. See

Installation Instructions for details.

3. The REN is used to determine the quantity of devices which

may be connected to the telephone line. Excessive RENs on the

telephone line may result in the devices not ringing in response

to an incoming call. In most, but not all area, the sum of RENs

should not exceed five (5.0). To be certain of the number of

devices that may be connected to a line, as determined by the

total RENs, contact the local telephone company.

4. If your telephone equipment cause harm to the telephone net-

work, the telephone company will notify you in advice that

temporary discontinuance of service may be required. But if

advice notice isn’t practical, the telephone company will no-

tify the customer as soon as possible. Also, you will be ad-

vised of your right to file a complaint with the FCC if you

believe it is necessary.

5. The telephone company may take changes in it’s facilities,

equipment, operations or procedures that could affect the op-

eration of the equipment. If this happens the telephone com-

pany will provide advance notice in order for you to make

necessary modifications to maintain uninterrupted service.

6. If trouble is experienced with this equipment, for repair or

warranty information, please contact Matsushita Electric

Corporation of America at DIAL TOLL FREE 1-800-

LAPTOP5 (1-800-527-8675). If the equipment is causing harm

to the telephone network, the telephone company may request

that you disconnect the equipment until the problem is resolved.

7. There are no user serviceable parts contained in this equipment.

8. This equipment may not be used on coin service provided by

the telephone company. Connection to party lines is subject to

state tariffs.

9. The Telephone Consumer Protection Act of 1991 makes it

unlawful for any person to use a computer or other electronic

device to send any message via a telephone fax machine un-

less such message clearly contains in a margin at the top or

bottom of each transmitted page or on the first page of the

transmission, the date and time it is sent and an identification

of the business or other entry, or other individual sending the

message and the telephone number of the sending machine or

such business, other entity, or individual. In order to program

this information into your fax software, you should refer to

the manual of the Fax software being used.

10.According to the FCC’s electrical safety advisory, we recom-

mend that you may install an AC surge arrestor in the AC outlet

to which this equipment is connected. Telephone companies re-

port that electrical surges, typically lightning transients, are very

destructive to customer terminal equipment connected to AC

power sources and that this is a major nationwide problem.

“Caution: To reduce the risk of fire, use only No.26 AWG or larger telecom-

munication line cord.”

“ATTENTION: Pour réduire le risque d’incendie, utiliser uniquement des

conducteurs de télécommunications 26 AWG ou de section supérieure.”

Notice for the products using LCD

This product uses one or more fluorescent lamps containing a

small amount of mercury. It also contains lead in some compo-

nents. Disposal of these materials may be regulated in your com-

munity due to environmental considerations. For disposal or re-

cycling information please contact your local authorities, or the

Electronics Industries Alliance: <http://www.eiae.org/>

FCC Regulation Notice for modem

This equipment contains a FCC approved modem.

Manufacturer of modem: AMBIT Microsystems Corporation

Model No. T60M283.00

FOR HOME OR OFFICE USE

Tested To Comply

With FCC Standards

1. This equipment complies with CFR47 Part 68 rules. On the

computer is a label that contains, among other information,

the FCC registration number and ringer equivalence number

(REN) for this equipment. If required, this information must

be provided to the telephone company.

Getting Started

Read Me First

Important Safety Instructions / Importantes Mesures De Sécurité

When using your telephone equipment, basic safety pre-

cautions should always be followed to reduce the risk of

fire, electric shock and injury to persons, including the fol-

lowing:

1.Do not use this product near water, for example, near a

bath tub, wash bowl, kitchen sink or laundry tub, in a wet

basement or near a swimming pool.

2.Avoid using a telephone (other than a cordless type) dur-

ing an electrical storm. There may be a remote risk of

electric shock from lightning.

3.Do not use the telephone to report a gas leak in the vicin-

ity of the leak.

4.Use only the power cord and batteries indicated in this

manual. Do not dispose of batteries in a fire. They may

explode. Check with local codes for possible special dis-

posal instructions.

SAVE THESE INSTRUCTIONS

Certaines mesures de sécurité doivent être prises pendant

l’utilisation de matérial téléphonique afin de réduire les

risques d’incendie, de choc électrique et de blessures. En

voici quelquesunes:

1.Ne pas utiliser l’appareil près de l’eau, p.ex., près d’une

baignoire, d’un lavabo, d’un évier de cuisine, d’un bac à

laver, dans un sous-sol humide ou près d’une piscine.

2.Éviter d’utiliser le téléphone (sauf s’il s’agit d’un appareil

sans fil) pendant un orage électrique. Ceci peut présenter

un risque de choc électrique causé par la foudre.

3.Ne pas utiliser l’appareil téléphonique pour signaler une

fuite de gaz s’il est situé près de la fuite.

4.Utiliser seulement le cordon d’alimentation et le type de

piles indiqués dans ce manual. Ne pas jeter les piles dans

le feu: elles peuvent exploser. Se conformer aux règlements

pertinents quant à l’élimination des piles.

CONSERVER CES INSTRUCTIONS

For Canada

Industry Canada (IC) Notice for modem

This equipment contains an Industry Canada approved modem unit.

