Aruba AP-515 Guide d'installation

Marque: Aruba

Modèle: AP-515

Catégorie: Points d'accès WLAN

Taper: Guide d'installation

Ce manuel convient également à

Aruba 510 Series Campus Access Points

Installation Guide

Rev04 | June 2019 1

The Aruba 510 Series Campus Access Points (AP-514 and AP-515) are high-performance, multi-radio wireless

devices that can be deployed in either controller-based (ArubaOS) or controllerless (Aruba Instant) network

environments. These access points deliver high performance concurrent 2.4 GHz and 5 GHz 802.11ax Wi-Fi

functionality with MIMO radios (2x2 in 2.4 GHz, 4x4 in 5 GHz), while also supporting legacy 802.11a/b/g/n/ac

wireless services.

Ethernet ports located on the back of this access points are used to connect the device to the wired networking

infrastructure and to provide (802.3at class 4) PoE power to the device.

In addition to both Wi-Fi radios, these APs also incorporate a Bluetooth Low Energy (BLE) and Zigbee radio,

supporting a variety of use-cases and services, such as locationing and IoT.

A mount kit (sold separately) is needed to mount the AP. Make sure to purchase the correct mount kit for the

intended deployment of the AP.

Package Contents

 Aruba 510 Series Campus Access Point (with a pre-installed mount bracket)

Hardware Overview

The following sections outline the hardware components of the 510 Series access points.

Figure 1 AP-515 Front View

The AP mount bracket attaches to a variety of mount kits (sold separately).

Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including

the original packing materials. Use these materials to repack and return the unit to the supplier if needed.

2 Aruba 510 Series Campus Access Points | Installation Guide

Figure 2 LEDs (AP-515 shown)

Figure 3 AP-514 Front View

External Antenna Connectors

The AP-514 access points are equipped with four external antenna connectors located on the front

corners of the access point (see

Figure 3). Antenna ports A0 and A1 (corresponding with radio chains 0

and 1), are used for both radios and bands (RF signals are diplexed), while antenna ports A2 and A3

(corresponding with radio chains 2 and 3) are used for the 5 GHz radio only.

Aruba 510 Series Campus Access Points | Installation Guide 3

LEDs

The LED displays located on the front panel of the access point indicate the following functions:

System Status

The System Status LED indicates the operating condition of the access point, See Table 1.

Table 1 System Status LED

Radio Status

The Radio Status LED indicates the operating mode of the access point’s radios. See Table 2.

Table 2 Radio Status LEDs

External antennas for this device must be installed by an Aruba Certified Mobility Professional (ACMP) or other

Aruba-certified technician, using manufacturer-approved antennas only.

The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the

regulatory limit set by the host country/domain.

Installers are required to record the antenna gain for this device in the system management software. A list of

approved antennas can be found at: http://www.arubanetworks.com/assets/og/OG_AP-510Series.pdf.

Les antennes externes pour cet appareil doivent être installées par un professionnel de la mobilité certifié Aruba

(ACMP) ou un autre technicien certifié Aruba, en utilisant uniquement des antennes approuvées par le fabricant.

Les niveaux équivalents de puissance à rayonnement isotrope (EIRP) pour tous les périphériques d'antenne

externe ne doivent pas dépasser la limite réglementaire définie par le pays hôte / domaine.

Les installateurs doivent enregistrer le gain d'antenne pour cet appareil dans le logiciel de gestion du système.

Une liste d'antennes approuvées peut être trouvée à http://www.arubanetworks.com/assets/og/OG_AP-

510Series.pdf.

Color/State Meaning

Off Device Powered off

Green- solid Device ready, fully functional, no network restrictions

Green- blinking

1. Blinking: one second on, one second off, 2 seconds cycle.

Device booting, not ready

Green- flashing

2. Flashing: mostly on, fraction of a second off, 2 seconds cycle.

Device ready, fully functional, either uplink negotiated in sub-optimal speed

(<1Gbps)

Amber- solid Device ready, restricted power mode (limited PoE power available, or IPM

restrictions applied), no network restrictions

Amber- flashing Device ready, restricted power mode (limited PoE power available, or IPM

restrictions applied), uplink negotiated in sub-optimal speed

Red System error condition - Immediate attention required

Color/State Meaning

Off Device powered off, or both radios disabled

Green- solid Both radios enabled in access mode

4 Aruba 510 Series Campus Access Points | Installation Guide

LED Display Settings

The LEDs have three operating modes that can be selected in the system management software:

 Default mode: Refer to Table 1and Table 2

 Off mode: LEDs are off

 Blink mode: LEDs blink green (synchronized)

Force the LEDs into off mode and back to software defined mode by pressing the reset button for a short

duration.

