Porter-Cable JOB BOSS C3550 Manuel utilisateur

Direct Drive

Oil Lube

Portable Air Compressor

Instruction

manual

IMPORTANT

Please make certain that the person who is

to use this equipment carefully reads and

understands these instructions before

starting operations.

Part No. D28914-035-0

ESPAÑOL: PÁGINA 27

FRANÇAIS: PAGE 53

To learn more about Porter-Cable

visit our website at:

http://www.porter-cable.com

The Model and Serial No. plate is located on the frame.

Record these numbers in the spaces below and retain for

future reference.

Model No.

Type

Serial No.

Model

C3550

2- ENG

D28914

SAFETY GUIDELINES - DEFINITIONS

Indicates an imminently

hazardous situation

which, if not avoided, will

result in death

or serious injury.

Indicates a potentially

hazardous situation

which, if not avoided, could

result in

death or serious injury.

Indicates a potentially

hazardous situation

which, if not avoided, may

result in

minor or moderate injury.

Used without the safety

alert symbol indicates a

potentially hazardous situation which, if

not avoided, may result in pr

operty

damage.

This manual contains information that is important for you to know and

understand. This information relates to protecting YOUR SAFETY and

PREVENTING EQUIPMENT PROBLEMS. To help you recognize this

information, we use the symbols below. Please read the manual and pay

attention to these symbols.

IMPORTANT SAFETY INSTRUCTIONS

Some dust created by power sanding, sawing, grinding,

drilling, and other construction activities contains chemicals

known (to the State of California) to cause cancer, birth defects or other

reproductive harm. Some example of these chemicals are:

●

lead from lead-based paints

●

crystalline silica from bricks and cement and other masonry products

●

arsenic and chromium from chemically-treated lumber

Your risk from these exposures varies, depending on how often you do this

type of work. To reduce your exposure to these chemicals: work in a well

ventilated area, and work with approved safety equipment, always wear

MSHA/NIOSH approved, properly fitting face mask or respirator when using

such tools.

When using air tools, basic safety precautions should always be followed to

reduce the risk of of personal injury.

3- ENG

D28914

IMPORTANT SAFETY INSTRUCTIONS

Save these instructions

Improper operation or maintenance of this product could result in serious injury and

property damage. Read and understand all warnings and operation instructions before

using this equipment.

HAZARD

WARNING: Risk of explosion or fire

How To Prevent It

What Could Happen

It is normal for electrical contacts

within the motor and pressure switch to

spark.

If electrical sparks from compressor

come into contact with flammable

vapors, they may ignite, causing fire or

explosion.

Restricting any of the compressor

ventilation openings will cause serious

overheating and could cause fire.

Unattended operation of this product

could result in personal injury or

property damage. To reduce the risk of

fire, do not allow the compressor to

operate unattended.

Always operate the compressor in a well

ventilated area free of combustible

materials, gasoline, or solvent vapors.

If spraying flammable materials, locate

compressor at least 20 feet away from

spray area. An additional length of hose

may be required.

Store flammable materials in a secure

location away from compressor.

Never place objects against or on top

of compressor. Operate compressor in

an open area at least 12 inches away

from any wall or obstruction that would

restrict the flow of fresh air to the

ventilation openings.

Operate compressor in a clean, dry well

ventilated area. Do not operate unit

indoors or in any confined area.

Always remain in attendance with the

product when it is operating.

Always disconnect electrical power by

moving pressure switch lever to the off

position and drain tank daily or after

each use.

4- ENG

D28914

WARNING: Risk of Bursting

Air Tank: The following conditions could lead to a weakening of the tank, and result

in a violent tank explosion and could cause property damage or serious injury.

How To Prevent It

What Could Happen

WARNING: Risk from Flying Objects

The compressed air stream can cause

soft tissue damage to exposed skin

and can propel dirt, chips, loose

particles, and small objects at high

speed, resulting in property damage or

personal injury.

Always wear ANSI Z87.1 approved safety

glasses with side shields when using the

compressor.