The Industry Canada label is affixed on the modem unit.

EQUIPMENT ATTACHMENT LIMITATIONS

“NOTICE: The Industry Canada label identifies certified

equipment. This certification means that the equipment meets

telecommunications network protective, operational and

safety requirements as prescribed in the appropriate Terminal

Equipment Technical Requirements document(s). The

Department does not guarantee the equipment will operate

to the user’s satisfaction.

Before installing this equipment, users should ensure that it

is permissible to be connected to the facilities of the local

telecommunications company. The equipment must also be

installed using an acceptable method of connection. The

customer should be aware that compliance with the above

conditions may not prevent degradation of service in some

situations.

Repairs to certified equipment should be coordinated by a

representative designated by the supplier. Any repairs or

alterations made by the user to this equipment, or equipment

malfunctions, may give the telecommunications company

cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the

electrical ground connections of the power utility, telephone

lines and internal metallic water pipe system, if present, are

connected together. This precaution may be particularly

important in rural areas. Caution: Users should not attempt

to make such connections themselves, but should contact

the appropriate electric inspection authority, or electrician,

as appropriate.”

“NOTICE: The Ringer Equivalence Number (REN) assigned

to each terminal device provides an indication of the

maximum number of terminals allowed to be connected to a

telephone interface. The termination on an interface may

consist of any combination of devices subject only to the

requirement that the sum of the Ringer Equivalence Numbers

of all the devices does not exceed 5.”

REN: See bottom of the computer

RESTRICTIONS CONCERNANT LE RACCORDEMENT

DE MATÉRIEL

“AVIS: L’étiquette d’Industrie Canada identifie le matériel

homologué. Cette étiquette certifie que le matériel est

conforme aux normes de protection, d’exploitation et de

sécurité des réseaux de télécommunications, comme le

prescrivent les documents concernant les exigences

techniques relatives au matériel terminal. Le Ministère

n’assure toutefois pas que le matériel fonctionnera à la

satisfaction de l’utilisateur.

Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il

est permis de le raccorder aux installations de l’entreprise

locale de télécommunication. Le matériel doit également être

installé en suivant une méthode acceptée de raccordement.

L’abonné ne doit pas oublier qu’il est possible que la

conformité aux conditions énoncées ci-dessus n’empêche

pas la dégradation du service dans certaines situations.

Les réparations de matériel homologué doivent être

coordonnées par un représentant désigné par le fournisseur.

L’entreprise de télécommunications peut demander à

l’utilisateur de débrancher un appareil à la suite de

réparations ou de modifications effectuées par l’utilisateur

ou à cause de mauvais fonctionnement.

Pour sa propre protection, l’utilisateur doit s’assurer que tous

les fils de mise à la terre de la source d’énergie électrique,

des lignes téléphoniques et des canalisations d’eau

métalliques, s’il y en a, sont raccordés ensemble. Cette

précaution est particulièrement importante dans les régions

rurales. Avertissement: L’utilisateur ne doit pas tenter de faire

ces raccordements lui-même; il doit avoir recours à un service

d’inspection des installations électriques, ou à un électricien,

selon le cas.”

“AVIS: L’indice d’équivalence de la sonnerie (IES) assigné

à chaque dispositif terminal indique le nombre maximal de

terminaux qui peuvent être raccordés à une interface. La

terminaison d’une interface téléphonique peut consister en

une combinaison de quelques dispositifs, à la seule condition

que la somme d’indices d’équivalence de la sonnerie de touts

les dispositifs n’excède pas 5.”

IES: Voir sous le fond de l’ordinateur

Getting Started

Cables

Use of an interface cable longer than 3 m (9.84 feet) is not recom-

mended.

PrecautionsLithium Battery

Avoid Extreme Heat and Cold

Do not store or use the computer in locations

exposed to heat, direct sunlight, or extreme cold.

Avoid moving the computer between locations with

large temperature difference.

Operation: 5

C to 35

C {41

F to 95

Storage: -20

C to 60

C {-4

F to 140

Avoid Direct Sunlight on the LCD Panel

The LCD panel should not be exposed to direct

sunlight or ultraviolet light.

Avoid Humidity, Liquids and Dust

Do not store or use the computer in locations exposed

to high humidity, liquids (including rain) or dust.

Prevent Shock

Avoid subjecting the computer to severe vibrations or

impact. Do not place the computer inside a car trunk.

Avoid Radio Frequency Interference

Do not place the computer near a television or ra-

dio receiver.

Avoiding low-temperature burns

Avoid more than casual contact with any heat pro-

ducing area of the notebook computer, AC adap-

tor, and any option or accessory you use with it.

Even low heat, if warmer than body temperature,

can cause a burn, if the skin is exposed to the heat

source for a long enough period of time.

Usage

Handling

Avoid Magnetic Fields

Keep the computer away from magnets.

Data stored on the hard disk may be lost.

Avoid Stacking

Do not place heavy objects on top of the computer.

Keep Small Objects Away

Do not insert paper clips or other small objects into

the computer.

Do Not Disassemble the Computer

Do not attempt to disassemble your computer.