Figure 4 AP-515 Rear View

Cable Guide

The cable guide on the rear of the access point is used to organize cables, as shown in Figure 5. The use of the

cable guide is optional and does not support all types of cables and plugs.

Green- blinking One radio enabled in access mode, other disabled

Amber- solid Both radios enabled in monitor mode

Amber- blinking One radio enabled in monitor mode, other disabled

Green/Amber-

alternating

Green: one radio in access mode

Amber: one radio in monitor mode

1. Alternating: one second each color, 2 seconds cycle.

Color/State Meaning

Pressing the reset button for longer than 10 seconds may cause the AP to reset and return to factory default

state.

Kensington

Lock Slot

ConsoleReset USB 2.0 Interface

DC Jack

Aruba 510 Series Campus Access Points | Installation Guide 5

Figure 5 Cable Guide

To remove the cable guide, perform the following steps:

1. Insert the flat head of a screwdriver into the slot on the cable guide. Press the screwdriver down to disengage

the buckle on underside of the tab, as shown in Figure 6.

2. Push the cable guide towards the chassis as shown in Figure 6, the cable guide will slide out.

Figure 6 Removing Cable Guide

Bluetooth Low Energy and Zigbee Radio

510 Series access points are equipped with an integrated BLE and Zigbee radio that provide the following

capabilities:

 location beacon applications

 wireless console access

 IOT gateway applications

Console Port

The console port is a Micro-B connector located on the back of this device. A proprietary serial adapter cable (AP-

Step2: push

Step1: Insert

screwdriver into this

slot and press down

6 Aruba 510 Series Campus Access Points | Installation Guide

CBL-SERU) is needed to use this interface. It is sold separately to connect the AP to a serial terminal or a laptop

for direct local management (a standard USB cable cannot be used for this interface). For pin-out details, refer to

Figure 7.

Figure 7 Micro-B Port Pin-out

Ethernet Ports

The Aruba 510 Series access points are equipped with two Ethernet ports (E0 and E1), shown in Figure 4.

 E0 port: 100/1000/2500BaseT auto-sensing MDI/MDX wired RJ45 network connectivity port

 E1 port: 100/1000BaseT auto-sensing MDI/MDX wired RJ45 network connectivity port

Both ports are compliant with 802.3ab 1000BaseT Gigabit Ethernet standard, while E0 also supports both

NBase-T and 802.3bz standards for 2.5bps Ethernet. The E0 port supports 802.3af, 802.3at and 802.3bt to accept

power from a POE source, such as a PoE midspan injector, or a network switch.

Kensington Lock Slot

The 510 Series is equipped with a Kensington lock slot for additional physical security.

USB 2.0 Interface

The top of this access point is equipped with a USB-A port that is compatible with selected cellular modems and

other peripherals. When active, this port can supply up to 5W/1A to a connected device.

Reset Button

The reset button located on the bottom of the device can be used to reset the access point to factory default

settings or turn off/on the LED display.

There are two ways to reset the access point to factory default settings:

Reset the AP during normal operation

press and hold down the reset button using a small, narrow object such as a paper clip for more than 10

seconds during normal operation.

Reset the AP while powering up

1. Press and hold down the reset button using a small, narrow object such as a paper clip while the access point

is not powered on (either via DC power or PoE).

2. Connect the power supply (DC or PoE) to the access point while the reset button is being held down.

3. Release the reset button on the access point after 15 seconds.

To turn off/on the LED display, press and release the reset button using a small, narrow object, such as a

paperclip for less than 10 seconds during normal operation of the access point.

Power

E0 port supports PoE-in (AP is a PoE-PD device), allowing the device to draw power from compliant PoE power

sources. If PoE is not available, a proprietary AP-AC-12V30B power adapter (sold separately) can be used to

power the access point. When both PoE and DC power sources are available, the DC power source takes

precedence. In that case, the access point simultaneously draws a minimal current from the PoE source. In the

event that the DC source fails, the access point switches to the PoE sources.

The Intelligent Power Monitoring (IPM) feature may also be used to manage the power consumption

preferences for this device. When enabled, the user may enable/disable power restrictions for the access point

using Aruba’s AP management software.

1: N/C

2: RXD

3: TXD

4: GND

5: GND

Aruba 510 Series Campus Access Points | Installation Guide 7

Table 3 lists operational restrictions when the access point is powered by different power options.

Table 3 Power Options and Operational Restrictions

Before You Begin

Refer to the sections below before beginning the installation process.

Pre-Installation Checklist

Before installing your Aruba 510 Series access point, be sure that you have the following (not included with the

AP):

 A mount kit compatible with the AP and mount surface

 Cat5E or better UTP cable with network access

 One or more external antennas (when using the AP-514)

 (Optional) a compatible 12V AC-to-DC power adapter with power cord

 (Optional) a compatible PoE midspan injector with power cord

 (Optional) a compatible snap-on front cover (for easy aesthetic customization)

 (Optional) an AP-CBL-SERU console cable

Also make sure that (at least) one of the following network services is supported:

 Aruba Discovery Protocol (ADP)

 DNS server with an “A” record

 DHCP Server with vendor-specific options

Identifying Specific Installation Locations

Use the access point placement map generated by Aruba RF Plan software application to determine the proper

installation location(s). Each location should be as close as possible to the center of the intended coverage area

and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/

interference sources will impact RF propagation and should be accounted for during the planning phase and

adjusted for in RF plan.

Power Source IPM Restrictions

DC power n/a No restrictions, all capabilities available

PoE 802.3bt n/a No restrictions, all capabilities available

PoE 802.3at n/a No restrictions, all capabilities available

PoE 802.3af enabled All capabilities available (features may be disabled per IPM

configuration)

PoE 802.3af disabled Not supported

FCC Statement: Improper termination of access points installed in the United States configured to non-US

model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or intentional

violation may result in a requirement by the FCC for immediate termination of operation and may be subject to

forfeiture (47 CFR 1.80).

The Aruba 510 Series access point is designed in compliance with governmental requirements so that only

authorized network administrators can change the settings. For more information about access point

configuration, refer to the AP Software Quick Start Guide.

Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in

improper operation. If such use is necessary, this equipment and the other equipment should be observed to

verify that they are operating normally.

8 Aruba 510 Series Campus Access Points | Installation Guide

Identifying Known RF Absorbers/Reflectors/Interference Sources

Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation

phase is critical. Make sure that these sources are taken into consideration when you attach an access point to its

fixed location.

RF absorbers include:

 Cement/concrete—Old concrete has high levels of water dissipation, which dries out the concrete, allowing

for potential RF propagation. New concrete has high levels of water concentration in the concrete, blocking

RF signals.

 Natural Items—Fish tanks, water fountains, ponds, and trees

 Brick

RF reflectors include:

 Metal Objects—Metal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh windows,

blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets.

 Do not place an access point between two air conditioning/heating ducts. Make sure that access points are

placed below ducts to avoid RF disturbances.

RF interference sources include:

 Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones)

 Cordless headset such as those used in call centers or lunch rooms

Access Point Installation

the Aruba 510 Series access points are designed for ceiling or wall mounted deployments. Several optional

mount kits are available to attach the Aruba 510 Series access point to a variety of surfaces. These mount kits are

available as accessories and must be ordered separately. Refer to the online ordering guide at http://

www.arubanetworks.com/assets/og/OG_AP-510Series.pdf

Portable RF communications equipment (including peripherals such as antenna cables and external antennas)

should be used no closer than 30 cm (12 inches) to any part of the access point. Otherwise, degradation of the

performance of this equipment could result.

RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This

equipment should be installed and operated with a minimum distance of 13.78 inches (35cm) between the

radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter.

Déclaration sur les limites d'exposition aux radiofréquences : cet équipement est conforme aux limites

d'exposition aux rayonnements radioélectriques spécifiées par la FCC. Il doit être installé et utilisé à une distance

minimale de 35 cm par rapport à votre corps pour les fréquences de 2,4 et 5 GHz. Cet émetteur-récepteur ne

doit pas être utilisé ou situé à proximité d'autres antennes ou émetteurs-récepteurs.

All Aruba access points should be professionally installed by an Aruba-Certified Mobility Professional (ACMP).

The installer is responsible for ensuring that grounding is available and meets applicable national and electrical

codes. Failure to properly install this product may result in physical injury and/or damage to property.

Tous les points d'accès Aruba doivent impérativement être installés par un professionnel agréé. Ce dernier doit

s'assurer que l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques

nationaux en vigueur. Le fait de ne pas installer correctement ce produit peut entraîner des blessures

corporelles et / ou des dommages matériels.

The installer is responsible for securing the access point onto the ceiling tile rail. Failure to properly install this

product may result in physical injury and/or damage to property.

Use of accessories, transducers and cables other than those specified or provided by the manufacturer of this

equipment could result in increased electromagnetic emissions or decreased electromagnetic immunity of this

equipment and result in improper operation.

Aruba 510 Series Campus Access Points | Installation Guide 9

Software

For instructions on choosing operating modes and initial software configuration, refer to the AP Software Quick

Start Guide.

Verifying Post-Installation Connectivity

The integrated LED on the access point can be used to verify that the access point access point is receiving power

and initializing successfully (see Table 1-Table 2). Refer to the AP Software Quick Start Guide for further details

on verifying post-installation network connectivity.

Electrical and Environmental Specifications

For additional specifications on this product, please refer to the product data sheet at www.arubanetworks.com

Electrical

 Ethernet:

 E0 port: 100/1000/2500BaseT auto-sensing MDI/MDX wired RJ45 network connectivity port

 E1 port: 100/1000BaseT auto-sensing MDI/MDX wired RJ45 network connectivity port

 Power:

 12V DC power interface, support powering through AC-to-DC power adapter (AP-AC-12V30B)

 Power over Ethernet (PoE): 802.3af, 802.3at or 802.3bt compliant source

Environmental

 Operating:

 Temperature: 0°C to +50°C (+32°F to +122°F)

 Humidity: 5% to 93% non-condensing

 Storage and transport:

 Temperature: -40°C to +70°C (-40°F to +158°F)

 Humidity: 5% to 93% non-condensing

Regulatory Model Name

The following regulatory model numbers (RMN) apply to the 510 Series:

 AP-514 RMN: APIN0514

Aruba access points are classified as radio transmission devices, and are subject to government regulations of

the host country. The network administrator(s) is/are responsible for ensuring that configuration and operation

of this equipment is in compliance with their country’s regulations. For a complete list of approved channels in

your country, refer to the Aruba Downloadable Regulatory Table at support.arubanetworks.com.

Japan – Please disable the 11ax (High Efficiency) operation until such time it is confirmed that has Japan

approved a regulatory framework for 11ax.

If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed,

with an output rated 12V DC, minimum 0.75A, marked “LPS” and “Class 2,” and suitable for plugging into a

standard power receptacle in the US and Canada.

The Aruba 510 Series access points are for indoor use only. The access point, AC adapter, and all connected

cables are not designed for outdoor use.

This device is intended for stationary use in partly temperature controlled weather-protected environments.

10 Aruba 510 Series Campus Access Points | Installation Guide

 AP-515 RMN: APIN0515

Safety and Regulatory Compliance

Federal Communication Commission

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the manufacturer’s instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

 Consult the dealer or an experienced radio or TV technician for help.

Industry Canada

This Class B digital apparatus meets all of the requirements of the Canadian Interference-Causing Equipment

Regulations.

In accordance with Industry Canada regulations, this radio transmitter and receiver may only be used with an

antenna, the maximum type and gain of which must be approved by Industry Canada. To reduce potential radio

interference, the type of antenna and its gain shall be chosen so that the equivalent isotropic radiated power

(EIRP) does not exceed the values necessary for effective communication.

This device complies with Industry Canada's license-exempt RSS regulations. Operation of this device is subject

to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation.

When operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the

potential for harmful interference with co-channel Mobile Satellite Systems.

Déclaration d’Industrie Canada

Conformément aux réglementations d’Industrie Canada, cet émetteur-récepteur radio doit être utilisé

RF Radiation Exposure Statement: This equipment complies with RF radiation exposure limits. This

equipment should be installed and operated with a minimum distance of 13.78 inches (35cm) between the

radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter.

Déclaration de la concernant l’exposition aux rayonnements à fréquence radioélectrique (FR): Cet

appareil est conforme aux limites d’exposition aux rayonnements FR établies. Il doit être installé et utilisé à une

distance minimale de 35 cm (13,78 pouces) entre le radiateur et votre corps, qu’il opère sur la bande 2,4 GHz

ou 5 GHz. Cet émetteur ne doit pas être installé ou utilisé à proximité immédiate d’une autre antenne ni d’un

autre transmetteur.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could

void the user’s authority to operate this equipment.

Toute modification effectuée sur cet équipement sans l'autorisation expresse de la partie responsable de la

conformité est susceptible d'annuler son droit d'utilisation.

Aruba 510 Series Campus Access Points | Installation Guide 11

uniquement avec une antenne dont le type et le gain maximal doivent être approuvés par Industrie Canada.

Pour réduire les interférences radio potentielles, le type d’antenne et son gain doivent être choisis de façon à ce

que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas les valeurs nécessaires à une

communication efficace.

Ce périphérique est conforme aux règlements RSS exempts de licence d’Industrie Canada. L’utilisation de ce

périphérique est soumise aux deux conditions suivantes : (1) ce périphérique ne doit pas provoquer

d’interférences, et (2) ce périphérique doit accepter toute interférence, y compris les interférences susceptibles

de provoquer un dysfonctionnement.

En cas d'utilisation dans la plage de fréquences de 5,15 à 5,25 GHz, cet appareil doit uniquement être utilisé en

intérieur afin de réduire les risques d'interférence avec les systèmes satellites mobiles partageant le même

canal.

Canadian Caution

This radio transmitter model APIN0514/APIN0515 has been approved by Industry Canada to operate with the

antenna typeslisted in the table in the online ordering guide (link provided below) with the maximum

permissible gain indicated. Antenna types not included in this list, having a gaingreater than the maximum gain

indicated for that type, are strictly prohibited for usewith this device.

http://www.arubanetworks.com/assets/og/OG_AP-510Series.pdf

Le présent transmetteur radio modèle APIN0514/APIN0515 a été approuvé par Industrie Canada pour

fonctionner avec les types d'antennesindiqués dans le tableau du guide de commande en ligne (lien fourni ci-

dessous) avec le gain permissible maximum indiqué. Il est strictement défendu d'utiliser avec cet appareil les

types d'antennes non inclus dans cette liste, ayant un gain supérieur au gain maximumindiqué pour ce type.

http://www.arubanetworks.com/assets/og/OG_AP-510Series.pdf

European Union Regulatory Conformance

The Declaration of Conformity made under Radio Equipment Directive 2014/53/EU is available for

viewing at: www.hpe.com/eu/certificates. Select the document that corresponds to your device’s model number

as it is indicated on the product label

This radio transmitter model has been approved to operate with the antenna types listed in the online ordering

guide (link provided below) with the maximum permissible gain indicated. Antenna types not included in this list,

having a greater gain than the maximum gain indicated for the type, are strictly prohibited for use with this

device. Compliance is only assured if the Aruba approved accessories as listed in the ordering guide are used.

http://www.arubanetworks.com/assets/og/OG_AP-510Series.pdf

Wireless Channel Restrictions

5150-5350MHz band is limited to indoor only in the following countries; Austria (AT), Belgium (BE), Bulgaria (BG),

Croatia (HR), Cyprus (CY), Czech Republic (CZ), Denmark (DK), Estonia (EE), Finland (FI), France (FR), Germany (DE),

Greece (GR), Hungary (HU), Iceland (IS), Ireland (IE), Italy (IT), Latvia (LV), Liechtenstein (LI), Lithuania (LT),

Luxembourg (LU), Malta (MT), Netherlands (NL), Norway (NO), Poland (PL), Portugal (PT), Romania (RO), Slovakia

(SK), Slovenia (SL), Spain (ES), Sweden (SE), Switzerland (CH), Turkey (TR), United Kingdom (UK)

Radio Frequency Range MHz Max EIRP

BLE/Zigbee 2402-2480 9 dBm

Wi-Fi

2412-2472 20 dBm

5150-5250 23 dBm

5250-5350 23 dBm

5470-5725 30 dBm

5725-5850 14 dBm

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide/

Instant User Guide for details on restrictions.

12 Aruba 510 Series Campus Access Points | Installation Guide

Medical

1. Equipment not suitable for use in the presence of flammable mixtures.

2. Connect to only IEC 60950-1 or IEC 60601-1 certified products and power sources. The end user is

responsible for the resulting medical system complies with the requirements of IEC 60601-1.

3. Wipe with a dry cloth, no additional maintenance required.

4. No serviceable parts, the unit must be sent back to the manufacturer for repair.

5. No modifications are allowed without Aruba approval.

Brazil

Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência

em sistemas devidamente autorizados.

Japan

México

La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o

dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debeaceptar cualquier interferencia,

incluyendo la que pueda causar su operación no deseada.

This device is intended for indoor use in professional healthcare facilities.

This device has no IEC/EN60601-1-2 essential performance.

Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result

in improper operation. If such use is necessary, this equipment and the other equipment should be observed

to verify that they are operating normally.

Compliance is based on the use of Aruba approved accessories. Refer to the ordering guide for this access

point at http://www.arubanetworks.com/assets/og/OG_AP-510Series.pdf.

Use of accessories, transducers and cables other than those specified or provided by the manufacturer of this

equipment could result in increased electromagnetic emissions or decreased electromagnetic immunity of this

equipment and result in improper operation.

Portable RF communications equipment (including peripherals such as antenna cables and external antennas)

should be used no closer than 30 cm (12 inches) to any part of the access point. Otherwise, degradation of the

performance of this equipment could result.

Aruba 510 Series Campus Access Points | Installation Guide 13

Este equipo ha sido diseñado para operar con las antenas que enseguida se enlistan, en los puntos 3 de: https:/

/www.arubanetworks.com/assets/og/OG_AP-510Series.pdf y para una ganancia máxima de antena de 8.5 dBi.

El uso con este equipo de antenas no incluidas en esta lista o que tengan una ganancia mayor que 8.5 dBi

quedan prohibidas. La impedancia requerida de la antena es de 50 ohms.

Morocco

Нормативные требования Евразийского Экономического Союза

Russia

HPE Russia: ООО "Хьюлетт Паккард Энтерпрайз" Российская Федерация, 125171, г.

Москва, Ленинградское шоссе, 16А, стр.3, Телефон: +7 499 403 4248 Факс: +7 499 403

4677

'HPE Belarus': ИООО «Хьюлетт-Паккард Бел», Республика Беларусь, 220030, г. Минск,

ул. Интернациональная, 36-1, Телефон/факс: +375 17 392 28 20

'HPE Kazakhstan': TOO «Хьюлетт-Паккард (К)», Республика Казахстан, 050040, г.

Алматы, Бостандыкский район, проспект Аль-Фараби, 77/7, Телефон/факс: + 7 727 355 35 50

Kazakhstan

ЖШС "Хьюлетт Паккард Энтерпрайз" Ресей Федерациясы, 125171, Мәскеу, Ленинград тас жолы, 16A блок

3, Телефон: +7 499 403 4248 Факс: +7 499 403 4677

«HEWLETT-PACKARD Bel» ЖШС, Беларусь Республикасы, 220030, Минск қ., Интернациональная көшесі, 36/

1, Телефон/факс: +375 17 392 28 20

ЖШС «Хьюлетт-Паккард (К)», Қазақстан Республикасы, 050040, Алматы к., Бостандык ауданы, Әл-Фараби

даңғ ылы, 77/7, Телефон/факс: +7 (727) 355 35 50

Taiwan

第十二條

　　經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功

能。

第十四條

　　低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使

用。

　　前項合法通信，指依電信法規定作業之無線電通信。

　　低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

Contacting Support

Table 4

Contact Information

Main Site arubanetworks.com

Support Site support.arubanetworks.com

Airheads Social Forums and Knowledge

Base

community.arubanetworks.com

14 Aruba 510 Series Campus Access Points | Installation Guide

Open Source Code

This product includes code licensed under the GNU General Public License, the GNU Lesser General Public

License, and/or certain other open source licenses. A complete machine-readable copy of the source code

corresponding to such code is available upon request. This offer is valid to anyone in receipt of this information

and shall expire three years following the date of the final distribution of this product version by Hewlett Packard

Enterprise Company. To obtain such source code, send a check or money order in the amount of US $10.00 to:

Hewlett Packard Enterprise Company

Attn: General Counsel

3000 Hanover Street

Palo Alto, CA 94304

USA

Warranty

This hardware product is protected by an Aruba warranty. For more details visit www.hpe.com/us/en/

support.html

North American Telephone 1-800-943-4526 (Toll Free)

1-408-754-1200

International Telephones arubanetworks.com/support-services/contact-support/

Software Licensing Site hpe.com/networking/support

End of Support information arubanetworks.com/support-services/end-of-life-products/end-of-

life-policy/

Security Incident Response Team (SIRT) Site: arubanetworks.com/support-services/security-bulletins/

Email: [email protected]

Table 4 Contact Information

Aruba AP-515 Guide d'installation

Marque: Aruba

Modèle: AP-515

Catégorie: Points d'accès WLAN

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Aruba AP-515 Installation guide
dansk: Aruba AP-515 Installationsvejledning

Aruba AP-515 Guide d'installation

Ce manuel convient également à

Aruba AP-515 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents