GE AEE23DM Le manuel du propriétaire

Safety Instructions ............. 2, 3

Operating Instructions

Controls ........................... 4–6

Care and Cleaning

Air Filter ..............................6

Outdoor Coils .........................6

Installation Instructions ......7–13

Troubleshooting Tips ............14

Normal Operating Sounds ............14

Consumer Support

Consumer Support .......... Back Cover

Ownership Registration for

Customers in Canada only ........ 15, 16

Warranty for Customers

in Canada ...........................18

Warranty for Customers

in the U.S.A. ..........................17

49-7624 01-10 GE

AEE23

Owner’s Manual and

Installation Instructions

Write the model and serial numbers here:

Model # _________________________

Serial # __________________________

Find these numbers on a label on the side of

the air conditioner.

Air Conditioners

GEAppliances.com

Room

Climatiseur

Acondicionador

de aire

Manuel d’utilisation et

instructions d’installation

Manual del propietario

y instrucciones de

instalación

La section française commence à la page 19

La sección en español empieza en la página 37

In Canada, contact us at:

www.GEAppliances.ca

2

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock

or personal injury.

n Use this appliance only for its intended

purpose as described in this Owner’s

Manual.

n This air conditioner must be properly

installed in accordance with the Installation

Instructions before it is used.

n Never unplug your air conditioner by pulling

on the power cord. Always grip plug firmly

and pull straight out from the receptacle.

n Replace immediately all electric service

cords that have become frayed or otherwise

damaged. A damaged power supply cord

must be replaced with a new power supply

cord obtained from the manufacturer and

not repaired. Do not use a cord that shows

cracks or abrasion damage along its length

or at either the plug or connector end.

n Turn the unit OFF and unplug your air

conditioner before cleaning.

n GE does not support any servicing of the

air conditioner. We strongly recommend

that you do not attempt to service the air

conditioner yourself.

n For your safety…do not store or use

combustible materials, gasoline or other

flammable vapors or liquids in the vicinity

of this or any other appliance.

n All air conditioners contain refrigerants,

which under federal law must be removed

prior to product disposal. If you are getting

rid of an old product with refrigerants, check

with the company handling disposal about

what to do.

n If the receptacle does not match the plug,

the receptacle must be changed out by a

qualified electrician.

n These R410A air conditioning systems

require contractors and technicians to

use tools, equipment and safety standards

approved for use with this refrigerant.

DO NOT use equipment certified for

R22 refrigerant only.

SAFETY PRECAUTIONS

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord.

For personal safety, this appliance must be properly

grounded.

DO NOT use an adapter plug with this appliance.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall outlet

to minimize the possibility of electric shock

hazard from this appliance.

Power cord includes a current interrupter device.

A test and reset button is provided on the plug

case. The device should be tested on a periodic

basis by first pressing the TEST button and

then the RESET button while plugged into the

outlet. If the TEST button does not trip or if the

RESET button will not stay engaged, discontinue

use of the air conditioner and contact a qualified

service technician.

Have the wall outlet and circuit checked by

a qualified electrician to make sure the outlet

is properly grounded.

Where a 2-prong wall outlet is encountered,

it is your personal responsibility and obligation to

have it replaced with a properly grounded

3-prong wall outlet.

The air conditioner should always be plugged

into its own individual electrical outlet which has

a voltage rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

See the Installation Instructions, Electrical

Requirements section for specific electrical

connection requirements.

HOW TO CONNECT ELECTRICITY

Safety InstructionsOperating Instructions

Care and Cleaning

Installation InstructionsTroubleshooting TipsConsumer Support

3

Consumer SupportTroubleshooting TipsInstallation Instructions

Care and Cleaning

Operating Instructions Safety Instructions

GEAppliances.com

WARNING!

Because of potential safety hazards under certain

conditions, we strongly recommend against the use

of an extension cord.

However, if you must use an extension cord,

it is absolutely necessary that it be a UL-listed,

14-gauge, 3-wire grounding-type appliance

extension cord having a grounding-type plug

and outlet and that the electrical rating of the

cord be 15 amperes (minimum) and 125 volts.

CAUTION:

DO NOT use an extension cord with any of the

230/208 volt models.

USE OF EXTENSION CORDS—115-Volt models only

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY

.