Avoid Excessive Force on the Display

Do not apply excessive downward force on the

display.

Lithium Battery!

This computer contains a lithium battery to enable the date, time,

and other data to be stored. The battery should only be exchanged

by authorized service personnel.

Warning! A risk of explosion from incorrect installation or mis-

application may possibly occur.

Pile au lithium!

Le micro-ordinateur renferme une pile au lithium qui permet de

sauvegarder certaines données comme la date et l’heure

notamment. Elle ne devra être remplacée que par un technicien

qualifié.

Avertissement! Risque d’explosion en cas de non respect de cette

mise en garde!

Getting Started

Precautions (Battery Pack)

NOTE

The battery pack may become warm during recharging or

normal use. This is completely normal.

Recharging will not commence outside of the allowable

temperature range (0 °C to 55 °C {32 °F to 131 °F}). (

“Battery Power”) Once the allowable range re-

quirement is satisfied, charging begins automatically.

Note that the recharging time varies based on the usage

conditions. (Recharging takes longer than usual when the

temperature is 10 °C {50 °F} or less.)

If the temperature is low, the operating time is shortened.

Only use the computer within the allowable temperature

range.

The battery pack is a consumable item. If the amount of

time the computer can be run off a particular battery pack

becomes dramatically shorter and repeated recharging

does not restore its performance, the battery pack should

be replaced with a new one.

When transporting a spare battery inside a package, brief-

case, etc., it is recommended that it be placed in a plastic

bag so that its contacts are protected.

Always power off the computer when it is not in use.

Leaving the computer on when the AC adaptor is not

connected will exhaust the remaining battery capacity.

Care should be exercised with regard to the following in

order to avoid the possibility of overheating, fire or dam-

age.

Avoid Heat

Do not throw the battery pack into a fire or

expose it to excessive heat.

Do Not Disassemble

Do not insert sharp objects into the battery pack,

expose it to bumps or shocks, deform, disas-

semble, or modify it.

Do Not Short

Do not short the positive (+) and negative (-)

contacts.

Do Not Put into a Microwave

Do not put the battery pack into a microwave

oven or a pressurized chamber.

Avoid Extreme Heat, Cold and Direct Sun-

light

Do not charge, use or leave the battery pack for

extended periods where it will be exposed to

direct sunlight, in a hot place (in a car on a sunny

day, for example), or in a cold place.

Keep Articles Away

Do not place the battery pack together with ar-

ticles such as necklaces or hairpins when carry-

ing or storing.

If the battery pack will not be used for a long period of time

(a month or more), charge or discharge (use) the battery pack

until the remaining battery level becomes 30% to 40% and

store it in a cool, dry place.

This computer prevents overcharging of the battery by re-

charging only when the remaining power is less than approx.

95% of capacity.

The battery pack is not charged when the computer is first

purchased. Be sure to charge it before using it for the first

time. When the AC adaptor is connected to the computer,

charging begins automatically.

Should the battery leak and the fluid get into your eyes, do not

rub your eyes. Immediately flush your eyes with clear water

and see a doctor for medical treatment as soon as possible.

Stop Using

Should the battery emit an abnormal odor, be-

come hot to the touch, become discolored,

change shape, or become in any way different

from normal, remove it from the computer and

stop using it.

Do Not Use With Any Other Computer

The battery pack is rechargeable and was in-

tended for the specified computer. Do not use

it with a computer other than the one for which

it was designed.

Do not touch the terminals on the battery pack. The bat-

tery pack may no longer function properly if the contacts

are dirty or damaged.

Do not expose the battery pack to water, or allow it to

become wet.

Read Me First

Getting Started

When Using Peripheral Devices

Pay strict attention to the following points to avoid damage to the computer, peripheral devices, cables, etc.

Also, in addition to following this manual and the Reference Manual, carefully read the instruction manuals for

the peripheral devices being used.

Use only peripheral devices that conform to the computer’s specifications.

Connect the devices properly, paying close attention to the condition and position of the connectors.

If a connection cannot be made easily, do not apply undue force; check once more to confirm the condition

and position of the connector (alignment of pins, etc.) .

If the connector has holding screws, fasten the screws firmly.

Do not carry the computer with cables attached, and do not pull on the cables forcefully.

Saving Data on the Hard Disk

Hard Disk Lock

When the Hard Disk Lock is set to [Enable], it is impossible to read/write data from/to the hard disk when the hard

disk is installed in a different computer, since a password is also set for the hard disk. When the hard disk is

returned to the original computer, you can read/write data as before. In this case, however, make the settings in the

Setup Utility exactly the same as they were before the hard disk was removed. (Note that this Hard Disk Lock

does not guarantee the complete protection of data.

“Security Measures”)

When Disposing of or Transferring Ownership of This Device

When disposing of or transferring ownership of this device, erase all data on the hard disk in order to prevent the

theft of hard disk data. Even if you delete data or initialize the hard disk through normal Windows commands, data

can still be read using special software. In order to erase all data, either have the data erased by a specialist (at a

charge) or use the hard disk data erase utility (included) (

page 29). (Note that this hard disk data erase utility

does not guarantee that data will be completely erased.)

Also, note that if you transfer ownership of this device without deleting commercial software that you have

installed to the hard disk, you may be in violation of the licensing agreement for that software.

Do not expose your computer to shock.

Use care when handling your computer, shock may damage your hard disk or make your software applica-

tions and data unusable.

Do not power off your computer while software applications are running or hard disk drive indicator ( ) is on.

Properly shut Windows* down to avoid problems.

Save all valuable data to disks.

Backing up data to disks will limit damage should trouble occur to your computer or should you inadvert-

ently change or erase data.

Use the security function for all important data. ( “Security Measures” and “SD Memory Card/

MultiMedia Card”)

* Windows 2000 : This computer uses Microsoft

Windows

2000 Professional.

Windows XP : This computer uses Microsoft

Windows

XP Professional.

Environment

Place the computer on a flat stable surface. Do not place the computer upright or allow it to tip over.

When the computer receives extremely strong shock after falling, the hard disk may become inoperable.

In use: Temperature: 5 °C to 35 °C {41 °F to 95 °F}

Humidity : 30% to 80% RH (No condensation)

Not in use: Temperature: -20 °C to 60 °C {-4 °F to 140 °F}

Humidity : 30% to 90% RH (No condensation)

Places not to use your computer

Such areas may result in damage to the computer.

Areas with electronic equipment

These areas may interfere with your display or cause your computer to produce strange sounds.

Areas with extremely high/low temperatures

Do not leave things near the computer that are sensitive to heat. During operation, the computer may

become warm.

Usage Environment

Getting Started

Handling

This computer has been designed so as to minimize shock to the LCD and hard disk drive, etc.,

but no warranty is provided against such trouble. Therefore, as a precision instrument, be

extremely careful in the handling.

Do not carry the computer while the display is open, or carry it by gripping the display or the

cabinet around the display (see figure A). When closing the display, ensure that the latch is

positioned correctly in the slot (

page 10).

Do not carry your computer when the power is on. Lay the carrying cloth that comes with

the computer across the keyboard (see figure B), and close the display gently.

When closing the display, take care to ensure that the carrying cloth does not get caught in

the Panel Switch, and check that the latch on the computer body (

page 10) is properly

aligned.

Do not drop or hit your computer against solid objects.

Remove all external devices, cables, PC Cards sticking out of the computer (see figure C),

SD memory cards, and MultiMedia Cards before transporting the computer.

We recommend preparing a fully charged battery pack.

When transporting a spare battery pack inside a package, briefcase, etc., it is recommended

that it be placed in a plastic bag so that its contacts are protected.

Always carry your computer with you. Never check it in with luggage. For use of the com-

puter inside an aircraft, we recommend asking the airlines regarding their policy on this issue.

It is a good idea to make backup copies on disks and carry them with you.

Read Me First

Touch Pad

page 17

Display

Use the soft cloth included with the computer. (For more information, refer to “Suggestions

About Cleaning the LCD Surface” that comes with the soft cloth.)

Avoid using water when cleaning the panel. Ingredients included in water may leave scratches

and reduce readability of the screen.

Avoid rubbing off dust/dirt with cloth since it may leave scratch on the screen.

Sweep dust/dirt with fine brush, then wipe it with a dry soft cloth used for cleaning glasses.

Apply camera lens cleaner on a soft gauze and clean it with gentle force. Then, wipe with a

dry soft cloth used for cleaning glasses.

Areas excluding the display

Wipe these areas with a soft cloth, after applying water or detergent diluted with water to the

soft cloth and firmly wringing out excess water.

Do not use benzene, thinner, or rubbing alcohol. Doing so may adversely affect the surface, e.g., discoloration. In addition, do

not use commercially-available household cleaners and cosmetics, as they may contain components harmful to the surface.

Do not directly add or spray water or detergent. If liquid enters the inside of the computer, it may cause it to work

improperly or be damaged.

CAUTION

Maintenance

Users are advised to purchase the latest versions of virus protection software and use them regularly.

We recommend you run the software:

• After booting your computer.

• After receiving data.

We recommend that you check data received on disks or from external sources, such as data downloaded

from the Internet, e-mail, etc. (For compressed files, uncompress them before running a check).

Computer Viruses

Carrying

Cloth

Getting Started

First-time Operation

Read the steps below to help you learn what parts are included, and to gain an understanding

of some basic computer-related operations.

Confirm the inclusion of all parts

Make sure the parts shown in the figure have been supplied. If any of these items are

missing or is not working properly, contact your technical support office

( page 32).

Model No : CF-AA1623A

AC adaptor ..........1

Model No :CF-VZSU24

AC Cord ...............1

Battery Pack ........ 1

Product Recovery

CD-ROM

Modem Telephone

Cable ...................1

Windows

Book .... 1

Operating Instructions

(This book)

.................... 1

Windows 2000 ....2

Windows XP .......3

Refer to page 8 for details on the carrying cloth for protecting the keyboard.

Turn the computer over and insert the battery pack

Make sure the battery pack is facing the correct direction, slide it in the direction of the

arrow, and then check to ensure that the battery pack is held firmly by the latches on

the left and right sides.

Latches

CAUTION

Be sure the battery pack is properly connected to the connector.

Do not touch the terminals on the battery pack and the computer. The battery

pack may no longer function properly if the contacts are dirty or damaged. Also,

the computer may not operate properly.

Before using the battery pack, carefully read “Precautions (Battery Pack)”

(

page 6).

Read the LIMITED USE LICENSE AGREEMENT ( page 27)

Before removing the seal covering the power switch, read the LIMITED USE LICENSE

AGREEMENT.

( “Touchscreen”)

Soft Cloth .................................. 1

Stylus ..................................... 1

Battery Pack

Getting Started

Connect your computer to a power outlet

CAUTION

Be sure the AC adaptor is connected until completing Step 8 on page 12.

When using the computer for the first time, do not connect any peripheral de-

vice except the battery pack and AC adaptor to the computer.

Handling the AC adaptor

Do not twist or pull the AC power cord forcefully. Doing so may damage the

connections.

Use only the specified AC adaptor with your computer. Using an AC adaptor

other than the one supplied might damage the battery and/or the computer.

When the DC plug is not connected to the computer, disconnect the AC cord

from your AC wall outlet.

Problems such as sudden voltage drops may arise during periods of thunder and

lightning. Since this could adversely affect your computer, an uninterruptible

power source (UPS) is highly recommended unless running from the battery

pack alone.

Open the display

1 Slide the latch located at the front.

2 Lift open the display.

CAUTION

Do not open the display wider than necessary (160° or more).

Do not apply excessive pressure to the glass part of the display. Also, do

not hold the glass part when opening or closing the display.

CAUTION

Turn your computer on

Slide the power switch and hold it for approximately one second until the power indi-

cator turns on before releasing it.

Do not slide the power switch and hold it for more than four seconds; this will

cause the power to be turned off forcibly.

Do not slide the power switch repeatedly.

Once the computer is powered off, you must wait at least ten seconds before

powering it on again.

7 Setup Windows

Moving the cursor ( ) or clicking buttons can be performed with the touch pad ( page 17).

Do not press any key or move the touch pad until [Windows 2000 Professional

Setup] is displayed.

CAUTION

Windows 2000

1 At the [Welcome to the Windows 2000 Setup Wizard], select [Next].

2 After reading the agreement, select [I accept this agreement] or [I don’t accept this

agreement], then select [Next].

If [I don’t accept this agreement] is selected, the Windows setup will be aborted.

NOTE

3 Select settings for your region, then select [Next].

4 Enter your name and organization and then select [Next].

5 Enter your computer name and administrator password and then select [Next].

Power Switch

Power Indicator

Latch

DC-IN Jack

First-time Operation

Glass Part

DC IN 16V

The battery pack will be charged automatically.

Charging Time: Approx. 3 hours

(Varies depending on the usage conditions.)

Getting Started

6 Enter the correct date, time and the time zone, then select [Next].

You can also complete these settings at a later time. In this case, set [Date and

Time] in [Start] - [Settings] - [Control Panel] - [Date/Time].

7 At [Networking Settings], select [Typical settings], then select [Next].

8 At [Workgroup or Computer Domain], select [No, this computer is not on a

network, or is on a network without a domain], then select [Next].

The computer will restart.

9 At [Welcome to the Network Identification Wizard], select [Next].

At [Users of This Computer], select [Users must enter a user name and pass-

word to use this computer], then select [Next].

Select [Finish].

Enter your administrator password and select [OK].

If the cursor can not be pointed correctly with the stylus, perform [Calibration] in

[Start] - [Settings] - [Control Panel] - [Mouse] - [TouchScreen].

Do not press any key or move the touch pad until [Windows XP Professional

Setup] is displayed.

CAUTION

Windows XP

CAUTION

Remember this password! If the password is forgotten, Windows cannot be

operated. You can create a password reset disk beforehand (

page 13).

6 Enter the correct date, time and the time zone, then select [Next].

You can also complete these settings at a later time. In this case, set [Date and

Time] in [start] - [Control Panel] - [Date, Time, Language, and Regional Options].

7 At [Networking Settings], select [Typical settings], then select [Next].

8 At [Workgroup or Computer Domain], select [No, this computer is not on a

network, or is on a network without a domain], then select [Next].

The computer will restart.

9 Enter your administrator password and select .

If the cursor can not be pointed correctly with the stylus, perform [Calibration] in

[start] - [Control Panel] - [Printers and Other Hardware] - [Mouse] - [TouchScreen].

3 Select settings for your region, then select [Next].

4 Enter your name and organization and then select [Next].

5 Enter your computer name and administrator password and then select [Next].

1 At [Welcome to the Windows XP Setup Wizard], select [Next].

2 After reading the agreement, select [I accept this agreement] or [I don’t accept this

agreement], then select [Next].

NOTE

If [I don’t accept this agreement] is selected, the Windows setup will be aborted.

Remember this password! If the password is forgotten, Windows cannot be

operated.

CAUTION

Getting Started

First-time Operation

CAUTION

Store the floppy disks in a safe place. They will enable you to return your com-

puter to the condition at the time of purchase should any problems occur.

When creating backup disks, do not run any other application program.

When creating backup disks and the message [Insufficient files to copy] is dis-

played, select [OK] and then contact your technical support office

( page 32).

While the floppy disk drive indicator is on, do not remove the floppy disk,

power off your computer or use the standby or hibernation function (

“Standby/Hibernation Functions”).

Be sure to create the backup disk.

If a backup disk is not created, it will be impossible to return the computer to its

original state. In this case, contact your technical support office (

page 32).

The floppy disk drive must be the A drive.

NOTE

8 Create Backup Disks for reinstallation

To create backup disks, the floppy disk drive (optional: CF-VFDU03) and formatted

2HD floppy disks are needed.

1 Connect the USB floppy disk drive to your computer.

2 Prepare 2HD floppy disks and make sure they are not in the write-protected state,

and then set it.

3 Windows 2000

Select [Start] - [Programs] - [Panasonic] - [Create Backup Disk] and follow the

on-screen instructions.

Windows XP

Select [start] - [All Programs] - [Panasonic] - [Create Backup Disk] and follow the

on-screen instructions.

4 Place a label identifying the contents on each disk.

Name of created backup disk

FIRSTAID FD (When the display for creating the UPDATE FD is shown, create

the disk by following the on-screen instructions.)

USB Floppy

Disk Drive

Label on the top surface,

and insert the shutter-

side headfirst.

This concludes the first-time use operation guidelines.

Getting Started

Depending on the Windows settings, installed applications, and drivers, menus and

other displays may differ, or some functions (such as use of the password reset disk)

may be inoperable.

You can select Classic view for the Control Panel or select the Classic Start menu.

You can also change the way a user logs on or off.

The procedure in this manual uses the method or view of the Windows XP default

setting (not Classic view or Classic Start menu etc.).

Resetting the password

Windows XP has a function to reset a forgotten password.

To use this function, you need to create a password reset disk beforehand following

the steps below.

1 Connect the USB floppy disk drive (optional: CF-VFDU03) to your computer.

2 Select [start] - [Control Panel] - [User Accounts] and select the account you used

to logon.

3 Select [Prevent a forgotten password] from the [Related Tasks] menu and create a

password reset disk following the on-screen instructions.

Store the password reset disk in a safe place.

Only the logon password for each account can be reset.

The password set in the Setup Utility cannot be reset.

When you create the first new account, you can only select [Computer administrator].

Only the added user account will be displayed in the Welcome screen. The account for

the administrator created during Windows setup (when the computer is started up for

the first time) will not be displayed.

Information for Windows XP

Operation

1 Open the display

Starting Up/Shutting Down

Starting Up

Slide the latch located at the front.

Lift open the display.

CAUTION

Do not open the display wider than necessary (160° or more).

Do not apply excessive pressure to the glass segment of the display. Also,

do not hold the glass segment when opening or closing the display.

Power Switch

Power Indicator

Latch

Three incorrect attempts

No password for about a minute

The correct password

Will Start

Enter your password* and press Enter . ( “Security Measures”)

Will Not Start

(Power off)

If [Enter Password] is displayed

* Supervisor Password or User Password set in the Setup Utility (not

the Windows password).

Enter Password [ ]

Turn your computer on

Slide the power switch and hold it for approximately one second until the power

indicator turns on before releasing it.

CAUTION

While booting, avoid the following until the hard disk drive indicator ( )

has turned off.

• Connecting or disconnecting the AC adaptor.

• Touching the power switch.

• Performing any keyboard, touch pad, touchscreen (only for models with

touchscreen), or external mouse operations.

• Closing the display.

Once the computer is powered off, you must wait at least ten seconds before

powering it on again.

When using this computer with the battery pack only, it may take some time

for the power to turn on after sliding the power switch. In this case, slide

the power switch and hold it for more than one second. This phenomenon

occurs because the standby power is minimized while the power is turned

off; it is not a malfunction.

When the CPU temperature rises, the computer may not power on to pre-

vent the CPU from overheating. Should this happen, allow the computer to

cool down then switch the power on again.

If the computer still does not power on, contact your technical support office.

(

page 32)

•

When an application or file that was previously displayed

appears on your screen

The standby or hibernation mode has been set ( “Standby/Hibernation Func-

tions”).

OperationOperation

3 Log on to Windows

Windows 2000

After confirming that the hard disk drive indicator (

) has turned off, input the user

name and password, then select [OK]. Until the correct user name and password are

entered, the computer will not operate.

Windows XP

After confirming that the hard disk drive indicator (

) has turned off, select the

user and input the password, then select

. Until the correct password is entered, the

computer will not operate.

The power saving function is factory set, so if there is no input from a key, the touch

pad, the touchscreen (only for models with touchscreen) or an external mouse (when

one is connected) for a certain interval of time, the power to the LCD and hard disk

may be turned off. The LCD will resume operation when the touch pad, the touchscreen

(only for models with touchscreen) or an external mouse (when one is connected) is

used or a key is pressed.

The power to the LCD may be turned off even when an application software is being

installed. In this case, because it is conceivable that a selection dialog box will be

shown, do not press Space or Enter to attempt to resume from this condition

as doing so may trigger a selection, but instead, press a key unrelated to the direct

triggering of a selection, like Ctrl .

In addition, when the computer is left alone, it automatically enters the standby or

hibernation mode (

“Standby/Hibernation Functions”). The computer

will resume by sliding the power switch.

Windows XP

When switching to a different user with the Fast User Switching function, it may

not be possible to set the settings of the display. In this case, log on with the

administrator authority again, not using the Fast User Switching function, and

try the operation once more.

NOTE

4 Select your application

You are able to start working on your computer.

Operation

Shutting Down (power off your computer)

3 Windows 2000

Select [Shut down], then select [OK]

Windows XP

Select [Turn Off]

Your computer will power off automatically.

Restarting your computer (without shutting down)

Windows 2000

Select [Restart], then select [OK].

Windows XP

Select [Restart].

To shut down using the keyboard,

Windows 2000

Press , U , and select [Shut down] with , then press Enter .

Windows XP

Press , U , and select [Turn Off] with , then press Enter .

To quickly resume computer operation after shutting down,

The standby or hibernation function is available (

“Standby/Hibernation

Functions”).

NOTE

This procedure is for shutting down the computer without using the standby or hibernation

function (

“Standby/Hibernation Functions”

)

1 Save important data and close each application

2 Windows 2000

Select [Start] - [Shut Down]

Windows XP

Select [start] - [Turn Off Computer]

Starting Up/Shutting Down

CAUTION

Do not do the following during the shutdown/restart procedure.

• Connecting or disconnecting the AC adaptor.

• Touching the power switch.

• Performing any keyboard, touch pad, touchscreen (only for models with

touchscreen), or external mouse operations.

• Closing the display.

OperationOperation

Touch Pad

Use the touch pad to move the cursor on the display and perform normal computer operations.

Left Button

Work Surface

By design the touch pad is to be used with a finger tip only. Therefore, do not use any

implement which causes damage on the work surface.

NOTE

Refer to [Mouse Properties]* for information on basic operations other than the above.

* Windows 2000 : [Start] - [Settings] - [Control Panel] - [Mouse]

Windows XP : [start] - [Control Panel] - [Printers and Other Hardware] - [Mouse]

Even if the NOTE “The help message in….” appears in the “Touch Pad” section of the Refer-

ence Manual, the statement does not refer to this model.

Even when settings are changed using [Control Panel]

- [Date, Time, Language, and Regional

Options]

- [Regional and Language Options] - [Standards and formats], the display language

within [Mouse Properties]

- [Device Settings] - [Settings] does not change.

NOTE

Right Button

Handling the Touch Pad

Do not place any object on the work surface or press down forcefully with sharp-pointed

objects (e.g., nails) or hard objects that can leave marks (e.g., pencils and ball point pens).

Try to avoid having any harmful substances such as oil, come in contact with the touch pad.

The cursor may not work properly in such cases.

When the touch pad becomes dirty:

Wipe to remove dirt by using a dry soft cloth such as gauze or a soft cloth first applied with

detergent diluted with water and then thoroughly wrung.

Do not use benzene, thinner, or rubbing alcohol.

Doing so may adversely affect the surface,

e.g., discoloration. In addition, do not use commercially-available household cleaners and

cosmetics, as they may contain components harmful to the surface.

Two quick taps, but on the

second tap leaving your fin-

ger down (applying pres-

sure) and moving it on the

work surface.

While holding down the but-

ton, moving your finger on

the work surface.

Function Operation

Moving the Cursor

Tapping/Clicking

Double-Tapping/

Double-Clicking

Dragging

Scroll

Move the tip of your finger

lightly over the work surface.

double-tapping

“Touch Pad”

double-clicking

tapping

clicking

Operation

The Reference Manual can be accessed on your computer. When a printer is connected, the Reference Manual can also be printed.

This manual explains functions for you to make greater use of the computer, such as how to add peripheral devices, how the Setup

Utility works and other useful information. (Refer to the cover of this manual for a list of the main contents included.)

Reference Manual

1 Turn your computer on

2 Windows 2000

Select [Reference Manual] in [Start] - [Programs] - [Panasonic] - [On-Line Manuals]

Windows XP

Select [Reference Manual] in [start]

When the Reference Manual is started up for the first time, the License Agreement of the Acrobat Reader may be displayed.

If it is displayed, after reading the agreement, select [Accept] to access the Reference Manual.

Run the Reference Manual

Illustrations may be difficult to view depending on the magnification. If this is the case, we recommend that the display be

magnified.

The characters in PDF files (such as the Reference Manual) may be difficult to read depending on the Acrobat Reader

settings and the Windows Desktop settings. In such cases, change the Acrobat Reader settings with the following procedure.

1 Start up Acrobat Reader.

2 Select [Edit] - [Preferences] - [Accessibility], and then set [Color Scheme] to [Use colors specified in document].

When the taskbar is hidden at the bottom portion of Acrobat Reader, set the maximum display window size.

If a printer is connected, we recommend printing pages. The illustrations and display samples may not print with a high

quality.

Windows XP

When switching to a different user with the Fast User Switching function, PDF files may not be printed properly. In this case,

log on with the administrator authority again, not using the Fast User Switching function, and try the operation once more.

NOTE

Troubleshooting

List of Error Codes

The following is a list of the messages that BIOS can display. Most of them occur during POST. Some of them display information

about a hardware device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the way it has

been configured. Following the list are explanations of the messages and remedies for reported problems.

If your system displays any of the below error messages other that the ones marked with an asterisk (*), write down the message

and contact your technical support office (

page 32). If your system fails after you make changes in the Setup menus, reset the

computer, enter Setup and install Setup defaults or correct the error.

0200 Failure Fixed Disk

Fixed disk in not working or not configured properly. Check to see if fixed disk is attached properly. Run Setup. Find out if

the fixed-disk type is correctly identified.

0210 Stuck key

Stuck key on keyboard.

0211 Keyboard error

Keyboard not working.

0212 Keyboard Controller Failed

Keyboard controller failed test. May require replacing keyboard controller.

0213 Keyboard locked - Unlock key switch

Unlock the system to proceed.

0230 System RAM Failed at offset : nnnn

System RAM failed at offset nnnn of in the 64k block at which the error was detected.

0231 Shadow RAM Failed at offset : nnnn

Shadow RAM failed at offset nnnn of the 64k block at which the error was detected.

0232 Extended RAM Failed at offset : nnnn

Extended RAM Failed at address line : nnnn

Extended memory not working or not configured properly at offset or address nnnn.

0250 System battery is dead - Replace and run SETUP

The CMOS clock battery indicator shows the battery is dead. Replace the battery and run Setup to reconfigure the system.

*0251 System CMOS checksum bad - Default configuration used

System CMOS has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in

CMOS. The BIOS installed Default SETUP Values. If you do not want these values, enter Setup and enter your own values.

If the error persists, check the system battery or contact your technical support office (

page 32).

0260 System timer error

The timer test failed. Requires repair of system board.

0270 Real time clock error

Real-time clock fails BIOS test. May require board repair.

*0280 Previous boot incomplete - Default configuration used

Previous POST did not complete successfully. POST loads default values and offers to run Setup. If the failure was caused by

incorrect values and they are not corrected, the next boot will likely fail. On systems with control of wait states, improper

Setup settings can also terminate POST and cause this error on the next boot. Run Setup and verify that the wait-state

configuration is correct. This error is cleared the next time the system is booted.

0281 Memory Size found by POST differed from EISA CMOS

Memory size found by POST differed from EISA CMOS.

02B0 Diskette drive A error

02B1 Diskette drive B error

Drive A: or B: is present but fails the BIOS POST diskette tests. Check to see that the drive is defined with the proper diskette

type in Setup and that the diskette drive is attached correctly.

02B2 Incorrect Drive A type - run SETUP

Type of floppy drive A: not correctly identified in Setup.

02B3 Incorrect Drive B type - run SETUP

Type of floppy drive B: not correctly identified in Setup.

02D0 System cache error - Cache disabled

Contact your technical support office (

page 32).

02F0: CPU ID:

CPU socket number for Multi-Processor error.

02F4: EISA CMOS not writable

ServerBIOS2 test error: Cannot write to EISA CMOS.

Troubleshooting

List of Error Codes

02F5: DMA Test Failed

ServerBIOS2 test error: Cannot write to extended DMA (Direct Memory Access) registers.

02F6: Software NMI Failed

ServerBIOS2 test error: Cannot generate software NMI (Non-Maskable Interrupt).

02F7: Fail - Safe Timer NMI Failed

ServerBIOS2 test error: Fail-Safe Timer takes too long.

device address Conflict

Address conflict for specified device.

Allocation Error for: device

Run ISA or EISA Configuration Utility to resolve resource conflict for the specified device.

Failing Bits : nnnn

The hex number nnnn is a map of the bits at the RAM address which failed the memory test. Each 1 (one) in the map indicates

a failed bit. See error 230,231 or 232 for offset address of the failure in System, Extended or Shadow memory.

Invalid System Configuration Data

Problem with NVRAM (CMOS) data.

I/O device IRQ conflict

I/O device IRQ conflict error.

Operating System not found

Operating system cannot be located on either drive A: or drive C:. Enter Setup and see if fixed disk and drive A: are properly

identified.

Parity Check 1 nnnn

Parity error found in the system bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the

address, it displays ????. Parity is a method for checking errors in binary data. A parity error indicates that some data has been

corrupted.

Parity Check 2 nnnn

Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the

address, it displays ????.

Press <F1> to resume, <F2> to Setup

Displayed after any recoverable error message. Press <F1> to start the boot process or <F2> to enter a Setup and change the

settings. Write down and follow the information shown on the screen.

La page charge ...

Panasonic CF-T1 Series Manuel utilisateur

Marque: Panasonic

Modèle: CF-T1 Series

Catégorie: Des cahiers

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Panasonic CF-T1 Series User manual

Documents connexes

Autres documents

Acer Aspire 1602M Guide d'installation