Never point any nozzle or sprayer

toward any part of the body or at other

people or animals.

Always turn the compressor off and

bleed pressure from the air hose and tank

before attempting maintenance, attaching

tools or accessories.

HAZARD

Drain tank daily or after each use. If

tank develops a leak, replace it

immediately with a new tank or replace

the entire compressor.

Failure to properly drain condensed

water from tank, causing rust and

thinning of the steel tank.

Modifications or attempted repairs to

the tank.

Unauthorized modifications to the

unloader valve, safety valve, or any

other components which control tank

pressure.

Never drill into, weld, or make any

modifications to the tank or its

attachments.

Excessive vibration can weaken the

air tank and cause rupture or

explosion

The tank is designed to withstand specific

operating pressures. Never make

adjustments or parts substitutions to

alter the factory set operating

pressures.

For essential control of air pressure, you

must install a pressure regulator and

pressure gauge to the air outlet (if not

equipped) of your compressor. Follow the

equipment manufacturers

recommendation and never exceed the

maximum allowable pressure rating of

attachments. Never use compressor to

inflate small low pressure objects such

as children’s toys, footballs,

basketballs, etc.

A

TTACHMENTS & ACCESSORIES:

Exceeding the pressure rating of air

tools, spray guns, air operated

accessories, tires, and other inflatables

can cause them to explode or fly apart,

and could result in serious injury.

How To Prevent It

What Could Happen

5- ENG

D28914

WARNING: Risk to Breathing

WARNING: Risk of Electrical Shock

HAZARD

Your air compressor is powered by

electricity. Like any other electrically

powered device, If it is not used

properly it may cause electric shock.

Repairs attempted by unqualified

personnel can result in serious injury

or death by electrocution.

Electrical Grounding: Failure to provide

adequate grounding to this product

could result in serious injury or death

from electrocution.

See grounding instructions.

Never operate the compressor outdoors

when it is raining or in wet conditions.

Never operate compressor with

protective covers removed or damaged.

Any electrical wiring or repairs required

on this product should be performed by

authorized service center personnel in

accordance with national and local

electrical codes.

Make certain that the electrical circuit to

which the compressor is connected

provides proper electrical grounding,

correct voltage and adequate fuse

protection.

The compressed air directly from your

compressor is not safe for breathing.

The air stream may contain carbon

monoxide, toxic vapors, or solid

particles from the tank. Breathing these

contaminants can cause serious injury

or death.

Sprayed materials such as paint, paint

solvents, paint remover, insecticides,

weed killers, may contain harmful

vapors and poisons.

Air obtained directly from the compressor

should never be used to supply air for

human consumption. In order to use air

produced by this compressor for

breathing, suitable filters and in-line

safety equipment must be properly

installed. In-line filters and safety

equipment used in conjunction with the

compressor must be capable of treating

air to all applicable local and federal

codes prior to human consumption.

Work in an area with good cross

ventilation. Read and follow the safety

instructions provided on the label or

safety data sheets for the materials you

are spraying. Use a NIOSH/ MSHA

approved respirator designed for use with

your specific application.

How To Prevent It

What Could Happen

How To Prevent It

What Could Happen

6- ENG

D28914

WARNING: Risk of Burns

Touching exposed metal such as the

compressor head or outlet tubes, can

result in serious burns.

Never touch any exposed metal parts

on compressor during or immediately

after operation. Compressor will remain

hot for several minutes after operation.

Do not reach around protective shrouds

or attempt maintenance until unit has

been allowed to cool.

WARNING: Risk from Moving Parts

Never operate the compressor with

guards or covers which are damaged or

removed.

Moving parts such as the pulley, flywheel,

and belt can cause serious injury if they

come into contact with you or your

clothing.

WARNING: Risk of Falling

A portable compressor can fall from a

table, workbench, or roof causing

damage to the compressor and could

result in serious injury or death to the

operator.

Always operate compressor in a stable

secure position to prevent accidental

movement of the unit. Never operate

compressor on a roof or other elevated

position. Use additional air hose to

reach high locations.

HAZARD

Any repairs required on this product

should be performed by authorized

service center personnel.

Attempting to operate compressor with

damaged or missing parts or attempting

to repair compressor with protective

shrouds removed can expose you to

moving parts and can result in serious

injury.

How To Prevent It

What Could Happen

How To Prevent It

What Could Happen

How To Prevent It

What Could Happen

7- ENG

D28914

Review and understand all instructions

and warnings in this manual.

Become familiar with the operation and

controls of the air compressor.

Keep operating area clear of all persons,

pets, and obstacles.

Keep children away from the air

compressor at all times.

Do not operate the product when

fatigued or under the influence of

alcohol or drugs. Stay alert at all times.

Never defeat the safety features of this

product.

Equip area of operation with a fire

extinguisher.

Do not operate machine with missing,

broken, or unauthorized parts.

WARNING: Risk of Unsafe Operation

Unsafe operation of your air compressor

could lead to serious injury or death to

you or others.

HAZARD

WARNING: Risk of Serious Injury or Property Damage When

Transporting Compressor

Oil can leak or spill and could result in

fire or breathing hazard; serious injury or

death can result. oil leaks will damage

carpet, paint or other surfaces in

vehicles or trailers.

Always place COMPRESSOR on a

protective mat when transporting to

protect against damage to vehicle from

leaks. Remove COMPRESSOR from

vehicle immediately upon arrival at your

destination.

(Fire, Inhalation, Damage to Vehicle Surfaces)

HAZARD

SAVE THESE INSTRUCTIONS

How To Prevent It

What Could Happen

How To Prevent It

What Could Happen

8- ENG

D28914

GLOSSARY

Become familiar with these terms before operating the unit.

CFM: Cubic feet per minute.

SCFM: Standard cubic feet per minute; a unit of measure of air delivery.

PSIG: Pounds per square inch gauge; a unit of measure of pressure.

Code Certification: Products that bear one or more of the following marks:

UL, CUL, ETL, CETL, have been evaluated by OSHA certified independent

safety laboratories and meet the applicable Underwriters Laboratories

Standards for Safety.

Cut-In Pressure: While the motor is off, air tank pressure drops as you

continue to use your accessory. When the tank pressure drops to a certain low

level the motor will restart automatically. The low pressure at which the motor

automatically restarts is called “cut-in” pressure.

Cut-Out Pressure: When an air compressor is turned on and begins to run,

air pressure in the air tank begins to build. It builds to a certain high pressure

before the motor automatically shuts off - protecting your air tank from

pressure higher than its capacity. The high pressure at which the motor shuts

off is called “cut-out” pressure.

Branch Circuit: Circuit carrying electricity from electrical panel to outlet.

DUTY CYCLE

This air compressor pump is capable of running continuously. However, to

prolong the life of your air compressor, it is recommended that a 50%-75%

average duty cycle be maintained; that is, the air compressor pump should not

run more than 30-45 minutes in any given hour.

SPECIFICATIONS

Model No. C3550

Horsepower Peak 2.5

Bore 2.363

Stroke .890

* Voltage-Single Phase 120

* * Minimum Branch Circuit Requirement 15 amps

* Fuse Type Time Delay

Air Tank Capacity (Gallon) 4.5 ASME

Approximate Cut-in Pressure 120 PSIG

Approximate Cut-out Pressure 150 PSIG

SCFM @ 40 PSIG 5.7

SCFM @ 90 PSIG 4.4

* These compressors can be operated on a 15 amp

circuit if:

1. Voltage supply to circuit must comply with the National Electrical Code.

2. Circuit is not used to supply any other electrical needs (lights, appliances, etc.)

3. Extension cords comply with specifications in owners manual.

4. Circuit is equipped with 15 amp circuit breaker or 15 amp time delay fuse.

If any of the above conditions cannot be met, or if operation of the compressor

repeatedly causes interruption of the power it may be necessary to operate it

from a 20 amp circuit. It is not necessary to change the cord set.