SAVE THESE INSTRUCTIONS

4

Safety InstructionsOperating Instructions

Care and Cleaning

Installation InstructionsTroubleshooting TipsConsumer Support

About the controls on the air conditioner.

Features and appearance will vary.

TEMP CONTROL MODE CONTROL

Temp Control

The temp control is used to maintain

the room temperature. The compressor

will cycle on and off to keep the room at

the same level of comfort. Turn the knob

clockwise to Cooler (blue) and the indoor

air will become cooler. Turn the knob

counterclockwise to Warmer (red) and

the indoor air will become warmer.

Mode Control

Hi Cool and Low Cool provide cooling with

different fan speeds.

Hi Heat and Low Heat provide heating with

different fan speeds.

Fan Only setting provides air circulation

and filtering without cooling or heating.

NOTE: If you move the mode control

from a cool setting to Off, a fan setting

or a heat setting, wait at least 3 minutes

before switching back to a cool setting.

Cooling Descriptions

For Normal Cooling—Select Hi Cool

or Low Cool with the temp control at

midpoint.

For Maximum Cooling—Select Hi Cool with

the temp control turned clockwise as far as

possible.

For Quieter and Nighttime Cooling—Select

Low Cool with the temp control at midpoint.

Heating Descriptions

For Normal Heating—Select Hi Heat

or Low Heat with the temp control at

midpoint.

For Maximum Heating—Select Hi Heat with

the temp control turned counterclockwise

as far as possible.

For Quieter & Nighttime Heating—Select

Low Heat with the temp control at

midpoint.

Controls

Consumer SupportTroubleshooting TipsInstallation Instructions

Care and Cleaning

Operating Instructions Safety Instructions

5

Air Direction

Use the lever to adjust the air direction left and right

only.

Fingertip pressure on the horizontal louvers

adjusts the air direction up or down.

GEAppliances.com

Additional important information.

6

Safety InstructionsOperating Instructions

Care and Cleaning

Installation InstructionsTroubleshooting TipsConsumer Support

Normal Operating Sounds

n You may hear a pinging noise caused by

water being picked up and thrown against the

condenser on rainy days or when the humidity

is high. This design feature helps remove

moisture and improve efficiency.

n You may hear the thermostat click when the

compressor cycles on and off.

n Water will collect in the base pan during

high humidity or on rainy days. The water

may overflow and drip from the outdoor side

of the unit.

n The fan may run even when the compressor

does not.

Air Filter

The air filter behind the front grille should be checked

and cleaned at least every 30 days or more often if

necessary.

To remove:

Open the inlet grille by pulling downward on the tabs

at the top upper corners of the inlet grille until the

grille is in a 45° position. Remove the filter.

Clean the filter with warm, soapy water. Rinse and let

the filter dry before replacing it. Do not clean the filter

in a dishwasher.

CAUTION: DO NOT operate the air

conditioner without a filter because dirt and lint

will clog it and reduce performance.

Outdoor Coils

The coils on the outdoor side of the air conditioner

should be checked regularly. If they are clogged with

dirt or soot, they may be professionally cleaned.

Turn the air conditioner off and remove the plug from

the wall outlet before cleaning.

To clean, use water and a mild detergent.

Do not use bleach or abrasives.

Grille and Case

Care and cleaning of the air conditioner.

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

•

IMPORTANT — Save these instructions

for local inspector’s use.

•

IMPORTANT — Observe all governing

codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Skill level – Installation of this appliance

requires basic mechanical skills.

• Completion time –

Approximately 1 hour

• We recommend that two people install

this product.

• Proper installation is the responsibility

of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

• You MUST use all supplied parts and use proper

installation procedures as described in these

instructions when installing this air conditioner.

Installation

Air Conditioner

Instructions

Some models require a 115/120-volt AC,

60-Hz grounded outlet protected with a

15-amp time-delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the

possibility of electric shock hazard. If the wall outlet

you plan to use is only a 2-prong outlet, it is your

responsibility to have it replaced with a properly

grounded 3-prong wall outlet.

Some models require 230/208-volt AC,

protected with a time-delay fuse or circuit

breaker. These models should be installed on

their own single branch circuit for best

performance and to prevent overloading

house or apartment wiring circuits, which

could cause a possible fire hazard from

overheating wires.

ELECTRICAL REQUIREMENTS

CAUTION:

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord.

Do not change the plug on the power cord

of this air conditioner.

Aluminum house wiring may present special

problems—consult a qualified electrician.

7

TOOLS YOU WILL NEED

Phillips head screwdriver

Ruler or tape measurePencil

Level

Scissors or knife

Flat-blade screwdriver

Power cord includes a current interrupter device. A

test and reset button is provided on the plug case. The

device should be tested on a periodic basis by first

pressing the TEST button and then the RESET button

while plugged into the outlet. If the TEST button does

not trip or if the RESET button will not stay engaged,

discontinue use of the air conditioner and contact a

qualified service technician.

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com

In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca

8

Installation Instructions

Window

locking bracket

(1)

Top

mounting

rail

Sill angle

bracket (2)

Right

accordion

panel

Foam top window

gasket (1)

Left

accordion

panel

Window

sash seal

PARTS INCLUDED

(Appearance may vary)

Top rail gasket (1)

Type A

screws (10)

Type C

screws (5)

Type E bolt

with nut (4)

V-supports (2)

Type F bolt

with nut (2)

Side rail (2)

STORM WINDOW REQUIREMENTS

A storm window frame will not allow the air

conditioner to tilt toward the outside, and will keep it

from draining properly.

To adjust for this, attach a piece of wood to the sill.

WOOD PIECES

WIDTH: 2”

LENGTH: Long enough to fit inside the window

frame.

THICKNESS: To determine the thickness, place a

piece of wood on the sill to make it 1/2″ higher

than the top of the storm window frame or the vinyl

frame.

Attach securely with nails or screws provided by the

installer.

Installation Instructions

WINDOW REQUIREMENTS

•These instructions are for a standard double-hung

window. You will need to modify them for other types

of windows.

•All supporting parts must be secured

to firm wood, masonry or metal.

•The electrical outlet must be within reach of the

power cord.

•Follow the dimensions in the table and illustration

for your model.

1

19 1/4”

(With accordion panels)

PREPARE THE AIR CONDITIONER

Remove the two control knobs.

Pull down the front panel and remove the filter.

Remove the front panel by lifting up at an

angle.

Remove the four front screws. Save them

for reinstalling the front housing.

Grasp the lower corners of the grille while

pressing in on the case sides with your

finger tips. Pull out to release and lift it up.

NOTE: Do not pull the bottom edge

toward you more than 3″ or you may

damage the tabs of the grille.

3

A

B

29” - 41”

2

1/2″ higher

than storm

window

frame

Storm window

frame

Wood

Sill

1/2″ higher

than vinyl frame

(on some windows)

Vinyl frame

9

C

D

Installation Instructions

10

Installation Instructions

PREPARE THE AIR CONDITIONER

(continues)

Remove the shipping screws located on

the top of the case.

Remove the ground screws from each

side of the case. Keep it in a safe location.

NOTE: Be sure to save this screw. You will need

them later in the installation.

Slide the air conditioner from the case by

gripping the base pan handle and pulling

forward while bracing the case. Do not

pull or lift on the styrofoam discharge area.

Your unit may come with internal

packaging. This packaging must be

removed prior to installing the air

conditioner back into the cabinet.

3

E

F

FRONT

Do not

pull

or lift

in this

area—

damage

to the

unit may

result

PREPARE THE CASE

Attach the top rail gasket to the bottom

of the top rail.

Install the top mounting rail with 4 type A

screws from the inside of the case. Press

firmly to drive the screws into the gasket

and through the top mounting rail.

Slide each side retainer onto the edge of

each according panel. The figure shows

the orientation of each accordion panel

and side retainer assembly relative to the

case from a top view of the unit.

Slide the left and right accordion panels

into the top and bottom mounting rails.

A

Top mounting rail

B

4

G

H

C

D

WINDOW FILLER PANEL

SIDE RETAINER

Top left

Top right

Bottom mounting rail

Installation Instructions

11

PREPARE THE WINDOW AND INSTALL

THE CASE

Cut the window sash seal to the proper length.

Peel off the backing and attach the seal to the

underside of the window sash.

Open the window and mark the center of

the window sill.

Carefully slide the case into the window

and center the case. Lower the window

behind the top mounting rail. Pull the

bottom of the case forward so that the

bottom mounting rail is tight against the

back of the window stool. Mount the case

to the window sill using 2 type C screws.

Drill pilot holes, if necessary.

5

PREPARE THE WINDOW AND INSTALL

THE CASE (continues)

Assemble the V-support and V-support

bracket with Type F nut and bolt

Position the V-supports

on the case bottom so

that they will be near

the outside wall. Attach

a V-support to each side

of the bottom of the case

with Type E bolts, 2 for

each support.

Adjust sill angle brackets to rest on sill.

Extend the left and right accordion panels

to the vertical window sashes. Drill pilot

holes and attach the top corners with 2 type

C screws.

5

2 type C screws

Stool

B

A

C

D

V-support

F

Sill

Bracket

G

E

Left

Sill angle

bracket

V-support Type

F bolt and nut

Right

Type E bolt

and nut

PREPARE THE CASE (continues)

Attach the side retainers to the case using 6

type A screws.

4

E

Type C

screw

Type C

screw

Installation Instructions

12

5

PREPARE THE WINDOW AND INSTALL

THE CASE (continues)

Cut the foam top window gasket to the

window width.

Stuff the foam

between the

glass and the

window to

prevent air and

insects from getting into the room.

NOTE: If the gasket supplied does not fit

your window, obtain appropriate material

locally to provide a proper installation seal.

H

CAUTION:

To prevent broken

glass or damage to

windows, on vinyl or

other similarly

constructed windows,

attach the window

locking bracket to the window side jamb.

Attach the window locking

bracket with one Type C

screw.

I

J

Wood

Vinyl

INSTALL THE AIR CONDITIONER

IN THE CASE (continues)

Replace the 2 screws removed earlier, one

on each side of the case.

IMPORTANT: THE GROUND SCREWS MUST BE

REINSTALLED TO ENSURE PROPER GOUND.

Attach the front grille to the case by inserting

the tabs on the grille into the slots on the

front top of the case. Push the grille in.

Replace the screws.

Install the filter and the front grille.

Plug in the air conditioner.

6

B

C

INSTALL THE AIR CONDITIONER

IN THE CASE

Slide the air conditioner into the case by

the base pan. Do not push on the controls,

styrofoam air discharge housing or the finned

coils. Make sure the air conditioner is firmly

seated.

6

A

Do not press on

these areas—

damage to the unit

may result

Base Pan

D

E

F

1313

Through-the-Wall Installation Instructions—Optional

The case may be installed through-the-wall

in both existing and new construction.

Read completely, then follow step-by-step.

NOTE: Obtain all materials locally for

mounting the air conditioner through-

the-wall.

IMPORTANT

Through-the-wall installation is not

appropriate if any of the side or top louvers

in the case will be obstructed by the wall.

All side and top louvers in the case must

project on the outdoor side of the wall.

The room side of the case must project

into the room far enough to maximize the

balance of the unit.

The case must be installed level from side-

to-side and with a slight tilt from front to

rear. Use a level; no more than a 1/2 bubble

will be the correct case slant to the outside.

Lintel angle is required to support bricks or

blocks above opening.

Flashing is required and should extend the

length of the opening to ensure no inside

cavity leakage occurs.

Remove the air conditioner from the case.

For specific instruction, refer to the Window

Installation Instructions.

Make certain that a wall receptacle is

available close to the hole location or make

arrangements to install a receptacle.

Place the case in the wall opening and

place wood support strips between the case

bottom and the flashing on both sides of the

bottom rail. They should be the same height

as the bottom rail and the same length as

the wall opening.

1

A

B

FINISH THE WALL OPENING

Caulk all four sides on the outdoor side of

the case to prevent moisture from getting

through to the interior wall. Use of flashing

(drip rail) will further prevent water from

dripping inside the wall and down the

outside of the building.

Place the air conditioner into the case.

For specific instruction, refer to the Window

Installation Instructions.

2

IMPORTANT (cont.)

Secure with 14 wood screws anchored at

least an inch into the wall support structure.

NOTE: Drill pilot holes, if necessary, for

proper installation. If the frame is oversized,

use shims to prevent case distortion.

1

D

A

B

Lintel angle

Plaster line

Trim molding (if

desired)

INSIDE

Bottom rail

Wood filler and

caulking (above and

below the flashing)

Air louvers (top

and sides must

project on the

outdoor side of

the wall)

OUTSIDE

Flashing

(Drip rail)

Case

bottom

Bottom

rail

Flashing

(Drip rail)

Wood support strips

Caulking

C

14

Safety InstructionsOperating Instructions

Care and Cleaning

Installation InstructionsTroubleshooting TipsConsumer Support

Troubleshooting Tips.

Normal Operating Sounds

n You may hear a pinging noise caused by

water being picked up and thrown against the

condenser on rainy days or when the humidity

is high. This design feature helps remove

moisture and improve efficiency.

n You may hear the thermostat click when the

compressor cycles on and off.

n Water will collect in the base pan during

high humidity or on rainy days. The water

may overflow and drip from the outdoor side

of the unit.

n The fan may run even when the compressor

does not.

Problem Possible Causes What To Do

Air conditioner The air conditioner •Make sure the air conditioner plug is pushed

does not start is unplugged. completely into the outlet.

The fuse is blown/circuit • Check the house fuse/circuit breaker box and replace

breaker is tripped. the fuse or reset the breaker.

Power failure. •The unit will automatically restart in the settings last

used after the power is restored.

•There is a protective time delay (approximately

3 minutes) to prevent tripping of the compressor

overload. For this reason, the unit may not start

normal cooling for 3 minutes after it is turned

back on.

The current interrupter •Press the RESET button located on the power cord plug.

device is tripped.

•If the RESET button will not stay engaged, discontinue

use of the air conditioner and contact a qualified

service technician.

Air conditioner does Airflow is restricted. • Make sure there are no curtains, blinds or furniture

not cool as it should blocking the front of the air conditioner.

The temp control may • In the Cool mode, press the Decrease pad.

not be set correctly.

The air filter is dirty. • Clean the filter at least every 30 days.

See the Care and Cleaning section.

The room may have been hot. • When the air conditioner is first turned on, you need

to allow time for the room to cool down.

Cold air is escaping. • Check for open furnace registers and cold air returns.

Cooling coils have iced up. •See “Air conditioner freezing up” below.

Air conditioner Ice blocks the air flow • Set the controls at High Fan or High Cool and set the

freezing up and stops the air conditioner thermostat to a higher temperature.

from cooling the room.

The remote control The batteries are inserted • Check the position of the batteries. They should be

is not working incorrectly. inserted in the opposite (+) and (–) direction.

The batteries may be dead. •Replace the batteries.

Water drips outside Hot, humid weather. • This is normal.

Water drips indoors The air conditioner is not • For proper water disposal, make sure the air conditioner

tilted to the outside. slants slightly from the case front to the rear.

Water collects in Moisture removed from air • This is normal for a short period in areas with little

base pan and drains into base pan. humidity; normal for a longer period in very humid areas.

15

OWNERSHIP REGISTRATION

P.O. BOX 1780

MISSISSAUGA, ONTARIO

L4Y 4G1

(FOR CANADIAN CONSUMERS ONLY)

Please place in envelope and mail to:

Veuillez mettre dans une enveloppe et envoyez à :

16

Consumer SupportTroubleshooting TipsInstallation Instructions

Care and Cleaning

Operating Instructions Safety Instructions

17

n Service trips to your home to teach you how to use the

product.

n Improper installation, delivery or maintenance. If you

have an installation problem, or if the air conditioner

is of improper cooling capacity for the intended use,

contact your dealer or installer. You are responsible for

providing adequate electrical connecting facilities.

n Failure of the product resulting from modifications to

the product or due to unreasonable use including failure

to provide reasonable and necessary maintenance.

n In commercial locations, labor necessary to move the

unit to a location where it is accessible for service by an

individual technician.

n Replacement of house fuses or resetting of circuit

breakers.

n Failure due to corrosion on models not corrosion-

protected.

n Damage to the product caused by improper power

supply voltage, accident, fire, floods or acts of God.

n Incidental or consequential damage caused by possible

defects with this air conditioner.

n Damage caused after delivery.

What Is Not Covered:

This warranty is extended to the original purchaser and any succeeding owner for products purchased for

home use within the USA. If the product is located in an area where service by a GE Authorized Servicer is

not available, you may be responsible for a trip charge or you may be required to bring the product to an

Authorized GE Service location for service. In Alaska, the warranty excludes the cost of shipping or service calls

to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty

gives you specific legal rights, and you may also have other rights which vary from state to state. To know

what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: General Electric Company. Louisville, KY 40225

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this

Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a

particular purpose, are limited to one year or the shortest period allowed by law.

GE Air Conditioner—One Year Limited Warranty. (For customers in the U.S.A.)

For The Period Of: GE Will Replace:

One Year Any part of the air conditioner which fails due to a defect in materials or workmanship.

From the date of the During this limited one-year warranty, GE will also provide, free of charge, all labor and related

original purchase service to replace the defective part.

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care

®

technician. To schedule service,

visit us on-line at GEAppliances.com, or call 800.GE.CARES

(800.432.2737). Have serial number and model number available

when calling for service.

Staple your receipt here.

Proof of the original purchase date

is needed to obtain service under

the warranty.

18

Safety InstructionsOperating Instructions Care and CleaningInstallation InstructionsTroubleshooting TipsConsumer Support

GE Air Conditioner—One-Year Limited Warranty. (For customers in Canada)

n Service trips to your home to teach you how to use the

product.

n Improper installation, delivery or maintenance. If you

have an installation problem, or if the air conditioner

is of improper cooling capacity for the intended use,

contact your dealer or installer. You are responsible for

providing adequate electrical connecting facilities.

n Failure of the product resulting from modifications to

the product or due to unreasonable use including failure

to provide reasonable and necessary maintenance.

n In commercial locations, labor necessary to move the

unit to a location where it is accessible for service by an

individual technician.

n Replacement of house fuses or resetting of circuit

breakers.

n Failure due to corrosion on models not corrosion-

protected.

n Damage to the product caused by improper power

supply voltage, accident, fire, floods or acts of God.

n Incidental or consequential damage caused by possible

defects with this air conditioner.

n Damage caused after delivery.

What Is Not Covered:

This warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada

for home use within Canada. In-home warranty service will be provided in areas where it is available and

deemed reasonable by Mabe to provide.

Some provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above

exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights

which vary from province to province. To know what your legal rights are in your province, consult your local or

provincial consumer affairs office.

Warrantor: Mabe Canada Inc.,

Burlington, Ontario

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this

Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a

particular purpose, are limited to one year or the shortest period allowed by law.

For The Period Of: Mabe Will Replace:

One Year Any part of the air conditioner which fails due to a defect in materials or workmanship.

From the date of the During this limited one-year warranty, Mabe will also provide, free of charge, all labor and related

original purchase service to replace the defective part.

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care

®

technician. For service, call

1.800.561.3344. Please have serial number and model number

available when calling for service.

Staple your receipt here.

Proof of the original purchase date

is needed to obtain service under

the warranty.

Consignes de sécurité .............20, 21

Consignes d’utilisation

Commandes ..........................22–24

Entretien et nettoyage

Filtre à air ................................24

Serpentins extérieurs .....................24

Instructions de montage ..........25–31

Conseils de dépannage ..............32

Bruits normaux de fonctionnement ........32

Assistance à la clientèle

Assistance à la clientèle ...................36

Garantie ..................................35

Enregistrement du titre

de propriété ...........................33, 34

Inscrivez ici les numéros de modèle et de série :

Numéro de modèle : ____________________

Numéro de Série : _____________________

Vous trouverez ces numéros sur l’étiquette

apposée sur le côté du climatiseur.

19

Au Canada, visitez-nous au :

www.electromenagersge.ca

AEE23

Assistance à

la clientèle

Conseils de

dépannage

Instructions

de montage

Entretien et

nettoyage

Consignes

d’utilisation

Consignes

de sécurité

20

IMPORTANTES CONSIGNES DE SÉCURITÉ.

VEUILLEZ LIRE TOUTES LES CONSIGNES AVANT UTILISATION.

AVERTISSEMENT!

Pour votre sécurité, les informations contenues dans ce manuel doivent être suivies afin de minimiser

les risques d’incendie, de chocs électriques ou de blessures corporelles.

n N’utilisez cet appareil qu’aux fins prévues

décrites dans le manuel d’utilisation.

n Ce climatiseur doit être correctement

installé conformément aux Instructions

d’Installation avant toute utilisation.

n Ne débranchez jamais votre climatiseur en

tirant sur le cordon d’alimentation. Prenez

toujours fermement la fiche en main et tirez

pour la sortir de la prise.

n Remplacez immédiatement tout cordon

électrique usé ou endommagé. Un

cordon d’alimentation endommagé doit

être remplacé par un nouveau cordon

d’alimentation obtenu du fabricant. Ne

réparez pas le cordon endommagé. N’utilisez

pas un cordon fissuré ou présentant des

dommages dus aux frottements soit sur sa

longueur ou aux extrémités du côté de la

fiche ou du raccord.

n Eteignez votre climatiseur et débranchez-le

avant de le nettoyer.

n GE n’offre pas de service d’entretien pour

les climatiseurs. Nous vous recommandons

de ne pas essayer d’effectuer l’entretien de

votre climatiseur vous-même.

n Pour votre sécurité, ne stockez pas et

n’utilisez pas de matériaux combustibles,

d’essence ou d’autres vapeurs et liquides

inflammables dans les parages de cet

appareil ou de tout autre appareil.

n Tous les climatiseurs contiennent des

fluides frigorigènes qui, conformément, à la

législation fédérale doivent être retirés avant

la mise au rebut de l’appareil. Si vous mettez

au rebus un ancien appareil contenant des

fluides frigorigènes, vérifiez la procédure à

suivre auprès de la compagnie responsable

de l’élimination.

n Si la prise de courant est d’un format

différent de la fiche, cette prise doit être

changée par un électricien qualifié.

n Ces systèmes de climatisation R410A

nécessitent que les entrepreneurs et

techniciens adoptent des outils, du matériel

et des normes de sécurité approuvés pour

utilisation avec ce réfrigérant. N’utilisez pas

de matériel certifié pour le réfrigérant R22

uniquement.

CONSIGNES DE SÉCURITÉ

Ne coupez pas ou n’enlevez pas, sous aucun

prétexte, la troisième broche de mise à la terre

du cordon d’alimentation. Pour des raisons de

sécurité, cet appareil doit être correctement mis

à la terre.

N’utilisez PAS d’adaptateur avec cet appareil.

Le cordon d’alimentation de cet appareil est

équipé d’une fiche à trois broches (pour une

mise à la terre) qui s’adapte à la prise de courant

standard à 3 broches (pour une mise à la terre)

pour minimiser les risques de chocs électriques

par cet appareil.

Le cordon d’alimentation est équipé d’un

dispositif d’interruption du courant. Un bouton

d’essai et de réenclenchement est fourni

sur le boîtier de la prise. Vous devez tester le

mécanisme régulièrement en appuyant d’abord

sur le bouton TEST (essai) puis sur le bouton

RESET (réenclenchement) lorsque l’appareil est

branché. Si le bouton TEST (essai) ne bascule

pas ou si le bouton RESET (réenclenchement)

ne reste pas enclenché, cessez d’utiliser votre

climatiseur et appelez un technicien de service

qualifié.

Faites vérifier la prise murale et le circuit

électrique par un électricien qualifié pour

s’assurer que le système est correctement mis à

la terre.

Dans le cas d’une prise biphasée, l’installateur a

la responsabilité et l’obligation de la remplacer

par une prise triphasée correctement mise à la

terre.

Le climatiseur doit toujours être branché à sa

propre prise électrique d’une tension nominale

correspondant à celle indiquée sur sa plaque

signalétique.

Ceci permet d’obtenir un meilleur rendement

du climatiseur et évite de surcharger les circuits

électriques du domicile qui risque d’occasionner

un incendie en surchauffant.

Consultez les Consignes d’Installations, dans la

section Exigences Electriques pour les exigences

de branchements électriques particuliers.

BRANCHEMENTS ÉLECTRIQUES

Consignes

de sécurité

Consignes

d’utilisation

Entretien et

nettoyage

Instructions

de montage

Conseils de

dépannage

Assistance à

la clientèle

La page charge ...

GE AEE23DM Le manuel du propriétaire

Ce manuel convient également à

GE AEE23DM Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents