Alto-Shaam 300-CW Installation Operation & Maintenance

Marque: Alto-Shaam

Modèle: 300-CW

Catégorie: Chauffe-plats

Taper: Installation Operation & Maintenance

Ce manuel convient également à

W164 N9221 Water Street • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 USA

PHONE: 262.251.3800 • 800.558.8744

USA/CANADA

FAX: 262.251.7067 • 800.329.8744

U.S.A. ONLY

www.alto-shaam.com

PRINTED IN U .S . A .

MN-36033 (REV. 0) • 07/14

s).34!,,!4)/.

s/0%2!4)/.

s-!).4%.!.#%

-odels:

#7

#7

#7

#7

#7

#7

100-CW

300-CW

500-CW

Consult

instructions

for installation

and use.

#OLD&OOD$ROP)N7ELLS

%LECTRIC

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>

Delivery ..................................1

Unpacking................................1

Safety Procedures and Precautions ............2

Installation

Installation Requirements .................. 3

Installation and Leveling ...................4

Options & Accessories ....................5

Dimensions.............................5

Rough Cut Openings ..................... 8

Product/Pan Capacity ....................8

Louver and Vent Housing Instructions ........ 9

Rotation of Compressor Instructions ........ 10

Electrical Specifications .................. 11

Electrical Connection .................... 11

Plumbing Connection .................... 11

Installation Checklist .................... 12

Operating Instructions

Operating Instructions ................... 13

Care and Cleaning

Cleaning and Preventative Maintenance...... 14

Protecting Stainless Steel Surfaces ......... 14

Cleaning Agents ........................ 14

Cleaning Materials ...................... 14

Care and Cleaning ...................... 15

Sanitation ............................. 16

Preventative Maintenance................. 17

Service

Trouble Shooting ....................... 18

Service Parts - Exterior .................. 19

Wire Diagrams

Always refer to the wire diagram(s) included with

the unit for most current version.

Warranty

Transportation Damage and Claims ..Back Cover

Limited Warranty ................Back Cover

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊ£

DELIVERY

This Alto-Shaam appliance has been

thoroughly tested and inspected to ensure only

the highest quality unit is provided. Upon

receipt, check for any possible shipping damage

and report it at once to the delivering carrier.

See Transportation Damage and Claims section

located in this manual.

This appliance, complete with unattached

items and accessories, may have been delivered

in one or more packages. Check to ensure that all

standard items and options have been received

with each model as ordered.

Save all the information and instructions

packed with the appliance. Complete and return

the warranty card to the factory as soon as

possible to ensure prompt service in the event of a

warranty parts and labor claim.

This manual must be read and understood

by all people using or installing the equipment

model. Contact the Alto-Shaam Tech Team Service

Department if you have any questions concerning

installation, operation, or maintenance.

NOTE: All claims for warranty must include the

full model number and serial number of

the unit.

UNPACKING

1. Carefully remove the

appliance from the

carton or crate.

NOTE: Do not discard the

carton and other

packaging material

until you have

inspected the unit

for hidden damage

and tested it for

proper operation.

2. Read all instructions in this manual carefully

before initiating the installation of this appliance.

DO NOT DISCARD THIS MANUAL.

This manual is considered to be part of the

appliance and is to be provided to the owner

or manager of the business or to the person

responsible for training operators. Additional

manuals are available from the Alto-Shaam

Tech Team Service Department.

3. Remove all protective plastic film, packaging

materials, and accessories from the appliance

before connecting electrical power. Store any

accessories in a convenient place for future use.

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊÓ

CAUTION

Used to indicate the presence of a hazard that

can or will cause minor personal injury, property

damage, or a potential unsafe practice if the

warning included with this symbol is ignored.

CAUTION

Used to indicate the presence of a

hazard that can or will cause minor or

moderate personal injury or property

damage if the warning included with

this symbol is ignored.

DANGER

Used to indicate the presence of

a hazard that WILL cause severe

personal injury, death, or substantial

property damage if the warning

included with this symbol is ignored.

WARNING

Used to indicate the presence of

a hazard that CAN cause personal

injury, possible death, or major

property damage if the warning

included with this symbol is ignored.

1. This appliance is intended to cook, hold

or process foods for the purpose of human

consumption. No other use for this appliance is

authorized or recommended.

2. This appliance is intended for use in commercial

establishments where all operators are

familiar with the purpose, limitations, and

associated hazards of this appliance. Operating

instructions and warnings must be read and

understood by all operators and users.

3. Any troubleshooting guides, component views,

and parts lists included in this manual are for

general reference only and are intended for use

by qualified technical personnel.

4. This manual should be considered a permanent

part of this appliance. This manual and all

supplied instructions, diagrams, schematics,

parts lists, notices, and labels must remain with

the appliance if the item is sold or moved to

another location.

NOTE: Used to notify personnel of

installation, operation, or

maintenance information that is

important but not hazard related.

SAFETY PROCEDURES

AND PRECAUTIONS

Knowledge of proper procedures is essential to the

safe operation of electrically and/or gas energized

equipment. In accordance with generally accepted

product safety labeling guidelines for potential

hazards, the following signal words and symbols

may be used throughout this manual.

Used to indicate that referral to

operating instructions is a mandatory

action. If not followed the operator

could suffer personal injury.

Used to indicate that referral to

operating instructions is recommended

to understand operation of equipment.

NOTE

For equipment delivered for use

in any location regulated by the

following directive:

DO NOT DISPOSE OF ELECTRICAL

OR ELECTRONIC EQUIPMENT WITH

OTHER MUNICIPAL WASTE.

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊÎ

INSTALLATI ON

S I T E INSTALLATI ON

The Alto-Shaam Cold Well must be installed in a location

that will permit it to function for its intended purpose and to

allow adequate clearance for ventilation, proper cleaning, and

maintenance access.

DANGER

IMPROPER INSTALLATION,

ALTERATION, ADJUSTMENT,

SERVICE, OR MAINTENANCE COULD

RESULT IN SEVERE INJURY, DEATH,

OR CAUSE PROPERTY DAMAGE.

READ THE INSTALLATION,

OPERATING AND MAINTENANCE

INSTRUCTIONS THOROUGHLY

BEFORE INSTALLING OR SERVICING

THIS EQUIPMENT.

CAUTION

TO PREVENT PERSONAL INJURY,

USE CAUTION WHEN MOVING OR

LEVELING THIS APPLIANCE.

DANGER

DO NOT store or use gasoline or other

ﬂ ammable vapors or liquids in the

vicinity of this or any other appliance.

inStaLLation rEQuirEMEntS

Counter top material must be water resistant.

Distance of 3/4" (19mm) or more between top rims of wells to

ensure easy cleaning.

Must be installed level.

Must not be installed in any area where it may be directly affected

by steam, grease, dripping water, high temperatures, or any other

severely adverse conditions.

Must not be installed under a hood.

Avoid installation under a 4-way ceiling diffuser.

Outdoor use is not recommended.

Drain or catch basin is required.

LED lighting is recommended for overhead lighting

cLEarancE rEQuirEMEntS

4" (102mm) in front of dual air movement louver

ELEctricaL

VOLTAGE PHASE CYCLE/HZ AMPS KW PLUG CONFIG.

115 1 60 5.0 .6 NEMA 5-15P

15A-125V PLUG

9' (229mm) LONG CORD

5-Year Limited

Warranty on

self-contained

compressor

Effective from date of

shipment. (EXCLUDES LABOR)

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊ{

S I T E INSTALLATI ON

1. The cold well must be installed on a stable and

level surface - free of vibration and suitably

strong enough to support the combined weights

of the unit plus the maximum product load

weight.

2. DO NOT install this appliance in any area

where it may be affected by any adverse

conditions. Avoid placing the unit in direct

sunlight, near heat generating equipment

such as ovens, ranges, heaters, fryers, steam

kettles, dripping water, high temperatures, or

any other severely adverse conditions. Avoid

locating in an unheated room or where the room

temperature may drop below 55°F (13°C) or

above 86°F (30°C).

3. Once the drop in unit is installed into the

counter it can be secured to the counter top by

using the brackets supplied.

a. Locate square openings on exterior body of

drop unit. Insert securing bracket as shown.

Tighten screw to anchor the unit tightly to

cabinet top.

b. Seal top flange to the counter top by using

food grade silicone sealant.

4. The air cooled self contained units require

a sufficient amount of cool clean air. The

mechanical housing (except on 100-CW

appliances) can be rotated so that the condenser

intake air can be in direct line with the cabinet

fresh air opening.

a. Loosen wings nuts located under cold pan

body and rotate carriage to desired location.

b. Tighten wing nuts when rotation is complete.

c. Loosen wing nuts on each side of condenser

shroud and extend to fresh air opening.

d. Tighten wing nuts on each side of condenser

shroud.

Cross ventilation in the cabinet is recommended

to maintain ambient temperature 86°F (30°C) or

less.

5. DO NOT store or use any flammable liquids or

allow flammable vapors in the vicinity of this

appliance or any other appliance.

6. This appliance must be kept free and clear of

any combustible materials.

LEVELING

The cold well

should be

leveled before

the electrical supply is

connected. Level the appliance from side-

to-side and front-to-back with the use of a spirit

level.

NOTE

It is important to apply a food grade silicone

underneath the decor flange to seal flange to

the counter top.

INSTALLATI ON

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊx

INSTALLATI ON

18-1/2" (470mm)

27" (686mm)

2-1/2" (64mm)

10-1/2" (267mm)

16-7/16" (418mm)

25-1/8" (638mm)

27-1/2" (699mm)

100-CW

31-7/16" (799mm)

10-1/2" (267mm)

29-3/8" (746mm)

25-1/8" (638mm)

2-1/2" (64mm)

27" (686mm)

31-7/16 (799mm)

27-1/2" (699mm)

D I M E NSI ONS

200-CW

OPTIONS AND ACCESSORIES

12" (305mm) Half Size / Third-Size Divider Bars 1014395

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊÈ

INSTALLATI ON

D I M E NSI ONS

44-1/4" (1124mm)

27" (686mm)

2-1/2" (64mm)

44-1/4" (1124mm)

10-1/2" (267mm)

42-1/4" (1072mm)

25-1/8" (638mm)

27-1/2" (699mm)

300-CW

57-1/4" (1453mm)

27" (686mm)

2-1/2" (64mm)

10-1/2" (267mm)

57-1/4" (1453mm)

55-3/16" (1401mm)

25-1/8" (638mm)

27-1/2" (699mm)

400-CW

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊÇ

INSTALLATI ON

2-1/2" (64mm)

27" (686mm)

10-1/2" (267mm)

70-1/8" (1781mm)

68-1/16" (1729mm)

25-1/8" (638mm)

70-1/8" (1781mm)

27-1/2" (699mm)

D I M E NSI ONS

600-CW

500-CW

83" (2108mm)

27" (686mm)

2-1/2" (64mm)

10-1/2" (267mm)

83" (2108mm)

25-1/8" (638mm)

81" (2056mm)

27-1/2" (699mm)

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊn

100-CW 200-CW 300-CW 400-CW 500-CW 600-CW

Maximum Capacity 36 lb

(16.3 kg)

72 lb

(32.6 kg)

108 lb

(48.9 kg)

144 lb

(65.2 kg)

180 lb

(81.5 kg)

216 lb

(97.8 kg)

Maximum Volume 22 qt

(21 L)

44 qt

(42 L)

66 qt

(62 L)

88 qt

(84 L)

110 qt

(105 L)

132 qt

(126 L)

Full-Size Pans* - 12" x 20" x 6"

GN 1/1 (325mm x 530mm x 176mm)

1 2 3 4 5 6

Half-Size Pans* - 12" x 10" x 6"

GN 1/2 (325mm x 265mm x 176mm)

2 4 6 8 10 12

Third-Size Pans* - 12" x 6" x 6"

GN 1/3 (325mm x 176mm x 176mm)

3 6 9 12 15 18

* WILL ALSO ACCEPT 2-1/2" (65mm) DEEP PANS AND 4" (102mm) DEEP PANS

product\pan capacity (BASED ON 6" [176mm] DEEP PANS)

INSTALLATI ON

ROUGH CUT OPE N I N G S

MODEL CO U NTE R TOP OPEN I N G AI R LOUVER OPENING

100-CW ONE PAN

16-7/8" L x 25-1/2" W

(429mm x 648mm)

21" H x 16" W

(533mm x 406mm)

200-CW

TWO PAN

29-7/8" L x 25-1/2" W

(759mm x 648mm)

21" H x 16" W

(533mm x 406mm)

300-CW

THREE PAN

42-3/4" L x 25-1/2" W

(1085mm x 648mm)

21" H x 16" W

(533mm x 406mm)

400-CW

FOUR PAN

55-5/8" L x 25-1/2" W

(572mm x 648mm)

21" H x 16" W

(533mm x 406mm)

500-CW

FIVE PAN

68-1/2" L x 25-1/2" W

(1740mm x 648mm)

21" H x 16" W

(533mm x 406mm)

600-CW

SIX PAN

81-1/2" L x 25-1/2" W

(2070mm x 648mm)

21" H x 16" W

(533mm x 406mm)

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊ

INSTALLATI ON

PLACEMENT DETAILS

Retractable vent housing must

be extended out to engage

louver panel then locked down

Air exhaust

Air intake

Compressor cage

MODEL A B C D F

100-CW ONE PAN

18-1/2"

(470mm)

27"

(686mm)

16-7/8"

(429mm)

25-1/2"

(648mm)

1-1/2" – 7-1/2"

(38mm – 191mm)

200-CW

TWO PAN

31-7/16"

(799mm)

27"

(686mm)

29-7/8"

(759mm)

25-1/2"

(648mm)

1-1/2" – 7-1/2"

(38mm – 191mm)

300-CW

THREE PAN

44-1/4"

(1124mm)

27"

(686mm)

42-3/4"

(1085mm)

25-1/2"

(648mm)

1-1/2" – 7-1/2"

(38mm – 191mm)

400-CW

FOUR PAN

57-1/4"

(1453mm)

27"

(686mm)

55-5/8"

(572mm)

25-1/2"

(648mm)

1-1/2" – 7-1/2"

(38mm – 191mm)

500-CW

FIVE PAN

70-1/8"

(1781mm)

27"

(686mm)

68-1/2"

(1740mm)

25-1/2"

(648mm)

1-1/2" – 7-1/2"

(38mm – 191mm)

600-CW

SIX PAN

83"

(2108mm)

27"

(686mm)

81-1/2"

(2070mm)

25-1/2"

(648mm)

1-1/2" – 7-1/2"

(38mm – 191mm)

Louver panel

Dim "F" +4"

(critical)

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊ£ä

INSTALLATI ON

PLACEMENT DETAILS

To roTaTe compressor (illustration 1),

loosen 4 mounting bolts on the top of the

compressor cage 1 and 1/2 turns. Hold

compressor cage by the frame and rotate

90° to desired position. Retighten bolts.

To exTend venT housing (illustration 2),

remove louver and loosen wing nuts

located on the side of housing. Extend the

housing until it engages with the louvered

opening. Finger tighten wing nuts.

Reinstall louver.

Side of unit bolt pattern

Wing Nuts

Rear of unit bolt pattern

Illustration 1

Illustration 2

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊ££

INSTALLATI ON

E L ECTRICAL CONNECT I ON

1. Drains must be plumbed to all applicable local code requirements.

2. Moisture collecting from improper drainage can create a slippery surface on the

floor and a hazard to employees.

PLU M BIN G CONNECT I ON

inStaLLation rEQuirEMEntS

Counter top material must be water resistant.

Distance of 3/4" (19mm) or more between top rims of wells to

ensure easy cleaning.

Must be installed level.

Must not be installed in any area where it may be directly affected

by steam, grease, dripping water, high temperatures, or any other

severely adverse conditions.

Must not be installed under a hood.

Avoid installation under a 4-way ceiling diffuser.

Outdoor use is not recommended.

Drain or catch basin is required.

LED lighting is recommended for overhead lighting

cLEarancE rEQuirEMEntS

4" (102mm) in front of dual air movement louver

ELEctricaL

VOLTAGE PHASE CYCLE/HZ AMPS

KW PLUG CONFIG.

115 1 60 5.0 .6

NEMA 5-15P

15A-125V PLUG

9' (229

) LONG CORD

1. An identification tag is permanently mounted

on the front control panel of the appliance.

2. This appliance is equipped with a three-prong

grounding plug. For your protection against

shock hazard this appliance should be plugged

directly into a properly grounded three-prong

receptacle. Do not cut or remove the grounding

prong from this plug. Plug the unit into a

properly grounded receptacle ONLY, positioning

the unit so that the plug is easily accessible in

case of an emergency. Arcing will occur when

connecting or disconnecting the unit unless all

controls are in the “OFF” position.

3. Proper receptacle or outlet configuration or

permanent wiring for this unit must be installed

by a licensed electrician in accordance with

applicable local electrical codes.

4. It is important that a voltage reading be made

at the compressor motor electrical connections

while the unit is in operation to verify that the

correct voltage required by the appliance is being

supplied. Low or high voltage can detrimentally

affect operation and void the warranty.

5. The cold well unit should have its own dedicated

line. Condensing units are designed to operate

with a voltage fluctuation of plus or minus 10%

of the voltage indicated on the unit data tag. Burn

out of a condensing unit due to exceeding voltage

limits will void the warranty.

DANGER

ENSURE POWER SOURCE

MATCHES VOLTAGE IDENTIFIED

ON APPLIANCE RATING TAG.

DANGER

ELECTRICAL CONNECTIONS MUST

BE MADE BY A QUALIFIED SERVICE

TECHNICIAN IN ACCORDANCE WITH

APPLICABLE ELECTRICAL CODES.

DANGER

To avoid electrical shock, this

appliance MUST be adequately

grounded in accordance with local

electrical codes or, in the absence of

local codes, with the current edition

of the National Electrical Code ANSI/

NFPA No. 70. In Canada, all electrical

connections are to be made in

accordance with CSA C22.1, Canadian

Electrical Code Part 1 or local codes.

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊ£Ó

INSTALLATI ON CHECKLI ST

PR I OR TO START-UP

Locate nameplate and record the serial number. It will be necessary when ordering

replacement parts or requesting warranty service.

Follow cut out dimension provided for specic models to properly size the opening for

your drop in.

Condenser coil must be facing a ventilated opening in the cabinet.

Check cord and plug of unit to assure no damage has occurred to these components.

Assure all refrigeration lines are clear of obstruction before, during, and after being

installed into the counter.

Check all sheet metal surrounding the mechanical compartment to assure no damage has

occurred in these areas.

The cold well should have its own dedicated electrical supply line.

Plumbing connections have been made.

Plug in unit and turn ON main on/off power switch.

Allow unit time to cool down to temperature. A layer of frost will form and remain

around the inside perimeter of the rail.

Conrm that the unit is holding temperature. Set control to desired temperature for your

particular ambient and altitude.

NOTE: Failure to follow installation guidelines and recommendations

may void the warranty on your unit.

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊ£Î

OPE RATI N G INSTRUCT I ONS

1. DO NOT ADD WATER TO COLD WELL

Alto-Shaam cold wells do not require the addition

of water. Adding water is not recommended

since water will accelerate the deterioration of

the product and may damage the unit voiding the

warranty.

2. P L A CE PAN DIVIDERS AND EMPTY PANS IN

THE WELLS

NOTE: No matter what type of pan configuration

chosen, pan separator bars or divider bars must

be used to close all gaps between pans, and all

gaps between the pans and the edges of the

wells. If these gaps are not closed, cold will

escape, distribution will be uneven, and uniform

temperature will be difficult to maintain.

This is a VERY important requirement to follow

whenever this appliance is in use.

3. P RESS THE "ON" SWITCH AND BEGIN TO

PRECHILL THE COLD WELL

The cold temperature control is preset at the

factory. Due to varying conditions (i.e. elevation,

food product,

type of

operation, etc.)

adjustments

can be made

(within limits)

by turning

the control

dial until

the desired

temperature is

reached. Please

allow 24 hours

between adjustments. The control knob is located

on the unit base by the compressor. Turning the

knob clockwise will result in increased cooling.

Keep the arrow on the knob pointed within

the green arc. Turning it clockwise beyond the

green can result in freeze-up, while turning it

counterclockwise beyond the green arc will shut

the compressor off.

NOTE: If your cold pan temperature remains

too warm and your temperature control is at the

maximum setting, please contact your service

technician.

The unit should be pre chilled for a minimum of

30 minutes before loading the unit with chilled

food. If the unit is started at the full off position,

30-45 minutes may be necessary for unit to cool

down.

4. L O A D CHILLED FOODS INTO THE

APPLIANCE

After pre chilling, place cold foods into the pre

chilled pans located in the appliance or exchange

the pans with pre-filled product pans. This

appliance is designed for the purpose of cold food

holding. Product entering the cold pan must be at

40°F (4°C) or less.

All pan divider bars required must be utilized

at all times with the pan configuration chosen.

Before loading food into the unit, use a pocket-

type thermometer to make certain all products

are within the cold safe zone with an internal

temperature of 36° to 40°F (2° to 4°C).

5. C H E C K FOOD TEMPERATURES

After all products are loaded into the unit,

periodically use a pocket thermometer to check

each item to make certain the correct temperatures

are being maintained. Proper temperature range

is between a minimum of 36° to 40°F (2° to 4°C).

6. SERVE FRESH, COLD FOOD

Keep cold foods looking fresh. Occasionally stir

or rotate food as needed. Wipe spills immediately

to ensure maximum eye appeal and to ease end of

day cleanup.

7. EVENING SHUTDOWN

Remove product at the end of the day's

preparation. Turn off the cold well with the switch

located on the base by the compressor. Cleaning

may be performed once the frost has melted off

the rail surface.

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊ£{

PROTECTING STAINLESS STEEL SURFACES

It is important to guard against corrosion

in the care of stainless steel

surfaces. Harsh, corrosive,

or inappropriate chemicals

can completely destroy the

protective surface layer

of stainless steel. Abrasive

pads, steel wool, or metal implements will abrade

surfaces causing damage to this protective coating

and will eventually result in areas of corrosion.

Even water, particularly hard water that contains

high to moderate concentrations of chloride, will

cause oxidation and pitting that result in rust

and corrosion. In addition, many acidic foods

spilled and left to remain on metal surfaces are

contributing factors that will corrode surfaces.

Proper cleaning agents, materials, and

methods are vital to maintaining the appearance

and life of this appliance. Spilled foods should be

removed and the area wiped as soon as possible

but at the very least, a minimum of once a day.

Always thoroughly rinse surfaces after using a

cleaning agent and wipe standing water as quickly

as possible after rinsing.

CLEANING AGENTS

Use non-abrasive cleaning products designed for

use on stainless steel surfaces. Cleaning agents

must be chloride-free compounds and must not

contain quaternary salts. Never use hydrochloric

acid (muriatic acid) on stainless steel surfaces.

Always use the proper cleaning agent at the

manufacturer's recommended strength.

Contact your local cleaning supplier for

product recommendations.

CLEANING MATERIALS

The cleaning function can usually be accomplished

with the proper cleaning agent and a soft, clean

cloth. When more aggressive methods must be

employed, use a non-abrasive scouring pad on

difficult areas and make certain to scrub with the

visible grain of surface metal to avoid surface

scratches. Never use wire brushes, metal scouring

pads, or scrapers to remove food residue.

CLEANING AND PREVENTATIVE MAINTENANCE

CAUTION

TO PROTECT STAINLESS STEEL

SURFACES, COMPLETELY AVOID

THE USE OF ABRASIVE CLEANING

COMPOUNDS, CHLORIDE BASED

CLEANERS, OR CLEANERS

CONTAINING QUATERNARY SALTS.

NEVER USE HYDROCHLORIC ACID

(MURIATIC ACID) ON STAINLESS

STEEL. NEVER USE WIRE

BRUSHES, METAL SCOURING

PADS OR SCRAPERS.

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊ£x

C ARE AND CLE ANI N G

INTERIOR:

1. Disconnect appliance from the power source. Let

unit begin to return to ambient temperature.

2. After the frost has melted off the rail of the

appliance, remove all detachable items such

as pans and divider bars. Clean these items

separately.

3. Drain water from the wells daily.

4. Remove any food scraps.

5. Wipe the interior metal surfaces with a paper towel

to remove any remaining food debris.

6. Clean interior with a damp cloth or sponge and

any good commercial detergent at the

recommended strength.

7. For dried-on food deposits, use a non-caustic and

non-toxic commercial oven cleaner appropriate

for the interior surface. Follow the product

manufacturer’s instructions carefully for the use

of this product. Any commercial oven cleaner

must be approved for use on food contact areas.

Remove soil with the use of a plastic scouring

pad.

8. Rinse surfaces by wiping with a clean cloth or

sponge and clean warm water.

9. Remove excess water with a sponge and wipe dry

with a clean cloth or air dry. Leave area open

until interior is completely dry. Replace divider

bars and pans.

10. Interior can be wiped with a sanitizing solution

after cleaning and rinsing. This solution must be

approved for use on stainless steel food contact

surfaces.

DO NOT USE ABRASIVE CLEANING COMPOUNDS.

Always follow appropriate state or local health

(hygiene) regulations regarding all applicable

cleaning and sanitation requirements for food

service equipment.

NOTE: Always allow the frost to melt off the rail

of the appliance before cleaning.

CL E AN THE APPLIANCE DAILY.

NOTE:

Completely avoid

the use of abrasive cleaning

compounds, chloride-based

cleaners, or cleaners containing

quaternary salts. To protect

metal finish on stainless steel,

never use hydrochloric acid

(muriatic acid).

The cleanliness and

appearance of this appliance

will contribute considerably

to operating efficiency and

savory, appetizing food.

Good equipment kept clean

works better and lasts longer.

DANGER

DISCONNECT UNIT FROM

POWER SOURCE BEFORE

CLEANING OR SERVICING.

DANGER

AT NO TIME SHOULD THE INTERIOR

OR EXTERIOR BE STEAM CLEANED,

HOSED DOWN, OR FLOODED WITH

WATER OR LIQUID SOLUTION OF

ANY KIND. DO NOT USE WATER JET

TO CLEAN.

SEVERE DAMAGE OR

ELECTRICAL HAZARD

COULD RESULT.

WARRANTY BECOMES VOID IF

APPLIANCE IS FLOODED

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊ£È

Food ﬂ avor and aroma are usually so closely related

that it is diﬃ cult, if not impossible, to separate them.

There is also an important, inseparable relationship

between cleanliness and food ﬂ avor. Cleanliness, top

operating eﬃ ciency, and appearance of equipment

contribute considerably to savory, appetizing foods. Good

equipment that is kept clean, works be er and lasts longer.

Most food imparts its own particular aroma and many

foods also absorb existing odors. Unfortunately, during

this absorption there is not distinction between GOOD

and BAD odors. The majority of objectionable ﬂ avors

and odors troubling food service operations are caused by

bacteria growth. Sourness, rancidity, mustiness, stale or

other OFF ﬂ avors are usually the result of germ activity.

The easiest way to insure full, natural food ﬂ avor is

through comprehensive cleanliness. This means good

control of both visible soil (dirt) and invisible soil

(germs). A through approach to sanitation will provide

essential cleanliness. It will assure an a ractive

appearance of equipment, along with maximum eﬃ ciency

and utility. More importantly, a good sanitation program

provides one of the key elements in the prevention of

food-borne illnesses.

A controlled holding environment for prepared foods is

just one of the important factors involved in the prevention

of food-borne illnesses. Temperature monitoring and

control during receiving, storage, preparation, and the

service of foods are of equal importance.

The most accurate method of measuring safe temperatures

of both hot and cold foods is by internal product

temperature. A quality thermometer is an eﬀ ective tool for

this purpose, and should be routinely used on all products

that require holding at a speciﬁ c temperature.

A comprehensive sanitation program should focus on

the training of staﬀ in basic sanitation procedures. This

includes personal hygiene, proper handling of raw foods,

cooking to a safe internal product temperature, and

the routine monitoring of internal temperatures from

receiving through service.

Most food-borne illnesses can be prevented through

proper temperature control and a comprehensive

program of sanitation. Both these factors are important

to build quality service as the foundation of customer

satisfaction. Safe food handling practices to prevent food-

borne illness is of critical importance to the health and

safety of your customers.

HACCP, an acronym for Hazard Analysis (at) Critical

Control Points, is a quality control program of operating

procedures to assure food integrity, quality, and safety.

Taking steps necessary to augment food safety practices

is both cost eﬀ ective and relatively simple. While HACCP

guidelines go far beyond the scope of this manual,

additional information is available by contacting:

CENTER FOR FOOD SAFETY AND APPLIED

NUTRITION FOOD AND DRUG ADMINISTRATION

1-888-SAFEFOOD

INTERNAL FOOD PRODUCT TEMPERATURES

HOT FOODS

DANGER ZONE 40° TO 140°F (4° TO 60°C)

CRITICAL ZONE 70° TO 120°F (21° TO 49°C)

SAFE ZONE 140° TO 165°F (60° TO 74°C)

COLD FOODS

DANGER ZONE ABOVE 40°F (ABOVE 4°C)

SAFE ZONE 36° TO 40°F (2° TO 4°C)

FROZEN FOODS

DANGER ZONE ABOVE 32°F (ABOVE 0°C)

CRITICAL ZONE 0° TO 32°F (-18° TO 0°C)

SAFE ZONE 0°F or below (-18°C or below)

S ANI TATI ON

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊ£Ç

PREVENTATIVE MAI NTE NANCE

ALTO-SHAAM STRONGLY SUGGESTS A PREVENTATIVE MAINTENANCE PROGRAM

which would include the following monthly procedures:

TASK WHY HO W

Clean all condenser coils

Condenser coils are a critical component in

the life of the compressor and must remain

clean to assure proper air ﬂow and heat

transfer.

Clean the condenser coils with coil

cleaner and/or a vacuum, cleaner and

brush.

Brush coil in direction of ﬁns, (usually

vertical) to avoid damage or restrict air

from passing through the condenser.

Clean fan blade on the

condensing unit

>ÊL>`iÊV>ÊViVÌÊ`ÕÃÌÊ>`ÊÌÀ>ÃviÀÊÌ>ÌÊ

dust into the condenser coils.

Clean the fan blade with a vacuum,

cleaner and brush.

NOTE: Do not use sharp utensils.

Use of any filter over the condenser coil may result in poor performance of the equipment.

The factory does not recommend the use of any auxiliary filter. Any failures of the unit as

a result of an auxiliary filter will not be covered under warranty.

5-Year Limited

Warranty on

self-contained

compressor

Effective from date of

shipment. (EXCLUDES LABOR)

 ÎÈäÎÎÊ,iÛ°Êä®ÊUÊ`Ê`ÊÀ«Ê7iÊ"«iÀ>ÌÊEÊ>ÀiÊ>Õ>ÊUÊ£n

TROUBL E SH OOTI N G

PROBL E M POSSIBLE CA U S E RE M EDY

UNIT WILL NOT COOL

Thermostat off Turn thermostat on

Unit unplugged Plug in appliance

Circuit breaker tripped Replace breaker

Unknown problem Call service agency

UNIT DOESN'T RUN

No power to unit Plug in appliance (check power switch)

Temperature control turned off Check temperature control

Temperature control faulty Test temperature control

Compressor overheated Clean condenser coil

Condenser fan faulty Service condenser fan

Overload protector faulty Test overload

Compressor relay faulty Test relay

Compressor faulty Call service agency

UNIT SHORT CYCLES

Condenser coil dirty Clean coil

Condenser fan faulty Service fan and motor

Compressor faulty Call service agency

Overload repeatedly tripping Check outlet voltage

UNIT RUNS CONSTANTLY

Condenser coil dirty Clean coil

Condenser fan faulty Service condenser motor

Low on refrigerant Call service agency

UNIT TOO COLD

Temperature control set too low Adjust control to raise setting

Temperature control faulty Test control

UNIT NOISY

Compressor mountings loose or hardened

Tighten or replace compressor

mountings

Condenser fan damaged or hitting fan

shroud

Inspect condenser fan

La page charge ...

Alto-Shaam 300-CW Installation Operation & Maintenance

Marque: Alto-Shaam

Modèle: 300-CW

Catégorie: Chauffe-plats

Taper: Installation Operation & Maintenance

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Alto-Shaam 300-CW

Documents connexes

Alto-Shaam ASF-60DS Mode d'emploi

Alto-Shaam 300-CW Installation Operation & Maintenance

Ce manuel convient également à

Alto-Shaam 300-CW Installation Operation & Maintenance

dans d''autres langues

Documents connexes

Autres documents