** A circuit breaker is preferred. Use only a fuse or circuit breaker that is the

same rating as the branch circuit the air compressor is operated on. If the air

compressor is connected to a circuit protected by fuses, use time delay

fuses.

9- ENG

D28914

To Add Oil To Pump

DO NOT ATTEMPT TO OPERATE THIS AIR COMPRESSOR

WITHOUT FIRST ADDING OIL TO THE CRANKCASE.

Serious damage can result from even limited operation unless filled with

oil and broken in correctly. Make sure to closely follow initial start-up

procedures.

COMPRESSORS ARE SHIPPED WITHOUT OIL. A small

amount of oil may be present in the pump upon receipt of

the air compressor. This is due to plant testing and does not mean the

pump contains oil.

Multi-Viscosity motor oils, like 10W 30, should not be used

in an air compressor. They leave carbon deposits on

critical components, thus reducing performance and compressor life. Use

air compressor oil only.

NOTE: Use an air compressor oil such as SAE-30 (API CG/CD heavy duty

motor oil). Under extreme winter conditions use SAE-10 weight oil.

1. Place unit on a level surface.

Drain tank to release air pressure before removing the

dipstick.

Make sure air vent (B) in

dipstick is free from

debris. If air vent is blocked pressure

can build in crankcase causing damage

to air compressor and possible personal

injury.

2. Remove dipstick (A) and slowly fill

crankcase with oil. Crankcase

capacity is 8 fluid ounces (236.6 ml).

Oil level should be at the + (full) mark

on the dipstick.

NOTE: If the oil is added too quickly, it will

overflow and appear to be full.

3. Replace dipstick.

Accessories for this unit are available at the store the unit was purchased.

ACCESSORIES

ASSEMBLY

+

-

A

B

+ full

- add

One accessory available for this unit

is the Job Boss ™ Mobility Kit, this

accessory includes retractable

handle, comfort grip, mounting

bracket, pneumatic wheels, shoulder

bolts, and all associated hardware

needed to make this unit more

mobile.

Unit shown with

PTA50 Mobility kit,

sold separately.

10- ENG

D28914

GROUNDING INSTRUCTIONS

RISK OF ELECTRICAL SHOCK. In the event of a short

circuit, grounding reduces the risk of shock by providing

an escape wire for the electric current. This air compressor must be

properly grounded.

The portable air compressor is equipped with a cord having a grounding wire

with an appropriate grounding plug (see following illustrations).

1. The cord set and plug with this unit contains a grounding pin. This plug

MUST be used with a grounded outlet.

IMPORTANT: The outlet being used must

be installed and grounded in accordance

with all local codes and ordinances.

2. Make sure the outlet being used has

the same configuration as the

grounded plug. DO NOT USE AN

ADAPTER. See illustration.

3. Inspect the plug and cord before each

use. Do not use if there are signs of

damage.

4. If these grounding instructions are not completely understood, or if in

doubt as to whether the compressor is properly grounded, have the

installation checked by a qualified electrician.

IMPROPER GROUNDING CAN RESULT IN ELECTRICAL

SHOCK.

Do not modify the plug provided. If it does not fit the available outlet, a

correct outlet should be installed by a qualified electrician.

Repairs to the cord set or plug MUST be made by a qualified electrician.

INSTALLATION

Location of the Air Compressor

Locate the air compressor in a clean, dry, and well ventilated area.

The air compressor should be located at least 12" away from the wall or

other obstructions that will interfere with the flow of air.

The air filter must be kept clear of obstructions which could reduce air flow

to the air compressor.

The air compressor requires fresh air flow for proper cooling. DO NOT

ALLOW THE COMPRESSOR TO GET WET.

HOW TO SET UP YOUR UNIT

Grounding Pin

Grounded

Outlets

Plug

11- ENG

D28914

Extension Cords

Using extension cords is not recommended. The use of extension cords will

cause voltage to drop resulting in power loss to the motor and overheating.

Instead of using an extension cord, increase the working reach of the air hose

by attaching another length of hose to its end. Attach additional lengths of

hose as needed.

If an extension cord must be used, be sure it is:

• a 3-wire extension cord that has a 3-blade grounding plug, and a 3-slot

receptacle that will accept the plug on the product

• in good condition

• no longer than 50 feet

• 12 gauge (AWG) or larger. (Wire size increases as gauge number

decreases. 10 AWG and 8 AWG may also be used. DO NOT USE 14 OR

16 AWG.)

Voltage and Circuit Protection

Refer to the specification chart for the voltage and minimum branch circuit

requirements.

Certain air compressors can be operated on a 15 amp circuit if the following

conditions are met.

1. Voltage supply through branch circuit is 15 amps.

2. Circuit is not used to supply any other electrical needs (lights, appliances,

etc.).

3. Extension cords comply with specifications.

4. Circuit is equipped with a 15 amp circuit breaker or 15 amp time delay

fuse. NOTE: If compressor is connected to a circuit protected by fuses,

use only time delay fuses. Time delay fuses should be marked “D” in

Canada and “T” in the US.

If any of the above conditions cannot be met, or if operation of the compressor

repeatedly causes interruption of the power, it may be necessary to operate it

from a 20 amp circuit. It is not necessary to change the cord set.

12- ENG

D28914

OPERATION

Know Your Air Compressor

READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING

YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with

the location of various controls and adjustments. Save this manual for future

reference.

Description of Operation

Become familiar with these controls before operating the unit.

On/Auto/Off Switch (A): Turn this

switch ON to provide automatic power

to the pressure switch and OFF to

remove power at the end of each use.

Pressure Switch (B): The pressure

switch automatically starts the motor

when the air tank pressure drops below

the factory set “cut-in” pressure. It stops

the motor when the air tank pressure

reaches the factory set “cut-out”

pressure.

Safety Valve (C): If the pressure switch

does not shut off the air compressor at

its “cut-out” pressure setting, the safety valve will protect against high pressure

by “popping out” at its factory set pressure (slightly higher than the pressure

switch “cut-out” setting).

Outlet Pressure Gauge(D):

The outlet pressure gauge

indicates the air pressure

available at the outlet side

of the regulator. This

pressure is controlled by the

regulator and is always less

than or equal to the tank

pressure.

Tank Pressure Gauge(E): The tank pressure gauge indicates the reserve air

pressure in the tank.

Regulator (F): Controls the air pressure shown on the outlet pressure gauge.

Pull the knob out and turn clockwise to increase pressure and

counterclockwise to decrease pressure. When the desired pressure is reached

push knob in to lock in place.

Universal Quick-Connect Body (G): The universal quick-connect body

accepts the three most popular styles of quick-connect plugs- Industrial,

automotive (Tru-flate), and ARO. One hand push-to-connect operation makes

connections simple and easy. The two quick connect bodies allow the use of

two tools at the same time.

Remote Console (H): Permits remote air regulation and control closer to work

area, includes two high-flow industrial/automotive style compatible quick-

connects, outlet pressure gauge, and a high-flow regulator.

G

E

A

C

B

D

F

H

13- ENG

D28914

Drain Valve (I): The drain valve is

located at the base of the air tank and is

used to drain condensation at the end of

each use.

Cooling System (not shown): This

compressor contains an advanced

design cooling system. At the heart of

this cooling system is an engineered fan.

It is perfectly normal for this fan to blow air over the pump head, cylinder

sleeve, and crankcase. You know the cooling system is working when air is

being expelled.

Air Compressor Pump (not shown): Compresses air into the air tank.

Working air is not available until the compressor has raised the air tank

pressure above that required at the air outlet.

Dipstick (J): Indicates the amount of oil in the pump, the

+ mark indicates full and the - mark indicates oil needs to

be added. See Oil paragraphs in the Maintenance section

for instructions.

Motor Thermal Overload Protector (not shown): The

motor has an automatic reset thermal overload protector.

If the motor overheats for any reason, the overload

protector will shut off the motor. The motor must be

allowed to cool down before restarting. The compressor

will automatically restart after the motor cools.

Air Intake Filter (K): This filter is designed to clean air

coming into the pump. This filter must always be clean

and ventilation openings free from obstructions. See

"Maintenance".

Check Valve (L): When the air compressor is

operating, the check valve is “open”, allowing

compressed air to enter the air tank. When the air

compressor reaches “cut-out” pressure, the check

valve “closes”, allowing air pressure to remain inside

the air tank.

Pressure Release Valve (M): The pressure release

valve located on the side of the pressure switch, is

designed to automatically release compressed air from

the compressor head and the outlet tube when the air

compressor reaches “cut-out” pressure or is shut off.

The pressure release valve allows the motor to restart

freely. When the motor stops running, air will be heard

escaping from this valve for a few seconds. No air

should be heard leaking when the motor is running, or

continuous leaking after unit reaches “cut-out” pressure.

M

How to Use Your Unit

How to Stop:

1. Set the On/Auto/Off lever to “OFF”.

J

L

K

I

14- ENG

D28914

Before Starting

Break-in Procedure

Serious damage may result if the following break-in

instructions are not closely followed.

This procedure is required before the air compressor is put into service and

when the check valve or a complete compressor pump has been replaced.

1. Make sure the On/Auto/Off lever is in the "OFF" position.

2. Check oil level in pump. See “Oil” paragraph in the “Maintenance” section

for instructions.

3.

Plug the power cord into the correct branch circuit receptacle.

(Refer to

Voltage and Circuit Protection paragraph in the Installation section of this

manual.)

4. Open the drain valve fully (counter-clockwise) to permit air to escape and

prevent air pressure build up in the air tank during the break-in period.

5. Move the On/Auto/Off lever to "ON/AUTO" position. The compressor will

start.

6. Run the compressor for 20 minutes. Make sure the drain valve is open and

there is minimal air pressure build-up in tank.

7. After 20 minutes, close the drain valve (clockwise). The air receiver will fill

to “cut-out” pressure and the motor will stop.

The compressor is now ready for use.

Before Each Start-Up:

1. Place On/Auto/Off lever to “OFF”.

2. Pull regulator knob out, turn counter-clockwise until it stops. Push knob in

to lock in place.

3. Attach hose and accessories. NOTE: The hose or accessory will require a

quick connect plug. To use remote console, see "How to Use Remote

Console" paragraph in this section.

Too much air pressure causes a hazardous risk of

bursting. Check the manufacturer’s maximum pressure

rating for air tools and accessories. The regulator outlet pressure must

never exceed the maximum pressure rating.

15- ENG

D28914

How to Start:

1. Turn the On/Auto/Off lever to “AUTO” and allow tank pressure to build.

Motor will stop when tank pressure reaches “cut-out” pressure.

2. Pull the regulator knob out and turn clockwise to increase pressure. When

the desired pressure is reached push knob in to lock in place. The

compressor is ready for use.

NOTE: Always operate the air compressor in well-ventilated areas free of

gasoline or other combustible vapors. If the compressor is being used to

operate a sprayer DO NOT place near the spray area.

How to Use Remote Console:

When needed the remote console allows remote air regulation and control

closer to the work area.

Reduce air pressure in tank to 60 psi maximum before

removing or connecting portable control panel and when

connecting hose to tank quick-connect coupler.

1. Turn knobs counter clockwise to loosen knobs securing control panel.

2. Slide console up and away from frame, disconnect air hose from quick

connect (a), and remove console.

3. Connect air hose (sold separately) to quick connect plug (b) and quick

connect (a). The console can then be brought closer to the work site to

rest on the console brackets (d) or be temporarily mounted using the

mounting hole (c).

Can cause serious injury or death. Tank may contain 150

PSI of air pressure. Never connect accessories to

unregulated air. Never operate tools or accessories above marked

maximum pressure.

a

b

c

d

16- ENG

D28914

MAINTENANCE

Customer Responsibilities

Daily or

after

each

use

Before

each

use

●

Every

8

hours

Every

40

hours

Every

100

hours

Yearly

Every

160

hours

●

1

1- more frequent in dusty or humid conditions

Check Safety Valve

Drain Tank

Oil Leaks

Check Oil

Change Oil

Air Filter

NOTE: See “Operation” section for the location of controls.

To ensure efficient operation and longer life of the air compressor outfit, a

routine maintenance schedule should be prepared and followed. The following

routine maintenance schedule is geared to an outfit in a normal working

environment operating on a daily basis. If necessary, the schedule should be

modified to suit the conditions under which your compressor is used. The

modifications will depend upon the hours of operation and the working

environment. Compressor outfits in an extremely dirty and/or hostile

environment will require a greater frequency of all maintenance checks.

Unit cycles automatically when power is on. When

performing maintenance, you may be exposed to voltage

sources, compressed air, or moving parts. Personal injuries can occur.

Before performing any maintenance or repair, disconnect power source

from the compressor and bleed off all air pressure.

To Check Safety Valve

If the safety valve does not work properly, over

pressurization may occur, causing air tank rupture or an

explosion.

1. Before starting compressor, pull the ring on the safety valve to make sure

that the safety valve operates freely. If the valve is stuck or does not

operate smoothly, it must be replaced with the same type of valve.

To Drain Tank

1. Set the On/Auto/Off lever to “OFF”.

2. Pull the regulator knob out and turn counter clockwise to set the outlet

pressure to zero.

3. Remove the air tool or accessory.

4. Pull ring on safety valve allowing air to bleed from the tank until tank

pressure is approximately 20 psi. Release safety valve ring.

17- ENG

D28914

5. Drain water from air tank by opening drain valve (counter-clockwise) on

bottom of tank. NOTE: Tilt tank to drain tank completely.

Water will condense in the air tank. If not drained, water

will corrode and weaken the air tank causing a risk of air

tank rupture.

6. After the water has been drained, close the drain valve (clockwise). The air

compressor can now be stored.

NOTE: If drain valve is plugged, release all air pressure. The valve can then be

removed, cleaned, then reinstalled.

Oil

Drain tank to release air pressure before removing the

dipstick or oil drain plug.

Compressor head and cylinder sleeve are very hot. Do not

touch.

Checking

1. Set the On/Auto/Off lever to “OFF”.

2. Remove dipstick (A) and check oil on dipstick for visual signs of

contaminants (water, dirt, etc).

Make sure air vent (C)

in dipstick is free from

debris. If air vent is blocked pressure

can build in crankcase causing damage

to air compressor and possible personal

injury.

3. Wipe oil from dipstick.

4. Replace dipstick and allow oil to

collect on dipstick.

5. Remove dipstick and check oil level

on dipstick, + mark indicates full and

the - mark indicates add oil. If oil level

is below - mark, slowly add oil until it

reaches the + (full) mark on the dipstick.

NOTE: Use an oil specifically formulated for use in an air compressor, such as

Porter-Cable PAS1 air compressor oil. Oil may be found at the store where the

air compressor was purchased.

6. Replace dipstick (A).

Changing

1. Set the On/Auto/Off lever to “OFF”.

2. Remove the dipstick (A).

3. Remove the oil drain plug (B) and drain oil into a suitable container.

4. Replace the oil drain plug (B).

+

-

A

C

B

(+)Full

(-)Add

18- ENG

D28914

Air Filter - Inspection and Replacement

Hot surfaces. Risk of burn. Compressor heads are

exposed when filter cover is removed. Allow compressor

to cool prior to servicing.

A dirty air filter will not allow the compressor to operate at full capacity. Keep

the air filter clean at all times.

1. Remove the air filter cover.

2. Remove the air filter from filter cover.

IMPORTANT: Do not operate the compressor with the air filter removed.

3. Place new air filter into filter cover. Refer to the “Repair Parts” for the

correct part number.

4. Replace air filter cover and lock into place.

5. Slowly fill crankcase with oil. Crankcase capacity is 8 fluid ounces (236.6

ml). Oil level should be at the + (full) mark on the dipstick.

Overfilling with oil will cause premature compressor

failure. Do not overfill.

6. Replace dipstick (A).

Motor

The motor has an automatic reset thermal overload protector. If the motor

overheats for any reason, the overload protector will shut off the motor. The

motor must be allowed to cool down before restarting. The compressor will

automatically restart after the motor cools.

If the overload protector shuts the motor off frequently, check for a possible

voltage problem. Low voltage can also be suspected when:

1. The motor does not get up to full power or speed.

2. Fuses blow out when starting the motor; lights dim and remain dim when

motor is started and is running.

19- ENG

D28914

Unit cycles automatically when power is on. When doing

Maintenance, you may be exposed to voltage sources,

compressed air or moving parts. Personal injuries can occur. Before

performing any Maintenance or repair, unplug the compressor and bleed

off all air pressure.

SERVICE AND ADJUSTMENTS

ALL MAINTENANCE AND REPAIR OPERATIONS NOT LISTED MUST BE

PERFORMED BY TRAINED SERVICE TECHNICIAN.

Before servicing:

• Unplug or disconnect electrical supply to the air compressor.

• Bleed tank of pressure.

• Allow the air compressor to cool.

To Replace or Clean Check Valve

1. Release all air pressure from air tank. See “To Drain Tank” in the

Maintenance section.

2. Unplug outfit.

NOTE: If needed the top panel may be removed to make parts accessible.

3. Using an adjustable wrench loosen

outlet tube nut at air tank and pump.

Carefully move outlet tube away from

check valve.

4. Using an adjustable wrench loosen

pressure relief tube nut at air tank

and pressure switch. Carefully move

pressure relief tube away from check

valve.

5. Unscrew the check valve (turn

counterclockwise) using a 7/8” open

end wrench. Note the orientation for

reassembly.

6. Unscrew elbow fitting from the check valve (turn counterclockwise) using

an adjustable wrench. Note the orientation of the elbow fitting for

reassembly.

7. Using a screwdriver, carefully

push the valve disc up and

down. NOTE: The valve disc

should move freely up and

down on a spring which holds

the valve disc in the closed

position. If not, the check valve

needs to be cleaned or replaced.

8. Clean or replace the check valve. A solvent, such as paint or varnish

remover can be used to clean the check valve.

9. Apply sealant to the check valve threads. Reinstall the check valve and

elbow fitting (turn clockwise).

10. Replace the pressure release tube. Tighten nut.

11. Replace the outlet tube and tighten nut.

12. Perform the Break-in Procedure. See “Break-in Procedure” in the

Operation section.

Pressure Relief Tube

Check

Valve

Nuts

Outlet Tube

Elbow Fitting

In closed position

disc is visible.

In open position

nothing is visible.

Screwdriver

20- ENG

D28914

STORAGE

Before you store the air compressor, make sure you do the following:

1. Review the "Maintenance" section on the preceding pages and perform

scheduled maintenance as necessary.

2. Set the On/Auto/Off lever to "OFF".

3. Turn the regulator counterclockwise and set the outlet pressure to zero.

4. Remove the air tool or accessory.

5. Pull ring on safety valve allowing air to bleed from the tank until tank

pressure is approximately 20 psi. Release safety valve ring.

6. Drain water from air tank by opening drain valve on bottom of tank.

Water will condense in the air tank. If not drained, water

will corrode and weaken the air tank causing a risk of air

tank rupture.

7. After the water has been drained, close the drain or drain valve.

NOTE: If drain valve is plugged, release all air pressure. The valve can then be

removed, cleaned, then reinstalled.

8. Wrap electrical cord onto the cord

wrap as shown.

9. Protect the air hose from damage

(such as being stepped on or run over).

10. Store the air compressor in a clean and

dry location.

La page charge ...

Porter-Cable JOB BOSS C3550 Manuel utilisateur

Ce manuel convient également à

Porter-Cable JOB BOSS C3550 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents